Mini Condensate Pumps

Sauermann
SI30 & SI33
The Sauermann SI30 & SI33 pumps are specifically designed to be installed on:
• Wall mounted units • Fan coil unit
• Ceiling suspended units • Ducted units

These pumps are a two piece kit with the pump and float detection sensor interconnected via the click fit sensor cable and
suitable drain hose, depending on the installation requirements.

Features
• 90°C Thermal protection • 20dBA at 1m - SI30
• 34dBA at 1m - SI33

Cat. No. Model No. Description Nominal Flow Rate Max Suction Lift Max Discharge Head
2701913 SI-30 20l/hr 3m 10m
Condensate Pump
2701914 SI-33 30l/hr 4m 13m

Delta Pack
The Sauermann Delta Pack is a convenient complete ready to install ‘quick fit kit’ for wall mounted units. The pump is
mounted on a anti-vibration bracket inside the trunking elbow, in line with the drain reservoir. Suitable for either side of the
unit. The kit comes with pump & integrated detection, anti-vibrating reversible mounting bracket, electrical quick mount
power cable, 15mm connecting rubber drain hose, trunking and rubber joint.

Features
• 90°C Thermal protection

Cat. No. Model No. Description Nominal Flow Rate Max Discharge Head
2701921 DELTA PACK Condensate Pump Kit 20l/hr 10m

Si10
The Sauermann Si10 is a monobloc pump with integrated transparent float reservoir which is designed for easy
maintenance. Covers a large range of capacity up to 20kW. Drain safe device facilitates connection to the discharge pipe.
The pump is silent at 22dbA and the wall bracket is designed to reduce vibration.

• Wall split systems • Floor mounted units

• Ceiling suspended units • Ducted units
• Fan coil units

Pump also comes with quick fit electrical power cable, 15mm & 35mm rubber inlet connecting drain hose and a 4mm vent tube.

Features
• 90°C Thermal protection

Cat. No. Model No. Description Nominal Flow Rate Max Discharge Head
2701872 SI-10 Condensate Pump 20l/hr 10m

360 | Section 7
www.actrol.com.au Subject to change without notice | © 2017 Actrol Parts Pty Ltd ABN: 93 142 654 564
 Mini Condensate Pumps
Aspen
Mini & Maxi Orange
The Aspen Mini Orange & Maxi Orange pumps are designed to be installed:

• Above the false ceiling where possible • Behind wall mounted evaporators
• In plastic conduit

Connecting the drain hose to the reservoir and placing the pump drive unit within the evaporator, condensate water can
be pumped away to a suitable drain. Within the Orange kit there are two reservoirs to choose from, which must sit flat and
horizontal. One allows you to connect directly to the drain hose of the evaporator and the second reservoir can be placed
directly into a condensate tray.

Cat. No. Part No. Description Max Flow Rate Max Discharge Head
2702633 FP2212 Mini Orange Condensate Pump 12l/hr 10m
2702779 FP2210 Maxi Orange Condensate Pump 35l/hr 15m

Mini & Maxi Lime

The Aspen Mini Lime & Maxi Lime pumps are completely unique, in both their design and installation advantages.
The pumps are clipped directly onto the reservoir so there is minimal suction lift. By connecting the drain hose to the
reservoir of the pump unit, condensate water can be pumped away to a suitable drain.The pumps fit securely into a
specifically designed elbow that holds them horizontally to ensure reliable operation. The pump and elbow are reversible
therefore they can be installed easily on either side of an evaporator unit.

Cat. No. Part No. Description Max Flow Rate Max Discharge Head
2701889 FP3312 Mini Lime Condensate Pump 12l/hr 10m
2701890 FP2213 Maxi Lime Condensate Pump 35l/hr 15m

Mini Blanc
Designed to be fitted below the indoor unit, the Mini Blanc offers an extremely easy to install mini pump for all wall and
ceiling suspended indoor units. Suitable for both commercial and domestic installations, the quick fit pump is simply
screwed to the wall. It is easy to access therefore low maintenance. The Mini Blanc is ultra quiet in operation as well as
discreet, with a slim profile of 55mm from the wall.

Cat. No. Part No. Description Max Flow Rate Max Discharge Head
2705826 FP1080 Mini Blanc Condensate Pump 12l/hr 10m

Mini Aqua
The Mini Aqua has been designed to give the installation flexibility, where the latest generation of A/C units are becoming
even smaller.

