RLC-circuits TEP

Keywords
Damped and forced oscillations, Kirchhoff’s laws, series and parallel tuned circuit, resistance,
capacitance, inductance, reactance, impedance, phase displacement, Q-factor, band-width

Application
RLC-circuits are used as frequency filters or resonators in electronic devices; e.g in radio transmitters
and receivers the frequency tuning is accomplished by setting the RLC-circuit to resonate on a special
frequency.

Radio receiver

Experimental set-up

RLC element (series)

Learning objective
The resonance-behaviour of a RLC-circuit is studied and the resonance frequencies f res are
determined and compared with the theoretical values
1
f res= .
2 π √L C
The resonance curves are measured and the impedance-behaviour of the LC-component is analysed.
Further the bandwidths B and the quality factors Q are determined from the resonance curves and
compared with the theoretical values for a series-tuned circuit, obtained from the parameters of the
electrical components.

www.phywe.com
P2440601 PHYWE Systeme GmbH & Co. KG © All rights reserved 1
 TEP RLC-circuits

Tasks

1. Measure the voltage drop U over the LC-component and the current I through the circuit
and determine the resonance frequency for both combinations of coil and capacitor; compare
with the theoretical values

a) for the series-tuned circuit with resistors R=47 Ω and R=100 Ω .

b) for the parallel-tuned circuit with resistor R=470 Ω .

2. Determine the impedance Z of the LC-component for both circuits with the measurements from
task 1 and compare with the theoretical values.

3. Determine the bandwidth B and Q-factor for the series-tuned circuit from the resonance curve
and compare with the theoretical values (determined by the parameters of the electrical
components).

Equipment
1 Digital Function Generator, USB 13654-99
1 Coil, 900 turns 06512-01
1 Capacitor 100 nF/250 V, G1 39105-18
1 Capacitor 470 nF/250 V, G1 39105-20
1 Resistor 47 Ohm, 1W, G1 39104-62
1 Resistor 100 Ohm, 1W, G1 39104-63
1 Resistor 470 Ohm, 1W, G1 39104-15
1 Multi-range meter/overl.prot.B (Multimeter) 07026-00
1 Connection box 06030-23
4 Connecting cord, 32 A, 500 mm, black 07361-05
2 Connecting cord, 32 A, 250 mm, black 07360-05
1 Short-circuit plug,black 06027-05

Theory
A RLC-circuit (also oscillating, oscillator or resonant circuit) consists of a resistor (R), an inductance (L)
and a capacitor (C) – sometimes it is also refered to as LC-circuit, because the resistor is used to
simulate the loss-resistance of a real circuit. Generally one differs between two kinds of RLC-circuits, the
series- and the parallel-tuned circuit. The circuit diagramms are shown in Fig. 1 and 2, respectively.

Fig. 1: Fig. 2:
circuit diagramm for a series-tuned RLC-circuit circuit diagramm for a parallel-tuned RLC-circuit

2 PHYWE Systeme GmbH & Co. KG © All rights reserved P2440601

 RLC-circuits TEP

When a fully charged capacitor is discharged through an inductance coil, the discharge current induces a
magnetic field in the coil, which reaches its maximum, when the capacitor is completely discharged.
Then, due to the decreasing current, the change in the magnetic field induces a voltage which according
to Lenz's law charges the capacitor. Now the current decreases to zero until the capacitor is completely
charged again, but with reversed sign of charges. At this point, the procedure starts again, but with
opposite direction of the current. In absence of any resistance, this charging and discharging would
oscillate forever – but because of ohmic resistances which every real circuit posesses, the oscillation is
damped and so the amplitude of current and voltage decreases by time.

According to Kirchoff's law the total voltage in one loop must add to zero or be equal to an external
potential. Therefore we obtain for the circuit in Fig. 1:
U L +U C +U R=U ext , (1)
where

d
• U L=L I is the voltage drop across the inductance L,
dt
Q
• U C= is the voltage drop across the capacitor C,
C (2)
• U R =R I is the voltage drop across the resistor R,
• U ext =U FG=U 0⋅exp {i ω t} is the external voltage, which in our case is the
output of the function generator
d
Using these identities and differentiating (1) with respect to time t , one obtains with Q=I :
dt
d2 d 1
L 2 I + R I + I =i ω U 0 exp {i ω t} (3)
dt dt C
This equation can be easily transformed into the inhomogeneous differential equation for the forced
1 R
oscillation; by using Euler's formula, ω0= and the damping coefficient δ= one obtains
√ LC 2L
Ï +2 δ İ + ω20 I = ω U 0 exp {i(ω t+ π )} . (4)
L 2
The real part of the solution for (3) gives the current
I =I 0 ∙ cos(ωt−φ) (5)
with
U0
I0 = .

