GEOMATE SG7 GNSS

User Guide
 Table of Content

Table of Content

Table of Content ................................................................................................................ 2

Preface .............................................................................................................................. 5
Copyright ................................................................................................................................. 5
Safety Warnings ....................................................................................................................... 5
FCC Interference Statement .................................................................................................... 5
CE Interference Statement ...................................................................................................... 6
1 Introduction ................................................................................................................ 7
1.1 Safety Information ............................................................................................... 7
1.1.1 Warnings and Cautions........................................................................................ 7
1.2 Regulations and Safety ........................................................................................ 7
1.2.1 Use and Care........................................................................................................ 8
1.3 Technical Support................................................................................................. 8
1.4 Disclaimer ............................................................................................................ 8
1.5 Your Comments ................................................................................................... 8
2 Getting Started with SG7 ............................................................................................. 8
2.1 About the Receiver .............................................................................................. 8
2.2 Parts of the Receiver ........................................................................................... 9
2.2.1 Front Panel .......................................................................................................... 9
2.2.2 Lower Housing ................................................................................................... 11
2.2.3 Receiver Ports .................................................................................................... 11
2.3 Batteries and Power .......................................................................................... 13
2.3.1 Batteries ............................................................................................................ 13
2.3.2 The Internal Battery........................................................................................... 13
2.3.3 Battery Safe ....................................................................................................... 14
2.3.4 External Power Supply ....................................................................................... 15
2.4 Inserting SIM Card ............................................................................................. 16
2.5 Product Basic Supply Accessories ...................................................................... 17
2.5.1 Base Kit Basic Supply ......................................................................................... 17
2.5.2 Rover Kit Basic Supply ....................................................................................... 18
2.6 Connecting to an Office Computer .................................................................... 19
2.7 Downloading Logged Data................................................................................. 20
2.7.1 FTP Download .................................................................................................... 20
2.7.2 Web Server Download ....................................................................................... 21
2.7.3 USB Download ................................................................................................... 22
3 Front Panel Operation ............................................................................................... 24
3.1 Main Operation Menus ..................................................................................... 24

GEOMATE SG7 GNSS USER GUIDE | 2022-04 Page | 2

 Table of Content

3.2 Configure the Working Mode ............................................................................ 27

4 Equipment Setup and Operation ................................................................................ 32
4.1 Post-processing Base Station Setup .................................................................. 32
4.2 Real-Time Base Station Setup ............................................................................ 34
4.2.1 Internal Cellular or UHF ..................................................................................... 34
4.2.2 External UHF ...................................................................................................... 35
4.3 Real-Time Rover Station Setup .......................................................................... 38
4.4 Notes of using tilt measurement..................................................................................... 40
5 Configuring Through a Web Browser ............................................................................. 41
5.1 Status Menu ...................................................................................................... 43
5.1.1 Position Submenu.............................................................................................. 43
5.1.2 Activity Submenu............................................................................................... 43
5.1.3 Google Map Submenu ....................................................................................... 44
5.2 Satellites Menu .................................................................................................. 45
5.2.1 Tracking Table Submenu .................................................................................... 45
5.2.2 Tracking Info. Table Submenu ............................................................................ 46
5.2.3 Tracking Skyplot Submenu ................................................................................. 46
5.2.4 Satellite Activation Submenu ............................................................................ 47
5.3 Receiver Configuration Menu ........................................................................... 48
5.3.1 Description ........................................................................................................ 48
5.3.2 Antenna Configuration Submenu ...................................................................... 49
5.3.3 Reference Station Settings Submenu ................................................................ 49
5.3.4 Receiver Reset Submenu ................................................................................... 52
5.3.5 Languages Submenu .......................................................................................... 52
5.3.6 User Management Submenu............................................................................. 53
5.3.7 HCPPP Settings .................................................................................................. 53
5.4 Data Recording Menu........................................................................................ 54
5.4.1 Log Settings Submenu ....................................................................................... 54
5.4.2 FTP Push Settings Submenu .............................................................................. 56
5.4.3 FTP Push Log Submenu...................................................................................... 57
5.4.4 Data Download Submenu.................................................................................. 58
5.5 IO Settings Menu ............................................................................................... 60
5.5.1 IO Settings Submenu ......................................................................................... 60
5.6 Network Setting Menu ...................................................................................... 67
5.6.1 Description Submenu ........................................................................................ 67
5.6.2 Mobile Network Setting Submenu .................................................................... 68
5.6.3 Email Alarm Submenu ....................................................................................... 68
5.6.4 HTTP Submenu .................................................................................................. 69
5.6.5 HTTPS Submenu ................................................................................................ 70
5.6.6 FTP Service Submenu ........................................................................................ 70
5.7 Module Setting Menu........................................................................................ 71

GEOMATE SG7 GNSS USER GUIDE | 2022-04 Page | 3

 Table of Content

5.7.1 Description Submenu ........................................................................................ 71

5.7.2 WiFi Submenu ................................................................................................... 71
5.7.3 Bluetooth Settings Submenu ............................................................................. 72
5.7.4 Radio Settings Submenu .................................................................................... 73
5.8 Firmware Menu ................................................................................................. 74
5.8.1 Firmware Info Submenu .................................................................................... 74
5.8.2 Hardware Version Submenu .............................................................................. 74
5.8.3 Config File Submenu .......................................................................................... 75
5.8.4 System Log Download Submenu ....................................................................... 75
5.8.5 User Log Submenu............................................................................................. 75
5.8.6 Firmware Update Submenu ............................................................................... 76
5.8.7 GNSS Board Upgrade Submenu......................................................................... 77
5.8.8 Radio Upgrade Submenu ................................................................................... 77
5.8.9 Upgrade Online Submenu ................................................................................. 77
5.8.10 GNSS Registration Submenu.............................................................................. 78
5.9 Cloud Service Setting Menu ............................................................................................ 79
5.9.1 Cloud Service Setting Submenu ................................................................................. 79
A Communication Ports Definition ................................................................................... 80
AI GEOMATE SG7 Receiver IO Port (7-pin Lemo Port) Definition ......................................... 80

GEOMATE SG7 GNSS USER GUIDE | 2022-04 Page | 4

 Preface

Preface

Copyright

Copyright 2016-2017

GEOMATE POSITIONING PTE. LTD. All rights reserved. All other trademarks are the property
of their respective owners.