The Mini Aqua is designed to be installed:

• Within wall mounted evaporators • In plastic conduit

By connecting the drain hose to the reservoir and placing the pump drive unit within the evaporator or conduit, condensate
water can be pumped to a height of 8 metres. Using the proven functionality of Aspen’s other mini pumps, the Mini Aqua is
also incredibly slim in size. Measuring only 28mm in height and 28mm in depth, it is one of the smallest condensate pumps
in the world.

Cat. No. Part No. Description Max Flow Rate Max Discharge Head
2705825 FP2406 Mini Aqua Condensate Pump 12l/hr 10m

Section 7 | 361
© 2017 Actrol Parts Pty Ltd ABN: 93 142 654 564 | Subject to change without notice www.actrol.com.au
 Mini Condensate Pumps
Blue Diamond
The Blue Diamond is a heavy duty rotary diaphragm condensate pump. The rubber construction of the rotary diaphragm
copes with sludge, slime, grit and even running dry. The pump is whisper quiet and yet has high flow rates. The pump
comes complete with a reservoir sensor. This pump is ideal for larger and/or problematic installations.

Features
• Self priming
• Ultra reliable
• Reduced service costs
• Slimline
• Blue Diamond has the performance to overcome installation difficulties - just plug and play, fit and forget.
• Kit with in & out tubing & connections, anti vibration feet & mountings, integral volt free alarm module & 3 core power cord (2m)
• Connect the drip tray to the pump reservoir. The hi-low solid state level sensors automatically switch the pump on/off to
remove the condensate.
• The alarm shuts off the A/C in fault mode and restarts the A/C when the condensate has cleared.

Cat. No. Part No. Description Max Flow Rate Max Head Max Suction Lift
1602605 MegaBlue 50l/hr 20m 7m
1602606 MaxiBlue Condensate Pump 14l/hr 8m 8m
1602607 MiniBlue 8l/hr 8m 5m

Little Giant
EC-400 Condensate Pump
Removes condensate from wall or ceiling mounted air conditioners. The EC-400 consists of three components: control unit,
detection reservoir and pump. All three components can be placed inside the air handler, or any of the three can be placed
outside the air handler. The pump and control unit can be placed up to one metre above the air handler. A three position
float detection system assures reliable On, Off and Safety Alarm functions. The EC-400 is suitable for use with split air
conditioners up to 10 kW.

Cat. No. Part No. Description Max Flow Max Head Max Suction Lift
1602531 EC-400 Condensate Pump 18l/h 14m 1m

mini blanc
condensate removal pump
ultr
quic a
fit!
k

The ‘ultra quick fit’ Mini Blanc is designed to be fitted beneath high
wall indoor units and offers easy access for future maintenance.

12L/h max. flow KEY FEATURES SUITABILITY

10m max. rec. head • Extra quick to fit • Up to 16kW / 54,000Btu/h

(flow rate 6L/h) • Compact & discreet • High wall mini split systems
• Clear removable reservoir Perfect for... Domestic use –
21dB(A) • Ultra quiet operation where easy maintenance is key

a
Takek!
loo No job is the same! Find the right pump
for the job at aspenpumps.com
mini orange® mini aqua® silent+ mini lime

Propipe Actrol Diary Ad 99x210.indd 1 14/12/2016 09:57

 Mini Condensate Pumps
Refco
Gobi
The Gobi is a condensate discharge module designed to be fitted below modern wall mounted air conditioners.

Features
• Electronic Energy Control System (EECS) with alarm circuit • Soft start with EECS
• Quick, simple trouble free installation • Aesthetic design blends in naturally into its surroundings
• Thermal protection • Amazingly quiet
• Built-in non-return valves • Fits all high-wall-mount air conditioners
• CE and UL marked

Specifications
• Power supply: 120/240 V,50/60 Hz auto sensing • Power consumption: 16W maximum, 0.25A when idle
• Alarm relay: 5A, 30 VDC, 250 VAC break on fault • Capacity: 12l/h maximum
• Maximum discharge head: 20m vertical, 100m horizontal • Maximum suction head: 1m
• Ambient temperature: 0C - 40C • Material: Flame retardant ABS - UL94 5 VA
• Discharge tube: 6 mm ID • Dimensions: 286 x 61 x 53 mm

Cat. No. Part No. Description Max Flow Rate Max Discharge Head
1602608 4678538 Gobi Condensate Pump 12l/hr 15m

Karoo
The Karoo drain pan pump is a submersible condensate removal pump designed to automatically remove condensate water
from refrigerated cases, dehumidifiers, fan coils and air conditioning systems.