√
2
(6)
(
R2 + ω L−
1
ωC )
The phase displacement ϕ is given by

tan ϕ=−
1
R (
ω L−
1
ωC ) (7)

and the resonance point is found at

1
ω=ω0= . (8)
√ LC

www.phywe.com
P2440601 PHYWE Systeme GmbH & Co. KG © All rights reserved 3
 TEP RLC-circuits

U eff
The impedance (value) is defined by Z = . From (6) one obtains for the LC-component of the
I eff
series-tuned circuit
1
Z s= ω L−| ωC | (9)

(the absolut value is due to the fact that Z is actually a complex value).
In contrast to the mechanical oscillation, here the resonance frequency is independent of the
dampening. As can be easily shown from relations (6) and (7), at the resonance point the phase
displacement becomes zero in all components of the circuits.

In the case of the parallel-tuned RLC-circuit, we apply Kirchhoff's first law:

I R + I L + I C =0 (10)
Because the function generator represents a constant voltage source (and not constant current), we
differentiate equ. (10) with respect to time, use the identities (2) and we obtain
1 1
Ü + U̇ + U =0 . (11)
RC LC
With the ansatz U (t)=U 0⋅exp {i ω t} and after discarding the imaginary part one directly obtains the
1
resonance frequency ω0= . To determine the impedance for the parallel tuned circuit, one simply
√ LC
U (t )
uses (10) with I R=I and I ( t)= to obtain
Z
U (t) U (t) U (t ) 1 1
Zp
=
XL
+
XC
⇒
Zp
=
iω L
+i ω C . | | (12)

Applying Kirchhoff's first law on the complete circuit and regarding the LC-component as one element
one gets
U ext =U R +U LC
(13)
U 0⋅exp {iω t}=R I +Z LC I
(here Z LC=Z p ). Therefore the solution for the current is, after neglecting the imaginary part,
I ( t)=I 0 cos (ω t + ϕ) (14)
with
U0
I0 = .

√
2
R+
ωL
2
1−ω ω( 0
) (15)

The phase displacement ϕ is given by

1
tan ϕ= .
R
1
ωL(−ωC ) (16)

Comparing the calculations from above, the results are the following:
Both circuits (series- and parallel-tuned) have the same resonance frequency

4 PHYWE Systeme GmbH & Co. KG © All rights reserved P2440601

 RLC-circuits TEP

ω0 1
f res= = . (17)
2 π 2 π √ LC
In the series-tuned case, the impedance tends to zero when the frequency is approaching the resonance
frequency, which can be seen in the increase of current. In the parallel-tuned case, the impedance of the
LC-component increases while approaching the resonance frequency, which can be seen in the
decrease of current.

Another physical quantity, which describes the behaviour of a resonating system is the bandwith B and
the quality-factor Q . The bandwidth of a resonance curve is simply defined as the distance between
A res
the two points where the maximum amplitude A max = Ares at the resonance drops to a value (see
√2
Fig. 3), so
B=f 2−f 1 . (18)
The quality factor Q is given by
f res
Q= . (19)
B
In the series-tuned circuit, the quality factor can also be expressed as

Q=
1 L
R C√,

which can be derived from the equations above (but usually one uses
(20)

the relation B=2 δ , where δ is the damping, which provides a

much easier and faster way to obtain equ. (20)). One can see, that the
resistor is responsible for the shape of the resonance curve, too. Fig. 3

In the parallel-tuned circuit, the quality factor, expressed through the parameters of the electrical
components, is given by

Q=R
√ C
L
. (21)

Set-Up
The experimental set-up for measuring the voltage and current in the series-tuned circuit is shown in Fig.
4a and 4b, respectively. Ri denotes the internal resistance of the digital function generator, which is
given in the technical description as Ri=2 Ω .
The experimental set-up for measuring the voltage and current in the parallel-tuned circuit is shown in
Fig. 5a and 5b, respectively.

