ATD Software Manual

P/N 1224-500 Rev. H-12/4/01

X-RITE SOFTWARE LICENSE AGREEMENT
This is a legal agreement between you (either an individual or an entity) and X-Rite, Incorporated.
By opening the sealed software packets(s) you are agreeing to be bound by the terms of this
agreement. If you do not agree to the terms of this agreement, X-Rite and its suppliers are
unwilling to grant you a license to use the software, and you may not use the software. You may,
however, promptly return the unopened software packet(s) and the accompanying items (including
written materials and binders or other containers) to the place you obtained them for a full refund.

1. GRANT OF LICENSE
X-Rite grants to you the right to use one copy of the enclosed X-Rite software product (“SOFTWARE”)
on a single computer. The SOFTWARE is in “use” on a computer when it is loaded into temporary
memory (i.e. RAM) or installed into permanent memory (e.g. hard disk, CD-ROM, or other storage
device) of that computer. However, installation on a network server for the sole purpose of distribution to
one or more other computer(s) shall not constitute “use” for which a separate license is required. The
license granted herein transfers neither title nor proprietary rights to you with respect to the SOFTWARE
2. COPYRIGHT
The SOFTWARE is owned by X-Rite or its suppliers and is protected by United States copyright laws
and international treaty provisions. Therefore, you must treat the SOFTWARE like any other
copyrighted material (e.g. a book or musical recording) except that you may either (a) make one copy of
the SOFTWARE solely for backup or archival purposes, or (b) transfer the SOFTWARE to a single hard
disk provided you keep the original solely for backup or archival purposes. You may not copy the written
materials accompanying the SOFTWARE, and you may not remove the labels or proprietary legends
from the SOFTWARE or its documentation. All rights not specifically granted under this agreement are
retained by X-Rite.
3. TRANSFER/LIMITATIONS
This agreement is your proof of license to exercise the rights granted herein and must be retained by you.
You may not rent, lease or sublicense the SOFTWARE, but you may transfer the SOFTWARE and
accompanying written materials on a permanent basis provided you retain no copies and the recipient
agrees to the terms of this License Agreement. If the SOFTWARE is an update or has been updated, any
transfer must include the most recent update and all prior versions. You may not reverse engineer,
decompile or disassemble the SOFTWARE.
4. MULTIPLE ENVIRONMENT SOFTWARE/MULTIPLE LANGUAGE SOFTWARE/DUAL
MEDIA SOFTWARE/MULTPLE COPIES/UPGRADES
If the package contains, or, in connection with the acquisition of the Software contained
in this package you receive, two or more operating environment versions of the
SOFTWARE (e.g., Macintosh® and Windows®) two or more language translation
versions of the SOFTWARE, the same SOFTWARE on two or more media (e.g.,
diskettes and a CD-ROM), and/or you otherwise receive two or more copies of the
SOFTWARE, the total aggregate number of computers on which all versions of the
SOFTWARE are used may not exceed the primary computer as described above. You
may make one back-up copy, in accordance with the terms of this Agreement.
5. LIMITED WARRANTY
X-Rite warrants that the SOFTWARE will perform substantially in accordance with the accompanying
written materials for a period of ninety (90) days from the date of receipt. This limited warranty
(“Limited Warranty”) is expressly conditioned on your observance of the operating procedures set forth
in the documentation. X-Rite shall not be obligated to correct, cure, or otherwise remedy any
nonconformity or defect in the SOFTWARE if you have made any changes to, misused, or damaged the
SOFTWARE.
6. LIMITED WARRANTY
X-Rite warrants that (a) the SOFTWARE will perform substantially in accordance with the
accompanying written materials for a period of ninety (90) days from the date of receipt, and (b) any
hardware accompanying the SOFTWARE will be free from defects in materials and workmanship under
normal use and service for a period of one (1) year from the date of receipt. Any implied warranties on
the SOFTWARE and hardware are limited to ninety (90) days and one (1) year respectively. Some
states/countries do not allow limitations on duration of an implied warranty, so the above limitation may
not apply to you.
X-RITE AND ITS SUPPLIERS DISCLAIM ALL OTHER WARRANTIES, EITHER EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NON-
INFRINGEMENT WITH REGARD TO THE SOFTWARE, THE ACCOMPANYING WRITTEN
MATERIALS, AND ANY ACCOMPANYING HARDWARE.
7. CUSTOMER REMEDIES
X-Rite’s and its suppliers’ entire liability and your exclusive remedy shall be, at X-Rite’s option, either
(a) return of the price paid, or (b) repair or replacement of the SOFTWARE or hardware that does not
meet X-Rite’s Limited Warranty and which is returned to X-Rite with a copy of your receipt. The
Limited Warranty does not apply if failure of the SOFTWARE has resulted from accident, abuse, or
misapplication. Any replacement SOFTWARE or hardware will be warranted for the remainder of the
original warranty period or thirty (30) days, whichever is longer. Outside the United States, these
remedies are not available without proof of purchase from an authorized non-U.S. source.
8. NO LIABILITY FOR CONSEQUENTIAL DAMAGES
IN NO EVENT SHALL X-RITE OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES
WHATSOEVER (INCLUDING, WITHOUT LIMITATION, SPECIAL, INCIDENTAL,
INDIRECT AND CONSEQUENTIAL DAMAGES FOR LOSS OF BUSINESS PROFIT,
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER
PECUNIARY LOSS) ARISING OUT OF THE USE OF OR INABILITY TO USE THE
SOFTWARE, EVEN IF X-RITE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. IN ANY CASE, X-RITE’S ENTIRE LIABILITY UNDER ANY PROVISION OF
THIS AGREEMENT SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID BY YOU
FOR THE SOFTWARE. BECAUSE SOME STATES/COUNTRIES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
9. U.S. GOVERNMENT RESTRICTED RIGHTS
The SOFTWARE and documentation are provided with RESTRICTED RIGHTS. Use, duplication, or
disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1) and (ii) of the
Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 or subparagraphs (c)(1)
and (2) of the Commercial Computer Software – Restricted Rights at 48 CFR 52.227-19, as applicable.
If you acquired this product in the United States, this Agreement is governed by the laws of the State of
Michigan.

Should you have any questions concerning this Agreement, please contact: X-Rite, Incorporated 3100
44th Street S.W./Grandville, MI 49418/Phone 616-534-7663, Fax 616 534-2513.

Copyright  1999 by X-Rite, Incorporated

“ALL RIGHTS RESERVED”
X-Rite and X-Tract are registered trademarks of X-Rite, Incorporated
PANTONE® Computer Video simulations used in this product may not match PANTONE-identified solid
color standards. Use current PANTONE Color Reference Manuals for accurate color.
All trademarks noted herein are the property of X-Rite, Inc., Pantone, Inc., or their respective companies.
“PANTONE Color Reflectance Software” © Pantone, Inc. 1991, 1994.
Pantone, Inc. is the copyright owner of PANTONE Color Reflectance Software which is licensed to X-
Rite, Incorporated to distribute for use only in combination with Auto Tracking Spectrophotometer
Software. PANTONE Color Reflectance Software shall not be copied onto another diskette or into
memory unless as part of the execution of the Auto Tracking
Spectrophotometer Software.
 Table Of Contents
Getting Started with ATD
Installing the Software......................................................................................................................1-1
Starting the Software .......................................................................................................................1-1
What To Do First .............................................................................................................................1-1

The ATD User Interface

Using the Control Pane ....................................................................................................................2-1
Using the Toolbar ............................................................................................................................2-2
Using the Status Bar ........................................................................................................................2-2
Using the Main Menus .....................................................................................................................2-2
Using the Desktop ...........................................................................................................................2-2

Working with Your Instrument

Setting Up Your Instrument ..............................................................................................................3-1
Calibrating your Instrument...............................................................................................................3-1
Calibrating the Scanning Instrument............................................................................................3-1
Calibrating the Scanning Instrument Track ..................................................................................3-1
Instrument Diagnostics.....................................................................................................................3-2

Setting up the Software Options

General tab .....................................................................................................................................4-1
Defaults tab .....................................................................................................................................4-1
Post Scan tab..................................................................................................................................4-2
Network tab .....................................................................................................................................4-3
File Formats tab...............................................................................................................................4-3
Reports tab .....................................................................................................................................4-4
Restrictions tab................................................................................................................................4-4

Using the ATD Libraries

Using the Library Manager dialog boxes ............................................................................................5-1
Duplicating a Library Item...........................................................................................................5-1
Deleting a Library Item ...............................................................................................................5-2
Setting a Default Library Item .....................................................................................................5-2
Printing a Library Item Report.....................................................................................................5-2
Importing a Library Item .............................................................................................................5-2
Exporting a Library Item .............................................................................................................5-2
The Presses Library.........................................................................................................................5-3
Creating and Editing Presses .....................................................................................................5-3
The Color Bars Library.....................................................................................................................5-4
Requirements for Creating Color Bars.........................................................................................5-4
Creating and Editing Color Bars..................................................................................................5-5
Adding a Patch to a Color Bar.....................................................................................................5-5
Rearranging Patches on the Color Bar ........................................................................................5-6
Defining Individual Patches (Color Bars)......................................................................................5-6
The Colors Library ...........................................................................................................................5-7
Adding Colors from Other Libraries to the User Color Library........................................................5-7
Adding Colors to the Scanned Color library .................................................................................5-7
Renaming Colors in the User Color Library..................................................................................5-7

i
 Removing Colors from the User Color Library..............................................................................5-8
Importing Colors into the User Color Library ................................................................................5-8
Searching for a Color Name .......................................................................................................5-8
Selecting Ink Colors ...................................................................................................................5-9
The Tags Library .............................................................................................................................5-9
Creating and Editing Tags ........................................................................................................5-10
Creating and Editing User Tag Groups ......................................................................................5-10
Deleting a Tag or User Tag Group ............................................................................................5-10
Add or Remove Tags dialog box...............................................................................................5-11
The Target and Tolerance Libraries ................................................................................................5-11
Creating and Editing Shop Targets ...........................................................................................5-11
Creating and Editing Shop Tolerances ......................................................................................5-12

Working with Project and Jobs

Creating Projects .............................................................................................................................6-1
Deleting Projects .............................................................................................................................6-1
Renaming Projects ..........................................................................................................................6-2
Creating a New Job .........................................................................................................................6-2
Creating a Job Based on an Existing Job ..........................................................................................6-2
Opening Existing Jobs .....................................................................................................................6-3
Copying Jobs ..................................................................................................................................6-3
Deleting Jobs ..................................................................................................................................6-3
Moving Jobs ....................................................................................................................................6-3
Renaming Jobs ...............................................................................................................................6-4
Importing Jobs .................................................................................................................................6-4
Exporting Jobs.................................................................................................................................6-4
Sending Jobs via E-Mail...................................................................................................................6-5
Creating Job Extract Files ................................................................................................................6-5
Job Status dialog box.......................................................................................................................6-5

