Scribd
Upload
6 views

CCNA2_lab_2_2_1_en

This document outlines the procedure for configuring a router using the System Configuration dialog. It includes steps for entering setup mode, configuring global parameters, and interface parameters, as well as instructions for viewing and managing the configuration. The lab emphasizes that the configuration will not be saved and provides guidance on using default settings and entering specific parameters during the setup process.

Uploaded by

daotuyensp1
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
6 views

CCNA2_lab_2_2_1_en

This document outlines the procedure for configuring a router using the System Configuration dialog. It includes steps for entering setup mode, configuring global parameters, and interface parameters, as well as instructions for viewing and managing the configuration. The lab emphasizes that the configuration will not be saved and provides guidance on using default settings and entering specific parameters during the setup process.

Uploaded by

daotuyensp1
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Lab 2.2.

1 Router Configuration Using Setup

Objective

• Use the System Configuration dialog (setup).


• Establish some basic router configurations.

Background/Preparation
A new router will not find its configuration file when started and should automatically enter the setup
dialog. If the router has already been configured the setup command may be used at the command
line while in privileged mode. The setup dialog prompts for basic setup options, such as which
protocols will be used and the IP address and subnet mask for each interface the router has. The
setup dialog provides default values for most of the configurable options. The user can either accept
these or enter their own. If setup does not provide a prompted entry for specific interface information,
it will have to be entered manually at a later time. (With this lab, the setup utility will be run but the
configuration will not be saved.)
This lab assumes that the HyperTerminal console session to the router has already been established
by the instructor. The following resources will be required:
• PC with HyperTerminal configured
• Console or rollover cable and DB-9 to RJ-45 adapter
• Router

Step 1 Start the router and begin setup mode


Option 1
If the router was just started and the configuration file was missing, setup mode will be entered
automatically with no passwords required. This is what would happen with a new router.

1-3 CCNA 2: Routers and Routing Basics v 3.1 - Lab 2.2.1 Copyright  2003, Cisco Systems, Inc.
Option 2
If the router was previously configured and it is desired to see and change existing settings, it will be
necessary to login and provide a password of cisco. Type enable at the command prompt to enter
privileged mode and enter the password class. Enter setup at the router prompt to start the system
configuration dialog.
Option 3
If the router was previously configured, it is possible to simulate a new router by removing the
configuration file from NVRAM using the erase startup-config command in privileged mode.
Use the reload command to restart the router and enter setup mode.
Note: The order of the messages displayed during Setup may vary depending on the Cisco IOS
software release and feature set on the router. Therefore the following prompts may not exactly
reflect the messages on the screen.

Step 2 Continue with the setup dialog


a. The router prompts, "Continue with configuration dialog?“ Enter yes to continue with the setup
dialog.
b. The router prompts afterwards, "Would you like to enter basic management setup?" Enter no to
continue.
c. What is the importance of words in the square brackets? ___________________________

Step 3 Show the current interface summary


a. The router asks, “First, would you like to see the current interface summary?” or "Would you like
to enter basic management setup?" Press the Enter key or type yes to accept the default
answers.
b. Fill in the following table with the information displayed.

Interface IP-Address OK Method Status Protocol

Step 4 Configure global parameters


a. Configure the router using the default settings for any questions the router asks if it has already
been configured. The router may be named at this time if it has not been already. Make sure that
cisco is entered as the enable secret password. Next, the basic management setup prompt will
appear. This allows parameters such as router name, privileged level passwords, and virtual
terminal password to be entered. Answer the prompts as follows: Router name = Central,
enable secret password = cisco, enable password = class, virtual password = cisco.
b. Next will be the prompt to enter various parameters including SNMP settings, and routed and
routing protocol settings. Answer no to these prompts, except for the "Configure IP?" prompt.

Step 5 Configure interface parameters


a. From this point on, the prompts vary depending on the available router interfaces. Complete the
setup steps as appropriate.

2-3 CCNA 2: Routers and Routing Basics v 3.1 - Lab 2.2.1 Copyright  2003, Cisco Systems, Inc.
Step 6 Configuration command script
a. The router displays the configuration command script that was created and then asks if this
configuration is to be saved.
b. When asked whether or not to use the configuration, answer no.
c. If the answer was yes, when asked whether or not to use the configuration, where would this
information be saved?
______________________________________________________________
Note: Remember that setup does not provide for entry of key information such as clock rate for
DCE interfaces. These must be entered later.

Upon completion of the previous steps, logoff by typing exit. Turn the router off.

3-3 CCNA 2: Routers and Routing Basics v 3.1 - Lab 2.2.1 Copyright  2003, Cisco Systems, Inc.

You might also like