General Multiple choose Question Saudi Aramco

 Which is the correct procedure to de energized an electrical circuit. select the best
answer
 Lock, Tag, clear And try
 Lock, Tag, try And clear
 Tag, Lock, clear And try
 Tag, Lock, try And clear
 When working within one arm’s length of electrical equipment you should not wear
which of the following. Select all that apply.
 Safety Glass
 Jewellery
 Glasses with metal frames
 Rings
 Why should the electrical panel board breaker list be regularly updated? Select the
best answer.
 For thorough record keeping
 To easy locking and tagging for regularly maintenance
 To determine when breakers need to be replaced
 For isolation in case of emergency
 When should Ground Fault circuit interruption be used? Select all the apply?
 In dump area
 When using temporary work
 At all times
 When using portable electrical tool
 What is the correct slope at which ladder6 should be use?
 3m horizontal for 1m vertical
 1m horizontal for 3m vertical
 4m horizontal for 1m vertical
 You are performing high voltage work and are wearing all PPE. What after that may
be required to provide to insulation from energized or grounded.
 Conducting Mets
 Non-conducting Mats
 Conducting Blankets
 Non-conducting Blankets
 What parts make up a personal fall arrest system?
 Harness
 Connectors
 Parachute
 Lanyard
 Who can complete the field inspection and tagging of a special scaffold taller than 6m
or 20 ft. select all items that apply
 Any contractor employee
 Scaffold inspector
 Scaffold supervisor
 Any Saudi Aramco employ
 You have to work on a fixed elevated work surface. What should you do before
working?
 Test by exceeding the maximum weight
 Look for and guard all floor openings
 Inspect grating clips for security
 Test using a personal fall arrest system
 You are about to raise an elevating work platform. What should you do? Select all
items that apply.
 Ensure you and tools carry are within weight limits
 Connect the lanyard of your harness to the anchor point
 Retract the outriggers so that the lift is easily moved
 Check that the gate or chain is securely closed
 What precaution should you take when using a personal fall arrest system? Select all
items that apply.
 Do not use it to hoist materials
 Protect it from cuts or abrasive
 Wash is at least once a weak
 Do not use after it stop a fall
 Who can erect scaffolding shorten than 12.2m (40ft)? Select all items that apply.
 Qualified scaffold erectors
 Any team of experienced contractors
 Approved specialist scaffolding erectors
 Any team of Saudi Aramco employees
 What must you do before you rely on a fall arrest system? Select all items that apply.
 Inspect that fall arrest system
 Check for inspection sticker
 Remove defective components
 Attached a weight and let it fall
 You are going to operate an elevating work platform, what safety precaution must be
taken? Select all items that apply.
 You must wear full body harness and anchor it to the lift
 The elevating work platform must have a current SA inspection sticker
 You must be qualified to operate the elevating work platform
 Who should inspect cranes prior to their use? Select the best answer.
 Shift supervisor
 Contractor
 Engineers
 Operations
 When the crane is travelling how should the boom be positioned? Select the best
answer.
 Lowered with the hook free
 Raised with the hook free
 Raised with the hook secure
 Lowered with the hook secure
 Crane lift shall not be allowed at wind speed above…….unless otherwise specified the
manufacturer. Select the best answer.
 10 km/h (6mph)
 32 km/h (20mph)
 20 km/h (13mph)
 64 km/h ( 40mph)
 Where should the signal man stand relative to the crane?
 To the side of the crane operator
 In the crane operator direct line of sight
 In front of the load
 In front of the crane
 How should personal be transferred using crane? Select the best answer.
 Slings
 Ropes
 Mobile scaffold
 Man baskets
 Which of the following should have an inspection sticker before a crane lift? Select all
that apply.
 The rigging equipment
 The lode
 The outrigger mates
 The cranes
 Which of the following lifts required critical lift plans? Select all that apply.
 Operation inside a warehouse
 Operation inside refinery
 Lifting a load that weight 20 tons
 Lifting a large load that requires 3 cranes
 When lowering a load into an excavation pit 5 meters deep, what is the max distance
from the pit should the crane be positioned? Select the best answer.
 3 meters
 It doesn’t matter
 5 meters
 10 meters
 Which of the following cylinders must use flashback arrestor? Select all that apply.
 Acetylene
 Nitrogen
 02
 H2s
 What should know the weight of before beginning a lift?
 The rigging equipment
 The crane
 The lifting bar
 The load
 What is the minimum safe distance between overhead power line up to 50,000 V
(volts) and any part of a crane? Select the best Answer.
 1.8 m (6ft)
 2m (7ft)
 3m (10ft)
 6m (20ft)
 Above what weight are critical lift plan required?
 20 tons
 30 tons
 40 tons
 50 tons
 Who is allowed to operate crane? Select all that apply.
 Trainer under direct supervisor of a qualified trainer
 All contractor
 Trainer under direct supervisor of a certified crane operator
 Saudi Aramco certified operators
 Crane suspended man basket operations shall not be allowed? Select the best
answer.
 30 km/h (18mph )
 25 km/h (15mph )
 15 km/h (10mph)
 32 km/h (19mph)
 How many minimum safety rules are there in safety handbook?
 15
 01
 22
 33
 What number should you call when reporting an incident from a Saudi Aramco
phone?
 03-872-0110
 03-673-0110
 110
 01-285-0110