Setting Up Your Job

Press dialog box..............................................................................................................................7-1
Manage Keys dialog box ............................................................................................................7-2
Color Bars dialog box.......................................................................................................................7-2
Adding Color Bars to a Sheet Edge.............................................................................................7-2
Removing Color Bars from a Sheet Edge ....................................................................................7-3
Changing Color Bars on a Sheet Edge ........................................................................................7-3
Moving a Color Bar to a Different Sheet Edge ..............................................................................7-3
Summary dialog box ........................................................................................................................7-3
Targets and Tolerances dialog box ...................................................................................................7-4
Manually Defining Target and Tolerance values ...........................................................................7-4
Job Targets and Tolerances dialog box.......................................................................................7-4
Enable All Computations dialog box............................................................................................7-6
Identification dialog box....................................................................................................................7-6
Job Properties dialog box.................................................................................................................7-7

Recognizing Your Job

Select Recognition Type dialog box ..................................................................................................8-2
Select Color Bars dialog box.............................................................................................................8-2
Find Color Bars dialog box ...............................................................................................................8-2
Specify Color Bar Position dialog box................................................................................................8-3
Scan and Recognize dialog box........................................................................................................8-3
Adjust Repeats dialog box..........................................................................................................8-4
Adjust Patches dialog box ..........................................................................................................8-4

ii
Reposition Sheet dialog box .............................................................................................................8-4
Final Results dialog box ...................................................................................................................8-4

Measuring Your Job

Measure Color Bar dialog box...........................................................................................................9-1
Reposition Sheet dialog box .............................................................................................................9-1

Retargeting Your Job

Retargeting the Job to the Current Sheet.........................................................................................10-1
Resetting the Job to Original Target Values.....................................................................................10-1
Manually Defining New Target Values.............................................................................................10-1
Changing the State of a Job ...........................................................................................................10-2

Retolerancing Your Job

Manually Defining New Tolerance Values........................................................................................11-1
Enabling and Disabling Tolerance Types .........................................................................................11-1

Viewing Job Data

The View Types.............................................................................................................................12-1
Using the Key Trend View........................................................................................................12-1
Using the Sheet Trend View .....................................................................................................12-2
Using the Press Status View.....................................................................................................12-2
Using the Zoom Mode..............................................................................................................12-3
Customizing Views and Graphs ......................................................................................................12-3
Adding a Graph to the Current View..........................................................................................12-3
Adding Multiple Graphs to the Current View...............................................................................12-4
Changing the Current Graph.....................................................................................................12-4
Removing Graphs from the Current View ..................................................................................12-4
Moving Through Graphs...........................................................................................................12-4
Selecting the Sheet Range .......................................................................................................12-4
Moving Through Sheets ...........................................................................................................12-5
Moving to a Specific Sheet .......................................................................................................12-5
Selecting the Key Range ..........................................................................................................12-5
Moving Through Keys ..............................................................................................................12-6
Moving to a Specific Key ..........................................................................................................12-6
Turning Keys On and Off..........................................................................................................12-6
Showing Key Trend Values ......................................................................................................12-6
Printing Graph Data .................................................................................................................12-6
Increasing and Decreasing Vertical Scaling ...............................................................................12-7
Displaying Difference or Actual Data .........................................................................................12-7
Using Full Screen view.............................................................................................................12-7

Printing Job Data

Using Custom Reports ...................................................................................................................13-1
Generating a Custom Report ....................................................................................................13-1
Adding or Editing a Custom Report ...........................................................................................13-1
Deleting a Custom Report ........................................................................................................13-2
Using the Job Summary Report ......................................................................................................13-2
Page Header ...........................................................................................................................13-2
Job Information........................................................................................................................13-3
Summary of All Computations and All Inks ................................................................................13-3
Summary of All Totals ..............................................................................................................13-3

iii
 Ending Percentages.................................................................................................................13-4
Using the Single Sample Single Attribute Report..............................................................................13-4
Page Header ...........................................................................................................................13-4
Sample Information ..................................................................................................................13-4
Key Data.................................................................................................................................13-5
Statistics .................................................................................................................................13-5
Using the Trend Analysis Report.....................................................................................................13-5
Page Header ...........................................................................................................................13-6
Patch Information ....................................................................................................................13-6
Statistical Information ...............................................................................................................13-7
Data........................................................................................................................................13-7
Graph .....................................................................................................................................13-7
Statistical Process Control Program................................................................................................13-7
Print File Utility ..............................................................................................................................13-7

iv
 SECTION ONE

1. Getting Started with ATD

The ATD software drives your Scanning Spectrophotometer instrument. It allows you to easily
organize each press run measurement according to project, job, and measured standards. ATD comes
with pre-loaded libraries for different press specifications, colors, and color bars.

INSTALLING THE SOFTWARE

NOTE: Some users of this software purchased turn-key systems with a pre-installed application. These
users can use the following instructions if they need to re-install the software from their backup CD.
The ATD software uses a standard Windows installation procedure.

To install ATD:
1. Insert the ATD CD into your computer's CD-ROM drive. The install program will start
automatically.
NOTE: If the install program does not start automatically, choose Run from the Windows Start
menu, then type "d:\setup.exe", where "d" = your system's CD-ROM drive.
2. Follow the Install wizard prompts to start the software setup program.
3. Follow the instructions for a Full installation.

STARTING THE SOFTWARE

Before starting the Software, you should take a moment to check your display driver’s color settings.
For optimal representation of on-screen color simulations, your display driver should be set up for at
least High Color (16 bit) resolution.
To check your display driver settings:
1. From the Windows Start menu, choose Settings, then choose Control Panel.
2. Double-click the Display program icon in the Control Panel directory. The Display Properties
dialog box appears.
3. At the top of the Display Properties dialog box, click the Settings tab.
4. From the Color Palette list, select either High Color (16 bit) or True Color (24 bit). If neither of
these settings is available, your display driver does not support these resolution settings.
Once the Software is installed on your computer, you can start it by double-clicking the Program Icon
located in the Software’s directory, or by selecting the item from the appropriate program folder on the
Windows Start menu.
NOTE: You can create a shortcut to ATD on the Windows desktop by dragging the ATD program
Icon onto the desktop.
As it opens, the Software checks your display driver settings. If you are not running at 16-bit resolution
or better, a Warning message appears that informs you of the 16-bit resolution recommendation. Click
Close to continue.

WHAT TO DO FIRST
The first time you open the software, the Select Job dialog box appears. You can use the buttons on
the Select Job dialog box to create a new job, open an existing job, import a job, or close the
application.

1-1
SECTION ONE

Once you open a job, you can use the rest of the software. The ATD user interface includes the Control
Pane, display area, menu bar, toolbar, and status bar.
Before you can actually begin recognizing and measuring jobs, you need to set up your instruments.

1-2
 SECTION TWO

2. The ATD User Interface

ATD uses standard Windows conventions, such as menus and submenus, toolbar buttons, list boxes,
option buttons, and check boxes. If you are unfamiliar with the basic functions of the Windows
environment, refer to your Windows documentation.
The user interface consists of the Control Pane, the menu bar, the toolbar, the status bar, and the
display area (Desktop area).

USING THE CONTROL PANE

The Control Pane is located along the left side of the Main Window. You can display or remove the
Control Pane by choosing Control Pane from the View menu (a check mark appears next to the
command when the Control Pane is displayed). Use the tools on the Control Pane to measure, view,
and evaluate job and sheet data.
NOTE: If you are working on a satellite workstation, you will not have access to all of the tools listed
below.
· Sheet Status. A color-coded indicator above the Status button indicates the status of the current
sheet: OK = green; Action = yellow; Control = red. Click the Status button to open the Job Status
dialog box, where you can review detailed status information.
· Color Bar Information. Click the Color Bar button to open the View Color Bar dialog box.
This dialog box shows the color bar information from the most recent scan.
· Retarget. Click the Retarget button to open the Retarget dialog box, where you can set up new
target values for the current job.
· Retolerance. Click the Retolerance button to open the Retolerance dialog box, where you can
set up new tolerances for the current job.
· Delete. Click the Delete button to delete the current sheet. The system asks if you are sure you
want to delete the sheet. Click Yes to confirm the deletion.
· Note. Click the Note button to open the Note Editor dialog box, where you can enter text
comments about this sheet. Click OK to save your comments and close the dialog box. (A note
icon appears next to the Note button for sheets that have notes.)
· Tags. Click the Tags button to open the Add or Remove Tags dialog box, where you can assign
tags to the current sheet.
· Sheet Slider. Move the slider to the right and left to move through all sheets in the job. Above the
slider, indicators display the date and time the sheet was measured and the number of the sheet in
relation to the total sheets in the job (such as “5 of 10”).
· Recognize. This button only appears if you have not recognized the current job. Click Recognize
to start the Recognition wizard.
· Measure. This button only appears if you have already recognized the current job. Click Measure
to start the Measurement wizard.
· Key Slider. Move the slider to the right and left to move through all keys in the job. The number
of the current key appears above the slider.
· Graph Controls. Use the graph controls to select how you want data to appear in the current job
window. Click All Difference if you want to display difference data (variation from the target
values). Click All Actual if you want to display actual data.

2-1
SECTION TWO

USING THE TOOLBAR

The toolbar buttons provide shortcuts to several functions in the Software. You can display or remove
the Toolbar buttons by choosing Toolbar from the View menu (a check mark appears next to the
command when the Toolbar is displayed). To identify the function of a specific toolbar button, place
your mouse cursor over the button and pause. A tool tip identifies the name of the button, and a
description of the related function appears on the status bar.

USING THE STATUS BAR

The status bar at the bottom of the window provides descriptive information about menu commands
and toolbar buttons, displays the sheet and key range, and identifies the current graph scale factor. To
turn the status bar on and off, choose Status Bar from the View menu. When the status bar is turned
on, a check mark appears next to the menu command. The status bar displays the following types of
information:
· Item Description and System Status
To view a description of a menu command, toolbar button, or Control Pane item, place your
mouse cursor over the item and pause. The left portion of the status bar provides a brief
description of the current item.
· Sheet and Key Range
The current sheet range and key range in use appear in the Sheet and Key fields..
· Graph Scale Factor
The far right field of the status bar displays the graph scale status— the current level of vertical
scaling.

USING THE MAIN MENUS

All of the ATD menus provide access to the different functions of the software. Many of these
functions are also accessible through other tools in the software. For example, you can change the view
type in a job window by selecting a different view tab or by choosing a different command from the
View menu.
Each menu operates according to standard Windows conventions. You can open menus and submenus
by clicking the menu or submenu command. Choose the desired command from those that are
displayed.
You can also open menus and choose commands using shortcut keys (shortcut keys are underlined in
the menu or command name). To open a menu, press ALT + [shortcut key]. To choose a command
from an open menu, you only need to press the shortcut key. For example, to open the Job menu, press
ALT + J. To choose the New command, press N.
NOTE: When you highlight a menu item, a description of the function appears in the Status bar at the
bottom of the application screen.

USING THE DESKTOP

The system displays your job data on the ATD desktop. Measurement data for each job is shown in a
separate job window. Within a job window, you can display a different type of data by changing the
view type and adding or removing graphs.

2-2
 SECTION THREE

3. Working with Your Instrument

SETTING UP YOUR INSTRUMENT

Before you can use the scanning instrument, you must set up the instrument so that the software can
properly read the instrument data. You can configure your instrument on the Instruments tab of the
Options dialog box.
NOTE: If you have not properly connected the instrument to your computer or performed the
following configuration steps, an error message appears when you start a measurement. Refer to your
instrument documentation for specific instructions on how to connect the scanning instrument.

