0% found this document useful (0 votes)

2 views

CNTRL2 v1_8 Installation-Programming Guide English

The document provides installation and programming instructions for the 2GIG-CP2 wireless security system, emphasizing compliance with NFPA standards for smoke detectors. It outlines the system's features, including a color touch screen control panel, support for various wireless sensors, and options for home automation integration. Additionally, it highlights the importance of proper installation to maintain ETL listing and potential insurance discounts for users with security systems.

Uploaded by

Guillermo Garcia

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

2 views

CNTRL2 v1_8 Installation-Programming Guide English

Uploaded by

Guillermo Garcia

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 50

Wireless Security System

2GIG-CP2

Installation & Programming

Instructions
National Fire Protection Association Standard #72
Recommendations for Smoke Detectors
STANDARD FOR ALARM LOCATION
Smoke detectors used with this system should be installed in accordance
with Chapter 2 of the National Fire Alarm Code, ANSI/NFPA 72 (National Fire
Protection Association, Batterymarch Park, Quincy, MA 02269) which reads as
follows:
2-1.1.1 Smoke alarms shall be installed outside of each separate sleeping area
in the immediate vicinity of the bedrooms and on each additional story of the
family living unit including basements and excluding crawl spaces and unfinished
attics. In new construction, a smoke alarm shall be installed in each sleeping
room.
2-1.1.2 For family living units with one or more split levels (i.e., adjacent levels
with less than one full story separation between levels), a smoke alarm required by
2-1.1.1 shall suffice for an adjacent lower level, including basements. (Exception:
Where there is an intervening door between one level and the adjacent lower
level, a smoke alarm shall be installed on the lower level.) THIS SECURITY SYSTEM COMPLIES WITH
✔ Ceiling mounted smoke alarms should be located in the center of the room NFPA REQUIREMENTS FOR TEMPORAL
or hall, or not less than 4 inches from any wall. When the alarm is mounted PULSE SOUNDING OF FIRE NOTIFICATION
on a wall, the top of the alarm should be 4 to 12 inches from the ceiling.
APPLIANCES.
✔ Do not install smoke alarms where normal ambient temperatures are above
100°F (37.8°C), or below 40°F (4°C). Also, do not locate alarm in front
of air conditioners, heating registers, or other locations where normal air
circulation will keep smoke from entering the detector.
A-2.5.2.1 Smoke Detection - Are More Smoke Alarms Desirable? The required
number of smoke alarms might not provide reliable early warning protection for
those areas separated by a door from the areas protected by the required smoke
alarms. For this reason, it is recommended that the householder consider the use
of additional smoke alarms for those areas for increased protection. The additional
areas include the basement, bedrooms, dining room, furnace room, utility room,
and hallways not protected by the required smoke alarms. The installation of
smoke alarms in kitchens, attics (finished or unfinished), or garages is not
normally recommended, as these locations occasionally experience conditions
that can result in improper operation.
Smoke alarms are not to be used with detector guards unless the combination
has been evaluated and found suitable for the purpose.

Figure 1. Smoke Alarm Locations

Table of Contents
Introduction................................................................................ 2 Programming Outline .............................................................. 16
System Overview ....................................................................... 3 SIA CP01 Defaults ............................................................... 16

Control Panel Features ............................................................. 4 Programming Question Table ................................................. 17

Installation Outline .................................................................... 5 System Sensor Types .............................................................. 18

Sensor Types (Zones) .......................................................... 18
Wireless Installation Tips .......................................................... 5
System Vocabulary Table ........................................................ 19
Wireless System Sensors ......................................................... 6
2GIG-DW10 Thin Door/Window Contact ............................... 6 Installer Programming ............................................................ 20
2GIG-DW20R Recessed Door Contact ................................. 6 RF Sensor Programming ..................................................... 20
2GIG-PIR1 Passive Infrared Motion Detector ........................ 6 RF Sensor Programming Outline ................................... 20
2GIG-KEY1 4-Button Key Ring Remote ................................ 6 RF Sensor Summary Screen ......................................... 21
2GIG-PANIC1 Panic Button Remote...................................... 6 RF Sensor Programming Steps ..................................... 22
2GIG-GB1 Glass Break Detector........................................... 6 Wired Sensor Programming ................................................ 24
2GIG-SMKT2 Smoke and Heat Detector ............................... 6 Wired Sensor Programming Outline .............................. 24
2GIG-TS1 Wireless Touch Screen Keypad ............................ 6 Wired Sensor Summary Screen .................................... 24
2GIG-PAD1 Wireless Keypad ................................................ 6 Wired Sensor Programming Steps................................. 25
2GIG-TAKE-345 Super Switch Wireless Takeover Module .... 6 RF Key Fob Programming ................................................... 26
RF Key Fob Programming Outline ................................. 26
System Accessories.................................................................. 7 RF Key Fob Summary Screen ....................................... 26
2GIG-GSMx GSM Module ..................................................... 7 RF Key Fob Programming Steps ................................... 27
2GIG-ANT1 Internal GSM Antenna ....................................... 7 RF Keypad Programming .................................................... 28
2GIG-ANT1X External In-wall GSM Antenna ........................ 7 RF Keypad Programming Outline .................................. 28
2GIG-ANT2X External Attic Mount GSM Antenna................. 7 RF Keypad Summary Screen ........................................ 28
2GIG-ANT4X External In-wall GSM Antenna ........................ 7 RF Keypad Programming Steps..................................... 29
2GIG-BATT1 Standard Battery Pack ..................................... 7 Control Panel Programming Questions ............................... 30
2GIG-BATT1X Extended Battery Pack .................................. 7
2GIG-AC1 Replacement Power Supply ................................. 7 Final Installation Setup ........................................................... 39
Exiting Programming ........................................................... 39
Installation.................................................................................. 8 Customizing the Installation ................................................. 39
Control Panel Mounting Plate ................................................ 8
Wireless Sensors ................................................................... 8 Installer Testing........................................................................ 40
Hardwired Loops.................................................................... 8 Testing the System .............................................................. 40
Remote Alarm Sounder ......................................................... 9 Sounder Disable/Enable ...................................................... 40
Solid State Output.................................................................. 9 Zone Reporting Test ............................................................ 40
Communicator Telephone Line .............................................. 9 Walk Test Mode.................................................................... 41
Optional GSM Module Installation ....................................... 10 Signal Strength Indicators .............................................. 41
Control Panel Wiring ............................................................ 11 Radio Status Mode .............................................................. 42
Backup Battery Connection and Power Supply Wiring ........ 11 GSM Radio Test ............................................................. 42
Control Panel and Power Supply Mounting ......................... 11 Telephone Test ..................................................................... 42
Restoring Programming Defaults ......................................... 42
Main Display Screens.............................................................. 12 Restore Defaults .................................................................. 42
Home Screen ....................................................................... 12
Security Screen ................................................................... 12 Regulatory Information & Limited Warranty ......................... 43
Arming Screen ..................................................................... 12 Wireless Product Notice ...................................................... 43
Menu Screen ....................................................................... 12 FCC Notice .......................................................................... 43
Status Screen ...................................................................... 12 FCC Telephone Rules and Regulations ............................... 43
Industry Canada Notices ..................................................... 43
Toolbox Screens ...................................................................... 13 Limited Warranty .................................................................. 43
Toolbox Screens .................................................................. 13
Installer Code Entry Screen ................................................. 13 Reference Programming Question Table............................... 44
Installer Toolbox Screen ....................................................... 13 Reference System Vocabulary Table ...................................... 45
System Configuration Screen .............................................. 13 Index ......................................................................................... 46
System Status Icons ............................................................... 14
AC Power Icon ..................................................................... 14
Phone Line Failure Icon ....................................................... 14
Sounder Disable Icon .......................................................... 14
Backup Battery Status Icon ................................................. 14
Test Mode Icon .................................................................... 14
Touch Screen Keypad Traffic Icon ........................................ 14
GSM Radio Icon .................................................................. 14
Interior Sensor Open Icon.................................................... 14
Programming Navigation ........................................................ 15
Navigation Arrows & Go To Button....................................... 15
Questions without Sub-options ............................................ 15
Questions with Sub-options ................................................. 15
Questions with Data to Enter ............................................... 15
Other Buttons Displayed ...................................................... 15

1
Introduction
The Go!Control Security System represents a significant
advancement in fully supervised wireless security systems. The
security system Control Panel incorporates many advanced
and sophisticated features. The system can be expanded and
customized to fit the installation’s specific needs.
Designed to meet or exceed the requirements for ETL Listed
residential security installations, the system also conforms to the
Security Industry Association’s Control Panel Standard ANSI/SIA
CP-01-2007.
✓ NOTE: Failure to install the Control Panel and accessories in
accordance with ETL requirements listed in this manual voids
the ETL listing mark assigned by Intertek.
Many insurance companies offer discounts on homeowners’ and
renters’ policies when a security system is installed. Discount
credits vary with different companies and generally increase in
savings with an increase in the level of protection. Inform the user
to ask their insurance agent about savings available.
This security system is ETL Listed. For an ETL smoke alarm
system, there must be at least one smoke detector programmed
into the Control Panel to meet National Fire Protection Association 2GIG-CP2
(NFPA) Rule 72-Chapter 2, and UL 217 requirements. Many
insurance companies require meeting these requirements to
qualify for a discount. For an ETL smoke alarm system, use only
approved model smoke detectors with this Control Panel.
✓ NOTE: Some cities and municipalities may require an alarm
system permit. Check with the local authorities before installing
this system.

REFERENCE ONLY - REFER TO ADDENDUM 230373 FOR PROPER

INSTALLATION AND WIRING DIAGRAM CONTROL PANEL

UL NOTE: WIRING FOR ALL WIRED SENSORS AND ANNUNCIATORS MUST USE
UL LISTED LOW VOLTAGE CL2X OR BETTER GRADE WIRE. SENSOR AND DISPLAY
VOLTAGES MUST COMPLY WITH CLASS 2 LOW VOLTAGE REQUIREMENTS. TELEPHONE LINE
FROM RJ31X
TELEPHONE
TELEPHONE JACK JACK
HARDWIRE LOOPS
CAN BE PROGRAMMED
AS NORMALLY OPEN OR CLOSED
8 - HARDWIRE LOOP 2
7 - HARDWIRE LOOP 1 ALL OUTPUT
NORMALLY CLOSED PIEZO VOLTAGES
NORMALLY
CONTACT 6 - BELL (-)
OPEN SIREN ARE CLASS 2
CONTACT 5 - BELL (+)
SUPERVISED BELL OUTPUT
2.2 K 2.2 K 6-12 VDC @ 120 mA MAXIMUM 4 - OPEN COLLECTOR OUTPUT
3 - GROUND
END-OF-LINE RESISTORS ARE 2 - 14 VDC POWER INPUT (-)
OPTIONAL ON HARDWIRE LOOPS
1 - 14 VDC POWER INPUT (+)

OPEN COLLECTOR OUTPUT

250 mA @ 16 VDC MAXIMUM
NOTE: TERMINAL 1 WILL ONLY
PROVIDE DC POWER WHEN
120 VAC 60 HZ THE CONTROL PANEL'S
1K LED PLUG-IN 14 VDC
1.7 AMP SWITCHING
POWER SUPPLY IS CONNECTED
POWER SUPPLY TO AN AC POWER SOURCE

EXAMPLE HOOKUP SHOWING AN ARMED LED, OBSERVE

THE OPEN COLLECTOR OUTPUT CAN BE PROGRAMMED POLARITY WHEN
TO ACTIVATE DURING VARIOUS CONDITIONS CONNECTING THE
POWER SUPPLY !!!

Figure 2. Control Panel Wiring Diagram

2
System Overview
The system’s Control Panel features a color touch screen display that The optional GSM radio modem also allows 2-way communications
allows control of all system functions and programming. The display with the Alarm.com server. Through this server, subscribers can
clearly shows the installer and subscriber system and installation query and control their system using a computer browser from
status. The helpful scrolling text, along with the voice prompts anywhere in the world. The Alarm.com server can also send
that the Control Panel sounds, make installation, programming, messages, time corrections, and software updates to the Control
and operation very easy compared to keypad-programmed and Panel. Special messages from the server are displayed to the
operated security systems of the past. subscriber on the Control Panel’s color touch screen.
The system supports 48 wireless sensors of various types, two For home control, the Control Panel’s built-in Z-Wave radio module
hardwire loops, 15 sensor response types, a supervised bell output, allows controlling and monitoring various home automation devices
and a programmable solid-state control output. An on-board digital such as lighting, locks, heating, and air conditioning.
communicator reports alarms and trouble to a central monitoring Eight user codes including a duress code are supported. User
station receiver via the standard telephone network. The Control “one” is the master code that can add or delete the other seven
Panel also supports 2-way voice communications with the Central user codes. The Installer Code has access to system programming.
Station.
The front panel and buttons serve as controls as well as
An internal 345 MHz narrow-band radio receiver detects signals
indicators. Pressing the button displays emergency icons on the
from wireless system sensors. The high-gain receiver allows for
easy placement of the wireless sensors so signals can be received display for Panic, Fire, and Emergency alarm activation (each has
in even the toughest of installation environments. programmable options and can be enabled or disabled). Pressing
the button changes the system display to the Home Screen.
When the optional Model 2GIG-XCVR2 900 MHz transceiver is
installed, it sends and receives signals with accessory wireless
touch screen keypads. Touch screen keypads allow remote control
of the system through the same graphic interface design as the
Control Panel.
For enhanced operation, an optional Model 2GIG-GSMx global
system for mobile communications module (GSM radio modem)
can be installed in the field. With the optional GSM radio modem
installed, the system will have wireless Central Station reporting
capability. 2-way voice communication with the Central Station can
also go “over-the-air” through the GSM radio modem.

Touch Screen Cell

Hardwire Hardwire Site
Loop Loop
#1 Subscriber’s
#2 Color Display Subscriber’s
Subscriber PDA
Computer
Home &
Siren
Voice

Emergency
Buttons
Central Station
Existing Public
Receiver
Sensor Switched
Hardwire Inputs

Telephone
Communicator

Installation
Speaker Color LCD Network
Digital

& Display with Optional

Microphone Touch Screen GSM
Module
Alarm.com
PIR GSM
CONTROL PANEL Web site
Door / Motion Telephone
Window Sensors Network
Sensors
CPU

Alarm.com
Glass Server
Break
Sensors Alarm.com
Standard 345 MHz Receiver
Bell System Z-Wave Infrastructure Database
or Optional
345 MHz / 900 MHz Transceiver Output Power Radio
CO
Sensors
Thermostat

Power
Smoke Supply
Sensors Lighting
Control
Key Wireless
Panic Fobs Wireless Touch Piezo
Buttons Keypads Screens Siren
120 VAC Door
Input Locks
Up to 48 Wireless Sensors per System Power

Figure 3. System Block Diagram

3
Control Panel Features

ALARM SOUNDER COLOR DISPLAY

AND SPEAKER WITH TOUCH SCREEN
Sounds all system local alarms, Shows all system information, status,
voice prompts, system sounds, and programming, and functions as the
audio for 2-way voice communications keypad.
with the Central Station
Display also cycles clock,
calendar, and weather
(press to manually change)
EMERGENCY
BUTTON / INDICATOR
Lights WHITE when enabled for
emergency alarm

Flashes WHITE during

emergency alarm

MICROPHONE
For voice communication
with the Central Station

HOME
BUTTON / INDICATOR
Lights GREEN when ALL sensors are closed (ready to arm)
Sensor Status
Not lit when ANY sensor is open (not ready to arm)

Lights RED while system is armed HOME

Arming Status Blinks RED during the Entry Delay BUTTON / INDICATOR
Indicator flashes during power outages (system on battery backup)
Blinks RED during an alarm Flashes GREEN when ALL sensors are closed (ready to arm)
Alarm Memory Power Outage
Blinks RED after an alarm while system is still armed Flashes ORANGE when ANY sensor is open (not ready to arm)
Flashes RED while system is armed

Figure 4. Control Panel External Features

BACKUP BATTERY PACK "THIRD HAND"

HANGER STRAP
7.2 Volt Ni-mh battery pack is included
with the Control Panel, replacement Hooks onto mounting plate during installation
part number 2GIG-BATT1 to hold the Control Panel while wiring
For UL985 installations, use the
Model 2GIG-BATT1X battery pack
TELEPHONE LINE
MONITOR TERMINALS
TELEPHONE JACK Terminals for connecting lineman's
For RJ45 connection to installation's "buttset" for monitoring the telephone line
RJ31X telephone jack, incoming and
outgoing lines for full line seizure

MAIN RECEIVER MODULE

345 MHz receiver for wireless sensors
Optional Model XCVR2 345 / 900 MHz
transceiver for touch screen keypads
GSM ANTENNA (HIDDEN) (XCVR2 is not for UL985 installations)
Internal Model 2GIG-ANT1 GSM antenna
mounts in the side of the Control Panel case OPTIONAL GSM RECEIVER MODULE
Model 2GIG-GSMx GSM Module for over-the-air
communication with the Alarm.com
TERMINAL BLOCK Central Station
Connections for power, solid state output
bell, and hardwire loops

Figure 5. Control Panel Internal Features

4
Installation Outline Wireless Installation Tips
The following outline is intended to guide the installing alarm When installing any wireless system, certain limitations must
dealer through the complete installation of a Go!Control system. be considered. Low power wireless transmitter signals will not
Use the following outline in conjunction with this copy of the broadcast equally through all types of construction materials. The
Installation Instructions to guide you through the installation. Control Panel contains a very sensitive receiver that should allow
placement of transmitters in almost all locations.
1. Unpack the system. Identify the system components.
Here are some general wireless guidelines that should be reviewed
2. Plan the installation by creating an installation floor plan. before beginning the installation. Follow these tips to create the
Determine the best centralized location for the Control Panel. best possible functioning wireless installation.
Decide on where the wireless sensors will be installed.
3. Identify an un-switched 120 VAC power source for plugging
in the Control Panel’s power supply.
4. Identify or install a U.S.O.C. RJ31X telephone jack for CONTROL PANEL LOCATION RELATIVE TO SENSORS
connection of the Control Panel’s communicator.
5. Use the Control Panel’s mounting plate as a template to mark
the mounting location for the Control Panel. Mark any drywall
cutouts behind the mounting plate required for the installation
and make the cutouts.
6. Attach the mounting plate to the wall using three screws.
RIGHT WRONG!
7. Install each of the system’s wireless sensors. If either of the CENTRALLY LOCATE SENSORS AT THE OTHER END OF
CONTROL PANEL HOUSE MIGHT BE TOO FAR AWAY
two hardwire loops are going to be used, install the contacts
and route the loop wire to the Control Panel’s wall cutout. Use
the log in the quick programming guide to document each
sensor’s ID number and location.
8. Install the optional remote sounder, and route the connection CONTROL PANEL LOCATION HEIGHT
wire to the Control Panel’s wall cutout.
9. Route the telephone line from the RJ31X jack to the Control
Panel’s wall cutout.
CONTROL CONTROL
10. Using the “third hand” strap, hang the Control Panel on the PANEL PANEL
mounting plate in preparation for wiring.
BASEMENT BASEMENT
11. Connect all wiring to the Control Panel’s terminal block.
RIGHT WRONG!
12. Plug the telephone line into the Control Panel’s telephone
jack. MOUNT CONTROL PANEL AS HIGH ABOVE LOCATING CONTROL PANEL BELOW
EARTH LEVEL AS PRACTICAL EARTH LEVEL WILL IMPAIR RANGE
13. Plug the backup battery connector into the connector on the
Control Panel’s circuit board.
14. Swing the Control Panel up, placing the bottom over the lip of
the mounting bracket. Push the top of the Control Panel into
SENSOR SIGNAL LOSS THROUGH MATERIALS
the mounting bracket until it snaps into place, then secure it
with the retaining screw.
90% - 100% 65% - 95% 10% - 70%
15. Plug the power supply into the un-switched 120 VAC wall OF FULL POWER OF FULL POWER OF FULL POWER
outlet.
16. Program the system as described in this manual and mark
the check boxes in the Operation and User’s Guide to indicate
any custom setup to the subscriber.
17. Test the system as described in this manual.
WALLBOARD AND LIGHT CONCRETE CONCRETE WITH STEEL
18. Instruct the subscriber on the system operation and provide WOOD STUDS OR BRICK REINFORCEMENT OR
the Operation and User’s Guide to the subscriber. METAL LATH AND PLASTER

LOCATION OF SENSORS

SENSOR
Less
than DOOR
DOOR 3 ft.
above Wall
slab
Min. Concrete Concrete
3 ft. Large
slab slab
metal
floor floor
appliance
SENSOR (refrig.)
SENSOR

RIGHT WRONG! WRONG!

Figure 6. Wireless Installation Tips

5
Wireless System Sensors
2GIG-DW10 2GIG-GB1
Thin Door/Window Contact Glass Break Detector
• For narrow applications, • Monitors for the sound
sensor is only 3/4” wide of breaking glass
• Fully supervised • Two test LEDs
• Rare earth magnet • Dual shatter recognition
• Lithium battery technology (thud then crash)
• Supports internal and external contacts • Lithium battery
• Can be used for two • 345 MHz
zones of protection • ETL Listed
• 345 MHz
• ETL Listed

2GIG-DW20R 2GIG-SMKT2
Recessed Door Contact Smoke and Heat Detector
• Compact size, only 2-1/2” long • Photoelectric-type detector
• Fully supervised with rate-of-rise and fixed
• Rare earth magnet 135° heat sensors
• Lithium battery • Status indicator
• 345 MHz • Built-in 85 dBA sounder
• ETL Listed • Lithium battery
• 345 MHz
• ETL Listed

2GIG-TS1
2GIG-PIR1 Wireless Touch Screen Keypad
Passive Infrared Motion Detector • Wireless communication
• Dual element sensor with with Control Panel
50’ by 50’ range • Same graphic interface
• 45 lb. pet immune as Control Panel
• 90 degree look down • Supports all functions
• Lithium battery of the Control Panel
• 345 MHz • 900 MHz
• ETL Listed • NOTE: Not for UL985
installations.
2GIG-PAD1
Wireless Keypad
• Arms system in Stay
or Away Mode
2GIG-KEY1
• Disarms system
4-Button Key Ring Remote • Fire and Panic
• Arms system in Stay or Away Mode
emergency functions
• Disarms system
• Lithium batteries
• Auxiliary output and
• 345 MHz
emergency functions
• ETL Listed
• Lithium battery
• 345 MHz
• ETL Listed

2GIG-TAKE-345
Super Switch Wireless
Takeover Module
• Eight-channel transmitter
2GIG-PANIC1
• Converts up to eight
Panic Button Remote hardwired loops into eight
• For triggering emergency alarm
wireless sensor zones
• Small and lightweight
• 9-16 VDC, 50 mA
• 5-second button lockout
• Can be powered from
• Lithium battery
existing Control Panel
• 345 MHz
• 345 MHz
• ETL Listed
• ETL Listed

6
System Accessories
2GIG-GSMx 2GIG-BATT1
GSM Module Standard Battery Pack
• Cellular telephone module • Standard battery supplied
• Plugs into Control Panel with Control Panel
• Provides 2-way GSM • Also available as a replacement
radio communication item
• Enrolls with cellular service provider • Nickel metal hydride (NiMH) battery

2GIG-ANT1 2GIG-BATT1X
Internal GSM Antenna Extended Battery Pack
• Antenna installs inside • Optional extra capacity battery
Control Panel • Replaces standard internal
• Plugs into GSM module Control Panel battery
• Small size • Required for UL985 fire
• Locking connector warning system listing
• Nickel metal hydride (NiMH) battery

2GIG-ANT1X 2GIG-AC1
External In-wall GSM Antenna Replacement Power Supply
• Antenna installs in the wall • High efficiency switching
behind Control Panel power supply
• 2-foot cable • 120 VAC @ 60 Hz input
• Plugs into GSM module • 14 VDC @ 1700 mA output
• Locking connector • Screw terminals for wiring
connecting to the Control Panel
• Includes retaining bracket
for standard and Decora style outlets.

