STRUCTURAL SPECIFICATIONS AND STANDARD DETAILS

1.0 GENERAL 4.0. STRUCTURAL STEEL 8.0 BEAMS & GIRDERS 9.5. PROVIDE SUPPLEMENTARY REINFORCEMENT AT SMALL UNFRAMEDOPENINGS IN FLOOR SLABS AS
SHOWN BELOW.
4.1. ALL STRUCTURAL MILL SECTIONS BUILT UP PLATE SECTIONS SHALL BE DESIGNED IN ACCORDANCE
1.1 MATERIALS AND WORKMANSHIP SHALL CONFORM TO THE REQUIREMENTS OF THE FOLLOWING
WITH AISC'S LATEST "SPECIFICATION FOR THE DESIGN, FABRICATION AND ERECTION OF
BUILDING CODES: 8.1. CAMBER ALL BEAMS AND GIRDERS AT LEAST 10 MM FOR EVERY 4.00M OF SPAN .
STRUCTURAL STEEL FOR BUILDINGS."
1.1.1. NATIONAL STRUCTURAL CODE OF THE PHILIPPINES 2015 (NSCP), 7TH EDITION 4.2. DESIGN LOADS FOR BUILDINGS SHALL MEET THE REQUIRED STRUCTURAL DESIGN CRITERIA. 8.2. FOR TWO OR MORE LAYERS OF REINFORCING BARS, USE SEPARATORS SPACED AT
4.3. STEEL PLATES, SHAPES, BARS AND METAL FABRICATIONS: ASTM A-36. 900 MM O.C. AND IN NO CASE SHALL BE LESS THAN TWO (2) SEPARATORS.
TRIMMER MAYBE
1.1.2. ASEP STEEL HANDBOOK 2440, 3RD EDITION
4.4. STRUCTURAL BOLTS AND NUTS: OMITTED WHERE
ASSOCIATION OF STRUCTURAL ENGINEERS OF THE PHILIPPINES
ASTM A-325, 7/8 Ø AND BELOW OPENING IS FRAMED
MIN. 1-12mmØ TOP
BY BEAM
1.2. ALL DRAWINGS SHALL NOT BE SCALED FOR CONSTRUCTION PURPOSES UNLESS OTHERWISE A-490 1" Ø AND ABOVE PROPOSED PIPE SLEEVE LOCATIONS AND BOTTOM FOR
INDICATED. 4.5. SHOP AND FIELD WELDING SHALL BE IN ACCORDANCE WITH AWS D1.1 AND PERFORMED 2d (NO PIPE SLEEVE SHALL BE SLABS 0.012m. THICK
SCH. 40 G.I. PIPE SLEEVE
BY QUALIFIED WELDERS. ALLOWED W/IN THIS ZONE (TYP.)) AND OVER
2 - EXTRA STIR. EA. SIDE
1.3. FOR ALL OTHER REQUIREMENTS REFER TO THE ARCHITECTURAL, SANITARY, STRUCTURAL, OF SLEEVE
4.6. UNLESS OTHERWISE INDICATED, WELDING ELECTRODES SHALL BE E70XX. PROVIDE ALL AROUND 0
ELECTRICAL & MECHANICAL WORKING DRAWINGS. 2d 50 P. 2d
WELD WITH MINIMUM THICKNESS OF BE 6mm UNLESS NOTED OTHERWISE. TY
4.7. FLAME CUTTING AND WELDING SHALL BE DONE IN ACCORDANCE WITHTHELATEST "STANDARD TOP BARS FACE OF HOCK SLAB REINF.
CODE FOR WELDING IN BUILDING CONSTRUCTION" OF THE AMERICAN WELDING SOCIETY. SUPPORT
2.0 CONCRETE 4.8. ALL BUTT WELDS SHALL BE FULL PENETRATION WELDS AND SHALL BE PROPERLY BACK-CHIPPED OPENING
OVER TRIMMER BAR

OR GOUGED. BACK-UP PLATES SHALL BE PROVIDED AS REQUIRED.

