MTS9300A Telecom Power

V100R002C00

User Manual

Issue 11
Date 2023-03-15

HUAWEI TECHNOLOGIES CO., LTD.

Copyright © Huawei Technologies Co., Ltd. 2023. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.

Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees
or representations of any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China

Website: https://www.huawei.com
Email: [email protected]

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. i

MTS9300A Telecom Power
User Manual About This Document

About This Document

Purpose
This document describes the product features, components, and maintenance
methods.

Figures provided in this document are for reference only.

Intended Audience
This document is intended for:

● Sales engineers
● Technical support engineers
● Maintenance engineers

Symbol Conventions
The symbols that may be found in this document are defined as follows.

Symbol Description

Indicates a hazard with a high level of risk which, if not

avoided, will result in death or serious injury.

Indicates a hazard with a medium level of risk which, if not

avoided, could result in death or serious injury.

Indicates a hazard with a low level of risk which, if not

avoided, could result in minor or moderate injury.

Indicates a potentially hazardous situation (for device or

environment safety) which, if not avoided, could result in
equipment damage, data loss, performance deterioration, or
unanticipated results.
NOTICE is used to address practices not related to personal
injury.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. ii

MTS9300A Telecom Power
User Manual About This Document

Symbol Description

Supplements the important information in the main text.

NOTE is used to address information not related to personal
injury, equipment damage, and environment deterioration.

Change History
Changes between document issues are cumulative. The latest document issue
contains all updates made in previous issues.

Issue 11 (2023-03-15)
Updated the safety information in this document.
Changed the UIM model to UIM02C.

Issue 10 (2023-01-06)
● Added content of TCUC and TCUE.
● Added 4.1.8 Cleaning the Heat Exchanger Core.

Issue 09 (2022-02-15)
Updated 3.12.1 Appearance.

Issue 08 (2021-09-13)
Added content of AC heater.

Issue 07 (2021-05-06)
Optimized the description of the document.

Issue 06 (2020-10-31)
● Added MTS9300A-HX1001.
● Added contents of PVDU-80A1.
● Updated content of EPS100D-N01D1 Indoor DC Blade Power Supply.
● Added SMU11C.

Issue 05 (2019-12-17)
Optimized the content of the document.

Issue 04 (2019-11-25)
Deleted contents about the app and WiFi.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. iii

MTS9300A Telecom Power
User Manual About This Document

Issue 03 (2019-06-30)
Deleted iBOX and iBAT.

Issue 02 (2019-01-30)
Added the description of blade power supply.

Issue 01 (2018-10-30)
This issue is the first official release.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. iv

MTS9300A Telecom Power
User Manual Contents

Contents

About This Document................................................................................................................ ii

1 Safety Information.................................................................................................................. 1
1.1 Personal Safety.........................................................................................................................................................................2
1.2 Electrical Safety........................................................................................................................................................................ 4
1.3 Environment Requirements................................................................................................................................................. 8
1.4 Mechanical Safety.................................................................................................................................................................10
1.5 Battery Safety......................................................................................................................................................................... 15
1.6 PV Module Safety................................................................................................................................................................. 21

2 Product Overview.................................................................................................................. 23
2.1 Overview.................................................................................................................................................................................. 23
2.2 Cabinet Description.............................................................................................................................................................. 23
2.2.1 MTS9302A-HD16A3..........................................................................................................................................................24
2.2.2 MTS9302A-HD16A2..........................................................................................................................................................27
2.2.3 MTS9302A-HD10A2..........................................................................................................................................................30
2.2.4 MTS9302A-HA16A3.......................................................................................................................................................... 32
2.2.5 MTS9302A-HA16A2.......................................................................................................................................................... 35
2.2.6 MTS9303A-HX10A2.......................................................................................................................................................... 38
2.2.7 MTS9302A-HX10A4.......................................................................................................................................................... 40
2.2.8 MTS9302A-HX10A3.......................................................................................................................................................... 42
2.2.9 MTS9300A-XD10A2.......................................................................................................................................................... 44
2.2.10 MTS9300A-XA10A2........................................................................................................................................................ 46
2.2.11 MTS9300A-HX1001........................................................................................................................................................ 47

3 Components............................................................................................................................50
3.1 Power Distribution Unit...................................................................................................................................................... 50
3.1.1 Power Subrack.................................................................................................................................................................... 50
3.1.2 AC and DC Power Distribution Boxes......................................................................................................................... 54
3.2 Rectifier.................................................................................................................................................................................... 55
3.3 (Optional) S4850G1............................................................................................................................................................. 57
3.4 (Optional) PVDU-80A1....................................................................................................................................................... 58
3.5 Monitoring Module SMU02C............................................................................................................................................ 60
3.6 SMU11C....................................................................................................................................................................................64
3.7 SMU11D................................................................................................................................................................................... 69

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. v

MTS9300A Telecom Power
User Manual Contents

3.8 User Interface Module UIM02C....................................................................................................................................... 74

3.9 Communications Expansion Module CIM02C............................................................................................................. 77
3.10 Communications Expansion Module NIM01C3........................................................................................................79
3.11 EPS100D-N01D1 DC Blade Power Supply................................................................................................................. 82
3.11.1 Appearance....................................................................................................................................................................... 83
3.11.2 Technical Specifications................................................................................................................................................ 83
3.12 EPS100D-N02A1 AC Blade Power Supply.................................................................................................................. 85
3.12.1 Appearance....................................................................................................................................................................... 85
3.12.2 Technical Specifications................................................................................................................................................ 86
3.13 DC-DC Module (C6030G1).............................................................................................................................................. 88
3.14 DC Air Conditioner PC300D............................................................................................................................................ 89
3.15 Top Extended Temperature Control Device HXC100F............................................................................................ 90
3.16 TCUC....................................................................................................................................................................................... 91
3.17 TCUE........................................................................................................................................................................................ 93
3.18 DC Heater..............................................................................................................................................................................94
3.19 AC Heater.............................................................................................................................................................................. 95
3.20 Electronic Lock..................................................................................................................................................................... 96
3.21 Sensors................................................................................................................................................................................... 98
3.21.1 Smoke Sensor................................................................................................................................................................... 98
3.21.2 Temperature and Humidity Sensor........................................................................................................................... 99
3.21.3 Water Sensor.................................................................................................................................................................. 100
3.21.4 Door Status Sensor...................................................................................................................................................... 100
3.21.5 Battery Temperature Sensor..................................................................................................................................... 101
3.22 Light...................................................................................................................................................................................... 101

4 System Maintenance.......................................................................................................... 102

4.1 Routine Maintenance........................................................................................................................................................ 102
4.1.1 Routine Maintenance for Cabinets........................................................................................................................... 102
4.1.2 Routine Maintenance for Temperature Control Equipment.............................................................................104
4.1.3 AC and DC Power Distribution................................................................................................................................... 104
4.1.4 Rectifier...............................................................................................................................................................................106
4.1.5 Monitoring Unit............................................................................................................................................................... 107
4.1.6 Parameters on the SMU............................................................................................................................................... 107
4.1.7 Cables.................................................................................................................................................................................. 108
4.1.8 Cleaning the Heat Exchanger Core........................................................................................................................... 109
4.2 Identifying Component Faults........................................................................................................................................112
4.2.1 Identifying Rectifier Faults........................................................................................................................................... 112
4.2.2 Identifying SSU Faults................................................................................................................................................... 113
4.2.3 Identifying AC SPD Faults............................................................................................................................................ 113
4.2.4 Identifying Circuit Breaker Faults.............................................................................................................................. 113
4.2.5 Identifying SMU Faults.................................................................................................................................................. 113
4.3 Components Replacement.............................................................................................................................................. 114
4.3.1 Replacing a Rectifier...................................................................................................................................................... 114

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. vi

MTS9300A Telecom Power
User Manual Contents

4.3.2 Replacing an S4850G1.................................................................................................................................................. 115

4.3.3 Replacing a PVDU-80A1............................................................................................................................................... 117
4.3.4 Replacing an AC SPD Module..................................................................................................................................... 118
4.3.5 Replacing a Circuit Breaker..........................................................................................................................................119
4.3.6 Replacing an SMU02C................................................................................................................................................... 120
4.3.7 Replacing an SMU11C................................................................................................................................................... 121
4.3.8 Replacing an SMU11D.................................................................................................................................................. 123
4.3.9 Replacing a UIM02C Board..........................................................................................................................................124
4.3.10 Replacing a CIM02C.....................................................................................................................................................126
4.3.11 Replacing an NIM01C3............................................................................................................................................... 127
4.3.12 Replacing Heat Exchanger Fans.............................................................................................................................. 128
4.3.13 Replacing a TCUC Control Board (Horizontal installation)........................................................................... 131
4.3.14 Replacing a TCUC Control Board............................................................................................................................ 134
4.3.15 Replacing a TCUE Control Board (Horizontal installation)............................................................................137
4.3.16 Replacing a TCUE Control Board............................................................................................................................. 139
4.3.17 Replacing a Smoke Sensor........................................................................................................................................ 142
4.3.18 Replacing a Temperature and Humidity Sensor (UIM02C)........................................................................... 143
4.3.19 Replacing a Door Status Sensor.............................................................................................................................. 146
4.3.20 Replacing a Battery Temperature Sensor (UIM02C)........................................................................................ 147
4.3.21 Replacing an Electronic Lock.................................................................................................................................... 148

A Operating Environment.................................................................................................... 151

B Technical Specifications.....................................................................................................152
B.1 Environment Specifications............................................................................................................................................. 152
B.2 Electrical Specifications.................................................................................................................................................... 153
B.3 EMC Specifications............................................................................................................................................................. 154

C Electrical Conceptual Diagrams...................................................................................... 156

D Associations Between Alarms and Dry Contacts on the UIM.................................. 158
E How Do I Change the Communications Protocol for COM4 and COM5?..............160
F Symbol Conventions........................................................................................................... 162
G Acronyms and Abbreviations........................................................................................... 164

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. vii

MTS9300A Telecom Power
User Manual 1 Safety Information

1 Safety Information

Statement
Before transporting, storing, installing, operating, using, and/or maintaining
the equipment, read this document, strictly follow the instructions provided
herein, and follow all the safety instructions on the equipment and in this
document. In this document, "equipment" refers to the products, software,
components, spare parts, and/or services related to this document; "the Company"
refers to the manufacturer (producer), seller, and/or service provider of the
equipment; "you" refers to the entity that transports, stores, installs, operates,
uses, and/or maintains the equipment.

The Danger, Warning, Caution, and Notice statements described in this

document do not cover all the safety precautions. You also need to comply with
relevant international, national, or regional standards and industry practices. The
Company shall not be liable for any consequences that may arise due to
violations of safety requirements or safety standards concerning the design,
production, and usage of the equipment.

The equipment should be used in an environment that meets the design

specifications. Otherwise, the equipment may be faulty, malfunctioning, or
damaged, which is not covered under the warranty. The Company shall not be
liable for any property loss, personal injury, or even death caused thereby.

Comply with applicable laws, regulations, standards, and specifications during

transportation, storage, installation, operation, use, and maintenance.

Do not perform reverse engineering, decompilation, disassembly, adaptation,

implantation, or other derivative operations on the equipment software. Do not
study the internal implementation logic of the equipment, obtain the source code
of the equipment software, violate intellectual property rights, or disclose any of
the performance test results of the equipment software.

The Company shall not be liable for any of the following circumstances or
their consequences:

● Equipment damage due to force majeure such as earthquakes, floods,

volcanic eruptions, debris flows, lightning strikes, fires, wars, armed conflicts,
typhoons, hurricanes, tornadoes, and extreme weather conditions
● Operation beyond the conditions specified in this document

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 1

MTS9300A Telecom Power
User Manual 1 Safety Information

● Installation or use in environments that do not comply with international,

national, or regional standards
● Installation or use by unqualified personnel
● Failure to follow the operation instructions and safety precautions on the
product and in the document
● Unauthorized modifications to the product or software code or removal of the
product
● Damage caused during transportation by you or a third party authorized by
you
● Storage conditions that do not meet the requirements specified in the product
document
● Failure to comply with local laws, regulations, or related standards due to the
materials and tools prepared by you
● Damage caused by your or a third party's negligence, intentional breach,
gross negligence, or improper operations or damage not caused by the
Company

1.1 Personal Safety

DANGER

Do not work with power on during installation. Do not install or remove a cable
with power on. Transient contact between the core of the cable and a conductor
will generate electric arcs or sparks, which may cause a fire or personal injury.

DANGER

Non-standard and improper operations on the energized equipment may cause

fire or electric shocks, resulting in property damage, personal injury, or even death.

DANGER

Before operations, remove conductive objects such as watches, bracelets, bangles,

rings, and necklaces to prevent electric shocks.

DANGER

During operations, use dedicated insulated tools to prevent electric shocks or short
circuits. The insulation and voltage resistance must comply with local laws,
regulations, standards, and specifications.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 2

MTS9300A Telecom Power
User Manual 1 Safety Information

WARNING

During operations, wear personal protective equipment such as protective

clothing, insulated shoes, goggles, safety helmets, and insulated gloves.

Figure 1-1 Personal protective equipment

General Requirements
● Do not stop protective devices. Pay attention to the warnings, cautions, and
related precautionary measures in this document and on the equipment.
● If there is a likelihood of personal injury or equipment damage during
operations, immediately stop, report the case to the supervisor, and take
feasible protective measures.
● Do not power on the equipment before it is installed or confirmed by
professionals.
● Do not touch the power supply equipment directly or with conductors such as
damp objects. Before touching any conductor surface or terminal, measure
the voltage at the contact point to ensure that there is no risk of electric
shock.
● Do not touch a running fan with your hands, components, screws, tools, or
boards. Otherwise, personal injury or equipment damage may occur.
● In the case of a fire, immediately leave the building or the equipment area
and activate the fire alarm or call emergency services. Do not enter the
affected building or equipment area under any circumstances.

Personnel Requirements
● Only professionals and trained personnel are allowed to operate the
equipment.
– Professionals: personnel who are familiar with the working principles and
structure of the equipment, trained or experienced in equipment
operations and are clear of the sources and degree of various potential
hazards in equipment installation, operation, maintenance
– Trained personnel: personnel who are trained in technology and safety,
have required experience, are aware of possible hazards on themselves in

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 3

MTS9300A Telecom Power
User Manual 1 Safety Information

certain operations, and are able to take protective measures to minimize

the hazards on themselves and other people
● Personnel who plan to install or maintain the equipment must receive
adequate training, be able to correctly perform all operations, and understand
all necessary safety precautions and local relevant standards.
● Only qualified professionals or trained personnel are allowed to install,
operate, and maintain the equipment.
● Only qualified professionals are allowed to remove safety facilities and inspect
the equipment.
● Personnel who will perform special tasks such as electrical operations,
working at heights, and operations of special equipment must possess the
required local qualifications.
● Only authorized professionals are allowed to replace the equipment or
components (including software).
● Only personnel who need to work on the equipment are allowed to access
the equipment.

1.2 Electrical Safety

DANGER

Before connecting cables, ensure that the equipment is intact. Otherwise, electric
shocks or fires may occur.

DANGER

Non-standard and improper operations may result in fire or electric shocks.

DANGER

Prevent foreign matter from entering the equipment during operations. Otherwise,
equipment damage, load power derating, power failure, or personal injury may
occur.

WARNING

For the equipment that needs to be grounded, install the ground cable first when
installing the equipment and remove the ground cable last when removing the
equipment.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 4

MTS9300A Telecom Power
User Manual 1 Safety Information

CAUTION

Do not route cables near the air intake or exhaust vents of the equipment.

CAUTION

Do not directly connect aluminum cables to prevent electrochemical corrosion of

copper and aluminum.

General Requirements
● Follow the procedures described in the document for installation, operation,
and maintenance. Do not reconstruct or alter the equipment, add
components, or change the installation sequence without permission.
● Install temporary fences or warning ropes and hang "No Entry" signs around
the operation area to keep unauthorized personnel away from the area.
● Before installing or removing power cables, turn off the switches of the
equipment and its upstream and downstream switches.
● If any liquid is detected inside the equipment, disconnect the power supply
immediately and do not use the equipment.
● Before performing operations on the equipment, check that all tools meet the
requirements and record the tools. After the operations are complete, collect
all of the tools to prevent them from being left inside the equipment.
● Before installing power cables, check that cable labels are correct and cable
terminals are insulated.
● When installing the equipment, use a torque tool of a proper measurement
range to tighten the screws. When using a wrench to tighten the screws,
ensure that the wrench does not tilt and the torque error does not exceed
10% of the specified value.
● Ensure that bolts are tightened with a torque tool and marked in red and blue
after double-check. Installation personnel mark tightened bolts in blue.
Quality inspection personnel confirm that the bolts are tightened and then
mark them in red. (The marks should cross the edges of the bolts.)

● To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits
to telecommunication network voltage (TNV) circuits.
● Ensure that all slots are installed with boards or filler panels. Avoid hazards
caused by hazardous voltages or energy on boards. Ensure that the air
channel is normal, control electromagnetic interference, and prevent dust and
other foreign objects on the backplane, baseplate, and boards.
● After the installation is complete, ensure that protective cases, insulation
tubes, and other necessary items for all electrical components are in position
to avoid electric shocks.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 5

MTS9300A Telecom Power
User Manual 1 Safety Information

● If the power supply to the equipment is permanently connected, install an

easily accessible disconnector at the exterior of the device.
● If the equipment has multiple inputs, disconnect all the inputs before
operating the equipment.
● Before maintaining a downstream electrical or power distribution device, turn
off the output switch on the power supply equipment.
● During equipment maintenance, attach "Do not switch on" labels near the
upstream and downstream switches or circuit breakers as well as warning
signs to prevent accidental connection. The equipment can be powered on
only after troubleshooting is complete.
● If fault diagnosis and troubleshooting need to be performed after power-off,
take the following safety measures: Disconnect the power supply. Check
whether the equipment is live. Install a ground cable. Hang warning signs and
set up fences.
● Check equipment connections periodically, ensuring that all screws are
securely tightened.
● Only qualified professionals can replace a damaged cable.
● Do not scrawl, damage, or block any labels or nameplates on the equipment.
Promptly replace labels that have worn out.
● Do not use solvents such as water, alcohol, or oil to clean electrical
components inside or outside of the equipment.

Grounding
● Ensure that the grounding impedance of the equipment complies with local
electrical standards.
● Ensure that the equipment is connected permanently to the protective
ground. Before operating the equipment, check its electrical connection to
ensure that it is reliably grounded.
● Ensure that the protective ground point of the equipment is reliably
connected to the ground screw of the metal enclosure (connection resistance:
≤ 0.1 ohm).
● Do not operate the equipment in the absence of a properly installed ground
conductor.
● Do not damage the ground conductor.
● For the equipment that uses a three-pin socket, ensure that the ground
terminal in the socket is connected to the protective ground point.
● If high touch current may occur on the equipment, ground the protective
ground terminal on the equipment enclosure before connecting the power
supply; otherwise, electric shock as a result of touch current may occur.

Cabling
● When selecting, installing, and routing cables, follow local safety regulations
and rules.
● When routing power cables, ensure that there is no coiling or twisting. Do not
join or weld power cables. If necessary, use a longer cable.
● Ensure that all cables are properly connected and insulated, and meet
specifications.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 6

MTS9300A Telecom Power
User Manual 1 Safety Information

● Ensure that the slots and holes for routing cables are free from sharp edges,
and that the positions where cables are routed through pipes or cable holes
are equipped with cushion materials to prevent the cables from being
damaged by sharp edges or burrs.
● If a cable is connected to the cabinet from the top, bend the cable in a U
shape outside the cabinet and then route it into the cabinet.
● Ensure that cables of the same type are bound together neatly and straight
and that the cable sheath is intact. When routing cables of different types,
ensure that they are away from each other without entanglement and
overlapping.
● When cable connection is completed or paused for a short period of time, seal
the cable holes with sealing putty immediately to prevent small animals or
moisture from entering.
● Secure buried cables using cable supports and cable clips. Ensure that the
cables in the backfill area are in close contact with the ground to prevent
cable deformation or damage during backfilling.
● If the external conditions (such as the cable layout or ambient temperature)
change, verify the cable usage in accordance with the IEC-60364-5-52 or local
laws and regulations. For example, check that the current-carrying capacity
meets requirements.
● Do not perform any improper operations, for example, dropping cables
directly from a vehicle. Otherwise, the cable performance may deteriorate due
to cable damage, which affects the current-carrying capacity and temperature
rise.

