74HC373; 74HCT373

Octal D-type transparent latch; 3-state

Rev. 8 — 6 September 2021 Product data sheet

1. General description
The 74HC373; 74HCT373 is an octal D-type transparent latch with 3-state outputs. The device
features latch enable (LE) and output enable (OE) inputs. When LE is HIGH, data at the inputs
enter the latches. In this condition the latches are transparent, a latch output will change each time
its corresponding D-input changes. When LE is LOW the latches store the information that was
present at the inputs a set-up time preceding the HIGH-to-LOW transition of LE. A HIGH on OE
causes the outputs to assume a high-impedance OFF-state. Operation of the OE input does not
affect the state of the latches. Inputs include clamp diodes. This enables the use of current limiting
resistors to interface inputs to voltages in excess of VCC.

2. Features and benefits

• Wide supply voltage range from 2.0 V to 6.0 V
• CMOS low power dissipation
• High noise immunity
• Latch-up performance exceeds 100 mA per JESD 78 Class II Level B
• Complies with JEDEC standards:
• JESD8C (2.7 V to 3.6 V)
• JESD7A (2.0 V to 6.0 V)
• Input levels:
• For 74HC373: CMOS level
• For 74HCT373: TTL level
• 3-state non-inverting outputs for bus oriented applications
• Common 3-state output enable input
• ESD protection:
• HBM JESD22-A114F exceeds 2000 V
• MM JESD22-A115-A exceeds 200 V
• Multiple package options
• Specified from -40 °C to +85 °C and from -40 °C to +125 °C

3. Ordering information
Table 1. Ordering information
Type number Package
Temperature range Name Description Version
74HC373D -40 °C to +125 °C SO20 plastic small outline package; 20 leads; SOT163-1
74HCT373D body width 7.5 mm

74HC373PW -40 °C to +125 °C TSSOP20 plastic thin shrink small outline package; 20 leads; SOT360-1
74HCT373PW body width 4.4 mm

74HC373BQ -40 °C to +125 °C DHVQFN20 plastic dual in-line compatible thermal enhanced SOT764-1
74HCT373BQ very thin quad flat package; no leads; 20 terminals;
body 2.5 × 4.5 × 0.85 mm
Nexperia 74HC373; 74HCT373
Octal D-type transparent latch; 3-state

4. Functional diagram

D0 Q0
3 2
D1 Q1
4 5
D2 Q2
7 6
D3 Q3
8 LATCH 3-STATE 9
D4 Q4
13 1 TO 8 OUTPUTS 12
D5 Q5
14 15
D6 Q6
17 16
D7 Q7
18 19
LE
11
OE
1
001aae050

Fig. 1. Functional diagram

1
OE EN
11 C1
LE

11
3 2
LE D0 1D Q0
3 2
D0 Q0 4 5
4 5 D1 Q1
D1 Q1
7 6 7 6
D2 Q2 D2 Q2
8 9 8 9
D3 Q3 D3 Q3
13 12 13 12
D4 Q4 D4 Q4
14 15
D5 Q5 14 15
D5 Q5
17 16
D6 Q6 17 16
18 19 D6 Q6
D7 Q7
OE 18 19
D7 Q7
1 001aae048 001aae049

Fig. 2. Logic symbol Fig. 3. IEC logic symbol

LE

LE

LE
D Q

LE 001aae051

Fig. 4. Logic diagram (one latch)

74HC_HCT373 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved

Product data sheet Rev. 8 — 6 September 2021 2 / 16

Nexperia 74HC373; 74HCT373
Octal D-type transparent latch; 3-state

D0 D1 D2 D3 D4 D5 D6 D7

D Q D Q D Q D Q D Q D Q D Q D Q
LATCH LATCH LATCH LATCH LATCH LATCH LATCH LATCH
1 2 3 4 5 6 7 8

LE LE LE LE LE LE LE LE LE LE LE LE LE LE LE LE

LE

OE

Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7
001aae052

Fig. 5. Logic diagram

5. Pinning information

5.1. Pinning

74HC373
74HCT373

20 VCC
terminal 1
OE

index area
1

Q0 2 19 Q7

D0 3 18 D7
74HC373
D1 4 17 D6
74HCT373
Q1 5 16 Q6
OE 1 20 VCC Q2 6 15 Q5
Q0 2 19 Q7
D2 7 14 D5
D0 3 18 D7 GND(1)
D3 8 13 D4
D1 4 17 D6
Q1 5 16 Q6 Q3 9 12 Q4
GND 10