For the digital function generator select following settings:

DC-offset: ±0V
Amplitude (USS): 10 V
Frequency: 0 - 10 kHz
Mode: sinusoidal

www.phywe.com
P2440601 PHYWE Systeme GmbH & Co. KG © All rights reserved 5
 TEP RLC-circuits

Fig. 4a Fig. 4b

Fig. 5a Fig. 5b

Select the following measuring ranges on the Multimeter:

series-tuned circuit:
Voltage (~): 3 V
Current (~): 30 mA
parallel-tuned circuit:
Voltage (~): 1 V
Current (~): 10 mA

The settings can be altered according to the experimenter's discretion. But is it important to leave the
settings constant during the experiment. Especially the measuring ranges of the multimeter must remain
the same during the measurement, because different ranges use different internal resistors! It is
recommended to adjust the measuring range of the multimeter at the maximum of the resonance point
(current for series tuned circuit and voltage for parallel tuned circuit) and leave them unchanged during
the measurement.

6 PHYWE Systeme GmbH & Co. KG © All rights reserved P2440601

 RLC-circuits TEP

Procedure
The voltage U and current I are measured according to the set-up for different frequencies f ,
which can be set and directly read off at the digital function generator. The frequency steps should get
smaller when approaching the resonance frequency.
Nevertheless it is recommended to determine the resonance frequencies for the different values of
electrical components first, in order to have an idea how to choose the steps. For this one should use the
quantity, which reaches its minimum at the resonance frequency.
It is recommended to note all measurements for one quantity (e.g. the voltage) for the different
frequencies first and then measure the other quantity (e.g. current) for the same frequencies.

Results
The resonance frequencies f res are measured as follows:
0.1 µF 0.47 µF
series 3401 Hz 1552 Hz
parallel 3400 Hz 1554 Hz

Now the voltage drops U over the LC-components and the currents I through the circuits are
measured at different frequencies for the different set-ups:
For the series-tuned circuit we obtain the following results:
C = 0.1 µF C = 0.47 µF
R = 47Ω R = 100Ω R = 47Ω R = 100Ω
f [kHz] I [mA] U [V] f [kHz] I [mA] U [V] f [kHz] I [mA] U [V] f [kHz] I [mA] U [V]
0.5 0.5 1.60 0.5 0.5 1.60 0.1 0.5 1.60 0.1 0.5 1.60
1.0 1.0 1.60 1.0 1.0 1.60 0.2 1.0 1.60 0.2 1.0 1.60
1.5 2.0 1.60 1.5 2.0 1.60 0.3 1.5 1.60 0.3 1.5 1.60
2.0 3.0 1.60 2.0 3.0 1.55 0.4 2.0 1.60 0.4 2.0 1.60
2.2 4.0 1.60 2.2 4.0 1.55 0.5 2.5 1.60 0.5 2.5 1.60
2.4 5.0 1.60 2.4 4.5 1.55 0.6 3.0 1.60 0.6 3.0 1.60
2.6 6.0 1.60 2.6 6.0 1.50 0.7 4.0 1.60 0.7 4.0 1.55
2.8 8.5 1.55 2.8 7.5 1.40 0.8 5.0 1.60 0.8 5.0 1.50
3.0 12.5 1.45 3.0 10.0 1.20 0.9 6.5 1.60 0.9 6.0 1.50
3.1 15.5 1.35 3.1 11.5 1.00 1.0 8.0 1.60 1.0 7.5 1.40
3.2 20.0 1.15 3.2 13.0 0.75 1.1 10.0 1.55 1.1 9.0 1.30
3.3 25.0 0.75 3.3 14.0 0.45 1.2 13.0 1.45 1.2 10.5 1.20
3.4 27.5 0.35 3.4 14.5 0.20 1.3 17.5 1.30 1.3 12.5 0.95
3.5 25.0 0.70 3.5 14.0 0.40 1.4 23.0 1.15 1.4 14.0 0.60
3.6 20.5 1.10 3.6 13.0 0.70 1.5 29.0 0.50 1.5 15.0 0.25
3.7 16.5 1.30 3.7 12.0 0.95 1.6 30.0 0.25 1.6 15.5 0.10
3.8 14.0 1.40 3.8 11.0 1.10 1.6 29.0 0.40 1.6 15.0 0.20
4.0 10.0 1.50 4.0 8.5 1.30 1.7 24.5 0.95 1.7 14.5 0.55
4.2 8.0 1.55 4.2 7.0 1.40 1.8 20.0 1.25 1.8 13.0 0.80
4.4 6.5 1.55 4.4 6.0 1.45 1.9 16.0 1.40 1.9 12.0 1.00
4.6 5.5 1.60 4.6 5.5 1.50 2.0 13.5 1.45 2.0 11.0 1.15
5.0 4.5 1.60 5.0 4.0 1.55 2.1 12.0 1.50 2.1 10.0 1.25
5.5 3.5 1.60 5.5 3.5 1.55 2.2 10.5 1.50 2.2 9.0 1.30
6.0 3.0 1.60 6.0 3.0 1.55 2.3 9.0 1.55 2.3 8.0 1.35
6.5 2.5 1.60 6.5 2.5 1.55 2.4 8.5 1.55 2.4 7.5 1.40
7.0 2.0 1.60 7.0 2.0 1.55 2.5 7.5 1.60 2.5 7.0 1.40
7.5 2.0 1.60 7.5 2.0 1.55 2.6 7.0 1.60 2.6 6.5 1.45
8.0 2.0 1.60 8.0 2.0 1.55 2.7 6.5 1.60 2.7 6.0 1.45
2.8 6.0 1.60 2.8 5.5 1.50
2.9 6.0 1.60 2.9 5.5 1.50
3.0 5.5 1.60 3.0 5.0 1.50