d/5
4.9. SHOP PAINTING FOR STRUCTURAL STEEL SHALL BE RUST INHIBITIVE PRIMER WITH MINIMUM D.F.T.
2.1. UNLESS OTHERWISE SPECIFIED, THE MINIMUM 28 - DAYS CYLINDER COMPRESSIVE
OF 2.0 MILS. Ø 16 EXTRA BARS E.F.
STRENGTH ARE AS FOLLOWS, BOT. BARS (TYPICAL)
4.10. TOUCH-UP PAINTING: APPLY PAINT TO EXPOSED AREAS IN MANNER SATISFACTORY TO THE FACE OF 4d(minimum) STIR. AS SCHED.
FOOTINGS 21 MPa (3,000 PSI) ENGINEER WITH SAME MATERIAL AS SHOP PAINT. SUPPORT
COLUMNS 21 MPa (3,000 PSI) L/4 L/2 L/4
SUSPENDED SLABS, BEAMS & GIRDERS 21 MPa (3,000 PSI)) 4.11. COMPLY WITH AISC CODE AND SPECIFICATIONS FOR BEARING, ADEQUACYOF TEMPORARY LIMIT LOCATION OF PIPE SLEEVE PROVIDE EXTRA BARS
ELEVATOR & STAIRWELL CORES, R.C. WALLS CONNECTIONS AND ALIGNMENT. (NOT SHOWN) PARALLEL 2-12mmØ AT EACH
21 MPa (3,000 PSI) L
PARTITIONS & PARAPET WALLS TO SIDE OF EQUAL AREA CORNER
21 MPa (3,000 PSI)
4.12. CONTRACTOR SHALL FURNISH COMPLETE ERECTION DRAWINGS FOR THE PROPER IDENTIFICATION OF INTERRUPTED SLAB
BEDDED SLABS, CATCH BASINS & SIDEWALK 17.2 MPa (2,500 PSI) 2 - EXTRA STIR. EA.
AND ASSEMBLY OF ALL BUILDING COMPONENTS. THESE DRAWINGS WILL SHOW ANCHOR BOLT NOTES: REINFORCEMENT LESS
SIDE OF SLEEVE EXTEND TRIMMER BAR
SETTING, PRIMARY AND SECONDARY ROOF FRAMING, AND NECESSARY INSTALLATION DETAILS. 1. MAXIMUM PIPE SLEEVE DIAMETER: AREA TRIMMER BARS
2.2. ALL CONCRETE MUST BE DEPOSITED, VIBRATED AND CURED IN ACCORDANCE WITH THE LATEST TOP BARS 0.61-0.15m. BEYOND SIDE
SUBMIT SHOP DRAWINGS FOR APPROVAL BEFORE FABRICATION.
EDITION OF AMERICAN CONCRETE INSTITUTE (ACI-318) A. 51 OF BEAM DEPTH. Ø 16 EXTRA BARS OF OPENING OR AS FAR
B. 100 MM E.F. (DIAGONALS) AS POSSIBLE & HOOK
2.3. STRIPPING FORMS AND SHORES SHALL BE AS FOLLOWS :
5.0. FORMWORKS 2. SEEK STRUCTURAL ENGINEER'S APPROVAL FOR PIPE PIPE SLEEVE

d/5
SLEEVES BIGGER THAN THE MAXIMUM STIPULATED.
FOUNDATIONS 1 DAY Ø 16 CROSS ANCHORS
WELDED TO SLEEVE
COLUMNS & WALLS 7 DAYS 5.1. FORMS SHALL BE PROVIDED FOR ALL CONCRETE INDICATED UNLESS SPECIFIES OTHERWISE. FORMS 3. PIPE SLEEVES SHALL BE LOCATED W/IN TENSION ZONES.
BOT. BARS
BEAMS & GIRDERS 14 DAYS SHALL BE SET TRUE TO LINE AND GRADE AND MAINTAINED SO AS TO INSURE COMPLETED WORK
b
14 DAYS WITHIN THE ALLOWABLE TOLERANCES SPECIFIED AND SHALL BE MORTAR TIGHT. 4. NO PIPE SLEEVE SHALL BE ALLOWED AT TWICE THE BEAM 9.6. UNLESS OTHERWISE NOTED, ALL BEDDED SLAB SHALL BE REINFORCED WITH 10mmØ BAR AT 0.25m.
DEPTH (2d) FROM THE SUPPORT. O.C.E.W. AT CENTER OF SLAB CONSTRUCTION JOINT FOR SLAB SHALL NOT BE MORE THAN 3.00m. APART.
5.2. FORMS AND THEIR SUPPORTS SHALL BE DESIGNED SO AS NOT TO DAMAGE PREVIOUSLY PLACED
2.4. CONCRETE SHALL BE DEPOSITED IN ITS FINAL POSITION WITHOUT SEGREGATION, REHANDLING OR
STRUCTURE.
FLOWING, PLACING SHALL BE DONE PREFERABLY WITH BUGGIES, BUCKET OR WHEEL BARROWS. NO
CHUTES WILL BE ALLOWED EXCEPT TO TRANSFER CONC. FROM HOPPERS TO BUGGIES, WHEEL 5.3. NO CONSTRUCTION LOAD SHALL BE SUPPORTED ON, NOR ANY SHORING REMOVED FROM ANY PART PIPE SLEEVE THRU BEAM DETAIL 30 BAR DIA. 30 BAR DIA.
BARROWS OR BUCKETS IN WHICH CASETHEY SHALL NOT EXCEED SIX METERS (20 FEET) IN OF STRUCTURE UNDER CONSTRUCTION EXCEPT WHEN THAT PORTION OF THE STRUCTURE IN

VERIFY DEPRESSION
(min.) (min.)
AGGREGATE LENGTH. NO DEPOSITING OF CONCRETE SHALL BE ALLOWED WITHOUT THE USE OF COMBINATION WITH THE REMAINING FORMING AND SHORING SYSTEM HAS SUFFICIENT STRENGTH NOTES:
VIBRATORS UNLESS AUTHORIZED IN WRITING BY THE DESIGNERS AND ONLY FOR UNUSUAL TO SUPPORT SAFELY ITS WEIGHT AND THE ADDITIONAL IMPOSED LOADS.
9.0 CONCRETE SLAB FOR DOWELS:

D=FOR BEAM
t=FOR SLAB
CONDITIONS WHERE VIBRATIONS IS EXTREMELY DIFFICULT TO ACCOMPLISH. PROVIDE DOWELS OF SAME SIZE AND SPACING
5.4. FORMS SHALL BE REMOVED IN SUCH MANNER AS NOT TO IMPAIR SAFETY AND SERVICEABILITY OF
THE STRUCTURE.. AS HORIZONTAL OR BENT HORIZONTAL BARS.
9.1. ALL REINFORCEMENT SHALL BE 20MM CLEAR MINIMUM FROM TOP AND BOTTOM OF SLAB.