LE 11

Q2 6 15 Q5
D2 7 14 D5 001aae047
D3 8 13 D4
Transparent top view
Q3 9 12 Q4
GND 10 11 LE (1) This is not a ground pin. There is no electrical or
mechanical requirement to solder the pad. In case
001aae046 soldered, the solder land should remain floating or
connected to GND.
Fig. 6. Pin configuration SOT163-1 (SO20) and
SOT360-1 (TSSOP20) Fig. 7. Pin configuration SOT764-1 (DHVQFN20)

74HC_HCT373 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved

Product data sheet Rev. 8 — 6 September 2021 3 / 16

Nexperia 74HC373; 74HCT373
Octal D-type transparent latch; 3-state

5.2. Pin description

Table 2. Pin description
Symbol Pin Description
OE 1 3-state output enable input (active LOW)
Q0, Q1, Q2, Q3, Q4, Q5, Q6, Q7 2, 5, 6, 9, 12, 15, 16, 19 3-state latch output
D0, D1, D2, D3, D4, D5, D6, D7 3, 4, 7, 8, 13, 14, 17, 18 data input
GND 10 ground (0 V)
LE 11 latch enable input (active HIGH)
VCC 20 supply voltage

6. Functional description
Table 3. Functional description
H = HIGH voltage level; h = HIGH voltage level one set-up time prior to the HIGH-to-LOW LE transition;
L = LOW voltage level; I = LOW voltage level one set-up time prior to the HIGH-to-LOW LE transition;
X = don’t care; Z = high-impedance OFF-state.
Operating mode Control Input Internal latches Output
OE LE Dn Qn
Enable and read register L H L L L
(transparent mode) H H H
Latch and read register L L l L L
h H H
Latch register and disable H X X X Z
outputs

7. Limiting values
Table 4. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol Parameter Conditions Min Max Unit
VCC supply voltage -0.5 +7 V
IIK input clamping current VI < -0.5 V or VI > VCC + 0.5 V - ±20 mA
IOK output clamping current VO < -0.5 V or VO > VCC + 0.5 V - ±20 mA
IO output current VO = -0.5 V to (VCC + 0.5 V) - ±35 mA
ICC supply current - +70 mA
IGND ground current - -70 mA
Tstg storage temperature -65 +150 °C
Ptot total power dissipation [1] - 500 mW

[1] For SOT163-1 (SO20) package: Ptot derates linearly with 12.3 mW/K above 109 °C.
For SOT360-1 (TSSOP20) package: Ptot derates linearly with 10.0 mW/K above 100 °C.
For SOT764-1 (DHVQFN20) package: Ptot derates linearly with 12.9 mW/K above 111 °C.

74HC_HCT373 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved

Product data sheet Rev. 8 — 6 September 2021 4 / 16

Nexperia 74HC373; 74HCT373
Octal D-type transparent latch; 3-state

8. Recommended operating conditions

Table 5. Recommended operating conditions
Voltages are referenced to GND (ground = 0 V)
Symbol Parameter Conditions 74HC373 74HCT373 Unit
Min Typ Max Min Typ Max
VCC supply voltage 2.0 5.0 6.0 4.5 5.0 5.5 V
VI input voltage 0 - VCC 0 - VCC V
VO output voltage 0 - VCC 0 - VCC V
Tamb ambient temperature -40 +25 +125 -40 +25 +125 °C
Δt/ΔV input transition rise and fall rate VCC = 2.0 V - - 625 - - - ns/V
VCC = 4.5 V - 1.67 139 - 1.67 139 ns/V
VCC = 6.0 V - - 83 - - - ns/V