Electrostatic Discharge (ESD)

NOTICE

The static electricity generated by human bodies may damage the electrostatic-
sensitive components on boards, for example, the large-scale integrated (LSI)
circuits.

● When touching the equipment and handling boards, modules with exposed
circuit boards, or application-specific integrated circuits (ASICs), observe ESD
protection regulations and wear ESD clothing and ESD gloves or a well-
grounded ESD wrist strap.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 7

MTS9300A Telecom Power
User Manual 1 Safety Information

Figure 1-2 Wearing an ESD wrist strap

● When holding a board or a module with exposed circuit boards, hold its edge
without touching any components. Do not touch the components with bare
hands.
● Package boards or modules with ESD packaging materials before storing or
transporting them.

1.3 Environment Requirements

DANGER

Do not expose the equipment to flammable or explosive gas or smoke. Do not

perform any operation on the equipment in such environments.

DANGER

Do not store any flammable or explosive materials in the equipment area.

DANGER

Do not place the equipment near heat sources or fire sources, such as smoke,
candles, heaters, or other heating devices. Overheat may damage the equipment
or cause a fire.

WARNING

Install the equipment in an area far away from liquids. Do not install it under
areas prone to condensation, such as under water pipes and air exhaust vents, or
areas prone to water leakage, such as air conditioner vents, ventilation vents, or
feeder windows of the equipment room. Ensure that no liquid enters the
equipment to prevent faults or short circuits.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 8

MTS9300A Telecom Power
User Manual 1 Safety Information

WARNING

To prevent damage or fire due to high temperature, ensure that the ventilation
vents or heat dissipation systems are not obstructed or covered by other objects
while the equipment is running.

General Requirements
● Ensure that the equipment is stored in a clean, dry, and well ventilated area
with proper temperature and humidity and is protected from dust and
condensation.
● Keep the installation and operating environments of the equipment within the
allowed ranges. Otherwise, its performance and safety will be compromised.
● Do not install, use, or operate outdoor equipment and cables (including but
not limited to moving equipment, operating equipment and cables, inserting
connectors to or removing connectors from signal ports connected to outdoor
facilities, working at heights, performing outdoor installation, and opening
doors) in harsh weather conditions such as lightning, rain, snow, and level 6
or stronger wind.
● Do not install the equipment in an environment with dust, smoke, volatile or
corrosive gases, infrared and other radiations, organic solvents, or salty air.
● Do not install the equipment in an environment with conductive metal or
magnetic dust.
● Do not install the equipment in an area conducive to the growth of
microorganisms such as fungus or mildew.
● Do not install the equipment in an area with strong vibration, noise, or
electromagnetic interference.
● Ensure that the site complies with local laws, regulations, and related
standards.
● Ensure that the ground in the installation environment is solid, free from
spongy or soft soil, and not prone to subsidence. The site must not be located
in a low-lying land or an area prone to water or snow accumulation, and the
horizontal level of the site must be above the highest water level of that area
in history.
● If the equipment is installed in a place with abundant vegetation, in addition
to routine weeding, harden the ground underneath the equipment using
cement or gravel.
● Before opening doors during the installation, operation, and maintenance of
the equipment, clean up any water, ice, snow, or other foreign objects on the
top of the equipment to prevent foreign objects from falling into the
equipment.
● When installing the equipment, ensure that the installation surface is solid
enough to bear the weight of the equipment.
● All cable holes should be sealed. Seal the used cable holes with sealing putty.
Seal the unused cable holes with the caps delivered with the equipment. The
following figure shows the criteria for correct sealing with sealing putty.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 9

MTS9300A Telecom Power
User Manual 1 Safety Information

● After installing the equipment, remove the packing materials such as cartons,
foam, plastics, and cable ties from the equipment area.

1.4 Mechanical Safety

DANGER

When working at heights, wear a safety helmet and safety harness or waist belt
and fasten it to a solid structure. Do not mount it on an insecure moveable object
or metal object with sharp edges. Make sure that the hooks will not slide off.

WARNING

Ensure that all necessary tools are ready and inspected by a professional
organization. Do not use tools that have signs of scratches or fail to pass the
inspection or whose inspection validity period has expired. Ensure that the tools
are secure and not overloaded.

WARNING

Before installing equipment in a cabinet, ensure that the cabinet is securely

fastened with a balanced center of gravity. Otherwise, tipping or falling cabinets
may cause bodily injury and equipment damage.

WARNING

When pulling equipment out of a cabinet, be aware of unstable or heavy objects

in the cabinet to prevent injury.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 10

MTS9300A Telecom Power
User Manual 1 Safety Information

WARNING

Do not drill holes into the equipment. Doing so may affect the sealing
performance and electromagnetic containment of the equipment and damage
components or cables inside. Metal shavings from drilling may short-circuit boards
inside the equipment.

General Requirements
● Repaint any paint scratches caused during equipment transportation or
installation in a timely manner. Equipment with scratches cannot be exposed
for an extended period of time.
● Do not perform operations such as arc welding and cutting on the equipment
without evaluation by the Company.
● Do not install other devices on the top of the equipment without evaluation
by the Company.
● When performing operations over the top of the equipment, take measures to
protect the equipment against damage.
● Use correct tools and operate them in the correct way.

Moving Heavy Objects

● Be cautious to prevent injury when moving heavy objects.

● If multiple persons need to move a heavy object together, determine the

manpower and work division with consideration of height and other
conditions to ensure that the weight is equally distributed.
● If two persons or more move a heavy object together, ensure that the object
is lifted and landed simultaneously and moved at a uniform pace under the
supervision of one person.
● Wear personal protective gears such as protective gloves and shoes when
manually moving the equipment.
● To move an object by hand, approach to the object, squat down, and then lift
the object gently and stably by the force of the legs instead of your back. Do
not lift it suddenly or turn your body around.
● Move or lift the equipment by holding its handles or lower edges. Do not hold
the handles of modules that are installed in the equipment.
● Do not quickly lift a heavy object above your waist. Place the object on a
workbench that is half-waist high or any other appropriate place, adjust the
positions of your palms, and then lift it.
● Move a heavy object stably with balanced force at an even and low speed. Put
down the object stably and slowly to prevent any collision or drop from
scratching the surface of the equipment or damaging the components and
cables.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 11

MTS9300A Telecom Power
User Manual 1 Safety Information

● When moving a heavy object, be aware of the workbench, slope, staircase,

and slippery places. When moving a heavy object through a door, ensure that
the door is wide enough to move the object and avoid bumping or injury.
● When transferring a heavy object, move your feet instead of turning your
waist around. When lifting and transferring a heavy object, ensure that your
feet point to the target direction of movement.
● When transporting the equipment using a pallet truck, ensure that the forks
are properly positioned so that the equipment does not topple. Before moving
the equipment, secure it to the pallet truck using ropes. When moving the
equipment, assign dedicated personnel to take care of it.
● Transport the equipment by sea or on roads with good conditions. Minimize
jolt and tilt during transportation.
● Ensure that tilt angle of the cabinet meets the requirements shown in the
figure. The tilt angle α of the packed cabinet must be less than or equal to
15°. After the cabinet is unpacked, its tilt angle α must be less than or equal
to 10°.

Working at Heights
● Any operations performed 2 meters or higher above the ground should be
supervised properly.
● Only trained and qualified personnel are allowed to work at heights.
● Do not work at heights when steel pipes are wet or other risky situations
exist. After the preceding conditions no longer exist, the safety owner and
relevant technical personnel need to check the involved equipment. Operators
can begin working only after safety is confirmed.
● Set a restricted area and prominent signs for working at heights to warn
irrelevant personnel away.
● Set guard rails and warning signs at the edges and openings of the area
involving working at heights to prevent falls.
● Do not pile up scaffolding, springboards, or other objects on the ground under
the area involving working at heights. Do not stay or pass under the area
involving working at heights.
● Carry operation machines and tools properly to prevent equipment damage or
personal injury caused by falling objects.
● Personnel involving working at heights are not allowed to throw objects from
the height to the ground, or vice versa. Objects should be transported by
slings, hanging baskets, highline trolleys, or cranes.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 12

MTS9300A Telecom Power
User Manual 1 Safety Information

● Do not perform operations on the upper and lower layers at the same time. If
unavoidable, install a dedicated protective shelter between the upper and
lower layers or take other protective measures. Do not pile up tools or
materials on the upper layer.
● Dismantle the scaffolding from top down after finishing the job. Do not
dismantle the upper and lower layers at the same time. When removing a
part, ensure that other parts will not collapse.
● Ensure that personnel working at heights strictly comply with the safety
regulations. The Company is not responsible for any accident caused by
violation of the safety regulations on working at heights.
● Behave cautiously when working at heights. Do not rest at heights.

Using Ladders
● Use wooden or insulated ladders when you need to perform live-line working
at heights.
● Platform ladders with protective rails are preferred. Single ladders are not
recommended.
● Before using a ladder, check that it is intact and confirm its load bearing
capacity. Do not overload it.
● Ensure that the ladder is securely positioned and held firm.

● When climbing up the ladder, keep your body stable and your center of
gravity between the side rails, and do not overreach to the sides.
● When a step ladder is used, ensure that the pull ropes are secured.
● If a single ladder is used, the recommended angle for the ladder against the
floor is 75 degrees, as shown in the following figure. A square can be used to
measure the angle.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 13

MTS9300A Telecom Power
User Manual 1 Safety Information

● If a single ladder is used, ensure that the wider end of the ladder is at the
bottom, and take protective measures to prevent the ladder from sliding.
● If a single ladder is used, do not climb higher than the fourth rung of the
ladder from the top.
● If you use a single ladder to climb up to a platform, ensure that the ladder is
at least 1 m higher than the platform.

Hoisting
● Only trained and qualified personnel are allowed to perform hoisting
operations.
● Install temporary warning signs or fences to isolate the hoisting area.
● Ensure that the foundation where hoisting is performed meets the load-
bearing requirements.
● Before hoisting objects, ensure that hoisting tools are firmly secured onto a
fixed object or wall that meets the load-bearing requirements.
● During hoisting, do not stand or walk under the crane or the hoisted objects.
● Do not drag steel ropes and hoisting tools or bump hoisted objects against
hard objects during hoisting.
● Ensure that the angle between two hoisting ropes is no more than 90
degrees, as shown in the following figure.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 14

MTS9300A Telecom Power
User Manual 1 Safety Information

Drilling Holes
● Obtain consent from the customer and contractor before drilling holes.
● Wear protective equipment such as safety goggles and protective gloves when
drilling holes.
● To avoid short circuits or other risks, do not drill holes into buried pipes or
cables.
● When drilling holes, protect the equipment from shavings. After drilling, clean
up any shavings.

1.5 Battery Safety

DANGER

Do not connect the positive and negative poles of a battery together. Otherwise,
the battery may be short-circuited. Battery short circuits can generate high
instantaneous current and releases a large amount of energy, which may cause
battery leakage, smoke, flammable gas release, thermal runaway, fire, or
explosion. To avoid battery short circuits, do not maintain batteries with power on.

DANGER

Do not expose batteries at high temperatures or around heat sources, such as

scorching sunlight, fire sources, transformers, and heaters. Battery overheating
may cause leakage, smoke, flammable gas release, thermal runaway, fire, or
explosion.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 15

MTS9300A Telecom Power
User Manual 1 Safety Information

DANGER

Protect batteries from mechanical vibration, falling, collision, punctures, and

strong impact. Otherwise, the batteries may be damaged or catch fire.

DANGER

To avoid leakage, smoke, flammable gas release, thermal runaway, fire, or

explosion, do not disassemble, alter, or damage batteries, for example, insert
sundries into batteries, squeeze batteries, or immerse batteries in water or other
liquids.

DANGER

There is a risk of fire or explosion if the model of the battery in use or used for
replacement is incorrect. Use a battery of the model recommended by the
manufacturer.

DANGER

Battery electrolyte is toxic and volatile. Do not get contact with leaked liquids or
inhale gases in the case of battery leakage or odor. In such cases, stay away from
the battery and contact professionals immediately. Professionals must wear safety
goggles, rubber gloves, gas masks, and protective clothing, power off the
equipment, remove the battery, and contact technical engineers.

DANGER

A battery is an enclosed system and will not release any gases under normal
operations. If a battery is improperly treated, for example, burnt, needle-pricked,
squeezed, struck by lightning, overcharged, or subject to other adverse conditions
that may cause battery thermal runaway, the battery may be damaged or an
abnormal chemical reaction may occur inside the battery, resulting in electrolyte
leakage or production of gases such as CO and H2. To prevent fire or device
corrosion, ensure that flammable gas is properly exhausted.

DANGER

The gas generated by a burning battery may irritate your eyes, skin, and throat.
Take protective measures promptly.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 16

MTS9300A Telecom Power
User Manual 1 Safety Information

WARNING

Install batteries in a dry area. Do not install them under areas prone to water
leakage, such as air conditioner vents, ventilation vents, feeder windows of the
equipment room, or water pipes. Ensure that no liquid enters the equipment to
prevent faults or short circuits.

WARNING

Before installing and commissioning batteries, prepare fire extinguishing facilities,

such as fire fighting sands and carbon dioxide fire extinguishers, according to
construction standards and regulations. Before putting into operation, ensure that
fire fighting facilities that comply with local laws, regulations are installed.

WARNING

During storage or transportation, or before unpacking, ensure that the packing

cases are intact and the batteries are correctly placed according to the labels on
the packing cases. Do not place a battery upside down or vertically, lay it on one
side, or tilt it. Stack the batteries according to the stacking requirements on the
packing cases. Ensure that the batteries do not fall or get damaged. Otherwise,
they will need to be scrapped.

WARNING

After unpacking batteries, place them in the required direction. Do not place a
battery upside down, lay it on one side, tilt it, or stack it. Ensure that the batteries
do not fall or get damaged. Otherwise, they will need to be scrapped.

WARNING

Tighten the screws on copper bars or cables to the torque specified in this
document. Periodically confirm whether the screws are tightened, check for rust,
corrosion, or other foreign objects, and clean them up if any. Loose screw
connections will result in excessive voltage drops and batteries may catch fire
when the current is high.

WARNING

After batteries are discharged, charge them in time to avoid damage due to
overdischarge.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 17

MTS9300A Telecom Power
User Manual 1 Safety Information

Statement
The Company shall not be liable for any damage or other consequences to
the batteries it provides due to the following reasons:
● Batteries are damaged due to force majeure such as earthquakes, floods,
volcanic eruptions, debris flows, lightning strikes, fires, wars, armed conflicts,
typhoons, hurricanes, tornadoes, and extreme weather conditions.
● Batteries are damaged because the onsite equipment operating environment
or external power parameters do not meet the environment requirements for
normal operation, for example, the actual operating temperature of batteries
is too high or too low, or the power grid is unstable and experiences outages
frequently.
● Batteries are damaged, fall, leak, or crack due to improper operations or
incorrect connection.
● After being installed and connected to the system, the batteries are not
powered on in time due to your reasons, which causes damage to the
batteries due to overdischarge.
● Batteries are damaged because they are not accepted in time due to your
reasons.
● You set battery operating parameters incorrectly.
● Different types of batteries, such as batteries of different vendors, rated
capacity specifications, or aging degrees, are used together, accelerating
capacity attenuation.
● Batteries are frequently overdischarged due to your improper maintenance,
you expand the load capacity without notifying us, or have not fully charge
batteries for a long time.
● You do not perform battery maintenance based on the operation guide, such
as failure to check battery terminals regularly.
● Batteries are damaged because you do not store them in accordance with
storage requirements (for example, in an environment that is damp or prone
to rain).
● Batteries are not charged as required during storage due to your reasons,
resulting in capacity loss or other irreversible damages to the batteries.
● Batteries are damaged due to your or a third party's reasons, for example,
relocating or reinstalling the batteries without complying with the Company's
requirements.
● You change the battery use scenarios without notifying the Company.
● You connect extra loads to the batteries.
● The battery storage period has exceeded the upper limit.
● The battery warranty period has expired.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 18

MTS9300A Telecom Power
User Manual 1 Safety Information

General Requirements

NOTICE

To ensure battery safety and battery management accuracy, use batteries provided
by the Company. The Company is not responsible for any faults of batteries not
provided by it.

● Before installing, operating, and maintaining batteries, read the battery

manufacturer's instructions and comply with their requirements. The safety
precautions specified in this document are highly important and require
special attention. For additional safety precautions, see the instructions
provided by the battery manufacturer.
● Use batteries within the specified temperature range. When the ambient
temperature of the batteries is lower than the allowed range, do not charge
the batteries to prevent internal short circuits caused during low-temperature
charging.
● Do not reversely connect the positive and negative battery terminals.
Otherwise, a battery alarm will be generated and batteries may be damaged.
● Do not short-circuit the battery loop. A short circuit automatically triggers
battery protection. Repeated short circuits may lead to battery faults and
other risks including fire.
● Batteries cannot be connected in series. Connecting them in series will trigger
battery protection and may cause battery damage or other risks including fire.
● Before unpacking batteries, check whether the packaging is intact. Do not use
batteries with damaged packaging. If any damage is found, notify the carrier
and manufacturer immediately.
● In an indoor scenario, you are advised to power on a battery within seven
days after unpacking. If the battery cannot be powered on in time, place it in
a dry indoor environment without corrosive gas.
● In an outdoor scenario, you are advised to power on a battery within 24 hours
after unpacking. If the battery cannot be powered on in time, place it in a dry
indoor environment without corrosive gas.
● Do not use a damaged battery (such as damage caused when a battery is
dropped, bumped, bulged, or dented on the enclosure), because the damage
may cause electrolyte leakage or flammable gas release. In the case of
electrolyte leakage or structural deformation, contact the installer or
professional O&M personnel immediately to remove or replace the battery.
Do not store the damaged battery near other devices or flammable materials
and keep it away from non-professionals.
● Before working on a battery, ensure that there is no irritant or scorched smell
around the battery.
● When installing batteries, do not place installation tools, metal parts, or
sundries on the batteries. After the installation is complete, clean up the
objects on the batteries and the surrounding area.
● The bottom of the battery must be at least 10 cm away from the ground to
prevent water intrusion and battery burning.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 19

MTS9300A Telecom Power
User Manual 1 Safety Information

● If a battery is accidentally exposed to water, do not install it. Move it to a safe

place for isolation and contact technical engineers in a timely manner.
● Check whether the positive and negative battery terminals are grounded
unexpectedly. If so, disconnect the battery terminals from the ground.
● Do not perform welding or grinding work around batteries to prevent fire
caused by electric sparks or arcs.
● If batteries are left unused for a long period of time, store and charge them
according to the battery requirements.
● Do not charge or discharge batteries by using a device that does not comply
with local laws and regulations.
● Keep the battery loop disconnected during installation and maintenance.
● Monitor damaged batteries during storage for signs of smoke, flame,
electrolyte leakage, or heat.
● If a battery is faulty, its surface temperature may be high. Do not touch the
battery to avoid scalds.
● The actual specifications may vary depending on external factors, such as
temperature, transportation, and storage.

Short-Circuit Protection
● When installing and maintaining batteries, wrap the exposed cable terminals
on the batteries with insulation tape.
● Avoid foreign objects (such as conductive objects, screws, and liquids) from
entering a battery, because this may cause short circuits.

Leakage Handling

NOTICE

Electrolyte overflow may damage the equipment. It will corrode metal parts and
boards, and ultimately damage the boards.

