Intertac Plus
Compiler: Shujing Shao Issuing Date:2023/09/18 Technical Data Sheet
Characteristic
Intertac Plus is a Solvent Free, Low Odour, Low VOC Pressure Sensitive adhesive formulated for
installing Interface Glasbac& Cushion Back Carpet Tiles as well as Interface range of Luxury Vinyl
Tiles and Plank . Intertac Plus can be applied to concrete substrates with a moisture content up to
99% Relative Humidity (moisture reducing) tested with the In- Situ Probe method and concrete
substrates with pH readings up to 12.0.
Specification
1. Appearance：Green liquid
2. Solid content：49 %~52%
3. pH: 7.0~9.0
4. Viscosity:25000~35000 mPa.s(25℃，RVT:6#/10rpm)
Features
♦Installer Friendly.
♦ Building Green Credits
♦ Green Star Compliant
♦ 99% RH Resistant Formulation
♦ Solvent Free
♦ Anti-microbial Formulation
♦ Low Odour
♦ Low VOC Emission
南寶樹脂(中國)有限公司
NAN PAO RESINS (CHINA) CO., LTD
江苏省昆山市昆嘉路 600 号
TEL:0512-57708888
Intertac Plus
Compiler: Shujing Shao Issuing Date:2023/09/18 Technical Data Sheet
For Bonding
Interface Glasbac & Cushion Back Carpet Tiles as well as Interface range of Luxury Vinyl Tiles and
Plank。
Surface Preparation
To be in accordance with the current Australian Standard “Floor Coverings - 1884-2012. Resilient
Sheet & Tiles - Laying & Maintenance Practices” or Australian Standard 2455.2.2019“Textile Floor
Coverings - Installation Practice”.
All surfaces to be bonded shall be absorbent, dry, smooth, sound and clean. Subfloors must also be
free of wax, grease, paint, previously used adhesive, polish, PVC based membranes and hydrostatic
pressure.
All concrete floors should be tested for moisture content in accordance the above Australian
Standards prior to the undertaking surface preparation or installation of floorcoverings.
The minimum sublfoor temperature before commencing surface preparation and adhesive application
is 10°C.
It is recommended that highly absorbent concrete subfloors be primed with Roberts R400 floor and
wall primer prior to the application of adhesive .
Indentations and uneven concrete subfloors should be treated with the Roberts range of levelling
compound and be in accordance with manufacturer’s recommendations.
Application& Spread Rate
Spread adhesive with the recommended notched trowel.
For the application of Interface Luxury Vinyl Tiles and Planks it is recommended to apply the adhesive
with a 1.6mm x1.6mm ‘V1” notched trowel.
For securing Interface Glasbac Carpet tiles the use a log nap roller with a pile height of no less than
10mm is recommended. Alternatively applying adhesive with a 1.6mm x1.6mm notched “V1” notched
trowel is also recommended.
南寶樹脂(中國)有限公司
NAN PAO RESINS (CHINA) CO., LTD
江苏省昆山市昆嘉路 600 号
TEL:0512-57708888
Intertac Plus
Compiler: Shujing Shao Issuing Date:2023/09/18 Technical Data Sheet
Intertac Plus adhesive is used in dry mode, allow the adhesive to dry and become clear, this will limit
the transfer of the adhesive to the back of the carpet tiles therefore enabling them to be relayed or
repositioned with a clean backing.
Please ensure it is rolled in both directions to ensure transfer has occurred.
Coverage when applying adhesive with a 1.6mm x 1.6mm (V1) notched trowel will achieve up to 5
square metres per litre.
Coverage when applying adhesive with a Long Nap Roller Pile height no less than 10mm can achieve
an approximate spread rate of 10-14 square metres per litre.
Coverage when applying adhesive with a 2.4mm x 2.4mm (V2) notched trowel will achieve up to 3
square.
Setting Times
Intertacplus Adhesive will tack up and turn clear after approximately 30 minutes to 1 hour at 20°C.
Times may vary depending on substrate absorbency, temperature and humidity.
Clean Up
Clean tools immediately after use with warm soapy water. Dried adhesive may be cleaned off using
R550 Latex/Acrylic Adhesive Remover applied to a damp cloth then rubbed gently over the dried
adhesive or alternatively please use AFTEK Handy Wipes.
Shife Life
18 months in unopened containers stored out of direct sunlight.
Container Sizes
15 litre plastic containers.
南寶樹脂(中國)有限公司
NAN PAO RESINS (CHINA) CO., LTD
江苏省昆山市昆嘉路 600 号
TEL:0512-57708888
