K5-9100 Model Product Manual:

- 1. Pink: Speaker signal output (-)

- 2. Red: Central locking relay power supply (+)
- 3. Red/Black: trunk signal output (-)
- 4. Red: Vibration sensor power supply (+)
- 5. Brown: Turning light signal output (+)
- High frequency antenna 6. Yellow: Anti-theft relay control signal (-)
- 7. White: lock signal output (-)
- 8. Blue: door signal input (-)
- 9. White/Black: Unlock signal output (-)
- 10. Orange: Foot brake signal input (+)
- 11. Brown: Turning light signal output (+)
- 12. Purple: oil pump signal input (+)

1. Brown: ON2(+)
2. Yellow:STA(+)
3. Red: 12V(+)
4. Black: GND(-)
- LED warning light 5. Brown: ON1(+)
- Factory reset switch 6. Blue:ACC(+) (Cut off Power when starting)

-PKE induction antenna

-
- Shock sensor
- PKE induction antenna
- Engine start button

Note: !!! Strictly follow the (+) or (-) signal cable of the product to connect the positive or negative signal !!!
!!! wrong connection will lead to the positive and negative short circuit, which may not work of the product !!!
 Orange: NC, normally open
white: COM, locked
Yellow: NO, normally closed

Orange/Black: NC, Normally Open

White/Black: COM, Unlocked
Yellow/Black: NO, normally closed

Opinions on central locking processing:

The central locking unit of this system is controlled by 2 independent relays. They contain a total of 6 cables. They can be applied to almost any car. They are orange for NC, yellow for NO, and
locking and unlocking. White, please refer to the schematic diagram to use them according to the actual situation, for example, you want them to output negative signals for locking and
unlocking, then you just need to leave NC floating, not connected anywhere, and then connect NO to ground, so that white and white/ The black cable will output a negative signal for locking
and unlocking.

Function Description:
1. Push button to start /stop engine:
Turn On: step on the brake, press the start-stop button once, the engine turn on; do not step on the brake, hold down the button for 5 seconds to turn on the engine. If you press the button
forever, the engine will start forever. Turn Off: step on the brake, press the button once, the engine will turn off; do not step on the brake, hold down the button for 5 seconds to turn off
the engine.

2. Remote ignition/shutdown engine:

The module must be in the locked state, press the "trunk" button of the remote control for 3 times to start the engine remotely. After the engine starts successfully, the module will remain
 in the alert state. If you do not unlock it, the module will automatically shut down the engine when you step on the brake and emit Alarm; after the engine is successfully ignited remotely,
before you get on the car and step on the brake, you can press the "trunk" button of the remote control again to remotely turn off the engine.

3. PKE keyless entry:

Install the system correctly, connect the PKE antenna correctly, the module will be automatically unlocked when the remote control is about 1.5 meters away; the module will be automatically
locked when the remote control is about 3 meters away. If you press the "lock" button on the remote control, the PKE keyless entry will be suspended, that is, even if the remote control is
nearby, the module will not automatically unlock, press the "unlock" button on the remote control to activate the PKE keyless entry again; When the module is in the unlocked state, press
the "unlock" button on the remote control 3 times continuously, this operation can permanently turn on or off the PKE keyless entry function.

4. Arming and Disarming:

When the module is armed, the light of the engine start button is off, and the LED warning light keeps flashing. The engine cannot be started or cannot drive a car in this state, and the
module will issue an alarm when the conditions are met. When you unlock the module, the LED warning light is off, and the light of the engine start button flashes slowly or always on,
indicating that the module is disarmed, You can start the engine or drive the car.

5. Anti-hijacking, anti-robbery:
after remote start engine, If the key is not detected for more than 2 minutes when Driving, the module will alarm for 30 seconds, and then turn off the engine to enter the anti-theft; press
the "lock" button on the key, "Anti-hijacking" will be closed;press the "unlock" button on the key, "Anti-hijacking" will be opened; Note: 1. "Anti-hijacking" only works when "PKE keyless
entry" turn on; 2. "Anti-hijacking" only works after "remote start engine".