Electrolyte is corrosive and can cause irritation and chemical burns. Should you
come into direct contact with the battery electrolyte, do as follows:
● Inhalation: Evacuate from contaminated areas, get fresh air immediately, and
seek immediate medical attention.
● Eye contact: Immediately wash your eyes with water for at least 15 minutes,
do not rub your eyes, and seek immediate medical attention.
● Skin contact: Wash the affected areas immediately with soap and water and
seek immediate medical attention.
● Intake: Seek immediate medical attention.

Recycling
● Dispose of waste batteries in accordance with local laws and regulations. Do
not dispose of batteries as household waste. Improper disposal of batteries
may result in environmental pollution or an explosion.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 20

MTS9300A Telecom Power
User Manual 1 Safety Information

● If a battery leaks or is damaged, contact technical support or a battery

recycling company for disposal.
● If batteries are out of service life, contact a battery recycling company for
disposal.
● Do not expose waste batteries to high temperatures or direct sunlight.
● Do not place waste batteries in environments with high humidity or corrosive
substances.
● Do not use faulty batteries. Contact a battery recycling company to scrap
them as soon as possible to avoid environmental pollution.

1.6 PV Module Safety

DANGER

Before installation and maintenance, cover all PV modules totally using opaque
materials to avoid electric shocks caused by generated currents.

DANGER

Do not focus sunlight on PV modules using a mirror or lens, because this may
damage PV modules and cause personal injury.

WARNING

To install or maintain a high support, set up a support platform and wear a safety
helmet or belt.

General Requirements
● Before installing, operating, and maintaining PV modules, read the
instructions provided by the PV module manufacturer. The safety precautions
specified in this document are highly important and require special attention.
For additional safety precautions, see the instructions provided by the PV
module manufacturer.
● Do not hold junction boxes or power cables to transport PV modules.
● Exercise caution when moving PV modules to avoid collision. Improper
movement and placement may cause the glass plates on PV modules to break
and lose electrical performance, which renders the PV modules useless.
● At least two persons are required to move and install PV modules. Forces
must be applied only to the aluminum frames of the PV modules. Exerting
force on the front or rear surface of the PV modules is prohibited. This may
cause hidden cracks in the PV modules.
● Do not drill holes into, step on, or place heavy objects on PV modules,
because these actions will damage PV modules.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 21

MTS9300A Telecom Power
User Manual 1 Safety Information

● In case of strong wind, do not install PV modules at heights.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 22

MTS9300A Telecom Power
User Manual 2 Product Overview

2 Product Overview

2.1 Overview
The multiple telecommunication system (MTS) is a total solution that provides an
outdoor operating environment, security management, and monitoring networks
for wireless telecom sites. It integrates the outdoor cabinet, temperature control
unit, telecom power supply, monitoring unit, network management system, AC
and DC power distribution units, and surge protection devices. It also provides
sufficient space for housing customer equipment. MTS supports 57 V constant
voltage output when intelligent lithium battery is deployed. It also supports
temperature control capacity expansion, and 57 V indoor blade power systems can
be added. The MTS is a series of efficient, intelligent, and integrated site solutions
applicable to 57 V remote power supply.
The MTS has the following features:
● Highly efficient site
– Battery hibernation
– Temperature control and energy saving
– High-density heat exchange
– High-efficiency rectifiers
● Intelligent site
– IP, GPRS, or in-band networking
– Intelligent temperature control management
● Integrated site
– Modular power distribution design

2.2 Cabinet Description

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 23

MTS9300A Telecom Power
User Manual 2 Product Overview

2.2.1 MTS9302A-HD16A3
Figure 2-1 Appearance

Table 2-1 Cabinet description

Item Description

External ● Cabinet: 1500 mm x 650 mm x 650 mm (excluding the

dimensions (H x W base and the protruding part of the door)
x D) ● Base: 100 mm x 650 mm x 650 mm

Space for batteries Single-layer net space: 330 mm x 610 mm x 590 mm

(H x W x D)

Space for customer 9U

equipment

Cabinet weight < 120 kg (excluding rectifiers and batteries)

Temperature ● Equipment compartment: heat exchanger HXC100P(1)

control mode (1500 W)
● Battery compartment: direct ventilation

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 24

MTS9300A Telecom Power
User Manual 2 Product Overview

Item Description

Cable routing Routed in and out from the bottom

mode

IP rating ● Equipment compartment: IP55

● Battery compartment: IP45

Installation mode Installed on a floor or a rooftop

Optional ● Sensor: smoke sensor, temperature and humidity sensor,

components and water sensor
● Light
● Base cover plate
● Lithium battery support
● Antitheft enclosure frame
● DC output box
● AC output box
● Heater

Power subrack 200 A

Monitor SMU02C

Application ● When lead-acid batteries are installed: It can be used in

environment Class C environments and cannot be used in Class D
environments.
● When lithium batteries are installed: It can be used in
Class B environments and cannot be used in Class C
and Class D environments.

NOTE

● Class B environments refer to indoor environments in which the ambient temperature

and humidity are not controlled and outdoor environments (with simple shielding
measures) where humidity can reach 100%.
● Class C environments refer to sea environments or outdoor land environments (with
simple shielding measures) near pollution sources. If a site is near a pollution source, it
is at most 3.7 km away from salt water, such as the sea and salt lakes, 3 km away from
heavy pollution sources, such as smelteries, coal mines, and thermal power plants, 2 km
away from medium pollution sources, such as chemical, rubber, and galvanization
industries, and 1 km away from light pollution sources, such as packing houses,
tanneries, and boiler rooms.
● Class D environment: It refers to the environment within 500 m away from the ocean.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 25

MTS9300A Telecom Power
User Manual 2 Product Overview

Figure 2-2 Interior

(1) Door status sensor (2) Power subrack (3) Ground bar

(4) Space for the temperature (5) Space for batteries (6) Heat exchanger
and humidity sensor

(7) Space for customer (8) Space for the heater

equipment

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 26

MTS9300A Telecom Power
User Manual 2 Product Overview

2.2.2 MTS9302A-HD16A2
Figure 2-3 Appearance

Table 2-2 Cabinet description

Item Description

External ● Cabinet: 1500 mm x 650 mm x 650 mm (excluding the

dimensions (H x W base and the protruding part of the door)
x D) ● Base: 100 mm x 650 mm x 650 mm

Space for batteries Single-layer net space: 330 mm x 610 mm x 590 mm

(H x W x D)

Space for customer 9U

equipment

Cabinet weight < 120 kg (excluding rectifiers and batteries)

Temperature ● Equipment compartment: heat exchanger HXC70P(1)

control mode (850 W)
● Battery compartment: direct ventilation

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 27

MTS9300A Telecom Power
User Manual 2 Product Overview

Item Description

Cable routing Routed in and out from the bottom

mode

IP rating ● Equipment compartment: IP55

● Battery compartment: IP45

Installation mode Installed on a floor or a rooftop

Optional ● Sensor: smoke sensor, temperature and humidity sensor,

components and water sensor
● Light
● Base cover plate
● Lithium battery support
● Antitheft enclosure frame
● DC output box
● AC output box
● Heater

Power subrack 200 A

Monitor SMU02C

Application ● When lead-acid batteries are installed: It can be used in

environment Class C environments and cannot be used in Class D
environments.
● When lithium batteries are installed: It can be used in
Class B environments and cannot be used in Class C
and Class D environments.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 28

MTS9300A Telecom Power
User Manual 2 Product Overview

Figure 2-4 Interior

(1) Door status sensor (2) Power subrack (3) Ground bar

(4) Space for the temperature (5) Space for batteries (6) Heat exchanger
and humidity sensor

(7) Space for customer (8) Space for the heater

equipment

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 29

MTS9300A Telecom Power
User Manual 2 Product Overview

2.2.3 MTS9302A-HD10A2
Figure 2-5 Appearance

Table 2-3 Cabinet description

Item Description

External ● Cabinet: 900 mm x 650 mm x 650 mm (excluding the

dimensions (H x W base and the protruding part of the door)
x D) ● Base: 100 mm x 650 mm x 650 mm

Space for batteries Single-layer net space: 300 mm x 570 mm x 485 mm (The
(H x W x D) recommended battery depth is less than or equal to 410
mm.)

Space for customer 5U

equipment

Cabinet weight < 80 kg (excluding rectifiers and batteries)

Temperature ● Equipment compartment: heat exchanger HXC70P(1)

control mode (850 W)
● Battery compartment: direct ventilation

Cable routing Routed in and out from the bottom

mode

IP rating ● Equipment compartment: IP55

● Battery compartment: IP45

Installation mode Installed on a floor, against a wall, mounted on a pole or

be stacked on a power supply cabinet.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 30

MTS9300A Telecom Power
User Manual 2 Product Overview

Item Description

Optional ● Sensor: smoke sensor, temperature and humidity sensor,

components and water sensor
● Light
● Base cover plate
● Lithium battery support
● Antitheft enclosure frame (cannot be configured
together with the wall-mounted or pole-mounted
assembly)
● Wall-mounted or pole-mounted assembly
● DC output box
● AC output box

Power subrack 200 A

Monitor SMU02C

Application ● When lead-acid batteries are installed: It can be used in

environment Class C environments and cannot be used in Class D
environments.
● When lithium batteries are installed: It can be used in
Class B environments and cannot be used in Class C
and Class D environments.

Figure 2-6 Interior

(1) Door status sensor (2) Ground bar (3) Space for the temperature
and humidity sensor

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 31

MTS9300A Telecom Power
User Manual 2 Product Overview

(4) Space for batteries (5) Power subrack (6) Heat exchanger

(7) Space for customer

equipment

2.2.4 MTS9302A-HA16A3

Figure 2-7 Appearance

Table 2-4 Cabinet description

Item Description

External dimensions (H ● Cabinet: 1500 mm x 650 mm x 650 mm (excluding

x W x D) the base and the protruding part of the door)
● Base: 100 mm x 650 mm x 650 mm

Space for batteries (H Single-layer net space: 330 mm x 610 mm x 590 mm

x W x D)

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 32

MTS9300A Telecom Power
User Manual 2 Product Overview

Item Description

Space for customer 9U

equipment

Cabinet weight < 135 kg (excluding rectifiers and batteries)

Temperature control ● Equipment compartment: heat exchanger

mode HXC100P(1) (1500 W)
● Battery compartment: air conditioner PC300D

Cable routing mode Routed in and out from the bottom

IP rating IP55

Installation mode Installed on a floor or a rooftop

Optional components ● Sensor: smoke sensor, temperature and humidity

sensor, and water sensor
● Light
● Base cover plate
● Lithium battery support
● Antitheft enclosure frame
● DC output box
● AC output box

Power subrack 200 A

Monitor SMU02C

Application Class C environment, which cannot be used in class D

environment environments

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 33

MTS9300A Telecom Power
User Manual 2 Product Overview

Figure 2-8 Interior

(1) Door status sensor (2) Ground bar (3) Space for the temperature
and humidity sensor

(4) Space for customer (5) Space for batteries (6) Power subrack
equipment

(7) Heat exchanger (8) Air conditioner PC300D

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 34

MTS9300A Telecom Power
User Manual 2 Product Overview

2.2.5 MTS9302A-HA16A2
Figure 2-9 Appearance

Table 2-5 Cabinet description

Item Description

External dimensions ● Cabinet: 1500 mm x 650 mm x 650 mm (excluding

(H x W x D) the base and the protruding part of the door)
● Base: 100 mm x 650 mm x 650 mm

Space for batteries (H Single-layer net space: 330 mm x 610 mm x 590 mm

x W x D)

Space for customer 9U

equipment

Cabinet weight < 135 kg (excluding rectifiers and batteries)

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 35

MTS9300A Telecom Power
User Manual 2 Product Overview

Item Description

Temperature control ● Equipment compartment: heat exchanger

mode HXC70P(1) (850 W)
● Battery compartment: air conditioner PC300D

Cable routing mode Routed in and out from the bottom

IP rating IP55

Installation mode Installed on a floor or a rooftop

Optional components ● Sensor: smoke sensor, temperature and humidity

sensor, and water sensor
● Light
● Base cover plate
● Lithium battery support
● Antitheft enclosure frame
● DC output box
● AC output box

Power subrack 200 A

Monitor SMU02C

Application Class C environment, which cannot be used in class D

environment environments

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 36

MTS9300A Telecom Power
User Manual 2 Product Overview

Figure 2-10 Interior

(1) Door status sensor (2) Ground bar (3) Space for the temperature
and humidity sensor

(4) Space for customer (5) Space for batteries (6) Power subrack
equipment

(7) Heat exchanger (8) Air conditioner PC300D

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 37

MTS9300A Telecom Power
User Manual 2 Product Overview

2.2.6 MTS9303A-HX10A2
Figure 2-11 Appearance

Table 2-6 Cabinet description

Item Description

External ● Cabinet: 900 mm x 650 mm x 650 mm (excluding the

dimensions (H x W base and the protruding part of the door)
x D) ● Base: 100 mm x 650 mm x 650 mm

Space for customer 12 U

equipment

Cabinet weight < 80 kg (excluding rectifiers and batteries)

Temperature Heat exchanger HXC100P(1) (1500 W)

control mode

Cable routing Routed in and out from the bottom

mode

IP rating IP55

Installation mode Installed on a floor, on a rooftop, or against a wall. The

cabinet can be stacked on a battery cabinet.

Optional ● Sensor: smoke sensor, temperature and humidity sensor,

components and water sensor
● Light
● Base cover plate
● Antitheft enclosure frame
● DC output box
● AC output box

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 38

MTS9300A Telecom Power
User Manual 2 Product Overview

Item Description

Power subrack 300 A

Monitor SMU02C

Application Class C environment, which cannot be used in class D

environment environments

Figure 2-12 Interior

(1) Door status sensor (2) Power subrack (3) Ground bar

(4) Space for customer (5) Space for the temperature (6) Heat exchanger
equipment and humidity sensor

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 39

MTS9300A Telecom Power
User Manual 2 Product Overview

2.2.7 MTS9302A-HX10A4
Figure 2-13 Appearance

Table 2-7 Cabinet description

Item Description

External ● Cabinet: 900 mm x 650 mm x 650 mm (excluding the

dimensions (H x W base and the protruding part of the door)
x D) ● Base: 100 mm x 650 mm x 650 mm

Space for customer 12 U

equipment

Cabinet weight < 80 kg (excluding rectifiers and batteries)

Temperature Heat exchanger HXC70P(1) (850 W)

control mode

Cable routing Routed in and out from the bottom

mode

IP rating IP55

Installation mode Installed on a floor, on a rooftop, or against a wall. The

cabinet can be stacked on a battery cabinet.

Optional ● Sensor: smoke sensor, temperature and humidity sensor,

components and water sensor
● Light
● Base cover plate
● Antitheft enclosure frame
● DC output box
● AC output box

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 40

MTS9300A Telecom Power
User Manual 2 Product Overview

Item Description

Power subrack 200 A

Monitor SMU02C

Application Class C environment, which cannot be used in class D

environment environments

Figure 2-14 Interior

(1) Door status sensor (2) Power subrack (3) Ground bar

(4) Space for customer equipment (5) Heat exchanger

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 41

MTS9300A Telecom Power
User Manual 2 Product Overview

2.2.8 MTS9302A-HX10A3
Figure 2-15 Appearance

Table 2-8 Cabinet description

Item Description

External ● Cabinet: 900 mm x 650 mm x 650 mm (excluding the

dimensions (H x W base and the protruding part of the door)
x D) ● Base: 100 mm x 650 mm x 650 mm

Space for customer 12 U

equipment

Cabinet weight < 80 kg (excluding rectifiers and batteries)

Temperature Heat exchanger HXC70P(1) (850 W)

control mode

Cable routing Routed in and out from the bottom

mode

IP rating IP55

Installation mode Installed on a floor, on a rooftop, or against a wall. The

cabinet can be stacked on a battery cabinet.

Optional ● Sensor: smoke sensor, temperature and humidity sensor,

components and water sensor
● Light
● Base cover plate
● Antitheft enclosure frame
● DC output box
● AC output box

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 42

MTS9300A Telecom Power
User Manual 2 Product Overview

Item Description

Power subrack 200 A

Monitor SMU02C

Application Class C environment, which cannot be used in class D

environment environments

Figure 2-16 Interior

(1) Door status sensor (2) Power subrack (3) Ground bar

(4) Space for customer (5) Space for the temperature (6) Heat exchanger
equipment and humidity sensor

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 43

MTS9300A Telecom Power
User Manual 2 Product Overview

2.2.9 MTS9300A-XD10A2

Figure 2-17 Appearance

Table 2-9 Cabinet description

Item Description

External dimensions ● Cabinet: 900 mm x 650 mm x 650 mm (excluding

(H x W x D) the base and the protruding part of the door)
● Base: 100 mm x 650 mm x 650 mm

Space for batteries (H Single-layer net space: 330 mm x 610 mm x 570 mm

x W x D)

Cabinet weight < 55 kg (excluding rectifiers and batteries)

Temperature control Direct ventilation

mode

Cable routing mode Routed in and out from the bottom

IP rating IP45

Installation mode Installed on a floor, on a rooftop, or against a wall. The

cabinet can be stacked on a power supply cabinet.

Optional components ● Base cover plate

● Lithium battery support
● Antitheft enclosure frame

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 44

MTS9300A Telecom Power
User Manual 2 Product Overview

Item Description

Application Class B environment, which cannot be used in class C

environment and D environments

Figure 2-18 Interior

(1) Door status sensor (2) Space for batteries (3) Direct ventilation fan

(4) TCUC/TCUE

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 45

MTS9300A Telecom Power
User Manual 2 Product Overview

2.2.10 MTS9300A-XA10A2
Figure 2-19 Appearance

Table 2-10 Cabinet description

Item Description

External dimensions ● Cabinet: 900 mm x 650 mm x 650 mm (excluding

(H x W x D) the base and the protruding part of the door)
● Base: 100 mm x 650 mm x 650 mm

Space for batteries (H Single-layer net space: 330 mm x 610 mm x 590 mm

x W x D)

Cabinet weight < 55 kg (excluding rectifiers and batteries)

Temperature control Air conditioner PC300D

mode

Cable routing mode Routed in and out from the bottom

IP rating IP55

Installation mode Installed on a floor, on a rooftop, or against a wall. The

cabinet can be stacked on a power supply cabinet.

Optional components ● Base cover plate

● Lithium battery support
● Antitheft enclosure frame

Application Class C environment, which cannot be used in class D

environment environments

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 46

MTS9300A Telecom Power
User Manual 2 Product Overview

Figure 2-20 Interior

(1) Door status sensor (2) Space for batteries (3) Hydrogen vent

(4) Air conditioner PC300D

2.2.11 MTS9300A-HX1001
Figure 2-21 Appearance

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 47

MTS9300A Telecom Power
User Manual 2 Product Overview

Table 2-11 Cabinet description

Item Description

External ● Cabinet: 900 mm x 650 mm x 650 mm (excluding the

dimensions (H x W base and the protruding part of the door)
x D) ● Base: 100 mm x 650 mm x 650 mm

Space for customer 16 U

equipment

Cabinet weight < 55 kg (excluding rectifiers and batteries)

Temperature Heat exchanger

control mode

Cable routing Routed in and out from the bottom

mode

IP rating IP55

Installation mode Installed on a floor, on a rooftop, or against a wall

Optional Base cover plate

components

Application Applicable to class C environments, but not class D

environment environments

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 48

MTS9300A Telecom Power
User Manual 2 Product Overview

Figure 2-22 Interior

(1) TCUC/TCUE (2) Door status sensor (3) Ground bar

(4) Space for customer (5) Heat Exchanger Fans (6) Heat exchanger
equipment

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 49

MTS9300A Telecom Power
User Manual 3 Components

3 Components

3.1 Power Distribution Unit

3.1.1 Power Subrack

Figure 3-1 300 A power subrack

(1) AC SPD (2) AC input circuit breaker (3) LLVD circuit breakers
and terminals

(4) Monitoring module (5) Space for the (6) Space for modules
SMU02C communications expansion
module

(7) RTN+ busbar (8) Battery switch (behind the (9) Battery circuit breakers
cover)

(10) BLVD circuit breakers (11) User interface module

UIM02C

NOTE

Space for the communications expansion module: The NIM01C3 can be installed only on
the upper layer, and the CIM02C can be installed on the upper and lower layers.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 50

MTS9300A Telecom Power
User Manual 3 Components

Table 3-1 Specifications

Item Specifications

AC input system 220/380 V AC three-phase four-wire,

compatible with 220 V AC single-phase

AC power distribution AC input: one 3-pole 63 A circuit breaker

DC power distribution ● BLVD: one 1-pole 63 A circuit breaker, two 1-

pole 32 A circuit breakers, and one 1-pole 16
A circuit breaker
● LLVD: two 1-pole 125 A circuit breakers and
two 1-pole 63 A circuit breakers
● Battery route: two 2-pole 125 A circuit
breakers

Rectifier A maximum of four rectifiers can be

configured.