Features
• Electronic Energy Control System (EECS) with alarm circuit • Soft start with “EECS”
• CE and UL marked • Submersible
• Amazingly quiet • Powerful and compact
• Filter and non-return valves built in • No mechanical floats to stick
• All electrical components safely encapsulated against moisture ingress

Specifications
• CE & UL markedCapacity: 12l/h maximum
• Maximum suction head: 1m
• Ambient temp: 0C - 40C
• Material: Flame retardant ABS - UL94 5 VA
• Discharge tube: 6mm ID
• Dimensions: 160 x 43 x 34 mm
• CE & UL markedPower supply: 120/240 V, 50/60 Hz Auto sensing
• Maximum discharge head: 20m vertical, 100m horizontal
• CE & UL markedPower consumption: 16W maximum, 0.25W when idle
• CE & UL markedAlarm relay: 5A, 30VDC, 250VAC break on fault

Cat. No. Part No. Description Max Flow Rate Max Discharge Head
1602609 4678512 Karoo Condensate Pump 12l/hr 6m

Section 7 | 363
© 2017 Actrol Parts Pty Ltd ABN: 93 142 654 564 | Subject to change without notice www.actrol.com.au
 Peristaltic Pumps
Sauermann
PE5200
The Sauermann PE5200 pump is suitable for units up to 8kW. Specifically designed for the following:

• Wall mounted air conditioners • Ceiling mounted units • Ducted air conditioning units

This model is a compact in size and operates via a float detector. It features a high 12m discharge head height and is very
quiet in operation. It is IP65 rated. It offers a high level NC alarm contact. Replacement tubes and heads make maintenance/
replacement easy (no need to re-wire the base unit – simple fit and clip in the new motor) Supplied with an easy fix wall
bracket.

Cat. No. Model No. Description Nom. Flow Rate Max Suction Lift Max Discharge Head
2701878 PE-5200 Peristaltic Condensate Pump 6l/hr 2m 12m

PE5100
The Sauermann PE5100 pump is suitable for units up to 8kW. Specifically designed for the following:

• Wall mounted air conditioners • Ceiling mounted units • Ducted air conditioning units

This model is a compact in size and operates of via two sensors which measures 6C delta T temperature differential.
It features a high 12m discharge head height and is very quiet in operation. It is IP65 rated. Replacement tubes and heads
make maintenance / replacement easy (no need to re-wire the base unit – simple fit and clip in the new motor) Supplied
with an easy fix wall bracket.

Cat. No. Model No. Description Nom.Flow Rate Max Suction Lift Max Discharge Head
2701885 PE-5100 Peristaltic Condensate Pump 6l/hr 2m 12m

PE5000
The Sauermann PE5000 pump is suitable for units up to 8kW. Specifically designed for the following:

• Wall mounted air conditioners • Ceiling mounted units • Ducted air conditioning units

This model is a compact in size and operates of a cooling signal. It features a high 12m discharge head height and is very
quiet in operation. It is IP65 rated. Replacement tubes and heads make maintenance / replacement easy (no need to re-wire
the base unit – simple fit and clip in the new motor) Supplied with an easy fix wall bracket.

Cat. No. Model No. Description Nom.Flow Rate Max Suction Lift Max Discharge Head
2701886 PE-5000 Peristaltic Condensate Pump 6l/hr 2m 12m

PE6250
The Sauermann PE6250 pump is suitable for the following;
• Refrigerated display and cold store cabinets • Evaporators
• Ceiling mounted units • Ducted air conditioning units

This model offers a high flow rate of 25 l/h and operates float control switch and is IP65 rated. It features a high 10m
discharge head height and maximum 2m suction lift. Replacement tubes make maintenance easy. Supplied with an easy fix
wall bracket.

Cat. No. Model No. Description Nom. Flow Rate Max Suction Lift Max Discharge Head
2701879 PE-6250 Peristaltic Condensate Pump 25l/hr 2m 10m

364 | Section 7
www.actrol.com.au Subject to change without notice | © 2017 Actrol Parts Pty Ltd ABN: 93 142 654 564
 Peristaltic Pumps
Aspen
Universal Peristaltic
The Universal peristaltic pump operates with two temperature sensors. These allow the pump to detect and be triggered by
a change in air temperature, making this pump suitable for many applications.

The Universal pump is a peristaltic rotary type - which means that it is quiet in operation, very reliable and will run dry without
fear of damage or embarrassing noise. Unlike other pumps using either mechanical or electrical conductivity sensors, the
Universal does not suffer from corrosion or contamination problems.

