REVISION HISTORY PART LIST

REV DATE BY DESCRIPTION CKD ITEM P/N DESCRIPTION TOTAL UNIT MATERIAL
0 15/09/2023 IS INITIAL RELEASE IS 7 1 1302491 Steel Grating 1 Each DMC-001
1 26/09/2023 JT CHANGE PRODUCT CODE AND PART UPDATE JT 2 1302483 Plate - Short 1 Each DMC-001
3 1302487 Plate - Short with Fork Holes 1 Each DMC-001
2 14/11/2023 IS ADDITIONAL PLAQUE UPDATE IS
4 1302482 Plate - Long 2 Each DMC-001
5 1302489 Plate - Forktine 2 Each DMC-001
6 1302490 Plate - Tare Pocket 2 Each DMC-001
1 7 1302484 Plate - Middle Member 5 Each DMC-001
8 1302486 Plate - Hidden Gusset 4 Each DMC-001
9 1302488 Plate - Fork Gusset 4 Each DMC-001
10 1302485 Plate - Fork Support 4 Each DMC-001
1 11 1302493 Plate - Lug Side 4 Each DMC-001
12 1302494 Plate - Lug Middle 4 Each DMC-001
13 DCL-082 Empty Lift Only Plaque 1 Each DMC-001
D C 14 2T Load Ring Lugs 8 Each Standard

D ( 1 : 10 )
BREAK OUT VIEW

12

A 4

13 2300

3 6

B(1:8)
9
14

11

5
282

2
10
746
8 A(1:8) C(1:8) 808
BREAK OUT VIEW 3500

SURFACE FINISH
THIRD ANGLE PRODUCT CODE :
PREPARATION Abrasive Blasting Class 2.5
PRIMER Hot-dip Galvanized 75μm minimum thickness 13-PMGG3500/2320/8T
COATING Outdoor Paint YELLOW RAL1023 75μm minimum thickness DESCRIPTION :
PROJECTION
FINISHING Gloss Finish with No Runs 26 Activity Street PO Box 2039 Ph 1300 662 987 8T Steel Pallet
SCALE: N.T.S.
POST COATING Paint Lugs BLUE RAL5002 and Attach Decals TOLERANCES: (mm)
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
1302481 ASSEMBLY
NOTE: X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH.
X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
1. FOR GENERAL TOLERANCING REFER TO TOLERANCE TABLE IN THE TITLE BLOCK X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.

ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. N/A 845.763 kg 1 of 4 2
 6 U U x2 x10
(4) 4
N
2300 6 x2
K (4) 80-315

1915

x2 4
K 4 80-315 x2
K ( 1 : 15 ) 4
1455.3 J-J ( 1 : 15 )
L L
(1300)
1090.3
x4 8 x4
4 4
H
844.7

H (74) Hidden Gusset

479.7
x4
6
J J
T T
x4
6 x4
6 4
0 F ( 1 : 10 )
G ( 1 : 10 )
Inside Fork Gusset View
G G
3500
x2
x10 4
4
NO MESH VIEW
x2
11 4 (4)
x10
4
x4
6
12 4
10 x10
4

6 L-L ( 1 : 12 )
x2
6
N ( 1 : 10 )
E-E ( 1 : 8 )
P-P ( 1 : 10 ) R-R ( 1 : 10 )
x4 x2
(6) 4

250
P F R
E E x4
6
x10
x10 (4)
(4)
4
P R
2
x2
0 745 1381 2469 2780 3500 4
x4
(6)
T-T ( 1 : 12 ) x10
4
NOTES:
1. FOR GENERAL TOLERANCING REFER TO TOLERANCE TABLE IN THE TITLE BLOCK U(1:8)
2. ALL WELDS TO BE FULL PERIMETER 6mm FILLETS OR EQUIVALENT DTT. EXCEPT WHERE STATED OTHERWISE. NO LUG VIEW H-H ( 1 : 8 )
3. WELDING TO BE IN ACCORDANCE WITH AS/NZS1554.1:2014 SP.
4. ALL WELD TO HAVE MINIMUM YIELD STRENGTH OF 430MPa
THIRD ANGLE PRODUCT CODE :
5. IF WELDING STANDARD AS/NZS 1554.1 IS UNAVAILABLE, THE LATEST VERSION OF ISO 3834.3 | CATEGORY B IS TO BE
REFERENCED FOR THE CORRESPONDING WELDING SPECIFICATIONS. 13-PMGG3500/2320/8T
6. VISUAL APPEARANCE OF THE WELDING IS TO BE OF A CONSISTENT STANDARD. DESCRIPTION :
PROJECTION
7. IN ADDITION TO THE REQUIREMENTS OF AS/NZS 1554.1, ALL WELDS ARE TO COMPLY WITH THE FOLLOWING VISUAL 26 Activity Street PO Box 2039 Ph 1300 662 987 8T Steel Pallet
SCALE: N.T.S.
APPEARANCE AND FINISHING STANDARDS: TOLERANCES: (mm)
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
a. NO VISIBLE CRACKS d. NO SHARP NOTCHING ON UNDERCUT X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
1302481 ASSEMBLY
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH.
b. NO UNCONSUMED WIRE e. REMOVE ALL SPATTER X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
c. NO SURFACE POROSITY X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.
845.763 kg
ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. N/A 2 of 4 2
 WELD EVERY ADJACENT
4 50 BEARING BAR - TYP.