To configure your instruments:

1. From the Instrument menu, choose Configure. The Instruments tab of the Options dialog box
appears.
2. Select the Scanning Instrument check box.
3. Click the Configure button to open the Select Transport dialog box. From the Available
Transport list, select the port to which your scanning instrument is connected. Click OK to save
your setting and return to the Options dialog box.
4. Click OK to save your instrument settings and close the Options dialog box.
NOTE: You can perform firmware updates using the Instrument Diagnostics dialog box.

CALIBRATING YOUR INSTRUMENT

To ensure accurate and reliable measurements, you should calibrate your instrument every day that it is
used. The ATD software keeps track of each the instrument's calibration status. The software
automatically starts the calibration process every 24 hours.

Calibrating the Scanning Instrument

Every 24 hours (since the most recent automatic calibration), the system pauses briefly to calibrate the
scanning instrument. If you are performing a measurement at this time, the system waits until your
measurement is complete before it attempts to calibrate the scanning instrument.
When the system automatically calibrates the scanning instrument, it displays the Instrument
Calibration dialog box. Allow the calibration procedure to continue. When the calibration process is
complete, the dialog box automatically closes.
To manually start the calibration process, choose Calibrate from the Instrument menu.
NOTE: The software prompts you to clean the calibration plaques located in the track before a
calibration can be performed. Refer to your instrument operation manual for instructions on cleaning
the plaques.

Calibrating the Scanning Instrument Track

Over time, the characteristics of the scanning track surface may change due to dirt buildup, cleaning
methods, etc. You will know that a track calibration is required if the following symptoms occur:
· Black data is read before paper data when the system tries to recognize a color bar.
· The scanning head accelerates immediately after leaving the docking station, rather than searching
for the edge of the paper first.

3-1
SECTION THREE

To calibrate the scanning track:

1. From the Instrument menu, choose Scanning, then choose Calibrate Track.
2. The system prompts to you to clean the track area and remove the press sheet. Click OK after you
complete these tasks.
3. The system performs the track calibration. When the calibration is finished, the dialog box
automatically closes.

INSTRUMENT DIAGNOSTICS
The Instrument Diagnostics dialog box provides information regarding the instrument scanning head,
docking station, and scanning software. You can this dialog box to perform firmware updates.
From the Instrument menu, choose Diagnostics to open the dialog box. You can also open the dialog
box by double-clicking the Instrument Diagnostics icon in the program group.
The following information appears on the dialog box:
· Scanning Instrument Information. The version numbers for the current firmware and system
configuration data appear here. If necessary, click Find Instrument to have the system look for
your instrument on your computer’s COM ports. You can click Write Configuration to File to
output the instrument configuration to a file for advanced troubleshooting. Additional diagnostic
support comes in the form of a log file to which instrument warning and error messages are
written.
· Scanning Instrument Firmware. Use the options and buttons in this area to update to a new
version of firmware for the scanning head and docking station. To install new firmware, select the
appropriate option (Head or Station) and click Install New Version. If necessary, you can return
to the previous version of firmware by selecting the appropriate option and clicking Install
Previous Version.
· Scanning Instrument Calibration. Whenever the track or scanning head is replaced, calibration
plaque values that exist in the docking station memory must be adjusted. Click Set Calibration
Plaque Values to update those values. If necessary, you can also calibrate the scanning instrument
and scanning instrument track by clicking Calibrate and Calibrate Track, respectively.

3-2
 SECTION FOUR

4. Setting up the Software Options

Before you being setting up, measuring, and evaluating a new job, you need to set up the different
software options. You can select your options using the Options dialog box. From the Tools menu,
choose Options to open the dialog box. Each tab on the dialog box allows you to define parameters for
a different aspect of the software.
NOTE: If restrictions are set up, you will only have access to the Instruments tab. To disable any
restrictions and view the remaining tabs, choose Restrictions from the Tools menu. You must then
enter the correct password to disable the restrictions.
When working in the Options dialog box, you can change the settings on any of the available tabs.
When you are satisfied with your selections, click OK to save the new settings and close the dialog
box. You can also click Apply to save your changes without closing the dialog box.

GENERAL TAB
Use the General tab to define application startup defaults and other software parameters, as follows:
· Select the Lock main window in the maximized state check box if you want to lock the size of
the main application screen. When this check box is selected, the screen size will maximize to
display across your entire computer screen whenever the application is opened. When the screen
size is locked in this way, you must use the shortcut keys (ALT + F4) to exit the application.
· Determine how you want to display graphs when a job is first opened (you can change the display
settings after the job is opened). Select Show a default graph for each ink in the Job if you want
to display a solid ink density graph for each ink in the job. Select Show the most recently used
graphs in the job to show the graphs that you were using when you last closed the job. Select
Show no graphs if you want the current job window to remain empty until you manually select
specific graphs for display.
· Select how you want to enter and display unit amounts: in English or Metric measurements.
· Select the default calculation method for graph information. Select Absolute if you want to
calculate and display graph information with the paper (substrate) data included. Select Minus
Paper if you want to calculate and display graph information without the paper data.
· In the Max Trend Graphs (per page) box, type the maximum number of Trend graphs to display
in a single job window, or use the arrow buttons to select the maximum number. You can view up
to eight Key trend or Sheet trend graphs simultaneously in a maximized job window. If you select
more than eight graphs, you must use the scroll bar to view some of the graph data. With more
graphs displayed in a single job window, less detail is provided on each individual graph.
· Select the Show numbers on key trend graphs check box if you want to display the actual value
of each key within that key bar.
· In the Company Name box, type a name to appear in the header of all printed reports.
· From the Default Status list, select the default status to use when calculating densitometric limits
and displaying density graphs.

DEFAULTS TAB
Use the Defaults tab to set up the default parameters for sheet, job, and recognition/measurement
controls, as follows:

4-1
SECTION FOUR

• Select the Retarget All Sheets Whenever Targets change check box if you only want to use one
set of target values for each job. This means that whenever you change the target values, the
system retargets all of the existing sheets to the new values. If there was a previous OK sheet, that
sheet is changed from an OK sheet to a makeready sheet. If you do not select this check box, the
system uses the new target values for future sheets only.
• Enter the default sheet width to use when creating new jobs. Type the desired width in the Width
box, or use the arrow buttons to select the width.
• Select the default location of the color bar on a sheet edge. If you center your sheet on the press,
select Centered. If you do not center the sheet, select Left edge on key, and then type the key
number corresponding to the left edge of the sheet.
• Select the Use "based on" jobs check box to have the related check box automatically selected in
the New Job dialog box. When this is selected, all new jobs are initially based on a previous job.
You can change this option when you create a new job.
• Select the Watch only density during makeready check box if you only want to use density
computations during a makeready phase. If this option is selected, it is used by default when you
set up a new job (when setting up targets and tolerances for the job, you can only define the
Density target values and tolerance limits).
• Select the Adjust for stock thickness check box if you want the system to prompt you to measure
the stock (sheet) during a recognition sequence. This option can be changed during recognition.
• Select the Use recognition scans as first sheet in Job check box if you want the system to use the
measurement data taken from the recognition process as an actual sheet for your job. When this
check box is selected, the system will automatically create a sheet based on the recognition scan.
• Select the Automatically advance to the next step of the recognition wizard (if possible) check
box if you want the software to automatically move to each step in the recognition/measurement
wizards. At those steps in the wizards where no additional input is required from the user, the
system will automatically display the next dialog box.
• In the Minimum recognition percentage box, type the minimum percentage considered
acceptable for the amount of patch recognized on a scan, or use the arrow buttons to select the
desired percentage. If the amount of patches recognized is less than this percentage, the wizard
will require user intervention before proceeding to the next step.

POST SCAN TAB

Use the Post Scan tab to automatically generate output data after a sheet measurement, as follows:
• Select the Print a Single Sample, Single Attribute report after each measurement check box
to automatically generate a report for solid ink density immediately after each measurement is
completed.
• Select the Create Scan Density File check box to automatically generate a density report for each
patch of the color bar. The report is then output to a specified file location after every
measurement. If you select this check box, you must enter the file name and directory location to
which the scan density file information should be written. In the Filename box, type the file
information or click the Browse button (…) to select the location from a directory dialog box. If
you want each new report to be appended to this file, select the Append check box. If you want
each new report to overwrite the previous report, make sure this check box is not selected.
• Select the Create a Scan Value File (SVF) check box to create a Scan Value File. The Scan Value
File consists of job information plus densitometric, colorometric and spectral data for each patch
scanned. If you select this check box, you must enter the file name and directory location to which
the Scan Value File should be written. In the Filename box, type the file path or click the Browse
button (…) to select the location from a directory dialog box

4-2
 SETTING UP THE SOFTW ARE OPTIONS

NETWORK TAB
The networking feature supports remote operation for the monitoring of press jobs, allowing a single
instrument to be shared among several presses. Any Windows -compatible network can support a
satellite workstation.
The master system operates in the same manner as any normal, stand-alone system. A satellite
(remote) workstation operates under the following restrictions:
· No recognitions can be performed.
· No measurements can be performed.
· No retargeting or retolerancing can be performed.
· Color bars cannot be edited.
· Sheets cannot be deleted.
On the Network tab, you select the type of system that you are using and define the location of the
master database directory.
· If you are using a networked system, select the Network check box. This activates the remaining
items on this tab.
· Select the type of workstation that you are using: Master or Satellite.
· The database for the master and satellite workstations is set to the master system's database. All
satellite data is stored on the master database. To change the default database directory, enter the
path of the directory in the appropriate box, or click the Browse button (…) to select the directory
location from a directory dialog box. You can then select the directory location from any folder on
any available directory or shared network drive.

FILE FORMATS TAB

The settings on the File Formats tab allow you to exchange press densitometric data between “on-
board” scanning systems and a print data analysis (PDA) program. The Print Data Exchange File
Format function generates the file format—a cross-platform, device-independent file specification—
used for this data exchange.
The PDA file structure includes a header portion, followed by the data. This header contains the file
location, project name, job name, status, and a user-defined comment. The data is organized by sheets
and “alleys.” A line of data is provided for each sheet, and each sheet is divided into alleys. An alley,
measured in keys, consists of data from each color in the job. For each color, the file lists values for
three density measurements, print contrast, and dot gain.
Since the keys are used to establish the alleys, you must specify the number of keys per alley, as well
as the starting key number for each alley. A PDA file can contain a maximum of eight alleys.
Enter the file format information, as follows:
· In the Custom Comment box, type any desired text information to include in the PDA file
header.
· In the Number of Alleys box, type the number of alleys to include in the PDA file, or use the
arrow buttons to select the desired number. As you increase or decrease the number of alleys, the
available Alley Start Key boxes increase or decrease, as applicable.
· In the Alley # Start Key boxes, type the number of the first key for each alley, or use the arrow
buttons to select the key number.
NOTE: PDA files are exported with a *.pda extension.

4-3
SECTION FOUR

REPORTS TAB
Use the Reports tab to set up the available print area on a page for all reports and print screens output
to a printer. Enter the margin values in the left, right, top, and bottom text boxes.