3.0 REINFORCING BARS 6.0 FOUNDATION 9.2. FOR TWO-WAY SLAB, REINFORCEMENT ALONG THE SHORTER SPAN SHALL BE PLACE BELOW THOSE
ALONG THE LONGER SPAN AT CENTER AND OVER THE LONGER SPAN BARS NEAR THE SUPPORT
24d 24d

300mm(MIN.) 300mm(MIN.)
UNLESS OTHERWISE INDICATED OR SHOWN IN DETAILS THE SPACING OF THE BARS AT THE COLUMN D=FOR BEAM 100m(min.) COMPACTED
3.1. SCHEDULE OF REINFORCING BARS ARE AS FOLLOWS: 6.1. FOUNDATION IS DESIGNED USING ASSUMED ALLOWABLE SOIL BEARING CAPACITY OF 120 kPA. STRIPS CAN BE APPROXIMATELY 1-1/2 OF THE MIDDLE STRIP IN NO CASE GREATER THAN 2 TIMES THE 2t=FOR SLAB GRAVEL FILL
6.1.1. SOIL TEST SHALL BE CONDUCTED PRIOR TO START OF CONSTRUCTION. SLAB THICKNESS.
10 MM Ø AND SMALLER BARS (UNLESS NOTED OTHERWISE) GRADE 33 (228 MPa) 6.1.2. IN CASE THE ACTUAL SOIL BEARING CAPACITY IS FOUND LESS THAN THE ASSUMED, 50 kPA, 30 BAR DIA.
12 MM Ø GRADE 33 (228 MPa) NOTIFY THE STRUCTURAL ENGINEER FOR PROPER REVISION OF FOUNDATION. 9.3. TEMPERATURE BARS FOR SLAB SHALL BE GENERALLY PLACED NEAR THE TENSION FACE AND SHALL (min.)
16 MM Ø AND LARGER BARS GRADE 33 (228 MPa) NOT BE LESS THAN 0.0025 BT.

3.2. BARS SHALL BE CLEAN OF RUST, GREASE OR OTHER MATERIALS LIKELY TO IMPAIR BOND. ALL
6.2. FOUNDATION SHALL REST ON NATURAL SOIL. UNLESS OTHERWISE NOTED BY THE ENGINEER, NO
PART OF THE FOUNDATION SHALL REST ON FILL. 9.4. PROVIDE EXTRA REINFORCEMENT AT CORNER SLAB (TWO ADJACENT DISCONTINUOUS EDGE) AS
SUSPENDED SLAB
REINFORCING BAR BENDS SHALL BE MADE COLD. REINFORCING STEEL OF DIFFERENT GRADES SHOWN BELOW. 30 BAR DIA.
SHALL BE CLEARLY MARKED TO DIFFERENTIATE THEM ON SITE. 6.3. THE CONTRACTOR SHALL NOTIFY THE ENGINEER AFTER FOOTING EXCAVATION HAVE BEEN (min.)
COMPLETED AND PRIOR TO CONCRETING TO CONFIRM THE DESIGN SOIL BEARING CAPACITY.

100
3.3. IN GENERAL, BAR SPLICES SHALL BE MADE AT POINTS OF MINIMUM STRESS. SPLICES SHALL BE 6.4. ALL TIE BEAMS AND FOOTINGS SHALL REST ON 100MM THK. WELL COMPACTED GRAVEL BASE COARSE.
SECURELY WIRED TOGETHER. STAGGER SPLICES AT LEAST 6OO MM. WHENEVER POSSIBLE IN BEAMS

100
AND SLABS SPLICE TOP BARS AT MIDSPAN AND BOTTOM BARS NEAR SUPPORT. SPLICE OF 6.5. WHERE LOOSE/SOFT MATERIAL IS ENCOUNTERED AT DEPTH OF EMBEDMENT INDICATED,
REINFORCEMENT SHALL BE MADE ONLY AS REQUIRED OR PERMITTED ON DESIGN DRAWINGS OR AS EXCAVATE TO FIRM LAYER AND REPLACE LOOSE/MATERIAL UNDERNEATH THE FOOTING WITHIN THE 5-10mmØ BARS AT 200mm.
ALLOWED BY THE ACI CODE OR AS AUTHORIZED BY THE ENGINEER. FOOTING AREA PLUS 1/2 DEPTH OF SOFT SOIL MATERIAL ON ALL SIDES WITH SELECT GRANULAR BACKFILL O.C. BOTTOM BARS
COMPACT GRANULAR BACKFILL TO 95% OF MAXIMUM DRY DENSITY.
3.4. SPLICES SHALL BE SECURELY WIRED TOGETHER AND SHALL LAP OR EXTEND IN ACCORDANCE WITH 6.6. BACKFILL SHALL BE PLACED IN LAYER AND EACH LAYER SHALL BE 200MM THK. AND SHALL BE COMPACTED 10mm Ø TEMP. BARS 16D BEND (300mm min.)
TABLE 1 (TABLE OF LAP SPLICE AND ANCHORAGE LENGTH). UNLESS OTHERWISE SHOWN ON TO 95% OF MAXIMUM DRY DENSITY. SPACED @ 400mm O.C. 100mm THK. MIN.
5-10mmØ BARS 900mm.
DRAWINGS, SPLICES SHALL BE STAGGERED WHENEVER POSSIBLE. BOTHWAYS GRAVEL FILL
LONG AT 200mm. O.C.