Trademarks

All product and brand names mentioned in this publication are trademarks of their respective
holders.

Safety Warnings

The Global Positioning System (GPS) is operated by the U.S. Government, which is solely
responsible for the accuracy and maintenance of the GPS network. Accuracy can also be
affected by poor satellite geometry and obstructions, like buildings and heavy canopy.

FCC Interference Statement

This equipment has been designed to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules in the Portable Mode. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.

Operation is subject to the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference received, including interference
that may cause undesired operation.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 Page | 5

 Preface

CE Interference Statement

The SG7 GNSS receiver is in compliance with the essential requirements and other
relevant provisions of Directive 2014/53/EU.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 Page | 6

 Introduction

1 Introduction

The SG7 GNSS Receiver User Guide describes how to set up and use the GEOMATE® SG7 GNSS
receiver. In this manual, “the receiver” refers to the SG7 GNSS receiver unless otherwise
stated. Even if you have used other Global Navigation Satellite Systems (GNSS) products
before, GEOMATE recommends that you spend some time reading this manual to learn
about the special features of this product. If you are not familiar with GNSS, go to
www.GEOMATEnav.co m for an interactive look at GEOMATE and GNSS.

1.1 Safety Information

1.1.1 Warnings and Cautions

An absence of specific alerts does not mean that there are no safety risks involved.

A Warning or Caution information is intended to minimize the risk of personal injury and/or
damage to the equipment.

WARNING - A Warning alerts you to a potential misused or wrong setting of the

equipment.

CAUTION - A Caution alerts you to a possible risk of serious injury to your person and/or
damage to the equipment.

1.2 Regulations and Safety

The receivers contain a built-in wireless modem for signal communication through Bluetooth®
wireless technology or through external communication datalink. Regulations regarding the
use of the wireless modem vary greatly from country to country. In some countries, the unit
can be used without obtaining an end-user license. However, in some countries, the
administrative permissions are required. For license information, consult your local dealer.
Bluetooth® operates in license-free bands.

Before operating a SG7 GNSS receiver, determine if authorization or a license to operate the
unit is required in your country. It is the responsibility of the end-user to obtain an operator's
permit or license for the receiver for the location or country of use.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 Page | 7

 Getting Started with
SG7

1.2.1 Use and Care

This receiver is designed to withstand the rough environment that typically occurs in the field.
However, the receiver is high-precision electronic equipment and should be treated with
reasonable care.

CAUTION - Operating or storing the receiver outside the specified temperature range
will cause irreversible damage.

1.3 Technical Support

If you have a problem and cannot find the information you need in this manual or GEOMATE
website (www.geomate.sg), contact your local GEOMATE dealer from which you purchased
the receiver(s).

1.4 Disclaimer

Before using the receiver, please make sure that you have read and understood this User Guide,
as well as the safety information. GEOMATE holds no responsibility for the wrong operation by
users and for the losses incurred by the wrong understanding about this User Guide.
However, GEOMATE reserves the rights to update and optimize the contents in this guide
regularly. Please contact your local GEOMATE dealer for new information.

1.5 Your Comments

Your feedback about this user guide will help us to improve it in future revision.
2 Getting Started with SG7

2.1 About the Receiver

The new GEOMATENAV SG7 GNSS receiver offers integrated IMU-RTK technology to provide a
robust and accurate GNSS positioning in any circumstances. Unlike the standard MEMS
based GNSS receivers, the SG7 GNSS IMU-RTK combines state-of-the-art GNSS RTK engine,
calibration-free professional IMU sensor and advanced GNSS tracking capabilities. Survey
projects are achieved with high productivity and reliability pushing the boundaries of
conventional GNSS RTK survey.
GEOMATE SG7 GNSS USER GUIDE | 2022-04 Page | 8
 Getting Started with
SG7
The LCD panel enables user to check satellite-tracking status, internal battery status, Wi-Fi
status, working mode, data logging status and basic receiver information. Bluetooth and Wi-Fi
technology provides cable-free communication between the receiver and controller.

The receiver can be used as the part of an RTK GNSS system with GEOMATE MateSurvey
software. Moreover, user can download the GNSS data that recorded in the internal memory
of receiver to a computer.

The receiver can be used as the part of an RTK GNSS system with GEOMATE MateSurvey
software. And you can download the GNSS data that recorded in the internal memory of
receiver to a computer.

To configure the receiver for performing a wide variety of functions, you can use the web
interface by connecting the receiver with PC or smartphone through Wi-Fi.

2.2 Parts of the Receiver

The operating controls are all located on the front panel. SIM card slot is on the backside. Serial
ports and connectors are located on the bottom of the unit.

2.2.1 Front Panel

The following figure shows a front view of the receiver.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 Page | 9

 Getting Started with
SG7

Front panel

The front panel contains two indicator LEDs and two buttons.

Satellite LED Correction LED

Function button Power button

Name Description

Correction LED  Indicates whether the receiver is transmitting/receiving

(Yellow/Green) differential data.
 As a Base station: successfully transmitting differential
data, flash yellow light.
 As a Rover station: successfully receiving differential data
from Base station will flash yellow light when it is single or
float, flash green light when it is fixed.

Satellite LED (Blue)  Shows the number of satellites that the receiver has
tracked.
 When the receiver is searching satellites, the blue LED
flashes once every 5 seconds.
 When the receiver has tracked N satellites, the blue LED
will flash N times every 5 seconds.

Fn button (White)  Move to next line of the menus or options.

 Move to next character of the value that you want to
make change.
 Cancel the change you make on a function.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 10

 Getting Started with
SG7

Power button  Works as a Power button:

(White)  Press and hold this button for 3 seconds to turn on or turn
off the receiver.
 Works as a Confirmbutton
 Hold Fn button and press this button for 5 times
continuously to reset the mainboard.

2.2.2 Lower Housing

The lower housing contains one SIM card slot, one TNC radio antenna connector, one
communication and power port and one USB type C communication and power port.

IO serial communication and TNC radio antenna connector

power port

SIM card slot

USB communication and

power port

2.2.3 Receiver Ports

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 11

 Getting Started with
SG7

Port Name Description

IO port  This port is a 7-pin LEMO connector that

supports RS-232 communications and
external power input.
 Users can use HCE600 Type-c Cable supplied
with the system to realize RS-232
communications between the receiver and
computer or controller. Also, users can use a
7-pin cable to transmit differential data to an
external radio.