 Which of the following is not required when reporting an emergency?
 Your badge number
 Your age
 Your name
 Victim number
 When reporting emergency. You should? Select all that apply.
 Remain on the telephone line
 Describe the location of the incident
 Call your supervisor
 Describe the incident
 How many elements does the loss prevention policy contain?
 12
 13
 11
 10
 Who responsible for investigating injuries, spills, and other incident and promptly
provide corrective action. Select all that apply.
 Team leader
 Outside operator
 Contractor
 Supervisor
 Who is responsible to comply with all applicable rules, standards, and safe work
practices?
 Contractor only
 Employee only
 Manager only
 All employee
 Which of following is not a responsibility of an employee?
 Report injuries, spill, unsafe conditions, near misses, and incident immediately
 Maintain knowledge of safety requirement
 Communicate safety rules and standards to contractors
 Maintain facility emergency plans and conduct regular emergency drills.
 What must an employee report immediately? Select all that apply.
 Spill
 Near miss
 Injuries
 Incident
 Who is responsible for operating Saudi Aramco equipment only with proper Saudi
Aramco certification?
 Supervisor
 Employee
 Contractor
 Who should report an all spill?
 Your manager
 Your supervisor
 Your safety coordinator
 When should you report a vehicle accident?
 Immediately
 After you talked to the traffic police
 The following day
 What should you do when going up a stairway?
 Use the handrail but take as many steps at a time as you can
 Always use the handrail and take a only one step at a time
 Use the handrail only as needed
 Take only one step at a time use the handrail when necessary
 What should you do wherever safety device is broken?
 Notify all affected parties
 Notify only supervisor
 Notify the supervisor and affected parties
 Repair the device
 Which of the following should be in place and functional when operating machinery
and electrical switch …?
 Fire watcher
 Fire extinguisher
 Block valves
 Safety guards
 At what height should you use approved fall arrest measure?
 Between .8 to 1.8 M
 Greater than 1.8 M
 1.8 M
 Less than 1.8 M
 What must the receiver keep at the work site?
 The joint inspection report
 The gas testing result
 The name of work permit issuer
 The active work permit
 What is the normal duration of the work permit?
 One shift
 One day
 One job
 One week
 Who initiates the request for a work permit?
 The work site contractor
 The work permits issuer
 The work site Forman
 The work permit receiver
 Who must participate in a site inspection?
 The work permits issuer and receiver
 The operation supervisor and permit receiver
 The work permit issuer and contractor
 The safety coordinator and permit issuer
 What is the purpose of a cold work permit?
 To control work activities that could case fire
 To control activities that could not cause a explosion
 To control work activities that could cause an explosion
 To control work activities that could not cause an injury to workers
 Into a 2 m deep sump pit to tighten a bolt with hand tool, which work permit do you
need?
 Release and confined space work permit
 Hot work ,cold work and release work permit
 Confined space work permit and cold work permit
 Confined space work permit and hot work permit
 Who is mainly responsible for identifying hazards and defining precaution on the
work permit?
 Gas tester
 Loss prevention
 The receiver
 The issuer
 Who decide which type of permit required?
 The receiver
 Gas tester
 The issuer
 Loss prevention
 How is business to be conducted in Saudi Aramco as per loss prevention policy?
 Preserving assets
 With incidents
 Preserving life
 Without any incident or accident
 How many safety precautions are entered in the work permits to control the hazards?
 Maximum
 Minimum
 Zero
 100
 When the hazards in a work permit process are identified?
 After issue of work permit
 Once a week
 Before issue the work permit
 Identified the name classified for a gasoline service station?
 Service area
 Restricted area
 Non-restricted area
 Hazardous area
 Which gas is generated during spray painting work or present in engine exhaust
fumes?
 H2s
 Carbon monoxide
 Sulphur dioxide
 Calcium oxide
 When a gas is said to be toxic it means?
 It can burn
 It can sink
 It can explode
 It can poison
 What is threshold limit value (TLV) of a gas?
 The level at which a gas become toxic
 The level which a worker has great risk
 The level at which you can safely be exposed day after day
 The level at which a gas burn
 Which hazard are you checking when you take a gas test sample of the air you
breathe?
 Lower exposure limits
 Nitrogen level
 Oxygen level
 Upper lower limits
 Below which LEL level can a hot work permit issued?
 O%
 25%
 50%
 100%
 When should a toxic accumulate in a tank if a gas is lighter than air?
 In the middle
 At the top
 One the side
 At the bottom
 What should you do if your mentor asked you to enter a vessel that was emption?
 Wear the proper PPE
 Enter if a watchman is present
 Ask for a confined space entry permit to be issued before entering the vessel
 Where should you go if you’re warned about toxic gas leak?
 Supervisor office
 Home
 Downwind
 Upwind
 Which is an energy source that would about a toxic gas leak?
 Load
 Light
 Hydraulic
 Gravity
 Which is a method of isolating a section of pipeline for LOTO?
 Removing a fuse
 Closing a circuit breaker
 Closing a valves
 What is the first step of the LOTO procedure?
 Stop associated equipment
 Activate all equipment
 Maintain all associated equipment
 Remove all associated equipment

