Scribd
Upload
342 views

Creating 1+1 Linear MSP

In a chain network, you need to create 1+1 linear MSP, to protect important services. In this way, The NE dual feeds services at the source end and selects either of the two services at the sink end. Fibers that are related to an linear MSP cannot be used by other protection subnets.

Uploaded by

Ayoub Mouhssine
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
342 views

Creating 1+1 Linear MSP

In a chain network, you need to create 1+1 linear MSP, to protect important services. In this way, The NE dual feeds services at the source end and selects either of the two services at the sink end. Fibers that are related to an linear MSP cannot be used by other protection subnets.

Uploaded by

Ayoub Mouhssine
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Creating 1+1 Linear MSP 1/5

Creating 1+1 Linear MSP


In a chain network, you need to create 1+1 linear MSP, to protect important services. In this way, the NE dual feeds services at the source end and selects either of the two services at the sink end.

Prerequisites
You must be an NM user with "NE and network maintainer" authority or higher. The NE data must be configured, and fibers must be properly created.

Context
Fibers that are related to an linear MSP cannot be used by other protection subnets. That is, an linear MSP and other subnets cannot create virtual fibers together. CAUTION: Starting the protocol controller may interrupt the service.

Procedure
1. Choose Configuration > Protection View from the Main Menu. In the Protection View, choose Protection View > Create SDH Protection Subnet > 1+1 linear MSP . The Wizard for Creating 1+1 Linear MSP Chain is displayed. 2. Enter the name of the protection subnet. The default name is usually used, for example, 1+1_MSP_1. 3. Select the rate of the protection subnet, for example, STM-4.

Creating 1+1 Linear MSP 2/5

4. Select the Revertive Mode and the Switching Mode as needed.

NOTE: Revertive Mode refers to the handling strategy adopted after the faulty line recovers to normal. Non-Revertive : The service does not automatically revert to the working channel after the faulty line recovers to normal. Revertive : The service automatically reverts to the working channel after the faulty line recovers to normal. Switching Mode refers to the switching strategy adopted after a

Creating 1+1 Linear MSP 3/5

fault occurs to the line. Single-ended switching : To protect services, switching occurs at the receive end when the receive end is faulty and at the transmit end when the transmit end is faulty. Dual-ended switching : To protect services, the switching occurs at the receive and transmit ends when either end is faulty. If multiple protection subnets uses one port of a board, you need to check the Resource Sharing check box. If different protection subnets use different ports of a board, do not check this check box. Select the Assigned by VC4 option when there are different VC4s belonging to different protection subnets to achieve virtual optical path protection. For example, for an STM-16 fiber, the VC4s 14 belong to an STM-4 MSP, and VC4s 58 belong to a PP. 5. Add nodes to the protection subnet to be created. Double-click the NE on the Protection View to add it to the node list in the left-hand pane. Meanwhile, is displayed on the NE icon. If you want to cancel the selection, double-click the NE again.

6. Click Next to proceed to the Select Link of the wizard. Select the Working Link and Protection Link .

Creating 1+1 Linear MSP 4/5

7. Click Finish. The created protection subnet is displayed on the Protection View.

8. Right-click the protection subnet and choose Protection Subnet Attributes from the shortcut menu. 9. Click the Protection Subnet Maintenance tab to check whether the protocol controller is started.

NOTE: If the protocol controller is not started, select all the NEs of the protection subnet. Right-click them and choose Start/Stop Protocol > Start from the shortcut menu. Click Yes in the dialog box that is displayed twice. Ensure that the status of all the values in the Protocol Controller column is Protocol Started .

Creating 1+1 Linear MSP 5/5

10.

Click the Protection Subnet Parameters tab and set the WTR time and SD condition as needed.

NOTE: The WTR time of all NEs in the same protection subnet should be the same. Parent topic: Configuring Linear MSP

Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd.

You might also like