USB port  This port is a type-C USB connector that

supports USB communications.
 Users can use USB Cable supplied with the
system to download the logged data to a
computer.

Radio antenna  Connect a radio antenna to internal radio of

connector the receiver. And this connector is not used if
you are using an external radio.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 12

 Getting Started with
SG7
2.3 Batteries and Power

2.3.1 Batteries

The receiver has an built-in non-removable Lithium‑ion battery.

2.3.2 The Internal Battery

The rechargeable Lithium-ion battery is supplied partially charged.

WARNING – Charge and use the rechargeable Lithium-ion battery only in strict
accordance with the instructions. Charging or using the battery in unauthorized equipment
can cause an explosion or fire and can result in personal injury and/or equipment damage.

To prevent injury or damage:

•Do not charge or use the battery if it appears to be damaged or leaking.

•Charge the Lithium-ion battery only in a GEOMATE product that is specified to charge it. Be
sure to follow all instructions that are provided with the battery charger.

•Discontinue charging a battery that gives off extreme heat or a burning odor.

•Use the battery only in GEOMATE equipment that is specified to use it.

•Use the battery only for its intended use and according to the instructions in the product
documentation.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 13

 Getting Started with
SG7

2.3.3 Battery Safe

WARNING – Do not damage the rechargeable Lithium-ion battery. A damaged battery

can cause an explosion or fire and can result in personal injury and/or property damage.

To prevent injury or damage:

•Do not use or charge the battery if it appears to be damaged. Signs of damage include, but
are not limited to discoloration, warping, and leaking battery fluid.

•Do not expose the battery to fire, high temperature, or direct sunlight.

•Do not immerse the battery in water.

•Do not use or store the battery inside a vehicle under hot weather condition.

•Do not drop or puncture the battery.

•Do not open the battery or short-circuit its contacts.

WARNING – Avoid contact with the rechargeable Lithium-ion battery if it appears to be

leaking. Battery fluid is corrosive and contact with it can result in personal injury and/or
property damage.

To prevent injury or damage:

•If the battery leaks, avoid with the battery fluid.

•If battery fluid gets into your eyes, immediately rinses your eyes with clean water and seek
medical attention. Please do not rub your eyes!

•If battery fluid gets onto your skin or clothing, immediately use clean water to wash off the
battery fluid.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 14

 Getting Started with
SG7

2.3.4 External Power Supply

Two methods are available for providing the external power to the receiver by the GPS to PC Data
Cable+ Power Adapter, or GPS to PC Data Cable + external power cable (option purchase)
+ vehicle battery. In

the office:

The Power Adapter is connecting with AC power of 100-240V, the output port of the Power
Adapter connects with the Power Port of the GPS to PC Data Cable.

In the field:

The external power cable is connecting with a vehicle battery, the output port of the external
power cable connects with the Power Port of the GPS to PC Data Cable.

WARNING – Use caution when connecting external power cable’s clip leads to a vehicle
battery. Do not allow any metal object to connect (short) the battery’s positive (+) terminal to
either the negative (-) terminal or the metal part of the vehicle battery. This could result in
high current, arcing, and high temperatures, exposing the user to possible injury.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 15

 Getting Started with
SG7

2.4 Inserting SIM Card

(a) Open the SIM card slot cover.

(b) Insert the SIM card with the contacts facing upward, as indicated by the SIM card icon next to
the SIM card slot.

(c) Close the cover to prevent water immersion.

(d) To eject the SIM card, slightly push it in to trigger the spring-loaded release mechanism

Insert the SIM card with the contacts facing upward, as indicated by the SIM card icon next to
the SIM card slot.

To eject the SIM card, slightly push it in to trigger the spring-loaded release mechanism.

Tip – The SIM card is provided by your cellular network service provider.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 16

 Getting Started with
SG7

2.5 Product Basic Supply Accessories

2.5.1 Base Kit Basic Supply

Item Picture

SG7 GNSS Receiver

UHF Whip Antenna (410-470 MHz)

Power Adapter

USB Type-C

H.I. Tape

Extension pole

Tribrach with optical plummet

Auxiliary H.I. Tool

Transport Hard Case

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 17

 Getting Started with
SG7

2.5.2 Rover Kit Basic Supply

Item Picture

SG7 GNSS Receiver

UHF Whip Antenna (410-470 MHz)

Power Adapter

USB Type-C

2M Range Pole w/bag

Auxiliary H.I. Tool

Transport Hard Case

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 18

 Getting Started with
SG7

2.6 Connecting to an Office Computer

The receiver can be connected to an office computer for serial data transfer or settings via a
FC2 USB Type-C. Before you connect to the office computer, ensure that the receiver is
powered on by internal battery or external power.

The following figure shows how to connect to the computer for serial data transfer or settings:

USB Type

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 19

 Getting Started with
SG7

2.7 Downloading Logged Data

Data logging involves the collection of GNSS measurement data over a period at a static point
or points, and subsequent post-processing of the information to accurately compute baseline
information.

2.7.1 FTP Download

The procedures of downloading logged data through FTP are as follows:

(1) Switch on the receiver, search its Wi-Fi in the computer and connect.
(2) After the successful connection, open the file manager in the computer and input
“ftp:\\192.168.1.1” in the address box.

(3) Input user name and password, the default user name and password are “ftp”.

(4) Double click the folder “repo_receiver SN” (take 3411955 as example), you will see 9
folders. The “push_log” folder is used to save the log files, and the other 8 folders represent
different logging sessions and are used for store static data.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 20

 Getting Started with
SG7

(5) Double click the folder that you have configured to store the static data, you will see the
folder(s) created by the SG7 system automatically and named by the date which is decide
by GPS time when you start to log data.

(6) Select the destination folder and double click it, two folders named as different data
format (hcn and rinex) will be displayed.

(7) Select the data format that you configured to save the static data, you will find the static
raw data.

Notes: For hcn files, the name of the file is represented as XXXXXXDDDNN, where XXXXXX is
the SN of the receiver, DDD is day of year, and NN is the recording session.

WARNING – The static data will be saved in the first logging session, the “record_1”
folder, by default. Old files will be deleted if the storage space is full. If you configure not to
auto delete old files when the memory is low, the receiver will stop data logging.