Features
• Senses 5C differential across the evaporating coil • Operates only on cooling • Self-priming lifts 3 metres
• 12 metres discharge head • 3 minute timer overrun • No siphoning back
• No loud sound from dry running • Manual test switch • Fire retardant plastics
• Pumps water, fibrously contaminated water and air • Push-in plug • Wall-mounted bracket
• Only requires live/neutral supply and 2 sensors either side of the evaporating coil – one ‘air on’ and one ‘air off’

Specifications
• Dimensions: 115mm(H) x 135mm(W) x 77mm(D) • Pump rating: 0.2A, 230V AC • Connecting cable: 3 metres
• Inlet /outlet size: 6mm

Cat. No. Part No. Description Max Flow Rate Max Discharge Head
2705828 FP2082 Universal Peristalic Condensate Pump 6.25l/hr 12m

Tank Pumps
Little Giant
VC Series
For removal of condensate from air conditioners, condensing boilers, refrigerated display cabinets, and dehumidifiers.

Features
• Fully automatic; start, stop, safety switch • Operating point: 4 m: 70 l/h • Thermally protected motor
• Check valve outlet: 9.5 mm, for 9.5 mm ID tubing • IP 20 • CE. TUV and BAU approved
1
• ⁄30 HP motor • ABS tank, motor cover, and volute • Stainless steel shaft

VCMA-20S
Features
• 2.0L tank capacity • Removable 9.5 mm barbed check valve • 3 inlet drain holes
Capacity: l/m
Cat. No. Part No. Description 0.5m Water 1m Water 1.5m Water 3m Water 4.3m Water Amps
Head Head Head Head Head
1602532 VCMA-20S Condensate Pump 4.8 4.7 4.5 3.3 0 0.6

VCC-20S
Features
• Low profile for limited space applications • Removable 9.5 mm barbed check valve • 1.0L tank capacity
Capacity: l/m
0.5m 1.5m 4.3m
Cat. No. Part No. Description 1m Water 3m Water Amps
Water Water Water
Head Head
Head Head Head
1602533 VCC-20-S Condensate Pump 4.8 4.7 4.5 3.3 0 0.6

Section 7 | 365
© 2017 Actrol Parts Pty Ltd ABN: 93 142 654 564 | Subject to change without notice www.actrol.com.au
 Tank Pumps
Sauermann
SI60
The Sauermann SI60 is a monbloc pump with built in tank. It is an ergonomic and compact tank pump which offers
condensate inlet on the top or on the front side. The patented detection system is not sensitive to clogging, whatever the
environment. It has a plug in power cord and easily accessible tank and is designed to be installed on floor mounted units,
ceiling suspended units, ducted units and fan coil units.

Features
• 90°C Thermal protection • 38dBA at 1m
Cat. No. Model No. Description Nom. Flow Rate Max Discharge Head Tank Size
2701933 SI-60 Condensate Pump 20l/hr 10m 0.5l

SI82
The Sauermann SI82 pump is specifically designed to be installed on:
• Refrigerated display cabinets • Cold store cabinets • Dehumidifiers
• Ducted units • Multi cassette unit • Column air conditioning units
• Gas condensing boilers

This model is a single piece 2 litre tank unit, and is built to last. It has high performance and tolerates charged, high
temperature and mildly acidic condensates from refrigeration and air conditioning systems. Can be floor mounted attached to
a wall or hung from a ceiling. Easily removable tank and reversible pump, for left or right entry with a quick fit electrical cable.
Features: 105°C Thermal protection
Cat. No. Model No. Description Nom. Flow Rate Max Discharge Head Tank Size
2705832 SI-82 Condensate Pump 500l/hr 5m 2l

SI1805
The Sauermann SI1805 pump has a compact tray and is specifically designed to be installed on:
• Refrigerated display cabinets • Cold store cabinets • Dehumidifiers
• Ducted units • Multi cassette unit • Column air conditioning units
• Gas condensing boilers

This model is a single piece 0.5 litre tank unit, and is built to last. It has high performance and tolerates charged, high
temperature and mildly acidic condensates from refrigeration and air conditioning systems. Can be floor mounted attached to
a wall or hung from a ceiling. Easily removable tank and reversible pump, for left or right entry.
Features: 130°C Thermal protection
Cat. No. Model No. Description Nom. Flow Rate Max Discharge Head Tank Size
2701887 SI-1805 Condensate Pump 500l/hr 5m 0.5l

SI1830
The Sauermann SI1830 pump is an IPX4 rated pump, which has been specifically designed for high resistance acid and
temperature applications but can be installed on:
• Oil condensing boilers • Gas condensing boilers • Gas furnaces
• Refrigerated display cabinets • Cold store cabinets • Evaporators
• Multi cassette unit • Column air conditioning units