www.phywe.com
P2440601 PHYWE Systeme GmbH & Co. KG © All rights reserved 7
 TEP RLC-circuits

For the parallel-tuned circuit we obtain the following results:

C = 0.1 µF C = 0.47 µF
f [kHz] U [V] I [mA] f [kHz] U [V] I [mA] f [kHz] U [V] I [mA] f [kHz] U [V] I [mA]
0.50 0.20 2.90 3.50 1.36 0.20 0.10 0.05 2.92 1.60 1.30 0.50
1.00 0.40 2.80 3.60 1.36 0.40 0.20 0.08 2.92 1.70 1.25 1.20
1.50 0.65 2.60 3.70 1.36 0.55 0.30 0.11 2.91 1.80 1.15 1.73
2.00 0.95 2.30 3.80 1.35 0.75 0.40 0.16 2.90 1.90 1.05 2.10
2.20 1.05 2.10 4.00 1.32 1.05 0.50 0.22 2.90 2.00 0.95 2.30
2.40 1.15 1.85 4.20 1.30 1.30 0.60 0.28 2.90 2.10 0.85 2.45
2.60 1.20 1.55 4.40 1.25 1.50 0.70 0.35 2.85 2.20 0.75 2.55
2.80 1.30 1.20 4.60 1.20 1.70 0.80 0.42 2.80 2.30 0.70 2.65
3.00 1.32 0.80 5.00 1.10 2.00 0.90 0.51 2.75 2.40 0.65 2.70
3.10 1.34 0.60 5.50 1.00 2.25 1.00 0.62 2.65 2.50 0.60 2.72
3.20 1.35 0.40 6.00 0.90 2.40 1.10 0.75 2.50 2.60 0.55 2.75
3.30 1.36 0.25 6.50 0.80 2.55 1.20 0.90 2.28 2.70 0.53 2.80
3.35 1.36 0.15 7.00 0.75 2.60 1.30 1.05 1.90 2.80 0.50 2.80
3.40 1.36 0.10 7.50 0.70 2.65 1.40 1.20 1.30 2.90 0.48 2.81
3.45 1.36 0.12 8.00 0.65 2.70 1.50 1.30 0.53 3.00 0.45 2.82
1.55 1.30 0.27

Evaluation
Task 1: Determine the resonance frequency for both combinations of coil and capacitor and compare
with the theoretical values:
Because the resonance frequency is the same for both series- and parallel-tuned circuits and is
additionally independent of the resistors, one has to consider only two cases for the two capacitors.
From equ. (8) one gets
1
f res= ,
2 π √L C
which in this case leads to the theoretical values ( L=24 mH ):
C 0.1 µF 0.47 µF
fres 3249 Hz 1499 Hz
Comparing the measured and the theoretical values, one finds that the results are within 5% deviation.
The plotted resonance curves are shown in Fig. 6 – Fig. 7:

Fig. 6a:
Resonance curve
of the current in the
series tuned circuit
with C=0.1μ F (t
he values I res / √ 2
for the bandwidth
are plotted as
I=const. graphs)