SLAB - ON - FILL SLAB ON GRADE

3.5. MINIMUM CONCRETE COVER FOR REINFORCING BARS SHALL BE :

CONCRETE CAST AGAINST EARTH 75 MM

7.0 CONCRETE COLUMNS
7.0 COLUMN TIES SHALL BE PROTECTED EVERYWHERE BY A COVERING OF CONC. CAST
EXPOSED TO EARTH OR OF WEATHER 50 MM MONOLITHICALLY WITH THE CORE WITH MIN. THICKNESS OF 1 ½" AND NOT LESS THAN ½ TIMES MAX.
SIZE OF COARSE AGGREGATE. WHERE COLUMNS CHANGE IN SIZE, VERTICAL REINFORCEMENT
SLAB, WALLS AND JOISTS 20 MM

BEAMS AND COLUMNS 40 MM

SHALL BE OFFSET AT A SLOPE OF NOT MORE THAN 1" AND EXTRA, 12mm AT 3" O.C. SHALL BE
PROVIDED THROUGHOUT THE OFFSET REGION. DESIGN CRITERIA
MAX. COL. DIMENSIONS A. DEAD LOAD D. SEISMIC LOAD
SHELLS FOLDED PLATE MEMBERS 12 MM
OR 1/6 h WHICH EVER IS 1. CEILING AND UTILITIES ........................................................ 0.392 KPa 1. SEISMIC ZONE..................................................................... ZONE 4, Z = 0.4
GREATER BUT NO LESS 2. TOPPING AND FINISHES...................................................... 1.10 KPa 2. SOIL PROFILE TYPE............................................................. Sd
3.6. WELDING OF REINFORCING STEEL IS NOT PERMITTED UNLESS OTHERWISE SHOWN ON THE THAN 450MM.
3. 4” PLASTERED CHB.............................................................. 2.98 KPa 3. SEISMIC SOURCE............................................................... TYPE A
DRAWINGS. WELDING OF REINFORCING STEEL SHALL CONFORM TO AWS D1.4-79 "AWS STRUCTURAL
4. SEISMIC SOURCE PROXIMITY........................................... > 15KM FROM VFS
WELDING CODE - REINFORCING STEEL" OF THE AMERICAN WELDING SOCIETY. REINFORCING STEEL
B. LIVE LOAD 5. SEISMIC COEFFICIENTS..................................................... Ca = 0.44Na

TIE SPACING
WHICH IS WELDED SHALL CONFORM TO ASTM A-706. REINFORCING STEEL NOT CONFORMING TO

100MM
10mmØ TIES 1. BASIC FLOOR AREA........................................................... 1.90 KPa Cv = 0.64Nv

MIDDLE THIRD
ASTM A-706 MAY BE USED IF MATERIAL PROPERTIES OF THE REINFORCING STEEL CONFORM TO AWS

LAP SPLICE
at 100mm 2. EXTERIOR BALCONIES........................................................ 2.90 KPa 6. NEAR-SOURCE FACTOR.................................................... Na = 1.0
O.C. (MAX.)

Ldh
Nv = 1.0
3.7. WELDED WIRE FABRIC (WWF) SHALL CONFORM TO ASTM A-185. WELDED WIRE FABRIC IN SUSPENDED 7. IMPORTANCE FACTOR..................................................... I = 1.0
50
50

SLABS SHALL HAVE FY = 60 KSI. LAP 152 MM. MINIMUM OR ONE FULL MESH, WHICHEVER IS GREATER C. WIND LOAD 8. NUMERICAL COEFFICIENT............................................... R = 8.5
1. WIND EXPOSURE............................................................... EXPOSURE C 9. PERIOD OF VIBRATION..................................................... T = Ct (hn)^¾
FOR SLABS ON GRADE.
2. BASIC WIND SPEED.......................................................... 300 KPH Ct = 0.0731 (CONCRETE)
10MMØ JOINT HOOPS
3.8. SHOP DRAWINGS : THE CONTRACTOR SHALL SUBMIT SHOP DRAWINGS FOR REINFORCING STEEL SPACED AT 100MM 3. VELOCITY PRESSURE........................................................ qz = 0.613 Kz Kzt Kd V² (N/m²); V in m/s
(SEE SCHEDULE OF COLUMNS 4. VELOCITY PRESSURE EXPOSURE..................................... Kz = 2.01 (z/zg)²/ª
PREPARED IN ACCORDANCE WITH ACI 315. INDICATE BENDING DIAGRAM, ASSEMBLY DIAGRAM, FOR NUMBER OF SETS)
5. TOPOGRAPHIC FACTOR................................................ Kzt = 1.00 10. BASE SHEAR...................................................................... V = Cv I W / (R T)
50

50

SPLICING AND LAPS OF RODS AND SHAPES DIMENSIONS AND DETAILS FOR REINFORCING BARS.
6. WIND DIRECTIONALITY FACTOR.................................... Kd = 0.85 ≤ 2.5 Ca I W / R

(MIN)
7. WIND PRESSURE.............................................................. p = qh [ (GCpf) ± (GCpi) ] ≥ 0.11 Ca I W
600
3.9. ANCHOR BOLTS, DOWELS AND OTHER EMBEDDED ITEMS ARE TO BE SECURELY TIED IN PLACE
BEFORE CONCRETE IS POURED. ≥ 0.80 Z Nv I W / R
10mmØ TIES
at 100mm
O.C. (MAX.)
COLUMN SPLICE &
h = HEIGHT BETWEEN FLOORS