Which certified rigger can approve a critical lift plan per GI 7.028?

 Rigger III
 Rigger I
 Rigger II
 None of above

How long should the appointed fire watch remain at the site of hot works after the work
has stopped?

 10 minutes
 20 minutes
 30 minutes
 15 minutes
The proper first aid treatment if someone comes in contact with chemical is to first call for
emergency medical assistance and then?

 Wash the affected area

 Don’t touch anything until medical personnel arrive
 Apply a cream to the affected area
 None of the above

Controlling sources of heat and sources of fuel are two general categories of what?

 Fire prevention method

 Firefighting method
 Chemical reaction method
 Fire extinguisher method

If you must exit through smoke, you should?

 Stay low by crawling on your hand and knee

 Cover your mouth and nose and quickly escape
 Wait for help
 None of the above

At which decibel level is mandatory hearing protection required?

 80
 85
 90
 None of above

What should you do if you discover a rung missing near the top of the ladder you are
about to use?

 Use the ladder but make sure you are careful when going over the missing rung
 Stop using the ladder and report the defect immediately
 Flip the ladder so the missing rung stay closer to the ground
 Use the ladder but make sure a colleague holds the ladder while you are on it

Which of the following lift is considered as a critical lift as per Aramco standards?

 Lifting a 39 tons vessel using mobile crane

 Lifting a 10 tons vessel during night time
 Lifting e meter away from the excavation
 Lift a portable cabin

Ladder safety required?

  Only small tools should be carried in your hand when climbing a ladder
 Extension ladder don’t have to be tied-off to a secure structure
 Only two men can be on the ladder at the same time
 Person climbing on ladder must maintain 3 point of contact

Wire rope sling shall have a permanent manufacture’s label showing?

 Capacity (SWL) in tons

 Manufacture’s name, trademark, or logo
 Serial number by the manufacture’s
 All of the above

One of three basic elements of fire is present, what must occur to ignite a fire?

 The element must be contained

 A flam or spark must be present
 The element must be mixed equally
 A chemical reaction must take place.

The best way for a supervisor to improve safety in the workplace is to?

 Award certificates to staff that do not have accidents

 Publish articles about health and safety, in the company newsletter
 Give incentives to staff that have low absenteeism rates
 Involve staff in hazard spotting

Report to avoid reoccurrence?

 Unsafe conditions
 Unsafe act
 Near misses
 All of above

As par international standards full body harness shall be worn to prevent falls greater
than?

 1m (3.33 feet)
 1.5m (5 feet)
 1.8m (6 feet)
 2.2m (7.22 Feet)

What is the meaning of MVA?

 Motor vehicle accident

 Management vehicle accident
 Motor vehicle association
  Motor violation accident

Who is allowed to inspect scaffolding of more than 6 meters height?

 Scaffolding foremen
 Scaffolding supervisor
 Scaffolding inspector
 Safety officer

What are the two main causes of incident in the workplace?

 Unsafe act and unsafe people

 Unsafe people and unsafe machines
 Unsafe condition and unsafe machines
 Unsafe acts and unsafe conditions

When grinding a piece of metal with a portable power grinder, the type of personal
equipment required is?