2GIG-ANT2X
External Attic Mount GSM
Antenna
• Antenna installs in attic
above Control Panel
• 10-foot cable
• Plugs into GSM module
• Locking connector

2GIG-ANT4X
External In-wall GSM
Antenna
• Antenna installs in the wall
behind Control Panel
• 2-foot cable
• Plugs into GSM module
• Locking connector

7
Installation
Control Panel Mounting Plate SI L'ANTENNE GSM EXTERNE
EST UTILISÉE, RETIRER
The Control Panel should be mounted on the wall in an easy PLAQUE L'ENTRÉE DÉFONÇABLE
DE MONTAGE
location for the subscriber to operate the system.
MONTER
1. Remove the locking screw from the top of the Control Panel case and LA PLAQUE
remove the mounting plate. AVEC 3 VIS

2. Use the mounting plate as a template to mark the wall for the wiring
cutout slot. Use a drywall saw to cut the slot. If using the optional
Model 2GIG-GSMx GSM module with the external Model 2GIG-ANT1X
or Model 2GIG-ANT2X antenna, remove the plastic knockout labeled RETIRER LA VIS DU UTILISER LA PLAQUE
“EXTERNAL ANTENNA” on the mounting plate. Mark and cut a slot in the BOÎTIER ET LA PLAQUE DE MONTAGE COMME
DE MONTAGE GUIDE POUR MARQUER
drywall for the external antenna. LE TROU SUR LE MUR À
TRAVERS DU TROU
3. Attach the mounting plate to the wall using three screws. DÉCOUPÉ DE LA PLAQUE

Wireless Sensors Figure 7. Wall Mounting Template

Each wireless sensor needs to be installed at its desired location.
1. Following the instructions included with each wireless sensor, install each
sensor at its desired location.
2. Use the Installation Log to document each sensor’s ID number and
location.

Hardwired Loops
Hardwired loops can be programmed either normally open (N/O)
or normally closed (N/C). End-of-line resistors (EOLR) can also be
used to supervise the loops.
Only contacts should be used with the hardwired loops. The Control
Panel does not support powering external devices (PIR’s, etc.).
✓ NOTE: HARDWIRED LOOPS CANNOT BE USED FOR A CO
OR FIRE SENSOR LOOP.
1. If either of the two hardwired loops are going to be used, install the contacts
and route the loop wire to the Control Panel’s wall cutout.
2. If end-of-line supervision is required for the loop, install a 2.2K ohm resistor Figure 8. Typical Door Sensor Installation
(not supplied) as shown in the loop illustration.

HARDWIRE LOOP WIRING EXAMPLES

LOOP 1 OR 2

LOOP 1 OR 2
HARDWIRE

HARDWIRE

HARDWIRE
GROUND

GROUND

N.C. N.C. N.C.

N.O.

N.C. N.O. N.O. N.O.

LOOP LOOP

2.2K EOLR 2.2K EOLR 2.2K EOLR

HARDWIRE LOOPS NEED TO BE
PROGRAMMED FOR CONTACT TYPE N.C. N.O. MIXED
EOL LOOP EOL LOOP EOL LOOP

Figure 9. Hardwired Loop Wiring

8
Installation
Remote Alarm Sounder
The Control Panel provides two terminals for an optional connection THE BELL OUTPUT CAN BE PROGRAMMED
FOR SUPERVISION TO DETECT IF THE
to a remote electronic alarm sounder. DO NOT CONNECT AN WIRE TO THE BELL IS CUT
ELECTROMECHANICAL BELL TO THESE TERMINALS. The 8 - HARDWIRE LOOP 2
bell terminals can be supervised. If bell trouble reporting is enabled 7 - HARDWIRE LOOP 1
and the wire between the Control Panel and sounder is cut, the 6 - BELL (-)
Control Panel will report bell trouble. 5 - BELL (+)
SUPERVISED BELL OUTPUT 4 - OPEN COLLECTOR OUTPUT
1. Install the remote sounder in a secure location where it can easily be 6-12 VDC @ 120 mA MAXIMUM 3 - GROUND
PIEZO
heard. SIREN 2 - 14 VDC POWER INPUT (-)
1 - 14 VDC POWER INPUT (+)
2. Route wiring from the remote sounder location to the Control Panel’s wall
cutout. USE SOLID STATE SOUNDERS ONLY
DO NOT CONNECT TO AN ELECTROMECHANICAL BELL !!!

Solid State Output

The Control Panel provides one solid state output that can be
Figure 10. Remote Sounder Wiring
programmed to activate during various conditions. The output can
switch up to 250 Ma @ 16 VDC to ground. Refer to Figure 11 for
examples of devices wired to the output.
This output will only function while the Control Panel is
receiving power from the wall power supply.
1. Install the device to be controlled by the solid state output.
OPEN COLLECTOR OUTPUT
2. Route wiring from the device location to the Control Panel’s wall cutout. 250 mA @ 16 VDC MAXIMUM NOTE: FOR ETL LISTING, 8 - HARDWIRE LOOP 2
AN EXTERNAL DC BACKUP 7 - HARDWIRE LOOP 1
➜ WARNING: Do not connect an electromechanical bell to these OUTPUT SWITCHES TO POWER SUPPLY IS REQUIRED 6 - BELL (-)
GROUND WHEN ACTIVATED FOR A LOAD CONNECTED
terminals. Damage to the output will occur. 5 - BELL (+)
TO TERMINAL 4
4 - OPEN COLLECTOR OUTPUT
Communicator Telephone Line 3 - GROUND
Both an incoming telephone line and an outgoing telephone line 2 - 14 VDC POWER INPUT (-)
will be connected to the Control Panel. When the communicator 1 - 14 VDC POWER INPUT (+)
activates, all local telephones will be disconnected to prevent 1K LED
an off-hook telephone on the premises from blocking the NOTE: TERMINAL 1 WILL ONLY
PROVIDE DC POWER WHEN
communicator’s call. See Figure 12 for RJ31X jack wiring details. THE CONTROL PANEL'S
EXAMPLE HOOKUP SHOWING AN ARMED LED,
POWER SUPPLY IS CONNECTED
1. Run a 4-conductor telephone cable from the telephone company THE OPEN COLLECTOR OUTPUT CAN BE PROGRAMMED
TO AN AC POWER SOURCE
TO ACTIVATE DURING VARIOUS CONDITIONS
demarcation box to the Control Panel mounting plate.
2. At the demarcation box, disconnect the house telephones that are Figure 11. Solid State Output Wiring
wired to the box output. DO NOT DISTURB THE TELCO INPUT
“DROP” SIDE OF THE BOX OR ANY EARTH GROUNDS.
3. At the demarcation box, connect the RED cable wire to the
box RING, and the GREEN cable wire to the box TIP.
4. At the demarcation box, connect the BLACK cable wire
to the house telephone RING wire(s), and the YELLOW RED (RING IN) INCOMING TELEPHONE LINE
GREEN (TIP IN)
cable wire to the house telephone TIP wire(s). FROM DEMARCATION BOX

RJ31X IMPORTANT !
5. At the Control Panel, connect the cable’s RED wire to TELEPHONE FOR PROPER LINE SEIZURE, ALL HOUSE
TELEPHONE CONNECTIONS MUST PASS
the RJ31X jack’s RING IN terminal, and the GREEN JACK
THROUGH THE RJ31X JACK
wire to the RJ31X jack’s TIP IN terminal. BLACK (RING OUT) OUTGOING TELEPHONE LINE
YELLOW (TIP OUT) TO HOUSE TELEPHONES
6. At the Control Panel, connect the cable’s BLACK wire to
CONTROL PANEL
the RJ31X jack’s RING OUT terminal, and the YELLOW
wire to the RJ31X jack’s TIP OUT terminal. TELEPHONE
JACK
7. Snap the cover on the jack. Plug one end of the modular cable into the
PLUG CABLE PLUG CABLE
jack and slide it through the hole in the mounting plate into the wall. FROM CONTROL FROM JACK
PANEL INTO JACK INTO CONTROL
PANEL

Figure 12. Telephone Jack Wiring

9
Installation
Optional GSM Module Installation
If using the optional GSM module and one of the GSM antennas. 1
Refer to the following steps: PLUG GSM
MODULE INTO
1. Plug the GSM module into the connector on the Control Panel’s circuit CONTROL
board. Secure it with the two screws. PANEL
2A. If using the Model 2GIG-ANT1 internal antenna, remove the antenna
access cover. Route the antenna lead through the opening in the case and
place the flat antenna into the slot. Route the antenna wire under the clip
behind the speaker and plug the antenna connector into the GSM module.
Replace the antenna access cover. See Figure 13.
2
✓ NOTE: The routing of the GSM antenna wire is very critical.
PRY OPEN
Route the wire as directed or GSM radio interference will occur ANTENNA ACCESS
inside the Control Panel. COVER
2B. If using one of the external antennas, simply plug the antenna connector
into the GSM module. The antenna will drop into the wall or mount in
the attic with the cable passing through the slot in the Control Panel’s
mounting plate. See Figures 14 & 15.
✓ NOTE: The GSM SIM card should have been pre-activated by
the factory; if not, contact your service provider. For the GSM
module to function with the system, it will have to be activated
before it can be enrolled by creating an account with the 3
service provider. PLACE
ANTENNA
INTO SLOT
AS SHOWN

ROUTE GSM ANTENNA CABLE

EXACTLY AS SHOWN !!!

4
SECURE GSM
MODULE WITH
TWO SCREWS

ROUTE GSM ANTENNA CABLE

EXACTLY AS SHOWN !!!

Figure 13. Optional GSM Module Installation

2GIG-ANT2X
GSM CONNECTOR GSM ANTENNA
MOUNTED AS HIGH
AS POSSIBLE

ANTENNA HANGS
DOWN INSIDE WALL

2GIG-ANT1X
ANTENNA
COAX TO
CONTROL
PANEL

Figure 14. ANT1X In-wall GSM Antenna Installation Figure 15. ANT2X Attic GSM Antenna Installation
10
Installation
Control Panel Wiring
The Control Panel includes a “third hand” plastic strap that allows 1
the unit to hang on the mounting plate during installation. HANG CONSOLE
3
ON STRAP
PLUG TELEPHONE LINE
1. Hang the Control Panel on the mounting plate using INTO TELEPHONE JACK
the “third hand” strap (see Figure 16). 2
CONNECT HARDWIRE LOOPS,
2. Connect the hardwire loop, external sounder, and open collector EXTERNAL SOUNDER, AND
output wiring (if used ) to the Control Panel’s terminal block. OPEN COLLECTOR OUTPUT
TO TERMINALS
3. Plug the telephone line (if used ) into the connector
on the Control Panel’s circuit board.

Backup Battery Connection and Power Supply Wiring

The backup battery connects to the Control Panel’s circuit board
with a two-pin header assembly.
The power supply features a two-position terminal block for Figure 16. Control Panel Mounting
connecting the power supply to the Control Panel power terminals
(connection wire not included).
1. Determine a good location where there’s a 120 VAC outlet for the
TERMINAL #2 CONTROL PANEL
plug-in power supply. The 120 VAC outlet must be un-switched (an outlet - 14 VDC TERMINALS
POWER
not controlled by a wall switch). DO NOT CONNECT THE POWER
SUPPLY
SUPPLY TO A RECEPTACLE CONTROLLED BY A SWITCH.
2. Route 2-conductor 18 AWG wire from the power supply
location to the Control Panel mounting plate.
TERMINAL #1
3. BEING CAREFUL TO OBSERVE POLARITY, connect the RIGHT + 14 VDC
power supply’s DC + and DC - terminals to the 18 AWG TERMINAL
- 14 VDC
wire. DO NOT PLUG IN THE POWER SUPPLY YET.
4. BEING CAREFUL TO OBSERVE POLARITY, connect the LEFT OBSERVE POLARITY WHEN
18 AWG wire to the Control Panel +14 VDC Terminal #1 (+) TERMINAL CONNECTING THE POWER SUPPLY!!!
and -14 VDC Terminal #2 (-) power input terminals. + 14 VDC

✓ NOTE: Grounding of the Control Panel is NOT required for Figure 17. Power Supply Wiring
proper operation.
5. Plug the backup battery pack’s connector into the connector
on the Control Panel’s circuit board. (The Control Panel 3 SWING CONSOLE UP
will not recognize that the battery is connected until AND SNAP ONTO THE
MOUNTING PLATE
AC power is connected to the power supply.)
★ IMPORTANT: Applicable regulatory agencies require
installation of the extended life backup battery (P/N
1
2GIG-BATT1X) inside the Control Panel for UL985 Household CONNECT
Fire applications. BATTERY

Control Panel and Power Supply Mounting

With all the wiring complete, the Control Panel is ready to power up.
4
1. Swing the Control Panel up, placing the bottom over the lip of the 2 AFTER INSTALLING,
SECURE CONSOLE
mounting bracket. Push the top of the Control Panel into the mounting ALIGN MOUNTING
WITH SCREW IN
PLATE INSIDE OF
bracket until it snaps into place, then secure it with the retaining screw. RETAINING HOLE
CONSOLE BOTTOM EDGE

2. Peel off the adhesive backing from the power supply retaining bracket
Figure 18. Connecting Battery and Closing Panel
and attach the bracket to the outlet with a wall plate screw. Note the
orientation for a standard or Decora style outlet (see Figure 19).
3. Spread the retaining bracket ears and plug the Control Panel’s
power supply into the un-switched 120 VAC outlet. Slots are
provided on the bracket to secure the power supply with a zip-tie.
POWER POWER
4. After about five seconds, the Control Panel will indicate that SUPPLY SUPPLY
power has been applied. IF THE CONTROL PANEL DOES NOT
POWER UP, CHECK THE POWER SUPPLY POLARITY!!!

BRACKET INSTALLED BRACKET INSTALLED

FOR STANDARD FOR DECORA
STYLE OUTLET STYLE OUTLET

Figure 19. Securing the Power Supply

11
Main Display Screens
The Control Panel is programmed and operated using the color
touch-screen display. The display will show various buttons,
indicators, and text to guide the installer and user.

Home Screen
The Home Screen is the top level screen. It shows the system
status with icons to indicate system conditions. It also displays
the time and date. System information scrolls along the top of the
display. The Home Screen displays the SECURITY and SERVICES
buttons. The Silent Control and Display Off buttons are also
displayed. When the system is operating, pressing the button
on the Control Panel will display the Home Screen.
Figure 20. The Home Screen
Security Screen
The Security Screen shows the system status and offers three
buttons for ARM, MENU, and STATUS. The Silent Control button Trouble Alert
and the time and date are also displayed. If messages, alarm, or
trouble alerts are pending, the Security Screen will display buttons Silent Control
indicating the number of pending messages or issues.
Alarm Memory
Arming Screen
The Arming Screen is used to arm the security portion of the
Message
system. It displays the system status and arming buttons for STAY
and AWAY.
An option check box for ENTRY DELAY and a Silent Control button Figure 21. The Security Screen
are displayed. To arm the system without an entry delay, un-check
the ENTRY DELAY check box. To arm silently without sounding the
Exit Delay beeps, press the Silent Control button. Stay Mode
arming always has a silent exit.

Menu Screen
The Menu Screen shows the system status and offers buttons for
ARM and TOOLBOX. If any of the 24-hour emergency options are
enabled, an EMERGENCY button is displayed. Two option check box
buttons for CHIME and VOICE are displayed.
Installer setup can be accessed using the TOOLBOX button.
Figure 22. The Arming Screen
The CHIME button enables/disables chimes for the entire system
(chimes can be independently enabled or disabled for each sensor
number from the Toolbox).
The VOICE button enables/disables voice announcements for
the entire system (voice announcements can be independently
enabled or disabled for each sensor number from the Toolbox).
Voice announcements always sound during alarm conditions.

Status Screen
The Status Screen lists system status and any alerts. The date and
time of alerts are listed in the displayed log.
One option button for SILENCE is displayed; it temporarily stops Figure 23. The Menu Screen
the voice announcement of the system status during the status
display.

Figure 24. The Status Screen

12
Toolbox Screens
The Control Panel is programmed using the “toolbox” screens.
Users can access basic programming functions. Installers can
access basic and Installer Toolbox functions. Users and installers
must enter a valid code to access the programming functions in
the toolbox. Other functions do not require entering a code.

Toolbox Screens
From the Menu Screen, when the TOOLBOX button is pressed, the
system will ask for a User Code then display Toolbox Screen one.
The arrow button displays Toolbox Screens two and three. Each Figure 25. Toolbox Screen One
Toolbox Screen shows option buttons that display sub-menus.

Installer Code Entry Screen

The INSTALLER TOOLBOX button goes to the main programming
area of the Control Panel and can only be accessed by the installer
while the system is disarmed by entering a correct access code.
THE INSTALLER CODE CANNOT DISARM THE SYSTEM.
The system features a special shortcut to help the installer access
the Installer Toolbox quickly. Pressing the lower right corner of
the Home Screen while the system is disarmed will immediately
display a code entry screen. When the correct Installer Code is
Figure 26. Toolbox Screen Two
entered, the system will go directly to the Installer Toolbox.

Installer Toolbox Screen

The Installer Toolbox Screen displays system setup and testing
buttons. Main programming is accessed using the SYSTEM
CONFIGURATION button. The other buttons support system tests
and resetting the Control Panel to its programming default values.

System Configuration Screen

When the SYSTEM CONFIGURATION button is pressed, the Control
Panel will display questions for each programming step. To help
the installer program the Control Panel quickly, the programming Figure 27. Toolbox Screen Three
questions are arranged so that the commonly set values appear
early in the question order.

Figure 28. Installer Toolbox Code Entry Screen

Figure 29. Installer Toolbox Screen

Figure 30. System Configuration Question “Q-1”

13
System Status Icons
The top line of the Control Panel’s display is the status bar that
shows the current system mode, the status of the sensors, and
any current system trouble alerts. Special icons are displayed to
visually show the system’s current condition. STATUS BAR SHOWING
AC POWER IS ON

Figure 31. System Status Bar

AC Power Icon
The AC power icon indicates the Control Panel’s AC line power
status. The icon displays a white plug when the AC power is AC POWER ON AC POWER OFF
present; the icon will display with a red “X” over the white plug
when AC power is absent.
Figure 32. AC Power Icons
Phone Line Failure Icon
If the Control Panel detects that the telephone line is disconnected,
PHONE LINE
the phone line failure icon will be displayed. FAILURE

Figure 33. Phone Line Failure Icon

Sounder Disable Icon

If the system’s internal sounder has been lowered and external SOUNDER
sounder has been disabled by the installer for testing, the sounder DISABLED
disable icon will be displayed. Also flashes to indicate silent arming.

Figure 34. Sounder Disable Icon

Backup Battery Status Icon

If the Control Panel’s backup battery tests low, the low backup LOW BACKUP
BATTERY
battery icon will be displayed.

Figure 35. Backup Battery Status Icon

Test Mode Icon
When the system is being tested in Walk Test Mode, the test mode
icon will be displayed on the status bar. SYSTEM IN
TEST MODE

Figure 36. Test Mode Icon

Touch Screen Keypad Traffic Icon
When the Control Panel is communicating to a touch screen
keypad the up arrow icon is displayed. When a touch screen
COMMUNICATION
keypad communicates to the Control Panel the down arrow icon IN PROCESS
is displayed.

Figure 37. Touch Screen Keypad Traffic Icon

GSM Radio Icon

If the system’s optional GSM radio modem is installed, the GSM OVER-THE-AIR
UPDATE IN
radio icon will be displayed while the Control Panel is receiving PROCESS
over-the-air firmware updates.

Figure 38. GSM Radio Icon

Interior Sensor Open Icon
If an interior sensor is open (or a motion detector has just been
activated) the house icon will be displayed on the status bar. As a INTERIOR
warning, the icon flashes during arming. SENSOR OPEN

Figure 39. Interior Sensor Open Icon

14
Programming Navigation
When the installer is using the System Configuration menus,
the Control Panel will present each programming question
sequentially. Most programming questions have a single numeric
value response or a simple enabled/disabled selection. Some
programming questions have sub-options that can be set. These
sub-options are displayed for the question selected and can be
accessed through navigation keys on the display.

Navigation Arrows & Go To Button

The programming question screens display up, down, left, and
right navigation arrows. They are used to move through the
programming questions and sub-options.
Figure 40. Navigation Arrows & Go To Button
The GO TO button is used to jump directly to a programming
question. Pressing GO TO will prompt the installer for the two-digit
question number to jump to. The GO TO button changes to CANCEL
while waiting for a question number, press CANCEL to back out.

Questions without Sub-options

Most of the programming questions do not have sub-options. They
navigate as follows. Questions without sub-options do not
display a SKIP button.
• The ↑ & ↓ arrows select the next or previous programming question.
• The ← & → arrows choose values for the question or move the cursor left
and right along the white data entry field. Figure 41. Questions without Sub-options
Questions with Sub-options
Some of the programming questions have sub-options. They
navigate as follows. Questions with sub-options display a SKIP
button during the question.
• The SKIP button advances to the next programming question/section.
• The ↑ & ↓ arrows select the next or previous programming sub-question.
• The ← & → arrows choose values for the question or move the cursor left
and right along the white data entry field.
Questions with Data to Enter
Some of the programming questions require entering numeric or
alphabetic data. For devices that can be named, the Control Panel Figure 42. Questions with Sub-options
contains a large vocabulary with words to choose from (see Pg. 19).
• The INSERT button displays a word from the vocabulary. The words can
be scrolled through using the ← & → arrows, or selected by entering their
3-digit index number.
• The (backspace) button moves the cursor to the left, deleting the one
character at a time.
• The (delete) button deletes a character to the right of the cursor, or any
characters that are highlighted.
• The FWD (forward) button highlights the next word in multi-word data fields.
• The BACK button highlights the previous word in multi-word data fields. The
BACK button displays the previous screen in some cases. Figure 43. Questions with Data to Enter
• When the SHIFT button is displayed, pressing it will display alternate
characters on the keypad that can be used for data entry.
Other Buttons Displayed
Depending on the programming question, other buttons may be displayed.
• The ESC (escape) button serves as an “undo”. Pressing ESC restores the
value that was previously stored for the question or sub-question.
• The SUM (summary) button displays a summary of the values stored for the
programming question and sub-options.
• The END button displays a summary of the values stored for the entire
Control Panel memory. Figure 44. Other Buttons Displayed
• The LEARN button is used to set the system to receive a sensor’s serial
number when transmitted during programming the wireless sensors.
• The PASTE button repeats the last sensor serial number entered.
• The EXIT button exits programming.