COLUMN DETAILS BEAM-COLUMN CONNECTION

REGISTERED OWNER: PROJECT NAME & LOCATION: SHEET CONTENTS: RE PROJECT STAGE DATE DRAWING NO.
IMPORTANT: THESE DRAWINGS AS
DESIGN DE ELOPMENT E T
ENGR.E GENE RON P. TAG A INSTR MENT O SER ICE ARE THE PROPERT
GENERAL NOTES
PRC N .
CI IL STR CT RAL ENGINEER
DECEM ER
AND DOC MENTS O THE DESIGNER. IT
SHALL E NLAW L OR AN PERSON
MS. JOMAILA M NSA AC
CASA ROCELLA S
WITHO T THE WRITTEN CONSENT O THE
PTR N . D DESIGNER OR A THORS O SAID DOC MENTS LO ISE ILLE RG . LAAN SILANG CA ITE SCALE AS SHOWN
TIN TO D PLICATE OR COP SAID INSTR MENTS.
P GAM ISA ELA RE ISION NO.
 STRUCTURAL SPECIFICATIONS AND STANDARD DETAILS DETAILING DETAILING

10.0 CONCRETE HOLLOW BLOCKS VERTICAL

DIMENSION DIMENSION

REINFORCEMENT AS TABULATED BELOW SHALL BE PROVIDED UNLESS OTHERWISE SPECIFIED IN THE PLAN: 100mm. CHB MASONRY REINF.
INTERIOR WALLS (SEE SCHEDULE)

db
ANCHORAGE LENGTH

db
(PARTITION WALLS)

DOWEL LENGTH
64mm
CONCRETE HOLLOW BLOCK REINFORCEMENT

SEE TABLE OF
2-Ø16 CROSS HORIZONTAL
BARS (CONTINUOUS MASONRY
180° 90°

(TYP.)
BLOCK REINFORCEMENT NOTES 2 - Ø12X1000 ALONG WALL LENGTH REINF.
THK. LONG DIAGONALS TO SLAB SUPPORT)
HORIZONTAL VERTICAL
A. MIN. SPLICE AT LAP = 10" AT MID-DEPTH
75 MM 10mm Ø @ 600mm O.C. 10mm Ø @ 600mm O.C.
B. PROVIDE RIGHT ANGLE OF WALL AT FLR LVL
REINFORCEMENT AT CORNERS EACH CORNER
3'-0" LONG.
100 MM 10mm Ø @ 600mm O.C. 10mm Ø @ 600mm O.C. C. WHERE CHB WALLS ADJOINING
COLS. R.C. BEAMS, WALL GENERAL USE SEISMIC USE
125 MM 10mm Ø @ 600mm O.C. 10mm Ø @ 600mm O.C. DOWELS W/ SAME SIZE AS VERT. SUSPENDED
FLOOR SLAB 12db FOR #6,#7,#8

A or G
OR HOR. REINFORCEMENT SHALL
BE PROVIDED. 6db FOR #3,#4,#5
150 MM 10mm Ø @ 600mm O.C. 10mm Ø @ 600mm O.C.

H
DOOR
OPENING TYP. CHB PARTITION ON SUSPENDED

DIMENSION
DETAILING
2-Ø16 EACH
FACE OF
SLAB db
db
OPENING db
(TYPICAL) DOWEL DOWEL
LENGTH LENGTH GEN.
GEN.
C
L USE C
L USE C
L
24d 24d
VERTICAL BAR
WHERE OCCURS BEAM BEAM BEAM
CHB

2 - 12mm Ø
LINTEL BEAM (CHB width x 200mm)
DOOR OPENING DETAIL
STIRRUPS AND TIE HOOKS, ALL GRADES
10mm Ø @ 150mm o.c.
N O T E S: BAR D. GENERAL USE SEISMIC USE
2 - 12mm Ø SIZE (mm)
1. UNLESS INDICATED OTHERWISE USE MORTAR Ø10 135-DEG HOOK 135-DEG HOOK
90° HOOK
RC LINTEL BEAM AT THE TOP AND RC EDGE BARS A OR G A OR G H. APPROX. A OR G H. APPROX.
WALL OPENING

BOND BEAM AT THE BOTTOM OF ALL 24d 24d (TYPICAL)

COLUMN #3(Ø10) 38.1mm 101.6mm 101.6mm 50.8mm 127mm 88.9mm
WALL OPENING & TOP OF PARAPET WALL
300mm(MIN.) 300mm(MIN.) #4(Ø12) 50.8mm 114.3mm 114.3mm 76.2mm 165mm 144.3mm
2. ALL LINTEL AND BOND BEAMS SHALL
BE EMBEDDED AT LEAST 600MM INTO TYP. OF CHB TO STEEL COLUMN #5(Ø16)
#6(Ø19)
63.5mm
144.3mm
152.4mm
304.8mm
139.7mm
196.8mm
95.3mm
114.3mm
203mm
273mm
139.7mm
165.1mm
THE CHB WALL
CONNECTION #7(Ø22) 133.4mm 355.6mm 228.6mm 133.4mm 317mm 196.9mm

300mm(MIN.)
#8(Ø25) 152.4mm 406.4mm 260.4mm 152.4mm 362mm 228.6mm

24d
SEE NOTES
FOR DOWELS

TYPICAL LINTEL AND BOND DETAIL TABLE OF LAP SPLICE & ANCHORAGE LENGTH NOTES :
50mm x 100mm KEY 0.036 x 0.63
KEY 1. ACI SECTION 12.4 STATES THAT DEVELOP-
STANDARD HOOK LAP SPLICE (m) MIN. LAP SPLICE
MENT LENGTH OF INDIVIDUAL BARS W/IN A
BAR ANCHORAGE UNIT LENGTH OF COL. REINF.
(m) BUNDLE, IN TENSION OR COMPRESSION,
WALL INTERSECTIONS DIAMETER
(mm)
LENGTH
(m)
TENSION BAR COMP. BAR WEIGHT
(Kg/m)
INDIVIDUAL BARS
SHALL BE THAT FOR THE INDIVIDUAL BAR,
INCREASED 20% FOR THREE BAR BUNDLE,
90 DEG 180 DEG 135 DEG TOP BAR BOT BAR TOP BAR BOT BAR W/ TIES W/ SPIRAL
AND 33% FOR FOUR-BAR BUNDLE.
10 0.60 0.15 0.13 0.10 0.42 0.30 0.42 0.30 0.617 0.30 0.30 2. FOR COLUMNS, AT ANY LEVEL NO MORE
THAN ALTERNATE BARS SHOULD BE SPLICED.
12 0.60 0.20 0.15 0.12 0.42 0.30 0.42 0.30 0.889 0.30 0.30 NOT MORE THAN 33 % OF THE BARS SHALL

