TA8189N

TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic

TA8189N
Quad Preamplifier For Double Cassette Tape Recorder

The TA8189N is a quad pre amplifier designed for use in record /

play back amplifier. It is suitable for double cassette tape
recorder.

Features
· Play back amp
· Built in input select switch.
· Built in equalizer control switch.
· Mixing output, for music selection.
· Recording amp
Weight: 1.2g (typ.)
· Built in ALC detector circuit.
· Operating supply voltage range: VCC (opr) = 4.0~13.5V (Ta = 25°C)

1 2002-10-30
 TA8189N
Block Diagram

2 2002-10-30
 TA8189N
Terminal Explanation
Terminal
Symbol Function Equivalent Circuit
No.

1 Tape A in (ch1)
Tape play back input
(play)
24 Tape A in (ch1)

2 Tape B in (ch2)
Tape play back input
(play / rec)
23 Tape B in (ch2)

3 PB NF (ch1)
Tape play back NF
22 PB NF (ch2)

4 / 21 Metal out Metal EQ switch

5 Pre out (ch1)

Play back amp output

20 Pre out (ch2)

6 Mix out Mixing output

7 GND GND —

Change over switch

Metal / normal
8 for metal mode and
SW
normal mode.

3 2002-10-30
 TA8189N

Terminal
Symbol Function Equivalent Circuit
No.

9 Rec out (ch1)

Recording amp output

16 Rec out (ch2)

10 Rec NF (ch1)
Recording amp NF
15 Rec NF (ch2)

11 Rec in (ch1)
Recording amp input
14 Rec in (ch2)

12 GND GND —

Automatic level
13 ALC T.C control (ALC) time
constant terminal

NF charge up circuit
17 CG det.
switching terminal

4 2002-10-30
 TA8189N

Terminal
Symbol Function Equivalent Circuit
No.

Tape A / tape B Play back AMP input

19
SW selector

Application Information And Application Method

1. Input level of play amp.
In case that input voltage (Vin > 0.0245Vrms (-30dBm)) is applied to A-head and B-head at same time on a set,
use A-head for reproducing only and, B-head for recording or reproducing.
In case that the over-voltage is applied to A-head and B-head at same time, the transistor Q3, Q4 are made a
saturation condition and NF condenser is discharged by base-current of Q3, Q4 and the output DC voltage of
pin 3 / 22 are raised.
In case of the high input, use B-head, because of building in the diode against saturation on Q4.

2. Power source line

In case of including the ripple on the power source line, stabilize by using a transistor as following figure.

5 2002-10-30
 TA8189N
Maximum Ratings (Ta = 25°C)

Characteristic Symbol Rating Unit

Supply voltage VCC 14.5 V

Power dissipation PD (Note) 1200 mW
Operating temperature Topr -20~75 °C
Storage temperature Tstg -55~150 °C

(Note) Derated above Ta = 25°C in the proportion of 9.6mW / °C.

Electrical Characteristics (unless otherwise specified, VCC = 6V, f = 1kHz, Ta = 25°C)

Test
Characteristic Symbol Cir- Test Condition Min. Typ. Max. Unit
cuit
Quiescent current ICCQ — Metal mode, Vin = 0 — 13 20 mA
Normal mode, Rg = 2.2kΩ,
Output noise
Vno — nab EQ, BW = 20Hz~20kHz, — 200 600 µVrms
voltage
GV = 40dB
Total harmonic Vout = 0.2Vrms, f = 1kHz
THD — — 0.06 0.2 %
distortion normal mode
Maximum output THD = 1.0%, RL = 10kΩ,
Vom — 0.5 1.0 — Vrms
voltage f = 1kHz, normal mode
Open loop voltage f = 1kHz, RL = 10kΩ,
Gvo — 70 95 — dB
Play back amp.

gain Vin = 13.8µV (-95dBm)