15
Programming Outline
Each system installed will require programming. Most installations
being performed by the professional alarm installer for a specific
organization will have common values set in every Control Panel
reporting to the same Central Station. Other programming values,
such as the account number and sensor setup, will be unique for
each installation.
Following is an outline to guide the professional alarm installer
through the programming of the Control Panel. Press logo to access
the Installer Toolbox
If you don’t read anything else, read this outline!
Use the following outline in conjunction with this copy of the Figure 45. The Home Screen
Installation and Programming Instructions to guide you through
the installation.
Because of the many programming options available with this
Control Panel, thoroughly reading this manual is very important.
Understanding the Control Panel’s programming structure will help
to save time during each installation.
At this stage, all the wireless and hardwired sensors should be
installed, and the Control Panel should be mounted, connected,
and powered-up.
Installer Toolbox can be
1. Start at the Home Screen. accessed here also

2. Press the logo at the lower right corner of the screen.

(The Installer Toolbox can also be accessed via Figure 46. Toolbox Screen Three
the third screen of the System Toolbox.)
3. Enter the Installer Code (default = 1561) to display the Installer Toolbox.
4. Press SYSTEM CONFIGURATION and begin
programming as described on Page 18.
5. USE THE INSTALLATION LOG SHEET TO RECORD
PROGRAMMED VALUES FOR THE SYSTEM.
6. After setting all the required programming values for the sensors and
the Control Panel, press END, then EXIT, to save the changes.
7. After the Control Panel restarts, press SECURITY, MENU,
TOOLBOX, enter the Master User Code (default = 1111), press
USER MANAGEMENT and setup the user’s codes. Be sure to Figure 47. Installer Toolbox Screen
set a Duress Code as User #8. Press BACK when finished.
8. Press BRIGHTNESS / VOLUME and set the levels for the installation.
The volume setting DOES NOT affect the volume of alarm sounds.
9. Press ➜ to view the second toolbox screen.
10. Press BACKLIGHT TIMEOUT and set the display lighting timeout.
11. Press SET DATE and SET TIME and set the calendar and clock. (If the
GSM module is installed, the date and time are set automatically.)
12. Press the button to return to the Home Screen.
After all setup and programming, refer to the Operation and
User’s Guide for details on operating the system. Check off the Figure 48. System Configuration Question “Q-1”
programmed options for the system in the User’s Guide.
PROGRAMMING QUESTION SIA CP01 DEFAULT RANGE
Be sure to instruct the subscriber on the proper operation of the
system, and leave the User’s Guide at the installation site for Q-1 Wireless Sensor Dialer Delay 30 Seconds On or Off
reference. Q-2 Wired Sensor Dialer Delay 30 Seconds On or Off
Q-5 Exit Delay 60 Seconds 45-120 Seconds
SIA CP01 Defaults
Several system programmable options have the defaults pre-set to Q-6 Entry Delay #1 30 Seconds 30-240 Seconds
provide compliance with the Security Industry Association CP01 Q-7 Entry Delay #2 45 Seconds 30-240 Seconds
Standard. All other system settings and functions that are required Q-10 Call Waiting Disable Code No Default Code 0-6 Digits
to comply with SIA CP01 are permanently programmed into the
Q-20 Swinger Shutdown Count 1 Trip 1-2 Trips
Console and cannot be changed. Refer to the table for each
programmable option that has a required SIA CP01 programming Q-26 Auto Stay Enabled Enabled or Disabled

default. Q-27 Exit Delay Restart Enabled Enabled or Disabled

Q-31 Cancel Time 5 Minutes 6-254 Minutes
Q-32 Cancel Display Enabled Enabled or Disabled
Q-35 Abort Window Dialer Delay 30 Seconds 15 or 45 Seconds

16
Programming Question Table
Q# QUESTION DEFAULT Q# QUESTION DEFAULT
Q-1 Select RF sensor # (01-48) Q-28 Select quick exit (0-1) (1) enabled
Select RF sensor (#) type (00) unused Q-29 Enter periodic test, in days (0-255) 30 days
Varies by RF sensor type Q-31 Enter cancel time, in minutes (5-255) ‡ 5 minutes
Select RF sensor (#) equipment type
(Only shown for some sensor types) Q-32 Select cancel display (0-1) ‡ (1) enabled
Select RF sensor (#) equipment code (0000) other Q-33 Select cross sensor 47-48 (0-1) (0) disabled
Q-1 SUB-QUESTIONS

Enter RF sensor (#) other equipment code (0-9999) 0 (Only shown if other is selected) Q-34 Enter cross sensor timeout, in seconds (10-120) 10 seconds
Enter RF sensor (#) serial number (7 digits) 0000000 Q-35 Select abort window dialer delay (0-2) ‡ (1) 30 seconds
Select RF sensor (#) equipment age (0-1) (0) new Q-36 Select burglary bell cutoff (0-4) (0) 4 minutes
Select RF sensor (#) loop number (1-3) Varies with sensor model selected Q-37 Select fire bell cutoff (0-4) (0) 4 minutes
Select RF sensor (#) dialer delay (0-1) ‡ (1) enabled (except for fire & CO) Q-38 Enter time to detect AC loss, in minutes (0-30) 10 minutes
Construct RF sensor (#) voice descriptor No default Q-39 Select random AC loss report time (0-1) (1) enabled
Select RF sensor (#) reports (0-1) (1) enabled Q-40 Enter CS #2 phone number (0-25 digits) No default
Select RF sensor (#) supervised (0-1) (1) enabled Q-41 Enter CS #2 account number (4 digits) No default
Select RF sensor (#) chime (0-5) (0) disabled Q-42 Select remote control phone (0-3) (3) data and voice
Q-2 Select wired sensor # (1-2) Q-43 Enter installer code (4 digits) 1561
Select wired sensor (#) type (00) unused Q-44 Select lock installer programming (0-2) (0) disabled
Varies by wired sensor type Q-45 Select lock default programming (0-2) (0) default all
Select wired sensor (#) equipment type
(Only shown for some sensor types)
Q-2 SUB-QUESTIONS

Q-46 Select trouble doesn’t sound at night (0-1) ♦ (1) enabled

Enter wired sensor (#) equipment code (0-9999) 0
Q-47 Select trouble resound after holdoff (0-7) (0) disabled
Select wired sensor (#) equipment age (0-1) (0) new
Q-48 Enter download csid (6 digits) 000000
Select wired sensor (#) normal state (0) not used
Q-49 Select programming mode entry reports to CS (0-1) (0) disabled
Select wired sensor (#) dialer delay (0-1) ‡ (1) enabled
Q-50 Select trouble reports to CS (0-1) (1) enabled
Construct wired sensor (#) voice descriptor No default
Q-51 Select manual bypass reports to CS (0-1) (0) disabled
Select wired sensor (#) reports (0-1) (1) enabled
Q-52 Select AC loss reports to CS (0-1) (1) enabled
Select wired sensor (#) chime (0-5) (0) disabled
Q-53 Select system low battery reports to CS (0-1) (1) enabled
Q-3 Select fob # (1-8)
Q-54 Select RF low battery reports to CS (0-1) (1) enabled
Select fob (#) used (0-1) (0) unused
Q-55 Select opening reports to CS (0-1) (0) disabled
Select fob (#) equipment code (0000) (0000) other
Q-56 Select closing reports to CS (0-1) (0) disabled
Q-3 SUB-QUESTIONS

Enter fob (#) other equipment code (0-9999) 0 (Only shown if other is selected)
Q-57 Select alarm restore reports to CS (0-1) (0) disabled
Enter fob (#) serial number (7 digits) 0000000
Q-58 Select trouble restore reports to CS (0-1) (1) enabled
Select fob (#) equipment age (0-1) (0) new
Q-59 Select bypass restores reports to CS (0-1) (0) disabled
Select fob (#) emergency key (0-4) (0) disabled
Q-60 Select AC restore reports to CS (0-1) (1) enabled
Select fob (#) key 2 can disarm (0-1) (1) enabled
Q-61 Select system low battery restore reports to CS (0-1) (1) enabled
Construct fob (#) voice descriptor keyfob #
Q-62 Select RF low battery restores reports to CS (0-1) (1) enabled
Select fob (#) arm no delay (0-1) (0) disabled
Q-63 Select phone fail detect (0-1) (0) disabled
Select fob (#) key 4 output (0-2) (0) disabled
Q-64 Select smart test reports (0-1) (0) disabled
Q-4 Select RF keypad # (1-4)
Q-65 Select RF jam causes trouble (0-1) (0) disabled
Select RF keypad (#) used (0-1) (0) unused
Q-4 SUB-QUESTIONS

Q-66 Select daylight saving (0-1) (1) enabled

Select RF keypad (#) equipment code (0000) other
Q-67 Select daylight saving start month (01-12) (03) March
Enter RF keypad (#) other equipment code (0-9999) 0 (Only shown if other is selected)
Q-68 Select daylight saving start Sunday (1-7) (2) 2nd
Enter RF keypad (#) serial number (7 digits) 0000000
Q-69 Select daylight saving end month (01-12) (11) November
Select RF keypad (#) equipment age (0-1) (0) new
Q-70 Select daylight saving end Sunday (1-7) (1) 1st
Select RF keypad (#) emergency keys (0-1) (1) enabled
Q-71 Select system tamper causes trouble (0-1) (1) enabled
Construct RF keypad (#) voice descriptor keypad #
Q-72 Select quick bypass (0-1) (0) disabled
Q-5 Enter exit delay, in seconds (45-120) ‡ 60 seconds
Q-73 Select disarming keyfob after alarm (alert) (0-1) (0) disabled
Q-6 Enter entry delay 1, in seconds (30-240) ‡ 30 seconds
Q-74 Select keyfob arm / disarm confirmation (0-1) (0) disabled
Q-7 Enter entry delay 2, in seconds (30-240) ‡ 45 seconds
Q-75 Select auto unbypass for manual bypass (0-1) (1) enabled
Q-8 Select dialer (0-1) (0) disabled
Q-76 Select force bypass reports (0-1) (0) disabled
Q-9 Enter dialing prefix (0-4 digits) No default
Q-77 Select event log (0-3) (3) all events
Q-10 Enter call waiting disable code (0-6 digits) ‡ No default
Q-78 Select output (00-10) ‡ (11) follows internal sounder alarm
Q-11 Enter CS #1 phone number (0-25 digits) No default
Q-79 Select Z-Wave feature (0-3) (1) disabled but visible
Q-12 Enter CS #1 account number (4 digits) No default
Q-80 Select Z-Wave switches feature (0-1) (0) disabled
Q-13 Select 2-way voice (0-2) (1) stay on line
Q-81 Select Z-Wave thermostats feature (0-1) (0) disabled
Q-14 Select silent panic/burglary listen only (0-1) (1) enabled
Q-82 Select Z-Wave door locks feature (0-1) (0) disabled
Q-15 Select dialing type (0-1) (0) touch tone
Q-83 Select temperature display units (0-1) (0) degrees Fahrenheit
Q-16 Select police emergency key (0-2) (1) audible
Q-84 Select services require master code (0-1) (0) disabled
Q-17 Select fire emergency key (0-1) (1) audible
Q-85 Select master user access to zwave toolbox (0-1) (0) disabled
Q-18 Select emergency key (0-1) (1) audible
Q-86 Select disable siren after two-way audio (0-1) (0) disabled
Q-19 Select quick arming (0-1) (1) enabled
‡ Default set for SIA CP01 compliance
Q-20 Select swinger shutdown count (1-2) ‡ (1) one trip
♦ For UL985 Installations, this feature must be disabled
Q-21 Select siren supervision time (0-3) (0) disabled
Q-22 Enter CS lack of usage notification time (0-255) 7 Days
Q-23 Enter radio modem network failure time (0-255) 30 minutes
Q-24 Select radio modem network failure causes trouble (0-1) (1) enabled
Q-25 Select radio modem network failure reports (0-1) (1) enabled
Q-26 Select auto stay (0-1) ‡ (1) enabled
Q-27 Select exit delay restart (0-1) ‡ (1) enabled

17
System Sensor Types
Each sensor (wireless or wired) installed in the system is (06) 24-hour Silent Alarm
programmed to a specific sensor number and sensor type (zone). This sensor type is active independent of the system arming status. The code
The sensor number identifies the specific sensor when it is for silent panic is sent to the Central Station, but for safety, there are no visual or
displayed on the Control Panel, recorded in the event log, or audible indications locally that this sensor type has been triggered.
reported to the Central Station. This allows pin-point information
(07) 24-hour Audible Alarm
about any sensor in the system.
This sensor type is continuously armed 24-hours a day. A sensor programmed to
The sensor type determines how and when the Control Panel this type will trigger a local alarm and the bell output regardless of the mode the
responds to signals from the sensor. Some sensors are armed system is in. Typical use would be an audible panic alarm.
all the time, others are armed only in certain arming levels, some
cause Central Station reports any time they are activated. The (08) 24-hour Auxiliary Alarm
sensor’s type, along with other programming options, determine This sensor type is continuously armed 24-hours a day. A sensor programmed
this. to this type will trigger an alarm regardless of the mode the system is in. The bell
output will not activate, but the local sounder will continue until it’s acknowledged
Sensor Types (Zones) at the Control Panel. Typical use would be for a monitoring device such as a flood
(00) Unused or temperature sensor. There is no timeout for the internal sounder, it will continue
This is the setting for unused sensor numbers that do not have a sensor until a User Code is entered.
programmed into them. No system action occurs at any time from this sensor
(09) 24-hour Fire †
type.
This sensor type is continuously armed 24-hours a day. A sensor programmed
(01) Exit/Entry 1 to this type will trigger the local alarm fire sounder and the bell output regardless
This sensor type is reserved for doors that are used for exit and entry of the of the mode the system is in. Typical use would be for wireless smoke detectors.
protected premises. When the system is armed in the Away Mode or Stay Mode, This sensor type is always active and cannot be bypassed.
the Exit Delay timer starts. There is an Exit Delay regardless of whether the
(10) Interior with Delay
system is armed in Stay Mode or Away Mode. When the Exit Delay timer expires,
This sensor type operates as a delayed sensor when the system is armed in the
the system is fully armed.
Away Mode, and when triggered, will start the Entry Delay #1 timer. If the system
With the system fully armed, when this type of sensor is triggered, the Entry is armed in Away Mode with no Entry Delay (armed instant), this sensor type will
Delay #1 timer starts. The system must be disarmed before the Entry Delay #1 trigger an instant alarm.
time expires, or an alarm will occur.
If the system is armed in Stay Mode (or Stay Mode with no Entry Delay), this
If the Entry Delay is turned off during arming, the exit/entry delay sensors will act sensor type will be bypassed.
as non-delayed instant sensors at the end of Exit Delay.
(14) 24-hour Carbon Monoxide †
(02) Exit/Entry 2 This sensor type is continuously armed 24-hours a day. A sensor programmed to
This sensor type operates the same as the Exit/Entry 1 sensor type except it will this type will trigger the local alarm pulse sounder and the bell output regardless
start the Entry Delay #2 timer. This provides a method of having a longer Entry of the mode the system is in. Typical use would be for wireless carbon monoxide
Delay on certain openings, such as a garage door, to provide the user more time detectors. This sensor type is always active and cannot be bypassed.
to disarm the system.
(16) 24-hour Fire with Verification †
(03) Perimeter This sensor type is continuously armed 24-hours a day. A sensor programmed to
This sensor type is for perimeter doors and windows that will not be used to enter this type can trigger the local alarm fire sounder and the bell output regardless
or exit the protected premises while the system is armed. of the mode the system is in. Typical use would be for wireless smoke detectors.
An instant alarm will occur when this type of sensor is triggered with the system This sensor type is always active and cannot be bypassed.
armed in either the Stay Mode or Away Mode. For verification, this sensor type must be violated twice in two minutes, or remain
violated for 30 seconds. If any other fire sensor (verified sensor type or not)
(04) Interior Follower violates within two minutes, both sensors will cause a fire alarm.
This sensor type is for interior sensors such as motion detectors, mat switches,
interior doors, and other sensors that detect human presence inside the protected (23) No Response Type
premises. This sensor type is a special zone that can be monitored for activity or inactivity
This type of sensor is called a “follower” due to its action when the system is by the Central Station. It does not affect security system status.
armed in the Away Mode. After the Exit Delay expires and the system is armed, if
an interior follower sensor is triggered, an instant alarm will occur. If an exit/entry (24) Silent Burglary
delay sensor is triggered first, the interior follower sensor will also be delayed. This sensor type is for silent triggering the burglary alarm with perimeter doors
and windows that will not be used to enter or exit the protected premises while
Interior follower sensors are always bypassed and not active when the system is the system is armed. The Control Panel’s sounder and the bell output will not
armed in Stay Mode. This allows the premises to be occupied while still protecting activate.
the perimeter.
An instant silent alarm will occur when this type of sensor is triggered with the
(05) Day Zone system armed in either the Stay Mode or Away Mode.
This sensor type is the same as a perimeter zone, except when the system is
disarmed, a violation displays a trouble alert on the Console’s display. † Indicates Sensor types that are not allowed for hardwired
Common uses for this sensor type are protection of sensitive areas that require loops.
notification and possibly a Central Station trouble report, but not an alarm when
the system is disarmed.

18
System Vocabulary Table
# WORD # WORD # WORD # WORD
002 ABORT 066 ELEVEN 130 LIGHT 194 SET
003 AC 067 EMERGENCY 131 LIGHTS 195 SEVEN
004 ACCESS 068 ENTER 132 LIQUOR 196 SEVENTEEN
005 ALARM 069 ENTRANCE 133 LIVING 197 SEVENTY
006 AND 070 ENTRY 134 LOADING 198 SHED
007 ANNOUNCEMENT 071 ERROR 135 LOCK 199 SHOP
008 AREA 072 EXERCISE 136 LOFT 200 SIDE
009 ARM 073 EXIT 137 LOW 201 SILENT
010 ARMED 074 EXIT NOW 138 MAIN 202 SIREN
011 ARMING 075 EXTERIOR 139 MAINTENANCE 203 SIX
012 AT 076 EXTERNAL 140 MASTER 204 SIXTEEN
013 ATTIC 077 FAILURE 141 MEDICAL 205 SIXTY
014 AUDIO 078 FAMILY 142 MEDICINE 206 SKYLIGHT
015 AUTO 079 FAN 143 MENU 207 SLIDING
016 AUTOMATION 080 FIFTEEN 144 MIDDLE 208 SMOKE
017 AUXILIARY 081 FIFTY 145 MONITOR 209 SOUNDER
018 AWAY 082 FIRE 146 MOTION 210 SOUTH
019 BABY’S 083 FIRE ALERT 147 MOTION DETECTOR 211 SPACE
020 BACK 084 FIRE DETECTOR 148 MUD 212 SPARE
021 BASEMENT 085 FIRST 149 NINE 213 STAIRS
022 BATHROOM 086 FIVE 150 NINETEEN 214 STAR
023 BATTERY 087 FLOOD 151 NINETY 215 STATUS
024 BEDROOM 088 FLOOR 152 NORTH 216 STAY
025 BONUS 089 FLUID 153 NOT 217 STOP
026 BREAK 090 FOIL 154 NOT READY 218 STORAGE
027 BUTTON 091 FOR 155 NO DELAY 219 STUDY
028 BYPASS 092 FORTY 156 NO ENTRY DELAY 220 SUMP
029 BYPASSED 093 FOUR 157 NURSERY 221 SUPERVISION
030 CABINET 094 FOURTEEN 158 OFF 222 SYSTEM
031 CANCEL 095 FOURTH 159 OFFICE 223 TAMPER
032 CARBON MONOXIDE 096 FREEZE 160 ON 224 TEMPERATURE
033 CELLAR 097 FREEZER 161 ONE 225 TEN
034 CELLULAR 098 FRONT 162 ONE HUNDRED 226 TERMINATED
035 CELL RADIO 099 FURNACE 163 OUTPUT 227 THERMOSTAT
036 CENTER 100 GAME 164 OUTSIDE 228 THIRD
037 CHECK 101 GARAGE 165 PANEL 229 THIRTEEN
038 CHEST 102 GAS 166 PANIC 230 THIRTY
039 CHILDREN’S 103 GLASS 167 PANTRY 231 THREE
040 CHIME 104 GLASS BREAK 168 PATIO 232 TO
041 CLOSET 105 GUEST 169 PERIMETER 233 TOOL
042 CODE 106 GUN 170 PHONE LINE 234 TRANSMITTED
043 COMMUNICATIONS 107 HALL 171 PLAY 235 TRANSMITTER
044 COMPUTER 108 HALLWAY 172 POLICE 236 TROUBLE
045 CONTROL 109 HANGING 173 POOL 237 TURN
046 COOL 110 HANG UP 174 POUND 238 TWELVE
047 CRAWL 111 HEAT 175 POWER 239 TWENTY
048 CURRENT 112 HIGH 176 PRESS 240 TWO
049 DAY 113 HOME 177 PREVIOUS 241 UNLOCK
050 DEGREES 114 HOUSE 178 PUMP 242 UPPER
051 DEN 115 ICE 179 RADIO 243 UPSTAIRS
052 DETECTOR 116 INSIDE 180 READY 244 USER
053 DIM 117 INSTANT 181 REAR 245 UTILITY
054 DINING 118 INTERIOR 182 RELAY 246 VALVE
055 DISARM 119 INTRUSION 183 REMOTE 247 VOICE
056 DISARMED 120 IS 184 REPEAT 248 WALL
057 DOCK 121 KEY 185 RF JAM 249 WATER
058 DOOR 122 KEYFOB 186 RIGHT 250 WEST
059 DOWNSTAIRS 123 KEYPAD 187 ROOM 251 WINDOW
060 DRIVEWAY 124 KIDS 188 SAFE 252 WIRELESS
061 EAST 125 KITCHEN 189 SECOND 253 YARD
062 EIGHT 126 LAUNDRY 190 SECURITY 254 ZERO
063 EIGHTEEN 127 LEFT 191 SENSOR 255 ZONE
064 EIGHTY 128 LEVEL 192 SENSORS
065 ELECTRIC 129 LIBRARY 193 SESSION

