lOMoARcPSD|51487227

A Project Report on Arduino Radar FOR OB

EEE (COMSATS University Islamabad)

Scan to open on Studocu

Studocu is not sponsored or endorsed by any college or university

Downloaded by Akshay ([email protected])
 lOMoARcPSD|51487227

A Project Report
on
ARDUINO RADAR FOR OBJECT DETECTION

Submitted By:
I.D NUMBER STUDENT NAME
180060001 CH.KUSHWANT KUMAR
180060002 D.JETTY MARIYAN
180060003 T.SAI AVINASH

Sec-1, Batch-01

II/IV BACHELOR OF TECHNOLOGY

IN

ELECTRICAL AND ELECTRONICS ENGINEERING

(SEMESTER-IV)

KONERU LAKSHMAIAH EDUCATION FOUNDATION

VADDESWARAM-522502

APRIL 2020

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

Koneru Lakshmaiah Education Foundation

Analog Electronics Circuits and Design(18EC2103)
Electrical and Electronics Engineering

CERTIFICATE

This is to certify that the project report entitled “Arduino Radar for object detection” submitted by Mr.
CH.KUSHWANTH KUMAR-180060001 , D.JETTY MARIYAN-180060002, T.SAI AVINASH-
180060003 of section I studying II/IV B. Tech in EEE has satisfactorily completed project in the semester
IV during the academic year 2019 – 2020.

Signature of Course Instructor Signature of HOD

KASI UDAY KIRAN S.V.N. LALITHA

ii

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

ACKNOWLEDGEMENTS

We express great pleasure for me to express my gratitude to our honorable President Sri. Koneru
Satyanarayana, for giving the opportunity and platform with facilities in accomplishing the project based
laboratory. We express the sincere gratitude to our principal Dr. K. SUBBA RAO for his administration
towards our academic growth.
We express sincere gratitude to HOD-EEE DR. S.V.N. LALITHA successful completion of our
academic semester. We record it as my privilege to deeply thank for providing us the efficient faculty and
facilities to make our ideas into reality.
We express my sincere thanks to our project supervisor Mr. K. UDAY KIRAN for his novel
association of ideas, encouragement, appreciation and intellectual zeal which motivated us to venture this
project successfully.
We are pleased to acknowledge the indebtedness to our lab technicians all those who devoted
themselves directly or indirectly to make this project report success.
Last but not the least we express our deep gratitude and affection to our parents who stood behind
us in all our endeavours.

CH.KUSHWANT 180060001
D.JETTY MARIYAN 180060002
T.SAI AVINASH 180060003

iii

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

TABLE OF CONTENTS

S.NO CONTENTS PAGE NO

1. Abstract v

2. Introduction vi-viii

3. Principle or Methodology ix-x

4. Architecture of project xi

5. Components required xii-xiv

6. Working xv-xviii

7. Code xix-xxiv

8. Output xxv-xxvi

9. Advantages& conclusions xxvii-xxviii

10. References xxix-xxx

iv

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

ABSTRACT

Radar is an object detection system which uses radio waves to determine the range,
altitude, direction, or speed of objects. It can be used to detect aircraft, ships, spacecraft,
guided missiles, motor vehicles, weather formations, and terrain. The radar dish or antenna
transmits pulses of radio waves or micro waves which bounce off any object in their path.
The object returns a tiny part of the wave's energy to a dish or antenna which is usually located
at the same site as the transmitter.
The modern uses of radar are highly diverse, including air traffic control, radar
astronomy, air-defense systems, antimissile systems ;marine radar start locate landmarks
and other ships; aircraft anti-collision systems; ocean surveillance systems, outer space
surveillance and rendezvous systems; meteorological precipitation monitoring; altimetry
and flight control systems; guided missile target locating systems; and ground-penetrating
radar for geological observations. High tech radar systems are associated with digital signal
processing and are capable of extracting useful information from very high noise levels.
The Arduino based project requires a ultrasonic sensor, the sensor released the waves which
we want to measure the distance of a object. The microcontrollers of the Arduino board can
be programmed using C and C++ languages. When a code is written in Arduino UNO IDE
software and connected to the board through a USB cable, Arduino boards have lot of
applications in the present day scenario, so we have decided to do a small project on them.