RESTRICTIONS TAB
Use the Restrictions tab to disable various functions throughout the software. Once restrictions are set
up, a password is required in order to enable or disable the restrictions. You can restrict the following
functions:
· Select the Changing Options check box to disable all of the Options dialog box tabs except for
the Instruments tab. When this check box is selected, only the Instruments tab is displayed on
the Options dialog box.
· Select the Performing Job and Project Maintenance check box to disable all of the job
maintenance and project maintenance functions, including creating new projects and jobs. When
this check box is selected, the maintenance commands on the Job menu are unavailable.
· Select the Modifying Libraries check box to disable all Library Manager maintenance functions.
When this check box is selected, users can view and select library items, but cannot add, edit, or
delete library items.
· Select the Deleting Sheets check box to disable the delete function from the sheet options.
· Select the Setting up Jobs check box to disable all of the Job Setup functions. When this check
box is selected, users cannot access the Job Setup wizard functions.
After you select the items that you want to restrict, click Set Password to set up a password which will
allow you to enable and disable the restrictions. The password can consist of any combination of five
through fifteen characters. You can also use the Set Password function to change an existing
password. On the Change Password dialog box, you are prompted to enter and confirm your new
password. Once set, this password is required to enable and disable the restrictions.
To immediately enable the restrictions, select the Enable restrictions check box at the bottom of the
tab. If this check box is not selected, you must enable the restrictions by choosing Restrictions from
the Tools menu. When restrictions are enabled, a check mark appears next to the Restrictions
command; to disable restrictions, choose Restrictions and enter the correct password when prompted.

4-4
 SECTION FIVE

5. Using the ATD Libraries

Once you have installed your instrument and set up the software options, you need to prepare your
ATD libraries. Before you can begin measuring and evaluating press sheets, you must define the type
of presses and color bars that you want to use. You can also set up custom colors, tags, and shop
targets and tolerances.
ATD comes with pre-loaded libraries for:
· press types from different manufacturers.
· industry-standard color bars.
· commonly used standard colors.
· Job tags.
You can use the pre-loaded information, or you can set up custom configurations for all of your
libraries. You can perform all of the library management and maintenance functions by using the
commands on the Library menu.

USING THE LIBRARY MANAGER DIALOG BOXES

The Library Manager is a common type of dialog box that is used by four types of libraries (each
accessible through the commands on the Library menu): Color Bars, Presses, Targets, and Tolerances.
This type of dialog box allows you to edit, create, delete, duplicate, import, and export specific library
items.
While each Library Manager is specific to the type of information it supplies, you perform certain
functions in the same way for all types of library items. Common functions include:
· duplicating a library item.
· deleting a library item.
· setting a library item as a default.
· printing a report for a library item.
· importing a library item.
· exporting a library item.

Duplicating a Library Item

Use the Duplicate function to save data from an library item under a new name. This function is useful
if you want to create a new item based on an existing item.
NOTE: When you duplicate a target, the associated tolerance information is also duplicated, and vice
versa.
To duplicate an item:
1. Open the Library Manager that you want to use by choosing the appropriate command from the
Library menu.
2. From the Names list, select the item that you want to duplicate.
3. Click Duplicate to open the appropriate editor for this library item.
4. Type a new name for this library item. If necessary, you can also edit any of the other information.

5-1
SECTION FIVE

5. Click OK to save the new information.

Deleting a Library Item

When you delete a library item, you permanently remove that item from the library.
NOTE: If you delete a target, the associated tolerance is deleted, and vice versa.
To delete a library item:
1. Open the Library Manager that you want to use by choosing the appropriate command from the
Library menu.
2. From the Names list, select the item that you want to delete.
3. Click Delete. A confirmation message asks you to verify the deletion. Click Yes to complete the
deletion.

Setting a Default Library Item

If you use one particular library item frequently, you can identify that item as the default. For example,
if you use one type of press for a number of different jobs, you could set up that press as the default.
That press is then selected by default when you set up a job.
To set an item as a default:
1. Open the Library Manager that you want to use by choosing the appropriate command from the
Library menu.
2. From the Names list, select the item you want to use as a default.
3. Click Set Default.

Printing a Library Item Report

1. Open the Library Manager that you want to use by choosing the appropriate command from the
Library menu.
2. From the Names list, select the item you want to use to generate the report.
3. Click Report. You can then select your print options from the standard Windows Print dialog
box.

Importing a Library Item

Use the Import function to import a library from a different directory location.

To import an item:
1. Open the Library Manager that you want to use by choosing the appropriate command from the
Library menu.
2. Click Import to open the Import dialog box.
3. From the Look In list, select the drive or folder which contains the file you want to import.
4. The contents of the selected drive or folder appear in the folders list (only files of the appropriate
type are displayed.) To begin the import process, select the file you want to import, then click
Open.

Exporting a Library Item

Use the Export function to export a library item to a different directory location.

5-2
 USING THE ATD LIBRARI E S

To export an item:
1. Open the Library Manager that you want to use by choosing the appropriate command from the
Library menu.
2. From the Names list, select the item that you want to export.
3. Click Export to open the Export dialog box.
4. From the Save In list, select the drive or folder to which you want to export the file.
To export the file to a new folder, click the New Folder button. A new folder appears, and you can
type a name for the folder.
5. In the File name box, type a name for the file.
6. Click Save to export the item to the specified location.

THE PRESSES LIBRARY

To open the Presses Library Manager, choose Presses from the Library menu. Using the function
buttons, you can edit existing presses, create new presses, duplicate presses, import and export presses,
and delete presses.

Creating and Editing Presses

Use the Press Editor dialog box to create and edit presses. You define a press by its name, size, type,
and related attributes. This information is then used in the measurement calculations.
To create a new press or edit an existing press:
1. From the Library menu, choose Presses. The Presses Library Manager appears.
2. If you want to create a new press, click Create. The Press Editor dialog box appears
If you want to edit an existing press, select the press that you want to edit from the Names list,
then click Edit. The Press Editor dialog box appears.
3. In the Press Name box, type a name for this press. This name identifies this press on the Presses
Library Manager. The name is different from the Press Type, which refers to a manufacturer
brand name or generic name. The name allows you to differentiate between different presses of the
same type.
4. If necessary, type any comments about this press in the Comments box.
5. From the Press Type list, select the type of press you want to use. When you select a press type, a
diagram representing the type appears below the Press Type list, and the system automatically
updates the Press Size Information and Press Attributes based on the values of the selected
press type. If you want to customize your press settings, select the generic press type, rather than a
specific manufacturer press type.
6. If necessary, adjust the number of ink keys in the appropriate box under Press Size . The number
of keys must be between 1–99.
7. If necessary, adjust the size of the ink keys in the appropriate box under Press Size . The key size
must be between 6mm and 275mm (.235in.–10.2in.). Keys are incremented in .25 mm (.01 in.)
intervals.
8. Under Press Attributes, select the appropriate key order—progressing from first to last or from
last to first.
9. Click OK to save the press information.

5-3
SECTION FIVE

THE COLOR BARS LIBRARY

To open the Color Bar Library Manager, choose Color Bar from the Library menu. Using the
function buttons, you can edit existing color bars, create new color bars, duplicate existing color bars,
import and export color bars, and delete color bars.

Requirements for Creating Color Bars

Listed below are Repeat, Stripping, and Paper guidelines to help you create a color bar. These
guidelines ensure strip readability by the instrument.
Repeat Requirements
· You can use up to eight inks in a repeat.
· If the paper color is not white, you must include a paper patch in the repeat.
· Repeats can contain the following types of patches: solid ink, 25% tint, 50% tint, 75% tint, two -
color overprints, gray balance, paper, and “not used.”
· Repeats can be longer than the sheet length.
· The smallest measurable patch width is 3.8 mm, and smallest measurable patch height is 3.2 mm.
· A gap must be greater than a patch width, equal to a patch width, or less than half a patch width.
For a gap that is less than half a patch width, add the gap’s width to one of the two patches
adjacent to the gap. For example, if you have a 5 mm patch with a 1 mm gap, make one of the
patches adjacent to the gap 6 mm wide.
· The repeat cannot be symmetric in both directions.
· A patch cannot be wider than a key width.
· Patches of the same color can be adjacent.

Stripping Requirements
· Repeats must be constant in length.
· All repeats, except those at the beginning and end of the sheet, must be full repeats. A masked
repeat is considered a full repeat.
· Fractional repeats can only exist at the beginning or end of a sheet.
· Repeats can be masked only in a manner which does not increase the overall length of the repeat
(that is, pieces can be covered, but not moved).
· Only paper can reside within the masked region of a repeat.
· A single repeat can be masked into more than two pieces; however, the unmasked portion must
contain at least one unique patch.
· Extra non-paper information (patches not defined in the repeat or other marks on the paper) cannot
appear between repeats.
· Repeats can be forward, reversed, or both on the same sheet.
· No more than 1024 patches can exist in a single color bar.
· If there is no paper patch in the repeat, there must be paper somewhere in the scan area.
· The color bar can be stripped at a slight angle (with respect to sheet edge), as long as it is within
1.5 inches of the sheet edge for the entire length. It is recommended that any angle be kept to less
than 1° for maximum readability during the recognition process.

5-4
 USING THE ATD LIBRARI E S

· The color bar cannot be “bowed.” While it can be at a slight angle (as indicated above), it must be
in a straight line (the middle of the color bar cannot be higher or lower than both of the ends).
Paper Requirements
· Nominal paper size must remain constant throughout the run. Paper which is cut and re-measured
may have patch-to-key assignment differences.

Creating and Editing Color Bars

New color bars are based on a default repeat consisting of the four process ink colors in the sequence
of Black, Cyan, Magenta, and Yellow. If you specify more than four inks, these indicators are left
“blank” and are numbered from 5–8. (You can use up to eight inks.)
NOTE: The system always uses this default repeat for new color bars.
To create a color bar:
1. From the Library menu, choose Color Bar to open the Color Bar Library Manager.
2. Click Create. The Create Color Bar dialog box appears.
NOTE: To edit an exiting color bar, select the color bar you want to edit from the Names list, and
then click Edit. You can then edit the color bar information as explained in steps 6-10.
3. In the Number of Patches box, type the total number of patches in the color bar repeat, or use the
arrow buttons to select the number of patches.
4. In the Nominal Patch Width box, type the nominal patch width, or use the arrow buttons to select
the width. As the default, the system assigns this width to all of the patches on the new color bar
repeat.
5. Click OK to continue and open the Color Bar dialog box.
6. In the Name box, type a name for the new color bar. You can enter a name of up to 20 characters.
7. If necessary, type any comments about this color bar in the Comments box.
8. Under Color Bar, set up the color bar repeat (the basic color bar component that may be printed
several times, depending on the press sheet width). The system labels each patch icon according to
the patch type and ink color. You can add new patches, rearrange patches, and change patch
information, as follows:
· Use the Insert button to add new patches to the color bar.
· Use the Cut, Copy, and Paste buttons to rearrange the existing patches.
· Use the Edit Patch dialog box to define individual patches (such as changing the type of patch,
the percent tint, or the ink color).
9. If necessary, click Change Nominal Width to open the Change Nominal Width dialog box. You
can then enter a different width to use as the nominal patch width for the color bar.
10. When you are satisfied with the color bar information, click OK. The new color bar name appears
in the Names list of the Color Bar Library Manager.

