Microset 121S and Microset 121F Forming Putty Part B Version number: 5

Date: 24.06.2016
Supercedes: 28.10.2012

SAFETY DATA SHEET

Microset 121S and Microset 121F
Forming Putty Part B

This Safety Data Sheet contains information concerning the potential risks to those involved in handling,
transporting and working with the material, as well as describing potential risks to the consumer and the
environment. This information must be made available to those who may come into contact with the material or
are responsible for the use of the material. This Safety Data Sheet is provided voluntarily and is prepared in
accordance with formatting described in the REACH Regulation (EC) No 1907/2006, and described in CLP
Regulation (EC) No 1272/2008.

SECTION 1: Identification of the substance/mixture and of the company/undertaking

1.1 Product identifier

Product name: Microset 121S and Microset 121F Forming Putty Part B

1.2 Relevant identified uses of the substance or mixture and uses advised against
Two Component Silicone Rubber Compound.

1.3 Details of the supplier of the safety data sheet

Microset Products Ltd,
Unit 1 Marina Court, Tungsten Park,
Maple Drive,
Hinckley, Leicestershire,
LE10 3BF, UK
Phone: +44 (0)1455 634508
Fax: +44(0) 1455 613287
Email: [email protected]

1.4 Emergency telephone number

In case of emergency Tel. +44 (0)1455 634508 (8.30am – 5.30pm, Monday to Friday)

SECTION 2: Hazards Identification

2.1 Classification of the substance or mixture

Not classified as hazardous according to the CLP Regulation (EC) No 1272/2008

2.2 Label elements

No label required according to the CLP Regulation (EC) No 1272/2008

2.3 Other hazards

Physical hazards: Not classified as flammable, but will burn if involved in a fire.
Health hazards: No specific symptoms noted by any route of exposure.
Environmental hazards: Not regarded as dangerous for the environment. None of the components
are known to be PBT/vPvB.

SECTION 3: Composition

3.1 Substances
Not applicable, the product is a mixture.

Page 1 of 6
Microset 121S and Microset 121F Forming Putty Part B Version number: 5
Date: 24.06.2016
Supercedes: 28.10.2012

3.2 Mixtures
Organopolysiloxane mixture
Crystalline silica (SiO2)is embedded in the product and not available as respirable dusts. When used
as intended or as supplied, the product will not pose hazards of Crystalline silica.

SECTION 4: First Aid Measures

4.1 Description of first aid measures

EYE CONTACT: Wash thoroughly with water and obtain medical attention if signs of discomfort.
INHALATION: Remove from exposure. If breathing becomes difficult call a doctor.
SKIN CONTACT: Wash off with soap and water. Seek medical attention.
INGESTION: If swallowed, rinse mouth with water.

4.2 Most important symptoms and effects, both acute and delayed
No specific symptoms identified

4.3 Indication of any immediate medical attention and special treatments needed
Symptomatic treatment as required

SECTION 5: Firefighting Measures

5.1 Extinguishing media

Suitable extinguishing media: Water spray, Foam. Powder. Carbon dioxide (CO2).
Unsuitable extinguishing media: None identified

5.2 Special hazards arising from the substance or mixture

Will burn if involved in a fire. Use water spray to cool containers. Keep containers cool. Thermal
breakdown of this product during fire or very high heat condition may evolve the following hazardous
decomposition product: Carbon oxides and traces of Incompletely burned carbon compounds. Silicon
dioxide. Formaldehyde.
Prevent run-off from fire from entering water courses and sewers.

5.3 Advice for fire fighters

Self-contained breathing apparatus and thermal protective clothing must be worn in case of fire

SECTION 6: Accidental Release Measures

6.1 Personal precautions, protective equipment and emergency procedures

Remove ignition sources. Wear suitable protective clothing including gloves and eye protection to avoid
unnecessary skin or eye contact. Spillages may be slippery.