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

INTRODUCTION

Defining Arduino: An Arduino is actually a microcontroller based kit which can be either used directly
by purchasing from the vendor or can be made at home using the components, owing to its open source
hardware feature. It is basically used in communications and in controlling or operating many devices.
1. Arduino is an open-source electronics platform based on easy-to-use hardware and software.
Arduino boards are able to read inputs - light on a sensor, a finger on a button, or a Twitter
message - and turn it into an output - activating a motor, turning on an LED, publishing
something online. You can tell your board what to do by sending a set of instructions to the
microcontroller on the board. To do so you use the Arduino programming language (based
on Wiring), and the Arduino Software (IDE), based on Processing.
2. Over the years Arduino has been the brain of thousands of projects, from everyday objects
to complex scientific instruments. A worldwide community of makers - students, hobbyists,
artists, programmers, and professionals - has gathered around this open-source platform, their
contributions have added up to an incredible amount of accessible knowledge that can be of
great help to novices and experts alike.
3. Arduino was born at the Ivrea Interaction Design Institute as an easy tool for fast
prototyping, aimed at students without a background in electronics and programming. As
soon as it reached a wider community, the Arduino board started changing to adapt to new
needs and challenges, differentiating its offer from simple 8-bit boards to products for IoT
applications, wearable, 3D printing, and embedded environments. All Arduino boards are
completely open-source, empowering users to build them independently and eventually
adapt them to their particular needs. The software, too, is opensource, and it is growing
through the contributions of users worldwide.

vi

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

1.1. How to program an Arduino ?

The Arduino tool window consists of the toolbar with the buttons like verify, upload, new, open, save, serial
monitor. It also consists of a text editor to write the code, a message area which displays the feedback like
showing the errors, the text console which displays the output and a series of menus like the File, Edit,
Tools menu. Thus the code is uploaded by the bootloader onto the microcontroller.

ULTRASONIC SENSOR

vii

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

1.1. ULTRASONIC SENSOR

As the name indicates, ultrasonic sensors measure distance by using ultrasonic waves.The sensor head
emits an ultrasonic wave and receives the wave reflected back from the target. Ultrasonic Sensors
measure the distance to the target by measuring the time between the emission and reception.
An optical sensor has a transmitter and receiver, whereas an ultrasonic sensor uses a single ultrasonic
element for both emission and reception. In a reflective model ultrasonic sensor, a single oscillator
emits and receives ultrasonic waves alternately. This enables miniaturization of the sensor head.
Distance calculation

The distance can be calculated with the following formula:

Distance L = 1/2 × T × C

Where L is the distance, T is the time between the emission and reception, and C is the sonic speed.
(The value is multiplied by 1/2 because T is the time for go-and-return distance.) Features
The following list shows typical characteristics enabled by the detection
system. [Transparent object detectable]
Since ultrasonic waves can reflect off a glass or liquid surface and return to the sensor head, even
transparent targets can be detected.
[Resistant to mist and dirt]

Detection is not affected by accumulation of dust

or dirt. [Complex shaped objects detectable]
Presence detection is stable even for targets such as mesh trays or springs.

viii

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

PRINCIPLE OR MEDTHODOLOGY

A radar system has a transmitter that emits radio waves called a radar signals in predetermined
directions. When these come into contact with an object they are usually reflected or scattered in many
directions Example:- let us take example for bat
Bat released the eco sound while travelling .if any object came in middle and it reflect back to the bat

Applications and usages:-

The development of the radar technology took place during the World War II in which it was used for
detecting the approaching aircraft and then later for many other purposes which finally led to the
development of advanced military radars being used these days. Military radars have a highly
specialized design to be highly mobile and easily transportable, by air as well as ground. Military radar
should be an early warning, altering along with weapon control functions. It is specially designed to be
highly mobile and should be such that it can be deployed within minutes.

ix

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

Here's a summary of how radar works:

• Magnetron generates high-frequency radio waves.

• Duplexer switches magnetron through to antenna.

