Scribd
Upload
6 views2 pages

Mcpc Mid 2023

The document outlines the examination structure for the M.Tech. Mid Semester (Spring) Examination 2023 for the subject 'Modeling and Control of Power Converters' at the National Institute of Technology, Rourkela. It includes questions on deriving voltage relationships, analyzing waveforms, and evaluating circuit parameters for various power converter configurations. The examination consists of multiple questions requiring calculations, sketches, and derivations related to power converters.

Uploaded by

soumyajeet1998
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
6 views2 pages

Mcpc Mid 2023

The document outlines the examination structure for the M.Tech. Mid Semester (Spring) Examination 2023 for the subject 'Modeling and Control of Power Converters' at the National Institute of Technology, Rourkela. It includes questions on deriving voltage relationships, analyzing waveforms, and evaluating circuit parameters for various power converter configurations. The examination consists of multiple questions requiring calculations, sketches, and derivations related to power converters.

Uploaded by

soumyajeet1998
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

NATIONAL INSTITUTE OF TECHNOLOGY, ROURKELA-8

M.Tech. Mid Semester (Spring) Examination, 2023


SUBJECT: Modeling and Control of Power Converters CODE: EE-6330
Duration of Examination: 2 hours FULL MARKS: 30
Figures at the right hand margin indicate marks. All parts of a question should be
answered at one place. Assume any missing information appropriately.
Answer all Questions
Q1. Referring to the converter circuit shown in Fig (a), answer the following questions,
i) Derive the steady state input output voltage relationship (i.e. duty ratio) for each
case for the switch drive signal given in Fig b), c) and d) using volt-sec balance.
Find the output voltage in each case. [2+2+2=6]
ii) Sketch the steady-state waveform of iL and voltage stresses on switch Q1 and Q2 for
each case. Label the maximum and minimum values on your sketch. [4]
iL 50  H

Q1
Q2 Vo 5
20V C

(a)
Closed Closed
Q1 Closed
Open Q1
10  s Q1 Open Closed
20  s
Open Q2 Open
Q2 Q2

(b) (c) (d)


Q2. a) Shown in the below figure is the circuit diagram of a buck converter and its
inductor current waveform.
iL L

VL
Rc Vo R
12V
2500  F

4.5A

iL
60 s 20  s 20 s
i) Find values for the inductance L and resistance R.
ii) Sketch the capacitor current iC . Show the maximum and minimum values.
iii) Evaluate vo when Rc = 0 . [3+2+1=6]
b) Derive the rms expressions for the switch current of the buck converter. [4]

Q3. a) Consider the half-bridge converter shown in figure below along with its switch
drive signals.
is

100  F Q1
1: 2 300 H
200V iL
20
100  F iD 3
Q2 470  F v0

Closed
Q1 20  s Open
100 s

Closed
Q2 Open
20  s
50  s

i) Find the average value of the output voltage vo .


ii) Referring to the switch drive signals, sketch iL , and iD 3 . Show the maximum,
minimum and average values on your sketch. [2+4=6]

b) In the boost converter, consider that the inductor has the resistance rL . All other losses
can be neglected. [2+2=4]
i) Derive a complete equivalent circuit model for this converter.
ii) Solve your model to find the output voltage.

You might also like