SAINT MARY’S ACADEMY OF CAPIZ P. Burgos St.

, Roxas
City
SY 2023-2024

TLE 7
(Technical Drafting)
Fourth Quarter Work
text 1

An Introduction to Drafting and Technical Drawing

Technical Drawing
Technical drawing, also known as drafting, is the academic discipline of creating
standardized technical drawings by architects, interior designers, drafters, design engineers, and
related professionals. Standards and conventions for layout, line thickness, text size, symbols,
view projections, descriptive geometry, dimensioning, and notation are used to create
drawings that are ideally interpreted in only one way.

Why do we need Technical Drawings?

Have you ever tried to assemble something without a diagram? You won’t get very far.
Technical drawings are visual instructions used to help us determine the overall layout and design
of what is being drafted. Example: A floor plan of a house.

Artistic Drawings vs. Technical Drawings

A technical drawing shows how an object should look, how it will be put together, or how it
looks from different directions and is drawn to scale. Artistic drawings allow for distortion and
artist’s interpretation.

Lesson
Use of Hand Tools

1 and Equipment
Lesson 1 – Use of Hand Tools and Equipment After going through this module, you are
expected to:
1. list hand tools based on job requirements;
2. identify appropriate hand tools; and
3. classify hand tools according to function and task requirements.
 DRAFTING MATERIALS AND TOOLS, ITS
USES/FUNCTIONS

There are a great variety of drafting materials and tools used in

mechanical drawing. The drafting materials and tools discussed in this
Module include most of the basic ones but sufficient enough for your initial
understanding about technical drawing.
PICTURES/ILLUSTRATION MATERIALS, DESCRIPTION AND
S FUNCTION

Drawing paper

Various types of drawing papers are available

for use but hard and soft surface drawing
papers are highly recommended to be the
best. This type does not groove easily when
pressure is applied to the pencil. Oslo paper is
commonly used but bond paper is also
recommended.

Masking tape

This is used for fastening the drawing paper

on the drawing table or drawing board
because it does not damage the board and it
will not damage the paper if it is removed by
pulling it off.

Pencil sharpener

Pencils should be sharpened whenever

they show sign of dullness. Various types
and designs are available in the store for
use.

Eraser

This is used to clean the dirt of the drawing.

A soft eraser is advantageous in removing
smudges and pencil marks, whereas, a
harder eraser is useful for making changes
and correcting errors in the drawing.
 Drawing pencil

This is one of the most important tools in

drawing. It comes in various grades. The grade
of pencil to be used depends on the quality of
paper to be used. You have to take into
consideration also the type of line work
required.
Types of Drawing Pencil
Hard pencils – are used where extreme accuracy
is required especially working on graphs,
diagrams and charts.

Medium pencils – are used for general

purpose work in drawing.

Soft pencils – are too soft to be used in

mechanical drafting. They are very useful for
art work of various kinds.

MEASURING TOOLS
PICTURES/ILLUSTRATION MATERIALS AND TOOLS DESCRIPTION
S

T-Square

It is a drawing instrument used when

making horizontal lines. It is also used for
guiding triangles when drawing vertical lines.
It is made of wood, plastic or the
combination of both.There are three (3)
types of Tsquare, namely:

1. Fixed Head. The head is fastened to

the blade. It is used for ordinary work.

2. Movable Head or Adjustable Head. It

has one fixed and one adjustable
head and used only for occasional
drawing.

3. Detachable Head or Removable

Head. It isdesigned for comfort when
 carrying
the T-square.

Triangle

It is a three-sided ruler, which typically has

two equal sides meeting at a 90 degree angle
and to a third side at 45, 30, including 60
degree angles. It is usually made of plastic
and comes in different sizes. If in use, the
base of the triangle must rest on the blade of
the T-square. Drawing a line always starts
from the point near the base going upward.
Commonly used triangles are:

a. 30 degrees X 60 degrees
b. 45 degrees X 45 degrees

Compass

This drawing instrument is used when

drawing arcs and circles. It is used in a
similar way to a divider. It is composed of
one with the pen leg
and the needle point leg being held together
with a handle. This drawing instrument can
be used for both penciling and inking.

Divider

This is a drawing instrument used when

transferring measurements, dividing lines
and arcs into the desired number of equal
parts. It can easily transfer accurate
measurements by adjusting the divider
points. Constant correct practice is
necessary before doing an actual work for a
quick and easy control when use.
 Ruler

A ruler, sometimes called a rule or line

gauge, is a device used technical drawing, to
measure distances or draw straight lines.
This drafting tool is used when drawing
vertical lines.

Protractor

It is a semi-circular instrument divided into

180 equal parts, each of which is called a
degree. It is used to determine gradations of
the degrees when measuring arcs, angles
and circles. High quality protractor is usually
made of plastic.

Activity 1: Direction: Continue the following sentences using your

knowledge on preparing hand tools in technical drafting. Use the given activity
sheet for your answer.

1. Listing hand tools based on job requirement is important because

…

2. Classifying hand tools according to its function is important

because …

Activity 2: Direction: Select the drafting material and tool applicable to a specific
job. Encircle the letter of the correct answer. Use the given activity sheet for your
answer.
1. Why does a drafter need a t-square?
a. to have guide in drawing horizontal line
b. to help in navigating direction
c. to help in measuring blueprints
d. to get accurate parallel lines

2. Which Drawing instrument is similar to a divider when used? a.

compass
b. triangle
c. t- square
d. triangular scales
 3. Why is it necessary to use masking tape in drawing?
a. to tighten the drawing board
b. to add color to the drawing paper
c. to fasten the drawing paper on the drawing paper on the drawing board d. to
make the task easy

4. It is a three-sided ruler, which typically has two equal sides meeting at a 90 degree
angle and to a third side at 45, 30, including 60 degree angles. a. compass
b. hard pencil
c. masking tape
d. triangle

5. What tool will you used in to reproduce the measurement of an object to any size?
a. ruler
b. protractor
c. triangle
d. triangular scales
6. What drawing instrument will be used when transferring measurements,
dividing lines and arcs into the desired number of equal parts? a. compass
b. divider
c. masking tape
d. triangular scales

7. What drafting tool is used to protect the rest of the drawing when removing
unnecessary lines?
a. erasing shield
b. eraser
c. masking tape
d. pencil sharpener

8. How do we determine gradations of the degrees when measuring arcs, angles and
circles?
a. by using compass
b. by using protractor
c. by using triangle
d. by using triangular scales

9. This drafting tool is used when drawing vertical lines.

a. compass
b. triangle
c. triangular scales
d. ruler

10. When does a pencil need to be sharpened?

a. when it shows sign of dullness
b. when it is necessary
c. when it is used by anybody
d. when it is wet
References

TLE_EM7/8-00-1(Accessed April 1, 2024)

DepEd TLE Learning Module Mechanical Drafting (Accessed April 1, 2024)