11.0 CONSTRUCTION JOINTS 24d 24d

16 0.60 0.25 0.18 0.14 0.73 0.52 0.87 0.62 1.580 0.52 0.47
BE SPLICED W/IN THE REQUIRED LAP
LENGTH. MINIMUM DISTANCE BETWEEN TWO
ADJACENT BAR SPLICES SHALL BE 600 MM.
300mm(MIN.) 300mm(MIN.) 18 0.60 0.30 0.20 0.20 0.91 0.65 1.10 0.78 2.469 0.65 0.58
11.1. SURFACE OF CONCRETE CONSTRUCTION JOINTS SHALL BE CLEANED AN LAITANCE REMOVED. 3. TOP BARS ARE HORIZONTAL BARS W/
20 0.68 0.40 0.28 0.26 1.15 0.82 1.40 1.00 3.858 0.80 0.73 MORE THAN 300 MM DEPTH OF CONCRETE
11.2. IMMEDIATELY BEFORE NEW CONCRETE IS PLACED, ALL CONSTRUCTION JOINT SHALL BE WETTED AND CAST BELOW THHE REINFORCEMENT.
STANDING WATER REMOVED. 25 0.86 0.48 0.38 1.45 1.03 1.53 1.09 4.840 0.90 0.82
4. AS MUCH AS POSSIBLE, SPLICES SUBJECTED
11.3 CONSTRUCTION JOINT SHALL BE SO MADE AND LOCATED AS NOT TO IMPAIR THE STRENGTH OF THE 32 1.12 0.56 0.43 1.90 1.35 1.74 1.24 6.327 1.03 0.93 TO TENSILE STRESSES ARE DISCOURAGE,
STRUCTURE. PROVISION SHALL BE MADE FOR TRANSFER OF SHEAR AND OTHER FORCES THROUGH THESE SHOULD BE AVOIDED OR PROVIDED
CONSTRUCTION JOINTS. INTERFACE SHALL BE ROUGHENED TO A FULL AMPLITUDE OF APPROXIMATELY 6 MM. 0.05 x 0.10m KEY 0.038 x 0.063m KEY 36 1.43 0.61 0.48 2.40 1.70 2.00 1.40 8.000 1.20 1.05 W/ STANDARD HOOKS.

11.4 CONSTRUCTION JOINTS IN FLOORS SHALL BELOCATED WITHIN THE MIDDLE THIRD OF SPANS OF SLABS, BEAMS
0.031m x 0.152m BELL TYPE PVC WATER STOP
AND GIRDERS. JOINTS IN GIRDERS SHALL BE OFFSET A MINIMUM DISTANCE OF TWO TIMES THE WIDTH OF THE

11.5
INTERSECTING BEAMS.

BEAMS, GIRDERS OR SLABS SUPPORTED BY COLUMNS OR WALLS SHALL NOT BE CAST OR ERECTED UNTIL
WALL CONSTRUCTION JOINT
CONCRETE IN THE VERTICAL SUPPORT MEMBERS IS NO LONGER PLASTIC.

11.6 BEAMS, GIRDERS, HAUNCHES, DROP PANELS AND CAPITALS SHALL BE PLACED MONOLITHICALLY AS PART OF
A SLAB SYSTEM, UNLESS OTHERWISE SHOWN IN DESIGN DRAWINGS OR SPECIFICATIONS.

L
24d

D
24d L/3 L/3 L/3
300mm(MIN.) 300mm(MIN.)

2 - 16MMØ HANGER BARS

TOP BARS
300mm(MIN.)
300mm(MIN.)

TYP. BEAM TO GIRDER

24d
24d

BOTTOM BARS
CONNECTION DETAIL
2D
SEE NOTES FOR DOWELS STIRRUP @ 100MM MAX. SPACING
NO SPLICE

WALL CORNERS TYPICAL SPLICE DETAILS FOR BEAMS FRAMING INTO COLUMNS

SPLICE DETAIL
REGISTERED OWNER: PROJECT NAME & LOCATION: SHEET CONTENTS: RE PROJECT STAGE DATE DRAWING NO.
IMPORTANT: THESE DRAWINGS AS
DESIGN DE ELOPMENT E T
ENGR.E GENE RON P. TAG A INSTR MENT O SER ICE ARE THE PROPERT
GENERAL NOTES
PRC N .
CI IL STR CT RAL ENGINEER
DECEM ER
AND DOC MENTS O THE DESIGNER. IT
SHALL E NLAW L OR AN PERSON
MS. JOMAILA M NSA AC
CASA ROCELLA S
WITHO T THE WRITTEN CONSENT O THE
PTR N . D DESIGNER OR A THORS O SAID DOC MENTS LO ISE ILLE RG . LAAN SILANG CA ITE SCALE AS SHOWN
TIN TO D PLICATE OR COP SAID INSTR MENTS.
P GAM ISA ELA RE ISION NO.
 C
B