SELECT RF SENSOR ENTER ON KEYPAD OR PRESS

SUPERVISED
OR

PRESS FOR NEXT OPTION TO SELECT FROM LIST

ENTER ON KEYPAD OR PRESS

SELECT RF SENSOR
CHIME OR
TO SELECT FROM LIST
edit
PRESS TO FINISH FOR THIS SENSOR, THEN next FOR NEXT SENSOR, OR skip FOR Q2

Figure 49. RF Sensor Programming Outline

21
Installer Programming
RF Sensor Programming Steps Select RF sensor (#) equipment code
DEFAULT: (0000) other
Q-1 Select RF sensor # (01-48) The equipment code is a 4-digit code that is assigned to the model of sensor
Up to 48 wireless RF sensors can be used with each Control Panel. The options being used. The Control Panel will display a list of sensor models and their
for each sensor are programmed with sub-option questions. associated 4-digit equipment code.
• Begin by entering the RF sensor number or • Select the model of RF sensor being programmed for this
select it using the ← or → arrows. sensor number using the ← or → arrows, or enter the
• After selecting the sensor number, program the sensor details by equipment code number directly on the keypad.
using the ↑ and ↓ arrows to select each of the sub-options. • Select “(0000) other” if the sensor model is not shown on the list. The
✓ NOTE: To skip RF sensor programming, press SKIP to jump from equipment code for the sensor can be entered using the next sub-question.
question Q-1 to question Q-2 (wired sensor programming).
SENSOR EQUIPMENT CODES
(0000) other
Select RF sensor (#) type
DEFAULT: Unused (00) (0862) DW10-345 thin door/window contact
Each RF sensor needs to be assigned to a sensor type. The sensor type (0863) DW20R-345 recessed door contact
determines how and when the Control Panel responds to signals from the (0869) PIR1-345 PIR with pet immunity
sensor.
(0864) GB1-345 glass break detector
Use this step to assign the sensor to a sensor type (zone).
(0895) SMKT2-345 GE smoke/heat detector (USA/Canada)
• Select the sensor type that matches the sensor’s function using the
← or → arrows, or enter the sensor type number directly on the keypad. (1058) SMKT3-345 2gig smoke detector
(0872) SMKE1-345 smoke detector (USA)
SENSOR TYPES
(0871) SMKE1-345C smoke detector (Canada)
(00) unused
(0868) PANIC1-345 panic button remote
(01) exit/entry 1
(0860) CO1-345 CO detector (USA)
(02) exit/entry 2
(0859) CO1-345C CO detector (Canada)
(03) perimeter
(1026) CO3-345 2gig CO detector (USA/Canada)
(04) interior follower
(0873) TAKE-345 takeover module
(05) day zone
(0637) HW D/W “5816”
(06) 24-hour silent alarm
(0470) HW R-D/W “5818MNL”
(07) 24-hour audible alarm
(0533) HW PIR “5890”
(08) 24-hour auxiliary alarm
(0530) HW PIR “5894PI”
(09) 24-hour fire
(0519) HW Glass Break “5853”
(10) interior with delay
(0589) HW Smoke “5808W3”
(14) 24-hour carbon monoxide
(0557) HW Heat Sensor “5809”
(16) 24-hour fire with verification
(0624) HW Flood Sensor “5821”
(23) no response type
(0491) HW Panic Pendant “5802MN2”
(24) silent burglary
(0655) Existing door/window contact
(0609) Existing motion detector
Select RF sensor (#) equipment type
(0475) Existing glass break detector
DEFAULT: Varies by RF sensor type
✓ NOTE: This question is only displayed when certain sensor types are selected. (0616) Existing smoke detector
The equipment type selection will affect the sensor’s extended reporting code. (0692) Existing CO detector
The following sensor types require equipment type selection:
(0708) Existing heat sensor
SENSOR TYPE EQUIPMENT TYPES AVAILABLE (0556) Existing flood/temp sensor
(04) interior follower (1) = motion (2) = contact (1061) GARAGE01 Resolution Products tilt sensor
(06) 24-hour silent alarm (1) = contact (11) = emergency
(07) 24-hour audible alarm (1) = contact (11) = emergency Enter RF sensor (#) other equipment code (0-9999)
(1) = contact (6) = freeze (8) = water DEFAULT: 0
(08) 24-hour auxiliary alarm
(10) = temperature (11) = emergency ✓ NOTE: This question is only displayed if “(0000) other”
is selected for a sensor’s equipment code.
(10) interior with delay (1) = motion (2) = contact
The equipment code is a 4-digit code that is assigned to the model of sensor being
(23) no response type (1) = contact (2) = motion used. If new equipment becomes available, the new equipment code should be
• Select the equipment type that matches the sensor equipment using the entered here if the new equipment is not listed in the Sensor Equipment Codes
← or → arrows, or enter the equipment type number directly on the keypad. table above.
• Enter the equipment code number directly on the keypad for the
RF sensor. (Enter “0” if the new equipment code is unknown.)

22
Installer Programming
Enter RF sensor (#) serial number (7 digits) Construct RF sensor (#) voice descriptor
DEFAULT: 0000000 DEFAULT: No default
RF sensor serial numbers can be manually entered or learned from the sensor. The voice descriptors are the words the Control Panel will announce for this RF
• For manual entry, enter the sensor number that was logged for the sensor sensor if this sensor is programmed for voice annunciation. Up to five words are
being programmed. Use the SHIFT button to access alpha characters. allowed.
• For automatic entry, press SHIFT, then press LEARN. The • Press INSERT to place a word from the vocabulary into the data entry field.
Control Panel will wait for a sensor transmission. Trigger • Use the ← or → arrows to scroll through the words, or enter the
the sensor being programmed and the Control Panel will word’s 3-digit index number (see vocabulary table on Page 19).
beep four times and learn the sensor’s serial number. • Press INSERT again for the next word. Up to five words are allowed.
If the sensor being learned is already in memory, the Control Panel will display a
• To move between words, press the FWD and BACK buttons.
sensor learning failure screen when the programming changes are being saved.
• To remove a word, press DELETE.
For certain sensors with more than two loops, the tamper switch must be used to
send a signal to the Control Panel during sensor learning. First press of tamper
switch will learn as Loop #1, the second press of tamper switch will learn as Select RF sensor (#) reports (0-1)
Loop #2, the third press of tamper switch will learn as Loop #3. Wait 15 seconds DEFAULT: Enabled (1)
between each press of the tamper switch. The programmed loop number of RF sensors can trigger a report to the Central Station or not.
the sensor in the Control Panel may need changing to suit the operation of the
• The default (1) enables reporting for this RF sensor number.
device. See the Installation Instructions of the sensor for details.
• To prevent reporting for this RF sensor number, select disabled (0).

Select RF sensor (#) equipment age (0-1) Select RF sensor (#) supervised (0-1)
DEFAULT: New (0) DEFAULT: Enabled (1)
The Control Panel can be used with new or existing RF sensors.
When a sensor is set to supervised, the Control Panel will expect regular timed
• If this RF sensor is new for the installation, leave the default of new (0). signals from this sensor or else a sensor supervisory trouble alert will occur.
• If this RF sensor is already installed, select existing (1). • The default (1) allows supervision for this RF sensor.
✓ NOTE: If the RF sensor has more than one loop and is being • To turn off supervision for this RF sensor, select disabled (0).
programmed into multiple sensor numbers to support the loops,
set only one loop as “new” and the other loops as “existing”. This ✓ NOTE: Portable sensors such as panic buttons should not be set as
will prevent incorrect inventory of the installed sensors. supervised if the sensor will be removed from the premises at times.

Select RF sensor (#) loop number (1-3) Select RF sensor (#) chime (0-5)
DEFAULT: Varies with sensor model selected DEFAULT: Disabled (0)
2GIG-DW10 door/window sensors have two inputs: an internal magnetic contact Each RF sensor can be set to sound a “ding-dong” chime and/or sound its voice
and an external normally closed hardwired input. Either or both sensor inputs can descriptor when the sensor is triggered. This step determines the initial setting
be used. Some sensors have three loop inputs. for the sensor. The end user can change the chime setting for sensors using
CHIME SETUP in the User Toolbox.
When using both the internal magnetic contact AND the external input,
THE MAGNETIC CONTACT AND THE EXTERNAL CONTACT NEED TO • The default (0) disables the chime for this RF sensor.
BE ASSIGNED A DIFFERENT RF SENSOR NUMBER. BOTH SENSOR • If a chime and/or voice is required for this RF sensor,
NUMBERS WILL SHARE THE SAME SENSOR SERIAL NUMBER. choose one of the other chime options:
• When programming the sensor to use the built-in RF SENSOR CHIME
magnetic contact, set the loop number to (2). (0) disabled
• When programming the sensor to use its hardwired
(1) voice only
input, set the loop number as (1).
• When programming a 3-loop sensor to use an (2) voice with ding-dong #1
additional input, set the loop number as (3). (3) ding-dong #2
• When entering the sensor number for the sensor’s loop two (4) voice with ding-dong #2
or three, the PASTE button can be used to recall the last
(5) ding-dong #1
programmed sensor’s serial number. (The sensor number
will be filled in automatically if LEARN is used.)

Select RF sensor (#) dialer delay (0-1)

DEFAULT: Enabled (1) (Required SIA CP01 Default)
RF sensors can trigger the communicator immediately or after a delay. The delay
time is set by the abort window dialer delay programming question Q-35 (the
default delay is 30 seconds).
• The default (1) causes delayed dialing for this RF sensor number.
• For immediate dialing for this RF sensor number, select disabled (0).
✓ NOTE: This setting for CO and smoke detectors is automatically set to
disabled (0), and this sub-question is skipped for these sensor types.
✓ NOTE: This default can be changed without affecting SIA CP01 compliance.

23
Installer Programming
Wired Sensor Programming
Wired Sensor Programming Outline
The Control Panel can be programmed with up to two wired
sensors. The wired sensors are hardwired contact loops connected WIRED SENSOR PROGRAMMING (Q-2) OUTLINE
to the loop input terminals on the Control Panel’s terminal strip.
✓ NOTE: WIRED SENSORS CANNOT BE USED FOR A STEP DOWN SELECT OPTION WITH
THROUGH OPTIONS THESE KEYS
CO OR FIRE SENSOR LOOP!!!
Programming the wired sensors into the Control Panel involves
selecting the sensor number (1 or 2), selecting the wired sensor
ENTER ON KEYPAD OR PRESS
type, setting the equipment code, loop type (open, closed, or
SELECT WIRED SENSOR #
end-of-line resistor), and selecting the other options for the OR
sensor.
TO SELECT FROM LIST
• Wired sensors #1 & #2 report as system sensors #49 & #50 PRESS FOR NEXT OPTION OR PRESS SKIP TO JUMP TO Q-3

WIRED SENSOR REPORTING CODES ENTER ON KEYPAD OR PRESS

SELECT WIRED
Wired sensor #1 Reports as sensor #49 SENSOR TYPE
OR
Wired sensor #2 Reports as sensor #50
PRESS FOR NEXT OPTION
TO SELECT FROM LIST
Refer to Figure 52 for an outline of the steps required to program
wired sensors into the Control Panel. The options that can be set SELECT WIRED SENSOR ENTER ON KEYPAD OR PRESS
for each wired sensor are: EQUIPMENT TYPE
(ONLY FOR SOME SENSOR TYPES) OR
• Wired Sensor Number — Sensor number 1 or 2
PRESS FOR NEXT OPTION
TO SELECT FROM LIST
• Wired Sensor Type — Exit/entry, perimeter, interior, etc.
• Wired Sensor Equipment Type — Certain
ENTER WIRED SENSOR
sensor types will ask for equipment type EQUIPMENT CODE
ENTER ON KEYPAD
• Wired Sensor Equipment Code — 4-digit
equipment code that matches installed sensor PRESS FOR NEXT OPTION

• Wired Sensor Equipment Age —

Q-2 SUB-QUESTIONS

ENTER ON KEYPAD OR PRESS

New install or existing sensor SELECT WIRED SENSOR
EQUIPMENT AGE
• Wired Sensor Normal State — normally OR
open, closed, or end-of-line resistor loop TO SELECT FROM LIST
PRESS FOR NEXT OPTION
• Wired Sensor Dialer Delay — Delayed or
instant communicator reports for the sensor ENTER ON KEYPAD OR PRESS
SELECT WIRED SENSOR
(delay time is set by dialer abort window) NORMAL STATE
OR
• Wired Sensor Voice Descriptor — Name
assigned to the sensor PRESS FOR NEXT OPTION
TO SELECT FROM LIST

• Wired Sensor Reports — Communicator reports

ENTER ON KEYPAD OR PRESS
or no communicator reports for the sensor SELECT WIRED SENSOR
DIALER DELAY
• Wired Sensor Chime — Select voice announcement OR
and chime options for the sensor TO SELECT FROM LIST
PRESS FOR NEXT OPTION
Wired Sensor Summary Screen
After setting all the options for a sensor, the wired sensor PRESS insert FOR EACH WORD
CONSTRUCT WIRED SENSOR
summary screen is displayed. The screen can also be displayed VOICE DESCRIPTOR ENTER ON KEYPAD OR PRESS
for programmed sensors during wired sensor program editing by OR
pressing the SUM button.
PRESS FOR NEXT OPTION TO SELECT FROM LIST
• The ← and → arrow buttons step through the wired sensor numbers.
• The EDIT CURRENT and EDIT NEXT buttons return to sensor SELECT WIRED SENSOR ENTER ON KEYPAD OR PRESS
programming. REPORTS
OR
• Pressing SKIP goes to question Q-3 (key fob programming).
PRESS FOR NEXT OPTION TO SELECT FROM LIST

ENTER ON KEYPAD OR PRESS

SELECT WIRED SENSOR
CHIME
OR

TO SELECT FROM LIST

edit
PRESS TO FINISH FOR THIS SENSOR, THEN next FOR NEXT SENSOR, OR skip FOR Q3

Figure 51. Wired Sensor Summary Screen Figure 52. Wired Sensor Programming Outline
24
Installer Programming
Wired Sensor Programming Steps Select wired sensor (#) normal state
DEFAULT: Not used (0)
Q-2 Select wired sensor # (1-2) The two hardwired loops can be wired for normally open (N/O) or normally closed
Two hardwired loops can be used as sensors with each Control Panel. The (N/C) contacts, or for end-of-line (EOL) resistor.
options for each wired sensor are programmed with sub-option questions. • The default (0) disables this wired sensor.
• Begin by entering the wired sensor number or • To use this wired sensor, select the way the loop is wired:
select it using the ← or → arrows.
• After selecting the wired sensor number, program the wired sensor WIRED SENSOR NORMAL STATE
details by using the ↑ and ↓ arrows to select each of the sub-options. (0) not used
✓ NOTE: To skip wired sensor programming, press SKIP to jump
(1) closed
from question Q-2 to question Q-3 (RF key fob programming).
(2) open

Select wired sensor (#) type (3) end-of-line resistor

DEFAULT: Unused (00)

Each wired sensor needs to be assigned to a sensor type. Select wired sensor (#) dialer delay (0-1)
• Select the sensor type that matches the wired sensor’s function using the DEFAULT: Enabled (1) (Required SIA CP01 Default)
← or → arrows or enter the sensor type number directly on the keypad. Wired sensors can trigger the communicator immediately or after a delay. The
delay time is set by the abort window dialer delay programming question Q-35
SENSOR TYPES
(the default delay is 30 seconds).
(00) unused
• The default (1) causes delayed dialing for this wired sensor number.
(01) exit/entry 1
(02) exit/entry 2 • For immediate dialing for this wired sensor number, select disabled (0).
(03) perimeter ✓ NOTE: This default can be changed without affecting SIA CP01 compliance.
(04) interior follower
(05) day zone Construct wired sensor (#) voice descriptor
(06) 24-hour silent alarm DEFAULT: No default
(07) 24-hour audible alarm The voice descriptors are the words the Control Panel will announce for this wired
(08) 24-hour auxiliary alarm sensor if this wired sensor is programmed for voice annunciation. Up to five words
(10) interior with delay are allowed.
(23) no response type • Press INSERT to place a word from the vocabulary into the data entry field.
(24) silent burglary • Use the ← or → arrows to scroll through the words, or enter the
word’s 3-digit index number (see vocabulary table on Page 19).
Select wired sensor (#) equipment type • Press INSERT again for the next word. Up to five words are allowed.
DEFAULT: Varies by wired sensor type • To move between words, press the FWD and BACK buttons.
✓ NOTE: This question is only displayed when certain sensor types are selected. • To remove a word, press DELETE.
The equipment type selection will affect the sensor’s extended reporting code.
The following sensor types require equipment type selection: Select wired sensor (#) reports (0-1)
SENSOR TYPE EQUIPMENT TYPES AVAILABLE DEFAULT: Enabled (1)
(04) interior follower (1) = contact (2) = motion Wired sensors can trigger a report to the Central Station or not.
(06) 24-hour silent alarm (1) = contact (11) = emergency
• The default (1) enables reporting for this wired sensor number.
(07) 24-hour audible alarm (1) = contact (11) = emergency
(1) = contact (6) = freeze (8) = water • To prevent reporting for this wired sensor number, select disabled (0).
(08) 24-hour auxiliary alarm
(10) = temperature (11) = emergency
(10) interior with delay (1) = contact (2) = motion Select wired sensor (#) chime (0-5)
(23) no response type (1) = contact (2) = motion
DEFAULT: (0) Disabled
• Select the equipment type that matches the sensor equipment using the Each wired sensor can be set to sound a “ding-dong” chime and/or sound its
← or → arrows, or enter the equipment type number directly on the keypad. voice descriptor when the sensor is triggered.
✓ NOTE: This Control Panel does not provide auxiliary accessory output power.
Connecting a hardwire PIR using equipment type “motion” will require • The default (0) disables the chime for this wired sensor.
an external stand-alone battery backed-up power supply for the PIR. • If a chime and/or voice is required for this wired sensor,
choose one of the other chime options:
Select wired sensor (#) equipment code (0-9999) WIRED SENSOR CHIME
DEFAULT: (0) (0) disabled
The wired sensor equipment code defines the sensor’s manufacturer and type.
(1) voice only
• Enter the 4-digit equipment code for the sensor.
(2) voice with ding-dong #1
(3) ding-dong #2
Select wired sensor (#) equipment age (0-1)
DEFAULT: New (0) (4) voice with ding-dong #2
The Control Panel can be used with new or existing wired sensors. (5) ding-dong #1
• If this wired sensor is new for the installation, leave the default of new (0).
• If this wired sensor is already installed, select existing (1).

25
Installer Programming
RF Key Fob Programming KEY FOB PROGRAMMING (Q-3) OUTLINE
RF Key Fob Programming Outline STEP DOWN SELECT OPTION WITH
THROUGH OPTIONS THESE KEYS
The Control Panel can be programmed with up to eight RF remote
control key fobs.
ENTER ON KEYPAD OR PRESS
Programming the RF key fobs into the Control Panel involves
selecting the sensor number for a particular device, setting or SELECT KEY FOB #
OR
learning the RF key fob’s serial number, and selecting the other
options for the sensor. TO SELECT FROM LIST
PRESS FOR NEXT OPTION OR PRESS SKIP TO JUMP TO Q-4
• RF key fobs #1 - #8 report as system sensors #51 - #58
for opening/closing, emergency, and low battery reports. ENTER ON KEYPAD OR PRESS
SELECT KEY FOB
USED
RF KEY FOB REPORTING CODES OR

RF key fob #1 Reports as sensor #51 TO SELECT FROM LIST

PRESS FOR NEXT OPTION
RF key fob #2 Reports as sensor #52
ENTER ON KEYPAD OR PRESS
RF key fob #3 Reports as sensor #53 SELECT KEY FOB
EQUIPMENT CODE
RF key fob #4 Reports as sensor #54 OR

RF key fob #5 Reports as sensor #55 TO SELECT FROM LIST

PRESS FOR NEXT OPTION
RF key fob #6 Reports as sensor #56
RF key fob #7 Reports as sensor #57 ENTER KEY FOB
OTHER EQUIPMENT CODE
RF key fob #8 Reports as sensor #58 (ONLY FOR "OTHER" EQUIPMENT) ENTER ON KEYPAD

Refer to Figure 54 for an outline of the steps required to program

PRESS FOR NEXT OPTION
RF key fobs into the Control Panel. The options that can be set for
each RF key fob are: ENTER ON KEYPAD OR PRESS
ENTER KEY FOB
• Key Fob Number — Key fob number 1-8 SERIAL NUMBER
shift THEN learn
• Key Fob Used — Key fob used or not
AND SEND SIGNAL FROM SENSOR
• Key Fob Equipment Code — Key fob model PRESS FOR NEXT OPTION

• Key Fob Other Equipment Code — Enter special

ENTER ON KEYPAD OR PRESS
equipment code (only shown for key fobs set as “other”) SELECT KEY FOB
EQUIPMENT AGE
• Key Fob Serial # — Serial number labeled on key OR
Q-3 SUB-QUESTIONS

fob; hand enter or “learn” by sending signal

PRESS FOR NEXT OPTION
TO SELECT FROM LIST
• Key Fob Equipment Age — New unit or existing key fob
• Key Fob Emergency Key — Choose ENTER ON KEYPAD OR PRESS
function of double-press on top buttons SELECT KEY FOB
EMERGENCY KEY OR
• Key Fob Can Disarm — Choose whether a
key fob is allowed to disarm the system TO SELECT FROM LIST
PRESS FOR NEXT OPTION
• Key Fob Voice Descriptor — Name assigned to the key fob
• Key Fob Arm No Delay — Choose if key fob ENTER ON KEYPAD OR PRESS
SELECT KEY FOB
will arm instantly without an Exit Delay KEY 2 CAN DISARM
OR
• Key Fob Key 4 Output — Select action
for key fob auxiliary button TO SELECT FROM LIST
PRESS FOR NEXT OPTION
RF Key Fob Summary Screen
PRESS insert FOR EACH WORD
After setting all the options for a sensor, the key fob summary screen CONSTRUCT KEY FOB
is displayed. The screen can also be displayed for programmed key VOICE DESCRIPTOR ENTER ON KEYPAD OR PRESS
fobs during key fob program editing by pressing the SUM button. OR
• The ← and → arrow buttons step through the key fob numbers. PRESS FOR NEXT OPTION TO SELECT FROM LIST
• The EDIT CURRENT and EDIT NEXT buttons return to key fob
ENTER ON KEYPAD OR PRESS
programming. SELECT KEY FOB
ARM NO DELAY
• Pressing SKIP goes to question Q-4 (RF keypad programming). OR

