Scribd
Upload
14 views2 pages

Aprime2usergu LGB

The document is a user guide for the AUTROPRIME Interactive Fire Detection System, detailing the operation of the panel and actions to take during different alarm states. It outlines steps for responding to fire alarms, pre-alarms, and faults, including silencing alarms and resetting the system. Users are instructed to follow local fire instructions and investigate scenes as necessary.

Uploaded by

vkmsd2007
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
14 views2 pages

Aprime2usergu LGB

The document is a user guide for the AUTROPRIME Interactive Fire Detection System, detailing the operation of the panel and actions to take during different alarm states. It outlines steps for responding to fire alarms, pre-alarms, and faults, including silencing alarms and resetting the system. Users are instructed to follow local fire instructions and investigate scenes as necessary.

Uploaded by

vkmsd2007
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

To operate the panel,

turn the key clock-wise

AUTROPRIME
Interactive Fire Detection System
Shortform User Guide in English

116-P-APRIME2-USERGU/LGB, 2012-01-10
Fire Alarm Fire Alarm Pre Alarm Faults
with Alarm Delay

One or several fire detectors or manual A point is sending an alarm signal A fire detector in one of the detection A fault is indicated by one of the
call points in one or several detection from a Delayed Action detection zone zones has entered the Pre Alarm state. components (fire detectors, external
zones are signalling a Fire Alarm. (alarm delay is active). equipment or other faults).

(Display Picture - Example) (Display Picture - Example) (Display Picture - Example) (Display Picture - Example)

STEP Actions to be taken - Operation Mode STEP Actions to be taken - Operation Mode STEP Actions to be taken - Operation Mode STEP Actions to be taken - Operation Mode

1 Follow all precautions described in the


local fire instructions, step by step. 1 Follow all precautions described in the
local fire instructions, step by step. 1 Follow all precautions described in the
local fire instructions, step by step. 1 Notify service/technical personnel if
necessary.

2 To silence the internal buzzer, press the


Mute Panel button 2 To silence the internal buzzer, press the
Mute Panel button 2 To silence the internal buzzer, press the
Mute Panel button 2 To silence the internal buzzer, press the
Mute Panel button

3 Scroll with the arrow down (/up) button to


observe the point(s) in fire alarm state. 3 Scroll with the arrow down (/up) button to
observe the points(s) in fire alarm state. 3 Scroll with the arrow down (/up) button to
observe the points(s) in pre alarm state. 3 Scroll with the arrow down (/up) button to
observe the point(s) in fault state.

4 To view detailed information for a


selected point, press Enter 4 To view detailed information for a
selected point, press Enter 4 To view detailed information for a
selected point, press Enter 4 To view detailed information for a
selected point, press Enter

5 Investigate the scene(s) and carry out the


necessary actions. 5 Investigate the scene(s) and carry out the
necessary actions. 5 Investigate the scene(s) and carry out the
necessary actions. 5 Investigate the scene(s) and carry out the
necessary actions.

6 To silence all alarms, press the Silence


Alarms button 6 To Prolong the alarm delay, if necessary,
press the Prolong Delay button 6 To acknowledge a Pre Alarm, press the
red Silence button 6 To acknowledge the fault(s), move back
one level using the Cancel button.

7 Press the Reset button 7 If there is not a fire, the procedure can
be ended by pressing the green Reset 7 Press the Reset button 7 Scroll to select the desired point, press
the Function button , then select
button Acknowledge to acknowledge the
selected fault or Acknowledge all to
If there really is a fire, press the Activate acknowledge all faults.
Outputs button or activate the nearest
manual call-point to activate alarm, carry
out the necessary measures, then go to 8 Press the Reset button

step 8.

8 To silence all alarms, press the Silence


Alarms button

9 Press the Reset button

You might also like