Installation Instructions

PE80 Series 59- Electroguard Delayed Egress

Exit Device (DEED)

WARNING
This product can expose you to lead
which is known to the state of California
to cause cancer and birth defects or other
reproductive harm. For more information go
to www.P65warnings.ca.gov.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com
Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited.
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

TOC Table of Contents

1 Panic and Fire Rated Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

a Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

b Required Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

c Optional Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

d Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2 Insert and PC Board Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3 DIP Switch Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4 Device Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

5 Wire Routing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6 Installation of Insert Asssembly to Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

7 Harness Wiring Reconfiguration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

8 Input/Output Connector Designations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

9 ElectroLynx System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

10 ElectroLynx Wiring Options Overview with QC12 Hinge. . . . . . . . . . . . . . . . . . . . . . . . . 27

11 System Wiring Examples ElectroLynx QC8 Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

12 System Wiring Examples ElectroLynx QC12 Hinge. . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

13 Field Wiring Door Prep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

14 Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

15 Additional Options Non ElectroLynx Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 2
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

TOC Table of Contents

16 BOCA 15 Second Delay BC-59_ & BOCA 30 Second Delay BC-59_ . . . . . . . . . . . . . . . . 34

17 NFPA 101 Requirements: 30 Second Delay BC-59_ Suffix. . . . . . . . . . . . . . . . . . . . . . . . 34

18 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Caution: Do not change factory applied finishes.

NOTE:
• Wiring method must be in accordance with CSA C22.1, Canadian Electrical Code, Part I, Safety Standard for
Electrical Installations, Section 32; and CAN/ULC-S524 Installation of Fire Alarm Systems.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 3
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

1 Panic and Fire Rated Devices

a Checklist
1. Check device for shipping damage prior to installation and make sure all parts are on hand.
2. Identify options provided with device.
3. Identify model, type and hand of trim if applicable (see exit device and trim instructions for reversing hands).
4. Contact hardware supplier if device is damaged or missing parts.

b Required Components (Numbered list correlates with numbers in Figure 1)

1. 24VDC UL Listed Regulated and Filtered Power Supply with Fire Alarm Interface (recommend Securitron BPS 24-1 or
24-2 (UL294 Listed), depending on requirements). Power supply is NOT to be used in UL603 Burglar Alarm System.
2. Power transfer UL or ULC listed (8 or 12 wire depending on system) ElectroLynx QC8 or QC12, Securitron (EPT) or
equivalent.
3. Sign (MUST BE INSTALLED ON DOOR ABOVE DEVICE).
NOTE: The delayed egress system is to be installed in accordance with NFPA 101.

c Optional Components (Numbered list correlates with numbers in Figure 1)

115 VAC
4. Remote Annunciator 800 mA
2.
1 60 Hz
5. Door Position Switch (DPS) 6.
5
6. Standard Trim Fire
Alarm
7. Electrified Trim 4.
3
Circuit
PUSH UNTIL ALARM Req’d
8. Device and Trim Cylinder SOUNDS. DOOR CAN BE
OPENED IN 15 SECONDS.
d Electrical Specifications*
6 Or 8.
7. 7

• Input Voltage: 24VDC +/- 15% (20.4 - 27.6VDC)

5.
4
regulated/filtered 3.
2

• Power Consumption @ 24VDC: 1.

• 60 - 70 mA (typical) Disarmed
• 280 -340 mA (typical) Armed
• 320 - 830 mA (typical) Delayed Egress Initiated 9.
8

• 70 - 90 mA (typical) Delayed Egress Mode Figure 1

• Output Relays: Form C, 1 Amp 24VDC

• Operating Temp: -40°C to 66°C (-40°F to 150.8°F)
*Follow Local Electrical Codes for Wiring.
NOTE: Components shown do not reflect all possible applications. Refer to other system wiring diagrams within
this manual. Consult manufacturer for special applications.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 4
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

2 Insert and P.C. Board Assembly

Order Separately Circuit Board Assembly

1-1/8”
29mm
1-1/8” (29mm) Mortise
Cylinder 41 (Order separately)
Indicator Light (LED)

Typical Mortise Standard

Cylinder 41 Activator Leg
Cylinder Nut
Cylinder and Collars
Arming Switch
• Use standard 1-1/8” mortise cylinder
Activator
with standard SARGENT cam, no collar.
SARGENT No. 97 rosette is not required.
• Use SARGENT spacer 13-0137 for optional Lens Cover
1-1/4” long cylinder.
• Use SARGENT spacer 13-0489 for optional
1-1/2” long cylinder. Cylinder Assembly
Figure 2 & Key

Assembly steps for non-factory-keyed orders:

1. Insert cylinder through the cylinder support piece in the rail insert with keyway
horizontal and toward the closest end of the rail insert.
2. Slide arming switch activator over cylinder and onto the cylinder support piece. Notch in arming switch activator
keys over the stop feature in cylinder support.
3. Secure parts in place with cylinder nut. Be certain arming switch activator sits around flange in the cylinder
support piece to allow rotation of activator.
4. Insert circuit board assembly into rail insert over cylinder and switch activator. Ensure the fingers of the arming
switch activator straddle the switch mounted to the circuit board. Press down until it snaps into all four slots in the
rail insert.
5. Verify assembly by rotating key counter-clockwise and clockwise. Key should move freely and arming switch should
trip for both rotation directions. If key does not rotate freely, verify arming switch activator is properly seated on
cylinder support piece.

P3
P1 P2

Figure 3

P5 connector - Plug this into

the end bracket’s metal tab

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 5
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

2 Insert and P.C. Board Assembly, continued

NOTES:
• Factory keyed orders will be shipped assembled.
• Prior to insert assembly, device must be cut to proper length to prevent damage to circuit board. 36" Device cannot be
field cut. A maximum of 6" can be cut from a 48" device.

3 DIP Switch Settings

S2

S2-1: Nuisance Audible may be selected ON (default) or OFF 1 Nuisance Audible

S2-2 and S2-3: Nuisance Delay time may be selected 0 (Immediate), 2 Nuisance Delay
1 (default), 2 or 3 seconds
3 Nuisance Delay

4 Reset Delay
S2-4 and S2-5: Reset Delay time may be selected 5, 10 (default), 20 or
40 seconds
5 Reset Delay

S2-6: Cover Armed LED Color is Red (default) when ON and Green when OFF 6 Armed LED Color

S2-7: Re-arm After Closing (RAC)* (see below) 7 RAC

S2-8: Switch must be set ON (default) to Bypass when an external 8 DPS Bypass
Door Position Switch (DPS) is NOT used, and OFF when an
external DPS is used.