2.7.2 Web Server Download

The procedures of downloading logged data through web server refer to 5.4.4 Data
Download Submenu.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 21

 Getting Started with
SG7

2.7.3 USB Download

The procedures of downloading logged data in the receiver are as follows:

(1) Switch on the receiver and connect it with a computer by HCE600 Type-C. After the
successful connection, a removable disk named as the Serial Number (SN) of the receiver will
appear on the computer.

(2) Double click the removable disk and you will see the folder named as “repo”.

(3) Double click this folder, you will see 9 folders. The “push_log” folder is used to save the
log files, and the other 8 folders represent different logging session and are used for store
static data.

(4) Double click the folder that you have configured to store the static data, you will see the
folder(s) created by the SG7 system automatically and named by the date which is decide by
GPS time when you start to log data.

(5) Select the destination folder and double click it, and then two folders named as different
data format (hcn and rinex) will be displayed.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 22

 Getting Started with
SG7

(6) Select the data format that you have configured to save the static data, you will find the
static raw data.

Tip – For hcn files, the name of the file is represented as XXXXXXDDDNN, where XXXXXX is the
SN of the receiver, DDD is day of year, and NN is the recording session.

WARNING – The static data will be saved in the first logging session, the “record_1”
folder, by default. Old files will be deleted if the storage space is full. If you configure not to
auto delete old files when the memory is low, the receiver will stop data logging.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 23

 Front Panel Operation

3 Front Panel Operation

The front panel contains one LCD screen, two indicator LEDs, and two buttons. The operating
controls are all located on the front panel.

3.1 Main Operation Menus

The top-level menu of the front panel includes 6 parts: Info, SV, Mode, Power, Data and Set.
Info is the basic information of firmware such as SN, PN and etc. SV is the display of satellite
situation. Mode is the important part which illustrate the work mode and users can select the
mode according to their needs. Power shows the electric quantity of two batteries. Data is
used to set static mode and Set is to set the device according to personal habits including
language, brightness, etc.

The details of main operation are as follows and they are concluded two tables. The first table
includes 5 parts: Info, SV, Power, Data and Set and the second table displays details of Data.

Top-level Menu Second-level Menu Description

SN 3411956 Describe the main information of this
PN A19319430901060002 machine. SN displays the Serial Number
-015701 of the receiver. PN displays the Part
-020104 Number of the receiver. Version
Version 2.0.7 displays the firmware version. Register
Register 2030/12/31 displays the expiry date of registration
Info
Static off code. Static displays if the static is on or
Sample 5S not. Format displays the data type.
Format HCN Network displays the if a sim card
Diff Age 0.0S inserts the RTK. IMEI is International
Network No Sim Card Mobile Equipment Identity which is
IMEI 861529049455435 used to identify the RTK.

Indicate the total number of satellites

Total: 30/30
that have been tracked and the number
GPS: 10/10
of satellites tracked of each
SV BDS: 10/10
constellation, where BDS represents
GLO: 4/6
BeiDou, GLO represents GLONASS, and
GAL: 4/4
GAL represents Galileo.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 24

 Front Panel Operation

Indicates the remaining power of the

Power Power 95%
battery

Press Enter to select the brightness

Brightness High
including High, Medium and low.
Press Enter to select standby time
Standby Time 10s
including 5s, 10s, 30s, 1min, 30min
Press Enter to select sleep time
Sleep Time 1min
including 5s, 10s, 30s, 1min, 30min
WIFI ON Press Enter to turn on or turn off WIFI.
Press Enter to change the WIFI Mode
WIFI Mode AP including AP or STA. (The function is
Set unavailable when WIFI is off)
Press Enter to change the 4G status
4G SIM
including eSIM or SIM.
Channel Detection Only work on rover mode.
OEM Board Reset Press Enter to reset board.
Press Enter to change languages
Language English
(English or Chinese).
Voice Off Press Enter to turn on or turn off voice.
Back Press Enter to back to last page.
Base External UHF
Base Internal UHF
• Press Enter button to enter the
Base APIS
configuration screen of the selected
Base External UHF & APIS
Mode working mode.
Rover APIS
• More operation information, see 3.2
Rover UHF
Configure the Working Mode.
Rover NTRIP
Back

The details of Data operations are as follows:

Top-level Menu Second-level Menu Description

Press Enter button to switch static
Set on/off
measurement on or off.
Data Recording 00:00 Display the time of recording
Press Enter to change sample interval
Advanced Sample
(1s, 2s, 5s, 10s, 15s, 30s, 1m)

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 25

 Front Panel Operation

Elev Mask 10 Press Enter button to change the mask

degree degree from 0 degree to 90 degrees.
• Press Enter button to enter Duration
Time Setting screen.
• In the Duration Time Setting screen,
press Fn button to move to the
character of the duration time value
user want to make change, and then
press Enter button to change from 0 to
Duration
9. After the change has been done, user
1440min
can press Fn button to move to OK
field, and then Press Enter button to
save the change and back to the
second-level menu; or press Fn button
to move to Cancel field and press Enter
button to cancel the change and back
to the second-level menu.
Press Enter button and switch height
Measurement
between oblique, vertical, phase
phase Center
center.
Antenna
Press Enter button and input the
Height
measured antenna height.
0.0000m
Press Enter button and switch data
Format HCN format between Rinex2.11 and
Rinex3.02.
Ok Press Enter to complete settings.
Press Enter button to back to the
Cancel
last menu.
OK Press Enter to complete settings.
Press Enter button to back to the
Cancel
top-level menu.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 26

 Front Panel Operation

3.2 Configure the Working Mode

7 working modes are provided for quickly setting up an RTK base station or rover station. Users
can configure each working mode through the front panel as follows:

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 27

 Front Panel Operation

Top-level Menu Second-level Menu Description

Mode Base External UHF The title of this configuration
screen.
Press Enter to select correction
Format CMR format (RTD, CMR, RTCMv2.3,
RTCMv3 and RTCMv3.2).
Base External Press Enter button to save the
UHF settings and back to the top-level
OK
menu, and then this working mode
can take effect.
Press Enter button to cancel the
Cancel settings and back to the second-
level menu.
Mode Base External UHF The title of this configuration
screen.
Press Enter to select current
Protocol GEOMATE protocol (Transparent,
TT450s)
Press Enter to change the channel
Channel 1 456.0500
from 0 to 9
Press Enter to select Baud (4800,
Baud 9600
9600 and 19200)

Press Enter button to change the

Base Internal Power 1w
transmitting power (0.5w,1w,2w).
UHF
Press Enter to select correction
Format CMR format (RTD, CMR, RTCMv2.3,
RTCMv3 and RTCMv3.2).
Press Enter button to save the
settings and back to the top-level
OK
menu, and then this working mode
can take effect.
Press Enter button to cancel the
Cancel settings and back to the second-
level menu.