PRESS FOR NEXT OPTION TO SELECT FROM LIST

ENTER ON KEYPAD OR PRESS

SELECT KEY FOB
KEY 4 OUTPUT
OR

TO SELECT FROM LIST

edit
PRESS TO FINISH FOR THIS SENSOR, THEN next FOR NEXT SENSOR, OR skip FOR Q4

Figure 53. Key Fob Summary Screen Figure 54. Key Fob Programming Outline
26
Installer Programming
RF Key Fob Programming Steps Select fob (#) emergency key (0-4)
DEFAULT: Disabled (0)
Q-3 Select fob # (1-8) Pressing the and buttons on a key fob at the same time for five
Up to eight wireless 4-button key fobs can be used with each Control Panel. Key seconds can trigger an emergency alarm.
fobs reports as sensors 51-58. The options for each fob are programmed with • The default (0) disables the emergency function for this fob.
sub-option questions. • To enable the emergency function for this fob, select one of the four options:
• Begin by entering the fob number or select it using the ← or → arrows. FOB EMERGENCY KEY FUNCTION
• Program the key fobs by using ↑ and ↓ arrows to select the sub-options.
(0) disabled
✓ NOTE: To skip RF key fob programming, press SKIP to jump from
question Q-3 to question Q-4 (RF keypad programming). (1) auxiliary alarm
(2) audible alarm
Select fob (#) used (0-1) (3) silent panic
DEFAULT: Unused (0) (4) fire
Key fobs can be used with the Control Panel or not.
• The default (0) sets all key fobs as unused (0). Select fob (#) key 2 can disarm (0-1)
• To enable programming for this key fob, select used (1).
DEFAULT: Enabled (1)
Key fobs can be set to allow disarming the Control Panel with the fob’s
Select key fob (#) equipment code (0-9999) button or not. If using a key fob as a stationary wall fob, it can be set to prevent
DEFAULT: (0000) other someone from using it to disarm the system.
The key fob equipment code defines the sensor’s manufacturer and type. • The default (1) allows this fob to disarm the system.
• The default is (0000) other. • To not allow this fob to disarm the system, select disabled (0).
• Select (0866) KEY1-345 4-button keyfob remote
for a 2GIG-KEY1 key fob remote. Construct fob (#) voice descriptor
• Select (0577) Existing keyfob remote for an existing key fob remote. DEFAULT: Keyfob (#)
✓ NOTE: Only 2GIG-KEY1 key fobs can be used with this system. The voice descriptor is the words the Control Panel will use for this fob for low
battery announcements and log entries. Up to five words are allowed.
Enter key fob (#) other equipment code (0-9999) • Press INSERT to place a word from the vocabulary into the data entry field.
DEFAULT: 0 • Use the ← or → arrows to scroll through the words,
✓ NOTE: This question is only displayed if “(0000) other” or enter the word’s 3-digit index number.
is selected for a key fob’s equipment code. • Press INSERT again for the next word. Up to five words are allowed.
The equipment code is a 4-digit code that is assigned to the model of key fob • To remove a word, press DELETE.
being used.
• Enter the equipment code number for the key fob. Select fob (#) arm no delay (0-1)
DEFAULT: Disabled (0)
Enter fob (#) serial number (7 digits) Key fobs can be set to arm the Control Panel with or without an Entry Delay.
DEFAULT: 0000000 • The default (0) sets this fob to arm the system with an Entry Delay.
Key fob serial numbers can be manually entered or learned from the fob.
• To set this fob to arm the system without an Entry Delay, select enabled (1).
• For manual entry, enter the fob number that was logged for the fob being
programmed. Use the SHIFT button to access alpha characters.
Select fob (#) key 4 output (0-2)
• For automatic entry, press SHIFT, then press LEARN. The Control
Panel will wait for a fob transmission. Trigger the fob being programmed
DEFAULT: Disabled (0)
The key fob’s auxiliary button can be used to trigger the Control Panel’s open
and the Control Panel will learn the fob’s serial number.
collector output.
• The default (0) disables this fob’s auxiliary button.
Select fob (#) equipment age (0-1)
• To use this fob’s auxiliary button, select the output function.
DEFAULT: New (0)
The Control Panel can be used with new or existing key fobs. FOB KEY 4 OUTPUT
• If this fob is new for the installation, leave the default of new (0). (0) disabled
• If this fob is already installed, select existing (1). (1) toggle output
(2) momentary output

27
Installer Programming
RF Keypad Programming
RF Keypad Programming Outline
The Control Panel can be programmed with up to four RF remote
control keypads or wireless touch screen keypads.
Programming RF keypads into the Control Panel involves selecting
the sensor number for a particular device, setting or learning the
keypad’s serial number, and selecting the other options for the
keypad.
• RF keypads #1 - #4 report as system sensors
#59 - #62 for emergency, and low battery reports.
RF KEYPAD REPORTING CODES
RF keypad #1 Reports as sensor #59
RF keypad #2 Reports as sensor #60 KEYPAD PROGRAMMING (Q-4) OUTLINE
RF keypad #3 Reports as sensor #61
STEP DOWN SELECT OPTION WITH
RF keypad #4 Reports as sensor #62 THROUGH OPTIONS THESE KEYS
• User Codes #1 - #8 are reported for openings and closings.
• User Code #0 is reported for Quick Arming.
ENTER ON CONTROL PANEL OR PRESS
Refer to Figure 56 for an outline of the steps required to program
SELECT RF KEYPAD #
RF remote control keypads into the Control Panel. The options that OR
can be set for each RF remote control keypad are:
TO SELECT FROM LIST
PRESS FOR NEXT OPTION OR PRESS SKIP TO JUMP TO Q-5
• RF Keypad Number — Keypad number 1-4
ENTER ON CONTROL PANEL OR PRESS
SELECT RF KEYPAD
• RF Keypad Used — Keypad used or not USED
OR
• RF Keypad Equipment Code — Sensor model TO SELECT FROM LIST
PRESS FOR NEXT OPTION
• RF Keypad Other Equipment Code — Enter special
ENTER ON CONTROL PANEL OR PRESS
Q-4 SUB-QUESTIONS

equipment code (only shown for sensors set as “other”) SELECT RF KEYPAD
EQUIPMENT CODE
OR
• RF Keypad Serial # — Serial number labeled on
keypad; hand enter or “learn” by sending signal PRESS FOR NEXT OPTION
TO SELECT FROM LIST

• RF Keypad Equipment Age — New unit or existing keypad ENTER RF KEYPAD

OTHER EQUIPMENT CODE
• RF Keypad Emergency Keys — Enable (ONLY FOR "OTHER" EQUIPMENT) ENTER ON CONTROL PANEL
or disable keypad emergency keys
PRESS FOR NEXT OPTION
• RF Keypad Voice Descriptor — Name
assigned to the keypad ENTER RF KEYPAD ENTER ON CONTROL PANEL OR PRESS

RF Keypad Summary Screen SERIAL NUMBER

shift THEN learn OR learn
After setting all the options for a sensor, the RF keypad summary
screen is displayed. The screen can also be displayed for AND SEND SIGNAL FROM SENSOR
PRESS FOR NEXT OPTION
programmed RF keypads during RF keypad program editing by
pressing the SUM button. ENTER ON CONTROL PANEL OR PRESS
SELECT RF KEYPAD
• The ← and → arrow buttons step through the RF keypad numbers. EQUIPMENT AGE
OR
• The EDIT CURRENT and EDIT NEXT buttons return to RF keypad TO SELECT FROM LIST
PRESS FOR NEXT OPTION
programming.
• Pressing SKIP goes to question Q-5 (Control Panel programming). SELECT RF KEYPAD ENTER ON CONTROL PANEL OR PRESS
EMERGENCY KEYS
(ONLY FOR NON-TS1 KEYPADS) OR

PRESS FOR NEXT OPTION

TO SELECT FROM LIST

PRESS insert FOR EACH WORD

CONSTRUCT RF KEYPAD
VOICE DESCRIPTOR ENTER ON CONTROL PANEL OR PRESS
OR
TO SELECT FROM LIST
edit
PRESS TO FINISH FOR THIS SENSOR, THEN next FOR NEXT SENSOR, OR skip FOR Q5

Figure 55. RF Keypad Summary Screen Figure 56. RF Keypad Programming Outline
28
Installer Programming
RF Keypad Programming Steps Enter RF keypad (#) serial number (7 digits)
DEFAULT: 0000000
Q-4 Select RF keypad # (1-4) or
Up to four wireless keypads can be used with each Control Panel. The options for
each sensor are programmed with sub-option questions.
RF keypad (#) keypad id (read-only)
RF keypad serial numbers for standard keypads can be manually entered or
• Begin by entering the RF keypad number or learned from the RF keypad. Model 2GIG-TS1 wireless touch screen keypads
select it using the ← or → arrows. serial numbers can only be learned from the keypad.
• Program the RF keypads by using the ↑ and ↓ Standard Keypads:
arrows to select the sub-options.
• For manual entry, enter the RF keypad number that
✓ NOTE: To skip RF keypad programming, press SKIP to jump from
was logged for the RF keypad being programmed. Use
question Q-4 to question Q-5 (Exit Delay programming).
the SHIFT button to access alpha characters.
• For automatic entry, press SHIFT then press LEARN.
Select RF keypad (#) used (0-1) The Control Panel will wait for an RF keypad transmission.
DEFAULT: Unused (0) Trigger the RF keypad being programmed, and the Control
RF keypads can be used with the Control Panel or not. Panel will learn the RF keypad’s serial number.
• The default (0) sets all RF keypads as unused.
• To enable programming for this RF keypad, select used (1). TS1 Wireless Touch Screen Keypads:
• For 2GIG-TS1 Wireless Touch Screen Keypads press LEARN. The Control
Select RF keypad (#) equipment code (0-9999) Panel will display “Pair with TS-1. Initiating learning process.” Press the
TS1 keypad’s PAIR WITH PANEL button. Both the TS1 and the Control
DEFAULT: (0000) other Panel will display “The learn operation succeeded” when complete.
The RF keypad equipment code defines the sensor’s manufacturer and type.
• The Control Panel will display “RF keypad (#1-4)” for keypad identification.
• The default is (0000) other. • The TS1 will display “Network ID: xxxx” which is the unique
• Select (867) PAD1-345 wireless keypad for a 2GIG-PAD1 RF keypad. serial number identifying the specific keypad.
• Select (1059) TS-1 wireless touchscreen keypad for • Press OK on both the Control Panel and TS1 to continue.
a 2GIG-TS1 Wireless Touch Screen Keypad. ✓ NOTE: The Model 2GIG-TS1 wireless touch screen keypad will
✓ NOTE: The TS-1 wireless keypad is not for UL985 installations. display “The security system is temporarily not operational” after
learning the keypad. This is normal, and will be displayed anytime the
Control Panel is in system configuration (programming) mode.
Enter RF keypad (#) other equipment code (0-9999)
DEFAULT: 0
Select RF keypad (#) equipment age (0-1)
✓ NOTE: This question is only displayed if “(0000) other” is
selected for an RF keypad’s equipment code. DEFAULT: New (0)
The equipment code is a 4-digit code that is assigned to the model of keypad The Control Panel can be used with new or existing RF keypads.
being used. • If this RF keypad is new for the installation, leave the default of new (0).
• Enter the equipment code number for the RF keypad. • If this RF keypad is already installed, select existing (1).

Select RF keypad (#) emergency keys (0-1)

DEFAULT: Enabled (1)
✓ NOTE: This step is not displayed for Model 2GIG-TS1 keypads.
Standard RF keypads have 24-hour emergency buttons labeled FIRE and
POLICE.
• The default (1) enables this RF keypad’s emergency keys.
• To disable this RF keypad’s emergency keys, select disabled (0),
the keys will not be able to trigger an alarm or report.
✓ NOTE: The RF keypad’s POLICE button will trigger a silent alarm
if programming question Q-16 is set to silent panic.
TO ENSURE SENDING A SIGNAL, BE SURE TO INSTRUCT THE END USER
TO PRESS THE RF KEYPAD EMERGENCY KEYS UNTIL THE KEYPAD’S
INDICATOR LIGHTS.

Construct RF keypad (#) voice descriptor

DEFAULT: Keypad (#)
The voice descriptor is the words the Control Panel will announce for this RF
keypad. Up to five words are allowed.
• Press INSERT to place a word from the vocabulary into the data entry field.
• Use the ← or → arrows to scroll through the words,
or enter the word’s 3-digit index number.
• Press INSERT again for the next word. Up to five words are allowed.
• To remove a word, press DELETE.

29
Installer Programming
Control Panel Programming Questions
Q-11 Enter CS #1 phone number (0-25 digits)
Q-5 Enter exit delay, in seconds (45-120) DEFAULT: No default
The telephone number for Central Station #1 can be up to 25 digits.
DEFAULT: 60 seconds (Required SIA CP01 Default)
The Exit Delay can be set from 45 to 120 seconds. • Enter the Central Station #1 telephone number.
• The SHIFT button accesses the pound and star symbols.
• The default (60) sets the Exit Delay to 60 seconds.
The P button adds a 3-second pause to the dialing.
• To change the Exit Delay, enter a value from (45-120) seconds.
✓ NOTE: If a second Central Station telephone number is programmed
✓ NOTE: This default can be changed without affecting SIA CP01 compliance. with question Q-41, the Control Panel will alternate between the
two Central Station telephone numbers. After two failed telephone
dialing attempts, the Control Panel will try to connect using the
Q-6 Enter entry delay 1, in seconds (30-240) GSM radio module if it is installed. If the GSM radio module is not
DEFAULT: 30 seconds (Required SIA CP01 Default) installed, the Control Panel will make eight dialing attempts.
The Entry Delay #1 can be set from 30 to 240 seconds.
• The default (30) sets the Entry Delay #1 to 30 seconds. Q-12 Enter CS #1 account number (4 digits)
• To change the Entry Delay #1, enter a value from (30-240) seconds. DEFAULT: No default
✓ NOTE: Per SIA CP01, the combination of the Abort Window Dialer Delay The account number for Central Station #1 is always four digits and can include
(Q-35) and the Entry Delay (Q-6 or Q-7) cannot exceed one minute. some alpha characters.
• Enter four digits for the Central Station #1 account number.
Q-7 Enter entry delay 2, in seconds (30-240) • The SHIFT button accesses B, C, D, E, and F characters.
DEFAULT: 45 seconds (Required SIA CP01 Default)
The Entry Delay #2 can be set from 30 to 240 seconds. Q-13 Select 2-way voice (0-2)
• The default (45) sets the Entry Delay #2 to 45 seconds. DEFAULT: Stay on line (1)
• To change the Entry Delay #2, enter a value from (30-240) seconds. The Control Panel supports 2-way voice communications between the subscriber
✓ NOTE: Per SIA CP01, the combination of the Abort Window Dialer Delay and the Central Station operator over the telephone line or the GSM cellular radio
(Q-35) and the Entry Delay (Q-6 or Q-7) cannot exceed one minute. (if installed) after an alarm has been reported.
• The default (1) allows 2-way audio over the telephone line or GSM radio.
Q-8 Select dialer (0-1) • Selecting (2) allows 2-way audio over the telephone
line or GSM radio during fire and CO alarms.
DEFAULT: Disabled (0)
The dialer (digital communicator) can be enabled for a monitored system or • To turn off the 2-way audio feature, select disabled (0).
disabled for a local alarm or when the GSM module is used exclusively for When the Control Panel connects with the operator, it will beep once per second
reporting. (every six seconds with a GSM connection). The beep alternates between two tones
and indicates the panel is waiting for a session command. If the operator fails to issue
• The default (0) sets the dialer as disabled. a command within one minute (three minutes with a GSM connection), the call is
• To turn on the dialer, select enabled (1). terminated. Once the operator presses a command option, the beeps will stop and
✓ NOTE: If the dialer is disabled with this programming question, a 5-minute audio session will start (3-minute audio session with a GSM connection).
telephone line failure detection is also disabled regardless of
the setting of the telephone fail detection question Q-63. When 2-way voice communications have been established, the Central Station
operator can use the following telephone keys to control the communications.
Each time the operator uses a command key, the session is extended for five
Q-9 Enter dialing prefix (0-4 digits) additional minutes (three minutes with a GSM connection). During the last minute
DEFAULT: No default of communications, the system will beep twice every 15 seconds to indicate that
Some telephone PBX systems require a dialing prefix to acquire a dial tone. time is running out.
• If the telephone system that the Control Panel is connected • Pressing enables Talk Mode one-way communication from
to requires a dialing prefix, enter up to four digits. the CS to the Premises and allows the operator to talk.
• The SHIFT button accesses the pound and star symbols. • Pressing enables VOX Mode two-way
The P button adds a 3-second pause to the dialing. communications from the CS to the premises.
• Pressing enables Listen Mode one-way
Q-10 Enter call waiting disable code (0-6 digits)
communication from the premises to the CS.
• Pressing extends the session five minutes
DEFAULT: No default (Required SIA CP01 Default) without changing the mode of operation.
If the subscriber’s telephone line has call waiting, incoming call tones on the line
could interfere with a communicator report to the Central Station. To prevent this, • Pressing causes the audio session to end and terminates the call.
the communicator can send the call waiting disable code before making a report.
• If call waiting is active on the telephone line, Q-14 Select silent panic/burglary listen only
enter the call waiting disable code. DEFAULT: Enabled (1)
• The SHIFT button accesses the pound and star symbols. The Control Panel supports audio listen-in of the subscriber premises from the
The P button adds a 3-second pause to the dialing. Central Station over the telephone line after a silent panic (police emergency),
✓ NOTE: If the first attempt fails, this code will be silent burglary, or duress alarm has been reported.
ignored on the rest of the attempts. • The default (1) enables audio listen-in after a silent
panic, silent burglary, or duress alarm.
• This option is permanently set and cannot be disabled.

30
Installer Programming

Q-15 Select dialing type (0-1) Q-21 Select siren supervision time (0-3)
DEFAULT: Touch tone (0) DEFAULT: Disabled (0)
The digital communicator can dial using tones or pulse. The wiring connection to the external sounder can be supervised. If the wiring to
• The default (0) is for touch tone (DTMF) dialing. the sounder is cut for 15, 30, or 45 seconds, a bell trouble report can be sent to
the Central Station.
• For rotary dialing, select pulse (1).
• The default (0) disables external sounder supervision.
• To supervise the external sounder wiring, select (1) for
Q-16 Select police emergency key (0-2) 15 seconds; (2) for 30 seconds; or (3) for 45 seconds.
DEFAULT: Audible (1)
The Control Panel’s panic emergency button action can be programmed. The panic
emergency button is displayed by pressing the Control Panel’s button. Q-22 Enter CS lack of usage notification time (0-255)
• The default (1) allows the panic emergency DEFAULT: Seven days (7)
button to sound an audible alarm. Inactivity reports can be sent to the Central Station if the system has not been
armed for a period of days.
• For silent activation, select silent panic (2).
• To disable and not display the panic emergency button, select disabled (0). • The default (7) sets the lack of usage feature at seven days.
✓ NOTE: Setting this programming question for silent panic (2) • To change the lack of usage feature duration, select (1-255) days.
will make the POLICE button on all RF keypads silent also. • To turn off the lack of usage feature, select disabled (0).

Q-17 Select fire emergency key (0-1) Q-23 Enter radio modem network failure time (0-255)
DEFAULT: Audible (1) DEFAULT: 30 minutes
The Control Panel’s fire emergency button can be enabled or disabled. The fire ✓ NOTE: GSM Module must be installed to use this function.
emergency button is displayed by pressing the Control Panel’s button. Sets the amount of time required for triggering a trouble condition if the system
• The default (1) allows the fire emergency button to sound an audible alarm. detects that the optional GSM radio modem has lost its cellular connection. (After
• To disable and not display the fire emergency button, select disabled (0). cellular service has been restored for five minutes, the trouble condition will clear.)
• The default (30) sets the failure detection time at 30 minutes.

Q-18 Select emergency key (0-1)

• To disable radio modem failure detection, select disabled (0).
• To choose a different failure detection time, select (1-255) minutes.
DEFAULT: Audible (1)
The Control Panel’s emergency button can be enabled or disabled. The panel’s
emergency button is displayed by pressing the Control Panel’s button. Q-24 Select radio modem network failure causes trouble (0-1)
• The default (1) allows the emergency button to sound an audible alarm. DEFAULT: Enabled (1)
• To disable and not display emergency button, select disabled (0). ✓ NOTE: GSM Module must be installed to use this function.
✓ NOTE: If all three emergency buttons are disabled, pressing the Control Panel’s Selects whether the control panel will sound and display trouble if the optional
button will display a message that the emergency buttons are disabled. GSM radio modem has lost its cellular connection. The trouble sounder can be
silenced by the user at the Control Panel (GSM trouble is logged regardless of
this setting). When the GSM radio modem connection is restored, the trouble
Q-19 Select quick arming (0-1) indications will automatically clear.
DEFAULT: Enabled (1) • The default (1) allows radio modem failure trouble indications.
Quick arming allows the subscriber to arm the system without having to enter • To turn off radio modem failure trouble indications, select disabled (0).
their User Code. (Quick arming reports as User 0 if open/close reports are sent.)
• The default (1) allows quick arming.
• To turn off quick arming, select disabled (0).
Q-25 Select radio modem network failure reports (0-1)
DEFAULT: Enabled (1)
✓ NOTE: GSM Module must be installed to use this function.
Q-20 Select swinger shutdown count (1-2) If the optional GSM radio modem loses its cellular connection, the Control Panel
DEFAULT: One trip (1) (Required SIA CP01 Default) can report the fault and restore via land-line if telephone reporting is enabled.
An unwanted series of multiple faults (usually caused by a bad contact or sensor) • The default (1) allows radio modem failure/restore reporting.
is called a “swinger”. Swinger shutdown sets the maximum number of alarms that
• To turn off radio modem failure/restore reporting, select disabled (0).
any sensor or hardwire loop can trigger during a single arming period.
✓ NOTE: CO and smoke detector alarms are not limited
by the swinger shutdown count. Other types of 24-hour Q-26 Select auto stay (0-1)
zones are limited by the swinger shutdown count. DEFAULT: Enabled (1) (Required SIA CP01 Default)
• The default (1) sets the swinger shutdown count at one trip. When auto stay is enabled and the system is armed in the Away Mode, if an exit/
• To set the swinger shutdown count to two trips, select (2). entry sensor is not violated during the Exit Delay, the system will arm in the Stay
✓ NOTE: This default can be changed without affecting SIA CP01 compliance. Mode.
• The default (1) enables the auto stay feature.
• To turn off the auto stay feature, select disabled (0).
✓ NOTE: The auto stay feature will not switch the system to Stay
Mode if the system is armed to Away Mode using a key fob
remote or remotely armed via telephone or computer.