S2 Dip Switch - Default Settings PCBA DIP SWITCH VIEW

S2 Dip SW 1 2 3 4 5 6 7* 8
OFF (UP) OFF OFF OFF

ON (DOWN) ON ON ON ON ON

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 6
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

3 DIP Switch Settings, continued

Nuisance Delay (seconds) S2-6 OFF Cover Armed LED Color is Green
0 1 2 3 ON Cover Armed LED Color is Red (default)
S2-2 OFF OFF ON ON
S2-7 OFF* Momentary egress mode 5, 10, 20 or 40 seconds. Device will immediately
S2-3 OFF ON OFF ON Rearm After Closing (RAC) door, if closed before selected time expires or
Reset Delay (seconds) it will enter alarm mode, if time expires with door open (default).
See other details*
5 10 20 40
ON** 40 seconds momentary egress mode is extended indefinitely, if the door
S2-4 OFF OFF ON ON is left open. Then the device immediately Rearms after Closing (RAC)
S2-5 OFF ON OFF ON door. See other details**
S2-8 OFF External DPS is wired to device
Default ON DPS Bypass, external DPS is NOT wired to device (default)

*With S2-7 OFF (S2-4 and S2-5 set for 5, 10, 20 or 40sec), if door/DPS is open after selected time the alarm will sound. Close door to
reset and rearm device using cylinder key or remote reset signal.

**S2-7: When an external DPS is used and switch S2-7 ON, and 40 second reset delay (S2-4 and S2-5) are set ON, after activation of
momentary egress by cylinder key switch or external remote reset signal, if the Door/DPS is open beyond 40sec the device will remain
in momentary egress mode indefinitely and shall not enter alarm mode; then once the Door/DPS is closed it will rearm immediately.

If door/DPS is opened then closed before selected time expires, the device will rearm immediately.

If DPS is not used, is bypassed with S2-8 ON, the door will rearm immediately after 5, 10, 20 or 40 sec whether the door is open or
closed, with either S2-7 ON or OFF.

Ensure eight S2 Dip Switches are set per application before moving on to the next page of instructions.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 7
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

4 Device Mounting
1. Refer to installation instructions included with device and trim for complete door and frame preparations. Refer to
template for wire access hole location.
2. Feed wires from power transfer through wire access hole in door. (Figure 4)

ElectroLynx System Default Wiring Options for DEED QC12 Hinge (12 wires)
Pluggable 8-pin & 4-pin connectors. Default wiring shown.

VDC
RR

EI
DS
(RAR COM)
8, Yellow (RAR NC)

(SEC COM)
4, Tan (SEC NO)
QC12 Hinge Door Harness Premium Delayed Egress
QC12 Hinge Pigtail 3" Typical Rail Assembly
ElectroLynx Field or
Wiring Termination 15' Frame Harness
Options
(12 wires max)

Rail to Hinge Harness

(with 8-pin, 4-pin, & 26-pin connectors )

Must connect to metal tab

8 6 4 2 8-pin on exit device end bracket
7 5 3 1

QC12 Hinge RR
26-pin
(EI)
DS
Premium Delayed Egress (RAR COM)
Device 8, Yellow (RAR NC)
QC12 Hinge Pigtail
or
15' Frame Harness Door Harness
3" Typical

4 2 4-pin
3 1
Pluggable 8-pin and
4-pin connectors

(SEC COM)
4, Tan (SEC NO)

Figure 4

NOTES:
• Wires must be protected from abrasion.
• For use with Class II circuits only.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 8
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

4 Device Mounting, continued

Note: For additional instructions on hardware install, refer to
mechanical instructions.
1. When required, mount outside trim to door
(see trim installation instructions).
2. Unthread screw and remove dogging slope bracket (Figure 5).
Figure 5

3. Pull the mount rail cover back to expose front end of the
carrier/push sub-assembly (Figure 6).

Figure 6

4. Install chassis on door. Leave chassis screws loose. Insert rail onto
chassis. Pin bracket to slot in chassis lift arm (Figure 7).

Figure 7

5. Slide mount rail cover back toward chassis. Tighten chassis screws.

Figure 8

6. Replace dogging slope bracket and screw (Figure 9).

Figure 9

7. Do not install end cap until device has been wired and tested for operation (See wiring diagrams).

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 9
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

5 Wire Routing
PE8300
OVERVIEW

53- Connection

54-Lever Monitoring
(if applicable)

53- Connection

Electric Trim
(If applicable)

Step 1. Install mortise lock. Route wire

Step 2. Route trim wires as shown.
as shown.

54-Lever Monitoring
(if applicable)

Electric Trim Wire Clip

(If applicable)

53- Connection

Step 4. Pull back excess wire

54- Lever Monitoring
53-
(if applicable)
through rail. Route wires as
jumper
shown. Install wire clip.
Electric Trim Step 3. Install chassis and rail (Section 4).
(If applicable)
Make wire connections.
A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 10
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

5 Wire Routing - continued

PE8400
OVERVIEW

54-Lever Monitoring
Electric Trim (if applicable)
(If applicable)

Electric Trim
(If applicable)

53- Connection

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 11
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

5 Wire Routing - continued

PE8400

Electric Trim
(If applicable)

54-Lever Monitoring
(if applicable)

53- Connection

Step 1. Route wires as shown and secure trim to door. Step 2. Route wires through chassis
as shown and secure chassis to door.

Step 3. Install rail (Section4). Step 4. Make wire connections. Step 5. Pull back excess wire
through rail. Route wires as
shown. Install wire clips.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 12
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

5 Wire Routing - continued

PE8500
OVERVIEW

Step 1. Install chassis to rail (Section 4). Step 2. Secure trim. Make 53- connection.
Route wires through door as shown.

Step 3. Pull additional wire slack through rail

from insert end and tuck latch bolt monitor (53-)
connection into chassis.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 13
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

5 Wire Routing - continued

PE8600
OVERVIEW

Electric Trim
(If applicable)

54-Lever Monitoring
(if applicable)

53- Connection

Electric Trim
(If applicable)

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 14
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

5 Wire Routing - continued

PE8600

53- Connection

Electric Trim
(If applicable)

54-Lever Monitoring
(if applicable)

Step 1. Route wires as shown and Step 2. Install chassis (Section 4) and route wires
secure trim to door. through chassis as shown.

Step 3. Install rail (Section 4). Step 4. Make wire connections. Step 5. Snap trim jumper to clip
and route exces wire as shown.

Main Slide & Roller

Step 6. Tuck wire connections along side of

main slide. Pull back excess wire through rail.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 15
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

5 Wire Routing - continued

PE8700
OVERVIEW

Electric Trim
(If applicable)

54-Lever Monitoring
(if applicable)

53- Connection

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 16
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

5 Wire Routing - continued

PE8700

54-Lever Monitoring
(if applicable)

Electric Trim
(If applicable)

Brass lift lever

53- Connections

Step 1. Install chassis and rail (Section 4). Route trim wires Step 2. Make 53- connection.
from rail under brass lift lever as shown.

Electric Trim
(If applicable)

54- Lever Monitoring

(if applicable)

Step 3. Route trim wires through chassis and door as shown. Step 4. Make trim wire connections and secure trim to door.
Pull back excess wire through rail.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 17
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

5 Wire Routing - continued

PE8800
Electric Trim
OVERVIEW (If applicable)

54- Lever Monitoring

(if applicable)
53- Connection

Electric Trim
Optional Trim
(If applicable)
Wire Route

Step 1. Install chassis and rail (Section 4). Step 2. Route trim wires through chassis and Step 2A. Additional view
door as shown above.