6. Set the signal output time when the trunk compartment is opened:
This operation is used to set the red/black cable and trunk signal output time. In the driving state, press and hold the "unlock" button on the remote control for 3 seconds, the horn will
sound 2 times, indicating that the signal is output for 2 seconds, continue to press and hold the "unlock" button again, the horn sounds 3 times, indicating that the signal is output for 3
seconds, the maximum setting is 4 seconds, the shortest is 1 second, and the factory default is 1 second.

7. Open ACC or ON only:

Do not step on the brakes, press the start engine button once, only turn on the ACC, press the button again and turn on ON, and press it again to turn off; Note: When only the ON is turned
on, if the brake is pressed, the button light will flash rapidly. At this time, press the button again to start the engine. We often use this method to check whether the brake signal cable is
connected correctly.

8. Lift the alarm in emergency situations:

In the state of the alarm sounding, if you cannot cancel the alarm through the remote control or APP, press and hold "Factory reset switch" for 3 seconds to cancel the alarm in an emergency,
and the engine can be started in a short time. Note: Only the owner of the car can use this action in an emergency.

9. Remote control and module matching:

When the module is disarmed, keep pressing "Factory reset switch" for 3 seconds, the module will enter the matching mode. At this time, press any button of the remote control to be
matched to complete the matching. One remote control is matched once, and the module can match up to 2 remote controls at the same time. , every time a match completes a new code,
 the module will forget the old code.

10. Set the unlock when remotely starting and then lock:
Some cars start the engine in the lock state, and the car itself will issue an alarm. If so, we can set up "Unlock When Remote Starting" to solve this problem: In the state of driving, press and
hold the "Factory Reset Switch" for 3 seconds, open the " Unlock When Remote Starting ", The horn sounds 3 times, the turning light flashs 3 times; try again, The horn sounds 1 times, the
turning light flashs 1 times, and the" unlock when remote starting "was turned off.

11. Set press the startup-stop button, open "ON" instantly:

Some car brakes will have positive signals, and "on" must be opened. If so, we can set up "ON" instantly when you press the button, In the state of driving, press "Factory reset switch" 3
times in a row, The horn sounds 3 times, the turning light flashs 3 times, opened "ON twinkling", try again, The horn sounds 1 times, the turning light flashs 1 times, and "ON twinkling" is
turned off.

12. Unlock 2 times when unlocking:

In the state of driving, press and hold the remote control "lock" key for 3 seconds, The horn sounds 2 times, the turning light flashs 2 times, open "Unlock 2 times when unlocking", try again,
The horn sounds 1 times, the turning light flashs 1 times, turn off "Unlock 2 times when unlocking".

13. Silent mode, silent alarm:

In the unlocked state, if you keep pressing the "Lock" remote control for 3 seconds, the system will lock silently and remain in silent mode until next arming. The next time you are armed, if
you short press the remote control lock button, the module will exit silent mode.

14. Autolock when Driving/Open door flashing light:

the engine starts, step on the brake, autolock the door, unlock when the engine is off; When you open the door, the turn light will flash 15 times (stop flashing when closing the
door).Note:that for security reasons,"Autolock when Driving" runs by default and cannot be turned off; "Open door flashing light" runs by default and cannot be turned off(alert the car
behind).

15. Turn on “ON” when unlocking:

Some cars need to turn on "ON" when unlocking, you can start the engine remotely, then press the remote control "unlock"-"lock"-"unlock"-“lock” continuously, the horn sounds 3 times,
the turning light flashes 3 times, and "Turn on “ON” when unlocking" turn on; Shut down the engine and try again, horn sound once, turning light flashe once, "Turn on“ON” when
unlocking" turn off.