31
Installer Programming

Q-27 Select exit delay restart (0-1) Q-33 Select cross sensor 47-48 (0-1)
DEFAULT: Enabled (1) (Required SIA CP01 Default) DEFAULT: Disabled (0)
When Exit Delay restart is enabled, re-entering the premises through an exit/ The Control Panel can be programmed so sensors 47 and 48 must both be
entry door during the Exit Delay will restart the Exit Delay. The restart of the Exit violated during a set time to trigger an alarm. This is called “cross sensor”
Delay will only occur one time; further violations of an exit/entry sensor will not verification. When enabled, if only one sensor (47 or 48) is violated, the alarm will
extend the Exit Delay. not trigger, but a trouble report will be sent for the sensor that triggered.
• The default (1) enables the Exit Delay restart feature. ✓ NOTE: CO and fire zone cannot be used for cross sensors.
• To turn off the Exit Delay restart feature, select disabled (0). • The default (0) disables the cross sensor feature.
• To use the cross sensor feature, select enabled (1).
Q-28 Select quick exit (0-1) ✓ NOTE: See Q-34 for information on setting the cross sensor timeout.

DEFAULT: Enabled (1)

The quick exit feature allows the user to start the Exit Delay while the system is Q-34 Enter cross sensor timeout, in seconds (10-120)
armed. When this feature is enabled, a QUICK EXIT button will appear on the DEFAULT: 10 seconds
Security Screen. Pressing QUICK EXIT while the system is armed allows the The cross sensor timeout is the maximum period of time allowed between
user to leave through an exit/entry door. After the Exit Delay expires, the system violation of sensors 47 and 48 that will trigger an alarm. If both sensors are
will return to being armed in the mode it was in before (either Stay or Away Mode). violated within this time period, an alarm will be triggered. If both sensors are not
• The default (1) enables the quick exit feature. violated within this time period, an alarm will not be triggered.
• To turn off the quick exit feature, select disabled (0). ✓ NOTE: Cross sensor verification must be enabled
with Q-33 for this feature to function.

Q-29 Enter periodic test, in days (0-255) • The default (10) sets the cross sensor timeout at 10 seconds.
• To change the cross sensor timeout duration, select (11-120) seconds.
DEFAULT: 30 days
Automatic test reports can be sent to the Central Station every certain number of days.
• The default (30) sends an automatic test report every 30 days. Q-35 Select abort window dialer delay (0-2)
• To set a different period for automatic test reports, select (1-255) days. DEFAULT: 30 seconds (1) (Required SIA CP01 Default)
• To disable automatic test reports, select (0). The Control Panel’s dialer (digital communicator) delays calling the Central
Station to allow the user enough time to cancel a false alarm before it is reported.

Q-31 Enter cancel time, in minutes (5-255)

• The default (1) sets the dialer delay at 30 seconds.
• To change the dialer delay, select (0) for 15 seconds or (2) for 45 seconds.
DEFAULT: 5 minutes (Required SIA CP01 Minimum) ✓ NOTE: Per SIA CP01, the combination of the Abort Window Dialer Delay
A cancel report will be sent to the Central Station after an alarm, if the system is (Q-35) and the Entry Delay (Q-6 or Q-7) cannot exceed one minute.
disarmed within the programmed time.
✓ NOTE: The dialer delay can be disabled per sensor without
• The default (5) sets the cancel time at five minutes. affecting SIA CP01 compliance. See sensor programming.
• For a longer cancel time, select (6-254) minutes.
• To have the Control Panel always send a cancel report when
the system is disarmed after an alarm, select (255). Q-36 Select burglary bell cutoff (0-4)
✓ NOTE: See Q-32 for information on displaying when a cancel report is sent. DEFAULT: 4 minutes (0)
When a burglary alarm is triggered, the bell will sound until the burglary bell cutoff
✓ NOTE: This default can be changed without affecting SIA CP01 compliance.
time expires.
Q-32 Select cancel display (0-1) • The default (0) sets the burglary bell cutoff time to 4 minutes.
DEFAULT: Enabled (1) (Required SIA CP01 Default) • To change the burglary bell cutoff time, select (1), (2), (3), or (4):
A cancel report will be sent to the Central Station after an alarm, if the system is BURGLARY BELL CUTOFF TIME
disarmed within the programmed time. The Control Panel can also show on the
(0) 4 minutes
display that a cancel report was sent.
(1) 8 minutes
• The default (1) enables the cancel display feature.
• To turn off the cancel display feature, select disabled (0). (2) 12 minutes
✓ NOTE: See Q-31 for information on setting the cancel report trigger time. (3) 16 minutes
✓ NOTE: This default can be changed without affecting SIA CP01 compliance. (4) Unlimited time
✓ NOTE: The 24-hour Auxiliary Alarm Zone (08) does not follow the burglary bell
cutoff time and will sound the Control Panel’s local alarm until a user code is
entered. The Auxiliary Alarm Zone does not trigger the external siren (if used).

32
Installer Programming

Q-37 Select fire bell cutoff (0-4) Q-42 Select remote control phone (0-3)
DEFAULT: 4 minutes (0) DEFAULT: Data and voice (3)
When a fire alarm is triggered, the bell will sound until the fire bell cutoff time This setting controls remote telephone access to the system.
expires. The data option is for the installer. It allows access for programming and operating
• The default (0) sets the fire bell cutoff time to 4 minutes. the system with custom PC downloader software.
• To change the fire bell cutoff time, select (1), (2), (3), or (4): The voice option is for the subscriber. It allows the subscriber to call the system
FIRE BELL CUTOFF TIME from an off-site phone, to get the status of the system, and to perform remote
commands. These commands are executed by entering touch tones. The status
(0) 4 minutes is reported back via voice prompts. A valid User Code is required for remote
(1) 8 minutes telephone access. The user will be able to perform the following functions: arm
(2) 12 minutes in any mode, disarm, bypass, get system status, and turn on or turn off the open
collector output.
(3) 16 minutes
If voice access is enabled, to connect to the panel, the subscriber will need to call
(4) Unlimited time the telephone number that the Control Panel is connected to, wait for one or two
rings, then hang up. The subscriber needs to call again, within 10-45 seconds,
and the Control Panel will answer the call.
Q-38 Enter time to detect AC loss, in minutes (0-30)
When the panel answers the phone, the user will be prompted to enter their code.
DEFAULT: 10 minutes (10) If a valid code is entered, the system will announce the current system status. If
AC power loss will cause an AC power loss alert to be displayed, and the
an invalid code is entered, the panel will ask for the code again. After two invalid
length of time before it’s displayed can be set. When power returns, the time
attempts, the panel will disconnect. After two calls, with two invalid attempts each,
required before the AC power loss alert automatically clears is fixed at
the panel will lock out. The lock out will last for 30 minutes.
one minute.
• The default (3) enables data and voice access.
• The default (10) sets the AC power loss alert display time to ten minutes.
• To change the AC power loss alert display time, enter (0-30) minutes. • For data only (PC downloader) access, select (1).
✓ NOTE: After the AC power alert is displayed or clears, the • For voice access only, select (2).
AC power loss report or AC power restore report can be sent to the • To disable remote access, select (0).
Central Station immediately, or at a random time, see Q-39.
REMOTE CONTROL PHONE MODE
✓ NOTE: The Control Panel’s AC power icon displays the power status
immediately. A red “X” over the icon indicates no AC power. (0) disabled (no remote control phone)
(1) data only
Q-39 Select random AC loss report time (0-1) (2) voice only
DEFAULT: Enabled (1) (3) data and voice
This feature allows the system to report AC power loss and AC power restore at
a random time of up to 45 minutes after the event occurs. This helps to reduce TELEPHONE KEY REMOTE CONTROL COMMAND
Central Station congestion due to a wide-spread power outage affecting many
Control Panels at once. The random AC power status report timer is triggered 1 System status report
based on the time set by Q-38. 2 Arm the system in Away Mode
• The default (1) allows random timed AC power reports. 3 Arm the system in Stay Mode
• To turn off random timed AC power reports, select disabled (0). 4 Disarm the system
5 Turn on the auxiliary output
Q-40 Enter CS #2 phone number (0-25 digits) 6 Turn off the auxiliary output
DEFAULT: No default 7 Stop the system status report
The telephone number for Central Station #2 can be up to 25 digits. Central
8 Disconnect (hang up)
Station telephone #2 is dialed as backup in case telephone #1 does not connect.
9 Repeat command menu
• Enter the Central Station #2 telephone number.
• The SHIFT button accesses the pound and star symbols. # Bypass all open sensors and arm system
The P button adds a 3-second pause to the dialing. ✓ NOTE: Remotely arming the system to Away Mode will not start
an Exit Delay or activate Auto Stay Mode (if enabled).
Q-41 Enter CS #2 account number (4 digits)
DEFAULT: No default Q-43 Enter installer code (4 digits)
The account number for Central Station #2 is always four digits and can include DEFAULT: 1561
some alpha characters. The Installer Code is the code required to enter the Installer Toolbox.
• Enter four digits for the Central Station #2 account number. • The default for the Installer Code is 1561.
• The SHIFT button accesses B, C, D, E, and F characters. • To change the Installer Code, enter a new 4-digit code.
BE SURE TO WRITE DOWN THE NEW CODE !!!
✓ NOTE: The Installer Code must be unique from any User Codes.

33
Installer Programming

Q-44 Select lock installer programming (0-2) Q-47 Select trouble resound after holdoff (0-7)
DEFAULT: Disabled (0) DEFAULT: Disabled (0)
The installer programming lockout feature is provided to prevent takeovers. The Fire and CO sensors are required to re-sound trouble beeps every four hours
Control Panel can be set to limit an installer’s access to programming questions until the trouble is resolved, even if the trouble is acknowledged at the Control
after a period of 48 hours. The 48 hour lockout timer starts when the installer exits Panel. The Control Panel can be set to delay re-sounding these types of trouble
system configuration mode. beeps for 1-7 days.
Three options are available: unlimited full access to programming (no lockout), ✓ NOTE: This feature is not allowed in UL 985 installations. The
limited access to programming after 48 hours, or no access to programming after setting must be disabled (0) in this grade of installation.
48 hours. • The default (0) allows trouble beeps for CO and fire sensors
• The default (0) selects unlimited full access to programming (no lockout). to re-sound every four hours after being acknowledged.
• To deny access to programming after 48 hours, • To delay re-sounding trouble beeps for CO
select no access to programming (1). and fire sensors, select (1-7) days.
• To select limited access to programming after 48 hours, select (2). After the
system has run for 48 hours, installer will be able to view, but not change,
the Central Station phone number, Central Station account number,
Q-48 Enter download csid (6 digits)
DEFAULT: 000000
lock installer programming, download ID, and default lockout fields.
The system supports a 6-digit CSID code that is used for remote telephone
After the 48 hour lockout timer has locked out the system, the timer can be reset programming of the Control Panel. This code is verified when the Control Panel
through the GSM radio or PC downloader by remotely setting this question Q-44 connects with the downloading software. If the CSID code doesn’t match the
to (0) or (2). Setting the option to (0) or (2) will restart the 48 hour lockout timer. downloading software, the Control Panel will deny the connection.
• The CSID code can be entered manually with this programming question.
Q-45 Select lock default programming (0-2) • If this field is left with the default (000000), the first time
DEFAULT: Default all (0) the downloading software connects with the Control Panel,
The Control Panel may be able to be hard reset (or soft reset from the Installer the field will be filled with the software’s CSID.
Toolbox) to its factory default values depending on the value entered for this
programming question. Q-49 Select programming mode entry reports to CS (0-1)
The Control Panel is hard reset by pressing and holding the and DEFAULT: Disabled (0)
buttons while applying power to the Control Panel. A report can be sent to the Central Station any time installer programming mode
The default lockout feature is provided to prevent takeovers. Three options are is entered and exited.
available: allow default of all options, allow default of some but not all options, not • The default (0) prevents reporting programming mode entry and exit.
allow default of any options. • To report programming mode entry and exit, select enabled (1).
• The default setting of default all (0) allows resetting the Control Panel to all ✓ NOTE: This report can only be sent through the telephone
its factory defaults. dialer. It is not supported through the GSM radio.
• To allow resetting the Control Panel to all its factory defaults except the
Central Station phone number, Central Station account number, lock installer
programming, download ID, and default lockout fields, select (1).
Q-50 Select trouble reports to CS (0-1)
DEFAULT: Enabled (1)
• To deny hard and soft resetting of the Control Panel, select default none (2). Trouble reports can be sent to the Central Station when any sensor trouble
If option (1) or (2) is selected, the option will take effect after the system has run condition occurs.
for 48 hours. This allows the installer to go back and make changes if required. • The default (1) allows reporting sensor trouble conditions.
• To not report sensor trouble conditions, select disabled (0).
Q-46 Select trouble doesn’t sound at night (0-1) ✓ NOTE: This setting does not affect trouble reports caused by Control
Panel conditions, only trouble reports caused by sensors.
DEFAULT: Enabled (1)
The Control Panel will sound trouble beeps caused by AC loss, system low
battery, sensor low battery or RF supervision, failure to communicate, Control Q-51 Select manual bypass reports to CS (0-1)
Panel tamper while disarmed, and GSM radio faults. DEFAULT: Disabled (0)
To prevent annoying the subscriber, the system can be set to suppress trouble Manual bypass reports can be sent to the Central Station when any sensor has
beeps from sounding from 10 pm to 9 am. The trouble(s) will still be displayed and been manually bypassed by the user.
immediately reported to the Central Station, and can be acknowledged, but they • The default (0) prevents sending manual bypass reports.
won’t sound beeps until after 9 am. • To allow sending manual bypass reports, select enabled (1).
If the trouble condition(s) self-clear or are acknowledged before 9 am, no trouble
beeps will sound after 9 am (the conditions will still be recorded in the event
log).
• The default (1) suppresses trouble beeps from 10 pm to 9 am.
• To allow trouble beeps at any time, select disabled (0).
✓ NOTE: For UL985 Installations, this feature must be disabled.

34
Installer Programming

Q-52 Select AC loss reports to CS (0-1) Q-58 Select trouble restore reports to CS (0-1)
DEFAULT: Enabled (1) DEFAULT: Enabled (1)
AC power loss reports can be sent to the Central Station if the Control Panel Trouble restore reports can be sent to the Central Station when any sensor
loses AC power. trouble condition clears.
• The default (1) allows AC power loss reports. • The default (1) allows trouble restore reports.
• To turn off AC power loss reports, select disabled (0). • To turn off trouble restore reports, select disabled (0).
✓ NOTE: The AC power will have to be absent from the Control Panel for the
time set by programming question Q-38 before the AC power loss trouble
alert is displayed (the default is 10 minutes). If programming question Q-59 Select bypass restores reports to CS (0-1)
Q-39 is enabled, the actual AC power loss report will occur at a random time DEFAULT: Disabled (0)
of up to four hours after the AC power loss trouble alert is displayed. Bypass restore reports can be sent to the Central Station when any sensor that
✓ NOTE: The Control Panel’s AC power icon displays the power status was force bypassed or manually bypassed gets restored.
immediately. A red “X” over the icon indicates no AC power.
• The default (0) prevents bypass restore reports.
• To allow bypass restore reports, select enabled (1).
Q-53 Select system low battery reports to CS (0-1)
DEFAULT: Enabled (1)
Low battery reports can be sent to the Central Station if the Control Panel’s
Q-60 Select AC restore reports to CS (0-1)
battery tests low. DEFAULT: Enabled (1)
AC power restore reports can be sent to the Central Station when the Control
• The default (1) allows Control Panel low battery reports. Panel regains AC power after an AC power loss.
• To turn off Control Panel low battery reports, select disabled (0).
• The default (1) allows AC power restore reports.
• To turn off AC power restore reports, select disabled (0).
Q-54 Select RF low battery reports to CS (0-1) ✓ NOTE: The AC power will have to be restored to the Control
DEFAULT: Enabled (1) Panel for one minute before the AC power loss trouble alert
Sensor low battery reports can be sent to the Central Station if a sensor battery automatically clears. If programming question Q-39 is enabled, the
actual AC power restore report will occur at a random time of up to
tests low and sends a low battery transmission to the Control Panel.
four hours after the AC power loss trouble alert has cleared.
• The default (1) allows sensor low battery reports. ✓ NOTE: The Control Panel’s AC power icon displays the power status
• To turn off sensor low battery reports, select disabled (0). immediately. A red “X” over the icon indicates no AC power.

Q-55 Select opening reports to CS (0-1) Q-61 Select system low battery restore reports to CS (0-1)
DEFAULT: Disabled (0) DEFAULT: Enabled (1)
Opening reports can be sent to the Central Station each time the system is Control Panel low battery restore reports can be sent to the Central Station if the
disarmed. The user or key fob number is indicated in the opening report. Control Panel battery had tested low and is now OK.
• The default (0) prevents opening reports. • The default (1) allows Control Panel low battery restore reports.
• To allow opening reports, select enabled (1). • To turn off Control Panel low battery restore reports, select disabled (0).

Q-56 Select closing reports to CS (0-1) Q-62 Select RF low battery restores reports to CS (0-1)
DEFAULT: Disabled (0) DEFAULT: Enabled (1)
Closing reports can be sent to the Central Station each time the system is armed. Sensor low battery restore reports can be sent to the Central Station if a sensor
The user or key fob number is indicated in the closing report. If Quick Arming is battery had tested low and is now OK.
enabled, User #0 is indicated for the closing report. • The default (1) allows sensor low battery restore reports.
• The default (0) prevents closing reports. • To turn off sensor low battery restore reports, select disabled (0).
• To allow closing reports, select enabled (1).

Q-63 Select phone fail detect (0-1)

Q-57 Select alarm restore reports to CS (0-1) DEFAULT: Disabled (0)
DEFAULT: Disabled (0) The system can monitor the telephone line connected to the Control Panel. If
Alarm restore reports can be sent to the Central Station after an alarm when the telephone line is shorted or cut, the Control Panel will indicate telephone line
either the bell timeout has been reached or the system is disarmed. trouble by sounding trouble beeps and displaying the no-phone icon.
If alarm restores are enabled and swinger shutdown is set to two, a restore will If the optional GSM radio modem is installed, the telephone line failure will still be
be reported if the sensor is closed (normal state) at bell cutoff or becomes closed reported if this question is enabled.
after bell cutoff. If swinger shutdown is set to one, a restore will only be sent if • The default (0) disables this feature.
the sensor is closed at the time of disarm. Restores are not sent if a sensor is in
• To turn on this feature, select enabled (1).
swinger shutdown until the time of disarm and the sensor is closed.
✓ NOTE: If the dialer is disabled with programming question Q-8,
• The default (0) prevents alarm restore reports. telephone line failure detection is also disabled regardless
• To allow alarm restore reports, select enabled (1). of the setting of this programming question.

35
Installer Programming

Q-64 Select smart test reports Q-71 Select system tamper causes trouble (0-1)
DEFAULT: Disabled (0) DEFAULT: Enabled (1)
Smart test reports are a way to reduce Central Station traffic. If smart test reports The Control Panel’s case has a tamper switch that detects if the case has been
are enabled and regular periodic test reports are enabled, any non-test report to opened. The system can be programmed so that a tamper switch activation will
the Central Station (alarm, restore, trouble, etc.) during the normal operation of cause a trouble indication if the system is disarmed, and an alarm if the system
the system will reset the periodic test report timer. Periodic test reports would only is armed.
be sent if the Control Panel has not reported in any way to the Central Station. • The default (1) allows the Control Panel tamper switch to trigger trouble
• The default (0) prevents smart test reports. when the system is disarmed, and alarm when the system is armed.
• To allow smart test reports, select enabled (1). • To have the system ignore the Control Panel
tamper switch, select disabled (0).
✓ NOTE: The GSM radio does not report tamper when the system is disarmed.
Q-65 Select RF jam causes trouble (0-1)
DEFAULT: Disabled (0)
The system can monitor the Control Panel’s sensor receiver and detect whether a Q-72 Select quick bypass (0-1)
transmitter is stuck on the air causing jamming. When jam detect is enabled, the DEFAULT: Disabled (0)
Control Panel will indicate a trouble condition if RF jamming is detected. Normally, sensors that are violated (open) at the time the system is armed will
✓ NOTE: This programming question only functions if trouble require the user to enter their code to force bypass them. The Control Panel can
reports are enabled with programming question Q-50. be programmed so that when the system is armed with open sensors, a code is
• The default (0) disables RF jam detection. not required to bypass the open sensor(s) and complete the arming.
• To turn on RF jam detection, select enabled (1). • The default (0) requires entering a code to bypass sensors.
• To allow bypassing sensors without a code, select enabled (1).
Q-66 Select daylight saving (0-1)
DEFAULT: Enabled (1) Q-73 Select disarming keyfob after alarm (alert) (0-1)
The Control Panel can adjust its displayed clock and internal clock for daylight DEFAULT: Disabled (0)
saving time. If the GSM radio is used, the time will be automatically adjusted The system can produce a unique sound when it’s disarmed with a key fob after
regardless of this setting. The system default is set for post 2007 daylight an alarm has occurred. Four beeps will sound from the Control Panel’s speaker,
saving changeover dates. These dates can be modified in case the daylight four chirps will sound from the external sounder (if installed). This feature serves
saving changeover date moves again. as a safety alert to the user so they can enter the protected premises with caution.
• The default (1) enables daylight saving time adjustment. • The default (0) will not cause a unique sound
• To turn off automatic daylight savings adjust, select disabled (0). when disarming after an alarm.
✓ NOTE: If required, use programming questions Q-67, Q-68, Q-69, • To cause unique sound when disarming after an alarm, select enabled (1).
and Q-70 to modify the daylight saving start and stop dates.

Q-74 Select keyfob arm / disarm confirmation (0-1)

Q-67 Select daylight saving start month (01-12) DEFAULT: Disabled (0)
DEFAULT: March (03) The system can produce a unique sound when it’s armed or disarmed with a
• The default (03) sets March as the daylight saving start month. key fob. The Control Panel’s speaker will sound one beep when arming and two
• To change the start month, enter the month, January - December beeps when disarming. The external sounder (if installed) will sound one chirp
(01-12), that the new daylight saving time will start. when arming and two chirps when disarming (four beeps after an alarm if Q-73 is
enabled). This feature indicates to the user that their key fob signal was received
by the Control Panel in case other arm/disarm indications (armed LED, etc.) are
Q-68 Select daylight saving start Sunday (1-7) not available or visible to the user.
DEFAULT: 2nd Sunday (2) • The default (0) will not cause a unique sound when controlled by a key fob.
• The default (2) sets the second Sunday as the daylight saving start week.
• To cause a unique sound when controlled by a key fob, select enabled (1).
• To change the start week, enter the 1st, 2nd, 3rd, 4th, last, second
from last, third from last (1-7) as the daylight saving start week.
Q-75 Select auto unbypass for manual bypass (0-1)
Q-69 Select daylight saving end month (01-12) DEFAULT: Enabled (1)
Violated (open) sensors can be manually bypassed by the user through the User
DEFAULT: November (11) Toolbox or force bypassed at the time of arming.
• The default (11) sets November as the daylight saving end month.
☞ Force bypassed sensors automatically have their
• To change the end month, enter the month, January - December
bypasses removed when the system is disarmed.
(01-12), that the custom daylight saving time will end.
☞ Manually bypassed sensors can have their bypass automatically
removed at disarming or have their bypasses remain in place.
Q-70 Select daylight saving end Sunday (1-7) • The default (1) automatically removes bypasses from manually
DEFAULT: 1st Sunday (1) bypassed sensors when the system is disarmed.
• The default (1) sets the first Sunday as the daylight saving end week. • To have manually bypassed sensors remain bypassed
• To change the end week, enter the 1st, 2nd, 3rd, 4th, last, second when the system is disarmed, select disabled (0).
from last, third from last (1-7) as the daylight saving end week.