Electric Trim
(If applicable)

54- Lever Monitoring

(If applicable)

Step 3. Connect wires and secure trim to door.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 18
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

5 Wire Routing - continued

PE8900
OVERVIEW
Electric Trim
(If applicable)

54- Lever Monitoring

(if applicable)

53- Connection

Step 1. Install mortise lock. Route Step 2. Install chassis and connect 53- Step 3. Install rail to chassis
wire as shown. jumper at chassis. (Section 4).

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 19
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

5 Wire Routing - continued

PE8900

Electric Trim
(If applicable)

53- Jumper

54- Lever Monitoring

(if applicable)

Step 4. Make wire connections.

Step 5. Secure trim to door.

Step 6. Pull back excess wire through rail.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 20
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

6 Installation of Insert Assembly to Device

1. The Dip Switches are on the side of the assembly.
Ensure eight S2 Dip Switches are set for application (see Section 2).
2. Slide insert assembly into device, making sure not to pinch or crimp wires.
3. Connect device lock assembly harness to connector J1. Place wire connectors and excess wire between insert and
P.C. board. (Figure 3, Device End View)
4. Check all connections before proceeding.
5. Proceed to device mounting (see packed instructions).

See DIP Switch settings on previous page

Silicone dielectric grease is applied at the factory onto J200 and J201 connectors, terminals, and wires here.

For use on exterior doors

Exit Device
Figure 10

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 21
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

7 Harness Wiring Reconfiguration

PE80 Series Exits
PCBA to QC12 Hinge Side Harness
26-pin Connector to 8 & 4-pin ELynx connectors

PE80 Series Exits

25
ElectroLynx QC12
26 LBM N.C.
Factory Default Ship Configuration
23 24 LBM N.O.
26-1 PWR- Black 8-1
21 22 LBM COM 26-2 PWR+ Red 8-2
(24VDC)
19 20 54- N.C. 26-4 RR White 8-3
Quick Conn EGND Green 8-4
GANG I/O 17 18 54- N.O.
26-6 EI Orange 8-5
SEC N.C.15
26-8 DS Blue 8-6
16 54- COM
26-5 RAR COM Brown 8-7
4-4, Tan (SEC N.O.) 13 14 (ET+) Grey, 4-2 26-9 RAR N.C. Yellow 8-8

4-3, Pink (SEC COM) 11 12 (ET-) Violet 4-1 26-12 ET- Violet 4-1
26-14 ET+ Grey 4-2
8-8, Yellow (RAR N.C.) 9 10 26-11 SEC COM Pink 4-3
26-13 SEC N.O. Tan 4-4
(RAR N.O.) 7 8 (DS) Blue, 8-6
26-7 RAR N.O. No wire
8-7, Brown (RAR COM) 5 6 (EI) Orange, 8-5
26-15 SEC N.C. No wire
3 4 (RR) White, 8-3 26-16 54- COM No wire
26-17 GANG I/O No wire
8-1, Black (PWR-) 1 2 (PWR+) Red, 8-2 26-18 54- N.O. No wire
26-20 54- N.C. No wire
26-22 LBM COM No wire
26-24 LBM N.O. No wire
26-26 LBM N.C. No wire
Pin 25
Pin 26 Legend PE80 Series Exits

53- Latch Monitor Switch (Form C) in chassis

55- Push Bar Switch (Form C) in rail
EGND - Earth Ground connection to metal rail, required
Pin 1 Pin 2
ET - Electrified Exit Trim (Fail Safe or Fail Secure) Ecoflex 10 to 28VDC
54- ET Outside Lever Monitor Switch (Form C)

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 22
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

8 Input and Output Connector Designations

Harness Circuit Input/ Harness Function

Connector Board Pin Output Wire
Pin Number* Number Color
8-2 J200-2 Input Red +24 VDC power
8-1 J200-1 Input Black -Return
8-3 J200-4 Input White Remote Reset
8-5 J200-6 Input Orange External inhibit - disarm unit
from i/s or o/s (key switch,
card reader, keypad)
8-6 J200-8 Input Blue Door position sensor (Door
status/Monitor)

Harness Circuit Input/ Harness Function

Connector Pin Board Pin Output Wire
Number* Number Color
8-4 Chassis Ground Green ESD (Earth Ground)
8-7 J200-5 Output Brown Remote Alarm Relay (C.)
8-8 J200-9 Output Yellow Remote Alarm Relay (N.C.)
4-1 J200-12 Input Violet ET-
4-2 J200-14 Input Grey ET+
4-4 J200-13 Output Tan Secure Relay (N.O.)
4-3 J200-11 Output Pink Secure Relay (C.)

* Example: 8-2 is the 8-pin connector position #2. 4-3 is the 4-pin Connector position #3

NOTE:
Remote alarm relay shown in power “off” state. Power ”on” relay energizes; contacts reverse state.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 23
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

8 Input and Output Connector Designations, Continued

Harness I/O Circuit Function

Connector Board Pin
Pin Number* Number
8-2 J200-2 +24 VDC Power Supply Input (+) - This input may be tied to the normally closed
contact of a building’s fire alarm system. If the fire alarm is activated, this contact
will open, voiding the15 second delay for egress.
8-1 J200-1 Return - Power Supply -return (-)
8-3 J200-4 Remote Reset - This input may be tied to a momentary normally open contact
at a remote location to reset the device when in alarm. Additionally when the
device is armed, this input may be used for momentary egress with the time per
the dip switch settings.

NOTE: Previous Fire Alarm Input option has been replaced with Remote Reset.
8-4 Chassis Ground Chassis Ground - The chassis ground wire must terminate at earth ground of the
equipment power supply or the main power source.
8-5 J200-6 External inhibit Input - Used to provide remote override of the delayed egress
when in the armed condition. Most common external inhibits are: key switches,
card readers, keypad, or remote control console. More than one external inhibit
device must be wired in parallel
8-6 J200-8 Door position sensor - An external door status switch can be connected to the
DEED to provide additional security. If the door status switch is utilized, an irre-
versible alarm will sound if the door is forced open while the device is armed. Unit
will not arm if door is not shut. Once the irreversible alarm sounds, it will have to
be reset at the door. If the door status switch is not utilized, set
DIP Switch S2-8 to the ON position.
8-7 J200-5 Remote Alarm Relay - A SPDT (Single Pole Double Throw) 1A, 24 VDC contact
relay is provided for external alarm indication. The contacts change state when
8-8 J200-9 the unit goes into an irreversible alarm or if the door is forced open while the
device is armed. A door position sensor is required for monitoring a door forced
open condition. This contact can be utilized to drive a horn, lamp or other
monitoring device.
4-1 J200-12 ET- and ET+ - Electrified Exit Trim (Fail Safe or Fail Secure) can be used for
authorized ingress (via card reader, keypad, and other switches).
4-2 J200-14
4-3 J200-11 SEC-C and SEC-NO: SPDT (Single Pole Double Throw) -1A, 24VDC relay. Secure
(SEC) relay changes state after 15 or 30 second delayed egress delay.
4-4 J200-13

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 24
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

8 Input and Output Connector Designations, Continued

NOTE: ElectroLynx QC12 Hinge is required if Electrified ET, Secure (SEC) Relay and/or if any other additional non-
default wiring is required.