• Antenna acts as transmitter, sending narrow beam of radio waves through the air.

Radio waves hit enemy airplane and reflect back.

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

ARCHITECTURE OF PROJECT:-

xi

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

PROCEDURE

Components Required:

In this project we have used the arduino and ultrasonic sensor along with the jumping wires and the relay
motors and details list of the hard ware components are
• Arduino board and arduino cable

• Jumper wires

xii

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

Bread board

Ultrasonic sensor

xiii

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

Relay motor

Double side plaster

gum gun

LAPTOP

xiv

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

WORKING

PRACTICAL IMPLEMENTATION

A. Making On Arduino Board

Since, we believe in learning by doing. So, we decided to make our own arduino board instead of using
the readymade board. So, the steps required to make an arduino board are as follows:
Boot-loading an Atmega328 using the Arduino board/AVR Programmer by uploading the boot loader
to the Microcontroller.
Making the connections on a general purpose PCB, connecting the crystal osicillator, capacitors,
connectors for the connections to Arduino board etc.
Providing the power supply, usually
5 volts. Arduino is Ready to use.
After you have done all this, then only the minimum circuitry like crystal oscillator, capacitors,
connectors, power supply is required to complete the board. The same circuit can be made on the PCB,
either designed or general purpose. Since, Arduino is an Open-Source. Hence, it is easy to make and
can have any enhancements as per the requirements.
B. Connecting Servo Motor

A servomotor is a rotary actuator that allows for precise control of angular position,
velocity and acceleration.
A normal servo motor has three terminals:

1.VCC

2. GND

3. PULSE

A servo motor works at normally 4.8 to 6 volts. Ground is provided by connecting it to the Ground of
the Arduino. The total time for a servo motor pulse is usually 20ms. To move it to one end of say 0
degree angle, a 1ms pulse is used and to move it to other end i.e 180 degrees, a 2ms pulse is applied.
Hence, according to this to move the axis of the servo motor to the center, a pulse of time 1.5 ms
should be applied. For this, the pulse wire of the servo motor is connected to the Arduino that provides
the digital pulses for pulse width modulation of the pulse. Hence, by programming for a particular
pulse interval the servo motor can be controlled easily.

xv

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

C. Connecting Ultrasonic Sensor:-

An Ultrasonic Sensor consists of three wires. One for Vcc, second for Ground and the third for pulse signal.

The ultrasonic sensor is mounted on the servo motor and both of them further connected to the Arduino

board. The ultrasonic sensor uses the reflection principle for its working. When connected to the Arduino,

the Arduino provides the pulse signal to the ultrasonic sensor which then sends the ultrasonic wave in

forward direction. Hence, whenever there is any obstacle detected or present in front, it reflects the waves

which are received by the ultrasonic sensor.

If detected, the signal is sent to the Arduino and hence to the PC/laptop to the processing software that

shows the presence of the obstacle on the rotating RADAR screen with distance and the angle at which it

has been detected.5

xvi

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

VI. USING PROCESSING SOFTWARE

VII.

Processing is an open source programming language and integrated development environment

(IDE) built for the electronic arts, new media art, and visual design communities with the
purpose of teaching the fundamentals of computer programming in a visual context, and to
serve as the foundation for electronic sketchbooks. The project was initiated in 2001 by Casey
Reas and Benjamin Fry, both formerly of the Aesthetics and Computation Group at the MIT
Media Lab. One of the stated aims of Processing is to act as a tool to get non-programmers
started with programming, through the instant gratification of visual feedback. The language
builds on the Java language, but uses a simplified syntax and graphics programming models.
VIII. PROBLEMS FACED

A. Making Own Arduino Board

The Arduino boards are available readily in the electronics market, but we decided to make our
own Arduino board instead of buying one. So, the first problem was where to start from to
achieve this goal. Since, all parts on an Arduino board are SMD’s, so we had to find a way to
replace the SMD’s with DIP IC’s and also had to make an AVR programmer in order to pursue
our further work. Hence, it took us some days to determine and plan our course of action.
After that we had to boot load the AVR chip so as to make it compatible with the Arduino

xvi

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

IDE software. Hence, we had to find a way to boot load the Arduino using the AVR
programmer. It took us a long time to make the AVR programmer by researching on the type
of communication and architecture of the AVR as it is not as same as a 8051 microcontroller.
B. Communicating with Arduino through PC