36
Installer Programming

Q-76 Select force bypass reports (0-1) Q-79 Select Z-Wave feature (0-3)
DEFAULT: Disabled (0) DEFAULT: Disabled but visible (1)
The system can report which sensors have been force bypassed by the user The Z-Wave home services feature can be enabled or disabled with various
when the system is armed. Forced bypassed sensors are always recorded in the remote control access options.
event log, regardless of the setting of this programming question. • The default (1) displays the SERVICES button, but will show a message
• The default (0) prevents reporting forced bypassed sensors. that the feature is currently disabled and the user should call the installer.
• To report forced bypassed sensors, select enabled (1). • To hide the SERVICES button, select disabled and hidden (0).
• To show the SERVICES button and disable off-
Q-77 Select event log (0-3)
site remote control, select (2).
• To show the SERVICES button, with Z-Wave rules disabled
DEFAULT: All events (3) and off-site remote control enabled, select (3).
To control the amount of event log entries, the events that get recorded into the
system’s event log can be selected by type. This setting filters the events that
populate the event log. Q-80 Select Z-Wave switches feature (0-1)
• The default (3) records all events in the event log. DEFAULT: Disabled (0)
• For different event log filtering options, select (0), (1), or (2): Display of the Home Service’s SWITCHES button can be enabled or disabled.

EVENT LOG FILTERS ✓ NOTE: This programming question only functions if the
Z-Wave feature enable question Q-79 is set to (2) or (3).
(0) disabled (no events logged) • The default (0) hides the SWITCHES button.
(1) all events except open, closing, and bypass • To display the SWITCHES button, select enabled (1).
(2) all events except open and closing
(3) all events Q-81 Select Z-Wave thermostats feature (0-1)
DEFAULT: Disabled (0)
Q-78 Select output (00-10)
Display of the Home Service’s THERMOSTATS button can be enabled or
disabled.
DEFAULT: Follows internal sounder alarm (11)
✓ NOTE: This programming question only functions if the
(Required SIA CP01 Default) Z-Wave feature enable question Q-79 is set to (2) or (3).
The system’s open collector output is available on the Control Panel’s terminal • The default (0) hides the THERMOSTATS button.
block to connect to an external device. The conditions that will cause the open
• To display the THERMOSTATS button, select enabled (1).
collector output to activate are programmable.
• Select one activation option for the Control Panel’s open collector output:
OPEN COLLECTOR OUTPUT MODE
Q-82 Select Z-Wave door locks feature (0-1)
DEFAULT: Disabled (0)
(00) disabled Display of the Home Service’s DOOR LOCKS button can be enabled or disabled.
(01) activated when armed ✓ NOTE: This programming question only functions if the
(02) activated when disarmed Z-Wave feature enable question Q-79 is set to (2) or (3).
• The default (0) hides the DOOR LOCKS button.
(03) activated on FTC (failure to communicate)
• To display the DOOR LOCKS button, select enabled (1).
(04) activated on siren supervision
(05) activated on radio fault
(06) activated on burglary alarm
Q-83 Select temperature display units (0-1)
DEFAULT: Degrees Fahrenheit (0)
(07) activated on fire alarm The Home Service’s Z-Wave thermostat display screens can show the
(08) activated on any alarm temperature in degrees Fahrenheit or degrees Celsius.
(09) activated on any system trouble ✓ NOTE: This programming question only functions if the
Z-Wave feature enable question Q-79 is set to (2) or (3)
(10) Z-wave activation (Option #10 not currently active)
and the thermostat feature is enabled with Q-81.
(11) follows internal sounder alarm • The default (0) displays temperature in degrees Fahrenheit.
(12) follows exit/entry beeps • To display temperature in degrees Celsius, select (1).

37
Installer Programming

Q-84 Select services require master code (0-1)

DEFAULT: Disabled (0)
The SERVICES button can be configured to require the use of the master code
to access Services.
• The default (0) disables the requirement for the Master
User Code to access the SERVICES menu.
• To require the use of the Master User Code to access
the SERVICES menu, select enabled (1).
When enabled then the Master User Code is required to access the Services and
the Z-wave device configurations. This keeps unauthorized users from being able
to change Z-wave settings, such as temperature, lights and locks.

Q-85 Select master user access to zwave toolbox (0-1)

DEFAULT: Disabled (0)
The Z-Wave Toolbox menu can be set to require the use of the Master User Code
or the Installer Code. By default, the Installer Code is required for users to access
the Z-Wave Toolbox.
• The default (0) requires the use of the Installer Code to access the Z-Wave
Toolbox menu and all of its features, including the Advanced Toolbox.
• To require the use of the Master User Code or the Installer Code
to access the Z-Wave Toolbox menu, select enabled (1).
✓ NOTE: When enabled (1) the Installer code will still be required
to access the Advanced Toolbox menu. This prevents end
users from adding or removing Z-Wave devices.

Q-86 Select disable siren after two-way audio (0-1)

DEFAULT: Disabled (0)
This setting enhances system operation in personal emergency applications and
also provides the dealer with the option of the siren sounding until the bell cut off
or to the end of a two-way-voice session.
• The default (0) will cause the siren to resume after two-way
audio (if the bell cut off timer has not expired).
• Enable (1) will cause the siren to shut off after a two-way audio session.

38
Final Installation Setup
Exiting Programming 6. Press BRIGHTNESS / VOLUME. Set the level for the display
After programming the Control Panel, all the changes need to brightness. Set the chime & voice volume. Press OK when finished.
be saved in memory. After saving, the programmed settings will
remain in memory, even after a total power loss.
1. After setting all the required programming values for
the sensors and the Control Panel, press END.
2. Review the Control Panel Summary screen. Use the ↓ and ↑ arrows
to scroll through the listing. Verify that each option is set correctly.
3. To save the programming changes, be sure the SAVE CHANGES
option is checked. To exit without saving programming changes
un-check the SAVE CHANGES option (for verification, an additional Figure 60. Brightness / Volume Screen
confirmation screen will display). Press EXIT. The Control Panel
will take a few seconds to restart and display the Home Screen. 7. Press → to view the second User Toolbox screen.

Figure 57. Programming Summary Screen Figure 61. User Toolbox Screen 2 of 3
Customizing the Installation 8. Press BACKLIGHT TIMEOUT and set the display lighting
After programming the Control Panel, go to the User Toolbox and timeout. Choose the length of time that the display will
customize the system to suit the installation. remain lit after it is idle. Press OK when finished.
1. After the Control Panel restarts, press SECURITY, MENU, TOOLBOX to
access the User Toolbox. Enter the Master User Code (default = 1111).

Figure 62. Backlight Timeout Screen

9. Press SET DATE and SET TIME to set the calendar and clock. On
Figure 58. User Toolbox Screen 1 of 3 the Set Date screen, use the ↓ and ↑ arrows to set the month, day,
and year. On the Set Time screen, use the ↓ and ↑ arrows to set the
2. Press USER MANAGEMENT.
hours, minutes, and AM/PM. Press OK when finished. A confirmation
3. Setup the User Codes. Press a User button to add, change, screen will show. Verify the time and date, then Press OK.
or delete a User Code. The system will ask to confirm the
✓ NOTE: If the GSM radio module is installed and registered, the
code entered. Be sure to set a Duress Code as User #8.
date and time will be set automatically.
✓ NOTE: User codes 0000 and 0001 are not permitted.
4. Setup each User Code with the User Access Option Screen. Each
User Code can be set to be currently valid or not, or to have conditional
validity depending on a time and date schedule. Refer to the User’s
Guide for details on setting User Code Access Schedules.
5. Press BACK when finished.

Figure 63. Set Date Screen

10. Press BACK to return to the Security Screen or press
the button to return to the Home Screen.
The installation and installer programming of the Control Panel is
now complete. Continue to the next section to test the system.

Figure 59. User Management Screen

39
Installer Testing
Testing the System
After the installation is complete and the Control Panel
programming is complete, the system must be tested to ensure
proper operation.
System testing is performed through the Installer Toolbox screen.
1. From the Home Screen, press the lower right corner of the screen.
2. Enter the Installer Code (default = 1561) to access the Installer Toolbox.

Sounder Disable/Enable Figure 64. Installer Toolbox

Since installer testing will cause the Control Panel’s internal and
external alarm sounder to activate, an option to lower the sounder
is available.
1. From the Installer Toolbox Screen, press DISABLE SOUNDER.
2. A confirmation screen will be displayed. Press OK. Four beeps
will sound from the internal sounder, and a short siren will sound
from the external sounder. The external siren will be disabled
and the internal sounder will be lowered for 30 minutes.
3. A second confirmation screen will be displayed to verify
that the test sounds were produced. Press OK.
4. While the sounder is disabled, the sounder disable
icon will be displayed on the status bar. Figure 65. Sounder Disable Screen
The sounder disable will automatically time out after 30 minutes,
and the sounder will automatically become active again.
To re-enable the sounder manually, follow these steps:
1. From the Installer Toolbox Screen, press ENABLE SOUNDER.
2. A confirmation screen will be displayed. Press OK.

Zone Reporting Test

To verify that the Central Station will correctly receive reports from
each zone type, perform the following tests:
1. Inform the Central Station that test signals will be sent.
2. Trigger a 24-hour fire sensor (if installed) or press the FIRE
emergency button (if enabled), wait about 45 seconds for Figure 66. Sounder Disable Confirmation Screen
the report to complete, then disarm the Console.
3. Trigger a 24-hour panic sensor (if installed) or press the
PANIC emergency button (if enabled), wait about 45 seconds
for the report to complete, then disarm the Console.
4. Trigger a 24-hour emergency sensor (if installed) or press the
EMERGENCY emergency button (if enabled), wait about 45 STATUS BAR
SHOWING SOUNDER
seconds for the report to complete, then disarm the Console. IS DISABLED
5. Arm the system then trigger a burglary sensor, wait for
the system to go into alarm, wait about 45 seconds for
the report to complete then disarm the Console.
6. Check with the Central Station that each zone type was reported,
then inform the Central Station that the testing is complete.
Figure 67. Sounder Disable Icon on Status Bar

40
Installer Testing
Walk Test Mode
Walk Test Mode is for testing all the sensors. It verifies that each
sensor is being received correctly by the Control Panel. The walk
test also tests the Control Panel’s indicators and sounder.
✓ NOTE: The Walk Test Mode will automatically end after 25
minutes.

Signal Strength Indicators

An important feature is the received signal strength indicators
displayed by the Control Panel for each of the sensors. Even though
the Control Panel’s RF receiver is high-sensitivity, reception quality
of sensors at the Control Panel can vary over time, depending on
the amount of background RF noise on the receiver’s operating
frequency. The signal strength indicators are an important aid to
the installer for determining the best location to mount the sensors
and Control Panel.
During the walk test, the Control Panel will display the signal strength
of the RF transmissions received from each of the sensors. This
will help identify any sensors that are received with a weak signal Figure 68. Installer Toolbox Screen
at the Control Panel. Sensors with low signal strength might need
to be re-mounted to a location that produces stronger reception
at the Control Panel. The higher the sensor signal strength, the
better.
During the test, the system will beep every 30 seconds to indicate
that the system is in Walk Test Mode. During the last 5 minutes of
the test, the system will beep two times every 30 seconds.
✓ NOTE: Entering the Walk Test Mode will send a “start test”
report to the Central Station. Exiting the Walk Test Mode will
send a “stop test” report to the Central Station.
To perform a walk test, follow these steps: Figure 69. Sensor Test Screen During Testing
1. From the Installer Toolbox screen, press WALK TEST.
2. The icon will display on the Control Panel’s status bar and a beep will
sound every 30 seconds to indicate that the system is in Walk Test Mode.
3. Each of the sensors and their status will be shown on the on the sensor
test screen. Use the ↓ and ↑ arrows to scroll through the sensor list.
4. Activate the first sensor listed and view the result on the display:
• When a sensor is received by the Control Panel, three beeps will sound
and the display will light a green bar to the left of the sensor’s name.
• The received signal strength of the sensor will display as one to five
Figure 70. Sensor Test Screen Completed and Passed
green bars. The more bars, the higher the signal strength.
• If the signal level is sufficient, a check mark will display for the sensor.
• For sensors with multiple loops, wait 15 seconds between
triggering each loop.
5. Continue testing with each of the other sensors listed.
6. After all the sensors have been tested, press the OK button
to test the Control Panel’s indicators and sounder.
7. Press each test item displayed, observe the Control Panel item
being tested, and answer the yes/no question for the test.
8. Press OK when all items have been tested. The Control
Figure 71. Indicator and Sounder Test Screen
Panel will display a summary of the test results.
9. Press OK to return to the Installer Toolbox.

41
Installer Testing
Radio Status Mode
✓ NOTE: GSM Module must be installed to use this function.
The GSM Radio Status screen displays data for the GSM radio (if
installed).The screen displays signal strength, serial number, registration
status, and other information about the GSM radio module status. The
information may be helpful for radio installation troubleshooting.
Follow these steps to check the radio status:
1. From the Installer Toolbox screen, press the RADIO STATUS button.
2. The system will display the GSM Radio Info screen. Each Figure 72. Installer Toolbox Screen
test item is displayed, followed with its current condition.
Scroll through the info screen with the ↓ and ↑ arrows.
• Text is displayed in red if the tested signal strength is zero
or too low, or the GSM module is not registered.
• Text is displayed in orange if the connection is
idle and the GSM module is registered.
• Text is displayed in green if the signal strength is
good and the GSM module is registered.
GSM Radio Test
A RUN RADIO TEST button is provided on the GSM Radio Status Figure 73. GSM Radio Info Screen
screen. Pressing this button will test the GSM cell phone connection
to the Central Station.
The same test can also be run using the CELL PHONE TEST button
on the User Toolbox screen #3.
Follow these steps to test the GSM radio:
1. From the Radio Status screen, press the RUN RADIO TEST button.
2. The system will display the Cell Phone Test screen. The top portion
of the screen shows the actions that the Control Panel is taking.
The bottom portion of the screen shows the results of the actions.
Scroll through the status screen with the ↓ and ↑ arrows. Figure 74. GSM Radio Test Screen
3. When the test is complete, press OK to return to the Installer Toolbox.

Telephone Test
The telephone test checks the land-line connection to the Central
Station through the Control Panel’s built-in digital communicator.
The test is accessed through the User Toolbox screen #3.
Follow these steps to test the digital communicator:
1. On toolbox screen #3, press the TELEPHONE TEST button.
2. Enter the Master User Code, and the system will display the
Telephone Test screen. The top portion of the screen shows
the actions that the Control Panel is taking. The bottom
portion of the screen shows the results of the actions. Scroll
through the status screen with the ↓ and ↑ arrows.
3. When the test is complete, press OK to return to the User Toolbox.
Restoring Programming Defaults
To soft reset the Control Panel back to the factory defaults, use the
Restore Default option in the Installer toolbox.
✓ NOTE: The Control Panel may also be “hard” reset to out-of-the-box factory
defaults by pressing and holding the emergency and home buttons while
applying power (if not disabled through programming questions Q-44 & Q-45).

Restore Defaults
The Restore Defaults screen provides a method to selectively reset the Control
Panel to its default programming values instead of using a full “hard” reset.
Two check box options are available; one or both must be checked: Figure 75. Restore Defaults Screen
• If the ZONES box is checked, all data for the 48 sensors will be erased and
replaced with the default values.
• If the CONSOLE box is checked, all the Control Panel programming
questions (except Z-Wave questions Q79-Q83) will be erased and replaced
with the default values. The User Codes will be erased, the backlight timeout
is reset to five minutes, and the brightness/volume settings are reset.
42
Regulatory Information & Limited Warranty
Wireless Product Notice Industry Canada Notices
Radio controls provide a reliable communications link and fill an NOTICE: The ringer equivalence number (REN) assigned to each
important need in portable wireless signaling; however, there are terminal device provides an indication of the maximum number of
some limitations which must be observed. terminals allowed to be connected to a telephone interface. The
• For U.S. installations only: The radios are required termination on an interface may consist of any combination of
to comply with FCC Rules and Regulations devices subject only to the requirement that the sum of the ringer
as Part 15 devices. As such, they have limited equivalence numbers of all the devices does not exceed 5.
transmitter power and therefore limited range. NOTICE: The Industry Canada label identifies certified equipment.
• A receiver cannot respond to more than one This certification means that the equipment meets certain
transmitted signal at a time and may be blocked by telecommunications network protective, operational and safety
radio signals that occur on or near their operating requirements. The Department does not guarantee the equipment
frequencies, regardless of code settings. will operate to the user’s satisfaction.
• Changes or modifications to the device Before installing this equipment, users should ensure that
may void FCC compliance. it is permissible to be connected to the facilities of the local
• Infrequently used radio links should be tested regularly telecommunications company. The equipment must also be
to protect against undetected interference or fault. installed using an acceptable method of connection. The customer
• A general knowledge of radio and its vagaries should be should be aware that compliance with the above conditions may
gained prior to acting as a wholesale distributor or dealer, and not prevent degradation of service in some situations.
these facts should be communicated to the ultimate users. Repairs to certified equipment should be made by an authorized
Canadian maintenance facility designated by the supplier. Any
FCC Notice
repairs or alterations made by the user to this equipment, or
This equipment generates and uses radio frequency energy and if
equipment malfunctions, may give the telecommunications
not installed and used properly, that is, in strict accordance with the
company cause to request the user to disconnect the equipment.
manufacturer’s instructions, may cause interference to radio and
television reception. It has been type tested and found to comply Users should ensure for their own protection that the electrical
with the limits for a Class B computing device in accordance with ground connections of the power utility, telephone lines and internal
Part 15 of FCC Rules, which are designed to provide reasonable metallic water pipe system, if present, are connected together. This
protection against such interference in a residential installation. precaution may be particularly important in rural areas.
However, there is no guarantee that interference will not occur in a CAUTION: Users should not attempt to make such connections
particular installation. If this equipment does cause interference to themselves, but should contact the appropriate electric inspection
radio or television reception, which can be determined by turning authority, or electrician, as appropriate.
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures: Limited Warranty
• Relocate the Console away from the TV/radio receiver. This 2gig Technologies Inc. product is warranted against defects
in material and workmanship for twelve (12) months. This
• Plug the Console into a different wall outlet so that
warranty extends only to wholesale customers who buy
the Console is on a different branch circuit.
through 2gig Technologies Inc. authorized distribution channels.
• Re-orient the TV/radio antenna. 2gig Technologies Inc. does not warrant this product to
• If necessary, the user should consult the consumers. Consumers should inquire from their selling dealer
dealer or an experienced radio/television as to the nature of the dealer’s warranty, if any. There are no
technician for additional suggestions. obligations or liabilities on the part of 2gig Technologies Inc.
FCC Telephone Rules and Regulations for consequential damages arising out of or in connection
The FCC requires that this alarm dialer system not make more with use or performance of this product or other indirect
than 15 repetitive dialing attempts to a single telephone number. damages with respect to loss of property, revenue, or profit,
There are no limitations when the calls are made sequentially or cost of removal, installation, or reinstallation. All implied
to two or more alternative numbers, or when these calls are warranties, including implied warranties for merchantability and
spaced 10 minutes apart to a single number. The FCC Rules implied warranties for fitness, are valid only until the warranty
and Regulations do not specify the re-attempt period as this can expires. This 2gig Technologies Inc. Warranty is in lieu of all
vary for specific applications. When setting this period, take into other warranties express or implied.
consideration local, interstate, foreign and special network call All products returned for warranty service require a Return Product
completion characteristics, network processing time, a sufficient Authorization Number (RPA#). Contact 2gig Technologies Inc. at
number of rings and busy/don’t answer modes. 866-670-1591 for an RPA# and other important details.