S2

J200

J201
Top View

Green LED
(Motor Status)
Orange LED
(Door Status)
Red LED Bottom
View
(Push Rail Status)

Yellow LED
(Latch Bolt Status)
Figure 11

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 25
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

9 ElectroLynx Connector System for All Electrical Installation

1. Mount exit device per instruction sheet provided.

2. Plug exit device connector into raceway connector in door. Feed through 1" (25mm) hole in door.
Install rail mounting end clamp bracket with two (2) screws supplied. Install end cap.
3. Plug raceway connector from edge of door into electric hinge connector and feed wires back through door prep.
Mount electric hinge to door.
A. If wiring now, wire frame side wires, to wires on pigtail harness, on hinge as required by using connectors
allowed by local code. Plug pigtail harness connector into electric hinge connector. Feed harness through frame
prep and mount electric hinge.
B. If wiring later, plug pigtail harness connector into electric hinge connector. Feed harness through frame prep
and mount electric hinge.

Installation Notes:
1. Wiring to pigtail harness is per facility wiring requirement.
2. For an ElectroLynx system, go to function or monitor page(s) with your device.
3. Combinations of certain monitors can be used in each device. These instructions detail installation of each monitor
separately.

ElectroLynx Connector System Notes:

System is designed to be installation friendly, with plug connectors from electric hinge through door to device. The only
wiring required is loose wires on pigtail harness assembly on frame side of electric hinge (included with QC Hinge).
Combinations of certain switches and monitors can be used.
The plug and receptacle connectors are designed to mate and lock together. Plug connectors into each other with
locking mechanism aligned. Do NOT force connectors together any other way.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 26
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

10 ElectroLynx Wiring Options Overview with QC12 Hinge

1. Refer to installation instructions included with device and trim for complete door and frame preparations.
Refer to template for wire access hole location.
2. Feed wires from power transfer through wire access hole in door. (Figure 4)

ElectroLynx System Default Wiring Options for DEED QC12 Hinge (12 wires)
Pluggable 8-pin & 4-pin connectors. Default wiring shown.

VDC
RR

EI
DS
(RAR COM)
8, Yellow (RAR NC)

(SEC COM)
4, Tan (SEC NO)
QC12 Hinge Door Harness Premium Delayed Egress
QC12 Hinge Pigtail 3" Typical Rail Assembly
ElectroLynx Field or
Wiring Termination 15' Frame Harness
Options
(12 wires max)
Close up of
end bracket
(with metal
tab for P5
Installation)

Rail to Hinge Harness

(with 8-pin, 4-pin, & 26-pin connectors )

Must connect to metal tab

8 6 4 2 8-pin on exit device end bracket
7 5 3 1

QC12 Hinge RR
26-pin
(EI)
DS
Premium Delayed Egress (RAR COM)
Device 8, Yellow (RAR NC)
QC12 Hinge Pigtail
or
15' Frame Harness Door Harness
3" Typical

4 2 4-pin
3 1
Pluggable 8-pin and
4-pin connectors

(SEC COM)
4, Tan (SEC NO)

NOTES:
• Wires must be protected from abrasion.
• For use with Class II circuits only.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 27
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

8 System Wiring Examples:

11 8 System Wiring
System Wiring Examples ElectroLynx QC8 Hinge
Examples:
Basic DEED system with Fire Alarm and Remote Reset with ElectroLynx QC8 Hinge
Basic DEED system with Fire Alarm and Remote Reset with ElectroLynx QC8 Hinge
Delayed Egress System with Fire Alarm and Remote Reset with ElectroLynx QC8 Hinge
During a fire alarm condition, the fire alarm contact opens which removes power from DEED (rail) and allows immediate
egress. During
During a fireRail canabe
alarm firerearmed
condition, by momentary
alarm condition,
the fire alarm closure
the fire alarm at
contact the Remote
contact
opens opens Reset
which which (RR)
removes switch.
removes
power When
power
from armed,
from DEEDaEgress
Delayed momentary
(rail) and RR immediate
allows
(rail) and allows
signal will shunt
egress. rail forbe
Rail 5, 10, 20, orby40sec (for timeclosure
set by reset delay dip Reset
switches) allowing egressarmed,
for set atime, then railRR
immediate egress. Railcancan berearmed
rearmed by momentary
momentary at theat
closure Remote
the Remote (RR)
Resetswitch. When
(RR) switch. momentary
When armed, a momentary
rearms automatically.
RR signal willsignal
shuntwill shunt
rail rail10,
for 5, for20,
5, 10,
or 20, or 40sec
40sec (for time
(for time setreset
set by by reset delay
delay dipdip switches)allowing
switches) allowing egress
egress forforset
settime,
time,then railrail
then
rearms automatically.
rearms automatically.

(-)
120VAC (L,N,G)
Securitron +24VDC (-) 2, Red (PWR+ 24VDC)
120VAC (L,N,G)
BPS
To closed Fire Securitron +24VDC 2, Red (PWR+ 24VDC)
24VDC
Alarm Contact BPS Normally open
1AMP
To closed Fire 24VDC switch from card C NO
Alarm ContactPower Supply Normally
1AMP reader, keypad, etc.open
switch from card C NO
Power Supply 8, Yellow (RAR NC)
reader, keypad, etc.
When fire alarm is
activated, contact opens, Note: Power Supply 8, Yellow (RAR NC)
When fire alarm is Connect Green wire to Earth QC8 Hinge Pigtail
disconnects 24VDC to 24VDC, 1A minimum Connect
activated, contact opens, Note: Power Supply Ground (EGND) within BPS Power or
DEED, allowing per DEED for this Connect Green Ground
wire to Earth 15' FrameQC8 Hinge Pigtail to QC8
disconnects 24VDC to 24VDC, 1A minimum Supply orGround
Local Building Harness
immediate egress wiring example. (EGND) within BPS Power or Hinge Connect
DEED, allowing per DEED for this Supply or Local Building Ground 15' Frame Harness to QC8
immediate egress wiring example. Hinge
Fire alarm wiring is
required on fire rated
Fire alarm wiring is
openings
required on fire rated
openings

Closeup of end bracket

(with metal tab for P5 Installation)
Connect P5 to this metal tab on end bracket

QC8 Hinge
Wiring Notes:
QC8 Hinge
1. RailWiring
harness, door harness, electric hinge
Notes:
and pigtail/frame harness connector
Premium Delayed Egress 1. Rail harness, door harness, electric hinge
terminations and wire colors all match.
Exit Device (DEED) and pigtail/frame harness connector
Premium Delayed Egress 2. Wiringterminations
to remainingand hinge
wirepigtail
colorswires is as
all match.
QC8 Hinge Pigtail
Exit Device (DEED) required. Tape or cap off ends of unused
or Door Harness 2. Wiring to remaining hinge pigtail wires is as
15' FrameQC8 Hinge Pigtail
Harness 3" Typical pigtail wires (not shown) to ensure that they
required. Tape or cap off ends of unused
or Door Harness don’t short to anything.
15' Frame Harness 3" Typical pigtail wires (not shown) to ensure that they
3. A fire don’t
alarmshort
tie-into
is required
anything.on fire rated
ElectroLynx pluggable 8-pin
openings.
and 4-pin connectors 3. A fire alarm tie-in is required on fire rated
ElectroLynx
Only 8-pin connectorspluggable
need 8-pin
4. Rail DPS bypass dip switch 8 must be
openings.
and 4-pin
to be plugged in connectors
Only 8-pin connectors need set ON, which is default setting.
4. Rail DPS bypass dip switch 8 must be
to be plugged in set ON, which is default setting.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 28
 PE80 Series 59- Electroguard Delayed Egress
h ElectroLynx QC8 Hinge