SMU and UIM SMU02C and UIM02C

Surge protection ● AC surge protection: nominal lightning strike

discharge current 20 kA, maximum lightning
strike discharge current 40 kA, 8/20 µs
● DC surge protection: 10 kA in differential
mode, 20 kA in common mode, 8/20 µs

Figure 3-2 200 A power subrack (three-phase)

(1) AC SPD (2) AC input circuit breaker (3) LLVD circuit breakers
and terminal

(4) Monitoring module (5) Space for the (6) Space for modules
SMU02C communications expansion
module

(7) RTN+ busbar (8) Battery switch (behind the (9) Battery circuit breakers
cover)

(10) BLVD circuit breakers (11) User interface module

UIM02C

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 51

MTS9300A Telecom Power
User Manual 3 Components

Table 3-2 Specifications

Item Specifications

AC input system 220/380 V AC three-phase four-wire,

compatible with 220 V AC single-phase

AC power distribution AC input: one 3-pole 63 A circuit breaker

DC power distribution ● BLVD: two 1-pole 32 A circuit breaker, two

1-pole 16 A circuit breakers, and one 1-pole
10 A circuit breaker
● LLVD: two 1-pole 125 A circuit breakers, two
1-pole 63 A circuit breakers, and two 1-pole
32 A circuit breakers
● Battery route: two 1-pole 125 A circuit
breakers

Rectifier A maximum of four rectifiers can be

configured.

SMU and UIM SMU02C and UIM02C

Surge protection ● AC surge protection: nominal lightning strike

discharge current 20 kA, maximum lightning
strike discharge current 40 kA, 8/20 µs
● DC surge protection: 10 kA in differential
mode, 20 kA in common mode, 8/20 µs

Figure 3-3 200 A power subrack (dual-live wire)

(1) AC output circuit breaker (2) AC SPD (3) AC input circuit breaker
(including interfaces reserved
for indoor blades)

(4) LLVD circuit breakers (5) Monitoring module (6) Space for the
SMU02C communications expansion
module

(7) Space for modules (8) RTN+ busbar (9) Battery switch (behind the
cover)

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 52

MTS9300A Telecom Power
User Manual 3 Components

(10) Battery circuit breakers (11) BLVD circuit breakers (12) User interface module
UIM02C

Table 3-3 Specifications

Item Specifications

AC input system 110 V AC dual–live wire input

AC power distribution ● AC input: one 2-pole 125 A circuit breaker

● AC output: one 2-pole 63 A circuit breaker

DC power ● BLVD: one 1-pole 63 A circuit breaker, two 1-pole 32

distribution A circuit breakers, and one 1-pole 16 A circuit
breaker
● LLVD: two 1-pole 125 A circuit breakers, two 1-pole
63 A circuit breakers, and one 1-pole 32 A circuit
breaker
● Battery route: two 1-pole 125 A circuit breakers

Rectifier A maximum of four rectifiers can be configured.

SMU and UIM SMU02C and UIM02C

Surge protection ● AC surge protection: nominal lightning strike

discharge current 30 kA, maximum lightning strike
discharge current 60 kA, 8/20 µs
● DC surge protection: 10 kA in differential mode, 20
kA in common mode, 8/20 µs

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 53

MTS9300A Telecom Power
User Manual 3 Components

3.1.2 AC and DC Power Distribution Boxes

Figure 3-4 AC power distribution box

(1) AC output circuit breakers and terminals

Table 3-4 Specifications of the AC power distribution box

Item Specifications

AC output circuit Three 1-pole 16 A circuit breakers

breakers

Output voltage 220 V AC

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 54

MTS9300A Telecom Power
User Manual 3 Components

Figure 3-5 DC power distribution box

(1) DC output circuit breakers

Table 3-5 Specifications of the DC power distribution box

Item Specifications

DC output circuit Two 1-pole 63 A circuit breakers and six 1-pole 32 A circuit
breakers breakers

Output voltage 48 V DC

3.2 Rectifier
A rectifier converts AC input power into stable DC power.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 55

MTS9300A Telecom Power
User Manual 3 Components

Figure 3-6 Appearance

(1) Power indicator (2) Alarm indicator (3) Fault indicator

(4) Locking latch (5) Handle

Table 3-6 Indicator description

Indicator Color Status Description

Power Green Steady The rectifier has an AC input.

indicator on

Off The rectifier has no AC input.

The rectifier is faulty.

Blinking The rectifier is being queried.

at 0.5
Hz

Blinking The rectifier is loading an application

at 4 Hz program.

Alarm Yellow Off No alarm is generated.

indicator
Steady ● A warning is generated due to
on ambient overtemperature.
● The rectifier has generated a
protection shutdown alarm due to
ambient overtemperature or
undertemperature.

AC input overvoltage or undervoltage

protection has been triggered.

The rectifier is in hibernation state.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 56

MTS9300A Telecom Power
User Manual 3 Components

Indicator Color Status Description

Blinking The communication between the

at 0.5 rectifier and the external device is
Hz interrupted.

Fault indicator Red Off The rectifier is normal.

Steady The rectifier locks out due to output

on overvoltage.

The rectifier has no output due to an

internal fault.

3.3 (Optional) S4850G1

The S4850G1 is a DC-DC converter that uses maximum power point track (MPPT)
technology. It tracks the highest solar power point based on the output features of
PV modules to maximize the use of solar energy.

Figure 3-7 Appearance

(1) Power indicator (2) Alarm indicator (3) Fault indicator

(4) PV positive input port (5) PV negative input port (6) Air intake vent

(7) Handle

Table 3-7 Indicator description

Indicator Color Normal Abnormal Possible Cause

Power Green Steady on Off There is no DC input.

indicator
The input fuse is faulty.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 57

MTS9300A Telecom Power
User Manual 3 Components

Indicator Color Normal Abnormal Possible Cause

Blinking The S4850G1 is being

queried manually.

Alarm Yellow Off Steady on The S4850G1 is

indicator experiencing
overtemperature.

Output overvoltage alarm

Blinking The communication

between the S4850G1 and
the external is interrupted.

Fault Red Off Steady on The S4850G1 shuts down

indicator due to output
overvoltage.

Fan fault

The S4850G1 shuts down

due to overtemperature.

The S4850G1 generates

no output due to internal
faults.

Blinking Software is being loaded.

3.4 (Optional) PVDU-80A1

Figure 3-8 PVDU-80A1 exterior

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 58

MTS9300A Telecom Power
User Manual 3 Components

Figure 3-9 PVDU-80A1 interior

(1) PV input circuit breakers (2) PV1 (3) PV2

(4) PV3 (5) PV4

Table 3-8 PVDU-80A1 technical specifications

Item Specifications

Dimensions (H x W x 43.6 mm x 482.6 mm x 123 mm (including mounting

D) ears)

Weight ≤ 3.0 kg

Input 60–150 V DC; 4 x 58 A max.

Output 60–150 V DC; 4 x 58 A max.

Installation mode Installed in a 19-inch rack

Cabling mode Routed in and out from the left and right

Maintenance mode Maintained from the front

Operating temperature –20°C to +65°C

Storage temperature –40°C to +70°C

Operating humidity 5%–95% RH (non-condensing)

Altitude 0–4000 m. (When the altitude ranges from 2000 m to

4000 m, high temperature derating applies and the
operating temperature decreases by 1°C for each
additional 200 m.)

IP rating IP20

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 59

MTS9300A Telecom Power
User Manual 3 Components

3.5 Monitoring Module SMU02C

Figure 3-10 SMU02C appearance

(1) Running indicator (2) Minor alarm indicator (3) Major alarm indicator

(4) Buttons (5) USB ports (protected by a (6) RS485/RS232

security protection mechanism) communications port

(7) FE port (8) CAN communications port (9) LCD

Indicators

Table 3-9 Indicator description

Name Color Status Description

Run Green Off The SMU is faulty or has no DC

indicator input.

Blinking The SMU is running properly and

slowly (0.5 communicating with the host
Hz) properly.

Blinking fast The SMU is running properly but fails

(4 Hz) to communicate with the host
properly.

Minor alarm Yellow Off No minor or warning alarm is

indicator generated.

Steady on A minor or warning alarm is

generated.

Major alarm Red Off No critical or major alarm is

indicator generated.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 60

MTS9300A Telecom Power
User Manual 3 Components

Name Color Status Description

Steady on A critical or major alarm is

generated.

Buttons

Table 3-10 Button description

Button Name Description

Up
Press and to scroll through the menus or to
change the value of a parameter.
Down

Cancel Returns to the previous menu without saving the

settings.

Enter ● Enters the main menu from the standby screen.

● Enters a submenu from the main menu.
● Saves menu settings on a submenu.
NOTE
● The LCD screen becomes dark if no button is pressed within 30 seconds.
● You need to log in again if no button is pressed within 1 minute.

● To increase or decrease a parameter value quickly, hold down or during

parameter setting.

● To restart the SMU, hold down and for 10 seconds.

● To increase (or decrease) the LCD backlight, hold down and (or ) for 2
seconds.

USB Ports
You can quickly deploy a site, import and export configuration files, export running
logs, and upgrade software by inserting the USB flash drive that is specially used
for site deployment into the USB port.
After installing the specific WiFi module using the USB port, you can access the
WebUI locally, which facilitates operations.

NOTICE

Using WiFi modules provided by another vendor may cause data loss or function
exception. Consequences arising from this will not be borne by Huawei.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 61

MTS9300A Telecom Power
User Manual 3 Components

Communications Ports

Table 3-11 Communications port description

Communications Communications Communications Usage

Port Parameter Protocol

FE 10/100 M SNMP Connects to a

autonegotiation third-party
management
system.

BIN protocol Connects to a

Huawei NMS.

HTTPS protocol Connects to a

PC and
manages the
SMU through
the WebUI.

TCP-Modbus Adapts to
protocol Huawei TCP-
Modbus
protocol and
connects to a
third-party
NMS.

RS485/RS232 Baud rate: 1200 bit/s, Master/slave Connects to a

2400 bit/s, 4800 protocol Huawei NMS.
bit/s, 9600 bit/s,
14400 bit/s, 19200 YDN protocol Connects to a
bit/s, 115200 bit/s third-party
management
system.

CAN Baud rate: 125 kbit/s CAN protocol Connects to

Huawei
southbound
devices.
NOTE
All these ports are protected by a security mechanism.

Figure 3-11 Communication port pins

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 62

MTS9300A Telecom Power
User Manual 3 Components

Table 3-12 Pin definitions for the FE port

Pin Signal Description

1 TX+ Transmits data over FE

2 TX-

3 RX+ Receives data over FE

6 RX-

4/5/7/8 NA -

Table 3-13 Pin definitions for the RS485/RS232 port

Pin Signal Description

1 TX+ Transmits data over RS485

2 TX-

4 RX+ Receives data over RS485

5 RX-

3 RX232 Receives data over RS232

7 TX232 Transmits data over RS232

6 PGND Connects to the ground

8 NA –

Table 3-14 Description for the CAN port pins

Pin Signal Description

1 RX+ Receives data over RS485

2 RX-

3 NA -

4 TX+ Sends data over RS485

5 TX-

6 NA -

7 CANH CAN high level signal

8 CANL CAN low level signal

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 63

MTS9300A Telecom Power
User Manual 3 Components

3.6 SMU11C
Figure 3-12 SMU11C appearance

(1) Run indicator (2) Minor alarm indicator (3) Major alarm indicator

(4) Wiring terminals (5) Communications port (6) Handle

COM2

(7) DIP switch (8) Position of the SN code (9) Communications port
COM1

Indicator

Table 3-15 Indicator description

Item Color Status Description

Run Green Off The SMU is faulty or has no power

indicator input.

Blinking at The SMU is running properly and

long intervals communicating with the host
(0.5 Hz) properly.

Blinking at The SMU is running properly but fails

short intervals to communicate with the host
(4 Hz) properly.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 64

MTS9300A Telecom Power
User Manual 3 Components

Item Color Status Description

Minor alarm Yellow Off No minor or warning alarm is

indicator generated.

Steady on A minor or warning alarm is

generated.

Major alarm Red Off No critical or major alarm is

indicator generated.

Steady on A critical or major alarm is

generated.

DIP Switch
The dual in-line package switch (DIP switch) is used to set the northbound RS485
communications address.

Figure 3-13 DIP switch

Table 3-16 DIP switch settings

Monitoring Toggle Toggle Toggle Toggle

Address Switch 1 Switch 2 Switch 3 Switch 4

0 OFF OFF OFF OFF

1 ON OFF OFF OFF

2 OFF ON OFF OFF

3 ON ON OFF OFF

4 OFF OFF ON OFF

5 ON OFF ON OFF

6 OFF ON ON OFF

7 ON ON ON OFF

8 OFF OFF OFF ON

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 65

MTS9300A Telecom Power
User Manual 3 Components

Monitoring Toggle Toggle Toggle Toggle

Address Switch 1 Switch 2 Switch 3 Switch 4

9 ON OFF OFF ON

10 OFF ON OFF ON

11 ON ON OFF ON

12 OFF OFF ON ON

13 ON OFF ON ON

14 OFF ON ON ON

15 ON ON ON ON

Wiring Terminals

Figure 3-14 Wiring terminals

Table 3-17 Panel-mounted terminals

Pin Signal Description

1 DI1+ Dry contact input

6 DI1-

2 IO1+ Dry contact input/Dry contact output (When

the pin is used as a dry contact input, the
alarm condition is as follows: the monitoring of
the SMU11C is normal when the dry contact
input is disconnected, and an alarm is
generated when the dry contact input is closed.
When the pin is used as a dry contact output,
the alarm action is as follows: the monitoring
of the SMU11C is normal when the dry contact
output is disconnected, and an alarm is

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 66

MTS9300A Telecom Power
User Manual 3 Components

Pin Signal Description

3 IO1- generated when the dry contact output is

closed.)

4 IO2+ Dry contact input/Dry contact output (When

the pin is used as a dry contact input, the
5 IO2- alarm condition is as follows: the monitoring of
the SMU11C is normal when the dry contact
input is disconnected, and an alarm is
generated when the dry contact input is closed.
When the pin is used as a dry contact output,
the alarm action is as follows: the monitoring
of the SMU11C is normal when the dry contact
output is disconnected, and an alarm is
generated when the dry contact output is
closed.)

7 DI4+ Dry contact input

8 DI4-

9 DI5+ Dry contact input

10 DI5-

Table 3-18 Pin definitions

Pin Signal Description

1 VD1 Midpoint voltage detection port 1

6 VD2 Midpoint voltage detection port 2

2 BTE Battery temperature sensor port

4 ETE Ambient temperature sensor port

7 GAT Door status sensor port

9 CAN+ CAN communications port

10 CAN-

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 67

MTS9300A Telecom Power
User Manual 3 Components

Communications Ports

Table 3-19 Communications port description

Communications Communications Communications Function

Port Parameter Protocol

COM1 Baud rate: 9600 Master/slave Northbound

bit/s, 19200 bit/s, protocol communication
or 115200 bit/s port, connects to a
Huawei NMS.

COM2 Baud rate: 9600 Master/slave Southbound and

bit/s, 19200 bit/s, protocol northbound
or 115200 bit/s multiplexing
communication
port
● Connects to a
Huawei NMS.
● Connects to
Huawei lower-
level devices.
NOTE
All these ports are protected by a security mechanism.

Figure 3-15 Pins in the COM port

Table 3-20 Pin definitions for the COM1 port

Pin Signal Description

1 TX+ Transmits data over RS485.

2 TX-

3 Reserved -

4 RX+ Receives data over RS485.

5 RX-

6 PGND Grounding (PE)

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 68

MTS9300A Telecom Power
User Manual 3 Components

Pin Signal Description

7 Reserved -

8 Reserved -

Table 3-21 Pin definitions for the COM2 port

Pin Signal Description

1 TX+ Transmits data over RS485.

2 TX-

3 12V 12 V output (rated current: 500 mA)

4 RX+ Receives data over RS485.

5 RX-

6 I2C_SCL I2C clock signal

7 I2C_SDA I2C data signal

8 PGND Grounding (PE)

3.7 SMU11D
Figure 3-16 SMU11D appearance

(1) Running indicator (2) Minor Alarm indicator (3) Major alarm indicator

(4) Battery temperature sensor (5) Door check port (6) Communications port
port COM2/CAN

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 69

MTS9300A Telecom Power
User Manual 3 Components

(7) Handle (8) DIP switch (9) SN position

(10) Communications port (11) Dry contacts

COM1

Indicator

Table 3-22 Indicator description

Indicator Color Status Description

Running Green Steady off The SMU is faulty or has no DC

indicator input.

Blinking at The SMU is running and

long intervals communicating with the host
(0.5 Hz) properly.

Blinking at The SMU is running properly but

short intervals does not communicate with the
(4 Hz) host properly.

Minor Alarm Yellow Steady on The communication is normal

indicator and a minor alarm is generated.

Steady off The SMU is running properly.

Major alarm Red Steady on A major alarm is generated.

indicator
Steady off No major or critical alarm is
generated.

DIP Switch
The dual in-line package switch (DIP switch) is used to set the northbound RS485
communications address.

Figure 3-17 DIP switch

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 70

MTS9300A Telecom Power
User Manual 3 Components

Table 3-23 DIP switch settings

Monitoring Toggle Switch 1 Toggle Switch 2 Toggle Switch 3

Address

1 OFF OFF OFF

2 ON OFF OFF

3 OFF ON OFF

4 ON ON OFF

5 OFF OFF ON

6 ON OFF ON

7 OFF ON ON

8 ON ON ON

NOTE

Toggle 4 has not been used and is reserved for hardware.

Panel Mounted Terminals

Figure 3-18 Panel mounted terminals

Table 3-24 Panel mounted terminals

Ports Signals Default State Description

I/O IO1+ DI steady on ALM/DIN Reuse port

IO1–

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 71

MTS9300A Telecom Power
User Manual 3 Components

Ports Signals Default State Description

IO2+

IO2–

GATE GATE– Steady on Door check port

GATE+

BTEMP NTC– - Battery temperature sensor

port
NTC+

Communications Ports

Figure 3-19 Communications ports

Table 3-25 Communications port description

Communications Port Communications Communications Usage

Parameters Protocol

COM1 (northbound Baud rate: 9600 bit/s, Master/slave protocol Connects to a

communications port) 19200 bit/s, 115200 bit/s, Huawei NMS.
auto-negotiation

COM2/CAN COM2 Baud rate: 9600 Modbus protocols Connects to

(southbound bit/s, 19200 bit/s, 115200 Huawei
communication port) bit/s, auto-negotiation southbound
devices.

CAN Baud rate: 125kbit/s CAN protocols Connects to

Huawei
southbound
devices.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 72

MTS9300A Telecom Power
User Manual 3 Components

Communications Port Communications Communications Usage

Parameters Protocol
NOTE
All these ports are protected by a security mechanism.

