D 0800ECT205122101 Pages: 4
Reg No.:_______________ Name:__________________________
APJ ABDUL KALAM TECHNOLOGICAL UNIVERSITY
Third Semester [Link] Degree Regular and Supplementary Examination December 2022 (2019 Scheme)
Course Code: ECT205
Course Name: NETWORK THEORY
Max. Marks: 100 Duration: 3 Hours
PART A
Answer all questions. Each question carries 3 marks Marks
1 State and explain Kirchhoff’s voltage law. (3)
2 Explain any three types of dependent or controlled sources. (3)
3 List and explain the steps involved in determining Norton’s equivalent circuit. (3)
4 State and explain maximum power transfer theorem. (3)
5 Draw the parallel and series model s-domain equivalent circuits for an (3)
inductor.
6 Determine the Laplace transform of the waveform shown in Fig. (3)
7 Classify different types of network functions and explain. (3)
8 Obtain the transfer functions Z21(S) and G21(S) for the network shown in Fig. (3)
9 Explain the reciprocity and symmetry conditions for ABCD network. (3)
10 Find the impedance parameters of a two-port network, its admittance parameter (3)
1⁄ −1⁄
is [−12 3⁄
4] .
⁄4 8
PART B
Answer any one full question from each module. Each question carries 14 marks
Module 1
11 a) Find voltage Vx using node analysis. (8)
Page 1of 4
0800ECT205122101
b) Find the current through 7V source using mesh analysis. (6)
12 a) Find voltage V1 using node analysis. (8)
b) Find the current I2 using mesh analysis. (6)
Module 2
13 a) Obtain the Thevenin equivalent network for the given network of Fig. at (7)
terminals A and B.
Find the current through the 20Ω resistor.
b) Find the value of load resistor, RL for maximum power transfer and calculate (7)
maximum power.
14 a) For the network shown in Fig., obtain Norton’s equivalent network across (7)
Page 2of 4
0800ECT205122101
terminals A and B. Find the current in the 10Ω resistor.
b) Calculate the current through the 6 Ω resistor using the superposition theorem. (7)
Module 3
15 a) Find the voltage across the capacitor, 𝑣𝑐 (𝑡) fot t > 0 in the network shown in (8)
Fig. (Assume zero initial conditions) for
1) 𝑣(𝑡) = 5𝑢(𝑡)
2) 𝑣(𝑡) = 6𝛿(𝑡)
b) Find the expression for current through a series RC circuit when a unit ramp (6)
signal is applied across it.
16 a) The switch is switched from the position ‘a’ to ‘b’ at t = 0 after steady state is (8)
achieved. Find the expression for the transient current i(t) for t>0.
b) Find the Laplace transform of the periodic function as shown in Fig. (6)
Module 4
17 a) Determine the driving-point impedance, transfer impedance and voltage (8)
transfer ratio for the network shown in the figure.
Page 3of 4
0800ECT205122101
b) Plot amplitude and phase response for the transfer function V2(s)/V1(s) of the (6)
given network.
18 a) For the given function (8)
(𝑠+2)(𝑠+4)
𝑉(𝑠) = (𝑠+1)(𝑠+5)
Find the Time domain function v(t) using the pole-zero plot (graphical method)
b) 𝑉2 (𝑠) 𝑉1 (𝑠) (6)
Determine and for the network shown in Fig.
𝑉1 (𝑠) 𝐼1 (𝑠)
Module 5
19 a) Express Y parameters in terms of Z parameters and ABCD parameters. (8)
b) Draw equivalent circuit of two port network as shown in the figure in terms of (6)
Y parameters.
20 a) Derive conditions for reciprocity and symmetry for Y parameters and h (8)
parameters.
b) Two identical sections of the network shown in Fig. are connected in series. (6)
Obtain the Z‐parameters of the combination.
*****
Page 4of 4
