Guided-Wave-Radar-Level-Transmitter (1)
Guided-Wave-Radar-Level-Transmitter (1)
3300
Effective : Sept.. 2011
... the level & gas people
ISO-9001 : 2008 CERTIFIED COMPANY
Product Description
Working principle
Guided wave radar transmitter works on the principle of time and travel (TDR). Radar wave
travels at the velocity of light. The flying time is converted into level signal via the electronic
components. The probe emits high frequency wave pulse which travels along a cable probe
or a rod probe. When the wave pulse reaches the medium surface, it will be reflected and
received by the receiver, and then the distance signal will be converted into level signals.
Input
The reflected wave pulse travels back along the
cable and arrives at the electronic unit. The
microprocessor will process the signals and
recognize the returned waves from medium
surface. The identification of correct return wave
signals can be done by the intelligent software. The
distance D from the medium surface is proportional to the
travel time: D=C X T/2 (C is velocity of light)
Due to the empty tank distance D is known, and then the level L is: L=E-D
Output
By setting of empty tank height E as zero point, the height of full tank F as full range point, and
other applicable parameter, the instrument will adapt into the working environment
automatically and correspond to output 4-20mA.
Page No.2
Dead zone at bottom refers to the distance which cannot be measured accurately nearby the
bottom of the cable.
The distance between the dead zone at the top and the dead zone at the bottom is the effective
measuring distance.
Note:
Level measurement in a tank can be effectively performed only when the medium level within the
top dead zone and the bottom dead zone.
Introduction of Transmitter
Type : Rope
Application: liquid and solid powder.
Measuring range: 30m
Enclosure : Die Cast Aluminum
Process connection: thread, flange
Process temperature: -40°C~+250°C
Process pressure: -1~20Kg cm²
Accuracy: ±3mm
Repeatability: ±2mm
Frequency range: 100MHZ~1.8GHz
Signal output: 4-20mA/ HART (2-wire)
501E-32-A
Enclosure Protection : IP66
Measuring range: 6m
Accuracy: ±3mm
Repeatability: ±2mm
Frequency range: 100MHZ~1.8GHz
Type: Rod
Application: liquid
Measuring range: 6m
Enclosure : Die Cast Aluminum
Process connection: thread, flange
Process temperature: -40°C~+400°C
Process pressure: -1~40Kg cm²
Accuracy: ±3mm
Repeatability: ±2mm
Frequency range: 100MHZ~1.8GHz
501E-32-D
Signal output: 4-20mA/ HART (2-wire)
Enclosure Protection : IP66
Type: Rope/Rod
Application: corrosive liquids
Measuring range: 6m (for rod probe)/ 20m (for cable probe)
Enclosure : Die Cast Aluminum
Process connection: flange
Process temperature: -40°C~+120°C
Process pressure: -1~20Kg cm²
Accuracy: ±3mm
Repeatability: ±2mm
Frequency range: 100MHZ~1.8GHz
Signal output: 4-20mA/ HART (2-wire) 501E-32-E
Enclosure Protection : IP66
Page No.4
Type: Co-axial Rod
Application: liquids with lower dielectric constant or liquids with wave surface
Measuring range: 6m
Enclosure : Die Cast Aluminum
Process connection: thread, flange
Process temperature: -40°C~+250°C
Process pressure: -1~20Kg cm²
Accuracy: ±3mm
Repeatability: ±2mm
Frequency range: 100MHZ~1.8GHz
Signal output: 4-20mA/ HART (2-wire)
501E-32-F
Enclosure Protection Grade : IP66
General Specifications
— Working frequency : 100MHz~1.8GHz
—Application : Liquid, Solid Powder, Corrosive Liquid, Liquid with low die electric
— Output Signal : 4~20mA Output Superimposed with HART® Protocol/ Field bus
— System : 2 Wire
Model Selection Reference Table For Guided Wave Radar Level Transmitter
Antenna Dielectic Solid Solid
Model Application Liquid Accuracy Beam angle
diameter constant particles powder
501E-32-C Solid/Liquid Both 6mm 2.5~3.0 N.A 20mm 25m 3mm N.A
Please Specify
Model Selection
501E-32-A / B / C / D / E / F..........
Electrical Classification
Weather proof............................................ W
Explosion proof.......................................... E
Intrinsically Safe......................................... I
Measuring Range
6 Mtr. ......................................................
Please Specify
10 Mtr......................................................
20 Mtr......................................................
30 Mtr......................................................
Output
4-20mA linear Output........................................ H
Fieldbus Output................................................. F
Process Connection
501E-32-A 501E-32-C
& & 501E-32-E 501E-32-F
501E-32-B 501E-32-D
A1 - 1½”NPT B1 - 3” Flange C1 -1½”NPT D1 - 2” Flange
A2 - 2” Flange B2 - 4” Flange C2 -2” Flange D2 - 3” Flange
Please Specify
Page No.24