Figure 3-20 COM port pins

Table 3-26 Pin definitions for the COM1 port

Pin Signals Description

1 TX+ Transmits data over RS485

2 TX–

3 NC -

4 RX+ Receives data over RS485

5 RX–

6/7/8 NC -

Table 3-27 Pin definitions for the COM2 port

Pin Signals Description

1 RX+ Transmits data over RS485

2 RX–

3 NC -

4 TX+ Receives data over RS485

5 TX–

6 NC -

7 CAN_H CAN data +

8 CAN_L CAN data –

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 73

MTS9300A Telecom Power
User Manual 3 Components

3.8 User Interface Module UIM02C

Panel

Figure 3-21 Panel

(1) Communications port (2) Dry contact output ports (3) Dry contact input ports

(4) Sensor ports

Port Description

Table 3-28 Port description

Port Type Silk Screen Remarks

Sensor ports TEM-HUM Ambient temperature and humidity sensor

WATER Water sensor

TEMP1 Temperature sensor 1

TEMP2 Temperature sensor 2

GATE Door status sensor

SMOKE Smoke sensor

BTEMP Battery temperature sensor

Dry contact DIN1 Dry contact input 1

input ports
DIN2 Dry contact input 2

DIN3 Dry contact input 3

DIN4 Dry contact input 4

DIN5 Dry contact input 5

DIN6 Dry contact input 6

Dry contact ALM1 Dry contact output 1

output ports
ALM2 Dry contact output 2

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 74

MTS9300A Telecom Power
User Manual 3 Components

Port Type Silk Screen Remarks

ALM3 Dry contact output 3

ALM4 Dry contact output 4

ALM5 Dry contact output 5

ALM6 Dry contact output 6

ALM7 Dry contact output 7

ALM8 Dry contact output 8

Communications COM RS485

port

Communications Port

Table 3-29 Communications port description

Communications Communications Communications Function

Port Parameter Protocol

COM Baud rate: 1200 Master/slave, Connects to a

bit/s, 2400 bit/s, Modbus and YDN downstream
4800 bit/s, 9600 protocols device, such as
bit/s, 14400 bit/s, the intelligent
19200 bit/s, battery detector
115200 bit/s or intelligent air
conditioner.
NOTE
The COM port is protected by a security mechanism.

Figure 3-22 Pins in the COM port

Table 3-30 COM port pin definitions

Pin Signal Remarks

1 RX+ Receives data over RS485.

2 RX-

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 75

MTS9300A Telecom Power
User Manual 3 Components

Pin Signal Remarks

4 TX+ Transmits data over RS485.

5 TX-

6 PGND Protective ground

3, 7, 8 N/A -

Sensor Ports

Figure 3-23 Pins in sensor ports

Table 3-31 Sensor ports pin definitions

Silk Screen No. Pins

TEM-HUM 1 12V

2 ENV_TEMP

3 12V

4 ENV_HUM

WATER 1 12V

2 WATER

3 GND

4 -

TEMP1 1 GND

2 TEMP1

TEMP2 1 GND

2 TEMP2

GATE 1 GATE+

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 76

MTS9300A Telecom Power
User Manual 3 Components

Silk Screen No. Pins

2 GATE-

SMOKE 1 SMOKE

2 12V

BTEMP 1 GND

2 BTEMP

3.9 Communications Expansion Module CIM02C

The module is used to provide extra RS485/CAN ports for the SMU and supply 12
V power to southbound devices.

Figure 3-24 Panel

(1) COM1 port (2) COM2 port (3) COM3 or COM4 port

(4) 12 V power port (5) COM5 port (6) Handle

Table 3-32 Communications port description

Communications Port Description Communications
Parameter

COM1 ● Supports RS485. Baud rate: 9600 bit/s by

● Supplies 12 V power. default
● Connects to a smart device. Options: 9600 bit/s,
1200 bit/s, 2400 bit/s,
COM2 ● Supports RS485. 4800 bit/s, 14400 bit/s,
● Supplies 12 V power. 19200 bit/s, 115200
bit/s
● Connects to a smart device.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 77

MTS9300A Telecom Power
User Manual 3 Components

Communications Port Description Communications

Parameter

COM3/COM4 COM3 supports RS485 and connects to a

smart device. When COM3 is used to connect
to outdoor devices, reserve only the wires
corresponding to pins 1, 2, 4, and 5 to avoid
surge risks.
COM4 supports RS232 and CAN. RS232 is used
by default, which can be changed to CAN by
using a jumper. For the operation method, see
the appendix. COM4 mainly connects indoor
smart devices. If it is connected to outdoor
smart devices, surge risks may occur.

COM5 ● Supports RS485 and RS232. RS485 is used

by default, which can be changed to RS232
by using a jumper. For the operation
method, see the appendix.
● Connects to an air conditioner.

Figure 3-25 Pin definitions for the COM1, COM2, COM3, or COM4 communication
port

Table 3-33 Pin definitions for the COM1 and COM2 ports
Pin Signal Description

1 RS485_RX+ Receive data over RS485.

2 RS485_RX-

3 12V Power supply

4 RS485_TX+ Transmit data over RS485.

5 RS485_TX-

6 Null -

7 Null -

8 GND Grounding

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 78

MTS9300A Telecom Power
User Manual 3 Components

Table 3-34 Pin definitions for the COM3 and COM4 ports
Pin Signal Description

1 RS485_RX+ Receive data over RS485.

2 RS485_RX-

3 RS232_RXD Receives data over RS232.

4 RS485_TX+ Transmit data over RS485.

5 RS485_TX-

6 GND Grounding

7 CANH/RS232_TXD CAN data, positive/Transmits data over

RS232.

8 CANL CAN data, negative

Table 3-35 COM5 communications port pin definitions

Silk Screen Signal Description

R+/TX RS485+/ RS485 data, positive/Transmits data

RS232_TXD over RS232.

R-/RX RS485-/ RS485 data, negative/Receives data

RS232_RXD over RS232.

GND GND Grounding

3.10 Communications Expansion Module NIM01C3

The communications expansion module is used for 4G communication. It provides
extra RS485/CAN ports for the SMU to connect to southbound communications
equipment.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 79

MTS9300A Telecom Power
User Manual 3 Components

Figure 3-26 Panel

(1) SIM card slots (2 PCS) (2) 4G indicator (3) Alarm indicator

(4) Running indicator (5) ANT antenna port (6) COM1 port

(7) COM2 port (8) COM3/CAN port (9) COM4 port

(10) Handle

Indicators

Table 3-36 Indicator description

Item Color Status Description

4G Green Steady on The dial-up connection is in

indicator the data service state.

Blinking at intervals of 2s A network has been

(on for 0.1s and then off registered.
for 1.9s)

Blinking at intervals of 2s Network search is in progress

(on for 0.1s, off for 0.1s, or no available network is
on for 0.1s, and then off found.
for 1.7s)

Alarm Red Off No alarm is generated.

indicator
Steady on An alarm is generated.

Running Green Off The board is not running

indicator because it is faulty or has no
DC input.

Blinking slowly (0.5 Hz) The board is running and

communicating with the host
properly.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 80

MTS9300A Telecom Power
User Manual 3 Components

Item Color Status Description

Blinking fast (4 Hz) The board is running properly,

but fails to communicate with
the host.

Communications Ports

Table 3-37 Communications port description

Communications Communications Description

Port Parameter

COM1 Baud rate: 9600 bit/s, Supports master/slave and

19200 bit/s, or 115200 Modbus protocols.
bit/s Supplies 12 V power.

COM2 Baud rate: 9600 bit/s, Supports master/slave and

19200 bit/s, or 115200 Modbus protocols.
bit/s Supplies 12 V power.

COM3/CAN Baud rate: 9600 bit/s COM3: Supports master/slave

and Modbus protocols.
CAN: Supports the CAN
protocol.

COM4 Baud rate: 9600 bit/s, Supports the Modbus protocol.

19200 bit/s, or 115200
bit/s

Figure 3-27 Pins in the COM1, COM2, or COM3 port

Table 3-38 Pin definitions for the COM1 and COM2 ports

Pin Signal Description

1 RS485_RX+ Receive data over RS485.

2 RS485_RX-

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 81

MTS9300A Telecom Power
User Manual 3 Components

Pin Signal Description

3 12V Power supply

4 RS485_TX+ Transmit data over RS485.

5 RS485_TX-

6 Null -

7 Null -

8 GND Grounding

Table 3-39 Pin definitions for the COM3/CAN port

Pin Signal Description

1 RS485_RX+ Receive data over RS485.

2 RS485_RX-

3 Null -

4 RS485_TX+ Transmit data over RS485.

5 RS485_TX-

6 GND Grounding

7 CANH CAN bus high level

8 CANL CAN bus low level

Table 3-40 Pin definitions for the COM4 port

Pin Signal Description

R+ RS485+ RS485 data, positive

R- RS485- RS485 data, negative

3.11 EPS100D-N01D1 DC Blade Power Supply

The EPS100D-N01D1 is a blade DC power system that supports 57 V power
system products. It supports 48 V DC input, as well as 48 V DC and 57 V DC
output. It is a reliable power solution for 57 V power system BBU and RXU.
EPS100D-N01D1 also supports 57 V dynamic voltage adjustment. It applies to 57
V power system capacity expansion or reconstruction scenarios.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 82

MTS9300A Telecom Power
User Manual 3 Components

3.11.1 Appearance

Figure 3-28 Appearance

(1) Ground screw (2) DC input terminals (3) SMU11C

(4) BBU wiring ports (5) RXU wiring ports (6) Space for DC-DC module

NOTE

The RXU is a remote radio unit (RRU) or an active antenna unit (AAU).

Table 3-41 PDU specifications

Item EPS100D-N01D1

Input system –48 V DC

Power ● DC output: 5 x 33 A quick-connect terminal

distribution ● DC input: 2 x 100 A terminal
unit (PDU)

3.11.2 Technical Specifications

Table 3-42 Technical specifications

Parameter Parameter Description

Category

Environmental Operating –40°C to +65°C (When the temperature is within 55–65°C, the
condition temperature load needs to be derated to 80%. When the temperature is
within –40°C to –33°C, the system can be normally started
without damage.)

Transport –40°C to +70°C

temperature

Storage –40°C to +70°C

temperature

Operating 5%–95% RH (non-condensing)

humidity

Storage 5%–95% RH (non-condensing)

humidity

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 83

MTS9300A Telecom Power
User Manual 3 Components

Parameter Parameter Description

Category

Altitude 0 m to 4000 m
When the altitude ranges from 2000 m to 4000 m, the
operating temperature decreases by 1°C for each additional
200 m.

Other There should be no conductive dust, corrosive gas, or explosion

requirements hazard.
Dust, corrosive substances, pests, molds, and other indicators
should be controlled in accordance with class 3.1 requirements
in ETSI EN 300 019-1-3 (V2.3.2 or later version).

DC input Default output –53.5 V DC

voltage

Voltage range –40 V DC to –60 V DC

Maximum 150 A
input current

DC output Output voltage –42 V DC to –58 V DC

range of a BBU
port

Output voltage –57 V DC to –60 V DC

range of an
RXU port

Default output –53.5 V DC

voltage of a
BBU port

Default output –57 V DC

voltage of an
RXU port

Maximum 6 kW
output power

Surge DC output 60 V port: differential mode 10 kA, common mode 20 kA, 8/20
protection μs

EMC CE AC port: EN 55032 Class B

specifications
DC port: EN 55032 Class A1

RE EN 55032 Class B

Structure Power supply 43.6 mm x 482.6 mm x 330 mm (H x W x D)

system

Weight < 6 kg (excluding rectifiers)

IP rating IP20

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 84

MTS9300A Telecom Power
User Manual 3 Components

Parameter Parameter Description

Category

Installation Installed in a 19-inch rack, against a wall

mode

Maintenance Maintained from the front

mode

Heat Natural cooling

dissipation
mode
NOTE
1: This is a class A product. In residential areas, this product may cause radio interference; therefore, users may
be required to take appropriate measures.

3.12 EPS100D-N02A1 AC Blade Power Supply

The EPS100D-N02A1 is a blade DC power system that supports 57 V power
system products. It supports AC input and 48 V DC input, as well as 48 V DC and
57 V DC output. It is a reliable power solution for 57 V power system BBU and
RXU. EPS100D-N02A1 also supports 57 V dynamic voltage adjustment and mains
peak clipping. It applies to 57 V power system capacity expansion or
reconstruction scenarios.

3.12.1 Appearance
Figure 3-29 Appearance

(1) Ground screw (2) DC input port (3) Monitoring module

SMU11D

(4) BBU wiring port (5) RXU wiring port (6) Space for installing the DC-
DC conversion module
C6030G1

(7) AC input module AIU03 (8) Space for installing the

rectifier S6050G1

NOTE

The RXU is a remote radio unit (RRU) or an active antenna unit (AAU).

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 85

MTS9300A Telecom Power
User Manual 3 Components

Figure 3-30 AC input module AIU03

(1) Ground screw (2) AC input screw (3) Battery switch

(4) Handle

Table 3-43 PDU specifications

Item EPS100D-N02A1

Power distribution unit ● AC input: 1 x 32 A/3P (M6 OT terminal)

(PDU) ● DC input: 2 x 100 A (dual M6 OT terminals)
● DC output: 5 x 33 A quick-connect terminal

3.12.2 Technical Specifications

Category Parameter Name Description

Environment Operating –40°C to +65°C (When the temperature is within 55°C–

conditions temperature 65°C, the load needs to be derated to 80%. When the
temperature is within –40°C to –33°C, the system can be
normally started without damage.)

Transport –40°C to +70°C

temperature

Storage –40°C to +70°C

temperature

Operating 5%–95% RH (non-condensing)

humidity

Storage humidity 5%–95% RH (non-condensing)

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 86

MTS9300A Telecom Power
User Manual 3 Components

Category Parameter Name Description

Altitude 0 m to 4000 m
(When the altitude ranges from 2000 m to 4000 m, the
operating temperature decreases by 1°C for each
additional 200 m.)

AC and DC Input voltage ● AC: 85–300 V AC, three-phase (also supports single-
power phase)
distribution ● DC: –40 V DC to –60 V DC

Output voltage 60V port: –57 V DC to –63 V DC, default voltage –57 V DC
48 V port: –42 V DC to –58 V DC, default voltage –53.5 V
DC

Input frequency 45–66 Hz

Maximum capacity The maximum load capacity is 6kW

AC input is available: 9 kW (S6050G1 x3 ), The DC input is
available: 6 kW (C6030G1 x 3)

EMC CE AC port: Class B, EN 55032

specifications
DC port: Class A1, EN 55032

RE Class B, EN 55032

Surge AC input Nominal discharge current: 20 kA; maximum discharge

protection current: 40 kA, 8/20 µs

DC output 60V port: differential mode 10 kA, common mode 20 kA,

8/20 μs

Structure Power supply 86.1 mm x 482.6 mm x 330 mm (H x W x D)

system

Weight < 10 kg (excluding modules)

IP rating IP20

Installation mode Installed on a 19-inch rack and mounted on a wall

Maintenance Maintained from the front

mode

Heat dissipation The PDU adopts natural cooling and modules adopt
mode forced-air cooling.
NOTE
1: This is a class A product. In residential areas, this product may cause radio interference; therefore, users may
be required to take appropriate measures.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 87

MTS9300A Telecom Power
User Manual 3 Components

3.13 DC-DC Module (C6030G1)

The C6030G1 is a new-generation non-isolation DC-DC module that supports
bidirectional input and output with two working modes:

Mode 1: The input voltage range of the 48 V port is 40 V DC–60 V DC, and the
output voltage range of the 60 V port is 55 V DC–72 V DC.

Mode 2: The input voltage range of the 60 V port is 57 V DC–72 V DC, and the
output voltage range of the 48 V port is 42 V DC–58 V DC.

The output voltage can be adjusted through a PMU. The DC-DC module provides
overcurrent, overvoltage, and overheat protections.

Figure 3-31 C6030G1 appearance

(1) Indicators (2) Handle

Table 3-44 C6030G1 indicator descriptions

Indicator Color Status Description

Indicator Power Steady on The DC input is available, and the

indicator C6030G1 is operating properly.
(green)
Steady off There is no DC input.

The module is faulty.

Blinking at 0.5 Hz The module is being queried.

Blinking at 4 Hz Application programs are loading.

Alarm Steady on The C6030G1 has generated a pre-

indicator warning due to ambient overtemperature.
(yellow) The C6030G1 has generated a protection
shutdown alarm due to ambient
overtemperature or undertemperature.

Input overvoltage or undervoltage

protection has been triggered.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 88

MTS9300A Telecom Power
User Manual 3 Components

Indicator Color Status Description

The module is shut down.

Blinking at 0.5 Hz The communication between the module

and the outside devices is interrupted.

Fault Steady on The C6030G1 locks out due to output

indicator overvoltage or the C6030G1 is not
(red) properly inserted.

The C6030G1 generates no output due to

internal faults.

3.14 DC Air Conditioner PC300D

Figure 3-32 Appearance

(1) Wiring ports (2) Fans (3) Air exhaust vent

Table 3-45 Technical specifications

Item Specifications

Rated power (L35/ 120 W

L35)

Rated cooling capacity 300 W

(L35/L35)

Heating capacity 300 W

Input voltage –48 V DC (–44 V DC to –57 V DC)

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 89

MTS9300A Telecom Power
User Manual 3 Components

Item Specifications

Operating –40°C to +55°C

temperature

Storage temperature –40°C to +70°C

Alarm reporting Reports alarms over dry contacts. Normal: closed;

faulty: open

Altitude ≤ 4000 m
When the altitude ranges from 2000 m to 4000 m, high
temperature derating applies and the operating
temperature decreases by 1°C for each additional 200
m.

Relative humidity 5%–95% RH

Noise GR487, acoustic pressure level: ≤ 65 dB(A) at 1.5 m

3.15 Top Extended Temperature Control Device

HXC100F
Figure 3-33 Appearance

Table 3-46 Technical specifications

Item Specifications

Dimensions (H x W x 250 mm x 650 mm x 650 mm

D)

Weight < 25 kg

Installation mode Installed on the top of the cabinet

Application Applicable to class C environments, but not to class D

environment environments

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 90

MTS9300A Telecom Power
User Manual 3 Components

Item Specifications

Cooling mode and Heat exchanger, 1000 W (Temperature at the air intake
capacity vent ≤ Ambient temperature + 10°C @ 1000 W heat
consumption, 50°C)

Figure 3-34 Interior

(1) Heat exchanger fans

3.16 TCUC
A temperature control unit C (TCUC) controls the operation of the heat exchanger,
thermoelectric cooler (TEC), and direct ventilation unit and generates an alarm if
an exception occurs.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 91

MTS9300A Telecom Power
User Manual 3 Components

Figure 3-35 TCUC

(1) Power input port (2) Fan ports (3) Boolean value port
(reserved)

(4) Door status sensor port (5) Indicators (6) E-label port (reserved)
(reserved)

(7) COM port (8) Communications port 1 (9) Communications port 2

(10) Temperature sensor port 1 (11) Temperature sensor port 2 (12) Smoke sensor port

(13) Water sensor port (14) Fan ports (15) TEC port

Table 3-47 Indicator description

Silk Screen Color Status Description

RUN Green Steady on Power supply to the board is normal

but no program is running.

Blinking at 0.5 The system is running normally.

Hz

Blinking at 4 Hz Serial port communication is

interrupted or the board is not
registered.

Off The system is not powered on.

ALM Red Steady on Power supply to the board is normal

but no program is running.

Blinking at 0.5 An alarm is generated.

Hz

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 92

MTS9300A Telecom Power
User Manual 3 Components

Silk Screen Color Status Description

Off No alarm is generated.

3.17 TCUE
A temperature control unit E (TCUE) controls the operation of the heat exchanger,
thermoelectric cooler (TEC), and direct ventilation unit and generates an alarm if
an exception occurs.

Figure 3-36 TCUE

(1) Power input port (2) Fan ports (3) Boolean value port
(reserved)

(4) Door status sensor port (5) Indicators (6) Communications port 1
(reserved)

(7) Communications port 2 (8) Temperature sensor port 1 (9) Temperature sensor port 2

(10) Smoke sensor port (11) Fan ports (12) TEC port

Table 3-48 Indicator description

Silk Screen Color Status Description

RUN Green Steady on Power supply to the board is normal

but no program is running.

Blinking at 0.5 The system is running normally.

