(+34) 968 162 005

www.sensovant.com
[email protected]

AIR FLOW AND VELOCITY TRANSMITTERS

DPT-FLOW-MOD

AIR FLOW
Multifunctional air flow transmitters for building automation systems
with Modbus communication

The DPT-Flow-MOD series air flow transmitters are engineered for

building automation in the HVAC/R industry. The most technologically
advanced transmitters on the market, measuring volume flow, velocity,
and static and differential pressure. The measurements can be read
and the configuration can be done via Modbus communication. The
DPT-Flow-MOD series devices can be connected directly to the pres -
sure measurement points in a centrifugal fan, providing accurate flow
measurement of the fan. The smart user interface enables easy selec -
tion of settings according to the selected fan or in-duct measurement
probe.

DPT-Flow-MOD series devices include:

• Two selectable functions:
o Measure and monitor in-duct volume flow, velocity or
differential pressure
o Measure and monitor air flow across centrifugal fans
• Multiple selectable measurement units:
o Volume flow: m3/s, m3/h, cfm, l/s
o Velocity: m/s, ft/min
o Pressure: Pa, inWC, mmWC, kPa, mbar
• Modbus communication protocol

DPT-Flow-MOD series device options offer:

• AZ (autozero) function for automatic zero point calibration,
eliminating the need for periodic manual autozeroing
to ensure long term accuracy

SIMILAR PRODUCTS APPLICATIONS

• AVT series air velocity transmitters DPT-Flow-MOD series devices are commonly used in HVAC/R
• DPT-2W-Q series differential pressure transmitters with systems for:
flow linear output • air flow monitoring across centrifugal fans and blowers
• DPT-R8 series 8-range differential pressure transmitters • in-duct air flow or pressure monitoring
• DPT-MOD series differential pressure transmitters with • measuring air flow or pressure in VAV applications
Modbus configuration

MODEL SUMMARY

DPT-FLOW-MOD-2500 DPT-FLOW-MOD-7000

Measurement ranges (Pa) 0−2500 Pa 0−7000 Pa

Description Model Product code Model Product code

Flow meter for measuring air flow in duct and on centrifugal fans
with Modbus communication

- with display DPT-FLOW-MOD-2500-D 102.011.001 DPT-FLOW-MOD-7000-D 102.006.027

- with autozero and display DPT-FLOW-MOD-2500-AZ-D 102.011.003 DPT-FLOW-MOD-7000-AZ-D 102.006.029

SENSOVANT www.sensovant.com Datasheet Version 3.0 2016

AIR FLOW AND VELOCITY TRANSMITTERS
DPT-FLOW-MOD
Multifunctional air flow transmitters for building automation systems with Modbus communication
SPECIFICATIONS
Performance Technical Specifications Display
Accuracy (at applied pressure): Media compatibility: 2-line display (12 characters/line)
Ranges < 125 Pa = ±2 Pa Dry air or non-aggressive gases Line 1: Volume or velocity measurement
Ranges 125 Pa = ±1,5 % Pa Pressure units (select via menu): Line 2: Pressure measurement
(Accuracy specifications include: general accuracy, Pa, kPa, mbar, inWC, mmWC Size: 46.0 x 14.5 mm
temperature drift, linearity, hysteresis, long term Flow units (select via menu): Electrical connections:
stability, and repetition error) Volume: m3/s, m3/hr, cfm, l/s 4-screw terminal block
Thermal effects: Velocity: m/s, ft/min Wire: 12–24 AWG (0.2–1.5 mm 2)
Temperature compensated across the full spectrum of Measuring element: Cable entry:
capability MEMS Strain relief: M16
Overpressure: Environment: Knockout : 16 mm
Proof pressure: 25 kPa Operating temperature: Pressure fittings
Zero point calibration: -10...50 °C Male Ø 5.0 mm and 6.3 mm
Automatic autozero, manual pushbutton or via Modbus with autozero (-AZ) calibration -5...50 °C
register Storage temperature: Electrical
Response time: -20...70 °C Supply voltage:
1.0−20 s, selectable via menu or via Modbus register Humidity: 24 VAC or VDC ± 10 %
0 to 95 % rH, non condensing Power consumption:
Communication < 1.3 W
Protocol: MODBUS over Serial Line Physical Output signal:
Transmission Mode: RTU Dimensions: via Modbus
Interface: RS485 Case: 90.0 x 95.0 x 36.0 mm
Byte format (11 bits) in RTU mode: Weight: Conformance
Coding System: 8-bit binary 150 g Meets requirements for CE marking:
Bits per Byte: Mounting: EMC Directive 2014/30/EU
1 start bit 2 each 4.3 mm screw holes, one slotted RoHS Directive 2002/95/EY
8 data bits, least significant bit sent first Materials:
1 bit for parity Case: ABS
1 stop bit Lid: PC
Baud rate: selectable in configuration Duct connectors: ABS
Modbus address: 1−247 addresses selectable in Tubing: PVC
configuration menu Protection standard:
IP54

AZ-calibration is a function in the form of an automatic zeroing circuit built into the PCB The AZ adjustment takes 4 seconds. To avoid conflict with the BAS system, the output
board. The AZ-calibration electronically adjusts the transmitter zero at predetermined and display values will freeze to the latest measured value, after which the device
time intervals (every 10 minutes). The AZ-calibration eliminates all output signal drift returns to its normal measuring mode. Transmitters equipped with the AZ-calibration
due to thermal, electronic or mechanical effects, as well as the need for technicians to are virtually maintenance free.
remove high and low pressure tubes when performing initial or periodic transmitter zero
point calibration.

How to generate a model?

Example: Product series
DPT-FLOW-MOD-2500-AZ-D DPT-FLOW-MOD Air flow transmitter with Modbus communication

Highest available measurement range

-2500 0...2500 Pa

-7000 0...7000 Pa

Zero Point Calibration

-AZ With autozero calibration
Standard with pushbutton manual auto zero
Display
-D With display
Model DPT-FLOW-MOD -2500 -AZ -D

SENSOVANT www.sensovant.com Datasheet Version 3.0 2016