AB
W(1:5)

AB
W

WELD EVERY ADJACENT

4 50 BEARING BAR - TYP.

x2
4 100-438

x4
4
V
Y
WELD FILLET
CORNERS ONLY 2

5
x2 x8
4 100-422 6
15
V(1:5)
x4
4
Y(1:8)
NOTES:
AB ( 1 : 12 )
1. FOR GENERAL TOLERANCING REFER TO TOLERANCE TABLE IN THE TITLE BLOCK
2. ALL WELDS TO BE FULL PERIMETER 6mm FILLETS OR EQUIVALENT DTT. EXCEPT WHERE STATED OTHERWISE.
3. WELDING TO BE IN ACCORDANCE WITH AS/NZS1554.1:2014 SP.
4. ALL WELD TO HAVE MINIMUM YIELD STRENGTH OF 430MPa
THIRD ANGLE PRODUCT CODE :
5. IF WELDING STANDARD AS/NZS 1554.1 IS UNAVAILABLE, THE LATEST VERSION OF ISO 3834.3 | CATEGORY B IS TO BE
REFERENCED FOR THE CORRESPONDING WELDING SPECIFICATIONS. 13-PMGG3500/2320/8T
6. VISUAL APPEARANCE OF THE WELDING IS TO BE OF A CONSISTENT STANDARD. DESCRIPTION :
PROJECTION
7. IN ADDITION TO THE REQUIREMENTS OF AS/NZS 1554.1, ALL WELDS ARE TO COMPLY WITH THE FOLLOWING VISUAL 26 Activity Street PO Box 2039 Ph 1300 662 987 8T Steel Pallet
SCALE: N.T.S.
APPEARANCE AND FINISHING STANDARDS: MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
TOLERANCES: (mm)
a. NO VISIBLE CRACKS d. NO SHARP NOTCHING ON UNDERCUT X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
1302481 ASSEMBLY
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH.
b. NO UNCONSUMED WIRE e. REMOVE ALL SPATTER X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
c. NO SURFACE POROSITY X.XXX = ± 0.005
ANGLE = ± 0.25º
EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
N/A 845.763 kg 3 of 4 2
DEPARTMENT.
 PART LIST
ITEM P/N DESCRIPTION TOTAL UNIT
1 DCL-047 Vehicle Lash Point 8 Each
2 DCL-048 Daywalk 2 Each
3 DCL-058 LASHING POINT 8 Each
4 DCL-083 Daywalk Plaque 2 Each
2 5 DCL-088 WLL 8T 2 Each

3 3 4 3 3

AA

5 1 1 2 1 1

3 3 4 3 3

5 1 AA ( 1 : 18 ) 1 2 1 1

THIRD ANGLE PRODUCT CODE :

13-PMGG3500/2320/8T
DESCRIPTION :
PROJECTION
26 Activity Street PO Box 2039 Ph 1300 662 987 8T Steel Pallet
SCALE: N.T.S.
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
TOLERANCES: (mm)
X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH. 1302481 ASSEMBLY
X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.

ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. N/A 846.042 kg 4 of 4 2
 REVISION HISTORY
REV DATE BY DESCRIPTION CKD
0 15/09/2023 IS INITIAL RELEASE IS
1 19/10/2023 IS LOAD BAR UPDATE DIMENSION IS

2290

30

25 `2
CROSS BAR
Ø6mm 94
A

B 136 `1
32 `0.5

0 96.3 1243.8 2323.8 3373.8 3470

39 `2 93 `1

1 LOAD BAR
32 x 3.75 +0.5
-0.0 mm A ( 1 : 10 )
136 `1
THIRD ANGLE PRODUCT CODE :

DESCRIPTION :
98 `1 PROJECTION
26 Activity Street PO Box 2039 Ph 1300 662 987 Steel Grating
SCALE: N.T.S.
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
TOLERANCES: (mm)
B ( 1 : 10 ) X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH. 1302491 PART
NOTE: X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
1. FOR GENERAL TOLERANCING REFER TO TOLERANCE TABLE IN THE TITLE BLOCK X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.

ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. DMC-001 240.649 kg 1 of 1 1
 REVISION HISTORY
REV DATE BY DESCRIPTION CKD
0 15/09/2023 IS INITIAL RELEASE IS

UP 90° R6
409.1
324.4

A
84.8
0
UP 90° R6
2167 (6)

2300

35

R6

90
R6
90

250

A(1:5) R6
PRODUCT CODE :
2x THRU HOLE THIRD ANGLE

DESCRIPTION :
PROJECTION
NOTE: 26 Activity Street PO Box 2039 Ph 1300 662 987 Plate - Short
SCALE: N.T.S.
1. FOR GENERAL TOLERANCING REFER TO TOLERANCE TABLE IN THE TITLE BLOCK MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
TOLERANCES: (mm)
2. ACTUAL PLATE/SHEET SIZE SHALL MEET THE REQUIREMENTS OF AS1365 X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
1302483 PART
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH.
TOLERANCE GUIDE X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
X.XXX = ± 0.005
3. REFER DXF FOR THE PROFILE ANGLE = ± 0.25º
EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. DMC-001 44.150 kg 1 of 1 0
 REVISION HISTORY
REV DATE BY DESCRIPTION CKD
0 15/09/2023 IS INITIAL RELEASE IS

UP 90° R6
B
409.1

324.4

A
84.8 177.6 204.6

0
(6)
UP 90° R6 1050

2167

2300

+1
R6 - 0 +1
R6 R6 - 0

+2
90 150 - 0
90 R6

R6

35
250
+2
250 - 0
A(1:5)
B(1:8)
2x THRU HOLE
2x THRU HOLE
THIRD ANGLE PRODUCT CODE :

DESCRIPTION :
PROJECTION
NOTE: 26 Activity Street PO Box 2039 Ph 1300 662 987 Plate - Short with Fork Holes
SCALE: N.T.S.
1. FOR GENERAL TOLERANCING REFER TO TOLERANCE TABLE IN THE TITLE BLOCK TOLERANCES: (mm)
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
2. ACTUAL PLATE/SHEET SIZE SHALL MEET THE REQUIREMENTS OF AS1365 X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
1302487 PART
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH.
TOLERANCE GUIDE X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
3. REFER DXF FOR THE PROFILE X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DMC-001 40.619 kg 1 of 1 0
ANGLE = ± 0.25º DEPARTMENT.
 REVISION HISTORY
REV DATE BY DESCRIPTION CKD 85
0 15/09/2023 IS INITIAL RELEASE IS 150 150
1 14/11/2023 IS ADDED PLAQUE HOLES IS

60

8x n5 THRU

C(1:8) 8 X 45°
C 1 CHAM +
238 - 0
A 2
UP 90° R6
B
409.1
324.4
180.6
409.1
84.8
0
(6)
UP 90° R6 (85.6)
8 X 45°
1088 CHAM

3320

3488
Bend Line Location +1
1 -0

+1
+1 R8 - 0
R8 - 0
6
90
+2
150 - 0 R6

250
B(1:1)
+2
350 - 0
THIRD ANGLE PRODUCT CODE :

A ( 1 : 11 )
2x THRU HOLE DESCRIPTION :
PROJECTION
NOTE: 26 Activity Street PO Box 2039 Ph 1300 662 987 Plate - Long
SCALE: N.T.S.
1. FOR GENERAL TOLERANCING REFER TO TOLERANCE TABLE IN THE TITLE BLOCK TOLERANCES: (mm)
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
2. ACTUAL PLATE/SHEET SIZE SHALL MEET THE REQUIREMENTS OF AS1365 X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
1302482 PART
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH.
TOLERANCE GUIDE X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
3. REFER DXF FOR THE PROFILE X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.
61.081 kg
ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. DMC-001 1 of 1 1
 REVISION HISTORY
REV DATE BY DESCRIPTION CKD
0 15/09/2023 IS INITIAL RELEASE IS

DOWN 90° R4 20 X 45°

334 CHAM

636.1

489.6

146.5

DOWN 90° R4
(4)

0 500 750 1550 1800 2300

150 R4

350

THIRD ANGLE PRODUCT CODE :

DESCRIPTION :
PROJECTION
NOTE: 26 Activity Street PO Box 2039 Ph 1300 662 987 Plate - Forktine
SCALE: N.T.S.
1. FOR GENERAL TOLERANCING REFER TO TOLERANCE TABLE IN THE TITLE BLOCK MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
TOLERANCES: (mm)
2. ACTUAL PLATE/SHEET SIZE SHALL MEET THE REQUIREMENTS OF AS1365 X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
1302489 PART
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH.
TOLERANCE GUIDE X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
X.XXX = ± 0.005
3. REFER DXF FOR THE PROFILE ANGLE = ± 0.25º
EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. DMC-001 41.213 kg 1 of 1 0
 REVISION HISTORY
REV DATE BY DESCRIPTION CKD
0 15/09/2023 IS INITIAL RELEASE IS

99.9
437.8

DOWN 90° R2
340.9

238

DOWN 90° R2
97

0 (4)
(99.9)