8 PHYWE Systeme GmbH & Co. KG © All rights reserved P2440601

 RLC-circuits TEP

Fig. 6b: Resonance curve of the current in the series tuned circuit with C=0.47μ F (the values
I res / √ 2 for the bandwidth are plotted as I=const. graphs)

Fig. 7a: Resonance curve of the voltage in the Fig. 7b: Resonance curve of the voltage in the
parallel tuned circuit with C=0.1μ F (the values parallel tuned circuit with C=0.47μ F (the values
U res / √ 2 for the bandwidth are plotted as U res / √ 2 for the bandwidth are plotted as
y=const. Graphs) y=const. Graphs)

www.phywe.com
P2440601 PHYWE Systeme GmbH & Co. KG © All rights reserved 9
 TEP RLC-circuits

Task 2: Determine the impedance Z of the LC-component for both circuits with the measurements
from task 1 and compare with the theoretical values.
The measured values Z m of the impedance are simply derived by
U (f )
Zm= ,
I (f )
where U (f ) and I (f ) are the voltage and current measured in task 1 at the frequency f . The
theoretical value for the series tuned circuit is given by equ. (9), and one obtains for C=0.1μ F :
C = 0.1 µF
Z_m [Ω] Z_m [Ω] Z_m [Ω] Z_m [Ω]
f [kHz] (R=47Ω) (R=100Ω) Z_th [Ω] f [kHz] (R=47Ω) (R=100Ω) Z_th [Ω]
0.5 3200 3200 3108 3.6 54 54 101 Note:
1.0 1600 1600 1441 3.7 79 79 128
1.5 800 800 835 3.8 100 100 154
One has to take care of the
2.0 533 517 494 4.0 150 153 205 correct values of powers of
2.2 400 388 392 4.2 194 200 254 ten!
2.4 320 344 301 4.4 238 242 302
2.6 267 250 220 4.6 291 273 348
2.8 182 187 146 5.0 356 388 436
3.0 116 120 78 5.5 457 443 540
3.1 87 87 46 6.0 533 517 640
3.2 58 58 15 6.5 640 620 735
3.3 30 32 15 7.0 800 775 828
3.4 13 14 45 7.5 800 775 919
3.5 28 29 73 8.0 800 775 1007

The plotted curves for the impendances for the series-tuned circuit with C=0.1μ F are plotted in
Fig. 8:

Fig. 8: theoretical and measured impedances in the series tuned circuits with C=0.1μ F

10 PHYWE Systeme GmbH & Co. KG © All rights reserved P2440601

 RLC-circuits TEP

For C=0.47μ F one gets:

C = 0.47 µF
Z_m [Ω] Z_m [Ω] Z_m [Ω] Z_m [Ω]
f [kHz] (R=47Ω) (R=100Ω) Z_th [Ω] f [kHz] (R=47Ω) (R=100Ω) Z_th [Ω]
0.1 3200 3200 3371 1.6 14 13 30
0.2 1600 1600 1663 1.7 39 38 57
0.3 1067 1067 1084 1.8 63 62 83
0.4 800 800 786 1.9 88 83 108
0.5 640 640 602 2.0 107 105 132
0.6 533 533 474 2.1 125 125 155
0.7 400 388 378 2.2 143 144 178
0.8 320 300 303 2.3 172 169 200
0.9 246 250 241 2.4 182 187 221
1.0 200 187 188 2.5 213 200 242
1.1 155 144 142 2.6 229 223 262
1.2 112 114 101 2.7 246 242 282
1.3 74 76 64 2.8 267 273 301
1.4 50 43 31 2.9 267 273 321
1.5 17 17 0 3.0 291 300 340
1.6 8 6 15

The plotted curves for the impendances for the series-tuned circuit with C=0.47μ F are plotted in Fig.
9a and Fig. 9b (different scaling on the y-axis):

Fig. 9a and 9b:

theoretical and measured
impedances in the series
tuned circuits with
C=0.47μ F

www.phywe.com
P2440601 PHYWE Systeme GmbH & Co. KG © All rights reserved 11
 TEP RLC-circuits

