Chapter 6

Bandwidth Utilization:
Multiplexing and
Spreading
Kyung Hee
University
1
 Presentation / Lecture Acknowledgement

Professor Choong Seon Hong, Ph.D.

Networking Lab,
Kyung Hee University, Republic of Korea.

Kyung Hee
University
2
 Bandwidth Utilization

Note

Bandwidth utilization is the wise use of

available bandwidth to achieve
specific goals.

Efficiency can be achieved by multiplexing;

privacy and anti-jamming can be achieved
by spreading.

Kyung Hee
University
3
6.1 MULTIPLEXING
Whenever the bandwidth of a medium linking two
devices is greater than the bandwidth needs of the
devices, the link can be shared. Multiplexing is the
set of techniques that allows the simultaneous
transmission of multiple signals across a single
data link. As data and telecommunications use
increases, so does traffic.
Topics discussed in this section:
Frequency-Division Multiplexing
Wavelength-Division Multiplexing
Synchronous Time-Division Multiplexing
Statistical Time-Division Multiplexing
Kyung Hee
University
4
 Multiplexing
 Dividing a link into channels

 Word link refers to the physical path

 Channel refers to the portion of a link that carries a transmission
between a given pair of lines.
Kyung Hee
University
5
 Multiplexing
 Multiplexing
is the set of techniques that allows the simultaneous
transmission of multiple signals across a single data link.

Kyung Hee
University
6
 FDM
 Multiplexer
Transmission streams combine into a single stream (many to
one)

 Demultiplexer
Stream separates into its component transmission (one to
many) and directs them to their intended receiving devices

Kyung Hee
University
7
 FDM
 FDM (Frequency-Division)

FDM is an analog multiplexing technique

that combines analog signals.
Kyung Hee
University
8
 FDM (cont’d)
 FDM process
Each telephone generates a signal of a similar frequency range
These signals are modulated onto different carrier frequencies
(f1, f2, f3)

Kyung Hee
University
9
 FDM(cont’d)
 FDM multiplexing process, frequency-domain

00 4 20 24
0

0 4 24 28
20 32

0 4 28 32

Kyung Hee
University
10
 FDM (cont’d)
 FDM multiplexing process, time-domain

Kyung Hee
University
11
 FDM(cont’d)
 Demultiplexing
Separates the individual signals from their carries and passes them to
the waiting receivers.

Kyung Hee
University
12
 FDM(cont’d)
 FDM demultiplexing, frequency-domain

20

20 24 0 4
24

24 28 0 4
20 32
28

28 32 0 4

Kyung Hee
University
13
 FDM(cont’d)
 FDM demultiplexing process, time-domain

Kyung Hee
University
14
 Example 6.1

Assume that a voice channel occupies a bandwidth of 4 kHz.

We need to combine three voice channels into a link with a
bandwidth of 12 kHz, from 20 to 32 kHz. Show the
configuration, using the frequency domain. Assume there
are no guard bands.
Solution
We shift (modulate) each of the three voice channels to a
different bandwidth, as shown in Figure 6.6. We use the 20-
to 24-kHz bandwidth for the first channel, the 24- to 28-kHz
bandwidth for the second channel, and the 28- to 32-kHz
bandwidth for the third one. Then we combine them as
shown in Figure 6.6.
Kyung Hee
University
15
 FDM(cont’d)
Figure 6.6 Example 6.1

Kyung Hee
University
16
 Example 6.2

Five channels, each with a 100-kHz bandwidth, are to be

multiplexed together. What is the minimum bandwidth of
the link if there is a need for a guard band of 10 kHz
between the channels to prevent interference?

Solution
For five channels, we need at least four guard bands. This
means that the required bandwidth is at least
5 × 100 + 4 × 10 = 540 kHz,
as shown in Figure 6.7.