Bend Line Location

100 R2

250
THIRD ANGLE PRODUCT CODE :

DESCRIPTION :
PROJECTION
NOTE: 26 Activity Street PO Box 2039 Ph 1300 662 987 Plate - Tare Pocket
SCALE: N.T.S.
1. FOR GENERAL TOLERANCING REFER TO TOLERANCE TABLE IN THE TITLE BLOCK TOLERANCES: (mm)
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
2. ACTUAL PLATE/SHEET SIZE SHALL MEET THE REQUIREMENTS OF AS1365 X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
1302490 PART
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH.
TOLERANCE GUIDE X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
3. REFER DXF FOR THE PROFILE X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.
14.283 kg
ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. DMC-001 1 of 1 0
 REVISION HISTORY
REV DATE BY DESCRIPTION CKD
0 15/09/2023 IS INITIAL RELEASE IS

Bend Line Location

DOWN 45° R4
+0 DOWN 45° R4
433.2 - 1
A

390

350 DOWN 90° R4

289.6
0
DOWN 90° R4 B 140
1088
(4)
3320

3488
95

10 X 45°
+
12 X 45°
CHAM 76 - 0 +1
R8 - 0 +1 +0
2 R8 - 0 74 - 1
CHAM
(70)
2
+2 45°
150 - 0
250

2
+
238 - 0
2 +2
8 X 45° 350 - 0
CHAM (49)
B(1:9)
2x THRU HOLE 50

THIRD ANGLE PRODUCT CODE :

84
A(1:9) DESCRIPTION :
PROJECTION
NOTE: 26 Activity Street PO Box 2039 Ph 1300 662 987 Plate - Middle Member
SCALE: N.T.S.
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected]
1. FOR GENERAL TOLERANCING REFER TO TOLERANCE TABLE IN THE TITLE BLOCK TOLERANCES: (mm) PART NO / DWG NO : DRAWING TYPE:
X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
2. ACTUAL PLATE/SHEET SIZE SHALL MEET THE REQUIREMENTS OF AS1365 X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH. 1302484 PART
TOLERANCE GUIDE X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.
3. REFER DXF FOR THE PROFILE ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. DMC-001 43.628 kg 1 of 1 0
 REVISION HISTORY
REV DATE BY DESCRIPTION CKD
0 15/09/2023 IS INITIAL RELEASE IS

THRU HOLE
6 X 45°
+ CHAM
R8 - 1
0 +1
R8 - 0

28
+
238 - 0
2
+2
150 - 0

6 X 45°
+ CHAM
350 - 2
0
(10)

420

THIRD ANGLE PRODUCT CODE :

DESCRIPTION :
PROJECTION
NOTE: 26 Activity Street PO Box 2039 Ph 1300 662 987 Plate - Hidden Gusset
SCALE: N.T.S.
1. FOR GENERAL TOLERANCING REFER TO TOLERANCE TABLE IN THE TITLE BLOCK TOLERANCES: (mm)
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
2. ACTUAL PLATE/SHEET SIZE SHALL MEET THE REQUIREMENTS OF AS1365 X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
1302486 PART
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH.
TOLERANCE GUIDE X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
3. REFER DXF FOR THE PROFILE X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.
3.609 kg
ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. DMC-001 1 of 1 0
 REVISION HISTORY
REV DATE BY DESCRIPTION CKD
0 15/09/2023 IS INITIAL RELEASE IS

THRU HOLE

+1
15 X 45° R8 - 0
CHAM

DOWN 60° R6 DOWN 60° R6

(143)

+
238 - 0
2
+2
150 - 0

95

15 X 45°
CHAM +2 (6)
350 - 0

445.2

600.4

72.3 R6
120°
120°

530

THIRD ANGLE PRODUCT CODE :

DESCRIPTION :
PROJECTION
NOTE: 26 Activity Street PO Box 2039 Ph 1300 662 987 Plate - Fork Gusset
SCALE: N.T.S.
1. FOR GENERAL TOLERANCING REFER TO TOLERANCE TABLE IN THE TITLE BLOCK TOLERANCES: (mm)
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
2. ACTUAL PLATE/SHEET SIZE SHALL MEET THE REQUIREMENTS OF AS1365 X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
1302488 PART
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH.
TOLERANCE GUIDE X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
3. REFER DXF FOR THE PROFILE X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.
4.246 kg
ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. DMC-001 1 of 1 0
 REVISION HISTORY
REV DATE BY DESCRIPTION CKD
0 15/09/2023 IS INITIAL RELEASE IS

96

342 (4)

THIRD ANGLE PRODUCT CODE :

DESCRIPTION :
PROJECTION
NOTE: 26 Activity Street PO Box 2039 Ph 1300 662 987 Plate - Fork Support
SCALE: N.T.S.
1. FOR GENERAL TOLERANCING REFER TO TOLERANCE TABLE IN THE TITLE BLOCK MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
TOLERANCES: (mm)
2. ACTUAL PLATE/SHEET SIZE SHALL MEET THE REQUIREMENTS OF AS1365 X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH. 1302485 PART
TOLERANCE GUIDE X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
3. REFER DXF FOR THE PROFILE X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.

ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. DMC-001 1.031 kg 1 of 1 0
 REVISION HISTORY
REV DATE BY DESCRIPTION CKD
0 15/09/2023 IS INITIAL RELEASE IS

43
8 X 45°
CHAM

(74)

+
238 - 0
2 90

R6

(74)

14 X 45° (25)
CHAM
78

THIRD ANGLE PRODUCT CODE :

DESCRIPTION :
PROJECTION
NOTE: 26 Activity Street PO Box 2039 Ph 1300 662 987 Plate - Lug Side
SCALE: N.T.S.
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected]
1. FOR GENERAL TOLERANCING REFER TO TOLERANCE TABLE IN THE TITLE BLOCK TOLERANCES: (mm) PART NO / DWG NO : DRAWING TYPE:
X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
2. ACTUAL PLATE/SHEET SIZE SHALL MEET THE REQUIREMENTS OF AS1365 X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH. 1302493 PART
TOLERANCE GUIDE X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.
3. REFER DXF FOR THE PROFILE ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. DMC-001 2.956 kg 1 of 1 0
 REVISION HISTORY
REV DATE BY DESCRIPTION CKD
0 15/09/2023 IS INITIAL RELEASE IS

14 X 45°
43 CHAM

(74)

+
238 - 0
2 90

R6

(74)

78 (25)

THIRD ANGLE PRODUCT CODE :

DESCRIPTION :
PROJECTION
NOTE: 26 Activity Street PO Box 2039 Ph 1300 662 987 Plate - Lug Middle
SCALE: N.T.S.
1. FOR GENERAL TOLERANCING REFER TO TOLERANCE TABLE IN THE TITLE BLOCK TOLERANCES: (mm)
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
2. ACTUAL PLATE/SHEET SIZE SHALL MEET THE REQUIREMENTS OF AS1365 X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
1302494 PART
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH.
TOLERANCE GUIDE X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
3. REFER DXF FOR THE PROFILE X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DMC-001 2.990 kg 1 of 1 0
ANGLE = ± 0.25º DEPARTMENT.
 REVISION HISTORY
REV DATE BY DESCRIPTION CKD
0 21/07/2023 JT INITIAL RELEASE JT
1 17/08/2023 JT INCREASE TEXT SPACING JT
2 26/09/2023 JT CHANGE "TARE" TO EMPTY JT

200

(3)
182

FONT STYLE: ROBOTO

FONT SIZE: 23mm
THRU LASER CUT 63 100

1 R10

83.1

THIRD ANGLE PRODUCT CODE :

DESCRIPTION :
PROJECTION
NOTE: 26 Activity Street PO Box 2039 Ph 1300 662 987 Empty Lift Only Plaque
SCALE: N.T.S.
1. FOR GENERAL TOLERANCING REFER TO TOLERANCE TABLE IN THE TITLE BLOCK TOLERANCES: (mm)
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
2. ACTUAL PLATE/SHEET SIZE SHALL MEET THE REQUIREMENTS OF AS1365 X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
DCL-082 PART
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH.
TOLERANCE GUIDE X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
3. REFER DXF FOR THE PROFILE X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.
0.428 kg
ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. DMC-001 1 of 1 2
 REQ'D REQ'D
ITEM UNIT #: UNIT #: UNIT #: UNIT #: UNIT #: REMARKS
QTY THICKNESS
ACHIEVE ACHIEVE WELD QUALITY ACHIEVE ACHIEVE WELD QUALITY ACHIEVE ACHIEVE WELD QUALITY ACHIEVE ACHIEVE WELD QUALITY ACHIEVE ACHIEVE WELD QUALITY
QTY THICKNESS (FAIR / POOR) QTY THICKNESS (FAIR / POOR) QTY THICKNESS (FAIR / POOR) QTY THICKNESS (FAIR / POOR) QTY THICKNESS (FAIR / POOR)

1 1 3.75 mm [ ] [ ] [ ] [ ] [ ]
2 1 6 mm [ ] [ ] [ ] [ ] [ ]
3 1 6 mm [ ] [ ] [ ] [ ] [ ]
4 2 6 mm [ ] [ ] [ ] [ ] [ ]
5 2 4 mm [ ] [ ] [ ] [ ] [ ]
6 2 4 mm [ ] [ ] [ ] [ ] [ ]
7 5 4 mm [ ] [ ] [ ] [ ] [ ]
8 4 10 mm [ ] [ ] [ ] [ ] [ ]
9 4 6 mm [ ] [ ] [ ] [ ] [ ]
10 4 4 mm [ ] [ ] [ ] [ ] [ ]
11 4 25 mm [ ] [ ] [ ] [ ] [ ]
12 4 25 mm [ ] [ ] [ ] [ ] [ ]
13 1 3 mm [ ] [ ] [ ] [ ] [ ]
14 8 [ ] [ ] [ ] [ ] [ ]