D
A

C
C

D
B

B
A

A
GUTTER GUTTER GUTTER

1 TB-1/RW-1 TB-1 TB-1/RW-1

1 1

GUTTER
F-1/C-1 CF-1/C-1 F-1/C-2 F-2/C-4 C-1 B-1 C-1 B-1 C-2 B-1 C-4 C-1 RB-1 C-1 RB-1 C-2 RB-1 C-4

TRUSS 5
TRUSS 5

TRUSS 2

6
TR

TR

S
U

S
RB-6 RB-6 RB-8

U
S

TR
3

2
TB-5

GUTTER
TB-5/RW-1 TB-1 WF TB-1/RW-1 B-6 B-12 S-1 B-8 S-2 B-10 B-9 RB-12
ST S-3 RB-10
TRUSS 4 RB-2 RB-2 RB-2

TRUSS 5
TRUSS 7

TRUSS 5
3

3
S

S
S

S
U

U
TR

TR
TB-2/RW-1 TB-2/RW-1 TB-2 C-2 B-2 B-2 C-2 B-2 RB-3 RB-3 RB-3

GUTTER
C-1 C-4 C-2 C-1 C-2 C-4
2 F-1/C-2 CF-1/C-1 F-1/C-2 F-2/C-4 2 2
SLAB ON FILL B-6 GUTTER
USE 10MM SPACE S-1
TB-5/RW-1 AT 300MM OC TRUSS 8 TRUSS 8

WF S-2 S-3
TB-5/RW-1 WF TB-1/RW-1 B-3 RB-11
B-10 B-9 RB-8 RB-12
S-1 B-7 B-2

TB-4 TB-3
3 WF 3
C-6 B-3 C-8 B-5 C-4
3
C-4
TRUSS 8
RB-4
TRUSS 8
C-4

B-4

GUTTER
F-2/C-4 F-2/C-4
S-4 TR

GUTTER
TB-5/RW-1 TB-1 TB-1/RW-1 B-7 U

S
B-9 B-11 S-1 B-9 RB-7 RB-1 S RB-3

S
OTB S-5 S

TRUSS 2
1

TR
TB-4/RW-1 TB-4 C-3 B-6 C-4 B-6 C-3 RB-5 C-4
B-4 RB-4
4 F-2/C-3 F-2/C-4 F-2/C-5 4 4 GUTTER

1 FOUNDATION LAYOUT 2 SECOND FLOOR FRAMING PLAN 3 ROOF FRAMING PLAN

S SCALE : MTS. S SCALE : MTS. S SCALE : MTS.

400
GRID 100

300
VERIFY

300
300
200
SECTION 100
PLAN

T PICAL RW
4 TYPICAL ISOLATED FOOTING SECTION 4 DETAIL OF WALL FOOTING 6 RETAINING WALL SCHEDULE AND DETAILS
S SCALE : MTS. S SCALE NTS. S SCALE : MTS.
REGISTERED OWNER: PROJECT NAME & LOCATION: SHEET CONTENTS: RE PROJECT STAGE DATE DRAWING NO.
IMPORTANT: THESE DRAWINGS AS
ENGR.E GENE RON P. TAG A O NDATION LA O T DESIGN DE ELOPMENT E T
INSTR MENT O SER ICE ARE THE PROPERT

PRC N .
CI IL STR CT RAL ENGINEER
DECEM ER
AND DOC MENTS O THE DESIGNER. IT
SHALL E NLAW L OR AN PERSON
MS. JOMAILA M NSA AC
CASA ROCELLA SECOND LOOR RAMING PLAN
ROO RAMING PLAN
S
WITHO T THE WRITTEN CONSENT O THE
PTR N . D DESIGNER OR A THORS O SAID DOC MENTS
T PICAL ISOLATED OOTING SECTION
LO ISE ILLE RG . LAAN SILANG CA ITE SCALE AS SHOWN
TIN TO D PLICATE OR COP SAID INSTR MENTS. DETAIL O WALL OOTING
P GAM ISA ELA RETAINING WALL SCHED E AND DETAILS RE ISION NO.
 1 SCHEDULE OF FOOTING
S SCALE : MTS.

L/4 L/4
350

350

L/5 L/5
350
S=SPAN
350

3 TYPICAL BEAM SECTION

S SCALE NTS.
400
250

400
250

300
300

300

2 SCHEDULE OF COLUMN 4 SCHEDULE OF BEAM

S SCALE : MTS. S SCALE NTS.

REGISTERED OWNER: PROJECT NAME & LOCATION: SHEET CONTENTS: RE PROJECT STAGE DATE DRAWING NO.
IMPORTANT: THESE DRAWINGS AS
DESIGN DE ELOPMENT E T
ENGR.E GENE RON P. TAG A INSTR MENT O SER ICE ARE THE PROPERT SCHED LE O OOTING
PRC N .
CI IL STR CT RAL ENGINEER
DECEM ER
AND DOC MENTS O THE DESIGNER. IT
SHALL E NLAW L OR AN PERSON
MS. JOMAILA M NSA AC
CASA ROCELLA
SCHED LE O COL MN S
WITHO T THE WRITTEN CONSENT O THE
PTR N . D DESIGNER OR A THORS O SAID DOC MENTS LO ISE ILLE RG . LAAN SILANG CA ITE
T PICAL EAM SECTION
SCALE AS SHOWN
TIN TO D PLICATE OR COP SAID INSTR MENTS.
SCHED LE O EAM RE ISION NO.
P GAM ISA ELA
 L/4 L/4

B E ND UP BARS

125mm
TY P BOTTO M BARS .