Hz

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 93

MTS9300A Telecom Power
User Manual 3 Components

Silk Screen Color Status Description

Blinking at 4 Hz Serial port communication is

interrupted or the board is not
registered.

Off The system is not powered on.

ALM Red Steady on Power supply to the board is normal

but no program is running.

Blinking at 0.5 An alarm is generated.

Hz

Off No alarm is generated.

3.18 DC Heater
Figure 3-37 DC heater exterior

(1) Power port (2) Ground screw (3) Indicator

Table 3-49 DC heater specifications

Item Specifications

Dimensions (H x W x D) 43.6 mm x 100 mm x 100 mm

Weight ≤ 1 kg

Operating voltage range 36–75 V DC

Rated operating voltage 48 V DC

Rated power 300 W

Operating temperature range –40°C to +65°C

Startup temperature 5±3°C

Shutdown temperature 15±3°C

Operating humidity range 5% RH–95% RH

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 94

MTS9300A Telecom Power
User Manual 3 Components

Item Specifications

Altitude 0–4000 m. When the altitude ranges from 2000

m to 4000 m, the operating temperature
decreases by 1°C for each additional 200 m.

3.19 AC Heater
A heater assembly unit (HAU) ensures a proper operating temperature for the
equipment inside a cabinet.

Figure 3-38 Appearance

(1) Indicators (2) Alarm dry contact (3) Control dry contact

(4) AC input port

Table 3-50 Indicator description

Silk Color Status Description
Screen

RUN Green Steady on The heater is powered on and detecting its

own status.

Off There is no power input.

ALM Red Off No alarm is generated.

Steady on The heater is faulty and needs to be

replaced.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 95

MTS9300A Telecom Power
User Manual 3 Components

Table 3-51 Heater specifications

Item Specifications

Input voltage 220 V AC single-phase or 110 V AC dual-live wire

Voltage frequency Rated frequency: 50 Hz/60 Hz

Operating temperature –40°C to +65°C

Start/Stop temperature The heater starts at 0°C and stops at 15°C.

Operating humidity 5%–95% RH

Heating power > 500 W

3.20 Electronic Lock

The electronic lock has the following functions:
● Allows you to unlock by using an ID card and the key, or unlock over the
remote NMS.
● Supports remote management of ID card user rights.
● Generates alarms.
● Records logs of swiping cards at the site.

Figure 3-39 Electronic lock

(1) Lock indicator (2) DIP switch

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 96

MTS9300A Telecom Power
User Manual 3 Components

Table 3-52 DIP Switch Principles

Electronic DIP Switch 1 DIP Switch 2 DIP Switch 3 Address
Lock

1 OFF OFF OFF 91

2 ON OFF OFF 92

3 OFF ON OFF 93

4 ON ON OFF 94

5 OFF OFF ON 95

6 ON OFF ON 96

7 OFF ON ON 97

8 ON ON ON 98

Table 3-53 Indicator description

Color Status Status Description

Green Steady on The lock is unlocked and the handle is lifted

up.

Blinking slowly The lock is unlocked, but the handle is not

(0.5 Hz) lifted up.

Blinking fast (4 The lock software is loading. (During

Hz) loading, no lock operation is allowed.)

Red Blinking slowly An unauthorized card is being swiped.

(0.5 Hz)

- Off The lock is properly closed.

Port Definitions

Figure 3-40 Ports on the electronic lock

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 97

MTS9300A Telecom Power
User Manual 3 Components

Table 3-54 Port definitions of the electronic lock

Pin Definitions Description

1 RS485_RX+ RS485 data +

2 RS485_RX- RS485 data -

3 12V Power supply

4 / -

5 / -

6 / -

7 / -

8 GND Ground

3.21 Sensors

3.21.1 Smoke Sensor

Figure 3-41 Appearance 1

(1) Wiring port (2) Base (3) Indicator

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 98

MTS9300A Telecom Power
User Manual 3 Components

Figure 3-42 Appearance 2

(1) Wiring port (2) Base (3) Indicator

3.21.2 Temperature and Humidity Sensor

Figure 3-43 Appearance 1

Figure 3-44 Appearance 2

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 99

MTS9300A Telecom Power
User Manual 3 Components

3.21.3 Water Sensor

Figure 3-45 Appearance

3.21.4 Door Status Sensor

Figure 3-46 Exterior

(1) Switch (2) Magnet

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 100

MTS9300A Telecom Power
User Manual 3 Components

3.21.5 Battery Temperature Sensor

Figure 3-47 Exterior

3.22 Light
Figure 3-48 Appearance

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 101

MTS9300A Telecom Power
User Manual 4 System Maintenance

4 System Maintenance

DANGER

● Wear dedicated protective gears and use insulated tools to avoid electric shocks
or short circuits.
● If the power circuit breaker trips or the fuse is broken, rectify the fault and
power on the device again. Do not directly switch on the circuit breaker or
replace the fuse to avoid device faults or sparks.

4.1 Routine Maintenance

Maintenance personnel perform routine maintenance periodically based on site
requirements. The recommended interval is six months. If any fault is detected,
rectify it in a timely manner. For details about the maintenance and
troubleshooting of lithium batteries, see the corresponding lithium battery
manuals. For details about how to maintain and troubleshoot AC / DC blade
power supplies, see the blade manual.

NOTICE

Do not maintain devices on raining days; otherwise, water may enter and damage
devices.

4.1.1 Routine Maintenance for Cabinets

Maintain the cabinet periodically based on site requirements. The recommended
maintenance interval is six months. If any faults occur, rectify the faults in time.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 102

MTS9300A Telecom Power
User Manual 4 System Maintenance

Table 4-1 CCS routine maintenance checklist

Maintena Check Item Check Repair Condition Solution
nce Item Method

Exterior Check whether the Visual The door lock is Replace the door lock.
door lock is observatio damaged and
damaged. n or cannot be used.
locking
and
unlocking
the door

Check whether the Visual The cabinet is Remove the rust and
cabinet is corroded inspection corroded or rusty. repaint it again.
or rusty.

Check whether a Visual A pole or cabinet is Replace the pole or

pole or cabinet is inspection deformed. cabinet.
deformed.

Check whether the Visual The cabinet surface Use a soft cotton cloth to
cabinet surface is inspection is dirty with oil clean up oil stains or dust
dirty with oil stains stains or dust. on the cabinet surface.
or dust.

Air filter Check whether dust Visual The air filter is Clean the air filter.
accumulates on the inspection dusty.
air filter.

Cabinet Check whether Using a The temperature ● If the temperature is

interior temperature inside thermomet inside the cabinet is below –20°C, take
the cabinet is too er below –20°C or heating measures.
high or low. above +50°C. ● If the temperature is
above +50°C, take
cooling measures such
as enhancing
ventilation.

Grounding Check whether the Visual The cable Secure the ground point
ground point observatio connecting the or replace the ground
properly connects to n and ground point and cable.
the equipment room using a the equipment
ground bar. tool such room ground bar is
as a damaged or loose.
screwdriver
or wrench

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 103

MTS9300A Telecom Power
User Manual 4 System Maintenance

4.1.2 Routine Maintenance for Temperature Control

Equipment
Table 4-2 CCS routine maintenance checklist
Maintenan Check Item Check Method Clearance Solution
ce Item Condition

Heat Check whether the Disconnect the fan The air intake vent Use a brush to
exchanger air intake vent of power supply, of the external clean the dust on
core the external remove the cover circulation fan, fan the external
circulation fan, fan of the external compartment, or circulation fan, fan
compartment, or circulation fan, and heat exchanger is compartment, and
heat exchanger is check whether dusty. air intake vent of
dusty. there is dust on the heat
the external exchanger.
circulation fan, fan For details, see
compartment, and 4.1.8 Cleaning the
air intake vent of Heat Exchanger
the heat Core.
exchanger.

Fan Check whether Visual inspection The fan is dusty. Clean the dust.
dust accumulates
on the fan.

Check whether the Visual inspection The fan is Replace the fan.
fan is intact, and and listening damaged, the
the rotation speed, vibration is
noise, and abnormal, or the
vibration are in noise is loud.
normal ranges.

Air For details, see the corresponding air conditioner manual.

conditioner Link: Outdoor Temperature Control Unit PC300D User Manual

4.1.3 AC and DC Power Distribution

Table 4-3 AC and DC power distribution maintenance
No. Maintenance Item If... Then...

1 Check whether an indicator ● Red: The SPD is Replace the SPD if it is

on the surge protective damaged due to a damaged.
device (SPD) is red. voltage surge or
lightning strike.
● Green: The SPD is
normal.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 104

MTS9300A Telecom Power
User Manual 4 System Maintenance

No. Maintenance Item If... Then...

2 Check the SPD circuit ● OFF: A voltage surge or 1. Replace the circuit
breaker status. lightning strike has breaker if it is damaged,
occurred. replace it
● ON: The SPD is normal. 2. Turn on the circuit
breaker if the SPD is
intact.

3 Check for AC input ● AC input power cables 1. Replace AC input power

undervoltage. have a large voltage cables with shorter or
drop. thicker cables.
● AC input power cables 2. Connect AC input power
are in poor contact. cables securely.
● The mains voltage is too 3. Provide the voltage data
low. to the power supplier.

4 Check for AC input The mains voltage is too Provide the voltage data to
overvoltage. high. the power supplier.

5 Check whether the AC input ● AC input power cables 1. Check and rectify the
voltage is open-phase. are in poor contact, cables.
short-circuited, or 2. Provide the open-phase
damaged. data to the power
● The mains supply has supplier.
failed.

6 Check whether a DC output ● Load overcurrent occurs. Rectify any overcurrent or

circuit breaker is OFF and a ● Load short-circuit short circuit. Turn on the
fuse is blown. occurs. circuit breaker or replace
the fuse.

7 Check for DC busbar A rectifier is abnormal. Replace the abnormal

overvoltage. rectifier.

8 Check for DC busbar ● The AC power supply 1. Resume the AC power

undervoltage. has failed. supply.
● The system is 2. Check the load status
overloaded. and rectify faults if any.
● A rectifier is abnormal. 3. Replace the abnormal
rectifier.

9 Check whether the ● The DC busbar is loose 1. Check and secure cabinet
temperature of a DC busbar or in poor contact. busbar connections.
working at room ● The system is 2. Check the load status
temperature exceeds 95°C. overloaded. and rectify faults if any.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 105

MTS9300A Telecom Power
User Manual 4 System Maintenance

4.1.4 Rectifier
Table 4-4 Rectifier maintenance
No. Maintenance Item Possible Fault Cause Suggestion

1 Check the green indicator Off: 1. Check the rectifier AC

status (normal: steady on). ● There is no AC input. input.
● The rectifier is faulty. 2. Replace the rectifier.

2 Check the yellow indicator Steady on: 1. Check the ambient

status (normal: off). ● Because the ambient temperature status, and
temperature is high, the clean the cabinet air
rectifier power is limited. channel.
● Because the ambient 2. Rectify faults in the
temperature exceeds the indoor temperature
upper or lower threshold, control system.
the rectifier shuts down 3. Check the AC input
for protection. voltage.
● AC input over/ 4. The rectifier is in
undervoltage protection hibernation. No action is
is triggered. required.
● The rectifier is in
hibernation.

Blinking: 1. Check that the rectifier

● The rectifier communications cable is
communication has failed securely connected.
● The rectifier is faulty. 2. Replace the rectifier.

3 Check the red indicator Steady on: 1. Check that the cabinet is
status (normal: off). ● The rectifier is latched off not connected to an
due to output external DC power source
overvoltage. that has a voltage of
greater than 58.5 V DC.
● The rectifier is faulty.
2. Check that the rectifier
output voltage is within
58.5 V DC.
3. Replace the rectifier.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 106

MTS9300A Telecom Power
User Manual 4 System Maintenance

4.1.5 Monitoring Unit

Table 4-5 SMU maintenance
No. Maintenance Possible Cause Suggestion
Item

1 Check the green ● Off: There is no DC 1. Check that the DC input power cable is
indicator status. input. securely connected.
● Off: The SMU is faulty. 2. Check that the communications cable
is securely connected.
3. Replace the SMU.

2 Check the yellow ● Steady on: A minor 1. Check related components based on
indicator status. alarm or warning is alarms.
generated. 2. Replace the SMU.
● Steady on: The SMU is
faulty.

3 Check the red ● Steady on: A critical or 1. Check related components based on
indicator status. major alarm is alarms.
generated. 2. Replace the SMU.
● Steady on: The SMU is
faulty.

4 Check the LCD ● The LCD cable is loose. 1. Check that the LCD cable is securely
display status. ● The SMU is faulty. connected.
2. Replace the SMU.

5 Check that the ● The communications 1. Check that the communications cable
SMU can cable is loose. is securely connected.
communicate ● Networking parameters 2. Check that networking parameters are
with the NMS. are not correctly set. correctly set.

4.1.6 Parameters on the SMU

Table 4-6 SMU parameter maintenance
No. Maintenance Item Possible Fault Cause Suggestion

1 Check whether the ● Parameters are set Set battery parameters

displayed battery capacity incorrectly. again.
and number of battery ● The number of batteries
strings are the same as the is changed, or batteries
actual data. are replaced.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 107

MTS9300A Telecom Power
User Manual 4 System Maintenance

No. Maintenance Item Possible Fault Cause Suggestion

2 Check Charge Current N/A Change the value as

Limit Coefficient. The required. Otherwise, retain
value is typically 0.15C10 0.15C10.
and adjustable.

3 Check whether the ● The battery temperature 1. Replace the battery

displayed battery sensor is faulty. temperature sensor.
temperature is the same as ● The SMU is faulty. 2. Replace the SMU.
the actual temperature.

4 Check whether the ● Battery current detection 1. Check that the current
displayed total load current fault. monitoring cable is
is the same as the actual ● The SMU is faulty. securely connected.
current measured by a 2. Replace the SMU.
clamp meter.

5 Check whether the ● The current monitoring 1. Check that the current
displayed battery charge cable is loose. monitoring cable is
current is the same as the ● The SMU is faulty. securely connected.
actual current measured by 2. Replace the SMU.
a clamp meter.

6 Check whether the ● The cabinet busbar and 1. Check and secure the
difference between the cables are loose or in cabinet busbar and cable
displayed DC output poor contact. connections.
voltage and the measured ● The SMU is faulty. 2. Replace the SMU.
DC busbar voltage is less
than 0.5 V DC.

4.1.7 Cables

Table 4-7 Cable maintenance

No. Maintenance Item Possible Fault Cause Suggestion

1 Check whether signal Cables are not properly Bind signal cables and
cables and power cables installed. power cables separately.
are separately bound.

2 Check whether all cables Cables are not properly Bind cables properly.
are bound properly. installed.

3 Check whether the cabinet Cables are not properly Connect the cabinet ground
ground bar is securely installed. bar to the site or equipment
connected to the site or room ground point.
equipment room ground
point.

4 Check whether ground Cables corrode after being Replace rusty cables.
cables are rusty. used for a long time.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 108

MTS9300A Telecom Power
User Manual 4 System Maintenance

No. Maintenance Item Possible Fault Cause Suggestion

5 Check whether the DC RTN The DC RTN+ busbar is not Connect the ground cable to
+ busbar is grounded. properly grounded. the DC RTN+ busbar
properly.

6 Check whether cables have ● Cables are too thin. ● Replace the cables with
overheated and are ● Cables are not properly cables of the required
deteriorating. routed. thickness.
● Route the cables properly.

7 Check whether cables are Cables are not properly Replace the cables and
misshapen by metal parts. installed. adjust the cable routing.

8 Check whether cables pass Cables are not properly Adjust the cable routing to
behind the air exhaust installed. prevent cable overheating.
vents of rectifiers.

9 Check whether cable Cable insulation is damaged. Reinsulate the cables with
insulation is damaged. insulation tape.

4.1.8 Cleaning the Heat Exchanger Core

NOTE

Maintain the heat exchanger core periodically based on site requirements. The
recommended maintenance interval is six months. You're advised to maintain it before
summer comes. If any faults occur, rectify the faults in time.

Procedure
Step 1 Connect the ground cable to the ESD wrist strap, and put on the ESD wrist strap
and ESD gloves.
Step 2 Record the connection positions of cables on the UIM02C panel and remove the
cables.
Step 3 Unscrew and remove the UIM02C.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 109

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-1 Removing the UIM02C

Step 4 Disconnect the –48 V power cable from the UIM02C backplane.

Figure 4-2 Disconnecting the –48 V power cable

Step 5 Remove the cover from the external circulation fan.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 110

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-3 Removing the cover from the external circulation fan

Step 6 Use a brush to clean the dust on the external circulation fan, fan compartment,
and air intake vent of the heat exchanger.

Figure 4-4 Cleaning dust

Step 7 Install the cover for the external circulation fan. You're advised to tighten the
screws in the sequence shown in the figure.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 111

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-5 Installing the cover for the external circulation fan

Step 8 Connect the –48 V power cable to the UIM02C backplane.

Step 9 Push the UIM02C in place and tighten the screws.

Step 10 Connect cables to the UIM02C panel based on the recorded cable connection
positions.

Step 11 Disconnect the ground cable of the ESD wrist strap, and remove the ESD wrist
strap and ESD gloves.
NOTE

After the system is powered on, you need to check whether the fans work properly.

----End

4.2 Identifying Component Faults

When an alarm is generated, record the alarm ID and handle the alarm by
referring to the SMU Online Alarm Help.

4.2.1 Identifying Rectifier Faults

The following lists the rectifier faults

● The AC input and slot connector are normal, but the Fault indicator (red) is
steady on or all indicators are off.
● The slot connector and SMU are normal, but the Alarm indicator (yellow) still
blinks after the rectifier is reinstalled.
● The AC input and SMU are normal, but the SMU cannot control the rectifier.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 112

MTS9300A Telecom Power
User Manual 4 System Maintenance

4.2.2 Identifying SSU Faults

If any of the following occurs, the SSU is faulty:
● The PV input and slot connector are normal, but the SSU indicator (red) is
steady on or all indicators are off.
● The slot connector and SMU are normal, but the yellow indicator still blinks
after the SSU is reseated.
● The PV input and SMU are normal, but the SMU cannot control the SSU.

4.2.3 Identifying AC SPD Faults

Check the color of the AC SPD indication window. Green indicates that the AC SPD
is normal. Red indicates the AC SPD is faulty.

4.2.4 Identifying Circuit Breaker Faults

The following lists the circuit breaker faults:
● The circuit breaker cannot be switched to ON/OFF after the short circuit fault
for its end circuit is rectified.
● When the circuit breaker is switched to ON and its input voltage is normal,
the voltage between the two ends of the circuit breaker exceeds 1 V.
● The input voltage is normal, but the resistance between both ends of the
circuit breaker is less than 1 kΩ when the circuit breaker is OFF.

4.2.5 Identifying SMU Faults

The following lists the SMU faults:
● The DC output is normal but the green indicator on the SMU is off.
● The SMU breaks down or cannot be started. Its LCD has abnormal display or
buttons cannot be operated.
● With alarm reporting enabled, the SMU does not report alarms when the
power system is faulty.
● The SMU reports an alarm whereas the power system does not experience the
fault.
● The SMU fails to communicate with the connected lower-level devices even
though the communications cables are correctly connected.
● Communication between the SMU and all rectifiers fails even though the
rectifiers and the communications cables are normal.
● The SMU cannot monitor AC or DC power distribution when communications
cables are intact and AC and DC power distribution is normal.
● Parameters cannot be set or running information cannot be viewed on the
SMU.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 113

MTS9300A Telecom Power
User Manual 4 System Maintenance

4.3 Components Replacement

NOTICE

● Ensure that loads are powered on during replacement. For example, keep the
circuit breakers for primary loads ON, and do not disconnect both the battery
input and AC input from the loads.
● Obtain prior written consent from the customer if load disconnection is
required.
● Rectifiers and the SMU are hot-swappable.

4.3.1 Replacing a Rectifier

Prerequisites
● You have obtained a pair of protective gloves and the cabinet door key.
● The new rectifier is intact.

CAUTION

Protect yourself from being burnt when moving the rectifier because the rectifier
has a high temperature.