Inspector
(Signature):

1st Inspection (Part 1):

1 14 7
Parts Check and Weld Quality
PART LIST
REQ'D
ITEM P/N DESCRIPTION TOTAL
THICKNESS
11 1 1302491 Steel Grating 1 3.75 mm
2 1302483 Plate - Short 1 6 mm
3 1302487 Plate - Short with Fork Holes 1 6 mm
D B 4 1302482 Plate - Long 2 6 mm
5 1302489 Plate - Forktine 2 4 mm
6 1302490 Plate - Tare Pocket 2 4 mm
7 1302484 Plate - Middle Member 5 4 mm
2 8 1302486 Plate - Hidden Gusset 4 10 mm
9 1302488 Plate - Fork Gusset 4 6 mm
12 D ( 1 : 10 ) 10 1302485 Plate - Fork Support 4 4 mm
B(1:8) 11 1302493 Plate - Lug Side 4 25 mm
BREAK OUT VIEW
12 1302494 Plate - Lug Middle 4 25 mm
C 13 DCL-082 Empty Lift Only Plaque 1 3 mm
9 14 2T Load Ring Lugs 8
A 4

13

3 5

10
C(1:8)
8 THIRD ANGLE PRODUCT CODE :

A ( 1 : 10 ) 13-PMGG3500/2320/8T
PO NUMBER BREAK OUT VIEW DESCRIPTION :
PROJECTION
NAME 8T Steel Pallet
SCALE: N.T.S. 26 Activity Street PO Box 2039 Ph 1300 662 987
REVISION HISTORY MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO :
TOLERANCES: (mm) DRAWING TYPE:
SIGNATURE REV DATE BY DESCRIPTION CKD ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
X=±1
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH. 1302481 CDR
DATE 0 23/11/2023 JT INITIAL RELEASE JT X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.

1 15/01/2024 JT ADDED CRITICAL DIMENSIONS FOR MESH JT ANGLE = ± 0.25º

THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. N/A N/A 1 of 9 1
PO NUMBER NAME: DATE:

Balloon: Req'd Value Achieve Dimension Achieve Dimension Achieve Dimension Achieve Dimension Achieve Dimension Remarks

Unit #: Unit #: Unit #: Unit #: Unit #:

A 3470 mm

B 32mm ±0.5

C 2290 mm

D 3.75 mm +0.5

F 6 mm

G 30 mm

H 136mm ±1

J 93mm ±1

K 98mm ±1

Inspector
(Signature):

1st Inspection (Part 2): 30 G

Critical Dimensions B
& A
Assembly Fitment
CROSS BAR
3470 32 `0.5
F Ø6mm

136 `1 H

+0.5 93 `1 J
D 3.75 - 0

AD ( 1 : 6 )

2290 C

AD
98 `1 K

AE ( 1 : 6 )

THIRD ANGLE PRODUCT CODE :

13-PMGG3500/2320/8T
DESCRIPTION :
AE PROJECTION
26 Activity Street PO Box 2039 Ph 1300 662 987 8T Steel Pallet
SCALE: N.T.S.
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
TOLERANCES: (mm)
X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH. 1302481 CDR
X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.

ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. N/A N/A 2 of 9 1
PO NUMBER NAME: DATE:

Balloon: Req'd Value Achieve Dimension Achieve Dimension Achieve Dimension Achieve Dimension Achieve Dimension Remarks

Unit #: Unit #: Unit #: Unit #: Unit #:

A 808 mm

B 2300 mm

C 5 mm

D 15 mm

F 282 mm

G 746 mm

H 3500 mm

J 1530 mm

K 800 mm

Inspector
(Signature):

H
282 F

746 G
J 3500 H

A 808

B 2300

H ( 1 : 22 )

1530 800 K

15 D
5 C

THIRD ANGLE PRODUCT CODE :

13-PMGG3500/2320/8T
J(1:3)
DESCRIPTION :
PROJECTION
K(1:3) SCALE: N.T.S. 26 Activity Street PO Box 2039 Ph 1300 662 987 8T Steel Pallet
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
TOLERANCES: (mm)
X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH. 1302481 CDR
X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.

ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. N/A N/A 3 of 9 1
PO NUMBER NAME: DATE:

Balloon: Req'd Value Achieve Dimension Achieve Dimension Achieve Dimension Achieve Dimension Achieve Dimension Remarks

Unit #: Unit #: Unit #: Unit #: Unit #:

A OK

B OK

C OK

D OK

F OK

G OK

H OK

J OK

K OK

L OK

Inspector
(Signature):

1st Inspection (Part 3): SL3 ML3 ML4 SL4

Critical Weld
W1 = 4x
6 NDT REQ'D

SIDE LUG WELDS

POSITION W1 NDT PASSED/FAILED

A SL1

B SL2

C SL3

D SL4
L-L ( 1 : 5 )

MIDDLE LUG WELDS

W2 = 4x POSITION W2 W3 NDT PASSED/FAILED
6 NDT REQ'D
F ML1

W3 = 4x G ML2
6 NDT REQ'D

M L H ML3

M-M ( 1 : 5 ) J ML4

SL1 M L SL2
ML1 ML2 THIRD ANGLE PRODUCT CODE :

13-PMGG3500/2320/8T
K
DESCRIPTION :
ALL WELDS ARE FULL PERIMETER 6mm FILLETS OR PROJECTION
26 Activity Street PO Box 2039 Ph 1300 662 987 8T Steel Pallet
EQUIVALENT DTT. EXCEPT WHERE STATED OTHERWISE. SCALE: N.T.S.
VISUAL APPEARANCE OF THE WELDING IS TO BE OF A
L TOLERANCES: (mm)
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
NDT WELDS: X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
CONSISTENT STANDARD. X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH. 1302481 CDR
100% ON LUGS X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.

ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. N/A N/A 4 of 9 1
PO NUMBER NAME: DATE:

Balloon: Req'd Value Achieve Dimension Achieve Dimension Achieve Dimension Achieve Dimension Achieve Dimension Remarks

Unit #: Unit #: Unit #: Unit #: Unit #:

A OK

B OK

C OK

D OK

F OK

G OK

H OK

J OK

K OK

L OK

Inspector
(Signature):

LRL5 LRL6 LRL7 LRL8

W4 = 8x
6 NDT REQ'D LOAD RING LUG WELDS
POSITION W4 W5 NDT PASSED/FAILED

A LRL1

B LRL2

C LRL3

W5 = 8x D LRL4
6 NDT REQ'D

N(1:5) F LRL5

G LRL6

H LRL7

N
LRL1 LRL2 LRL3 LRL4 J LRL8

THIRD ANGLE PRODUCT CODE :

K 13-PMGG3500/2320/8T
DESCRIPTION :
ALL WELDS ARE FULL PERIMETER 6mm FILLETS OR PROJECTION
26 Activity Street PO Box 2039 Ph 1300 662 987 8T Steel Pallet
EQUIVALENT DTT. EXCEPT WHERE STATED OTHERWISE. SCALE: N.T.S.
VISUAL APPEARANCE OF THE WELDING IS TO BE OF A
L TOLERANCES: (mm)
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
NDT WELDS: X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
CONSISTENT STANDARD. 100% ON LUGS X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH. 1302481 CDR
X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.

ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. N/A N/A 5 of 9 1
PO NUMBER NAME: DATE:

Balloon: Req'd Value Achieve Dimension Achieve Dimension Achieve Dimension Achieve Dimension Achieve Dimension Remarks

Unit #: Unit #: Unit #: Unit #: Unit #:

A OK

B OK

C OK

D OK

F OK

G OK

H OK

J OK

Inspector
(Signature):

A
4x
4 NDT REQ'D

4x
R 6 NDT REQ'D

C
4x D
4 NDT REQ'D

P ( 1 : 10 ) 2x
(4) NDT REQ'D

R ( 1 : 10 )

NDT WELDS: P
5% ON GENERAL
G
4
x4 F
NDT WELDS:
100% ON FORKTINE
H PRODUCT CODE :
THIRD ANGLE
13-PMGG3500/2320/8T
DESCRIPTION :
ALL WELDS ARE FULL PERIMETER 6mm FILLETS OR PROJECTION
26 Activity Street PO Box 2039 Ph 1300 662 987 8T Steel Pallet
EQUIVALENT DTT. EXCEPT WHERE STATED OTHERWISE. SCALE: N.T.S.
VISUAL APPEARANCE OF THE WELDING IS TO BE OF A
J TOLERANCES: (mm)
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
CONSISTENT STANDARD. X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH. 1302481 CDR
X.XX = ± 0.05 ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.

ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. N/A N/A 6 of 9 1
PO NUMBER NAME: DATE:

Balloon: Req'd Value Achieve Dimension Achieve Dimension Achieve Dimension Achieve Dimension Achieve Dimension Remarks

Unit #: Unit #: Unit #: Unit #: Unit #:

A OK

B OK

C OK

D OK

F OK

G OK

H OK

J OK

K OK

L OK

Inspector
(Signature):

WELD EVERY ADJACENT

4 50 BEARING BAR - TYP.