9. Static characteristics
Table 6. Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter Conditions Tamb = 25 °C Tamb = -40 °C Tamb = -40 °C Unit
to 85 °C to 125 °C
Min Typ Max Min Max Min Max
74HC373
VIH HIGH-level input VCC = 2.0 V 1.5 1.2 - 1.5 - 1.5 - V
voltage VCC = 4.5 V 3.15 2.4 - 3.15 - 3.15 - V
VCC = 6.0 V 4.2 3.2 - 4.2 - 4.2 - V
VIL LOW-level input VCC = 2.0 V - 0.8 0.5 - 0.5 - 0.5 V
voltage VCC = 4.5 V - 2.1 1.35 - 1.35 - 1.35 V
VCC = 6.0 V - 2.8 1.8 - 1.8 - 1.8 V
VOH HIGH-level output VI = VIH or VIL - - -
voltage IO = -20 μA; VCC = 2.0 V 1.9 2.0 - 1.9 - 1.9 - V
IO = -20 μA; VCC = 4.5 V 4.4 4.5 - 4.4 - 4.4 - V
IO = -20 μA; VCC = 6.0 V 5.9 6.0 - 5.9 - 5.9 - V
IO = -6.0 mA; VCC = 4.5 V 3.98 4.32 - 3.84 - 3.7 - V
IO = -7.8 mA; VCC = 6.0 V 5.48 5.81 - 5.34 - 5.2 - V
VOL LOW-level output VI = VIH or VIL
voltage IO = 20 μA; VCC = 2.0 V - 0 0.1 - 0.1 - 0.1 V
IO = 20 μA; VCC = 4.5 V - 0 0.1 - 0.1 - 0.1 V
IO = 20 μA; VCC = 6.0 V - 0 0.1 - 0.1 - 0.1 V
IO = 6.0 mA; VCC = 4.5 V - 0.15 0.26 - 0.33 - 0.4 V
IO = 7.8 mA; VCC = 6.0 V - 0.16 0.26 - 0.33 - 0.4 V
II input leakage VI = VCC or GND; VCC = 6.0 V - - ±0.1 - ±1.0 - ±1.0 μA
current
IOZ OFF-state output VI = VIH or VIL; VCC = 6.0 V; - - ±0.5 - ±5.0 - ±10.0 μA
current VO = VCC or GND
ICC supply current VCC = 6.0 V; IO = 0 A; - - 8.0 - 80 - 160 μA
VI = VCC or GND

74HC_HCT373 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved

Product data sheet Rev. 8 — 6 September 2021 5 / 16

Nexperia 74HC373; 74HCT373
Octal D-type transparent latch; 3-state

Symbol Parameter Conditions Tamb = 25 °C Tamb = -40 °C Tamb = -40 °C Unit

to 85 °C to 125 °C
Min Typ Max Min Max Min Max
CI input capacitance - 3.5 - - - - - pF
74HCT373
VIH HIGH-level input VCC = 4.5 V to 5.5 V 2.0 1.6 - 2.0 - 2.0 - V
voltage
VIL LOW-level input VCC = 4.5 V to 5.5 V - 1.2 0.8 - 0.8 - 0.8 V
voltage
VOH HIGH-level output VI = VIH or VIL
voltage IO = -20 μA; VCC = 4.5 V 4.4 4.5 - 4.4 - 4.4 - V
IO = -6.0 mA; VCC = 4.5 V 3.98 4.32 - 3.84 - 3.7 - V
VOL LOW-level output VI = VIH or VIL
voltage IO = 20 μA; VCC = 4.5 V - 0.0 0.1 - 0.1 - 0.1 V
IO = 6.0 mA; VCC = 4.5 V - 0.16 0.26 - 0.33 - 0.4 V
II input leakage VI = VCC or GND; VCC = 5.5 V - - ±0.1 - ±1.0 - ±1.0 μA
current
IOZ OFF-state output VI = VIH or VIL; VCC = 5.5 V; - - ±0.5 - ±5.0 - ±10 μA
current VO = VCC or GND
ICC supply current VI = VCC or GND; IO = 0 A; - - 8.0 - 80 - 160 μA
VCC = 5.5 V
ΔICC additional supply VI = VCC - 2.1 V;
current other inputs at VCC or GND;
VCC = 4.5 V to 5.5 V; IO = 0 A
Dn - 30 108 - 135 - 147 μA
LE - 150 540 - 675 - 735 μA
OE - 100 360 - 450 - 490 μA
CI input capacitance - 3.5 - - - - - pF