Installation Instructions
r from DEED (rail) and allows immediate egress.
ard presentation at Inside card reader shunts the rail and

ard presentation at Inside card reader shunts the rail and

et by the reset delay dip switch settings. RR also can be

11
opens and signals the rail sounding the rail alarm. System Wiring Examples ElectroLynx QC8 Hinge, Continued
y dip switch setting, the Remote Alarm Relay (RAR)
9 System Wiring Examples (continued):
Delayed Egress System with Fire Alarm, Switch Controls, DPS, Horn with ElectroLynx QC8 Hinge
DEED system with Fire Alarm, Switch Controls, DPS, Horn with ElectroLynx QC8 Hinge

During a fire alarm condition, the fire alarm contact opens which removes power from DEED (rail) and allows immediate egress.
For External Inhibit (EI) control, a valid code entry at the Inside keypad or valid card presentation at Inside card reader shunts the rail and
allows egress for a time period programmable at the keypad.
For Remote Reset (RR) control, a valid code entry at the Inside keypad or valid card presentation at Inside card reader shunts the rail and
NO allows egress for a time period programmable at the keypad plus the rail time set by the reset delay dip switch settings. RR also can be
used to rearm rail from alarm condition, with the door closed.
When the rail is armed and the door is forced open, the 3287 door status switch opens and signals the rail sounding the rail alarm.
Connect
4, Green (EGND) When the rail is armed and push bar pressed for time beyond rail nuisance delay dip switch setting, the Remote Alarm Relay (RAR)
to QC8
sends 24VDC to theHinge
4380H remote horn.

-) QC8 Hinge Pigtail

or (-)
120VAC (L,N,G)
15' Frame Harness
Securitron +24VDC
BPS
To closed Fire
Note: The RAR NC contact opens when 24VDC Normally open
DEED is powered,Alarm Contact
and closes when delayed 2AMP switch from card C NO
egress alarm is initiated Power Supply reader, keypad, etc.
PS, Horn with ElectroLynx QC8 Hinge C NO
(-) (+) +24VDC Connect
When fire alarm is Note: Power Supply 4, Green (EGND) to QC8
removes power from DEED (rail) and allows immediate
activated, contact egress.24VDC, 2A minimum
opens,
4380H Horn, or remote alarm, by others Hinge
eypad or valid card presentation at Inside card reader
disconnects 24VDC shunts
to theperrailDEED
and for this
(-) DEED, allowing wiring example. Connect Green wire to
ypad or valid card presentation at Inside immediate egressshunts the rail and
card reader Earth Ground (EGND) (-) QC8 Hinge Pigtail
theDPS
railNormally
time setOpen (NO)
by the contact
reset to dip switch settings. RR also can
delay be
2A allows for within BPS Power Supply or or
(C) is held electrically closed when Fire alarm wiring is Local Building Ground 15' Frame Harness
increased load
magnet is in proximity of switch, when
or status switch required on fire rated
opens and signals the rail sounding the rail alarm. current due to
the door is closed
openings addition of electrical
nuisance delay dip switch setting, the Remote Alarm Relay (RAR) Note: The RAR NC contact opens when
On DEED PCBA set DPS Bypass dip accessories. DEED is powered, and closes when delayed
switch 8 to OFF for external DPS use egress alarm is initiated

(-) (+) +24VDC

4380H Horn, or remote alarm, by others
3287
Door Status
Switch, (-)
Or DPS by others
Wiring
C Notes:
NO DPS Normally Open (NO) contact to
(C) is held electrically closed when
1. Rail harness, door harness, electric hinge
magnet
Closeup of end bracket
magnet is in proximity of switch, when
C NO pigtail/frame harness connector
and
terminations and wire colors all match. Connect (with metal tab for P5 Installation)
the door is closed
4, Green (EGND) to QC8
2. Wiring to remaining hinge pigtail wires is as
On DEED PCBA set Connect
DPS BypassP5dipto this metal tab on end bracket
Hinge switch 8 to OFF for external DPS use
required. Tape or cap off ends of unused
o pigtail wires (not shown) to ensure that they
) don’t(-)
short to anything. QC8 Hinge Pigtail
pply or or
d 3. A fire alarm tie-in is required on fire rated 15' Frame Harness
openings.

Note: The RAR NC contact opens when

QC8 Hinge
DEED is powered, and closes when delayed Wiring Notes:
egress alarm is initiated
1. Rail harness, door harness, electric hinge
and pigtail/frame harness connector
(-) (+) +24VDC Premium Delayed Egress terminations and wire colors all match.
Exit Device (DEED)
4380H Horn, or remote alarm, by others 2. Wiring to remaining hinge pigtail wires is as
7 QC8 Hinge Pigtail
or Door Harness required. Tape or cap off ends of unused
tatus
h, (-) 15' Frame Harness 3" Typical pigtail wires (not shown) to ensure that they
others don’t short to anything.
DPS Normally Open (NO) contact to
(C) is held electrically closed when 3. A fire alarm tie-in is required on fire rated
magnet is in proximity of switch, when ElectroLynx pluggable 8-pin openings.
net and 4-pin connectors
the door is closed
Only 8-pin connectors need
On DEED PCBA set DPS Bypass dip to be plugged in
switch 8 to OFF for external DPS use

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 29
Wiring Notes:
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

12 System Wiring Examples ElectroLynx QC12 Hinge

10 System Wiring Examples (continued)
10 System Wiring
DEED system withExamples (continued)
Fail Safe Electrified Exit Trim (ET) and ElectroLynx QC12 Hinge
Delayed Egress System
DEED system with
with Fail Fail Safe
Safe Electrified ExitElectrified Exit Trim
Trim (ET) and ElectroLynx (ET)
QC12 and ElectroLynx QC12 Hinge.
Hinge
During a fire alarm condition, the fire alarm contact opens which removes power from DEED (rail) and Fail Safe ET, and allows immediate
egress and ingress.
During a fire alarm condition, the fire alarm contact opens which removes power from DEED (rail) and Fail Safe ET, and allows immediate
For External
egress Inhibit (EI) control, a valid code entry at the Inside keypad or valid card presentation at Inside card reader shunts the rail and
and ingress.
allows egress for a time period programmable at the keypad. A valid code entry at the Outside keypad or valid card presentation at
For External Inhibit (EI) control, a valid code entry at the Inside keypad or valid card presentation at Inside card reader shunts the rail and
Outside card reader removes power from the Fail Safe ET and allows ingress for a time period programmable at the keypad.
allows egress for a time period programmable at the keypad. A valid code entry at the Outside keypad or valid card presentation at
Outside card reader removes power from the Fail Safe ET and allows ingress for a time period programmable at the keypad.