Procedure
Step 1 Put on protective gloves.

Step 2 Push the locking latch at the right side of the panel towards the left.

Step 3 Gently draw the handle outwards, and then remove the rectifier from the subrack.

Figure 4-6 Removing a rectifier

Step 4 Push the locking latch on the new rectifier towards the left, and pull out the
handle.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 114

MTS9300A Telecom Power
User Manual 4 System Maintenance

Step 5 Place the new rectifier at the entry to the correct slot.

Step 6 Gently slide the converter into the slot along guide rails until it is engaged. Close
the handle, and push the locking latch towards the right to lock the handle.

Figure 4-7 Installing a rectifier

Step 7 Take off protective gloves.

----End

Follow-up Procedure
Pack the removed component, and return it to local warehouse.

4.3.2 Replacing an S4850G1

Prerequisites
● Protective gloves, the cabinet door key, and a maintenance tool kit are
available.
● The new SSU is intact.

CAUTION

To prevent burns, exercise caution when removing an operating SSU because its
surface temperature is high.

Procedure
Step 1 Wear protective gloves.

Step 2 Switch off the circuit breaker on the PVDU, disconnect cables from the SSU, and
label the cables.

Step 3 Push the locking latch on the right side of the SSU panel leftwards.

Step 4 Gently pull out the handle to unlock the SSU, and remove the SSU from the
subrack.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 115

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-8 Pulling out the old SSU

Step 5 Push the locking latch on the new SSU leftwards, and pull out the handle.

Step 6 Place the SSU in the correct slot.

Step 7 Gently push the module along the guide rails until it is in position, close the
handle, and flip the locking latch rightwards to lock the handle.

Figure 4-9 Installing the new SSU

CAUTION

Do not connect the positive and negative DC input cables reversely.

Step 8 Connect the cables to the new SSU based on the recorded information, and switch
on the circuit breaker on the PVDU.

Step 9 Remove the protective gloves.

----End

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 116

MTS9300A Telecom Power
User Manual 4 System Maintenance

Follow-up Procedure
Pack the removed component and send it to the local warehouse.

4.3.3 Replacing a PVDU-80A1

Prerequisites
● The protective gloves, Phillips screwdriver, and key to the cabinet door are
available.
● The new PVDU-80A1 is intact.
NOTE

A PVDU-80A1 needs to be replaced if it is faulty and cannot be repaired immediately.

You only need to disconnect the power supply to the PVDU-80A1, instead of the AC
input to the system.

Procedure
Step 1 Wear protective gloves.

Step 2 Record the connection positions of cables on the PVDU-80A1 and remove the
cables.

Step 3 Remove the faulty PVDU-80A1.

Step 4 Install the new PVDU-80A1.

Figure 4-10 Installing a PVDU-80A1

Step 5 Reconnect the cables to the PVDU-80A1 based on the recorded information.

Step 6 Remove the protective gloves.

----End

Follow-up Procedure
Pack the removed component and send it to the local warehouse.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 117

MTS9300A Telecom Power
User Manual 4 System Maintenance

4.3.4 Replacing an AC SPD Module

Prerequisites
● You have obtained an ESD wrist strap or a pair of ESD gloves, an ESD box or
bag, and the cabinet door key.
● The new AC SPD module is intact and has the same specifications as the old
one.

DANGER

Do not replace an AC SPD module during a thunderstorm.

Procedure
Step 1 Connect the ground cable to the ESD wrist strap and wear the ESD wrist strap and
ESD gloves

Step 2 Hold down the faulty AC SPD module and pull it out.

Step 3 Install a new AC SPD module.

Figure 4-11 Replacing an AC SPD module

Step 4 Disconnect the ground cable from the ESD wrist strap and take off the ESD wrist
strap and ESD gloves.

----End

Follow-up Procedure
Check that the alarm for the AC SPD is cleared.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 118

MTS9300A Telecom Power
User Manual 4 System Maintenance

4.3.5 Replacing a Circuit Breaker

Prerequisites

DANGER

When replacing an AC circuit breaker, switch off the upstream input circuit
breaker. After the replacement is complete, switch on the upstream input circuit
breaker.

● The cabinet door key, insulation tape, and required tools are available.
● The new circuit breaker is intact and has the same specifications as the
original one.

Procedure
Step 1 Unscrew and remove the cover before the circuit breaker.
Step 2 Switch off the circuit breaker that is to be replaced.
Step 3 Record positions where the cables and signal cable terminals connect to the circuit
breaker.
Step 4 Loosen the screw that secures the upper port of the circuit breaker by using a
Phillips screwdriver, and remove the power cable and signal cable terminals. Wrap
the cable and terminals by using the insulation tape to prevent hazards.
Step 5 Loosen the screw that secures the lower port of the circuit breaker by using a
Phillips screwdriver, and loosen the buckle at the circuit breaker base by using an
insulated flat-head screwdriver.
Step 6 Remove the circuit breaker from the guide rail.

Figure 4-12 Removing the circuit breaker

Step 7 Switch off the new circuit breaker. Press the buckle at the circuit breaker base by
using an insulated flat-head screwdriver and install the new circuit breaker. Then
loosen the buckle and secure the circuit breaker to the guide rail.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 119

MTS9300A Telecom Power
User Manual 4 System Maintenance

Step 8 Tighten the screw that secures the lower port of the circuit breaker.

Step 9 Remove the insulation tape from the output power cable and signal cable
terminals. Then connect the power cable and signal cable terminals to the upper
port of the circuit breaker and tighten the screw.

Step 10 Switch on the circuit breaker.

Figure 4-13 Installing the circuit breaker

Step 11 Place the cover before the circuit breaker, and tighten the screws.

----End

Follow-up Procedure
Pack the removed component and send it to the local warehouse.

4.3.6 Replacing an SMU02C

Prerequisites
● An ESD wrist strap, ESD gloves, ESD box or bag, cabinet door key, and
required tools are available.
● The new SMU is intact.

Procedure
Step 1 Connect the ground cable of the ESD wrist strap, and wear the ESD wrist strap and
ESD gloves.
NOTE

Record the software version of the old SMU. If the old SMU is damaged and version
information cannot be viewed, send the bar codes of the old SMU and cabinet to technical
support engineers.

Step 2 Disconnect the communications cable from the SMU02C panel and record the
cable information.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 120

MTS9300A Telecom Power
User Manual 4 System Maintenance

Step 3 Push the locking latch leftwards.

Step 4 Pull the handle outwards and remove the SMU02C from the subrack.

Figure 4-14 Removing the SMU02C

Step 5 Place the new SMU02C in the slot, push the locking latch leftwards, and pull out
the handle.

Step 6 Gently push the SMU02C along the guide rails until it is engaged. Close the
handle, and push the locking latch rightwards.

Figure 4-15 Installing the SMU02C

Step 7 Reconnect the communications cable to the SMU02C panel based on the recorded
information.

Step 8 Set SMU02C parameters.

NOTE

After installing the new SMU, power on the SMU and check the software version of the
new SMU. If the software version of the new SMU is earlier than that of the old SMU,
upgrade the software.

Step 9 Disconnect the ground cable of the ESD wrist strap, and remove the ESD wrist
strap and ESD gloves.

----End

Follow-up Procedure
Put the removed component in an ESD box or bag and return it to the local
warehouse.

4.3.7 Replacing an SMU11C

Prerequisites
● An ESD wrist strap, ESD gloves, and ESD box or bag are available.
● The new SMU is intact.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 121

MTS9300A Telecom Power
User Manual 4 System Maintenance

Procedure
Step 1 Connect the ground cable of the ESD wrist strap, and wear the ESD wrist strap and
ESD gloves.
Step 2 Record the cable connection positions on the SMU panel, remove the COM
communications cables, and remove the signal cable terminals.
Step 3 Pull out the handle to remove the SMU from the subrack.

Figure 4-16 Removing the old SMU

Step 4 Record the DIP switch settings on the SMU.

Step 5 Take out the new SMU and set the DIP switch based on the recorded information.
Step 6 Insert the new SMU into the slot and slide it into the subrack along the guide rails.
Step 7 Push the handle of the SMU upwards until it is in position.

Figure 4-17 Installing the new SMU

Step 8 Connect the signal cable terminals and COM communications cables to the panel
of the new SMU based on the recorded information.
Step 9 Disconnect the ground cable of the ESD wrist strap, and remove the ESD wrist
strap and ESD gloves.

----End

Follow-up Procedure
Put the removed component in an ESD box or bag and return it to the local
warehouse.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 122

MTS9300A Telecom Power
User Manual 4 System Maintenance

4.3.8 Replacing an SMU11D

Prerequisites
● An ESD wrist strap, ESD gloves, an ESD box or bag, and required tools are
available.
● The new SMU is intact.

Procedure
Step 1 Connect the ground cable of the ESD wrist strap, and wear the ESD wrist strap and
ESD gloves.

Step 2 Record the cable connection positions on the SMU panel, remove the COM
communications cables, and remove the signal cable terminals.

Step 3 Pull out the handle of the SMU to remove it from the subrack.

Figure 4-18 Removing the old SMU

Step 4 Record the DIP switch settings on the SMU.

Step 5 Take out the new SMU and set the DIP switch based on the recorded information.

Figure 4-19 Installing the new SMU

Step 6 Insert the new SMU into the slot and slide it into the subrack along the guide rails.

Step 7 Push the handle of the SMU upward until it is in position.

Step 8 Connect the signal cable terminals and COM communications cables to the panel
of the new SMU based on the recorded information.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 123

MTS9300A Telecom Power
User Manual 4 System Maintenance

Step 9 Disconnect the ground cable of the ESD wrist strap, and remove the ESD wrist
strap and ESD gloves.

----End

Follow-up Procedure
Put the removed component in an ESD box or bag and return it to the local
warehouse.

4.3.9 Replacing a UIM02C Board

Prerequisites
● An ESD wrist strap, ESD gloves, an ESD box or bag, cabinet door key, and
required tools are available.
● The new UIM02C board is intact.

Procedure
Step 1 Connect the ground cable of the ESD wrist strap, and wear the ESD wrist strap and
ESD gloves.

Step 2 Record the position of signal cables connected to the UIM02C panel, and then
disconnect the signal cables.

Step 3 Unscrew and take out the UIM02C.

Figure 4-20 Taking out the UIM02C

Step 4 Disconnect the –48 V power cable from the UIM02C board.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 124

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-21 Disconnecting the –48 V power cable

(1) –48 V power port

Step 5 Record the connection positions of all cables including cables for internal and
external circulation fans and flat cables on the UIM02C board, and then
disconnect the cables.

Step 6 Remove the UIM02C board.

Figure 4-22 Removing the UIM02C board

Step 7 Take out and install the new UIM02C board.

Step 8 Connect all the cables on the UIM02C board to the new UIM02C based on the
recorded information.

Step 9 Reconnect the –48 V power cable to the UIM02C board.

Step 10 Push the UIM02C in place and tighten the screws.

Step 11 Reconnect signal cables to the new UIM02C panel based on the recorded
information.

Step 12 Disconnect the ground cable of the ESD wrist strap, and remove the ESD wrist
strap and ESD gloves.

----End

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 125

MTS9300A Telecom Power
User Manual 4 System Maintenance

Follow-up Procedure
Put the removed component in an ESD box or bag and return it to the local
warehouse.

4.3.10 Replacing a CIM02C

Prerequisites
● An ESD wrist strap, ESD gloves, ESD box or bag, cabinet door key, and
required tools are available.
● The new CIM02C is intact.

Procedure
Step 1 Connect the ground cable to the ESD wrist strap, and put on the ESD wrist strap
and ESD gloves.
Step 2 Note where cables are connected to the CIM02C panel. Record these positions and
disconnect the cables.
Step 3 Loosen the screws on both sides of the CIM02C panel.
Step 4 Pull the handle rightwards and take out the CIM02C.

Figure 4-23 Removing the CIM02C

Step 5 Place the new CIM02C into the correct slot in the subrack, and push the CIM02C
until its front panel is flush with the front panel of the subrack.
Step 6 Push the handle inwards until it is engaged, and then tighten the screws.

Figure 4-24 Installing the CIM02C

Step 7 Reconnect the cables to the new CIM02C panel based on the information you
recorded.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 126

MTS9300A Telecom Power
User Manual 4 System Maintenance

Step 8 Disconnect the ground cable from the ESD wrist strap, and remove the ESD wrist
strap and ESD gloves.

----End

Follow-up Procedure
Put the replaced component in an ESD box or bag and return it to the local
warehouse.

4.3.11 Replacing an NIM01C3

Prerequisites
● An ESD wrist strap, ESD gloves, ESD box or bag, cabinet door key, and
required tools are available.
● The new NIM01C3 is intact.

Procedure
Step 1 Connect the ground cable to the ESD wrist strap, and put on the ESD wrist strap
and ESD gloves.

Step 2 Record all cable connection positions on the communications expansion module
and disconnect the cables.

Step 3 Loosen the screws on both sides of the communications expansion module.

Step 4 Pull the handle rightwards and remove the communications expansion module.

Figure 4-25 Removing a communications expansion module

Step 5 Remove the SIM card from the SIM card slot, and insert the new communications
expansion module. Skip this step if no SIM card is installed.

Step 6 Place the new NIM01C3 in the corresponding slot of the monitoring unit subrack,
and push the NIM01C3 until its front panel is flush with the front panel of the
monitoring unit subrack.

Step 7 Push the handle inwards until it is engaged, and then tighten the screws.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 127

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-26 Installing a communications expansion module

Step 8 Reconnect cables to the panel of the new communications expansion module
based on the recorded information.
Step 9 Disconnect the ground cable from the ESD wrist strap, and remove the ESD wrist
strap and ESD gloves.

----End

Follow-up Procedure
Put the replaced component in an ESD box or bag and return it to the local
warehouse.

4.3.12 Replacing Heat Exchanger Fans

Prerequisites
● Required tools and the key of the cabinet door are available.
● The new fans are intact.

Procedure
Step 1 Connect the ground cable to the ESD wrist strap, and put on the ESD wrist strap
and ESD gloves.
Step 2 Record the connection positions of cables on the UIM02C panel and remove the
cables.
Step 3 Unscrew and remove the UIM02C.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 128

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-27 Removing the UIM02C

Step 4 Disconnect the –48 V power cable from the UIM02C backplane.
Step 5 Remove the wiring terminal between the UIM02C and the fan.
Step 6 Flip the buckle inward and take out the fan assemblies.
Step 7 Remove the fan to be replaced.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 129

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-28 Replacing a fan

Step 8 Install a new fan.

Figure 4-29 Installing a fan

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 130

MTS9300A Telecom Power
User Manual 4 System Maintenance

Step 9 Reinstall the fan assemblies.

Step 10 Connect the wiring terminal between the UIM02C and the fan.

Step 11 Connect the –48 V power cable to the UIM02C backplane.

Step 12 Push the UIM02C in place and tighten the screws.

Step 13 Connect cables to the UIM02C panel based on the recorded cable connection
positions.

Step 14 Disconnect the ground cable of the ESD wrist strap, and remove the ESD wrist
strap and ESD gloves.
NOTE

After the system is powered on, you need to check whether the fans work properly.

----End

4.3.13 Replacing a TCUC Control Board (Horizontal

installation)

Prerequisites
● An ESD wrist strap, a pair of ESD gloves, an ESD box or bag, a Phillips
screwdriver, and the cabinet door key are available.
● The new TCUC control board is intact.

Procedure
Step 1 Connect the ground cable of the ESD wrist strap, and wear the ESD wrist strap and
ESD gloves.

Step 2 Switch off the upstream power input circuit breaker for the TCUC, record the cable
connections on the TCUC, and disconnect the cables.

Step 3 Remove the TCUC.

Figure 4-30 Removing a TCUC

Step 4 Remove the faulty TCUC control board.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 131

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-31 Removing the faulty TCUC control board

Step 5 Record the cable connection positions on the TCUC control board and disconnect
the cables.
Step 6 Record the information about the jumper caps on the TCUC control board.

Figure 4-32 Position of the jumper on the TCUC control board

Step 7 Adjust the positions of the jumper caps on the new TCUC control board based on
the recorded information.
Step 8 Connect cables to the new TCUC control board based on the recorded cable
positions.
Step 9 Install the new TCUC control board in the TCUC.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 132

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-33 Installing the new TCUC control board

Step 10 Reinstall the TCUC.

Figure 4-34 Reinstalling the TCUC

Step 11 Connect cables to the TCUC based on the recorded cable positions.
Step 12 Switch on the upstream power input circuit breaker for the TCUC.
Step 13 Disconnect the ground cable of the ESD wrist strap, and remove the ESD wrist
strap and ESD gloves.

----End

Follow-up Procedure
Put the removed component in an ESD box or bag and return it to the local
warehouse.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 133

MTS9300A Telecom Power
User Manual 4 System Maintenance

4.3.14 Replacing a TCUC Control Board

Prerequisites
● An ESD wrist strap, a pair of ESD gloves, an ESD box or bag, a Phillips
screwdriver, and the cabinet door key are available.
● The new TCUC control board is intact.

Procedure
Step 1 Connect the ground cable of the ESD wrist strap, and wear the ESD wrist strap and
ESD gloves.
Step 2 Switch off the upstream power input circuit breaker for the TCUC, record the cable
connections on the TCUC, and disconnect the cables.
Step 3 Remove the TCUC fastening bracker.

Figure 4-35 Removing the TCUC fastening bracker

Step 4 Remove the TCUC.

Figure 4-36 Removing a TCUC

Step 5 Remove the faulty TCUC control board.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 134

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-37 Removing the faulty TCUC control board

Step 6 Record the cable connection positions on the TCUC control board and disconnect
the cables.

Step 7 Record the information about the jumper caps on the TCUC control board.

Figure 4-38 Position of the jumper on the TCUC control board

Step 8 Adjust the positions of the jumper caps on the new TCUC control board based on
the recorded information.

Step 9 Connect cables to the new TCUC control board based on the recorded cable
positions.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 135

MTS9300A Telecom Power
User Manual 4 System Maintenance

Step 10 Install the new TCUC control board in the TCUC.

Figure 4-39 Installing the new TCUC control board

Step 11 Reinstall the TCUC.

Figure 4-40 Reinstalling the TCUC

Step 12 Reinstall the TCUC fastening bracker.

Figure 4-41 Reinstalling the TCUC fastening bracker

Step 13 Connect cables to the TCUC based on the recorded cable positions.

Step 14 Switch on the upstream power input circuit breaker for the TCUC.

Step 15 Disconnect the ground cable of the ESD wrist strap, and remove the ESD wrist
strap and ESD gloves.

----End

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 136

MTS9300A Telecom Power
User Manual 4 System Maintenance

Follow-up Procedure
Put the removed component in an ESD box or bag and return it to the local
warehouse.

4.3.15 Replacing a TCUE Control Board (Horizontal

installation)
Prerequisites
● An ESD wrist strap, a pair of ESD gloves, an ESD box or bag, a Phillips
screwdriver, and the cabinet door key are available.
● The new TCUE control board is intact.

Procedure
Step 1 Connect the ground cable of the ESD wrist strap, and wear the ESD wrist strap and
ESD gloves.
Step 2 Switch off the upstream power input circuit breaker for the TCUE, record the cable
connections on the TCUE, and disconnect the cables.
Step 3 Remove the TCUE.

Figure 4-42 Removing a TCUE

Step 4 Remove the faulty TCUE control board.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 137

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-43 Removing the faulty TCUE control board

Step 5 Record the cable connection positions on the TCUE control board and disconnect
the cables.
Step 6 Record the information about the jumper caps on the TCUE control board.

Figure 4-44 Position of the jumper on the TCUE control board

Step 7 Adjust the positions of the jumper caps on the new TCUE control board based on
the recorded information.
Step 8 Connect cables to the new TCUE control board based on the recorded cable
positions.
Step 9 Install the new TCUE control board in the TCUE.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 138

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-45 Installing the new TCUE control board

Step 10 Reinstall the TCUE.

Figure 4-46 Reinstalling the TCUE

Step 11 Connect cables to the TCUE based on the recorded cable positions.