10. Dynamic characteristics

Table 7. Dynamic characteristics
Voltages are referenced to GND (ground = 0 V); CL = 50 pF unless otherwise specified; for test circuit see Fig. 12.
Symbol Parameter Conditions Tamb = 25 °C Tamb = -40 °C Tamb = -40 °C Unit
to +85 °C to +125 °C
Min Typ Max Min Max Min Max
74HC373
tpd propagation Dn to Qn; see Fig. 8 [1]
delay VCC = 2.0 V - 41 150 - 190 - 225 ns
VCC = 4.5 V - 15 30 - 38 - 45 ns
VCC = 5 V; CL = 15 pF - 12 - - - - - ns
VCC = 6.0 V - 12 26 - 33 - 38 ns
LE to Qn; see Fig. 9
VCC = 2.0 V - 50 175 - 220 - 265 ns
VCC = 4.5 V - 18 35 - 44 - 53 ns
VCC = 5 V; CL = 15 pF - 15 - - - - - ns
VCC = 6.0 V - 14 30 - 37 - 45 ns

74HC_HCT373 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved

Product data sheet Rev. 8 — 6 September 2021 6 / 16

Nexperia 74HC373; 74HCT373
Octal D-type transparent latch; 3-state

Symbol Parameter Conditions Tamb = 25 °C Tamb = -40 °C Tamb = -40 °C Unit

to +85 °C to +125 °C
Min Typ Max Min Max Min Max
ten enable time OE to Qn; see Fig. 10 [2]
VCC = 2.0 V - 44 150 - 190 - 225 ns
VCC = 4.5 V - 16 30 - 38 - 45 ns
VCC = 6.0 V - 13 26 - 33 - 38 ns
tdis disable time OE to Qn; see Fig. 10 [3]
VCC = 2.0 V - 47 150 - 190 - 225 ns
VCC = 4.5 V - 17 30 - 38 - 45 ns
VCC = 6.0 V - 14 26 - 33 - 38 ns
tt transition time Qn; see Fig. 8 and Fig. 9 [4]
VCC = 2.0 V - 14 60 - 75 - 90 ns
VCC = 4.5 V - 5 12 - 15 - 18 ns
VCC = 6.0 V - 4 10 - 13 - 15 ns
tW pulse width LE HIGH; see Fig. 9
VCC = 2.0 V 80 17 - 100 - 120 - ns
VCC = 4.5 V 16 6 - 20 - 24 - ns
VCC = 6.0 V 14 5 - 17 - 20 - ns
tsu set-up time Dn to LE; see Fig. 11
VCC = 2.0 V 50 14 - 65 - 75 - ns
VCC = 4.5 V 10 5 - 13 - 15 - ns
VCC = 6.0 V 9 4 - 11 - 13 - ns
th hold time Dn to LE; see Fig. 11
VCC = 2.0 V +5 -8 - 5 - 5 - ns
VCC = 4.5 V +5 -3 - 5 - 5 - ns
VCC = 6.0 V +5 -2 - 5 - 5 - ns
CPD power dissipation per latch; VI = GND to VCC [5] - 45 - - - - - pF
capacitance
74HCT373
tpd propagation Dn to Qn; see Fig. 8 [1]
delay VCC = 4.5 V - 17 30 - 38 - 45 ns
VCC = 5 V; CL = 15 pF - 14 - - - - - ns
LE to Qn; see Fig. 9
VCC = 4.5 V - 16 32 - 40 - 48 ns
VCC = 5 V; CL = 15 pF - 13 - - - - - ns
ten enable time OE to Qn; VCC = 4.5 V; [2] - 19 32 - 40 - 48 ns
see Fig. 10
tdis disable time OE to Qn; VCC = 4.5 V; [3] - 18 30 - 38 - 45 ns
see Fig. 10
tt transition time Qn; VCC = 4.5 V; [4] - 5 12 - 15 - 18 ns
see Fig. 8 and Fig. 9