Adding a Patch to a Color Bar

Use the Insert button on the Color Bar dialog box to add a new patch to the color bar repeat.
To add a patch:
1. Select the location on the color bar where you want to insert the new patch. The system inserts
patches to the left of the selected patch.

5-5
SECTION FIVE

2. Define the patch type and ink information on the Edit Patch dialog box (located below the Color
Bar dialog box).
3. On the Color Bar dialog box, click Insert to add the newly defined patch to the color bar.

Rearranging Patches on the Color Bar

Use the Cut, Copy, and Paste buttons on the Color Bar dialog box to rearrange the color bar repeat.
To move a patch from the current location and paste in a different location:
1. Select the patch you want to move.
2. Click Cut. The patch is removed from the color bar.
3. Select the location on the color bar where you want to insert the patch. The system pastes patches
to the left of the selected patch.
4. Click Paste. The cut patch is pasted to the left of the selected patch location.
To copy a patch to a second location on the color bar:
1. Select the patch you want to copy.
2. Click Copy.
3. Select the location on the color bar where you want to insert the copied patch.
4. Click Paste. The copied patch is pasted to the left of the selected patch location.

Defining Individual Patches (Color Bars)

Use the Edit Patch dialog box to define individual patches on a library color bar. On the Color Bar
dialog box, select the patch in the color bar repeat that you want to modify. If you are inserting a new
patch, select the patch to the right of the location where you want to insert the patch. You can select a
patch by clicking it with your mouse, or by using the arrow buttons below the color bar display to
move forward and backward through the patches.
To define a patch:
1. Under Patch Types, the system displays buttons for each possible patch type (Solid, Overprint,
Gray Balance, 75% Tint, 50% Tint, 25% Tint, Not Used, or Paper). Click the button for the type
of patch you want to define.
2. Under Inks, the system displays individual ink indicators for all of the inks used on the color bar.
Select the ink or inks to use on the patch by clicking the appropriate ink indicators in the proper
sequence.
NOTE: If necessary, you can define new ink colors by selecting different colors from one of the
color libraries.
3. After you define the patch type, the current information (including the patch type and inks used)
appears under Current Patch Settings. If necessary, edit the patch identification in the ID box.
4. If necessary, edit the patch width in the Size box, or use the up and down arrows to adjust the
patch size.
5. If you are using a Tint patch, you can edit the screen percentage in the Screen box—either type in
a new screen percentage or use the arrow buttons to adjust the screen percentage.
6. Your patch setup is now complete. If you were editing an existing patch, re-select that patch on the
Color Bar dialog box to update the patch information. If you were defining a new patch, click
Insert on the Color Bar dialog box to add the patch to the color bar.

5-6
 USING THE ATD LIBRARI E S

THE COLORS LIBRARY

The ATD software uses three different types of color libraries:
· The User Color library allows you to add custom colors to ATD and group together commonly
used colors for easy access. You can add new colors to the User Color Library by importing c olors
from other ATD libraries, by manually defining a new color, or by measuring in a color with your
handheld instrument.
· The Standard Color library includes 16 commonly used colors (selected and defined by X-Rite,
Inc.).
· The Scanned Color library allows you to use your scanning instrument to create a color library.
To access these libraries, choose Color from the Library menu. This opens the Select Color dialog
box, where you can add colors to the User Color library and the Scanned Color library, rename and
remove colors from the User Color library, and search for a specific color name.
You can also use the Select Color dialog box to define ink colors (for ink indicators used on presses,
color bars, targets, and spot measurements).

Adding Colors from Other Libraries to the User Color Library

1. From the Library menu, choose Colors to open the Select Color dialog box.
2. From the Library list, select the color library which contains the color you want to add to the User
Color library. All of the colors in the selected library appear in the list area.
3. From the list area, select the specific color that you want to add to the User Color library.
4. Click Library Management to open the shortcut menu. Choose Add to User Library. The
Enter Text dialog box appears.
5. In the Name box, type a name for the color.
6. Click OK to add the selected color to the User Color library.

Adding Colors to the Scanned Color library

You can use your scanning instrument to add new colors to the Colors library. The Scanned Color
library includes colors recognized by the scanning instrument. Each color in the library is assigned
"Ink Color #" as the color name, where # is the sequence number of the color (for example, the third
color on a color bar is named Ink Color 3).

To scan colors for the Scanned Color library.

1. Place the color bar that you want to scan on the track of the scanning instrument.
2. From the Library menu, choose Colors to open the Select Color dialog box.
3. From the Library list, select Scanned Color Library. The library can only include colors from a
single scan (you cannot add colors from several different scans to the library). If there are no
existing colors in the library, the instrument will automatically start to scan the color bar.
If the library already contains colors, you have to manually initiate the scan. Click Library
Management, then choose Re-scan to start the measurement. The new colors identified from the
scan will overwrite any existing colors in the Scanned Color library.

Renaming Colors in the User Color Library

If necessary, you can rename a color in the User Color library.
NOTE: If you rename a color, you will not affect existing Jobs which use the color.

5-7
SECTION FIVE

To rename a color:
1. From the Library menu, choose Colors to open the Select Color dialog box.
2. From the Library list, select User Color Library.
3. All colors in the User Color library appear in the list area. Select the color that you want to
rename.
4. Click Library Management to open the shortcut menu. Choose Rename, and the Enter Text
dialog box appears.
5. In the Name box, type a new name for the selected color.
6. Click OK to rename the selected color.

Removing Colors from the User Color Library

If necessary, you can remove unwanted colors from the User Color library. However, once you remove
a color, you cannot retrieve the color again.
NOTE: If you remove a color, you will not affect existing Jobs which use the removed color.
To remove a color:
1. From the Library menu, choose Colors to open the Select Color dialog box.
2. From the Library list, select User Color Library.
3. All of colors in the User Color library appear in the list area. Select the color that you want to
remove.
4. Click Library Management to open the shortcut menu. Choose Remove to delete the selected
color.

Importing Colors into the User Color Library

You can import color files with a *.clr extension into the User Color library.
To import colors:
1. From the Library menu, choose Colors to open the Select Color dialog box.
2. From the Library list, select User Color Library.
3. Click Library Management to open the shortcut menu. Choose Import. The Import Color
dialog box appears.
4. From the Save In list, select the drive or folder that contains the color file you want to import.
5. The contents of the selected drive or folder appear in the folders list (only color files are
displayed). To begin the import process, double-click the appropriate file, or select the file and
click Open.

Searching for a Color Name

The Search for Color function allows you to search the User Color library for a specific color name.

To search for a color:

1. From the Library menu, choose Colors to open the Select Color dialog box.
2. From the Library list, select the User Color Library.
3. Click Library Management to open the shortcut menu. Choose Search for Color, and the Find
Color dialog box appears.
4. In the text box, type the color name you want to find. Click OK to begin the search.

5-8
 USING THE ATD LIBRARI E S

5. The system searches the current color library for the color name. If it finds a matching color, it
automatically selects the color. If no matching color is found, the system displays the message
“No match found.”

Selecting Ink Colors

Throughout the software, you can use ink indicators to define the inks used in presses, color bars, and
spot measurements, as well as the associated targets and tolerances.
The ink indicators represent the actual ink color used in a specific key, color bar, or spot measurement
location. Wherever ink indicators appear, you can use the Select Color dialog box to determine the
color of the actual ink.

To select an ink color from the Select Color dialog box:

1. Double-click in the ink indicator position you want to edit. The Select Color dialog box appears.
(Where applicable, you can also click the Select Color button to open the dialog box.)
NOTE: You select ink colors by using a drag-and-drop function, so you cannot select colors if the
dialog box overlaps the indicators. If the dialog boxes overlap, move the Select Color dialog box
by clicking the title bar, holding down the left mouse button, and dragging the dialog box to the
new location.
2. From the Library list on the Select Color dialog box, select the color library which contains the
color you want to use.
3. All available colors appear in the list area. Select the color you want to use, hold down the left
mouse button, and drag the color to the appropriate ink indicator position.
4. When the paint brush icon appears over the ink indicator, release the mouse button. The system
"drops" the color onto the selected ink indicator.

THE TAGS LIBRARY

Tags help you identify jobs or sheets and allow you to associate jobs or sheets with a specific group.
You can perform tag management through the Tags dialog box, which allows you to add, modify, and
delete tags and user tag groups. From the Library menu, choose Tags to open the Tags dialog box.
The Tags dialog box organizes tags by category and group. There are two categories of tags, as
follows:
· Job Tags consist of several predefined groups that are used on Identification dialog box in the Job
Setup wizard. These groups are provided with the system—you cannot add new Job Tag groups or
remove existing Job Tag groups. Within these groups, however, you can add, modify, or delete
individual tags.
· User Tags consist of groups and tags defined by the user. You can assign these tags to individual
sheets within a job, and then use these tags to filter specific sheets for analysis when using the
Statistical Process Control software. You can add, modify, and delete User Tags and User Tag
groups.
There are three different types of tags available:
· Normal tags are User Tags that you can only assign to the current sheet. Normal tags are not
stored in groups.
· Floating tags are User Tags that, once assigned to a specific sheet, are automatically assigned to all
following sheets. You can discontinue the Floating tag by manually removing it from the last sheet
scanned. Floating tags are not stored in groups.
· Group tags are the only type of tags which can be stored in groups. All Job tags are group tags.
Only one tag within a group can be assigned to a specific sheet. For example, if you create a

5-9
SECTION FIVE

“Shift” group which contains the tags “Shift 1”, “Shift 2”, and “Shift 3”, only one of the shift tags
can be assigned to any specific sheet. Like Floating tags, Group tags are assigned to all following
sheets until manually removed.
Use the following guidelines when you create and edit tags:
· You cannot modify or delete Job Tag or User Tag category names.
· You cannot modify or delete Job Tag group names.
· You can only modify or delete a user-defined group name if the group does not contain individual
group tags.
· Any newly created group appears under the User Tags category.
· A tag name can be up to 25 characters long.
· You can only assign Job tags during Job Setup (on the Job Setup - Identification dialog box). To
assign sheet tags, click the Tags button on the Control pane. The Add or Remove Tags dialog
box appears, and you can change the tag assignments of the current sheet.

Creating and Editing Tags

1. From the Library menu, choose Tags to open the Tags dialog box.
2. Click Add to open the New Tag dialog box.
NOTE: To edit an existing tag, select the tag that you want to edit from the list area, then click
Modify. You can then edit any of the tag information using the steps below.
3. In the Tag Name box, type the tag name.
4. Identify what type of tag you want to create by selecting the appropriate option: Normal ,
Floating, or Group.
5. If this is a Group tag, you must identify the group to use for the tag. From the Select Group list,
select the group that you want to use.
6. Click OK.

Creating and Editing User Tag Groups

1. From the Library menu, choose Tags to open the Tags dialog box.
2. Click Add to open the New Tag dialog box.
NOTE: To edit an existing User Tag group, select the group that you want to edit from the list
area, then click Modify. You can then edit any of the tag information using the steps below.
3. Select the Group Name check box to indicate that this is a User Tag group.
4. In the Tag Name box, type the name for this group.
5. Click OK.