Kyung Hee
University
17
 FDM(cont’d)

Figure 6.7 Example 6.2

Kyung Hee
University
18
 FDM(cont’d)
 Example : Cable Television
Coaxial cable has a bandwidth of approximately 500Mhz
Individual television channel requires about 6Mhz of bandwidth
for transmission
Can carry 83 channels theoretically

Kyung Hee
University
19
 Analog Hierarchy

To maximize the efficiency of their infrastructure, telephone companies have traditionally

multiplexed signals from lower bandwidth lines onto higher bandwidth lines.
Kyung Hee
University
20
 Example 6.4

The Advanced Mobile Phone System (AMPS) uses two

bands. The first band of 824 to 849 MHz is used for
sending, and 869 to 894 MHz is used for receiving. Each
user has a bandwidth of 30 kHz in each direction. How
many people can use their cellular phones simultaneously?

Solution
Each band is 25 MHz. If we divide 25 MHz by 30 kHz, we
get 833.33. In reality, the band is divided into 832 channels.
Of these, 42 channels are used for control, which means only
790 channels are available for cellular phone users.
Kyung Hee
University
21
 Wavelength Division Multiplexing (WDM)
 WDM is conceptually same as FDM
Except that the multiplexing and demultiplexing involve light
signals transmitted through fiber-optic channels

Kyung Hee
University
22
 WDM (cont’d)

WDM is an analog multiplexing

technique to combine optical signals.

λ1 λ1

λ2 λ2
λ1 + λ2 + λ3
λ3 λ3

Very narrow bands of light from different sources are combined to make
a wider band of light

Kyung Hee
University
23
 WDM (cont’d)
 Combining and splitting of light sources are easily handled by a
prism
Prism bends a beam of light based on the angle of incidence and the
frequency.

Kyung Hee
University
24
 TDM

TDM (Time-Division Multiplexing)

is a digital process that can be applied when the
data rate capacity of the transmission medium is
greater than the data rate required by the sending
and receiving device

TDM is a digital multiplexing technique

for combining several low-rate
channels into one high-rate one.

Kyung Hee
University
25
 TDM(cont’d)
 Time-Division Multiplexing
 is a digital process that allows several connections to share
the high bandwidth of a link, time is shared.
 Two different schemes : Synchronous TDM & Statistical TDM

Kyung Hee
University
26
 TDM(cont’d)

Figure 6.13 Synchronous time-division multiplexing

UNIT UNIT
Time slot(T/3 sec)

In Synchronous TDM, the data rate of the link is n times

faster, and the unit duration is n times shorter.
Kyung Hee
University
27
 Example 6.5

In Figure 6.13, the data rate for each input connection is 1

kbps. If 1 bit at a time is multiplexed (a unit is 1 bit), what is
the duration of (a) each input slot, (b) each output slot, and
(c) each frame?

Solution
We can answer the questions as follows:
a. The data rate of each input connection is 1 kbps. This
means that the bit duration is 1/1000 s or 1 ms. The
duration of the input time slot is 1 ms (same as bit
duration).
Kyung Hee
University
28
 Example 6.5 (continued)

b. The duration of each output time slot is one-third of the

input time slot. This means that the duration of the
output time slot is 1/3 ms.

c. Each frame carries three output time slots. So the

duration of a frame is 3 × 1/3 ms, or 1 ms. The duration
of a frame is the same as the duration of an input unit.

Kyung Hee
University
29
 Synchronous TDM (cont’d)
 Interleaving
Synchronous TDM can be compared to a very fast
rotating switch
Switches are synchronized and rotate at the same
speed, but in opposite directions.
On the multiplexing side, as the switch opens in
front of a connection, that connection has the
opportunity to send a unit onto the path.
This process is called INTERLEAVING.
On the demultiplexing side, as the switch opens in
front of a connection, that has the opportunity to
receive a unit from the path.
Kyung Hee
University
30
 Synchronous TDM (cont’d)

□ Empty Slots
 If a source does not have data to send, the corresponding slot
in the output frame is empty.