6.2 Environmental precautions

Prevent entry into sewers and watercourses. If large quantities of product enters sewers or
watercourses, inform the appropriate environmental authorities.

6.3 Methods and materials for containment and clearing up

Small spills: Scrape up with cardboard or paper towels and place in a suitable container for disposal.
Wash the spill area with detergent and water.

Large spills: Mix spillage with a suitable non-combustible absorbent, e.g. sand or earth, and scrape up
and place in a suitable container for disposal. Wash the spill area with detergent and water.

Contaminated material may release hydrogen gas. Containers with collected spillage must be properly
labelled with correct contents.

6.4 References to other sections

See section 8 for further advice on PPE and section 13 for further advice on disposal.

Page 2 of 6
Microset 121S and Microset 121F Forming Putty Part B Version number: 5
Date: 24.06.2016
Supercedes: 28.10.2012

SECTION 7: Handling and Storage

7.1 Precautions for safe handling

Avoid contact with skin and eyes. Use in well ventilated areas. Keep containers closed when not in use.

7.2 Conditions for safe storage, including any incompatibilities

Store in a cool, dry place with adequate ventilation. Do not lay containers on their sides. Keep away
from incompatible materials, open flames, and high temperatures. Store in closed original container.

7.3 Specific end uses(s)

No specific industry guidelines available.

SECTION 8. Exposure Controls/Personal Protection

8.1 Control parameters

Components CAS-No. Value type (Form of Control parameters Basis

exposure)
Silica, respirable crystalline TWA 0.1 mg/m3 EH40 WEL

8.2 Exposure controls

Engineering controls
Not normally required.

Respiratory protection
Not normally required.

Hand Protection
Plastic film gloves may be suitable, but manufacturer recommendations should always be consulted.
Change gloves in accordance with manufacturer recommendations. If gloves are damaged during use,
remove immediately and wash hands before replacing with new gloves.

Eye protection
Not normally required, but if contact with eyes is likely wear suitable eye protection to protect from
splashes, meeting the requirements of BS EN166 3, when handling this product.

Skin protection
Aprons or coveralls are recommended. These should be changed after use or if contaminated. Wash
before re-use.

Environmental Exposure Controls

Take suitable measures to prevent entry into drains, sewers and watercourses.

SECTION 9: Physical and Chemical Properties

9.1 Information on basic physical and chemical properties

Appearance: Yellow putty
Odour: Slight
Odour threshold: Not available
pH: Not applicable
Melting point: Not available
Boiling point: Not available
Flashpoint: > 100 °C (Closed cup)
Evaporation rate: Neglible
Flammability: Not applicable
Upper/lower flammability limits: Not available
Vapour pressure: Negligible
Vapour density: Not applicable
Page 3 of 6
Microset 121S and Microset 121F Forming Putty Part B Version number: 5
Date: 24.06.2016
Supercedes: 28.10.2012

Relative density: Approximately 1.80 (25 °C)

Solubility in water: Not soluble
Solubility in other solvents: Not available
Partition coefficient (log Kow): Not available
Autoignition temperature: Not available
Decomposition temperature: > Not available
Viscosity: Not available
Explosive properties: Contains no components classified as explosive
Oxidising properties: Contains no components classified as oxidising

9.2 Other information

None available

SECTION 10: Stability and Reactivity

10.1 Reactivity
Not considered to be a reactive material

10.2 Chemical stability

Stable under normal conditions of use and storage

10.3 Possibility of hazardous reactions

Hazardous polymerisation will not occur.

10.4 Conditions to avoid

None noted.

10.5 Incompatible materials

Strong oxidizing agents. Acidic and basic products.

10.6 Hazardous decomposition products

Thermal breakdown of this product during fire or very high heat condition may evolve the following
hazardous decomposition product: Carbon oxides and traces of Incompletely burned carbon
compounds. Silicon dioxide. Formaldehyde.

SECTION 11: Toxicological Information

11.1 Information on toxicological effects

This product has not been tested. Judgements on the expected toxicity of this product have been made based
upon consideration of its major components.

