Scribd
Upload
4 views

Technical specifications for CO

The document outlines the technical specifications for a Carbon Monoxide and Carbon Dioxide Analyzer, detailing requirements such as measurement ranges, output signals, and operating conditions. It emphasizes the need for calibration, installation protocols, and training for operational staff, along with warranty and maintenance cost considerations. Additional specifications include data logging capabilities, power requirements, and special features for portability.

Uploaded by

chaminda nayanajith
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
4 views

Technical specifications for CO

The document outlines the technical specifications for a Carbon Monoxide and Carbon Dioxide Analyzer, detailing requirements such as measurement ranges, output signals, and operating conditions. It emphasizes the need for calibration, installation protocols, and training for operational staff, along with warranty and maintenance cost considerations. Additional specifications include data logging capabilities, power requirements, and special features for portability.

Uploaded by

chaminda nayanajith
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Technical specifications for Ozone (CO/CO2) Analyzer

Description Specifications

01 Requirement To measure Carbon monoxide and carbon dioxide


. concentration in ambient air

02 Principle NDIR (CO analyzer integrated with IR sensor also accepted)


.

03 Approvals All approvals obtained from USEPA/EN or others should be


. mentioned

04 Brand Name Should be Specify


.

05 Model Should be Specify


.

06 Country of Manufacture Should be Specify


.

07 Country of Origin Should be Specify


.

08 Year of manufacture Should be Specify


.

09 Brand Should be Specify


.

10 Measuring Range Auto-ranging or User selectable multi ranges between 0-


. 200,000 ppb for CO
0-2,000,000 ppb for CO2

11 Concentration Units ppm/ppb or μgm-3 or both


.

12 Linearity < ± 1% of full scale


.

13 Minimum Detectable ≤ 40 ppb


. Limit

14 Response time 60 seconds to 95%


.
15 Output signal RS232/RS422 interface or USB/TCP/IP and/or other
. required communication ports for sharing between analyses
and computers for data, status, control and network
communication and etc.

16 Data Logging facility and  Averaging data for 1, 8, or 24 hours should be available
. transfer for at least 1 year duration.
 Any software required for data transferring and reporting
should be provided.

17 Power Requirement The analyzer should operate at an operating voltage of 230


. volts ± 10 volts AC and 50 Hz + 3%.
If the analyzer has the option with rechargeable battery
operation for uninterrupted operation for 10m hours
duration after the single charge is preferable.

18 Operating conditions The analyzer must function properly in Sri Lankan


. conditions without any defect between 050C - 40C ambient
temperature, and 10 - 95% relative humidity.

19 Special features Should be portable design for field operation.


.

20 Installation and operation  The supplier must specify the installation operating protocol
. and the protocol should be submitted to ITI with the
quotation.
 The installation protocol must include at least full installation,
qualification/performance verification and on-site
familiarization.
 During commissioning the supplier should demonstrate
the CO/CO2 analyzer performance by field operation.

21 Calibration Calibration system should be provided along with the


. analyzer. NIST or any other certification for calibration
system should be provided.

22 Accessories and other  Additional accessories needed for the analyzer


. items  Repair tool kit
 Operation and maintenance manuals,
 Any replaceable parts (Batteries, Power cords, Sensors
etc)
 Rack/ cabinet/ Box or any other system for easy and safe
transportation
 Accessories need for calibration (Pumps, Calibration gas
Etc)

23 Performance/Training  The Supplier shall provide operational & maintenance


hands-on local training for operating staff in Sri Lanka at
the supplier's cost and shall submit a complete set of
training materials to the Purchaser prior to the conduct of
the training program.
 The performance of the analyzer specification should be
demonstrated after hands-on training.

24 Warranty  2 years comprehensive manufacturer warranty should be


provided.
 The supplier must specify the equipment parts covered under
the warranty which are not covered under the warranty with
reasons.
 If in case, the instrument is in out of order during the
warranty period, the supplier should provide an extended
warranty considering this time period.

23 Maintenance cost.  Maintenance cost for two years after warranty should be
. provided.

You might also like