Kyung Hee
University
31
 Synchronous TDM - Data rate Management
 How to handle a disparity in the data rates with TDM.
If data rates are not the same, 3 strategies can be used.
 Multi-level multiplexing
 Multiple-Slot Allocation
 Pulse Stuffing

Kyung Hee
University
32
 Synchronous TDM - Multilevel multiplexing
 Multilevel multiplexing is a technique used when the data rate of an input
line is a multiple of others.
For example, the first two 20khz input lines can be multiplexed together to
provide a data rate equal to the last three.
A second level of multiplexing can create an output of 160 kbps.

Kyung Hee
University
33
 Synchronous TDM - Multiple-Slot Allocation
 Sometime it is more efficient to allot more than one slot in a frame
to a single input line.
For example, the input line with a 50-kbps data rate can be given two
slots in the output.
We insert a serial-to-parallel converter in the line to make two inputs
out of one.

Kyung Hee
University
34
 Synchronous TDM - Pulse Stuffing
 Sometime the bit rates of sources are not multiple integers of each other.

 Pulse stuffing is to make the highest input data rate the dominant data
rate and then add dummy bits to the input lines with lower rates.

 This technique is called Pulse stuffing, bit padding, or bit stuffing.

Kyung Hee
University
35
 Digital Signal Service
 DS(Digital Signal) Service
- Digital Hierarchy

advantage
- less sensitive than analog service to noise
- lower cost
Kyung Hee
University
36
 Statistical TDM

 In statistical TDM, slots are dynamically allocated

to improve bandwidth efficiency.

 In a synchronous TDM, some slots are empty

because the corresponding line does not have data

to send.

 In statistical TDM, no slot is left empty as long as

there are data to be sent by any input line.

Kyung Hee
University
37
 Statistical TDM

Figure 6.26 TDM slot comparison

Kyung Hee
University
38
 Statistical TDM

 Addressing

A slot needs to carry data as well as the address

of the destination.

n-bits define N different output lines

 n = log2 N

 No synchronization bit

 The frame in the statistical TDM need not be

synchronized, so we do not need synchronization
bits.
Kyung Hee
University
39
6.2 SPREAD SPECTRUM

In spread spectrum (SS), we combine signals from different

sources to fit into a larger bandwidth, but our goals are to
prevent eavesdropping and jamming. To achieve these
goals, spread spectrum techniques add redundancy.

Topics discussed in this section:

Frequency Hopping Spread Spectrum (FHSS)
Direct Sequence Spread Spectrum Synchronous (DSSS)

Kyung Hee
University
40
 Spread Spectrum
Figure 6.27 Spread spectrum
 Spread Spectrum achieves through two principles.

 The bandwidth allocated to each station needs to be larger

than what is needed.

 The spreading process occurs after the signal is created

by the source.

Kyung Hee
University
41
 Spread Spectrum
Figure 6.28 Frequency hopping spread spectrum (FHSS)
 FHSS uses M different carrier frequencies that are modulated by the
source signal.

 At one moment, the signal modulates one carrier frequency;

 At the next moment, the signal modulates another carrier frequency.

Kyung Hee
University
42
 Spread Spectrum

Figure 6.29 Frequency selection in FHSS

Kyung Hee
University
43
 Spread Spectrum

Figure 6.30 FHSS cycles

Kyung Hee
University
44
 Spread Spectrum

Figure 6.31 Bandwidth sharing

 If the number of hopping frequencies is M, we can multiplex

M channels into one by using the same Bss bandwidth.

Kyung Hee
University
45
 Spread Spectrum
Figure 6.32 DSSS

 In DSSS, we replace each data bit with n bits using a spreading code.

 Each bit is assigned a code of n bits, called chips, where the chip rate is n
times that of the data bit.

Kyung Hee
University
46
 Spread Spectrum

Figure 6.33 DSSS example

Kyung Hee
University
47
 Q&A

Kyung Hee
University
48