Scribd
Upload
234 views18 pages

IVEM Inverter User Guide

The document outlines the communication setup between lithium batteries and inverters, detailing the connection process, configuration steps, and troubleshooting notes. It specifies the importance of correct wiring and the need for communication cables to establish a link between the battery management system (BMS) and the inverter. Additionally, it includes guidelines for parallel connections and error codes related to system malfunctions.

Uploaded by

ntaleedward2
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
234 views18 pages

IVEM Inverter User Guide

The document outlines the communication setup between lithium batteries and inverters, detailing the connection process, configuration steps, and troubleshooting notes. It specifies the importance of correct wiring and the need for communication cables to establish a link between the battery management system (BMS) and the inverter. Additionally, it includes guidelines for parallel connections and error codes related to system malfunctions.

Uploaded by

ntaleedward2
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 18

358-010045-05

Lithium Battery Communication


25
25
25
28
28
30
30
31
Parallel connection quantity up to 12units for 5KVA model（Battery must be connected）
500V

120V-500V

472*372*202mm 494*399*202mm
35

10
PV panels
Wiring System for Inverter

L
L
N
N
PE
PE

Utility
Load

Battery pack
4

500V
Indicates Lithium battery type.

Indicates communication is built between inverter and battery.


If selected, inverter is not allowed to
feed exceeding solar power to grid.
Feeding power
to grid
If selected, inverter is allowed to feed
exceeding solar power to grid.
Lithium Battery Communication 4. Power up lithium battery and inverter. Wait a moment, if the communication is built between them, LCD will
show you “C” icon as below.
It’s allowed to connect lithium battery and build communication only which it has been configured.
Please follow bellow steps to configure communication between lithium battery and inverter.
1. Connect power cables between lithium battery and inverter. Please pay attention to the terminals of positive
and negative. Make sure the positive terminal of battery is connected to the positive terminal of inverter, and
the negative terminal of battery is connected to the negative terminal of inverter.
2. The communication cable is bundled with lithium battery. Both sides are RJ45 port. One port is connected to
the BMS port of inverter and another one is connected to the COMM port of lithium battery.

5. Roll LCD real time information pages by pressing “UP” or “DOWN” button, as below page, you can see
the parameters of SOC and battery pack units in the communication system.

BMS BAT+ BAT-

This page means SOC is 88% and battery pack units are 6.

NOTE 1:

NOTE 2: Under parallel operation modes, battery must be connected with inverters.
NOTE 3: Before starting up inverters, please connect all N wires of AC output together.

3. Configure battery type to “Lib” in LCD setting No. 08.

And then LCD will show you “Li” icon.


NOTE:Before starting up inverters, please connect all N wires of AC output together.
Before starting up inverters, please connect
all N wires of AC output together.
BMS firmware
50 Upgrade the firmware of BMS.
version is not matched.
BMS doesn’t allow Inverter will stop charging battery
51
inverter to charge battery. automatically.
BMS doesn’t allow inverter Inverter will stop discharging battery
52
to discharge battery. automatically.
BMS require inverter to Inverter will charge battery
53
charge battery. automatically.
BMS detect something If the code is keeping for long time,
54~65
wrongs happened. please contact with your installer.
1. Please check AC input and output wires are connected correctly.
The AC input and output wires 2. If this error happens during parallel installation, please check wires
27 are inversely connected connection. If they are connected correctly, please funish parallel installation
first, and then restart inverters.
3. If the problem remains, please contact your installer.

1. Please check if single unit is installed to parallel system.


2. If this error happens during parallel installation, please check wires
Single unit is installed to parallel connectiotn. If they are connected correctly, please funish parallel installation
28
system first, and then restart inverters.
3. If the problem remains, please contact your installer.

32

You might also like