Another major problem related to the Arduino board was the communication with it from PC.
Since, there is a requirement of an RS-232 to TTL conversion for the communication, so try
some methods:
[1] Firstly I used the MAX-232 IC to communicate with the Arduino as with the 8051 but
due to large voltage drop and mismatch in the speed, it failed to communicate.
[2] Next, I tried to use a dedicated AVR as USB to Serial converter as in the original
Arduino board, the difference being DIP AVR used by us instead of the SMD Mega16U2
controller.
But, unfortunately I was unable to communicate through it.

[3] At last I had no other choice but to use the FTDI FT-232R chip for USB to Serial
conversion. Finally IT WORKED!!!

xvii

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

PROCESSING SOFTWARE:-

ARDUINO SOFTWARE :-

xviii

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

ARDUINO CODE
Includes the Servo library #include
<Servo.h>.
// Defines Tirg and Echo pins of the Ultrasonic Sensor
const int trigPin = 10; const int echoPin = 11;
// Variables for the duration and the distance
long duration; int distance;
Servo myServo; // Creates a servo object for controlling the servo motor
void setup() { pinMode(trigPin, OUTPUT); // Sets the trigPin as an Output
pinMode(echoPin, INPUT); // Sets the echoPin as an Input
Serial.begin(9600); myServo.attach(12); // Defines on which pin is the
servo motor attached
} void loop()
{
// rotates the servo motor from 15 to 165 degrees
for(int i=15;i<=165;i++){ myServo.write(i);
delay(30);
distance = calculateDistance();// Calls a function for calculating the distance measured by the
Ultrasonic sensor for each degree

Serial.print(i); // Sends the current degree into the Serial Port

Serial.print(","); // Sends addition character right next to the previous value needed later in
the Processing IDE for indexing
Serial.print(distance); // Sends the distance value into the Serial Port
Serial.print("."); // Sends addition character right next to the previous value needed later in
the Processing IDE for indexing
}
// Repeats the previous lines from 165 to 15 degrees
for(int i=165;i>15;i--){ myServo.write(i);
delay(30);

xix

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

distance = calculateDistance();
Serial.print(i);
Serial.print(",");
Serial.print(distance);
Serial.print(".");
}
}
// Function for calculating the distance measured by the Ultrasonic sensor int
calculateDistance(){

digitalWrite(trigPin, LOW);
delayMicroseconds(2);
// Sets the trigPin on HIGH state for 10 micro seconds
digitalWrite(trigPin, HIGH); delayMicroseconds(10);
digitalWrite(trigPin, LOW);
duration = pulseIn(echoPin, HIGH); // Reads the echoPin, returns the sound wave travel time in
microseconds distance= duration*0.034/2; return distance;
}

processer code:-
import processing.serial.*; // imports library for serial communication import
java.awt.event.KeyEvent; // imports library for reading the data from the serial port import
java.io.IOException;
Serial myPort; // defines Object Serial
// defubes variables
String angle="";
String distance="";
String data="";
String noObject;
float pixsDistance;
int iAngle,
iDistance; int
index1=0; int

xx

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

index2=0; PFont
orcFont; void setup()
{

size (1200, 700); // ***CHANGE THIS TO YOUR SCREEN RESOLUTION***

smooth();
myPort = new Serial(this,"COM5", 9600); // starts the serial communication
myPort.bufferUntil('.'); // reads the data from the serial port up to the character '.'. So actually it
reads this: angle,distance.
} void draw()
{

fill(98,245,31);
// simulating motion blur and slow fade of the moving line
noStroke(); fill(0,4);
rect(0, 0, width, height-height*0.065);

fill(98,245,31); // green color

// calls the functions for drawing the radar
drawRadar(); drawLine();
drawObject(); drawText();
} void serialEvent (Serial myPort) { // starts reading data from the Serial
Port
// reads the data from the Serial Port up to the character '.' and puts it into the String variable
"data". data = myPort.readStringUntil('.'); data = data.substring(0,data.length()-1);