This model is a single piece 0.5 litre tank unit, which can be installed internally or externally to the system. It is a semi
submersible design and has a waterproof rating of IPX4. It also has a low sound level and is compact in size.
Features: 120°C Thermal protection
Cat. No. Model No. Description Nom. Flow Rate Max Discharge Head Tank Size
2701920 SI-1830 Condensate Pump 400l/hr 3.7m 0.5l

366 | Section 7
www.actrol.com.au Subject to change without notice | © 2017 Actrol Parts Pty Ltd ABN: 93 142 654 564
 Tank Pumps
Sauermann
SI1822
The Sauermann SI1822 pump has a large volume tank of 3.8 litre it has been specifically designed for large volume and higher
than standard discharge height (up to 5.8m). This model can be used on the following applications:
• Refrigerated display cabinets
• Cold store cabinets • Evaporators • Ducted units
• Multi cassette units • Column air conditioning units • Gas condensing boilers
• Gas furnaces

This model has high performance of up to 380 l/h and can evacuate heavy, charged, high temperature and acidic (pH >3.4)
condensates from refrigeration or air conditioning systems.
Features: 105°C Thermal protection
Cat. No. Model No. Description Nom. Flow Rate Max Discharge Head Tank Size
1602603 SI-1822 Condensate Pump 380l/hr 5.8m 3.8l

SI1850
The Sauermann SI1850 pump has a large volume tank of 3.8 litres and it has been specifically designed for large volume and
higher than standard discharge heights (up to 10m). This model can be used on the following applications;
• Refrigerated display cabinets • Cold store cabinets • Evaporators • Ducted units
• Multi cassette units • Column air conditioning units • Gas condensing boilers
• Gas furnaces

This model has the highest performance of flow and discharge height (100 l/h and 10m respectively) and is designed to
evacuate heavy, charged, high temperature and acidic (pH >3.4) condensates from refrigeration or air conditioning systems.
Features: 135°C Thermal protection
Cat. No. Model No. Description Nom. Flow Rate Max Discharge Head Tank Size
2701877 SI-1850 Condensate Pump 1100l/hr 10m 3.8l

SI93
The Sauermann Si 93 pump is specifically designed for refrigeration applications, such as:
• Refrigerated display cabinets • Cold store cabinets
• Dairy cabinets • This model is ultra flat with a height of 69mm.

Built to last in stainless steel this model features a patented non-chemical anit-biofilm system which helps retard bio-film
growth and assists with reduced site maintenance. Slides easily underneath the refrigerated display cabinet with a minimum
tank profile of 69mm. It also has top, left or right inlets. Comes with universal inlet adapter (32-40-50mm), an easy opening
tank lid and modular pump compartment for ease of maintenance.
Cat. No. Model No. Description Nom. Flow Rate Max Discharge Head Tank Size
1600036 SI-93 Condensate Pump 360 20m 1.6l

OEM Replacement
SI2052
The Sauermann SI2052 pump is maintenance kit, specifically designed for replacing failed OEM centrifugal lifter pumps:
• 2 way and 4 way blow cassette units • Ceiling mounted units • Ducted air conditioning units

This model is a compact unit with a universal mounting bracket, float and standard length electrical cable.
It is capable of pumping a maximum of 70 l/h and has a maximum discharge lift of 0.95m

Cat. No. Model No. Description Nom. Flow Rate Max Discharge Head Max Immersion
Universal OEM Replacement
1602601 SI-2052 70l/hr 0.95m 20mm
Condensate Pump

Section 7 | 367
© 2017 Actrol Parts Pty Ltd ABN: 93 142 654 564 | Subject to change without notice www.actrol.com.au
 Pumps Accessories
Sauermann
Inline Filter
The Sauermann ACC17010 inline filter is designed for applications or conditions on site that requires advanced protection
against heavy particulates or pollutants that can cause damage to the system and/or reduce the longevity of the pump.

Applications such as:

• Industrial area with heavy dust particulate (workshops) • Food preparation areas and bakeries etc
(flour)
• Print rooms (print dust)

This inline filter is easy to install and comes with two male 6mm spigots.
Cat. No. Part No. Description
1602549 ACC17010 Inline Filter

Peristaltic Tube
The Sauermann PE5002 replacement tube is designed for replacing worn tubes and is easy to replace.
Suitable for the PE5000, PE5100, PE5200 pump Model. Comes with 2 cable ties for a firm and secure fit.
NB: Must be lubricated a silicone based lubricant (to prevent failure or early wear)

Cat. No. Part No. Description

2705834 PE-5002 Replacement Tube for Peristaltic Pumps

Peristaltic Head
The Sauermann PE5001 replacement head is designed for replacing pumps with burnt out motors, without the hassle of
rewiring the complete unit again. Simply screw off the head and unclip the electrical cable. Clip in the new one and re-screw
front face.Suitable for the PE5000, PE5100, PE5200 pump Model.