The title of this configuration

Base APIS Mode Base APIS
screen.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 28

 Front Panel Operation

Press Enter to select correction

Format CMR format (RTD, CMR, RTCMv2.3,
RTCMv3 and RTCMv3.2).
Press Enter to enter third-level menu
to select IP (211.144.120.97,
101.251.112.206) or press
IP 111.111.111.1
Customized IP to customize your own
IP

Press Enter button to change the port

Port 9901
from 9901 to 9920.
Press Enter button to save the
settings and back to the top-level
OK
menu, and then this working mode
can take effect.
Press Enter button to cancel the
Cancel settings and back to the second-level
menu.
Mode Base External UHF &
The title of this configuration screen.
APIS
Display the way of base station
Way External UHF+APIS
combination.
Press Enter to select correction
Format CMR format (RTD, CMR, RTCMv2.3,
RTCMv3 and RTCMv3.2).
Press Enter to enter third-level menu
to select IP (211.144.120.97,
101.251.112.206) or press
IP 111.111.111.1
Base External Customized IP to customize your own
UHF & APIS IP

Press Enter button to change the port

Port 9901
from 9901 to 9920.
Press Enter button to save the
settings and back to the top-level
OK
menu, and then this working mode
can take effect.
Press Enter button to cancel the
Cancel settings and back to the second-
level menu.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 29

 Front Panel Operation

The title of this configuration

Mode Rover APIS
screen.
Press Enter to enter third-level menu
Base ID 1234567
to change Base ID
Press Enter to enter third-level menu
to select IP (211.144.120.97,
101.251.112.206) or press
IP 210.14.66.58
Customized IP to customize your own
IP
Rover APIS
Press Enter button to change the port
Port 9902
from 9901 to 9920.
Press Enter button to save the settings
and back to the top-level menu, and
OK
then this working mode can take
effect.
Press Enter button to cancel the
Cancel settings and back to the second-
level menu.
The title of this configuration
Mode Rover UHF
screen.
Press Enter to select current
Protocol GEOMATE protocol (Transparent,
TT450s)
Press Enter to change the channel
Channel 1 456.0500
from 0 to 9
Press Enter to select Baud (4800,
Rover UHF Baud 9600
9600 and 19200)
Press Enter button to save the
settings and back to the top-level
OK
menu, and then this working mode
can take effect.
Press Enter button to cancel the
Cancel settings and back to the second-
level menu.
The title of this configuration
Mode Rover NTRIP
Rover NTRIP screen.
Status Not Login in in Indicates the login status.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 30

 Front Panel Operation

Press Enter button to save the

settings and back to the top-level
OK
menu, and then this working mode
can take effect.
Press Enter button to cancel the
Cancel settings and back to the second-
level menu.
Press Enter button to back to the top-
Back
level menu.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 31

 Equipment Setup and Operation

4 Equipment Setup and Operation

4.1 Post-processing Base Station Setup

For good performance, the following base station setup guidelines are recommended:

Components:

No. Name

a SG7 GNSS receiver

b Extension pole (30 cm)

c Tribrach adaptor

d Tribrach w/ Opti

e Aluminum tripod
Steps:

(1) Put tripod in the target position, center and level it roughly.
(2) Place and lock the tribrach in the tripod.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 32

 Equipment Setup and Operation

(3) Screw the receiver onto the tribrach.

(4) Center and level the receiver more precisely.
(5) Connect the receiver to external battery by using external power cable if necessary.
(6) Connect the receiver to external storage disk by using USB cable if necessary.
(7) Turn on the receiver by pressing the power button for 3 s.
(8) Measure the antenna height by using H.I. tape and auxiliary H.I. tool.
(9) Press the function button to select Data to start recording static raw.

If work with a data controller:

(10) Switch on the data controller and connect it to the receiver.

(11) Use software to configure the receiver as static mode.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 33

 Equipment Setup and Operation

4.2 Real-Time Base Station Setup

4.2.1 Internal Cellular or UHF

For good rover operation, the following base station setup guidelines are recommended:

Components:

a g

b
c

d e

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 34

 Equipment Setup and Operation

No. Name
a SG7 GNSS receiver
b UHF whip antenna
c Extension pole (30 cm)
d Tribrach adaptor
e Tribrach w/ Opti
f Aluminum tripod
g Micro SIM card (12 mm x 15 mm)

Steps:

(1) Put tripod in the target position, center and level it roughly.
(2) Place and lock the tribrach in the tripod.

If work as a cellular base station, the SIM card need to be inserted

(3) Screw the receiver onto the tribrach.

(4) Center and level the receiver more precisely.

If work as a UHF base station, the UHF whip antenna need to be connected to the receiver.

(5) Connect the receiver to external battery by using external power cable if necessary.
(6) Connect the receiver to external storage disk by using USB cable if necessary.
(7) Turn on the receiver by pressing the power button for 3 s.
(8) Measure the antenna height by using H.I. tape and auxiliary H.I. tool.
(9) Switch on the data controller and connect it to the receiver.
(10)Use software to configure the receiver as cellular base or UHF base mode.

4.2.2 External UHF

For good performance, the following base station setup guidelines are recommended:

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 35

 Equipment Setup and Operation

Components:

a
h
b

c
d

j
e
k

No. Name
a SG7 GNSS receiver
b Extension pole (30 cm)
c Tribrach adaptor
d Tribrach w/ Opti
e GPS to datalink cable (power cable)
f Aluminum tripod
h Whip antenna
i 3 m cable for datalink antenna 3m
j Pole mounting
k External 410-470 datalink

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 36

 Equipment Setup and Operation

Steps:

(1) Put tripod in the target position, center and level it roughly.
(2) Place and lock the tribrach in the tripod.
(3) Screw the receiver onto the tribrach.
(4) Center and level the receiver more precisely.
(5) Connect the receiver to external datalink by using GPS to datalink cable.
(6) Hang the external datalink on the tripod leg.
(7) Connect the receiver to external battery by using external power cable if necessary.
(8) Connect the receiver to external storage disk by using USB cable if necessary.
(9) Turn on the receiver by pressing the power button for 3 s.
(10)Measure the antenna height by using H.I. tape and auxiliary H.I. tool.
(11)Turn on the external datalink and configure it as need.