(-)
120VAC (L,N,G)
Securitron (-)+24VDC
120VAC (L,N,G) BPS
To closed Fire Securitron +24VDC
24VDC
Alarm Contact BPS
To closed Fire 1AMP
24VDC
Alarm Contact Power Supply
1AMP Connect Green wire to Earth
Power Supply Ground (EGND) within BPS Power 8, Yellow (RAR NC)
Connect
SupplyGreen wire
or Local to EarthGround
Building
When fire alarm is
Note: Power Supply Ground (EGND) within BPS Power 8, Yellow (RAR NC)
activated, contact opens, Supply or Local Building Ground
When fire alarm is 24VDC, 2A minimum Note: Wiring to remaining wires is as required Connect
disconnects 24VDC to Note: Power Supply
activated, contact opens, per DEED to QC12
DEED, allowing 24VDC, 2A minimum Note: Wiring to remaining wires is as required Connect
disconnects 24VDC to (-) Hinge
immediate egress per DEED to QC12
DEED, allowing
(+) C (-) Hinge
immediate egress
(+) C 4, Tan (SEC NO)

4, Tan (SEC NO)

QC12 Hinge Pigtail
1 2 3 1 2 3
or
4 5 6 NO 4 5 6 QC12
15' Hinge
FramePigtail
Harness
1 23 1 2 3
7 8 9 7 8 9 or
4 56 NO 4 5 6
4291 0 # *8 0 # 4292 15' Frame Harness
7 *89 7 9
(Inside) 0 # (Outside)
4291 * 0 # * 4292
Keypad Keypad
(Inside) C (Outside)
Or Or Wiring Notes:
Keypad Keypad
Inside Card C Outside Card Wiring1.Notes:
Rail harness, door harness, electric hinge
Or Or
Reader Relay Reader Relay and pigtail/frame harness connector
Inside Card (-) Outside Card 1. Rail harness, door harness, electric hinge
(by others) (by others) terminations and wire colors all match.
Reader Relay Reader Relay and pigtail/frame harness connector
(-) 2. Wiring toandremaining hinge
(by others) (by others) terminations wire colors all pigtail
match.wires is as
required. Tape or cap off ends of unused pigtail
Closeup of end bracket 2. Wiring to remaining
wires (not shown) tohinge pigtail
ensure that wires is as’t short
they don
required. Tape or cap off ends of unused pigtail
to anything.
(with metal tab for P5 Installation)
wires (not shown) to ensure that they don ’t short
3. A fire alarm tie-in is required on fire rated
to anything.
openings.
3. A fire alarm tie-in is required on fire rated
4. Rail DPS bypass dip switch 8 must be set
openings.
ON, which is default setting.
4. Rail DPS bypass dip switch 8 must be set
ON,5. which
As another option,
is default instead of wiring to the
setting.
External Inhibit (EI) input Orange wire pin 5,
5. As
youanother option,
could move wireinstead
to theofRemote
wiring to the (RR)
Reset
External
input,Inhibit
White (EI)
wireinput
pin 3.Orange wire pin 5,
you could move wire to the Remote Reset (RR)
input, White
Note thatwire
whenpin 3. RR it will add 5, 10,
using
20, or 40sec (depending DEED reset delay
Connect P5 to this metal Note
dipthat when
switch usingto
setting) RRthe
it will add 5, 10,
keypads/card
QC12 Hinge 20,readers
or 40sec (depending DEED reset
tab on end bracket (ET+) Red, 2 time setting. RR also candelay
be
dip switch setting) to the keypads/card
QC12 Hinge (ET-) Black, 1 used to rearm DEED from alarm
readers time setting. RR also can be
(ET+) Red, 2 5-pin condition.
(ET-) Black, 1 connector used to rearm DEED from alarm
Premium Delayed Egress 5-pin condition.
Exit Device (DEED) connector
QC12 Hinge Pigtail Premium Delayed Egress
or Exit Device (DEED)
Door Harness
Premium 775 (or 773) Fail Safe
QC12
15' Hinge
FramePigtail
Harness Electrified Exit Trim (ET)
3" Typical Premium 775 (or 773) Fail Safe
or Door Harness
15' Frame Harness 3" Typical Electrified Exit of
From outside Trim (ET)
door, route ET wire through
ElectroLynx pluggable chassis into the opposite side of the LBM wiring,
Fromthenoutside of5-pin
plug ET door,connector
route ET wire
intothrough
mating rail
8-pin and 4-pin chassis into5-pin
the opposite side of thewires
LBM wiring,
ElectroLynx pluggable
connectors harness connector. Ensure are tucked
8-pin and 4-pin then plug ET 5-pin connector into mating
in, to avoid pinching wires by push bar or railchassis
connectors harness 5-pin connector. Ensure wires are tucked
mechanism.
in, to avoid pinching wires by push bar or chassis
mechanism. Note: Fail Secure ET
requires different wiring, as
Note: Fail Secure
shown on nextET
page
requires different wiring, as
shown on next page

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 30
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

12 System Wiring Examples ElectroLynx QC12 Hinge, Continued

11 System Wiring Examples (continued):
DelayedDEED
Egress System
System with Electrified
with Fail Secure Fail Secure Electrified
Exit Trim Exit Trim
(ET) and ElectroLynx QC12 (ET)
Hinge and ElectroLynx QC12 Hinge

During a fire alarm condition, the fire alarm contact opens which removes power from DEED (rail), and allows immediate egress.
For External Inhibit (EI) control, a valid code entry at the Inside keypad or valid card presentation at Inside card reader shunts the rail and
allows egress for a time period programmable at the keypad. A valid code entry at the Outside keypad or valid card presentation at
Outside card reader applies power to unlock the Fail Secure ET and allows ingress by turning lever for a time period programmable at the
keypad.

(-)
120VAC (L,N,G)
Securitron +24VDC
BPS
To closed Fire 24VDC
Alarm Contact 1AMP
Power Supply
Connect Green wire to Earth
Ground (EGND) within BPS Power
When fire alarm is Supply or Local Building Ground
Note: Power Supply
activated, contact opens,
24VDC, 2A minimum Note: Wiring to remaining wires is as required Connect
disconnects 24VDC to
per DEED to QC12
DEED, allowing
immediate egress (-) Hinge
(+) C 2, Gray (ET+)

4, Tan (SEC NO)

QC12 Hinge Pigtail

1 2 3 1 2 3
or
4 5 6 NO 4 5 6 15' Frame Harness
7 8 9 7 8 9
4291 0 # * 0 # 4292
*
(Inside) (Outside)
Keypad Keypad
C (-)
Or Or
Inside Card Outside Card Wiring Notes:
Reader Relay Reader Relay 1. Rail harness, door harness, electric hinge
(by others)
(-)
(by others) andCloseup
pigtail/frameof endconnector
harness bracket
(with metal tab
terminations forcolors
and wire P5 all
Installation)
match.