 Safety glasses only

 Safety glasses and dust mask combination
 Face shield only
 Safety glasses and face shield combination

In an event of fire, the PRC emergency hotline for fire department is?

 911
 999
 119
 199

What are the speed limits on construction site?

 40 km
 30 km
 10 km
 20 km

What is used to control the suspended load?

 Slings
 Tag lines
 Guys
 Shackle
The lighting system failed, causing a short circuit, which resulted in a fire. What class of
fire would this be?

 Class A
 Class B
 Class C
 Class D

If you observed a hazard that threatens personal and or equipment safety, you immediate
action is?

 Stop the work

 Close my eyes
 Look for supervisor immediately and report for corrective action
 Call the PMT HSE engineer

If someone is injured on your job site, a written preliminary incident report must be
submitted to the PMT office. Do within period of time.

 12 Hrs.
 24 Hrs.
 48 Hrs.
 72 Hrs.

Anchorage point shall be fixed and able to support a load at least?

 5000 pounds
 4000 pounds
 5000 kilograms
 4000 kilograms

In Aramco standard what type of rigger can lift 15 tons weight?

 Rigging supervisor
 Rigging foreman
 Rigger II
 Rigger III

The ratio of vertical to horizontal spacing for a straight or extension ladder is?

 1 to 1
 2 to 1
 3 to 1
 4 to 1

If you see a barricade fallen down along the road, what is the best thing to do?
  Informed to contractor HSE manager
 Wait for someone else to install back the barricade
 Installed the barricade as it was
 Leave it like it is

Which of the following would be classified as a class “B” fire?

 A fire involving ordinary combustibles

 A fire involving flammable liquids
 A fire involving combustibles metals
 A fire involving live electrical equipment

Burning scrap wood is considered what class of fire?

 Class A
 Class B
 Class C
 Class D

You have noticed unacceptable waste level in your area what you will do?

 Report to supervisor
 Report to HSE Manager
 Instruct to concerned personal to barricade the area and cover with tarpaulin sheet
 All of above

The most common way for a harmful or chemical substance to enter the body is?

 Ingestion
 Injection
 Absorption
 Inhalation

Rigging hardware inspection procedure should be?

 Requested by supervisor
 Systematic and non-compromising
 Whenever sling to be stored
 All of the above

If you see a45 gallon of chemical on the site, it should be on?

 Ply board
 Pallet
 Drip tray
 Sand ground
When a worker is one mobile elevated work platform (MEWP) or man-lift, in what
instance he should be clip off?

 Only when it’s moving

 If the gate is open
 When it is in the raised position
 All of the above

It is a component consisting of flexible line for connection to an anchorage at one end to

hang vertically or that connects to the anchorage at both ends to stretch horizontally?

 Lanyard
 Anchorage
 Spigot
 Lifeline

If you place your hand inside the confined space, it is considered as a confined space
entry?

 True
 False

If you noticed moving heavy equipment working in your area without flagman, what will
you do?

 Let it pass you

 Stay away from the equipment
 Call the safety manager
 Stop the moving equipment

Crane operation must be stopped when the wind speed is over 32 Kph?

 True
 False

Hand held power tools such as drill and grinders may be locked-on if the job is going to
take a long period of time of accomplish?

 True
 False

Low voltage means low hazard?

 True
 false
It the lowest temperature at which a chemical or flammable material can vaporize and
have the potential to ignite and produce fire?

 LEL
 MSDS
 Flash point
 UEL

Symptoms of heat cramps?

 Pain in muscles, arms, calves, abdomen, and/or back

 Not sweating
 Low grade fever
 Unconsciousness

All working levels shall be fully planked. Working levels shall be at least wide?

 1 plank
 2 plank
 3 plank
 None of the above

You have two lanyards and only one lanyard is hooked to the anchorage point. It’s called
tie off?

 50% tie off

 200% tie off
 110% tie off
 100% tie off

RPM rating of the grinding disc/wheel must be than the rating of the grinder?

 Less
 More
 Equal
 All of the above

What scaffold you will put on an inaccessible crash deck (to show it has been inspected).

 Green tag
 Red tag
 Yellow tag
 None of above

You are up on a roof that is flat. How can make sure that the workers will not fall over the
side of the roof?
  Use red and white tape to mark out the edge
 Tell the workers or supervisor to installed a warning sing
 Use a guard rail system with toe boards to protect the sides
 Get someone to watch the workers while they are on the roof and when they get
closed to the edge shout

Holes may be drilled into sides of hard hats to provide cross ventilation air flowing during
very hot weather?

 True
 False