If work with a data controller:

(12)Switch on the data controller and connect it to the receiver.

(13)Use software to configure the receiver as cellular base or UHF base mode.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 37

 Equipment Setup and Operation

4.3 Real-Time Rover Station Setup

For good performance, the following rover station setup guidelines are recommended:

Components:

a
d

b
c

No. Name
a SG7 GNSS receiver
b whip antenna
c 2M range pole w/bag
d Micro SIM card (12 mm x 15 mm)

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 38

 Equipment Setup and Operation

Steps:

(1) Keep the receiver fully charged.

If work as a cellular rover station, the SIM card need to be inserted before the batteries.

(2) Screw the receiver onto the pole.

If work as a UHF rover station, the UHF whip antenna need to be connected to the receiver.

(3) Turn on the receiver by pressing the power button for 3 s.

(4) Switch on the data controller and connect it to the receiver.
(5) Use software to configure the receiver as cellular rover or UHF rover mode.
(6) Center and level the receiver more precisely.
(7) Use software to start survey.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 39

 Equipment Setup and Operation

4.4 Notes of using tilt measurement

1. At the beginning of initialization, the pole height of the instrument should be the same as
that antenna height in the software.

2. In the process of tilt measurement, if the controller shows that “Tilt is not available, please
measure in alignment” (red), please shake RTK slightly from left to right or back to front until
the reminder disappears.

3. The controller will prompt “Tilt is not available, please measure in alignment” when the
receiver is stationary over 30 seconds or the pole hit the ground toughly.

4. The pole cannot be shaken when point is collected.

5. Initialization is required:
▪ when the RTK is turned on every time;
▪ when IMU module is turned on every time;
▪ when receiver drops at working;
▪ when the pole is tilted more than 65 degree;
▪ when the receiver is stationary more than 10 minutes;
▪ when the RTK rotates too fast on the matching pole (2 rounds per second);
▪ when the pole hit the ground toughly.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 40

 Equipment Setup and Operation

5 Configuring Through a Web Browser

Supported browsers:

 Google Chrome
 Microsoft Internet Explorer○R version 10, or higher

To connect to the receiver through a web browser:

1. Turn on the Wi-Fi of the receiver.

2. Search the wireless network named as GNSS-XXXXXXX (the SN of your receiver) on your
computer, and then establish the connection.
3. After the successful connection between your computer and the receiver, enter the IP
address (192.168.1.1) of the receiver into the address bar of the web browser on your
computer:

4. The web browser prompts you to enter a login account and password:

The default login account for the receiver is:

➢ Login Account: admin

➢ Password: password

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 41

 Equipment Setup and Operation

Note – Tick remember me option, and then the browser will remember the Login Account and
Password you entered.

5. Once you log in, the web page appears as follows:

This web page shows the configuration menus on the left of the browser window, and the setting on
the right. Each configuration menu contains the related submenus to configure the receiver and
monitor receiver performance.

This chapter describes each configuration menu.

To view the web page in another language, select the corresponding language name from the dropdown
list on the upper right corner of the web page.

Currently, two languages are available:

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 42

 Equipment Setup and Operation

5.1 Status Menu

This menu provides a quick link to review the receiver's position information, satellites tracked, runtime,
current data log status, current outputs, available memory, and more.

5.1.1 Position Submenu

This page shows the relevant position information about the receiver's position solution which
including the position, DOP values, satellites used and tracked, and the receiver clock
information.

5.1.2 Activity Submenu

Lists several important items to help you understand how the receiver is being used and its
current operating condition. Items include the identities of currently tracked satellites, internal
and external storage usage rate, how long the receiver has been operational, state of the
internal battery, power source state, files being logged, and data streams being output. With
this information, it is easy to tell exactly what functions the receiver is performing

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 43

 Equipment Setup and Operation

5.1.3 Google Map Submenu

Tap this submenu to show the location of the receiver on Google map.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 44

 Equipment Setup and Operation

5.2 Satellites Menu

Use the Satellites menu to view satellite tracking details and enable/disable GPS, GLONASS,
BDS and Galileo constellations. These menus include tabular and graphical displays to provide
all required information on satellite tracking status.

5.2.1 Tracking Table Submenu

Provides the status of satellites tracked in general, such as the satellite ID, satellite type,
attitude angle, azimuth angle, L1 SNR, L2 SNR, L5 SNR and enable/disable status of each one.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 45

 Equipment Setup and Operation

5.2.2 Tracking Info. Table Submenu

The following figure is an example of satellite track diagram page. Users can determine the
satellite types and the corresponding SNR of L-band carriers to be displayed in any
combination.

5.2.3 Tracking Skyplot Submenu

The following figure is an example of Skyplot page.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 46

 Equipment Setup and Operation

5.2.4 Satellite Activation Submenu

Use this menu to enable or disable satellites.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 47

 Equipment Setup and Operation

5.3 Receiver Configuration Menu

Use this menu to configure settings such as the antenna type and height, elevation mask and
PDOP setting, the reference station coordinates, receiver resetting and web interface language:

5.3.1 Description

This submenu shows the receiver information and reference station

information, including antenna related information, elevation mask angle,
reference station work mode and position, etc.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 48

 Equipment Setup and Operation

5.3.2 Antenna Configuration Submenu

Use the antenna configuration menu to configure all the items related to
the GNSS antenna. You must enter the correct values for all antenna-
related fields, because the choices you make affect the accuracy for logged
data and broadcast correction data significantly:

5.3.3 Reference Station Settings Submenu

Use this screen to configure settings such as the station coordinates and
the broadcast station identifiers. You must enter accurate information in
these fields, as this data affects the accuracy of logged data files and
broadcast correction data significantly:

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 49

 Equipment Setup and Operation

For Reference Station Mode, there are three modes available:

a) Auto Rover: The receiver will serve as a rover after this mode is enabled, and then
receive correction data through the working mode set last time.

b) Auto Base: The receiver will serve as a base after this mode is enabled, and then
broadcast correction data based on coordinate inputted by user or obtained through
autonomous positioning automatically.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 50

 Equipment Setup and Operation

c) Manual Base: The receiver will serve neither as a base nor a rover after this mode is
enabled. Users need to configure the receiver manually

For Reference Latitude and Reference Longitude:

There are mainly three methods to enter the reference coordinates and shown as follows:

a) Acquire Current Position: Click this button to acquire current position obtained through
autonomous positioning automatically.
b) Manual Input: Manually input the coordinate of a control point.
c) From CORS: After the receiver logging in CORS, the software can record the coordinate of current
position based on fix solution.