Closeup of end bracket

Connect P5 totothis
2. Wiring metal
remaining tabpigtail
hinge on wires
end isbracket
as
required. Tape or cap off ends of unused pigtail
(with metal tab for P5 Installation) wires (not shown) to ensure that they don ’t short
to anything.
3. A fire alarm tie-in is required on fire rated
openings.
4. Rail DPS bypass dip switch 8 must be set
ON, which is default setting.
5. As another option, instead of wiring to the
External Inhibit (EI) input Orange wire pin 5,
you could move wire to the Remote Reset (RR)
input, White wire pin 3.

Note that when using RR it will add 5, 10,

Connect P5 to this metal 20, or 40sec (depending DEED reset delay
tab on end bracket dip switch setting) to the keypads/card
QC12 Hinge
readers time setting. RR also can be
(ET+) Red, 2
(ET-) Black, 1 used to rearm DEED from alarm
5-pin condition.
Premium Delayed Egress connector
Exit Device (DEED)
QC12 Hinge Pigtail Premium 776 (or 774) Fail Secure
or Door Harness Electrified Exit Trim (ET)
15' Frame Harness 3" Typical
From outside of door, route ET wire through
chassis into the opposite side of the LBM wiring,
ElectroLynx pluggable then plug ET 5-pin connector into mating rail
8-pin and 4-pin harness 5-pin connector. Ensure wires are tucked
connectors in, to avoid pinching wires by push bar or chassis
mechanism.

Note: Fail Safe ET

requires different wiring, as
shown on previous page

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 31
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

13 Field Wiring Door Prep

NOTE:
• Do not scale drawing.
• Dimensions are in inches (") and millimeters (mm)
• LHR H.M. opening shown. Details are typical for all opening materials (both hands).
• This preparation is an addition to preparation shown on device template.
• See device template to locate centerline.*
• Shields for wiring access recommended for insulated and composite doors.
• Locate and prepare wiring access holes when installing device.

Exit Device Dim. A

ED4000 Series 1-11/16" (43mm)
ED5000 Series 2-5/16" (59mm)

Vertical Conducting Hinge or

Reference Approved Power Transfer
(made by other manufacturers)

Rail Horizontal C L
Hinge Edge Detail
of Push Rail 1/4”
INSIDE FACE OF DOOR

Horizontal Clear Channel Access

Reference Required for Wire
Connection Hinge

01.000
Metal: Thru inside wall only
1" (25mm) Dia. Wood: 1 - 1/16” deep 3/8”
(Wiring Access) Raceway

Horizontal Reference
Device Centerline
(See Note 5)
Figure 12

Exit Device End Clamp Mounting 5/8" Ref

Holes (For reference only) 5/16" Ref (16mm)
(8mm)
1-1/4" Ref
(32mm)
A

Hinge Edge
Of Door

HINGE EDGE DETAIL

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 32
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

14 Operating Instructions
Momentary/
There are three (3) modes of operation (Figure 12): Reset
• Delayed Egress
• Momentary Egress
• Bypass (Maintained) Egress
Delayed Egress Mode
LHR
1. Apply power to device. The initialization / self test sequence is as follows: Shown Bypass/
Maintained
• Cover LED is GREEN for 2 seconds with horn sounding for 500ms. Figure 12

• Cover LED is then RED for 2 seconds, followed by AMBER for 2 seconds with the 4 diagnositc LEDs illuminated.
• Cover LED is RED or GREEN (based on the setting of the Armed LED Color DIP Switch Position 6) and green diagnostic LED
is illuminated. The device is now armed, which will not allow pushpad to retract latchbolt for immediate egress.
2. If the device is not functioning, refer to the Troubleshooting Guide.
Momentary Egress Mode (Figure 12)
1. With device armed, rotate key counter clockwise and return to center position (remove key).
2. Red LED (or LED color opposite the Armed LED Color Setting per DIP Switch Position 6) will flash quickly. Device will
release for momentary egress for 10 seconds (factory set). 5, 10, 20, or 40 second reset delay may be selected using DIP
Switch positions 4 and 5.
3. After the reset delay time has elapsed, or if the cylinder key is rotated a second time counter clockwise while the door/
DPS is closed during a reset delay, the device shall re-arm. When an external DPS is used and (DIP Switch position 7 is
off) door is opened and closed during momentary egress, the selected reset delay shall be canceled and the device shall
re-arm.
4. Device will now be back in delayed egress mode.
Bypass (Maintained) Egress Mode (Figure 12)
1. Rotate key clockwise, return key to center position and remove.
2. Cover LED is solid GREEN (default) or LED color opposite the Armed LED Color Setting per DIP Switch Position 6.
3. Device is disarmed, acting as a standard exit device which allows free egress.
Resetting device from Bypass Mode to Delayed Egress Mode (Figure 12)
1. Rotate key counter clockwise, return to center position and remove.
2. Cover LED is solid RED (default) or LED color setting per the Armed LED Color DIP Switch Position 6.
3. Device will be in delayed egress mode.
Delayed Egress Operation When Armed
Exit door is normally closed and latched. Delayed Egress device secures door in locked mode with solid red LED (default GREEN
when DIP Switch Position 6 setting is OFF) indicating locked mode status.
Depressing pushpad for (1) one to three (3) seconds or less (depending on DIP Switch position 2 and 3 settings) will sound
device nuisance beeps without initiating alarm.
Depressing pushpad longer than (1) one to three (3) seconds (depending on DIP Switch position 2 and 3 settings) will initiate
an irreversible local audible alarm with a continuous tone, and a visual amber indicator.
After delay time (15 or 30 seconds), device releases, LED changes to green, (default, or red depending on the setting of DIP
Switch position 6), and the local audible alarm remains as a continuous tone until reset by keyswitch.
Remote monitoring contact outputs can be used to alert security personnel. Person depressing pushpad is denied egress for
15 or 30 seconds (depending upon setup) and security personnel are alerted.
NOTE: 30 seconds may be accepted by local jurisdiction.
A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 33
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

14 Operating Instructions, continued

Re-arm After Closing for Indefinite Delay

With 40 second momentary egress setting (S2-4 ON & S2-5 ON), S2-7 ON, and an external DPS is wired to the PCBA (S2-8
OFF), after activation of momentary egress by cylinder key switch or external remote reset signal, if the Door/DPS is open
beyond 40 seconds, it will remain in momentary egress mode indefinitely and shall not enter alarm mode. Then once the
Door/DPS is closed, it will re-arm immediately. With (S2-4 ON & S2-5 ON) S2-8 OFF and S2-7 OFF for same scenario as above,
the device will enter alarm mode after 40 seconds if the Door/DPS is still open. If Door/DPS is closed before 40 seconds, it will
re-arm immediately.

15 Additional Options Non ElectroLynx Wiring

Electrically Controlled ET Trim “Safe/Secure”
The Delayed Egress Exit Device is available with Fail Safe (SAF) or Fail Secure (SEC) outside trim operation. In a fire
condition, the Fail Safe trim will release for entry. When Access control is used, the Fail Secure trim allows entry by
means of a remote card reader, keyswitch, push button, etc.
Note: If a Door Position Switch is not used, the trim will open the door without affecting the device in an armed
condition (refer to wiring diagrams for wiring).
Note: If an external DPS is not used, Standard trim and Safe/Secure trim will allow entry without affecting the device in
an armed mode. The device will only be affected when the push pad is depressed (refer to wiring diagrams for wiring).