Deleting a Tag or User Tag Group

NOTE: Deleting a tag does not affect previous jobs or sheets which use the selected tag.
1. From the Library menu, choose Tags to open the Tags dialog box.
2. From the list area, select the tag or User Tag group that you want to delete.
3. Click Delete. A confirmation message asks you to verify the deletion. Click Yes to confirm the
deletion.
NOTE: You cannot delete groups that already contain tags.

5-10
 USING THE ATD LIBRARI E S

Add or Remove Tags dialog box

Use the Add or Remove Tags dialog box to attach a User Tag to the current sheet. To open the dialog
box, click the Tags button on the Control Pane (you can also open the dialog box by choosing Tags
from the Sheet submenu on the Tools menu).
To add or remove tags from the current sheet:
1. All available tags that are not currently assigned to the sheet appear in the Available Tags list. To
assign a tag to the current sheet, select the tag in the Available Tags list, then click Add to move
the tag to the Current Tags list.
2. All tags that are assigned to the sheet appear in the Current Tags list. To remove a tag from the
current sheet, select the tag in the Current Tags list, then click Remove to return the tag to the
Available Tags list.
3. Click OK to assign the selected tags to the current sheet.

THE TARGET AND TOLERANCE LIBRARIES

Target and Tolerance libraries allow you to store frequently used ink data (values and tolerances) for
specific patches on a color bar. When you set up a new job, you can use this data for the job’s patch
targets and tolerances.
You create and edit target and tolerance data through the Target and Tolerance Library Managers.
While these appear as two separate commands on the Library menu, you can create and edit both
items from either Library Manager. The targets and tolerances correspond on a one-to-one basis; for
each target that you create, the system automatically creates the associated tolerance (and, likewise, for
each tolerance that you create, the system automatically creates the associated target). The system
provides default tolerance values, so you can create a target without necessarily editing the tolerance
information. However, if you create a tolerance, you must define the target values.
The system identifies targets and tolerances by the ink names used (e.g., Cyan, Cyan/Magenta/Yellow,
etc.). During Job Setup, you can choose to use targets and tolerance values from the libraries as the
target and tolerance values for the job. The system selects values by matching ink names in the Target
and Tolerance libraries with ink names defined in the job. If an match is found, the system copies those
values to the job.

Creating and Editing Shop Targets

1. From the Library menu, choose Target to open the Target Library Manager.
2. Click Create to open the Create Library Entry dialog box, where you define the type of patch
for which you want to create targets. Select the patch type you want to use: Ink, Overprint, Gray
Balance, or Spot Measurement.
NOTE: To edit an existing target, select the target that you want to edit from the Names list on
the Target Library Manager, and then click Edit. You can edit any of the target information
using the steps below.
3. Click OK to open the Target tab on the Shop Target and Tolerance dialog box.
4. Once the Target tab is displayed, you can define the target values. As a default, only the Density
target value is activated. If you want to define all possible target values, select the Let me change
all targets check box to enable all target values applicable to the patch type. You can then either
automatically generate the target values or manually define the target values, as follows:
· To automatically generate target values, you can either measure colors or select colors from
one of the color libraries. You must repeat the measurement or selection process for each ink
required for this patch type (Ink and Spot Measurement patch types require one ink; Overprint
patch types require two inks; and Gray Balance patch types require three inks). The target
values are then automatically generated based on the measured or selected ink colors.

5-11
SECTION FIVE

· To manually enter target values, type the target value in each target box. The actual target
types available depends on the patch type for which you are creating a target.
5. Type or edit the ink names in each required Ink # box. The number of inks required depends on
the patch type for which you are creating the target.
The target (and associated tolerance) is identified by the names of the inks used for this specific
patch. For example, if you create a target for a Gray Balance patch type and enter ink names of
Cyan, Magenta, and Yellow, that target is identified as Cyan/Magenta/Yellow. If you
automatically generated target values by selecting ink colors from the color libraries, the library
names of the selected inks are used by default. You can edit these names, if necessary.
6. Select a filter to apply to this target. If you automatically generated target values, the system
selects the appropriate filter for use with this target. However, you can select a different filter, if
necessary, from the Filters list (you can select from Visual, Cyan, Magenta, or Yellow filters).
7. For Ink and Spot Measurement patch types only, select the Add this Color to User Color
Library check box if you want to use these target values to define a new color in the User Color
Library. The color is saved in the User Color Library by the ink name.
8. When you are satisfied with your target settings, you can either select the Tolerance tab and
adjust the tolerance settings, or you can click OK to save the target information and return to the
Target Library Manager.

Creating and Editing Shop Tolerances

NOTE: When you create a tolerance, you must also be sure to set the associated target values.
1. From the Library menu, choose Tolerance to open the Tolerance Library Manager.
2. Click Create to open the Create Library Entry dialog box, where you define the type of patch
for which you want to create tolerances. Select the patch type you want to use: Ink, Overprint,
Gray Balance, or Spot Measurement.
NOTE: To edit an existing tolerance, select the tolerance that you want to edit from the Names
list on the Tolerance Library Manager, and then click Edit. You can edit any of the tolerance
information using the steps below.
3. Click OK to open the Tolerance tab on the Shop Target and Tolerance dialog box.
4. Type the ink names in each required Ink # box. The number of ink names required depends on the
patch type for which you are creating the tolerance: Ink and Spot Measurement patch types require
one ink; Overprint patch types require two inks; and Gray Balance patch types require three inks.
The tolerance (and associated target) is identified by the names of the inks used for this specific
patch. For example, if you create a tolerance for a Gray Balance patch type and enter ink names of
Cyan, Magenta, and Yellow, that tolerance is identified as Cyan/Magenta/Yellow.
5. The ATD software allows you to define the tolerance settings for three different tolerance widths.
Select the width that you want to edit from the options at the bottom right corner of the dialog box:
Narrow, Medium, or Wide.
6. As a default, only the Density box is activated. If you want to define all possible tolerance values,
select the Let me change all tolerances check box (located at the bottom right corner) to enable
all tolerance values applicable for the patch type. You can further refine which tolerances are used
by selecting or clearing the appropriate check boxes to enable or disable the corresponding
tolerance type.
7. The system automatically generates tolerance values based on the tolerance width selected. Two
values are required for each type of tolerance; the first value represents the Action limit, and the
second value represents the Control limit. You can edit any of the default values.

5-12
 USING THE ATD LIBRARI E S

To edit the tolerance values, type the new tolerance value in each appropriate tolerance box. Only
those tolerance types appropriate for the current patch type will be available for editing.
Remember that you must manually enable the available tolerance types by selecting the
appropriate check box.
8. If you want to edit the tolerance values for more than one tolerance width, repeat steps 6–7 for
each tolerance width.
9. Once you are satisfied with your tolerance settings, you can either select the Target tab and define
the associated target values, or click OK to save the changes and return to the Tolerance Library
Manager.

5-13
SECTION FIVE

5-14
 SECTION SIX

6. Working with Project and Jobs

Each press run that you measure and evaluate is organized within the software as an individual job. A
job consists of a specific and unique press, sheet setup, color bar setup, and target/tolerance setup. To
help keep your jobs organized, you create projects. A project is a collection of individual jobs.
For example, you may be printing a catalog for one of your customers. If the same press, sheet size,
color bar, and related settings are used to print the entire catalog, you can use one job for the entire
project. However, if any of these settings are different for parts of the catalog, you can create separate
jobs within one project.
By maintaining job and project information, you can easily re-print jobs using the same settings and
parameters, and you can use existing job information to create new jobs.
When you first start up the Software, there are no jobs saved in your database. The first time you start
the software, the Select Job dialog box appears. This dialog box provides you with four options:
Create a New Job, Open an Existing Job, Import Job, and Exit Application. You can also access
these and other job and project maintenance functions from the Job menu.
NOTE: Many of the dialogs used for job and project maintenance functions feature a Refresh button.
When you click this button, the Software re-reads all the projects and jobs in the current directory. If
you have rearranged or moved files, click Refresh to update the directory contents

CREATING PROJECTS
1. From the Job menu, choose Project Maintenance, then choose Create. The Project Create
dialog box appears.
2. In the Project box, type your new project name.
3. The project is stored in the Current Directory. If you want to save the project to a different
location, click the Browse button (…). You can then select a different folder location from the
Select Directory dialog box.
4. Click OK to save the new project.

DELETING PROJECTS
When you delete a project, all of the jobs associated with that project are also deleted from the
database. Remember, ATD cannot recover deleted projects or jobs.

To delete a project:
1. From the Job menu, choose Project Maintenance, then choose Delete. The Project Delete dialog
box appears.
2. From the Project list, select the project that you want to delete. All jobs associated with the
selected project appear in the Job list. You can review this list to make sure that you want to
delete this project.
NOTE: The system only lists projects from the Current Directory location. If you want to delete
a project that is stored in a different directory location, click the Browse button (…). You can then
select a different folder location from the Select Directory dialog box.
3. Click OK. A confirmation message asks if you want to delete the selected project. Click Yes to
delete the project (and all associated jobs), or click No to cancel the procedure.

6-1
SECTION SIX

RENAMING PROJECTS
1. From the Job menu, choose Project Maintenance, then choose Rename. The Project Rename
dialog appears.
2. From the Existing Project to be Renamed list, select the project that you want to rename.
NOTE: The system only lists projects from the Current Directory location. If you want to
rename a project that is stored in a different directory location, click the Browse button ( …). You
can then select a different folder location from the Select Directory dialog box.
3. In the Project’s New Name box, type the new name for the project.
4. Click OK.

CREATING A NEW JOB

When you need to define a new press run, you must create a new job. You may also need to create a
project within which to group the new job.
To create a new Project and Job:
1. From the Job menu, choose New. The Job New dialog box appears. (You can also open this
dialog box by clicking Create a New Job on the Select Job dialog box)
2. If you want to create the job in an existing project, select the project that you want to use from the
Project list. If you want to create a new project, type a new project name in the Project box.
3. In Job box, type a name for the job.
4. The job will be saved in the directory shown in the Current Directory field. If you want to save
the job to a different location, click the Browse button (…). You can then select a different folder
location from the Select Directory dialog box.
5. Click OK to save the job information and automatically start the Job Setup wizard for the job.
You can also use the based-on function to create a new job based on an existing job.

CREATING A JOB BASED ON AN EXISTING JOB

At the bottom of the Job New dialog box, you can click the Based On check box to activate the Based
Job Directory. This feature allows you to use the parameters of an existing job as the basis for your
new job.
To create a new job based on an existing job:
1. From the Job menu, choose New. The Job New dialog box appears. (You can also open this
dialog box by clicking Create a New Job on the Select Job dialog box)
2. If you want to create the job in an existing project, select the project that you want to use from the
Project list. If you want to create a new project, type a new project name in the Project box.
3. In Job box, type a name for the job.
4. The job will be saved in the directory shown in the Current Directory field. If you want to save
the job to a different location, click the Browse button (…). You can then select a different folder
location from the Select Directory dialog box.
5. Select the Based On check box.
6. From the Project list, select the project that you want to use.
NOTE: The system only lists projects from the Based Job Directory location. If you want to
select a project that is stored in a different directory location, click the Browse button (…). You
can then select a different folder location from the Select Directory dialog box.

6-2
 WORKING WITH PROJECTS AND JOBS

7. From the Job list, select the job that you want to use as the basis for your new job.
8. Click OK to save the new job.
Your new job automatically uses the settings from the based-on job that you selected.