Cat. No. Part No. Description

1602611 PE-5001 Replacement Head for Peristaltic Pumps

AIR CONDITIONING HEATING REFRIGERATION

 Pumps Accessories
Sauermann
Float Detection Switch
The Sauermann ACC00601 float detection switch can be used as an additional safety alarm or to switch on or off the
pump / device. The control switch has a mechanical float switch which can be used in a NO or NC position.
Cat. No. Part No. Description
1602613 ACC00601 Float Detection Switch

Sensor Extension Cable

The Sauermann AC00705 sensor extension is used when the length between the pump and sensor needs to be increased.
The extension cable comes with a female connector.
Cat. No. Part No. Description
1602616 ACC00705 Sensor Extension Cable

Check Valve
The Sauermann ACC00801 replacement 10mm check valve is a quick fit solution. Comes with o-ring.
Cat. No. Part No. Description
1602614 ACC00801 10mm Check Valve

Detection Sensor
The Sauermann Si2958 is a universal float detection sensor designed to suit most piston pumps.
It comprises 3 switching levels:
• On = 16mm • Off = 1mm • High level alarm = 19mm
Cat. No. Part No. Description
1602610 SI-2958 Universal Float Detection Sensor

Adaptor Reducer
The Sauermann PE5003 is a reducer adapter suited for tubing installations when a reduction is required from 15mm. Steps
down in various sizes to a minimum 6mm. Comes with rubber connector.
Cat. No. Part No. Description
1602612 PE5003 15mm to 6mm Adaptor Reducer

Anti Siphoning Device

The Sauermann ACC00216 anti siphoning device is designed and used for in installations when the discharge point is lower
than the detector level which can cause siphoning through the pump. For 6mm hoses.
Cat. No. Part No. Description
1602618 ACC00216 Anti Siphoning Device

Inlet Adaptor
The Sauermann ACC02040 one size fits all adaptor can be used to connect two different diameter pipes together.
Specifically designed for centrifugal tank pumps.
Cat. No. Part No. Description
1602619 ACC02040 Multi Size Inlet Adaptor

Rubber Inlet Adaptors

The Sauermann ACC00110 special kit can be used to connect two different diameter pipes together via rubber inlet
adaptors, specially designed for centrifugal tank pumps. This kit comes with 6mm spigots.
Cat. No. Part No. Description
1602629 ACC00110 Rubber Inlet Adaptor Kit

Non Return Valves

The Sauermann ACC00805 pack of non return valves comprises 5 pieces of non return valves suitable for 6mm tubing.
Cat. No. Part No. Description
1602617 ACC00805 6mm Non Return Valves Pack of 5

Section 7 | 369
© 2017 Actrol Parts Pty Ltd ABN: 93 142 654 564 | Subject to change without notice www.actrol.com.au
 Evaporative Cooler Pumps
Fasco
JRM Pumps incorporate features based on a worldwide study and are manufactured in Australia using double coated
winding wire produced and tested in the JRM plant, thus assuring a top quality product.

Features
• 240 V, 50 Hz encapsulated, shaded pole motor • Auto reset overload • ABS plastic body mouldings
• Double insulated motor does not require earthing • Stainless steel shaft • Acetal impeller
• Precision double shielded ball bearings • Optional filter basket

Pumps
Cat. No. Part No. Description Watts Flow at 600mm Head Flow at 1600mm Head
1602528 Model 38 50 29.5l/m 23l/m
Evaporative Cooler Pump
1602529 Model 50 60 38l/m 30.5l/m

Accessories
Cat. No. Part No. Description
1602527 J-BASKET Evaporative Cooler Filter Basket

ebm-papst
Features
• Reliable external rotor motor • Efficient – up to 20% less energy use
• Performance improved by 20% • Easy replacement of most evap pumps on the market
• 2 year warranty • Exclusive proven design for harsh Australian conditions
• Low draft - requires minimum of only 57mm water depth

Cat. No. Part No. Description Watts Flow at 1m Head Flow at 2m Head
2704110 Alpha Pump Evaporative Cooler Pump 50 32l/m 25l/m

Propipe
Super Pump
Evaporative cooler field replacement pump; proven quality and reliability tested to As/NZs 60335.1:2011 electrical safety
requirements.
Features
• Intergrated filter basket • Quick fit assembly bracket
• Hi flow motor cooling venturi • Longlife Bearings
• Stainless steel shaft

Cat. No. Part No. Description Watts Flow at 600mm Flow at 1600mm
1602518 SP280 Super Pump Evaporative Cooler Pump 44 24.0 16.5
1602519 SP380 Super Pump Evaporative Cooler Pump 52 29.5 23.0
1602520 SP500 Super Pump Evaporative Cooler Pump 67 38.0 30.5

370 | Section 7
www.actrol.com.au Subject to change without notice | © 2017 Actrol Parts Pty Ltd ABN: 93 142 654 564
 Pumps - Other
Sump Dump
With the Sump Dump drainage system, evaporative coolers can now be operated with a hydraulically operated valve
ensuring reliable closing and draining in one movement.