WELD EVERY ADJACENT

4 50 BEARING BAR - TYP.

x4
4
U ( 1 : 10 )
NO POROSITY PRESENT D

NO ROCKING MOVEMENT F

CHAMFER ALL SHARP EDGES G

U
REMOVE ALL BURRS AND SLAG H

NO WELD SPATTER AND WELD WIRE J

THIRD ANGLE PRODUCT CODE :
NO OIL CONTAMINATION BEFORE BLASTING K
13-PMGG3500/2320/8T
DESCRIPTION :
ALL WELDS ARE FULL PERIMETER 6mm FILLETS OR PROJECTION
8T Steel Pallet
SCALE: N.T.S. 26 Activity Street PO Box 2039 Ph 1300 662 987
EQUIVALENT DTT. EXCEPT WHERE STATED OTHERWISE. MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO :
VISUAL APPEARANCE OF THE WELDING IS TO BE OF A
L TOLERANCES: (mm) DRAWING TYPE:
X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
1302481 CDR
CONSISTENT STANDARD. X.X = ± 0.5
X.XX = ± 0.05
WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH.
ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.

ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. N/A N/A 7 of 9 1
PO NUMBER NAME: DATE:

Balloon: Req'd Value Achieve Dimension Achieve Dimension Achieve Dimension Achieve Dimension Achieve Dimension Remarks

Unit #: Unit #: Unit #: Unit #: Unit #:

A OK

B OK

C OK

D OK

F OK

Inspector
(Signature):

2nd Inspection (Part 1):

Accessories & Coating Y

8T STEEL PALLET
A PAINTED YELLOW RAL1023
o
4x MIDDLE LUG
PAINTED BLUE RAL5002 B
o

V(1:5)

4x SIDE LUG AND OUTSIDE FRAME LUG SIDE

PAINTED BLUE RAL5002 C
o

V 8x LOAD RING LUG AND WHOLE CAVITY

PAINTED BLUE RAL5002 D
o
W

W(1:5)

THIRD ANGLE PRODUCT CODE :

13-PMGG3500/2320/8T
DESCRIPTION :
PROJECTION
26 Activity Street PO Box 2039 Ph 1300 662 987 8T Steel Pallet
SCALE: N.T.S.
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
TOLERANCES: (mm)
X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
Y(1:5) X.X = ± 0.5 WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH. 1302481 CDR
NO FLAKING COATING F X.XX = ± 0.05
X.XXX = ± 0.005
ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH
EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.
MATERIAL : WEIGHT: SHEET NO: REV:

ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. N/A N/A 8 of 9 1
PO NUMBER NAME: DATE:

Balloon: Req'd Value Achieve Dimension Achieve Dimension Achieve Dimension Achieve Dimension Achieve Dimension Remarks

Unit #: Unit #: Unit #: Unit #: Unit #:

A 8PCS

B 2PCS

C 8PCS

D 2PCS

F 2PCS

G OK

H OK

Inspector
(Signature):

2nd Inspection (Part 3): PART LIST

Decals & Pre-Shipment
ITEM P/N DESCRIPTION TOTAL

A 1 DCL-047 Vehicle Lash Point 8

B 2 DCL-048 Daywalk 2

C 3 DCL-058 LASHING POINT 8

5 DCL-088 WLL 8T 2
D
4 DCL-083 Daywalk Plaque 2
3 3 4 3 3 F

AA

5 1 1 2 1 1

3 3 4 3 3

AA ( 1 : 18 )
5 1 1 2 1 1

THIRD ANGLE PRODUCT CODE :

G PLAQUE RIVETED 13-PMGG3500/2320/8T

DESCRIPTION :
PROJECTION
26 Activity Street PO Box 2039 Ph 1300 662 987 8T Steel Pallet
VERIFY PLAQUE SCALE: N.T.S.
MARYBOROUGH QLD 4650 MARYBOROUGH QLD 4650 [email protected] PART NO / DWG NO : DRAWING TYPE:
H INFORMATION TOLERANCES: (mm)
X=±1 ALL PARTS TO BE FREE FROM SPATTER, SHARP EDGES AND OTHER IMPERFECTIONS
1302481 CDR
o X.X = ± 0.5
X.XX = ± 0.05
WHICH MAY AFFECT THE FUNCTION, FIT OR FINISH.
ALL INFORMATION AND DETAILS CONTAINED IN THIS DRAWING ARE PROTECTED BY COPYRIGHT LAWS AND CANNOT TO BE REPRODUCED OR SHARED WITH MATERIAL : WEIGHT: SHEET NO: REV:
X.XXX = ± 0.005 EXTERNAL PARTIES WITHOUT THE WRITTEN PERMISSION OF THE OMNI-TUFF GROUP PTY LTD TRADING AS DAYWALK.

ANGLE = ± 0.25º
THIS DRAWING MAY BE SUBJECT TO THE ADJUSTMENT OF DIMENSIONS, MATERIALS, AND ANY OTHER SPECIFICATION AS DIRECTED BY OUR ENGINEERING
DEPARTMENT. N/A N/A 9 of 9 1