For Sample for Average:

Users can determine the positioning limit and sampling amount. The positioning limit falls into two types:

a) Single Solution Coordinates: Collect the coordinates of receiver obtained through autonomous
positioning.
b) Fixed Solution Coordinates: Only collect coordinates of receiver with a fixed solution.

After the configuration of positioning limit and sampling amount, click to carry out sampling and
averaging → the progress bar will show the progress → the result will be served as the coordinate of
current position.

If users need to save the changes, please tap button.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 51
 Equipment Setup and Operation

5.3.4 Receiver Reset Submenu

Use this screen to completely or partially reset the receiver:

5.3.5 Languages Submenu

Use this screen to select the web interface language:

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 52

 Equipment Setup and Operation

5.3.6 User Management Submenu

5.3.7 HCPPP Settings

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 53

 Equipment Setup and Operation

5.4 Data Recording Menu

Use the Data Logging menu to set up the receiver to log static GNSS data
and to view the logging settings. You can configure settings such as
observable rate, recording rate, continuous logging limit, and whether to
auto delete old files when memory is low. This menu also provides the
controls for the FTP push feature:

5.4.1 Log Settings Submenu

Here shows the data logging status, including internal and external storage usage and data
logging status of each session. Also, users can configure the data logging settings for each
session, including recording name, store location, storage limit, store formats, start time, etc

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 54

 Equipment Setup and Operation

To edit the settings of each session, click the Modify button to the right of the
required session, and then the Recording Edit screen appears:

Click advanced to see more settings.

In this screen, you can configure all the data logging parameters, and determine whether
the recording files will be affected by the FTP Push. The parameters are mainly as follows:

➢ Auto Record: on or off.

➢ Sample Interval: Select the observable rate from the dropdown list.
➢ Elevation Mask: Enter the elevation mask.
➢ Duration Time: Set the duration of data logging.
GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 55
 Equipment Setup and Operation

➢ Site Name: Enter the name of the site.

➢ Antenna Height: the measured height value.
➢ Measure way: Antenna Phase Center, Vertical Height, Slant Height
➢ Storage Format: Select the format of the data store.
➢ RINEX Version: OFF, 3.02, 2.11
➢ Start Date: Select Yes or No option to determine whether to auto record start date.
➢ Apply Time: Select Yes or No option to determine whether to auto record apply
time.
➢ Integral Point Store: Select Yes or No option to determine whether to allow
receiver to save data every hour.
➢ Circulating Memory: Select Yes or No option to determine whether to auto delete old
files if the storage space is full.
➢ Repeat Observations: Select Yes or No option to determine whether to turn on to
record a single observation.
➢ Store Location: Internal Storage, External Storage.
➢ Assigned Storage: The assigned memory size of current thread(for example, Record
1) is 10000MB
➢ Observer: Enter the name of observer.
➢ Observer Agency: Enter the name of observer agency.
➢ FTP Push: Decide whether to push the stored files to the FTP server of your choice.

Tap button to save the settings and back to the Log Settings screen.
Also, users can click to abandon the changed settings and back to
Log Settings screen.

Note – To modify data logging parameters, make sure the data logging sessio
n is switched off.

To switch on or off ANY data logging session, tap the ON or OFF button on
the right of the required session.

To delete the recorded files of ANY data logging session, tap the Clear button
on the right of the required session.

To delete the recorded files of ALL data logging sessions, tap the Clear ALL
Accounts button.

5.4.2 FTP Push Settings Submenu

Use this screen to configure the receiver to push stored files to the FTP
server of your choice. Only files that are configured to use FTP push are
transmitted.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 56

 Equipment Setup and Operation

Tap Modify button on the right of the required FTP server and the FTP Push
Settings screen appears:

5.4.3 FTP Push Log Submenu

Shows the related information about the recorded filed that be pushed. And users can tap
Clear Ftp Send Log button in the upper right corner to clear the log of FTP Push operations.
GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 57
 Equipment Setup and Operation

5.4.4 Data Download Submenu

In this submenu, users can download the data files that recorded in the internal storage
through the internal FTP site.

1. Click this submenu, and then the log on dialogue box will prompt you to enter a user
name and password:

The default logon account for the internal FTP site is:
➢ User name: ftp
➢ Password: ftp
2. Click the directory named as “repo” to view and download the files currently stored
on the receiver:

3. To find the file need to be downloaded, click the name of data logging session → the

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 58

 Equipment Setup and Operation

date of file that be recorded → the format of the file → the name of the target file.

4. To download a file, left click the name of the target file → download the file according
to the prompts.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 59

 Equipment Setup and Operation

5.5 IO Settings Menu

Use the IO Settings menu to set up all receiver outputs and inputs. The receiver can output
CMR, RTCM, Raw data, Ephemeris data, GPGGA, GPGSV, on TCP/IP, UDP, serial port, or
Bluetooth ports.

5.5.1 IO Settings Submenu

The following figure shows an example of the screen that appears when you select this
submenu.

In this submenu, users can configure 6 types of input and output settings.

1. RTK Client

After configuring the settings of RTK client, users can log on CORS or APIS. Tap the Connect
button to the right → the IO Settings screen will appear → choose one of the connection
protocols among the NTRIP, APIS_BASE and APIS_ROVER → configure the related parameters
→ click to log on CORS or APIS.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 60

 Equipment Setup and Operation

➢ Connection Protocol: NTRIP

➢ Connection Protocol: APIS_BASE

➢ Connection Protocol: APIS_ROVER

➢ Connection Protocol: TCP

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 61

 Equipment Setup and Operation

2. TCP/UDP_Client/NTRIP Server

Tap the Connect button on the right of required TCP/UDP Client → the IO Settings screen will
appear → select the connection protocol from TCP, UDP,NTRIP1.0 and NTRIP2.0 → enter the
IP and Port of the target server → configure messages that you want to output to the target
server → click to save and complete the connection.