As an active part of the cooler, incorporating only one solenoid for both water isolation and drainage, the Sump Dump™
System ensures that:
• The unit is completely dry and clean when not in use • The pads remain clean and odour free
• No residual water means no corrosion • The absence of stagnant water means no algal build-up

Kits
Kit Contents
• Complete retrofit dump valve unit • 24V solenoid
• 300mm SWC PVC drain adapter with O-ring • 6mm water supply tube from solenoid to valve
• 240V to 24V encapsulated transformer with 2 metre lead

Cat. No. Part No. Description

27076237 6001331 Dump Valve Kit

Replacement Parts
Cat. No. Part No. Description
27076592 6001336 Dump Valve Body
27076285 6001341 24V Solenoid with 6mm Straight Tube Connector
27076287 6001334 240V to 24V Transformer with 2m Leads

Little Giant
Submersible Pumps
Small submersible epoxy encapsulated pumps for commercial, industrial and home use. Applications include statuary
fountains, water displays, air conditioners, machine tool coolants, and many other applications where liquid must be
transferred or recirculated.

Features
• Continuous operation • Sump type pick-up • Epoxy encapsulated motor
• Can be installed on any of five sides • Removable inlet screen • Operates fully submerged
• Motor overload protection on PE-2
• Filled with special oil that provides lifetime lubrication & rapid dissipation of heat through housing

Flow at Flow at Discharge

Cat. No. Part No. Description Max Water Head
300mm Head 0mm Head Connection
1⁄
1602534 PE-1H Submersible 9l/m 10l/m 1400mm 4“ MNPT
1602535 PE-2 Pump 15l/m 18l/m 2500mm 1⁄
4“ MNPT

Section 7 | 371
© 2017 Actrol Parts Pty Ltd ABN: 93 142 654 564 | Subject to change without notice www.actrol.com.au
 Noise & Vibration Control Products
Refco
Anti-Vibration Pads
Refco’s AVP Pads are the latest generation in vibration dampening technology. AVP pads outperform cork or solid rubber
pads by a margin greater than 3:1. This enhanced performance is due to the special composite foam centre. The rubber
plates on top and on the bottom have opposing ribs to prevent the pad from moving under the vibrating machinery.
The AVP pad is also much more durable than for example cork as the AVP is not affected by oils, chemicals or humidity.

Cat. No. Part No. Model No. Description Size: mm

1609592 4507241 AVP-4 Anti-Vibration Pad 101 x 101 x 22

Mason
Waffle Pad
Load Ratings:
Cat. No. Part No. Size : mm
Durometer Load per 50 x 50 mm Sq. Rated Deflection : mm
2701723 18 x 18 SW 457 x 457 x 19 50 82 kg 2.5
1609584 R18 x 18 MSW 457 x 457 x 9.5 40 1.3 -

Metalflex
Tear Away Mounting Pads
Cat. No. Part No. Nominal Dimensions : mm
1606006 ADG3310K 300 x 300 x 10
1606007 ADG3315K 300 x 300 x 15

Propipe
Waffle Pad
Cat. No. Nominal Dimensions : mm
1609591 450 x 450 x 10
1609590 50 x 50 x 10

372 | Section 7
www.actrol.com.au Subject to change without notice | © 2017 Actrol Parts Pty Ltd ABN: 93 142 654 564
 Air Filtration
Filtratech
Disposable Filters
Size : mm Capacity : L/s Pressure Loss : Pa Performance
Cat. No. Model No.
Height Width Depth Low Medium High Low Medium High Rating