In the parallel-tuned circuit we obtain the theoretical values for the impedance of the LC-component by
using equ. (12):
C = 0.1 µF C = 0.47 µF
f [kHz] Z_m [Ω] Z_th [Ω] f [kHz] Z_m [Ω] Z_th [Ω] f [kHz] Z_m [Ω] Z_th [Ω] f [kHz] Z_m [Ω] Z_th [Ω]
0.50 69 77 3.50 6800 3285 0.10 17 15 1.60 2600 1723
1.00 143 167 3.60 3400 2382 0.20 27 31 1.70 1042 893
1.50 250 287 3.70 2473 1878 0.30 38 47 1.80 665 613
2.00 413 486 3.80 1800 1556 0.40 55 65 1.90 500 472
2.20 500 613 4.00 1257 1169 0.50 76 85 2.00 413 386
2.40 622 797 4.20 1000 943 0.60 97 108 2.10 347 329
2.60 774 1091 4.40 833 795 0.70 123 135 2.20 294 287
2.80 1083 1642 4.60 706 690 0.80 150 169 2.30 264 256
3.00 1650 3072 5.00 550 551 0.90 185 212 2.40 241 231
3.10 2233 5225 5.50 444 444 1.00 234 272 2.50 221 211
3.20 3375 16205 6.00 375 375 1.10 300 360 2.60 200 195
3.30 5440 15645 6.50 314 326 1.20 395 504 2.70 189 181
3.35 9067 7979 7.00 288 290 1.30 553 792 2.80 179 169
3.40 13600 5381 7.50 264 261 1.40 923 1660 2.90 171 159
3.45 11333 4073 8.00 241 238 1.50 2453 115274 3.00 160 150
1.55 4815 3345

The plotted curves for the impendances for the parallel-tuned circuit are plotted in Fig. 10a and 10b:

Fig. 10a: theoretical and measured impedances in the parallel-tuned circuits with C=0.1μ F .

12 PHYWE Systeme GmbH & Co. KG © All rights reserved P2440601

 RLC-circuits TEP

Fig. 10b: theoretical and measured impedances in the parallel-tuned circuits with C=0.47μ F
One can see, that the values of the measured impedances partially differ widely from the theoretical
values, nevertheless the general behaviour is confirmed. The biggest deviations are present near the
resonance frequency, where the ohmic part of the impedance (the ohmic resistance of the coil)
contributes more than at the edges of the plotted curves.

Task 3: Determine the bandwidth B and Q-factor for the series-tuned circuit from the resonance curve
and compare with the theoretical values
The theoretical values for the quality factor Q are given by equ. (20), but before inserting the values,
one must consider the different parts which contribute to the total resistance. These are the ohmic
resistor R itself, the real part of the impedanze at the resonance point, here simply denoted as R LC ,
which is simply given by
U res
RLC =,
I res
and the internal resistance of the function generator Ri . Therefore
U res
Qth =
1 L
R tot C√ with Rtot =R+ Ri + R LC=R+ R i+
I res
.

The measured value of the quality factor Q m is calculated with equ. (19). The frequencies f 1 and
f 2 for the bandwith are determined from the plot in Fig. 6 & 7.
For the series-tuned case with C=0.1μ F one gets

Rtot f1 f2 B Qm Qth
R = 47 Ω 61.7 Ω 3.19 kHz 3.63 kHz 0.44 kHz 7.7 7.9
R = 100 Ω 114.4 Ω 3.02 kHz 3.86 kHz 0.84 kHz 4.0 4.3

The theoretical and measured values coincide quite well (deviation within 5% in the circuit with
R=47 Ω and within 7% in the circuit with R=100 Ω ).

www.phywe.com
P2440601 PHYWE Systeme GmbH & Co. KG © All rights reserved 13
 TEP RLC-circuits

For the series-tuned case with C=0.47μ F one gets

Rtot f1 f2 B Qm Qth
R = 47 Ω 56.7 Ω 1.37 kHz 1.77 0.4 kHz 3.88 3.99
R = 100 Ω 109.1 Ω 1.23 kHz 2.00 0.78 kHz 2.00 2.07

In this case the values coincide even better (within 4%).

For completeness, we would like to compare the values of the quality factor for the parallel-tuned circuit
(but here we consider only the resistor R=470Ω , because the influence of multimeter etc. is much
more complicated than in the series-tuned circuit):

f1 f2 B Qm Qth
R = 470 Ω 1.37 kHz 1.77 kHz 0.4 kHz 3.88 3.99

In the parallel-tuned case the theoretical and measured value of the quality factor Q coincide within
3%.

14 PHYWE Systeme GmbH & Co. KG © All rights reserved P2440601