74HC_HCT373 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved

Product data sheet Rev. 8 — 6 September 2021 7 / 16

Nexperia 74HC373; 74HCT373
Octal D-type transparent latch; 3-state

Symbol Parameter Conditions Tamb = 25 °C Tamb = -40 °C Tamb = -40 °C Unit

to +85 °C to +125 °C
Min Typ Max Min Max Min Max
tW pulse width LE HIGH; VCC = 4.5 V; 16 4 - 20 - 24 - ns
see Fig. 9
tsu set-up time Dn to LE; VCC = 4.5 V; 12 6 - 15 - 18 - ns
see Fig. 11
th hold time Dn to LE; VCC = 4.5 V; 4 -1 - 4 - 4 - ns
see Fig. 11
CPD power dissipation per latch; [5] - 41 - - - - - pF
capacitance VI = GND to (VCC - 1.5 V)

[1] tpd is the same as tPLH and tPHL.

[2] ten is the same as tPZH and tPZL.
[3] tdis is the same as tPLZ and tPHZ.
[4] tt is the same as tTHL and tTLH.
[5] CPD is used to determine the dynamic power dissipation (PD in μW).
2 2
PD = CPD × VCC × fi × N + Σ(CL × VCC × fo) where:
fi = input frequency in MHz;
fo = output frequency in MHz;
CL = output load capacitance in pF;
VCC = supply voltage in V;
N = number of inputs switching;
2
Σ(CL × VCC × fo) = sum of outputs.

10.1. Waveforms and test circuit

Dn input VM

t PLH t PHL

90 %
Qn output VM
10 %
t TLH t THL
001aae082

Measurement points are given in Table 8.

Fig. 8. Propagation delay input (Dn) to output (Qn) and transition time output (Qn)

LE input VM

tW
t PHL t PLH

90 %
Qn output VM
10 %
t THL t TLH
001aae083

Measurement points are given in Table 8.

Fig. 9. Pulse width latch enable input (LE), propagation delay (LE) to output (Qn) and transition time output (Qn)

74HC_HCT373 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved

Product data sheet Rev. 8 — 6 September 2021 8 / 16

Nexperia 74HC373; 74HCT373
Octal D-type transparent latch; 3-state

VI

OE input VM

GND
tPLZ tPZL
VCC
output
LOW-to-OFF VM
OFF-to-LOW
10%
VOL
tPHZ tPZH
VOH
90%
output
HIGH-to-OFF VM
OFF-to-HIGH
GND
outputs outputs outputs
enabled disabled enabled
001aae307

Measurement points are given in Table 8.

Fig. 10. 3-state enable and disable time

LE input VM

t su t su
th th

Dn input VM

001aae084

Measurement points are given in Table 8.

Fig. 11. Set-up and hold time data input (Dn) to latch enable input (LE)

Table 8. Measurement points

Type Input Output
VM VM
74HC373 0.5VCC 0.5VCC
74HCT373 1.3 V 1.3 V

74HC_HCT373 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved

Product data sheet Rev. 8 — 6 September 2021 9 / 16

Nexperia 74HC373; 74HCT373
Octal D-type transparent latch; 3-state

tW
VI
90 %
negative
pulse VM VM
10 %
0V
tf tr

tr tf
VI
90 %
positive
pulse VM VM
10 %
0V
tW

VCC VCC

VI VO RL S1
G DUT open

RT CL

001aad983

Test data is given in Table 9.

Definitions test circuit:
RT = Termination resistance should be equal to output impedance Zo of the pulse generator
CL = Load capacitance including jig and probe capacitance
RL = Load resistor
S1 = Test selection switch
Fig. 12. Test circuit for measuring switching times

Table 9. Test data

Type Input Load S1 position
VI tr, tf CL RL tPHL, tPLH tPZH, tPHZ tPZL, tPLZ
74HC373 VCC 6 ns 15 pF, 50 pF 1 kΩ open GND VCC
74HCT373 3V 6 ns 15 pF, 50 pF 1 kΩ open GND VCC

74HC_HCT373 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved

Product data sheet Rev. 8 — 6 September 2021 10 / 16

Nexperia 74HC373; 74HCT373
Octal D-type transparent latch; 3-state

11. Package outline

SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1

D E A
X

c
y HE v M A

20 11

Q
A2 A
A1 (A 3 )

pin 1 index
θ
Lp
L

1 10 detail X
e w M
bp

0 5 10 mm
scale

DIMENSIONS (inch dimensions are derived from the original mm dimensions)