(a) acute toxicity No effects expected (assessment based on ingredients).

(b) skin corrosion/irritation No effects expected (assessment based on ingredients).
(c) serious eye damage/irritation May cause slight, transient eye irritation (assessment based on
ingredients).
(d) respiratory/skin sensitisation No effects expected (assessment based on ingredients).
(e) germ cell mutagenicity No effects expected (assessment based on ingredients).
(f) carcinogenicity No effects expected (assessment based on ingredients). Contains crystalline
silica which may cause silicosis and is considered to be a carcinogen by some
jurisdictions. The crystalline silica in this product is not available for inhalation
however under normal expected conditions of use.
(g) reproductive toxicity No effects expected (assessment based on ingredients).
(h) STOT-single exposure No effects expected (assessment based on ingredients).
(i) STOT-repeated exposure No effects expected (assessment based on ingredients).
(j) aspiration hazard No effects expected (assessment based on ingredients).

Page 4 of 6
Microset 121S and Microset 121F Forming Putty Part B Version number: 5
Date: 24.06.2016
Supercedes: 28.10.2012

SECTION 12: Ecological Information

12.1 Toxicity
No effects expected on aquatic organisms (assessment based on ingredients).

12.2 Persistence and degradability

The organic components in this product are expected to degrade very slowly.

12.3 Bioaccumulative potential

The polymer substances and inorganic materials in this product are not expected to bioaccumulate

12.4 Mobility in soil

Once cured, this product is not expected to be mobile in the environment.

12.5 Results of PBT and vPvB assessment

None of the components are known to be PBT or vPvB.

12.6 Other adverse effects

None known.

SECTION 13: Disposal Considerations

13.1 Waste treatment methods

Dispose of waste at an appropriate treatment and disposal facility in accordance with applicable laws
and regulations, and product characteristics at time of disposal. Incinerate in suitable combustion
chamber is suggested.

Contaminated packages should be as empty as possible. Do not cut or puncture containers. Dispose of
waste at an appropriate treatment and disposal facility in accordance with applicable laws and
regulations, and product characteristics at time of disposal. Recycle following cleaning or dispose of at
an authorised site.

SECTION 14: Transport Information

Not classified as dangerous goods

ADR IMDG ICAO

14.1 UN Number None None None
14.2 UN Proper shipping None None None
name
14.3 Transport hazard None None None
class(es)
14.4 Packing group None None None
14.5 Environmental None None None
hazards
14.6 Special precautions None None None
for user
14.7 Transport in bulk Not applicable Not applicable Not applicable
according to Annex II of
MARPOL 73/78 and the
IBC Code

SECTION 15: Regulatory Information

15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture
Inventory Status
EU EINECS List: On or in compliance with the inventory

15.2 Chemical Safety Assessment

A Chemical Safety Assessment has not been carried out for this product.
Page 5 of 6
Microset 121S and Microset 121F Forming Putty Part B Version number: 5
Date: 24.06.2016
Supercedes: 28.10.2012

SECTION 16: Other Information

Revision information: Reformatted in compliance with Regulation (EC) No 1907/2006, as amended by

Regulation (EU) 2015/830

List of Abbreviations used in this SDS:

CAS Chemical Abstracts Service
CLP Classification, Labelling and Packaging Regulation (EC) no 1272/2008
DSD Dangerous Substances Directive 67/548/EEC
DPD Dangerous Preparations Directive 1999/45/EC
EC European Community/Commission
PBT Persistent, Bioaccumulative and Toxic
REACH Registration, Evaluation, Authorisation and Restriction of Chemicals Regulation (EC) no 1907/2006
vPvB very Persistent, very Bioaccumulative

References:
ECHA CHEM database
Suppliers’ SDSs for component substances

Method used for classification of mixtures:

Ingredient based approaches

H Statements used in Section 3

None

Training requirements for workers

No special requirements

Page 6 of 6