1602541 14x20x1 356 274 458 581

1602543 15x20x1 368 293 490 601
495
1602552 16x20x1 394 313 523 643
1602553 20x20x1 495 392 655 808
1602554 12x24x1 293 282 472 575
22 50 87
1602555 20x24x1 495 595 471 787 971
1602556 24x24x1 595 565 945 1168
1602542 14x25x1 356 343 574 730
1602544 16x25x1 394 622 392 655 808
1602557 20x25x1 495 490 819 1016
1602550 10x20x2 248 495 156 254 323
1602551 12x12x2 293 293 137 223 283
1602547 12x20x2 293 236 394 492
1602558 14x20x2 356 274 458 572
1602538 15x20x2 368
495
1602559 16x20x2 394 313 523 654
1602546 18x20x2 445 353 589 736
1602560 20x20x2 495 392 655 818
1602561 12x24x2 293 282 472 589 G4
48 32 65 90
1602539 14x24x2 356 338 550 700
1602545 16x24x2 394 375 610 773
595
1602562 18x24x2 445 423 708 883
1602563 20x24x2 495 471 787 982
1602564 24x24x2 595 565 945 1179
1602540 14x25x2 356 354 575 730
1602565 16x25x2 394 392 655 818
622
1602566 20x25x2 495 490 819 1022
1602548 20x30x2 495 588 983 1229
1602567 16x20x4 394 313 523 654
1602568 18x20x4 445 495 353 589 736
1602569 20x20x4 495 392 655 818
1602570 12x24x4 293 282 472 589
1602571 18x24x4 445 98 423 708 883 30 50 75
595
1602572 20x24x4 495 471 787 982
1602573 24x24x4 595 565 945 1179
1602574 16x25x4 394 392 655 818
622
1602575 20x25x4 495 490 819 1022

Section 7 | 373
© 2017 Actrol Parts Pty Ltd ABN: 93 142 654 564 | Subject to change without notice www.actrol.com.au
 Air Filtration
Space Filters
Deep Bed Bag Filters
Available in various sizes, styles and efficiencies deep bed bag filters are suitable for a wide variety of applications.

SpacePeak
The SpacePeak bag filter is made to fit a supporting inner basket and outer mounting frame.
Cat. No. Part No. Description Dimensions: mm Rating
1609558 SPACEPEAK664 Four Pyramid Bag Filter 610 x 610 x 380 F5
1609559 SPACEPEAK634 Two Pyramid Bag Filter 610 x 305 x 380 F5

SpacePak
The SpacePak bag filter comes with a self-supporting wire header. Using this filter with the wire header eliminates the need
for the inner wire basket.
Cat. No. Part No. Description Dimensions: mm Rating
1609560 SPACEPAK663W Three Pocket Bag Filter with Wire 610 x 610 x 570 F5
1609561 SPACEPAK632W Two Pocket Bag Filter with Wire 610 x 305 x 570 F5

SpaceCube
The SpaceCube deep bed filters are ideal general-purpose filters for applications where high efficiency and long duty cycles
are required. These filters offer superior performance to typical roll type and metal viscous filters. The key to the excellent
performance of these filters is their shape. The SpaceCube is a pyramid within a cube in construction.
Cat. No. Part No. Description Dimensions: mm Rating
1609562 SPACECUBE66 Cube Style Bag Filter 610 x 610 x 600 F5
1609563 SPACECUBE63 Cube Style Bag Filter 610 x 305 x 600 F5

SpaceCone
The SpaceCone deep bed filters are ideal general-purpose filters for applications where high efficiency and long duty cycles
are required. These filters offer superior performance to typical roll type and metal viscous filters. The key to the excellent
performance of these filters is their shape. The SpaceCone is a cone within a truncated cone.
Cat. No. Part No. Description Dimensions: mm Rating
1609564 SPACECONE66 Cone Style Bag Filter 610 x 610 x 660 F5
1609565 SPACECONE63 Cone Style Bag Filter 610 x 305 x 660 F5

Multi-Pocket High Efficiency Bag Filters

PrecisionPak extended surface bag filters are designed for use in most commercial or industrial HVAC systems where
medium to high efficiency filtration is required and are manufactured from micro-fine synthetic media.
Cat. No. Part No. Description Dimensions: mm No. of Pockets Rating
1609566 PAP665S4422 Multi-Pocket Bag Filter 610 x 610 x 559 6 F6
1609567 PAP365S2422 Multi-Pocket Bag Filter 610 x 305 x 559 3 F6
1609568 PAP685S4422 Multi-Pocket Bag Filter 610 x 610 x 559 6 F7
1609569 PAP385S2422 Multi-Pocket Bag Filter 610 x 305 x 559 3 F7
1609570 PAP895S4422 Multi-Pocket Bag Filter 610 x 610 x 559 8 F8
1609571 PAP495S2422 Multi-Pocket Bag Filter 610 x 305 x 559 4 F8

374 | Section 7
www.actrol.com.au Subject to change without notice | © 2017 Actrol Parts Pty Ltd ABN: 93 142 654 564