A
UNIT A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y Z
(1)
θ
max.
0.3 2.45 0.49 0.32 13.0 7.6 10.65 1.1 1.1 0.9
mm 2.65 0.25 1.27 1.4 0.25 0.25 0.1
0.1 2.25 0.36 0.23 12.6 7.4 10.00 0.4 1.0 0.4 8
o
o
0.012 0.096 0.019 0.013 0.51 0.30 0.419 0.043 0.043 0.035 0
inches 0.1 0.01 0.05 0.055 0.01 0.01 0.004
0.004 0.089 0.014 0.009 0.49 0.29 0.394 0.016 0.039 0.016

Note
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.

OUTLINE REFERENCES EUROPEAN

ISSUE DATE
VERSION IEC JEDEC JEITA PROJECTION

99-12-27
SOT163-1 075E04 MS-013
03-02-19

Fig. 13. Package outline SOT163-1 (SO20)

74HC_HCT373 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved

Product data sheet Rev. 8 — 6 September 2021 11 / 16

Nexperia 74HC373; 74HCT373
Octal D-type transparent latch; 3-state

TSSOP20: plastic thin shrink small outline package; 20 leads; body width 4.4 mm SOT360-1

D E A
X

y HE v M A

20 11

Q
A2 (A 3 ) A
A1
pin 1 index

θ
Lp
L
1 10
detail X
w M
e bp

0 2.5 5 mm
scale

DIMENSIONS (mm are the original dimensions)

A
UNIT A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) θ
max.

mm
0.15 0.95 0.30 0.2 6.6 4.5 6.6 0.75 0.4 0.5 8o
1.1 0.25 0.65 1 0.2 0.13 0.1
0.05 0.80 0.19 0.1 6.4 4.3 6.2 0.50 0.3 0.2 0o

Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.

OUTLINE REFERENCES EUROPEAN

ISSUE DATE
VERSION IEC JEDEC JEITA PROJECTION

99-12-27
SOT360-1 MO-153
03-02-19

Fig. 14. Package outline SOT360-1 (TSSOP20)

74HC_HCT373 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved

Product data sheet Rev. 8 — 6 September 2021 12 / 16

Nexperia 74HC373; 74HCT373
Octal D-type transparent latch; 3-state

DHVQFN20: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads;
20 terminals; body 2.5 x 4.5 x 0.85 mm SOT764-1

D B A

A
A1
E c

terminal 1 detail X
index area

terminal 1
e1 C
index area
v C A B
e b y1 C y
w C
2 9

1 10

Eh e

20 11

19 12
Dh X

0 2.5 5 mm

scale

Dimensions (mm are the original dimensions)

Unit A(1) A1 b c D(1) Dh E(1) Eh e e1 L v w y y1

max 1.00 0.05 0.30 4.6 3.15 2.6 1.15 0.5

mm nom 0.90 0.02 0.25 0.2 4.5 3.00 2.5 1.00 0.5 3.5 0.4 0.1 0.05 0.05 0.1
min 0.80 0.00 0.18 4.4 2.85 2.4 0.85 0.3
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. sot764-1_po

Outline References European

Issue date
version IEC JEDEC JEITA projection
03-01-27
SOT764-1 --- MO-241 ---
14-12-12

Fig. 15. Package outline SOT764-1 (DHVQFN20)

74HC_HCT373 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved

Product data sheet Rev. 8 — 6 September 2021 13 / 16

Nexperia 74HC373; 74HCT373
Octal D-type transparent latch; 3-state

12. Abbreviations
Table 10. Abbreviations
Acronym Description
CMOS Complementary Metal Oxide Semiconductor
ESD ElectroStatic Discharge
HBM Human Body Model
MM Machine Model
TTL Transistor-Transistor Logic