16 BOCA 15 Second Delay BC-59_ and BOCA 30 Second Delay BC-59_

Upon depressing the pushpad for 1 second or longer, the device will sound an audible continuous tone and allow the
door to be opened within 15 (or 30) seconds. The alarm will remain as a continuous tone until reset. Resetting of the
alarm and re-arming of the device occurs automatically once the door has been returned to the closed position for 30
seconds. The 30-second re-arming timer will re-start if the pushpad is depressed or the door is re-opened before actual
re-arming of the device occurs. A DPS (Door Position Switch) is required for the BOCA option.
NOTE: BOCA option is not suitable for installations in accordance with NFPA 101.

17 NFPA 101 Requirements: 30 Second Delay BC-59_ Suffix

Upon depressing the pushpad for 3 seconds or longer, the device will sound an audible continuous tone and allow the
door to be opened after 30 seconds. The alarm will remain as a continous tone until reset. Resetting of the alarm and
re-arming of the device is accomplished by manual means only.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 34
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

18 Troubleshooting

Problem Solution
• Check all connections on circuit board and wire harness.
• Check for power 24VDC at power inputs (-black) and (+red) and check
Power is applied, but unit will not arm polarity.
(No red LED) • Check wire transfer for any bad connections or broken wires.
• Check power output at power supply.
• Must be 24VDC regulated.

• Check pushpad position sensor wire harness on circuit board and all
Device alarms continuously when power
other connections.
is applied.
• Check that the position of the pushpad matches the status of the RED
Diagnostic LED (See table on Page 27 for details.).

Units with Door Position Switch (made • Make sure DPS is wired (electrically closed - with door closed) into wire
by other manufacturers) harness. Make sure DPS is working properly by using a meter to check
continuity when door is opened and closed.

Device allows mechanical latchbolt • Check for correct power, 24VDC regulated.
retraction with power applied and LED • Check for correct amperage on power supply (must be rated equal or
shows armed. greater than device, 1A minimum).

Exit device latchbolt/rods will not latch • Refer to standard exit device installation instructions troubleshooting
properly. guide.
LED on rail cover is flashing fast Amber
color (once every 300ms) and rail buzzer • Close/secure door, check DPS for proper operation, then reset rail using
is activated. Door was forced open (DPS cylinder key, or remote rest signal.
was opened)
LED on rail cover is flashing slow Amber
color (once every 1 sec) and rail buzzer • Close/secure door, ensure latch is extended, then reset rail using
is activated. Latch bolt was retracted for cylinder key, or remote rest signal.
10sec.

NOTE: If device is not working properly after troubleshooting, contact your local hardware distributor or
local SARGENT representative, or contact SARGENT.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 35
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

18 Troubleshooting, continued

Symptom / Failure

A.  R
 ail won’t arm (Green Insert LED won’t turn ON / Horn sounds immediately or after a delay)
• When trying to arm, the rail goes into alarm immediately after momentary egress times out or after a short delay
after the momentary egress times out.

Are the Yellow, Red, Orange, and Green circuit board Diagnostic LEDs OFF?
YES – Replace defective circuit board.
*NO – All of these LEDs should be OFF. Troubleshoot according to which LED is ON.
If any LED stays ON after troubleshooting according to *, then replace defective circuit board.

B.  R
 ail won’t arm(Green Insert LED won’t turn ON / Horn stays OFF)
• The rail is receiving an external inhibit signal.
• The rail is in fire alarm condition.

C.  R ail Arms, but will not go into alarm when depressing push bar
• Does the Red Diagnostic LED turn ON when depressing push bar?

YES – Replace defective circuit board.

NO – The push rail position sensor is malfunctioning. The rail assembly will need to be replaced.

D. Cover LED fast flashes alternately RED then GREEN every 0.5 seconds (*Hall Error Mode);
Horn/Diagnostic LEDs are off.
• The rail may or may not arm prior to this error code.
• Check harnesses are connected to the controller PCBs.
• Push rail hall switch circuit defective or out of activation range. Consult 1-800-810- 9473.
• If the push bar was in the dogged (retracted) position using a 24 VDC power cycle (via fire alarm/reset or temporary
power outage), this hall error mode will occur. To clear error, un-dog push bar with manual hex key, ensure bar
extends fully then turn cylinder key clockwise to maintained egress position, then counter-clockwiase to Armed
(center) position (or cycle 24 VDC power) to rearm device.
*If horn sounds or flashing sequence differs from the above; or if error mode does not clear,
consult 1-800-810-9473.

Important: Rail is not armed when in this condition.

Attention: Electrified Trim applications require a separate raceway and power transfer device. Installation of conductors
or harnesses (by others) through the exit device rail is prohibited as it could lead to product performance issues up to
and including product failure.

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 36
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

18 Troubleshooting, continued

Refer to the following table and notes for an explanation of each LED’s function.

Diagnostic LEDs Function

Yellow (Latch Bolt Status) ON - Latch bolt is retracted

OFF- Latch bolt is extended
Red (Push Rail Switch) ON- Rail Push Bar is depressed.
OFF- Rail Push Bar is released.
Orange (Door Status Switch) ON- Door Status Switch is open. Door is open/violated.
OFF- Door Status Switch is closed or DPS Bypass DIP switch position 6 is ON.
Green (Solenoid) ON- Motor is in blocked/locked/armed postion.
OFF- Motor is in unblocked/disarmed position

NOTES:
1. When the rail is armed (in Delayed Egress Mode) and the door is closed and latched, the Green Diagnostic LED should be ON
only. All other LEDs should be OFF.
2. With the rail armed, depressing the rail push bar slightly will turn the Red Diagnostic LED ON. The rail should go into alarm
immediately (no nuisance delay) or after being pressed for 1, 2, or 3-second nuisance delay setting. The rail will be in the
irreversible alarm mode and Cover LED is Amber with local audible beeping tone. After a standard delay of 15 seconds (or
30-second optional delay), the motor unblocks and passage is allowed. Cover LED is green (or red depending on DIP Switch
position 6 setting) with alarm at a steady tone which continues until reset by key switch.
3. When a Door Status switch is used and the door is opened, the Orange Diagnostic LED will turn ON, which indicates that the
door is not closed. When not using a door status switch, DIP switch position 7 must be set to ON, Orange Diagnostic LED shall
be off.

YELLOW

RED

ORANGE

GREEN

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 37
 PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 38
PE80 Series 59- Electroguard Delayed Egress
Installation Instructions

A8298-1 05/23
1-800-727-5477 • www.sargentlock.com

Copyright © 2023 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission of SARGENT Manufacturing Company is prohibited. 39
SARGENT Manufacturing
100 Sargent Drive
New Haven, CT 06511 USA
800-810-9473 • www.sargentlock.com
Copyright © 2023 Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Sargent Manufacturing
Company is prohibited. Patent pending and/or patent - www.assaabloydss.com/patents.
HID, iCLASS, and Edge are trademarks or registered trademarks of HID Global Corporation. A8298-1 - 05/23