OPENING EXISTING JOBS

1. From the Job menu, choose Open. The Job Open dialog box appears. (You can also open this
dialog box by clicking Open an Existing Job on the Select Job dialog box).
2. From the Project list, select the project that contains the job you want to open.
NOTE: The system only lists projects from the Current Directory location. If you want to use a
project that is stored in a different directory location, click the Browse button (…). You can then
select a different folder location from the Select Directory dialog box.
3. From the Job list, select the job that you want to open.
4. Click OK to open the selected job.

COPYING JOBS
Use the Copy function to copy the active job.
1. From the Job menu, choose Job Maintenance, then choose Copy. The Job Copy dialog box
appears. The current project and job information appear at the top of the dialog box.
2. If you want to copy the job to an existing project, select the project that you want to use from the
Project list. If you want to copy the job to a new project, type a new project name in the Project
box.
NOTE: The system only lists projects from the Current Directory location. If you want to use a
project that is stored in a different directory location, click the Browse button (…). You can then
select a different folder location from the Select Directory dialog box.
3. In the Job box, type a new name for the job. If you want to overwrite an existing job with the
copied job, select the job that you want to overwrite from the Job list.
4. Click OK to complete the copy procedure. If you are overwriting an existing job, a confirmation
message will appear. Click Yes to verify the copy procedure.

DELETING JOBS
Use the Delete function to delete the current job. Remember, ATD cannot recover deleted jobs.
1. From the Job menu, choose Job Maintenance, then choose Delete.
2. A confirmation message asks you to verify the deletion. Click Yes to delete or No to cancel.
3. After the deletion is complete, the Select Job dialog box will appear. You can then create a new
job, open an existing job, or import a job.

MOVING JOBS
Use the Move function to move the current job to a different project.

To move a job:
1. From the Job menu, choose Job Maintenance, then choose Move. The Job Move dialog appears.
The current project and job information appear at the top of the dialog box.

6-3
SECTION SIX

2. If you want to move the job to an existing project, select the project that you want to use from the
Project list. If you want to move the job to a new project, type a new project name in the Project
box.
NOTE: The system only lists projects from the Current Directory location. If you want to use a
project that is stored in a different directory location, click the Browse button (…). You can then
select a different folder location from the Select Directory dialog box.
3. In the Job box, type a name for the job. If you want to overwrite an existing, select the job that
you want to overwrite from the Job list.
4. Click OK to complete the move procedure. If you are overwriting an existing job, a confirmation
message will appear. Click Yes to verify the move procedure.

RENAMING JOBS
Use the Rename function to rename the current job.

To rename the currently active job:

1. From the Job menu, choose Job Maintenance, then choose Rename. The Rename Job dialog
appears.
2. In the Job Name box, type a new name for the job.
3. Click OK.

IMPORTING JOBS
Use the Import function to import jobs from other ATD systems, or to retrieve jobs that you exported
to a different directory location.
To import a job:
1. From the Job menu, choose Import. The Import Job dialog box appears. (You can also open this
dialog box by clicking Import Job on the Select Job dialog box).
2. From the Look in list, select the drive or folder which contains the job you want to import.
3. The contents of the selected drive or folder appear in the list area (only files of the appropriate
type are displayed). To begin the import process, select the file that you want to import, then click
Open.
The imported job becomes the current job in the application. You can view job data and edit the job
information as you would any other existing job.

EXPORTING JOBS
Use the Export function to save jobs to a different directory location. Exported data can then be
restored to the database using the Import function.
To export a job:
1. The current job will be exported. Make sure you have the correct job selected before continuing.
2. From the Job menu, choose Export. The Export Job dialog box appears.
3. From the Save in list, select the drive or folder to which you want to export the job.
4. In the File Name box, type a name to use for the exported job (the current job name is used by
default).
5. Click Save.

6-4
 WORKING WITH PROJECTS AND JOBS

SENDING JOBS VIA E-MAIL

The Send function allows you to send a job via e-mail if MAPI e-mail support is present. The job file
is sent as an e-mail attachment through the resident mail host.
To send a job via e-mail:
1. The current job will be sent. Make sure you have the correct job selected before continuing.
2. From the Job menu, choose Send. The system first backs up the current job to a temp file.
3. After backing up the file, the ATD system automatically creates a new e-mail message with the
current job file included as an attachment. You can enter in the appropriate a-mail address and
message information.
Refer to your e-mail application documentation for additional information.

CREATING JOB EXTRACT FILES

You can extract job data in four different formats:
· X-Tract. This file format provides job information helpful in pre-press operations. The X-Tract
file is used to prepare a color profile of a press. This helps in the creation of film separations
which match the press. The X-Tract file is broken down into three different parts: the File Header,
the Density Table, and the Spectral Table. The File Header identifies the job and provides other
information relevant to the density and spectral data in the file. The Density Table provides
densitometric information about the attributes used in the job. The Spectral Table provides
reflectance information about the attributes used in the job.
· Scan Density File (SDF). This format provides densitometric information about the current job.
The SDF is broken down into two parts: the File Header and the Density Table. The File Header
identifies the job and provides other information relevant to the density data in the file. The
Density Table provides densitometric information about each patch on the color bar.
· Print Data Analysis (PDA). This format allows you to exchange press densitometric data
between "on-board" scanning systems and a print data analysis (PDA) program. The Print Data
Exchange File Format function generates the file format-a cross platform, device-independent file
specification-used for this data exchange. You set up the parameters for this type of file on the File
Formats tab of the Options dialog box.
To create a job extract file:
1. The current job will be extracted. Make sure you have the correct job selected before continuing.
2. From the Job menu, choose Extract Files, then choose the specific type of file that you want to
create. The Extract File dialog box appears.
2. From the Save in list, select the drive or folder to which you want to extract the current job.
3. In the File name box, type the file name you want to use for the job data.
4. Make sure that the proper file type is selected in the Save as type list.
4. Click Save to extract the current job into the selected format.

JOB STATUS DIALOG BOX

This dialog box allows you to quickly evaluate how your job is performing, sheet-by-sheet. To open
the dialog box, click the Status button on the Control pane (you can also open the dialog box by
choosing Status from the Sheet submenu on the Tools menu). The dialog box lists any Action Limit or
Control Limit failures on the current sheet. The system identifies each limit failure by the ink name,
patch type, and associated key numbers.

6-5
SECTION SIX

6-6
 SECTION SEVEN

7. Setting Up Your Job

A job consists of press, sheet, color bar, ink, and target and tolerance information. You use the Job
Setup wizard to define these parameters for a new job, or to edit the parameters for an existing job. The
wizard walks you through all of the steps necessary to set up your job.
To set up your Job:
1. Start the Job Setup wizard. When you create a new Job, the system automatically starts the Job
Setup wizard for the job. You can manually start the wizard by choosing Setup from the Job
menu.
NOTE: If you are working on a master workstation and this function is unavailable, it may be
restricted. If you know the correct password, you can check the settings on the Restrictions tab of
the Options dialog box.
2. On the Job Setup - Press dialog box, select the press and inks that you want to use on the Job.
Click Next to continue.
3. On the Job Setup - Color Bars dialog box, assign a color bar to each sheet edge that you are
using on the Job. Click Next to continue.
4. On the Job Setup - Summary dialog box, you can access additional dialog boxes where you can
define the targets and tolerances for the Job and enter identifying information for the Job.
5. When you complete the setup process, click Finish to complete the setup process wi thout
recognizing the Job, or click Finish and Recognize to automatically start the Recognition wizard
for this Job.
NOTE: If you are editing an existing Job, the software will prompt you to either overwrite the existing
Job data with the new data, or to save the new data under a new Job name. On the Job Changed dialog
box, click Overwrite if you want to overwrite the current Job with the new data (all existing sheets
will be deleted when you overwrite the Job); click Save As to save the new data as a new Job.
After you complete the Job Setup wizard, you can use the Job Properties dialog box to review the job
data.

PRESS DIALOG BOX

Use the Job Setup - Press dialog box to select the specific press that you want to use, select or
measure the inks used on the press, and define sheet information.

To set up the press information:

1. Click Select Press to open the Select from Library dialog box, where you can select the press
that you want to use on the job. From the Names list, select the press that you want to use, then
click Select. The name of the selected press appears in the Press box, and a diagram of the
selected press appears below the Press box.
2. To turn specific press keys on or off, click Manage Keys. The Manage Keys dialog box appears,
and you can enable or disable specific keys on the selected press.
3. Using the ink indicators on the press diagram, select the inks that you want to use on the press.
You select the inks from one of the color libraries.
NOTE: To remove an ink from the press, select the ink indicator that you want to remove, then
click Remove Ink. You can also remove an ink by dragging it off the Press diagram and dropping
it onto the Trash Can icon.
4. Under Sheet Information, define the sheet that you are using on the job:

7-1
SECTION SEVEN

· In the Width box, type the width of the sheet that you are using for this job, or use the arrow
buttons to select the appropriate width.
· The Color swatch represents the sheet color. If you want to define a different color for your
sheet, you can select a color from one of the color libraries.
· Define the location of the sheet on the press. If you center your sheet on the press, select
Centered. If you do not center the sheet, select Left edge on key. If you select this option,
you must also enter the key number corresponding to the left edge of the sheet. Type the key
number in the appropriate box, or use the arrow buttons to select the key number.
5. When you are satisfied with your press settings, click Next to continue to the next step in the
wizard: Job Setup - Color Bars.

Manage Keys dialog box

Use the Manage Keys dialog box to enable or disable specific keys on the current press. To open the
dialog box, click Manage Keys on the Press dialog box of the Job Setup wizard, or choose Manage
Keys from the Keys submenu on the Tools menu.
To turn keys on and off:
1. All of the inks used on the press appear as individual options on the right side of the dialog box.
To turn keys on or off for a specific ink, select the option button for the ink that you want to use.
To turn keys on or off for all inks, select the Press (all inks) option.
2. All of the keys on the current press appear in the Key Status list. To turn a specific key on, select
the check box for that key; to turn a key off, clear the check box for that key.
3. When you finish making your key selections, click OK to save the settings and close the dialog
box.

COLOR BARS DIALOG BOX

At this step in the Job Setup wizard, you must select the color bars that you want to use on the job.
To set up color bars:
1. The sheet edges (Gripper/Front, Trailing/Front, Trailing/Back, Gripper/Back) are represented with
location tabs at the top of the dialog box. The default color bar is automatically assigned to the
first tab location. Use the Add, Delete, Change, and Location buttons to add color bars to a sheet
edge, remove color bars, change color bars, and move color bars to a different location. You can
assign up to eight different color bars to each sheet edge.
2. Use the check boxes below the location tabs to further define individual color bars:
· Select the Flopped on sheet check box if the current color bar repeat (the color bar selected
on the current location tab) is reversed on your sheet.
· Select the Off during makeready check box if the current color bar is not used during the
makeready phase.
3. When you finish setting up all of the color bar information, click Next to continue to the next step:
Job Setup - Summary.

Adding Color Bars to a Sheet Edge

1. On the Job Setup - Color Bars dialog box, select the location tab to which you want to add a
color bar. For example, if you want to add a color bar to the Gripper/Front edge, select the
Gripper/Front tab.
2. Click Add. The Select From Library dialog box appears.