index1 = data.indexOf(","); // find the character ',' and puts it into the variable "index1" angle=
data.substring(0, index1); // read the data from position "0" to position of the variable index1
or thats the value of the angle the Arduino Board sent into the Serial Port distance=
data.substring(index1+1, data.length()); // read the data from position "index1" to the end of the
data pr thats the value of the distance

xxi

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

// converts the String variables into Integer

iAngle = int(angle); iDistance =
int(distance);
}
void drawRadar() { pushMatrix(); translate(width/2,height-height*0.074); // moves
the starting coordinats to new location noFill(); strokeWeight(2); stroke(98,245,31);
// draws the arc lines
arc(0,0,(width-width*0.0625),(width-width*0.0625),PI,TWO_PI); arc(0,0,(width-
width*0.27),(width-width*0.27),PI,TWO_PI); arc(0,0,(width-width*0.479),(width-
width*0.479),PI,TWO_PI); arc(0,0,(width-width*0.687),(width-width*0.687),PI,TWO_PI);

// draws the angle lines line(-width/2,0,width/2,0); line(0,0,(-

width/2)*cos(radians(30)),(-width/2)*sin(radians(30))); line(0,0,(-
width/2)*cos(radians(60)),(-width/2)*sin(radians(60))); line(0,0,(-
width/2)*cos(radians(90)),(-width/2)*sin(radians(90))); line(0,0,(-
width/2)*cos(radians(120)),(-width/2)*sin(radians(120)));
line(0,0,(-width/2)*cos(radians(150)),(-width/2)*sin(radians(150)));
line((-width/2)*cos(radians(30)),0,width/2,0); popMatrix();
} void drawObject() { pushMatrix(); translate(width/2,height-height*0.074); // moves the
starting coordinats to new location strokeWeight(9); stroke(255,10,10); // red color
pixsDistance = iDistance*((height-height*0.1666)*0.025); // covers the distance from the
sensor from cm to pixels // limiting the range to 40 cms if(iDistance<40){
// draws the object according to the angle and the distance
line(pixsDistance*cos(radians(iAngle)),-
pixsDistance*sin(radians(iAngle)),(widthwidth*0.505)*cos(radians(iAngle)),-(width-
width*0.505)*sin(radians(iAngle)));
}
popMatrix();
} void drawLine() { pushMatrix(); strokeWeight(9); stroke(30,250,60);
translate(width/2,height-height*0.074); // moves the starting coordinats to new location
line(0,0,(height-height*0.12)*cos(radians(iAngle)),-(height-
height*0.12)*sin(radians(iAngle))); // draws the line according to the angle popMatrix();
}

xxii

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

void drawText() { // draws the texts on the screen

pushMatrix();
if(iDistance>40) { noObject
= "Out of Range";
} else { noObject =
"In Range";
} fill(0,0,0); noStroke(); rect(0, height-
height*0.0648, width, height);
fill(98,245,31); textSize(25);

text("10cm",width-width*0.3854,height-height*0.0833);
text("20cm",width-width*0.281,height-height*0.0833); text("30cm",width-
width*0.177,height-height*0.0833); text("40cm",width-
width*0.0729,height-height*0.0833); textSize(40); text ("Indian Lifehacker
", width-width*0.875, height-height*0.0277); text("Angle: " + iAngle +" °",
width-width*0.48, height-height*0.0277); text("Distance: ", width-
width*0.26, height-height*0.0277); if(iDistance<40) { text(" "
+ iDistance +" cm", width-width*0.225, height-height*0.0277);
} textSize(25); fill(98,245,60); translate((width-
width*0.4994)+width/2*cos(radians(30)),(height-
height*0.0907)width/2*sin(radians(30))); rotate(-radians(-60)); text("30°",0,0);
resetMatrix(); translate((width-width*0.503)+width/2*cos(radians(60)),(height-
height*0.0888)width/2*sin(radians(60))); rotate(-radians(-30)); text("60°",0,0);
resetMatrix(); translate((width-width*0.507)+width/2*cos(radians(90)),(height-
height*0.0833)width/2*sin(radians(90))); rotate(radians(0)); text("90°",0,0);
resetMatrix(); translate(width-width*0.513+width/2*cos(radians(120)),(height-
height*0.07129)width/2*sin(radians(120))); rotate(radians(-30));
text("120°",0,0); resetMatrix(); translate((width-
width*0.5104)+width/2*cos(radians(150)),(height-
height*0.0574)width/2*sin(radians(150))); rotate(radians(-60)); text("150°",0,0);
popMatrix();