13. Revision history

Table 11. Revision history
Document ID Release date Data sheet status Change notice Supersedes
74HC_HCT373 v.8 20210906 Product data sheet - 74HC_HCT373 v.7
Modifications: • Type number 74HC373DB (SOT339-1/SSOP20) removed.
74HC_HCT373 v.7 20200722 Product data sheet - 74HC_HCT373 v.6
Modifications: • The format of this data sheet has been redesigned to comply with the identity
guidelines of Nexperia.
• Legal texts have been adapted to the new company name where appropriate.
• Type number 74HCT373DB (SOT339-1/SSOP20) removed.
• Table 4: Derating values for Ptot total power dissipation updated.
74HC_HCT373 v.6 20160226 Product data sheet - 74HC_HCT373 v.5
Modifications: • Type numbers 74HC373N and 74HCT373N (SOT146-1) removed.
74HC_HCT373 v.5 20111213 Product data sheet - 74HC_HCT373 v.4
Modifications: • Legal pages updated.
74HC_HCT373 v.4 20100903 Product data sheet - 74HC_HCT373 v.3
74HC_HCT373 v.3 20060120 Product data sheet - 74HC_HCT373_CNV v.2
74HC_HCT373_CNV v.2 19970827 Product specification - -

74HC_HCT373 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved

Product data sheet Rev. 8 — 6 September 2021 14 / 16

Nexperia 74HC373; 74HCT373
Octal D-type transparent latch; 3-state
injury, death or severe property or environmental damage. Nexperia and its