COLUMN MIDDLE COLUMN

STRIP STRIP STRIP

5 TYPICAL SLAB SECTION

S SCALE NTS.
1 SCHEDULE OF BEAMS(ROOF)
S SCALE NTS. 10mmØ CHAIR BARS
SPCD. AT 200mm O.C
2ND 10mmØ NOSING BARS
FLOOR

t = 115mm
FLOOR BEAM(FB)

16mmØ MAIN BARS SPCD. AT 150mm O.C.

BENT UP 2 OUT OF 3 AT L/4 10mmØ BARS
SPACED @
200 mm O.C 10mmØ BARS SPACED @
t = 150mm 200 mm O.C
LANDING
10mmØ TEMP. BARS SPCD AS SHOWN
2 SCHEDULE OF SLABS t = 125mm LANDING BEAM(LB)

S SCALE NTS. 10mmØ CHAIR BARS SPACED @ 200 mm O.C

16mmØ MAIN BARS SPCD.
E X T R A
TOP BARS
@ 150mm O.C.
@ L / 4

16mmØ MAIN BARS SPCD.

N (L) @ 150mm O.C.
N (L) G SP
A
G SPA LON BENT UP 2 OUT OF 3 AT
LON
BOTTOM BARS BENT BARS @ L/4
@ M IDSPAN (ALTERNATE) 10mmØ NOSING BARS
L/4
T OP BARS
@ SUPPORT

t=

SHORT SPAN (W)

150mm
SHORT SPAN (W)

B E A M
B E A M

A M
10mmØ TEMP. BARS SPCD
A M B E
W3 / 4

B E AS SHOWN
W3 / 4

W3
W3

B E A M
B E A M

W2 / 4
W2 / 4

ALL TOP
B A R S
@ L / 4

A M
W2

A M B E
W2

B E CONTINUOUS
BOTTOM BARS

4 - 16mmØ LONG'L BARS WITH

W2 / 4

10mmØ TIES SPCD. AT 300MM

W2 / 4

4 ON CENTER
L3 /
LANDING BEAM
W1 / 4

L2 / 4
W1 / 4

L3
W1
W1

4
L2 / L2
L1/4

L1

3 ONE WAY SLAB 4 TWO WAY SLAB 6 TYPICAL STAIR DETAIL

S SCALE NTS. S SCALE NTS. S SCALE NTS.
REGISTERED OWNER: PROJECT NAME & LOCATION: SHEET CONTENTS: RE PROJECT STAGE DATE DRAWING NO.
IMPORTANT: THESE DRAWINGS AS
DESIGN DE ELOPMENT E T
ENGR.E GENE RON P. TAG A INSTR MENT O SER ICE ARE THE PROPERT SCHED LE O EAMS ROO
PRC N .
CI IL STR CT RAL ENGINEER
DECEM ER
AND DOC MENTS O THE DESIGNER. IT
SHALL E NLAW L OR AN PERSON
MS. JOMAILA M NSA AC
CASA ROCELLA
SCHED LE O SLA S S
WITHO T THE WRITTEN CONSENT O THE
PTR N . D
ONE AND TWO WA SLA
DESIGNER OR A THORS O SAID DOC MENTS LO ISE ILLE RG . LAAN SILANG CA ITE
TIN TO D PLICATE OR COP SAID INSTR MENTS. T PICAL SLA SECTION SCALE AS SHOWN
P GAM ISA ELA T PICAL STAIR DETAIL RE ISION NO.
∅ ∅

1.45m
0.349m 1m 1m 1m 1m 1m 1m 0.349m

1 TYPICAL TRUSS SECTION

S SCALE NTS.

SCHEDULE OF TRUSS

5 TRUSS SPOT DETAIL

S SCALE NTS.
1450

1450

1160
1000 1000 1000 322 1000 1000 349 1000 1000 758

3322 2349 2758

TRUSS 1 TRUSS 2 TRUSS 3

1450
1160

1160

T PICAL SAGROD TO P RLIN T PICAL DETAIL O

280
1000 950 950 1000 1000 950 2349 6 CONNECTIION DETAILS 7 PURLINS CONNECTIION
1950 1950 1950 S SCALE NTS. S SCALE NTS.
TRUSS 4 TRUSS 5 TRUSS 6
1450

280

280

3322 2349 2349

TRUSS 7 TRUSS 8

2 TRUSS SCHEDULE AND DETAILS

S SCALE NTS.
REGISTERED OWNER: PROJECT NAME & LOCATION: SHEET CONTENTS: RE PROJECT STAGE DATE DRAWING NO.
IMPORTANT: THESE DRAWINGS AS
DESIGN DE ELOPMENT E T
ENGR.E GENE RON P. TAG A INSTR MENT O SER ICE ARE THE PROPERT TT PICAL TR SS CONNECTION
PRC N .
CI IL STR CT RAL ENGINEER
DECEM ER
AND DOC MENTS O THE DESIGNER. IT
SHALL E NLAW L OR AN PERSON
MS. JOMAILA M NSA AC
CASA ROCELLA
TR SS SCHED LE AND DETAILS S
WITHO T THE WRITTEN CONSENT O THE
PTR N . D DESIGNER OR A THORS O SAID DOC MENTS LO ISE ILLE RG . LAAN SILANG CA ITE
TR SS SPOT AND CONNECTION DETAILS
TO D PLICATE OR COP SAID INSTR MENTS. SCALE AS SHOWN
TIN
P GAM ISA ELA RE ISION NO.