Step 12 Switch on the upstream power input circuit breaker for the TCUE.

Step 13 Disconnect the ground cable of the ESD wrist strap, and remove the ESD wrist
strap and ESD gloves.

----End

Follow-up Procedure
Put the removed component in an ESD box or bag and return it to the local
warehouse.

4.3.16 Replacing a TCUE Control Board

Prerequisites
● An ESD wrist strap, a pair of ESD gloves, an ESD box or bag, a Phillips
screwdriver, and the cabinet door key are available.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 139

MTS9300A Telecom Power
User Manual 4 System Maintenance

● The new TCUE control board is intact.

Procedure
Step 1 Connect the ground cable of the ESD wrist strap, and wear the ESD wrist strap and
ESD gloves.
Step 2 Switch off the upstream power input circuit breaker for the TCUE, record the cable
connections on the TCUE, and disconnect the cables.
Step 3 Remove the TCUE fastening bracker.

Figure 4-47 Removing the TCUE fastening bracker

Step 4 Remove the TCUE.

Figure 4-48 Removing a TCUE

Step 5 Remove the faulty TCUE control board.

Figure 4-49 Removing the faulty TCUE control board

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 140

MTS9300A Telecom Power
User Manual 4 System Maintenance

Step 6 Record the cable connection positions on the TCUE control board and disconnect
the cables.
Step 7 Record the information about the jumper caps on the TCUE control board.

Figure 4-50 Position of the jumper on the TCUE control board

Step 8 Adjust the positions of the jumper caps on the new TCUE control board based on
the recorded information.
Step 9 Connect cables to the new TCUE control board based on the recorded cable
positions.
Step 10 Install the new TCUE control board in the TCUE.

Figure 4-51 Installing the new TCUE control board

Step 11 Reinstall the TCUE.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 141

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-52 Reinstalling the TCUE

Step 12 Reinstall the TCUE fastening bracker.

Figure 4-53 Reinstalling the TCUE fastening bracker

Step 13 Connect cables to the TCUE based on the recorded cable positions.
Step 14 Switch on the upstream power input circuit breaker for the TCUE.
Step 15 Disconnect the ground cable of the ESD wrist strap, and remove the ESD wrist
strap and ESD gloves.
----End

Follow-up Procedure
Put the removed component in an ESD box or bag and return it to the local
warehouse.

4.3.17 Replacing a Smoke Sensor

Prerequisites
● You have obtained an ESD wrist strap, a pair of ESD gloves, an ESD box or
bag, the cabinet door key, and tools.
● The new smoke sensor is intact.

Procedure
Step 1 Connect the ground cable to the ESD wrist strap, and put on the ESD wrist strap
and ESD gloves.
Step 2 Remove the smoke sensor.
1. Remove the connected cables from the smoke sensor.
2. Hold down the button on the smoke sensor and push the smoke sensor in the
OPEN direction.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 142

MTS9300A Telecom Power
User Manual 4 System Maintenance

3. Unscrew the smoke sensor base.

Figure 4-54 Removing the smoke sensor

Step 3 Install a new smoke sensor.

1. Properly place the smoke sensor base and tighten the screws for it.
2. Properly place the new smoke sensor and press and push it in the CLOSE
direction.
3. Reconnect the removed cables to the smoke sensor.

Step 4 Disconnect the ground cable from the ESD wrist strap, and take off the ESD wrist
strap and ESD gloves.

----End

Follow-up Procedure
Pack the removed component and send it to the local warehouse.

4.3.18 Replacing a Temperature and Humidity Sensor

(UIM02C)

Prerequisites
● An ESD wrist strap, ESD box or bag, the cabinet door key, and required tools
are available.
● The new temperature and humidity sensor is intact.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 143

MTS9300A Telecom Power
User Manual 4 System Maintenance

Procedure
Step 1 Connect the ground cable of the ESD wrist strap, and wear the ESD wrist strap and
ESD gloves.
Step 2 Disconnect the temperature and humidity sensor cable from the UIM and record
the port information.

Figure 4-55 Disconnecting the temperature and humidity sensor cable

Step 3 Remove the temperature and humidity sensor.

1. Remove the fastener for the temperature and humidity sensor from the
cabinet.
2. Open the cover of the temperature and humidity sensor.
3. Record the cable connection position and remove the cable.
4. Unscrew and take off the sensor from the fastener.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 144

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-56 Removing a temperature and humidity sensor (type 1)

Figure 4-57 Removing a temperature and humidity sensor (type 2)

Step 4 Install the new temperature and humidity sensor.

1. Uncover the new temperature and humidity sensor and install the sensor on
the fastener.
2. Connect the cable to the new sensor based on the recorded information.
3. Properly place the sensor cover and secure the cover to the sensor.
4. Reinstall the fastener for the temperature and humidity sensor on the rack.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 145

MTS9300A Telecom Power
User Manual 4 System Maintenance

Step 5 Connect the temperature and humidity sensor cable to the UIM.
Step 6 Disconnect the ground cable of the ESD wrist strap, and remove the ESD wrist
strap and ESD gloves.

----End

Follow-up Procedure
Pack the removed component and send it to the local warehouse.

4.3.19 Replacing a Door Status Sensor

Prerequisites
● The cabinet door key and required tools are available.
● The new door status sensor is intact.

Procedure
Step 1 Open the front door and remove the enclosure of the door status sensor.
Step 2 Unscrew and remove the alarm cables and mark the connection positions.
Step 3 Unscrew and remove the door status sensor.

Figure 4-58 Removing a door status sensor

Step 4 Remove the enclosure of the new sensor, and then remove the screws from the
alarm cables.
Step 5 Place the new door status sensor to the installation position and tighten the
screws.
Step 6 Connect the alarm cables in sequence and tighten the screws.
Step 7 Reinstall the enclosure of the door status sensor.

----End

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 146

MTS9300A Telecom Power
User Manual 4 System Maintenance

Follow-up Procedure
Check that the door status alarm is cleared.

4.3.20 Replacing a Battery Temperature Sensor (UIM02C)

Prerequisites
● An ESD wrist strap, ESD box or bag, the cabinet door key, and maintenance
tool kit are available.
● The new battery temperature sensor is intact.

Procedure
Step 1 Connect the ground cable of the ESD wrist strap, and wear the ESD wrist strap and
ESD gloves.
Step 2 Disconnect the battery temperature sensor cable from the UIM and record the
port information.

Figure 4-59 Disconnecting the battery temperature sensor cable

Step 3 Cut off the cable tie of the battery temperature sensor and remove the sensor.

NOTICE

Ensure that the detection probe of the battery temperature sensor is not in
contact with a metal surface.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 147

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-60 Position of the battery temperature sensor

Step 4 Properly place the new battery temperature sensor and bind it securely with a
cable tie.

Step 5 Connect the battery temperature sensor cable to the UIM.

Step 6 Disconnect the ground cable of the ESD wrist strap, and remove the ESD wrist
strap and ESD gloves.

----End

Follow-up Procedure
Pack the removed component and send it to the local warehouse.

4.3.21 Replacing an Electronic Lock

Prerequisites
● You have obtained an ESD wrist strap, a pair of ESD gloves, an ESD box or
bag, the cabinet door key, and tools.
● The new electronic lock is intact.

Procedure
Step 1 Connect the ground cable for the ESD wrist strap, and put on the ESD wrist strap
and ESD gloves.

Step 2 Disconnect the electronic lock cable from the cable connector.

Step 3 Unscrew the electronic lock rotation axis.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 148

MTS9300A Telecom Power
User Manual 4 System Maintenance

Figure 4-61 Unscrewing a rotation axis

Step 4 Unscrew the electronic lock cover, and remove the lock.

Figure 4-62 Removing an electronic lock

(1) Lock (2) Lock cover

Step 5 Record the DIP switch settings of the electronic door lock.
Step 6 Take out a new electronic lock. Set the DIP switch of the electronic door lock
based on the recorded information.

NOTICE

Before powering on the electronic door lock, ensure that the DIP switch settings
are the same as those of the original DIP switch.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 149

MTS9300A Telecom Power
User Manual 4 System Maintenance

Step 7 Remove the other screws from the lock, reinstall the lock on the cabinet door, and
tighten screws on the lock cover.
Step 8 Install screws on the electronic lock rotation axis.
Step 9 Connect the electronic lock cable to the cable connector.
Step 10 Disconnect the ground cable for the ESD wrist strap, and take off the ESD wrist
strap and ESD gloves.

----End

Follow-up Procedure
Pack the removed component and send it to the local warehouse.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 150

MTS9300A Telecom Power
User Manual A Operating Environment

A Operating Environment

Environments subject to atmospheric corrosion can be classified into four

categories:

Table A-1 Application environment description

Category Environment Definition

Class A Controlled environment. Indoor environment where the ambient temperature

and humidity are controlled (including rooms where people live) and the
relative humidity of air is controlled below 65%.

Class B Uncontrolled environment. Indoor environment where the ambient temperature

and humidity are not controlled or outdoor environments (with simple shielding
measures) where the humidity can reach 100%.

Class C Hash environment. Outdoor land environment (with simple shielding measures)
near seas or pollution sources. If a site is near a sea, it is 0.5–3.7 km away from
the sea. If a site is near a pollution source, it is at most 3.7 km away from salt
lakes, 3 km away from heavy pollution sources such as smelteries, coal mines,
and thermal power plants, 2 km away from medium pollution sources such as
chemical, rubber, and galvanization industries, or 1 km away from light
pollution sources such as packing houses, tanneries, and boiler rooms.

Class D Oceanic environment. Outdoor land environment (with simple shielding

measures) at most 500 m away from the seashore or environment on the sea.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 151

MTS9300A Telecom Power
User Manual B Technical Specifications

B Technical Specifications

B.1 Environment Specifications

Table B-1 Environment specifications
Item Specifications

Operating temperature –40ºC to +45ºC with 1120 W/m2 solar radiation

Transport temperature –40°C to +70°C

Storage temperature –40°C to +70°C

Operating humidity 5%–95% RH

Storage humidity 5%–95% RH

Altitude 0 m to 4000 m
When the altitude ranges from 2000 m to 4000
m, high temperature derating applies and the
operating temperature decreases by 1°C for each
additional 200 m.

Noise level Noise: ≤ 55 dBA@25°C, ≤ 65 dBA@45°C; complies

with the GR487 standard.

Other requirements ● There should be no conductive dust, corrosive

gas, or explosion hazard.
● Dust, corrosive substances, pests, molds, and
other indicators should be controlled in
accordance with Class 4.1 requirements in ETSI
EN 300 019-1-4 (V2.2.1).

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 152

MTS9300A Telecom Power
User Manual B Technical Specifications

B.2 Electrical Specifications

Table B-2 Electrical specifications
Item Specifications

AC input AC input system and ● 220 V single-phase: 85–300 V AC

input voltage ● 110 V dual-live wire: 90–290 V
AC
● Three-phase compatible with
single-phase: 147–519 V AC

Input frequency Frequency range: 45–66 Hz;

nominal frequency: 50 Hz/60 Hz

Power factor ≥ 0.99 (load ≥ 50%)

Total harmonic ≤ 5% (Vin = 208 V AC, 220 V AC,

distortion (THD) 230 V AC; 50%–100% load)

DC output Output voltage range ● 48 V mode: 43.2–57.6 V DC

● 57 V mode: 48–58 V DC

Default output voltage ● 48 V mode: 53.5 V DC

● 57 V mode: 57 V DC

Output power Output power = Output power of a

single rectifier x Number of
rectifiers

Regulated voltage ≤ ±1%

precision

Ripple and noise ≤ 200 mVp-p

Psophometrically ≤ 2 mV
weighted noise

Current sharing < ±5% (20%–100% load)

imbalance

AC input AC input overvoltage > 300 V AC

protection protection threshold

AC input overvoltage When the voltage is restored to 290

recovery threshold V AC, the output resumes.

AC input undervoltage < 85 V AC

protection threshold

AC input undervoltage When the voltage is restored to 90

recovery threshold V AC, the output resumes.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 153

MTS9300A Telecom Power
User Manual B Technical Specifications

Item Specifications

DC output DC output overvoltage Range: –58.5 V DC to –60.5 V DC

protection protection threshold 1. If overvoltage occurs due to an
internal fault, the rectifier locks
out.
2. If the external voltage is greater
than –63 V for more than 500
ms, the rectifier locks out.

AC surge Nominal lightning strike discharge current: 20 kA (8/20 μs);

protection maximum lightning strike discharge current: 40 kA (8/20 μs)

DC surge 10 kA in differential mode, 20 kA in common mode, 8/20 µs

protection

Safety design IEC 62368-1, IEC 62368-22

Mean time 200,000 hours (at 25°C)

between
failures (MTBF)

B.3 EMC Specifications

Table B-3 EMC specifications
Item Specifications

Electromagnetic Conducted EN 55032: 2007

interference (EMI) emission AC power port: Class B (When
NIM01C3 is configured, the system
complies with Class A)

Radiated Class B, EN 55032: 2007

emission (RE)

Harmonic EN 61000-3-12: 2008, A2: 2009

current

Voltage EN 61000-3-3: 2008

fluctuation and
flicker

Electromagnetic Electrostatic EN 61000-4-2: 2008

susceptibility (EMS) discharge (ESD) Contact discharge: 6 kV (criterion B);
air discharge: 8 kV (criterion B)
Contact discharge: 8 kV (criterion R);
air discharge: 15 kV (criterion R)

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 154

MTS9300A Telecom Power
User Manual B Technical Specifications

Item Specifications

Electrical fast EN 61000-4-4: 2004

transient (EFT) AC power port: ±2 kV (criterion B);
DC power port: ±1 kV (criterion B);
signal port: ±1 kV (criterion B)

Radiated EN 61000-4-3: 2010

susceptibility 10 V/m (criterion A)
(RS)

Conducted EN 61000-4-6: 2006

susceptibility Power port: 10 V (criterion A)
(CS)
Signal port: 3 V (criterion A)

Surge EN 61000-4-5: 2005

susceptibility ● (For the AC power port)
differential mode: ±2 kV, 8/20 µs
(criterion B); common mode: ±4
kV, 8/20 µs (criterion B)
● (For the DC power port)
differential mode: ±1 kV, 8/20 µs
(criterion B); common mode: ±2
kV, 8/20 µs (criterion B)
● (For the signal port) common
mode: 1 kV, 8/20 µs (criterion B)

Voltage dip EN 61000-4-11: 2004

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 155

MTS9300A Telecom Power
User Manual C Electrical Conceptual Diagrams

C Electrical Conceptual Diagrams

Figure C-1 Electrical conceptual diagram (three-phase)

Figure C-2 Electrical conceptual diagram (dual-live wire)

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 156

MTS9300A Telecom Power
User Manual C Electrical Conceptual Diagrams

Figure C-3 Electrical conceptual diagram (EPS100D-N01D1)

Figure C-4 Electrical conceptual diagram (EPS100D-N02A1)

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 157

MTS9300A Telecom Power D Associations Between Alarms and Dry Contacts on
User Manual the UIM

D Associations Between Alarms and Dry

Contacts on the UIM

Table D-1 Associations between dry contacts and alarms

Dry Contact Silkscreen Associated Alarm
Type

Dry contact DIN1 Dry contact input 1

inputs
DIN2 Dry contact input 2

DIN3 Dry contact input 3

DIN4 Dry contact input 4

DIN5 Dry contact input 5

DIN6 Dry contact input 6

Dry contact ALM1 AC failure

outputs
ALM2 DC overvoltage, DC ultra overvoltage, DC
The default
undervoltage, DC ultra undervoltage
setting (closed:
alarm; open: ALM3 Rectifier fault, rectifier protection,
normal) can be communication failure, multi-rectifier fault
modified.
ALM4 AC SPD faults, DC SPD faults

ALM5 Load fuse break, battery fuse break

ALM6 Battery high temperature, battery very

high temperature, battery low
temperature, battery very low temperature,
ambient high temperature, ambient very
high temperature, ambient low
temperature,

ALM7 Door Open Alarm

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 158

MTS9300A Telecom Power D Associations Between Alarms and Dry Contacts on
User Manual the UIM

Dry Contact Silkscreen Associated Alarm

Type

ALM8 Heater fault alarm, Air conditioner fault

alarm, Fan fault alarm

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 159

MTS9300A Telecom Power E How Do I Change the Communications Protocol
User Manual for COM4 and COM5?

E How Do I Change the Communications

Protocol for COM4 and COM5?

● To use CAN for communication through the COM4 port:

Take out the CIM02C, remove the jumper caps from pins 1 and 2 in the J18
position shown in Figure E-1, and insert the jumper caps into pins 2 and 3.
● To use RS232 for communication through the COM5 port:
Take out the CIM02C, remove the jumper caps from pins 1 and 2 in the J16
and J17 positions shown in Figure E-1, and insert the jumper caps into pins 2
and 3.

Figure E-1 COM4 and COM5 port jumper positions

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 160

MTS9300A Telecom Power E How Do I Change the Communications Protocol
User Manual for COM4 and COM5?

Figure E-2 Jumper connection rules for the COM4 and COM5 ports

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 161

MTS9300A Telecom Power
User Manual F Symbol Conventions

F Symbol Conventions

To ensure personal and equipment safety, observe all the safety instructions
marked on the equipment when installing, operating, and maintaining the
equipment.

Symbol Description

Indicates a part exposed to high voltage. This symbol

warns operators that both direct and indirect contact with
the power grid voltage is fatal. This symbol is attached to
a position with hazardous voltage or a power protective
cover which may be removed during maintenance.

Warns users of overheating. This symbol is attached to

equipment surface that may overheat and cause scalding.
It warns users not to touch the surface during operations
or maintenance. Users should wear heat insulation gloves
before operations to prevent scalding.

Indicates protective earthing (PE). This symbol is attached

or next to a PE terminal or a terminal that connects the
equipment to an external ground system. An equipment
ground cable is connected to an external ground bar
through the PE terminal.

Indicates equipotential bonding. This symbol is found with

equipotential terminals inside equipment.

Indicates electrostatic discharge (ESD). This symbol is used

in all electrostatic sensitive areas. Before operating
equipment in these areas, wear ESD gloves or an ESD
wrist strap.

Capacitors store hazardous energy. Open the chassis one

minute after all power supplies are disconnected.
or

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 162

MTS9300A Telecom Power
User Manual F Symbol Conventions

Symbol Description

Indicates that the equipment is safe to use at altitudes

below 2000 m.

Indicates that the equipment is not safe to use in tropical

climates.

Indicates a fan assembly or moving part. This symbol is

silkscreened on or attached to the panel of a fan assembly,
or warning operators to keep away. Do not touch rotating
blades.

This symbol is used when the usage of an equipment port

cannot be clearly described. It prompts users to refer to
or the instruction. This symbol can be used in but not limited
to the following scenarios:
1. For a multi-power supply device, use it near the power
supply to replace the multi-power supply identifier. This
symbol indicates that the device has multiple power
inputs. Therefore, when powering off the equipment,
you must disconnect all power inputs.
or
2. If there are multiple output ports, use the symbol near
the output ports. Connect cables according to the rated
power output and configuration parameter information
in the instruction.
3. If there are multiple slots, use the symbol near the slot
information area. For details, see the slot information,
restrictions on boards, and usage conditions in the
instruction.

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 163

MTS9300A Telecom Power
User Manual G Acronyms and Abbreviations

G Acronyms and Abbreviations

B
BLVD Battery low voltage disconnection

E
EMC Electromagnetic compatibility
EMI Electromagnetic interference
EMS Electromagnetic susceptibility

H
HTTPS Hypertext Transfer Protocol Secure

L
LLVD Load low voltage disconnection

I
IEC International Electrotechnical
Commission

M
MTBF Mean time between failures

S
SMU Site monitoring unit
SNMP Simple Network Management Protocol
SPD Surge protection device

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 164

MTS9300A Telecom Power
User Manual G Acronyms and Abbreviations

UIM User interface module

Issue 11 (2023-03-15) Copyright © Huawei Technologies Co., Ltd. 165