Vout = 0.775Vrms (0dBm),
Cross talk C.T. (ch) — f = 1kHz, Rg = 2.2kΩ, normal -40 -60 — dB
mode
Vout = 0.775Vrms (0dBm),
Tape A / tape B
C.T. (in) — f = 1kHz, Rg = 2.2kΩ, normal — -66 — dB
cross talk
mode
Vripple = 0.775Vrms (0dBm),
Ripple rejection
R.R. — fripple = 100Hz, Rg = 2.2kΩ, — -38 — dB
ratio
normal mode
Vin = 7.75mVrms (-40dBm),
Voltage gain Gvn — f = 1kHz, RL = 10kΩ, normal — 40 — dB
nab
f = 1kHz,
Pre amp
C.T. (P / R) — Vout (pre) = 0.775Vrms (0dBm), — -53 — dB
→rec amp C.T.
normal (pre)
f = 1kHz,
Rec amp
C.T. (R / P) — Vout (rec) = 0.775Vrms (0dBm), — -76 — dB
→pre amp C.T.
normal (pre)

6 2002-10-30
 TA8189N

Test
Characteristic Symbol Cir- Test Condition Min. Typ. Max. Unit
cuit
Output noise Rg = 2.2kΩ, BW = 20Hz~20kHz,
Vno — — 1.35 2.7 mV
voltage ALC off GV = 60dB
Total harmonic Vout = 0.5Vrms, f = 1kHz,
THD — — 0.37 1.0 %
distortion ALC off RL = 10kΩ
Maximum output THD = 1%, RL = 10kΩ, f = 1kHz,
Vom — 1.2 1.5 — Vrms
voltage ALC off
Open loop voltage f = 1kHz, RL = 10kΩ, ALC off,
Gvo — 80 108 — dB
gain Vin = 3.16µVrms (-110dBV)
ALC range R (ALC) — 3dB up, f = 1kHz, dual input — 52 — dB
Vin = 0.0775Vrms (-20dBm),
Total harmonic
THD (ALC) — f = 1kHz — 0.48 1.0 %
distortion (ALC)
dual input, RL = 10kΩ
Recording amp.

Vin = 0.0775Vrms (-20dBm),

ALC balance B (ALC) — — 0 2 dB
dual input, RL = 10kΩ, f = 1kHz
Vin = 0.0775Vrms (-20dBm),
ALC level V (ALC) — 0.75 1.0 1.2 Vrms
f = 1kHz, RL = 10kΩ
Ripple rejection Vripple = 0.775Vrms (0dBm),
R.R. — — -30 — dB
ratio f = 100Hz, Rg = 2.2kΩ
f = 1kHz (flat), RL = 10kΩ,
Voltage gain Gvn — — 61 — dB
Vin = 1mVrms (-60dBV)
Vout = 0.775Vrms (0dBm),
Cross talk f = 1kHz, Rg = 2.2kΩ,
C.T. (ch) — -40 -54 — dB
(ALC off) ALC off,
Vin = 1mVrms (-60dBV)
Vout = 0.775Vrms (0dBm),
f = 1kHz, Rg = 2.2kΩ,
Cross talk (ALC on) C.T. (ALC) — -40 -54 — dB
ALC on,
Vin = 0.0775Vrms (-20dBm)

7 2002-10-30
 TA8189N
Test Circuit

8 2002-10-30
 TA8189N

9 2002-10-30
 TA8189N

10 2002-10-30
 TA8189N

11 2002-10-30
 TA8189N

12 2002-10-30
 TA8189N

13 2002-10-30
 TA8189N

Package Dimensions

Weight: 1.2g (typ.)

14 2002-10-30
 TA8189N

RESTRICTIONS ON PRODUCT USE 000707EBA

· TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc..

· The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this
document shall be made at the customer’s own risk.

· The products described in this document are subject to the foreign exchange and foreign trade laws.

· The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other
rights of the third parties which may result from its use. No license is granted by implication or otherwise under
any intellectual property or other rights of TOSHIBA CORPORATION or others.

· The information contained herein is subject to change without notice.

15 2002-10-30
This datasheet has been download from:

www.datasheetcatalog.com

Datasheets for electronics components.