14. Legal information suppliers accept no liability for inclusion and/or use of Nexperia products in
such equipment or applications and therefore such inclusion and/or use is at
the customer’s own risk.
Quick reference data — The Quick reference data is an extract of the
Data sheet status product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
Document status Product Definition Applications — Applications that are described herein for any of these
[1][2] status [3] products are for illustrative purposes only. Nexperia makes no representation
Objective [short] Development This document contains data from or warranty that such applications will be suitable for the specified use
data sheet the objective specification for without further testing or modification.
product development. Customers are responsible for the design and operation of their applications
and products using Nexperia products, and Nexperia accepts no liability for
Preliminary [short] Qualification This document contains data from
any assistance with applications or customer product design. It is customer’s
data sheet the preliminary specification.
sole responsibility to determine whether the Nexperia product is suitable
Product [short] Production This document contains the product and fit for the customer’s applications and products planned, as well as
data sheet specification. for the planned application and use of customer’s third party customer(s).
Customers should provide appropriate design and operating safeguards to
minimize the risks associated with their applications and products.
[1] Please consult the most recently issued document before initiating or
completing a design. Nexperia does not accept any liability related to any default, damage, costs
[2] The term 'short data sheet' is explained in section "Definitions". or problem which is based on any weakness or default in the customer’s
[3] The product status of device(s) described in this document may have applications or products, or the application or use by customer’s third party
changed since this document was published and may differ in case of customer(s). Customer is responsible for doing all necessary testing for the
multiple devices. The latest product status information is available on customer’s applications and products using Nexperia products in order to
the internet at https://www.nexperia.com. avoid a default of the applications and the products or of the application or
use by customer’s third party customer(s). Nexperia does not accept any
liability in this respect.
Definitions Limiting values — Stress above one or more limiting values (as defined in
Draft — The document is a draft version only. The content is still under the Absolute Maximum Ratings System of IEC 60134) will cause permanent
internal review and subject to formal approval, which may result in damage to the device. Limiting values are stress ratings only and (proper)
modifications or additions. Nexperia does not give any representations or operation of the device at these or any other conditions above those
warranties as to the accuracy or completeness of information included herein given in the Recommended operating conditions section (if present) or the
and shall have no liability for the consequences of use of such information. Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
Short data sheet — A short data sheet is an extract from a full data sheet
the quality and reliability of the device.
with the same product type number(s) and title. A short data sheet is
intended for quick reference only and should not be relied upon to contain Terms and conditions of commercial sale — Nexperia products are
detailed and full information. For detailed and full information see the relevant sold subject to the general terms and conditions of commercial sale, as
full data sheet, which is available on request via the local Nexperia sales published at http://www.nexperia.com/profile/terms, unless otherwise agreed
office. In case of any inconsistency or conflict with the short data sheet, the in a valid written individual agreement. In case an individual agreement is
full data sheet shall prevail. concluded only the terms and conditions of the respective agreement shall
apply. Nexperia hereby expressly objects to applying the customer’s general
Product specification — The information and data provided in a Product
terms and conditions with regard to the purchase of Nexperia products by
data sheet shall define the specification of the product as agreed between
customer.
Nexperia and its customer, unless Nexperia and customer have explicitly
agreed otherwise in writing. In no event however, shall an agreement be No offer to sell or license — Nothing in this document may be interpreted
valid in which the Nexperia product is deemed to offer functions and qualities or construed as an offer to sell products that is open for acceptance or the
beyond those described in the Product data sheet. grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein
Disclaimers may be subject to export control regulations. Export might require a prior
Limited warranty and liability — Information in this document is believed authorization from competent authorities.
to be accurate and reliable. However, Nexperia does not give any
Non-automotive qualified products — Unless this data sheet expressly
representations or warranties, expressed or implied, as to the accuracy
states that this specific Nexperia product is automotive qualified, the
or completeness of such information and shall have no liability for the
product is not suitable for automotive use. It is neither qualified nor tested in
consequences of use of such information. Nexperia takes no responsibility
accordance with automotive testing or application requirements. Nexperia
for the content in this document if provided by an information source outside
accepts no liability for inclusion and/or use of non-automotive qualified
of Nexperia.
products in automotive equipment or applications.
In no event shall Nexperia be liable for any indirect, incidental, punitive,
In the event that customer uses the product for design-in and use in
special or consequential damages (including - without limitation - lost
automotive applications to automotive specifications and standards,
profits, lost savings, business interruption, costs related to the removal
customer (a) shall use the product without Nexperia’s warranty of the
or replacement of any products or rework charges) whether or not such
product for such automotive applications, use and specifications, and (b)
damages are based on tort (including negligence), warranty, breach of
whenever customer uses the product for automotive applications beyond
contract or any other legal theory.
Nexperia’s specifications such use shall be solely at customer’s own risk,
Notwithstanding any damages that customer might incur for any reason and (c) customer fully indemnifies Nexperia for any liability, damages or failed
whatsoever, Nexperia’s aggregate and cumulative liability towards customer product claims resulting from customer design and use of the product for
for the products described herein shall be limited in accordance with the automotive applications beyond Nexperia’s standard warranty and Nexperia’s
Terms and conditions of commercial sale of Nexperia. product specifications.
Right to make changes — Nexperia reserves the right to make changes Translations — A non-English (translated) version of a document is for
to information published in this document, including without limitation reference only. The English version shall prevail in case of any discrepancy
specifications and product descriptions, at any time and without notice. This between the translated and English versions.
document supersedes and replaces all information supplied prior to the
publication hereof.
Trademarks
Suitability for use — Nexperia products are not designed, authorized or
warranted to be suitable for use in life support, life-critical or safety-critical Notice: All referenced brands, product names, service names and
systems or equipment, nor in applications where failure or malfunction trademarks are the property of their respective owners.
of an Nexperia product can reasonably be expected to result in personal

74HC_HCT373 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved

Product data sheet Rev. 8 — 6 September 2021 15 / 16

Nexperia 74HC373; 74HCT373
Octal D-type transparent latch; 3-state

Contents
1. General description...................................................... 1
2. Features and benefits.................................................. 1
3. Ordering information....................................................1
4. Functional diagram.......................................................2
5. Pinning information......................................................3
5.1. Pinning.........................................................................3
5.2. Pin description............................................................. 4
6. Functional description................................................. 4
7. Limiting values............................................................. 4
8. Recommended operating conditions..........................5
9. Static characteristics....................................................5
10. Dynamic characteristics............................................ 6
10.1. Waveforms and test circuit........................................ 8
11. Package outline........................................................ 11
12. Abbreviations............................................................ 14
13. Revision history........................................................14
14. Legal information......................................................15

© Nexperia B.V. 2021. All rights reserved

For more information, please visit: http://www.nexperia.com
For sales office addresses, please send an email to: [email protected]
Date of release: 6 September 2021

74HC_HCT373 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2021. All rights reserved

Product data sheet Rev. 8 — 6 September 2021 16 / 16