xxiii

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

We create a variable analog and assign it to 0.This is because the voltage value we are going to

read is connected to the analog pin is A0. This voltage represents the voltage value falls across

the resistor value we are measuring. Next we create a variable name raw, which we will use to

read in the analog voltage value. This later is our code get assigned to the analogue read ()

function.

xxiv

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

Output: Screenshot

xxv

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

xxvi

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

ADVANTAGES:-

1. The cost effective : our project below 1000rs only.

2. Improvised accuracy: The resistors with low value in milliohms are used in advanced cars
with sensitive power steering and break circuits. Now a days these advancements have
become the major cause for the severe accidents . Therefore the components used in such
circuits must have accurate and precise value for smooth working of such circuits. Ultimately
this refers to the accurate testing of the resistors used. Improvised accuracy is thus the second
primary aim of the sensor.
3. Reduced hardware complexity: Hardware complexity is one of the reasons for the high cost
of the ultrasonic sensor. The use of arduino Uno is to reduce the motherboard present in the
conventional ohmmeter in arduino based ultrasonic sensor. The arduino acts as the central
board. Since arduino are readily available in market it leads to the reduction in the complexity
of the design. The automated range selection is also the objective in order to speedup the
testing process. This will also reduce the faults in range selection in manually operated
conventional sensor.

xxvii

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

CONCLUSIONS:-

This project aims on the use of Ultrasonic Sensor by connected to the Arduino UNO R3 board and the

signal from the sensor further provided to the screen formed on the laptop to measure the presence of any

obstacle in front of the sensor as well as determine the range and angle at which the obstacle is detected

by the sensor.

xxviii

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

REFERENCES

[1] http://www.arduino.cc/

[2] http://www.arduinoproducts .cc/

[3] http://www.atmel.com/atmega328/

[4] http://en.wikipedia.org/wiki/File:16MHZ_Crystal.jpg

[5] http://www.google.co.in/imgres?imgurl=http://www.electrosome.com/wp-

content/uploads/2012/06/ServoMotor.gif&imgrefurl=http://www.electrosome.com/tag/se

rvo

motor/&h=405&w=458&sz=67&tbnid=rcdlwDVt_x0DdM:&tbnh=100&tbnw=113&zoo

m=1

&usg= 6J2h0ZocdoSMrS1qgK1I2qpTQSI=&docid=lEfbDrEzDBfzbM&sa=X&ei=a_

OKU vTbD8O5rgeYv4DoDQ&ved=0CDwQ9QE

[6] http//:www.sproboticworks.com/ic%20pin%20configuration/7805/Pinout.jpg/

[7] http://www.sproboticworks.com/ic%ultrasonicsensor%20pinout.jpg

[8] http://www.instructables.com/id/ ATMega328-using-Arduino-/

[9] http://www.motherjones.com/files/blog_google_driverless_car.jpg

[10] http://www.google.co.in/imgres/Radar_antenna.jpg&w=546&h=697&ei=wuuK

[11] http://www.radomes.org/museum/photos/equip/ANSPS17.jpg [12]

http://www.wired.com/dangerroom/2011/07/ suicide- bombers-from-100-yards/

[13] http://upload.wikimedia.org/wikipedia/commons/Radaraccumulationseng.png

xxix

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

[14] http://arduino.cc/en/Tutorial/BarGraph/

[15] http://arduino.cc/en/Tutorial/LiquidCrystal/

[16] http://fritzing.org

xxx

Downloaded by Akshay ([email protected])

 lOMoARcPSD|51487227

xxxi

Downloaded by Akshay ([email protected])