701z

 Package Content

Before starting to set up your camera, please make sure items below in your box:

QUICK GUIDE
QUICK GUIDE

Camera Bracket carabiner Quick Guide CD Manual

For more product details, please visit

 Installation
Step1: Loosen the screws on the dome cover to remove it (as shown in Figure 1), and Step4: Hook the camera and the bracket together with the supplied carabiner, and connect the
take all EPE foam rolls off in the camera. cables. Then, pull the cables from the other side of the bracket to hide the connectors
in the bracket.
NOTE: When you remove the EPE foam rolls, please be careful not to damage the inner
mechanism of the camera. Step5: Insert the camera to the bracket, and roate the camera a little bit to hook it. Then, use
a wretch to fasten the screws on the two sides of the bracket to secure the connection.
Step2: Install a microSD card if needed. Then, replace the cover back.
NOTE: Make sure the dome cover is clean without fingerprints before replacing it back.
Step3: Pass the cables to be connected through the bracket, and fasten the bracket to
the wall (as shown in Figure 2).

Figure 3 Figure 4
Figure 1 Figure 2

m583g_gh_quick_V0.9
 Insert a MicroSD Card  Default Values  Cable Overview
Step1: With the cover removed, find the microSD card slot
on the green board in the camera. Cable Description
IP address 192.168.1.10
Power cable DC12V, 1.5A power supply.
Step2: Insert the microSD card to the slot. Port number 88
Please do not insert the card forcedly. If you feel RJ45 network cable* Connect it to a RJ45 cable.
resistance, please try the other side. User name admin
GND Ground wire
Password admin
Note: It’s recommended to use a pair of tweezers for inserting / Reserved for external alarm device
Alarm-in
removing the microSD card. It's strongly recommended to change the default user connection
The data originally saved in the microSD card (if any) will be name and password before using the camera to keep your Alarm-out Reserved for external alarm device
removed after inserting it to the camera. account safe. connection
RESET Remove the insulating coating of wire,
The camera doesn’t support hot-swapping. Please insert or To change the default account, log into the camera, and go
and twist it with a ground wire together to
remove the microSD card with power disconnected. to Config.  General  Account. Create a new account,
reset default camera
and remove the default one.
Audio in Connect to a line-in device, i.e. a
microphone, for audio recording
Audio out Connect to a line-out device, i.e. speaker,
for audio output
* For PoE (IEEE802.3af) installation, make sure your network cable
has the maximum cable resistance of 20Ω, such as CAT.5e or CAT.6
cables, to conform to the standard of IEEE802.3af.

 Camera Configuration
Step1: Connect this camera to your NVR as described in “HD System Connection”. Step4: After searching, set your PC in the same network segment as the specific camera you
want to access, such as “192.168.30.xxx” (xxx could be 0~255) in our example
Step2: Connect PC to the HUB connected to your camera(s) with RJ45 network cable.
Step5: Note down the IP address and port number of the camera you want to access, such as
Step3: Search available devices with “IPScan.exe”; to download “IPScan.exe”, please visit
“192.168.30.1” and “88” in our example.
www.surveillance-download.com/user/IPscan.zip.
Step6: Open Internet Explorer on the PC, and enter the IP address and port number in the
URL column to access the camera. The format is http://ipaddress:portnum, such as
http://192.168.30.1:88 in our example.
Step7: Enter the default user name (admin) and password (admin) to access the camera.
Then, go to “Config” on the top right corner for more advanced configurations.