➢ Connection Protocol: TCP

➢ Connection Protocol: UDP

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 62

 Equipment Setup and Operation

➢ Connection Protocol: NTRIP1.0

➢ Connection Protocol: NTRIP2.0

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 63

 Equipment Setup and Operation

3. TCP Server/NTRIP Caster

Tap the Connect button to the right of required TCP Server/NTRIP Caster→ the IO Settings
screen will appear → select one of the connection protocols between NTRIP and TCP →
configure the other related parameters → click to save the settings and open the
server.

➢ Connection Protocol: TCP

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 64

 Equipment Setup and Operation

➢ Connection Protocol: NTRIP

4. Serial Port

Tap the Settings button on the right of Serial Port → the Serial Port Setup screen will appear
→ select Baud Rate used to transmit data → configure the messages that you want to output
through the serial port → click to save the settings and start to transmit.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 65

 Equipment Setup and Operation

5. Bluetooth

Tap the Settings button to the right of Bluetooth → the Bluetooth Set screen will appear →
configure the messages that you want to transmit through Bluetooth → click to
save the settings and start to transmit.

6. Radio

Tap the Settings button to the right of Radio → the Radio Settings screen will appear → select
the format of differential data that you want to transmit through radio from the dropdown list

→ click to save the settings and start to transmit.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 66

 Equipment Setup and Operation

5.6 Network Setting Menu

Use this menu to view network information, configure the receiver’s mobile network, set email
alert for specific situation, configure HTTP or HTTPS port, and the username and password of
internal FTP site:

5.6.1 Description Submenu

Use this submenu to check the information of network setting.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 67

 Equipment Setup and Operation

5.6.2 Mobile Network Setting Submenu

Use this submenu to configure GPRS model, network module and modify dialing status.

5.6.3 Email Alarm Submenu

Use this submenu to choose which situation of receiver will be alerted and input the email
address.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 68

 Equipment Setup and Operation

5.6.4 HTTP Submenu

Use this submenu to configure HTTP port.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 69

 Equipment Setup and Operation

5.6.5 HTTPS Submenu

Use this submenu to configure HTTPS port.

5.6.6 FTP Service Submenu

Use this submenu to configure the user name and password of internal FTP site.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 70

 Equipment Setup and Operation

5.7 Module Setting Menu

Use this menu to check module information, configure WiFi, bluetooth, radio related settings,
and turn on/off static voice of buzzer:

5.7.1 Description Submenu

Use this submenu to check the information of WiFi module, bluetooth module and radio
module.

5.7.2 WiFi Submenu

Use this submenu to turn on/off WiFi function and modify password.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 71

 Equipment Setup and Operation

5.7.3 Bluetooth Settings Submenu

Use this submenu to turn on/off bluetooth function and modify PIN number.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 72

 Equipment Setup and Operation

5.7.4 Radio Settings Submenu

Use this submenu to turn on/off radio function and configure radio parameters.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 73

 Equipment Setup and Operation

5.8 Firmware Menu

Use this menu to check the current firmware information, download the system log, update
the receiver firmware, download or update the configuration file and register the receiver, and
more:

5.8.1 Firmware Info Submenu

Use this submenu to check the current firmware information. The following figure shows an
example of the firmware information.

5.8.2 Hardware Version Submenu

Use this submenu to check the hardware information, including main board version and core
board version:

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 74

 Equipment Setup and Operation

5.8.3 Config File Submenu

Use this submenu to update Configuration File.

5.8.4 System Log Download Submenu

Use this submenu to download the system log of the receiver.

5.8.5 User Log Submenu

Use this submenu to download the user log. Tap Download to download current user log; Tick
items that you want to see on the user log and tap confirm button to confirm selected user
log.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 75

 Equipment Setup and Operation

5.8.6 Firmware Update Submenu

Use this submenu to load new firmware to the receiver across the network. Tap the Browse
button to locate the upgrade file → tap Confirm button to confirm the selected upgrading file
and start upgrading.

Notes

 It may take about 3 or 4 minutes to complete the firmware upgrading. Do not touch
the power button or unplug the power until the upgrading process finishes, or damage
will be caused to the receiver.

 The receiver will restart after the firmware upgrading is done, so users need to
reconnect the receiver with your co mputer v ia Wi -Fi, and then log-in the receiver
through a web browser to continue the configuration.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 76

 Equipment Setup and Operation

5.8.7 GNSS Board Upgrade Submenu

Use this submenu to upgrade GNSS Board. Use this submenu to load new board to the receiver
across the network. Tap the Browse button to locate the upgrade file → tap Confirm button
to confirm the selected upgrading file and start upgrading.

5.8.8 Radio Upgrade Submenu

Use this submenu to browse upgrade file and upgrade radio. Use this submenu to load new
radio to the receiver across the network. Tap the Browse button to locate the upgrade file →
tap Confirm button to confirm the selected upgrading file and start upgrading.

5.8.9 Upgrade Online Submenu

Use this submenu to input Server Address and upgrade online.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 77

 Equipment Setup and Operation

5.8.10 GNSS Registration Submenu

Use this submenu to register the receiver. Paste or enter the registration code to the
Registration Code field → tap Registration button to complete the registration.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 78

 Equipment Setup and Operation

5.9 Cloud Service Setting Menu

5.9.1 Cloud Service Setting Submenu

Use this submenu to turn on or turn off Cloud Service, Auto Start, Remote Control and
configure other settings.

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 79

 Communication Ports Definition

A Communication Ports Definition

AI GEOMATE SG7 Receiver IO Port (7-pin Lemo Port)

Definition

PIN FUNCTION

1 Ground ( - )

2 Ground ( - )

3 RS232-TX (Output)

4 PPS

5 Not Used

6 VIN

7 RS232-RX (Input)

GEOMATE SG7 GNSS USER GUIDE | 2022-04 P a g e | 80

1) FCC 15.19
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

2）FCC 15.21
Warning: Changes or modifications to this unit not expressly approved by the part responsible for
compliance could void the user’s authority to operate the equipment.

3) FCC 15.105
For a Class B digital device or peripheral, the instructions furnished the user shall include the
following or similar statement, placed in a prominent location in the text of the manual:

Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.

4）FCC RF Exposure- portable

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
This equipment should be installed and operated with minimum distance 50cm between the radiator
& your body.