43
Reference Programming Question Table
Q# QUESTION DEFAULT Q# QUESTION DEFAULT
Q-1 Select RF sensor # (01-48) Q-28 Select quick exit (0-1) (1) enabled
Select RF sensor (#) type (00) unused Q-29 Enter periodic test, in days (0-255) 30 days
Varies by RF sensor type Q-31 Enter cancel time, in minutes (5-255) ‡ 5 minutes
Select RF sensor (#) equipment type
(Only shown for some sensor types) Q-32 Select cancel display (0-1) ‡ (1) enabled
Select RF sensor (#) equipment code (0000) other Q-33 Select cross sensor 47-48 (0-1) (0) disabled
Q-1 SUB-QUESTIONS

Q-46 Select trouble doesn’t sound at night (0-1) ♦ (1) enabled

Q-66 Select daylight saving (0-1) (1) enabled

44
Reference System Vocabulary Table
# WORD # WORD # WORD # WORD
002 ABORT 066 ELEVEN 130 LIGHT 194 SET
003 AC 067 EMERGENCY 131 LIGHTS 195 SEVEN
004 ACCESS 068 ENTER 132 LIQUOR 196 SEVENTEEN
005 ALARM 069 ENTRANCE 133 LIVING 197 SEVENTY
006 AND 070 ENTRY 134 LOADING 198 SHED
007 ANNOUNCEMENT 071 ERROR 135 LOCK 199 SHOP
008 AREA 072 EXERCISE 136 LOFT 200 SIDE
009 ARM 073 EXIT 137 LOW 201 SILENT
010 ARMED 074 EXIT NOW 138 MAIN 202 SIREN
011 ARMING 075 EXTERIOR 139 MAINTENANCE 203 SIX
012 AT 076 EXTERNAL 140 MASTER 204 SIXTEEN
013 ATTIC 077 FAILURE 141 MEDICAL 205 SIXTY
014 AUDIO 078 FAMILY 142 MEDICINE 206 SKYLIGHT
015 AUTO 079 FAN 143 MENU 207 SLIDING
016 AUTOMATION 080 FIFTEEN 144 MIDDLE 208 SMOKE
017 AUXILIARY 081 FIFTY 145 MONITOR 209 SOUNDER
018 AWAY 082 FIRE 146 MOTION 210 SOUTH
019 BABY’S 083 FIRE ALERT 147 MOTION DETECTOR 211 SPACE
020 BACK 084 FIRE DETECTOR 148 MUD 212 SPARE
021 BASEMENT 085 FIRST 149 NINE 213 STAIRS
022 BATHROOM 086 FIVE 150 NINETEEN 214 STAR
023 BATTERY 087 FLOOD 151 NINETY 215 STATUS
024 BEDROOM 088 FLOOR 152 NORTH 216 STAY
025 BONUS 089 FLUID 153 NOT 217 STOP
026 BREAK 090 FOIL 154 NOT READY 218 STORAGE
027 BUTTON 091 FOR 155 NO DELAY 219 STUDY
028 BYPASS 092 FORTY 156 NO ENTRY DELAY 220 SUMP
029 BYPASSED 093 FOUR 157 NURSERY 221 SUPERVISION
030 CABINET 094 FOURTEEN 158 OFF 222 SYSTEM
031 CANCEL 095 FOURTH 159 OFFICE 223 TAMPER
032 CARBON MONOXIDE 096 FREEZE 160 ON 224 TEMPERATURE
033 CELLAR 097 FREEZER 161 ONE 225 TEN
034 CELLULAR 098 FRONT 162 ONE HUNDRED 226 TERMINATED
035 CELL RADIO 099 FURNACE 163 OUTPUT 227 THERMOSTAT
036 CENTER 100 GAME 164 OUTSIDE 228 THIRD
037 CHECK 101 GARAGE 165 PANEL 229 THIRTEEN
038 CHEST 102 GAS 166 PANIC 230 THIRTY
039 CHILDREN’S 103 GLASS 167 PANTRY 231 THREE
040 CHIME 104 GLASS BREAK 168 PATIO 232 TO
041 CLOSET 105 GUEST 169 PERIMETER 233 TOOL
042 CODE 106 GUN 170 PHONE LINE 234 TRANSMITTED
043 COMMUNICATIONS 107 HALL 171 PLAY 235 TRANSMITTER
044 COMPUTER 108 HALLWAY 172 POLICE 236 TROUBLE
045 CONTROL 109 HANGING 173 POOL 237 TURN
046 COOL 110 HANG UP 174 POUND 238 TWELVE
047 CRAWL 111 HEAT 175 POWER 239 TWENTY
048 CURRENT 112 HIGH 176 PRESS 240 TWO
049 DAY 113 HOME 177 PREVIOUS 241 UNLOCK
050 DEGREES 114 HOUSE 178 PUMP 242 UPPER
051 DEN 115 ICE 179 RADIO 243 UPSTAIRS
052 DETECTOR 116 INSIDE 180 READY 244 USER
053 DIM 117 INSTANT 181 REAR 245 UTILITY
054 DINING 118 INTERIOR 182 RELAY 246 VALVE
055 DISARM 119 INTRUSION 183 REMOTE 247 VOICE
056 DISARMED 120 IS 184 REPEAT 248 WALL
057 DOCK 121 KEY 185 RF JAM 249 WATER
058 DOOR 122 KEYFOB 186 RIGHT 250 WEST
059 DOWNSTAIRS 123 KEYPAD 187 ROOM 251 WINDOW
060 DRIVEWAY 124 KIDS 188 SAFE 252 WIRELESS
061 EAST 125 KITCHEN 189 SECOND 253 YARD
062 EIGHT 126 LAUNDRY 190 SECURITY 254 ZERO
063 EIGHTEEN 127 LEFT 191 SENSOR 255 ZONE
064 EIGHTY 128 LEVEL 192 SENSORS
065 ELECTRIC 129 LIBRARY 193 SESSION

45
Index
#’s D
2GIG-AC1 replacement power supply 7 Daylight saving end month 36
2GIG-ANT1 internal GSM antenna 7 Daylight saving end Sunday 36
2GIG-ANT1X external in-wall GSM antenna 7 Daylight saving scheme 36
2GIG-ANT2X external attic mount GSM antenna 7 Daylight saving start month 36
2GIG-ANT4X 7 Daylight saving start Sunday 36
2GIG-BATT1 standard battery pack 7 Day Zone sensor type 18
2GIG-BATT1X extended battery pack 7 DELETE button 15
2GIG-DW10 thin door/window contact 6 Dialer enable 30
2GIG-DW20R recessed door contact 6 Dialing prefix 30
2GIG-GB1 glass break detector 6 Dialing type 31
2GIG-GSMx GSM module 7 Disable siren after 2-way audio 38
2GIG-KEY1 4-button key ring remote 6 Disarming with key fob alert after alarm 36
2GIG-PANIC1 panic button remote 6 Download csid 34
2GIG-PIR1 passive infrared motion detector 6
2GIG-SMKT2 smoke and heat detector 6 E
2GIG-TAKE-345 6 Emergency button 31
2GIG-TS1 Wireless touch screen keypad 6 END button 15
2-way voice central station commands 30 Entry delay 1 30
2-way voice enable 30 Entry delay 2 30
4-button key ring remote 6 ESC button 15
24-hour Audible Alarm sensor type 18 ETL Listing 2
24-hour Auxiliary Alarm sensor type 18 Event log 37
24-hour Carbon Monoxide sensor type 18 EXIT button 15
24-hour Fire sensor type 18 Exit delay 30
24-hour Fire with Verification sensor type 18 Exit delay restart 32
24-hour Silent Alarm sensor type 18 Exit/Entry 1 sensor type 18
Exit/Entry 2 sensor type 18
A Exiting programming 39
Abort window dialer delay 32 Extended battery pack 7
AC loss detect time 33 External attic mount GSM antenna 7
AC loss reports 35 External in-wall GSM antenna 7
AC loss report time 33
AC power icon 14 F
AC restore reports 35 Fire bell cutoff 33
Alarm restore reports 35 Fire emergency key 31
Alarm sounder 9 Force bypass reports 37
Alarm system permit 2 FWD button 15
Arming screen 12
Auto stay 31
G
Glass break detector 6
B GO TO button 15
BACK button 15 GSM module 7
Backlight timeout 39 GSM module installation 10
Backup battery connection 11 GSM radio icon 14
Backup battery status icon 14 GSM radio test 42
Bell terminals 9
BKSP button 15
Block diagram 3 H
Brightness / volume 39 Hardwired loops 8
Burglary bell cutoff 32 Home screen 12
Bypass restore reports 35
I
C INSERT button 15
Call waiting disable code 30 Installation outline 5
Cancel display 32 Installer code 33
Cancel time 32 Installer code entry 13
Central station #1 account number 30 Installer programming 20, 22
Central station #1 phone number 30 Installer toolbox 13
Central station #2 account number 33 Insurance discounts 2
Central station #2 phone number 33 Interior follower sensor type 18
Central station commands for 2-way voice 30 Interior sensor open icon 14
Closing reports 35 Interior with delay sensor type 18
Communicator telephone line 9 Internal GSM antenna 7
Control panel external features 4
Control panel features 4 K
Control panel internal features 4 Key fob # 27
Control panel location 5 Key fob arm / disarm confirmation 36
Control panel location height 5 Key fob arm no delay 27
Control panel mounting 11 Key fob emergency key 27
Control panel mounting plate 8 Key fob equipment age 27
Control panel wiring 11 Key fob equipment code 27
Control panel wiring diagram 2 Key fob key 2 can disarm 27
Cross sensor 32 Key fob key 4 output 27
Cross sensor timeout 32 Key fob serial number 27
CS Lack of usage notification time 31 key fob summary screen 26
Key fob voice descriptor 27

L
LEARN button 15
Location of sensors 5
Lock default programming 34
Lock installer programming 34

M
Manual bypass reports 34
Master user access to Z-Wave Toolbox 38

46
Index
Menu screen 12 Set date / time 39
SET TIME button 39
N SHIFT button 15
Navigation arrows 15 Signal strength indicators 41
NFPA Standard #72 ii Silent burglary sensor type 18
No response sensor type 18 Silent panic/burglary listen only 30
Siren supervision time 31
SKIP button 15
O Smart test reports 36
Open collector output selection 37 Smoke and heat detector 6
Opening reports 35 Smoke detector location ii
Solid state output 9
P Sounder disable/enable 40
Panic button remote 6 Sounder disable icon 14
Passive infrared motion detector 6 Standard battery pack 7
PASTE button 15 Status screen 12
Perimeter sensor type 18 SUM button 15
Periodic test timer 32 Super switch wireless takeover module 6
Phone fail detect 35 Swinger shutdown count 31
Phone line failure icon 14 System block diagram 3
Police emergency key 31 System configuration screen 13
Power supply mounting 11 System low battery reports 35
Power supply wiring 11 System low battery restore reports 35
Programming mode entry reports 34 System sensor types 18
Programming outline 16 System status icons 14
Programming question list 17 System tamper causes trouble 36
System vocabulary 19
Q
Quick arming 31 T
Quick bypass 36 Takeover module 6
Quick exit 32 Telephone line 9
Telephone test 42
Temperature display units 37
R Testing the system 40
Radio modem network failure causes trouble 31
Test mode icon 14
Radio modem network failure reports 31
Thin door/window contact 6
Radio modem network failure time 31
Toolbox screens 13
Radio status mode 42
Touch screen keypad traffic icon 14
Recessed door contact 6
Trouble doesn’t sound at night 34
Reference programming question table 44
Trouble reports 34
Reference system vocabulary 45
Trouble resound after holdoff 34
Regulatory information 43
Trouble restore reports 35
Remote control phone enable 33
Replacement power supply 7
Restoring programming defaults 42 U
RF jam causes trouble 36 Unused zone 18
RF key fob programming 26 User Management 39
RF key fob programming outline 26
RF key fob programming steps 27 V
RF key fob summary screen 26 Vocabulary 19
RF keypad # 29
RF keypad emergency key 29
RF keypad equipment age 29 W
RF keypad equipment code 29 Walk test mode 41
RF keypad other equipment code 29 Wall mounting control panel 8
RF keypad programming 28 Wired sensor # 25
RF keypad programming outline 28 Wired sensor chime 25
RF keypad programming steps 29 Wired sensor dialer delay 25
RF keypad serial number 29 Wired sensor equipment code 25
RF keypad summary screen 28 Wired sensor equipment type 25
RF keypad voice descriptor 29 Wired sensor normal state 25
RF low battery reports 35 Wired sensor programming 24
RF low battery restore reports 35 Wired sensor programming outline 24
RF sensor # 22 Wired sensor programming steps 25
RF sensor chime 23 Wired sensor reports 25
RF sensor dialer delay 23 Wired sensor summary screen 24
RF sensor equipment age 23 Wired sensor type 25
RF sensor equipment code 22 Wired sensor voice descriptor 25
RF sensor equipment type 22 Wireless installation tips 5
RF sensor loop number 23 Wireless keypad 6
RF sensor other equipment code 22 Wireless sensor installation 8
RF sensor programming 20 Wireless takeover module 6
RF sensor programming outline 20 Wireless touch screen keypad 6
RF sensor programming steps 22 Wiring diagram 2
RF sensor reports 23
RF sensor serial number 23 Z
RF sensor summary screen 21 Zone reporting test 40
RF sensor supervised 23 Zone types 18
RF sensor type 22 Z-Wave door locks feature 37
RF sensor voice descriptor 23 Z-Wave feature enable 37
RJ31X telephone jack 9 Z-Wave switches feature 37
Z-Wave thermostats feature 37
S
Saving programming 39
Security screen 12
Sensor signal loss through materials 5
Sensor types 18
Sensor zones 18
Services menu requires master code 38

CAN and FPGA Communication Engineering: Implementation of a CAN Bus based Measurement System on an FPGA Development Kit
From Everand
CAN and FPGA Communication Engineering: Implementation of a CAN Bus based Measurement System on an FPGA Development Kit
Yu Zhu
No ratings yet
Sonajero Osos
No ratings yet
Sonajero Osos
3 pages
2020 - ICMM - Tailings Governance Framework - Position Statement
No ratings yet
2020 - ICMM - Tailings Governance Framework - Position Statement
7 pages
UNIVERGE SV9100 Hardware Manual - Issue 9.1
No ratings yet
UNIVERGE SV9100 Hardware Manual - Issue 9.1
574 pages
Remote Display and Control Panel: Installation Manual
No ratings yet
Remote Display and Control Panel: Installation Manual
49 pages
Manual Instalare Ability
100% (1)
Manual Instalare Ability
72 pages
Instruction Book Iqan-Xa2: Publ No HY17-8385-IB/UK Edition 0505
No ratings yet
Instruction Book Iqan-Xa2: Publ No HY17-8385-IB/UK Edition 0505
38 pages
2GIG Go!Control - Installation and Programming Guide (Archive)
No ratings yet
2GIG Go!Control - Installation and Programming Guide (Archive)
52 pages
Taktis Consultant Specifications
No ratings yet
Taktis Consultant Specifications
25 pages
PC1616-1832-1864 Installation Manual ENG 29008247R002
No ratings yet
PC1616-1832-1864 Installation Manual ENG 29008247R002
72 pages
Aparat US Petrea SCOUT 55
No ratings yet
Aparat US Petrea SCOUT 55
64 pages
IDS805 Installer Manual
No ratings yet
IDS805 Installer Manual
48 pages
V 20 II
No ratings yet
V 20 II
120 pages
DSC PS1864 ProgrammingManual
No ratings yet
DSC PS1864 ProgrammingManual
72 pages
HA-266 6-ZONE ALARM CONTROL PANEL OWNER'S MANUAL. Programming and Operation FOR HOME AND OFFICE PROTECTIONS WITH AUTO-DIALER AND COMMUNICATOR
No ratings yet
HA-266 6-ZONE ALARM CONTROL PANEL OWNER'S MANUAL. Programming and Operation FOR HOME AND OFFICE PROTECTIONS WITH AUTO-DIALER AND COMMUNICATOR
38 pages
3G2080 TL2803G Reference-Manual-Extended R001 en
No ratings yet
3G2080 TL2803G Reference-Manual-Extended R001 en
52 pages
Operating Manual: Air Band Transceiver
No ratings yet
Operating Manual: Air Band Transceiver
56 pages
Sigma Mod: Installation and Start-Up Instructions
No ratings yet
Sigma Mod: Installation and Start-Up Instructions
59 pages
Becker SK22003CT SK 22003 CT Nord Manual Datasheet
No ratings yet
Becker SK22003CT SK 22003 CT Nord Manual Datasheet
76 pages
Integra Plus P en 5c1f6db6 PDF
No ratings yet
Integra Plus P en 5c1f6db6 PDF
102 pages
SV9100 Hardware Manual GE 5 0
No ratings yet
SV9100 Hardware Manual GE 5 0
564 pages
SV9100 - Hardware Manual - GE - 5 - 0 PDF
No ratings yet
SV9100 - Hardware Manual - GE - 5 - 0 PDF
564 pages
User Guide For Stargate Bluetower v5 3
No ratings yet
User Guide For Stargate Bluetower v5 3
192 pages
A6V10406110
No ratings yet
A6V10406110
56 pages
Impassa-SCW9055-57 V1.0 - Manual Instalare PDF
No ratings yet
Impassa-SCW9055-57 V1.0 - Manual Instalare PDF
84 pages
802CIBN0102en PDF
No ratings yet
802CIBN0102en PDF
142 pages
GF-9900 Transmitter-Manual
No ratings yet
GF-9900 Transmitter-Manual
64 pages
9900 SmartPro Manual PDF
No ratings yet
9900 SmartPro Manual PDF
64 pages
Ca5u e
No ratings yet
Ca5u e
24 pages
SV9100_Hardware_Manual_GE_2_0
No ratings yet
SV9100_Hardware_Manual_GE_2_0
556 pages
FC100 200 Install
No ratings yet
FC100 200 Install
100 pages
BA067DEN Fieldcheck OM
No ratings yet
BA067DEN Fieldcheck OM
72 pages
1769-Sdn Devicenet Scanner Module: Catalog Numbers 1769-Sdn User Manual
No ratings yet
1769-Sdn Devicenet Scanner Module: Catalog Numbers 1769-Sdn User Manual
156 pages
728-738 Install Manual V2.20
100% (1)
728-738 Install Manual V2.20
37 pages
Vista-120 Installation Manual
No ratings yet
Vista-120 Installation Manual
176 pages
873 I - O Manual
100% (1)
873 I - O Manual
52 pages
Factorytalk Alarms and Events System Configuration Guide: Technical Publications
No ratings yet
Factorytalk Alarms and Events System Configuration Guide: Technical Publications
213 pages
TS700 User
No ratings yet
TS700 User
16 pages
PERFECTA 16, PERFECTA 16-WRL, PERFECTA 32, PERFECTA 32-WRL - Installer Manual - 07 - 20 - EN
No ratings yet
PERFECTA 16, PERFECTA 16-WRL, PERFECTA 32, PERFECTA 32-WRL - Installer Manual - 07 - 20 - EN
31 pages
Rd8200 Om Eng
No ratings yet
Rd8200 Om Eng
70 pages
Express: Esprit
No ratings yet
Express: Esprit
36 pages
TS900 User
No ratings yet
TS900 User
56 pages
Device Net
No ratings yet
Device Net
156 pages
Installation Manual EnUS 2500893963
No ratings yet
Installation Manual EnUS 2500893963
112 pages
Conventional Fire Alarm
No ratings yet
Conventional Fire Alarm
24 pages
Smoke Control Trane
100% (2)
Smoke Control Trane
156 pages
TS790 User)
No ratings yet
TS790 User)
57 pages
User Guide VoiceBlue Next v3.1
No ratings yet
User Guide VoiceBlue Next v3.1
92 pages
Impassa-SCW9057 V1-1 IM EN Rev4 PDF
No ratings yet
Impassa-SCW9057 V1-1 IM EN Rev4 PDF
88 pages
7 - Murphy Power Ignition - Mpi 16 - Install Maintenance
No ratings yet
7 - Murphy Power Ignition - Mpi 16 - Install Maintenance
129 pages
Engineered Smoke Control System-Trace
100% (2)
Engineered Smoke Control System-Trace
156 pages
ZX200 Install Manual
100% (1)
ZX200 Install Manual
56 pages
Manuale DI Installazione E Programmazione: Installation AND Programming Manual
No ratings yet
Manuale DI Installazione E Programmazione: Installation AND Programming Manual
88 pages
Yb110/Yb230 Fireye Burnerlogix: Description
No ratings yet
Yb110/Yb230 Fireye Burnerlogix: Description
62 pages
CNC Machining Handbook: Building, Programming, and Implementation
From Everand
CNC Machining Handbook: Building, Programming, and Implementation
Alan Overby
No ratings yet
Teardowns: Learn How Electronics Work by Taking Them Apart
From Everand
Teardowns: Learn How Electronics Work by Taking Them Apart
Bryan Bergeron
No ratings yet
Correct Maintenance - Cognex DataMan 8500
From Everand
Correct Maintenance - Cognex DataMan 8500
Unique Content
No ratings yet
Arduino + Android Projects for the Evil Genius: Control Arduino with Your Smartphone or Tablet
From Everand
Arduino + Android Projects for the Evil Genius: Control Arduino with Your Smartphone or Tablet
Simon Monk
4.5/5 (2)
Smart Card Applications: Design models for using and programming smart cards
From Everand
Smart Card Applications: Design models for using and programming smart cards
Wolfgang Rankl
No ratings yet
Securing ChatGPT: Best Practices for Protecting Sensitive Data in AI Language Models
From Everand
Securing ChatGPT: Best Practices for Protecting Sensitive Data in AI Language Models
Matthew C. Smith
No ratings yet
Programming Arduino Next Steps: Going Further with Sketches
From Everand
Programming Arduino Next Steps: Going Further with Sketches
Simon Monk
3/5 (3)
DC/DC Converter Handbook: SMPS topologies from an EMC point of view
From Everand
DC/DC Converter Handbook: SMPS topologies from an EMC point of view
Andreas Nadler
No ratings yet
Midterm Exam Differential 231
No ratings yet
Midterm Exam Differential 231
25 pages
AU Optronics B173RW01 Ver 5
No ratings yet
AU Optronics B173RW01 Ver 5
31 pages
soal bahasa inggris
No ratings yet
soal bahasa inggris
6 pages
Siporex Brochure
No ratings yet
Siporex Brochure
7 pages
Kac - 1977 - Lie Superalgebras
No ratings yet
Kac - 1977 - Lie Superalgebras
89 pages
Decentering
No ratings yet
Decentering
14 pages
X X + (X - X) + (X - X) (Observation) Overall Sample
No ratings yet
X X + (X - X) + (X - X) (Observation) Overall Sample
9 pages
Timing Belt, Gear and Pulleys Opel Zafira-B
No ratings yet
Timing Belt, Gear and Pulleys Opel Zafira-B
4 pages
Geron, Salazar, Halili, Terui, Andes
No ratings yet
Geron, Salazar, Halili, Terui, Andes
6 pages
AL-6XN Sourcebook
No ratings yet
AL-6XN Sourcebook
59 pages
Cell Search Techniques in LTE Paper
No ratings yet
Cell Search Techniques in LTE Paper
10 pages
Proprietes Mexaniques
No ratings yet
Proprietes Mexaniques
9 pages
Revised High Pressure Water Blasting Procedure Rev 070220
No ratings yet
Revised High Pressure Water Blasting Procedure Rev 070220
19 pages
Egan's Irish Whiskey - Case Report
No ratings yet
Egan's Irish Whiskey - Case Report
13 pages
Cessna 172 RG Checklist Cessna 172 RG Checklist Cessna 172 RG Checklist
No ratings yet
Cessna 172 RG Checklist Cessna 172 RG Checklist Cessna 172 RG Checklist
2 pages
Demag All Terrain Cranes Spec 032383
No ratings yet
Demag All Terrain Cranes Spec 032383
36 pages
Cuestionario VIA de Fortalezas Personales
No ratings yet
Cuestionario VIA de Fortalezas Personales
4 pages
NOMA SIC Cancellation
No ratings yet
NOMA SIC Cancellation
60 pages
Ey Winning The Path To Net Zero
No ratings yet
Ey Winning The Path To Net Zero
52 pages
ĐỀ HSG THÁNG 11- THANH
No ratings yet
ĐỀ HSG THÁNG 11- THANH
9 pages
Enviro - News ARAMCO
No ratings yet
Enviro - News ARAMCO
56 pages
(Graduate Studies in Mathematics) N. V. Krylov-Introduction To The Theory of Random Processes-Amer Mathematical Society (2002) PDF
100% (2)
(Graduate Studies in Mathematics) N. V. Krylov-Introduction To The Theory of Random Processes-Amer Mathematical Society (2002) PDF
247 pages
Towards Sustainable Water Management in Sohar
No ratings yet
Towards Sustainable Water Management in Sohar
48 pages
Process Control - Threads: Flexial Quality Procedure QP158
No ratings yet
Process Control - Threads: Flexial Quality Procedure QP158
2 pages
ME KZ RE Ds CMP3 - SMP3 EN 230718
No ratings yet
ME KZ RE Ds CMP3 - SMP3 EN 230718
2 pages
Final Glass Furniture
No ratings yet
Final Glass Furniture
26 pages
MRTS71 Superseded
No ratings yet
MRTS71 Superseded
13 pages
Nine Insights On Sound Healing
100% (3)
Nine Insights On Sound Healing
13 pages