Question & Answer:

1. Not enough time to start the engine? Or the engine has started but the ignition motor is still running for some seconds?
The purple oil pump wire must be connected, it can be connected to ON1 or ON2, the startup time is 1 second (minimum time), if nothing it is connected, the starting time is 3 seconds
(maximum time).
2. Can't start the engine remotely? Or the module automatically shuts down the engine after starting the engine remotely, and then restarts it repeatedly?
1. In the locked state, press "trunk" 3 times in a row to start the engine remotely. Make sure the operation is correct, If the car is only powered on, the engine does not start, Maybe the car
itself needs to hit the brakes to start the engine, you need to connect an extra wire to the yellow start wire of the module, and then this wire is connected with a diode (single guide), and
then connected to the brake signal wire of the car; 2. The repeated start of the engine is caused by the purple oil pump cable not being connected. If the engine start time "1 second" is
enough, you can connect this wire to "ON1" or "ON2".

3. Button can open ACC/ON, but can't start engine?

The problem is caused by the wrong connection of the brake signal cable. Press the button twice to turn on the "ON" state. At this time, press the brake and the button will flash rapidly. If
it does not flash rapidly, it means that the brake signal cable is connected incorrectly or not connected; In addition, in the disarmed state (without turning on ACC or ON), press and hold the
button for 5 seconds to start the engine without pressing the brake.

4. When only ACC is turned on, “ON” will flash once, leakage?
This is a normal situation, because some cars need to turn on "ON" then it has a brake signal, so when the button is pressed for the first time, we must turn on "ON" to detect the brake
signal, so that, Decide whether to start the engine or just turn on ACC. If you don't like it, you can turn off this feature via settings.

5. The remote control is nearby, but the module is locked and unlocked repeatedly?
If it is not frequent, it may be caused by radio interference in the surrounding environment. Pressing the lock on the key to turn off "PKE keyless entry" can avoid repeatedly locking and
unlocking, or leaving the area; If the fault occurs frequently, 1. Check whether the PKE antenna interface is broken. (Pulling the PKE antenna during installation may break the interface.) 2.
PKE antenna should not stick to the metal; 3. The battery of the remote control is insufficient. It is recommended to replace the battery. 4. Remote controls should not be placed with mobile
phones or other magnetic objects.

6. How to connect "Yellow: Anti-theft relay control signal (-)"?

After the module is armed, it will continuously output negative signal; when the module is disarmed,
it will stop outputting; this cable can be used for "BY PASS" or connect an additional relay to cut off
the circuit of the car itself, when connected correctly, the module is armed, even with the key of the
car itself Can not start the engine, please refer to the picture for the connection method of the relay.

7. Things users must know:

1. The acceptable voltage range of this system is 8-15V. Too high or too low voltage will cause the
system to not work normally;
2. All output signal cables must be connected to the correct signal according to the "+" or "-" marked
in the drawing. Wrong connection may cause the system to short-circuit and burn;
3. When the system is in the fortified state, the orange brake cable receives a positive signal, or the
blue door signal cable receives a negative signal, or the purple oil pump cable receives a positive
signal, or the shock sensor is activated, if any of the above conditions are met, the system will sound the alarm;
4. The system is in the disarmed state, if the purple oil pump cable receives a continuous positive signal, the system will enter the driving state synchronously, which can be well compatible
 with the car's original key start system.

8. Neither the remote nor the button can start the engine.
1. First check whether the cable connection of the ignition part is correct, pay special attention to the yellow starting cable and the blue ACC cable. The blue ACC cable will cut off the
power when starting and must be connected to the original cable of the car that will cut off the power when starting. It may be ACC, it may be ON, or both ACC and ON will be powered
off.
2. If you confirm that the ignition cable is connected correctly, then the inability to start the engine may be because the car itself has a chip anti-theft, and you need to let the car sense
the original anti-theft chip key.

9. It will automatically start again when started remotely.

This is caused by the purple oil pump cable not being connected. The purple oil pump cable must be connected. It can be connected to ON1 or ON2.

Remote Control Button Function:

- lock, short press once, - Trunk, press 2 times in unlocked state,

- audible anti-theft; - open the trunk;
- keep pressing for 3 seconds, - press 3 times in locked state,
- silent anti-theft. - remotely start the engine.

- Unlock, short press once, - Trunk, press 2 times in unlocked state,

- release anti-theft; - open the trunk;
- in unlocked state, - press 3 times in locked state,
- press 3 times, - remotely start the engine.
- turn off PKE keyless entry. -