7-2
 SETTING UP YOUR JOB

3. From the Names list, select the color bar you want to use.
4. Click Select. The system adds the color bar to the current location.

Removing Color Bars from a Sheet Edge

1. On the Job Setup - Color Bars dialog box, select the location tab which contains the color bar
you want to remove. For example, if you want to remove a color bar from the Gripper/Front edge,
select the Gripper/Front tab.
2. All of the color bars assigned to the current location appear in the list area below the tab. Select
the color bar that you want to remove.
3. Click Delete.

Changing Color Bars on a Sheet Edge

1. On the Job Setup - Color Bars dialog box, select the location tab which contains the color bar
you want to change. For example, if you want to change a color bar on the Gripper/Front edge,
select the Gripper/Front tab.
2. All of the color bars assigned to the current location appear in the list area below the tab. Select
the color bar that you want to change.
3. Click Change. The Select From Library dialog box appears.
4. From the Names list, select the color bar that you want to use.
5. Click Select. The new color bar replaces the previous color bar on the current location.

Moving a Color Bar to a Different Sheet Edge

1. On the Job Setup - Color Bars dialog box, select the appropriate location tab based on the sheet
edge you want to use. For example, if you want to move a color bar that is currently located on the
Gripper/Front edge, select the Gripper/Front tab.
2. All of the color bars assigned to the current location appear in the list area below the tab. Select
the color bar that you want to move.
3. Click Move. The Colorbar Location dialog box appears.
4. Under New Location, select the location to which you want to move the color bar.
5. Click OK. The system removes the color bar from the previous location and moves it to the newly
selected location.

SUMMARY DIALOG BOX

The Job Setup - Summary dialog box displays a summary of the ink target values and provides
access to advanced job setup functions: Targets and Tolerances and Identification.
To finalize your job setup:
1. Define the targets and tolerances to use for the job. Click Targets and Tolerances to open the
Job Setup - Targets and Tolerances dialog box, where you can set up specific target and
tolerance values for the job.
2. Enter the necessary data to identify the job. Click Identification to open the Job Setup -
Identification dialog box, where you can enter job-specific information and assign Job tags.
4. When you have set up all of the advanced job functions, you can click Finish to save the job data
without proceeding to the Recognition wizard, or you can click Finish and Recognize to
automatically advance to the Recognition wizard.

7-3
SECTION SEVEN

TARGETS AND TOLERANCES DIALOG BOX

The Job Setup - Targets and Tolerances dialog box is organized into several different areas. Use the
different options to either manually define target and tolerance values or use values from the Target
and Tolerance libraries; to determine the tolerance width used on the job, to select the types of
tolerances to use on the job, and to set up tolerance factors.
To set up the target and tolerance information:
1. Determine how you want to define target and tolerance values:
· If you want to manually define the target and tolerance values for a specific patch type, use
the buttons under Set Targets and Tolerances for.
· If you want to values from the Target and Tolerance libraries as the target and tolerance
values for the job, use the buttons under Reset values to. Click Shop Targets to reset all job
targets to the values from corresponding targets in the Target library; click Shop Tolerances
to reset all job tolerances to the values from corresponding tolerances in the Tolerance library.
The library target and tolerance values are only used if an ink or ink combination used in the
job matches up identically to the name of a target or tolerance library item.
2. Select the tolerance width that you want to use as the basis for evaluating measurement data.
Under Tolerance width, select the width for the job: Narrow, Medium, or Wide.
3 Determine what types of tolerances you want to use for the job:
· If you only want the system to use Density target and tolerance information during the
makeready phase, select the Only watch only density during makeready check box.
· If you want to enable all tolerances (or enable specific types of tolerances) during the
makeready phase, click Enable all Tolerances. This opens the Enable all Computations
dialog box, where you can enable or disable specific tolerance types for each patch type.
4. If necessary, edit the tolerance factors. These factors are used to generate default values for
medium and wide tolerances. For example, if the medium tolerance factor is set at 2.0, then the
medium tolerance values will be twice the narrow tolerance values. If a narrow tolerance Action
limit is set at 2.0, and the medium tolerance factor is set at 2.0, then the corresponding medium
tolerance Action limit = 4.0. To change the tolerance factors, click Set Factors. This opens the Set
Factors dialog box. Enter the medium and wide factors in the appropriate fields, then click OK to
set the new factors.
5. When you finish setting up the target and tolerance information, you can either click Back to
return to the Job Setup - Summary dialog box, or you can click Finish to exit the Job Setup
wizard.

Manually Defining Target and Tolerance values

1. Under Set Targets and Tolerances for, click the button corresponding to the patch type you want
to edit. For example, if you want to set target and tolerance values for inks used on Gray Balance
patch types, click Gray Balance. This opens the Job Targets and Tolerances dialog box.
2. Use the Target and Tolerance tabs to manually define the values for the job.
3. When you are satisfied with your settings, click OK to return to the Job Setup - Targets and
Tolerances dialog box.

Job Targets and Tolerances dialog box

Use the Job Targets and Tolerances dialog box to define target and tolerance values for each ink and
patch type used on the job. Use the Targets tab to set the target values, and the Tolerances tab to set
the tolerance values. To open the dialog box, click the appropriate button under Set targets and
tolerances for on the Job Setup - Targets and Tolerances dialog box .

7-4
 SETTING UP YOUR JOB

To set up target values for the selected patch type:

1. Select the Targets tab on the Job Targets and Tolerances dialog box.
2. As a default, only the Density target box is activated. Select the Let me change all targets check
box if you want to edit all applicable target values for this patch type.
NOTE: If you selected the Only watch density during makeready check box on the Defaults
tab of the Options dialog box, you can only edit the Density target values.
3. Each ink or ink combination associated with this patch type appears in the Ink list. Select the ink
or ink combination that you want to edit.
4. Type the target value in each of the available target type boxes.
As an alternative, you can click Set to Shop Target to use target values from an identical item in
the Target library. The Set to Shop Target function differs from the Shop Target function on the
Job Setup - Targets and Tolerances dialog box, as it allows you to use shop target values for one
specific ink or ink combination, rather than updating target values for all inks.
5. To change the filter used to read the target values for the current ink, you can select a different
filter from the Filter list.
6. If you edit any values for a specific ink (including setting the values to the shop target), a check
mark appears next to that ink. You can click Reset from Ink to restore the target values to the
original settings.
7. Repeat steps 3–6 for any other inks or ink combinations. When you finish setting up the targets,
you can either click OK to return to the Job Setup - Targets and Tolerances dialog box, or you
can select the Tolerances tab to edit tolerance values for this patch type.
To set up tolerance values for the selected patch type:
1. Select the Tolerance tab on the Job Targets and Tolerances dialog box.
2. As a default, only the Density tolerance boxes are activated. Select the Let me change all
tolerances check box if you want to edit all applicable tolerance types.
NOTE: If you selected the Only watch density during makeready check box on the Defaults
tab of the Options dialog box, you can only edit the Density tolerance values.
3. Under Width, you can select from Narrow, Medium, and Wide options. The selected option
determines which tolerance values are displayed. Therefore, you should select the appropriate
tolerance width (the width values that you want to edit) before changing the tolerance values for
each item. This setting only indicates which tolerance values are displayed and can be edited; it
does not determine which tolerance width is currently in use for the job. That is determined under
Tolerance Width on the Job Setup - Targets and Tolerances dialog box.
4. Each ink or ink combination associated with this patch type appears in the Ink list. Select the ink
or ink combination that you want to edit.
5. To enable a specific tolerance for the selected ink, select the check box next the tolerance value
box.
6. You can manually edit the Action and Control tolerance values based on the selected tolerance
width; select the tolerance value box that you want to edit, then type the new tolerance value.
As an alternative, you can click Set to Shop Tolerance to use the tolerances from an identical
item in the Tolerance library. The Set to Shop Tolerance function differs from the Shop Tolerance
function on the Job Setup - Targets and Tolerances dialog box, as it allows you to use shop
tolerances for one specific ink or ink combination, rather than updating tolerance values for all
inks.
7. Repeat steps 4–6 for any other inks or ink combinations. If you make any changes to the tolerance,
a check mark appears next to that ink in the list area. When you finish setting up the tolerances,

7-5
SECTION SEVEN

you can either click OK to return to the Job Setup - Targets and Tolerances dialog box, or you
can select the Targets tab to edit target values for this patch type.

Enable All Computations dialog box

Use the Enable All Computations dialog box to enable or disable specific tolerance types for each
patch type. The dialog box includes columns for each patch type, and rows for each tolerance type.
To enable a tolerance for a specific patch type, select the appropriate check box. For example, to
enable the Hue Error tolerance for a Solid patch type, select the Hue Error check box in the Solid
column.
NOTE: If you selected the Only watch density during makeready check box on the Defaults tab of
the Options dialog box, you can only use the Density tolerance type during the makeready phase of the
job.
When you finish setting up the tolerance information, click OK to save the new settings.

IDENTIFICATION DIALOG BOX

Use this dialog box to assign comments and tags to the job.
To enter job identification information:
1. In the Comments box, type any special notes or comments regarding this job.
2. Select the Use Dynamic Auto-Tracking check box if you want to system to verify the location of
each color before measuring.
NOTE: This check box does not appear if you have a battery-operated scanning head.
3. From the Status list, select the status to use for calculating and displaying density information.
4. The Absolute and Minus Paper options indicate the type of information used to calculate density
data. Select Absolute to include the substrate (paper) data in the density calculations. Select
Minus Paper if you do not want to include the substrate data in density calculations.
5. Under Job Tags, you can assign tags to the job. You can either enter new J ob tags or select from a
list of existing Job tags (where applicable). Type the tag text directly in the list box below the tag
type name, or select an existing tag from the list. Available tag types include:
· Paper Type - Use to describe the type of paper used in the job.
· Basis Weight - Use to describe the weight of the paper used in the job.
· Fountain pH - Use to describe press fountain pH level.
· Fountain Supplier - Use to identify the press fountain supplier.
· Blanket Type - Use to describe the press blanket type.
· Blanket Supplier - Use to identify the press blanket supplier.
· Ink Type - Use to describe the press ink type.
· Ink Supplier - Use to identify the ink supplier.
· Plate Type - Use to describe the type of press plate.
· Plate Supplier - Use to describe the plate supplier.
· Film Ruling - Use to describe the type of film ruling.
· Film Supplier - Use to describe the film supplier

7-6
 SETTING UP YOUR JOB

7. When you finish entering the identification information, click Finish to complete the Job Setup
wizard, or click Back to return to the Job Setup - Summary dialog box.

JOB PROPERTIES DIALOG BOX

Use the Job Properties dialog box to review the setup information for the current job. To open the
dialog box, choose Properties from the Job menu.
The Job Properties dialog box includes four tabs which correspond to similar dialog boxes in the Job
Setup wizard:
· The Press tab displays information from the Job Setup - Press dialog box.
· The Color Bars tab displays information from the Job Setup - Color Bars dialog box.
· The Identification tab displays information from the Job Setup - Identification dialog box.
· The Targets and Tolerances tab displays information from the Job Setup - Targets and
Tolerances dialog box.
While you can use these tabs to view the job parameters, you can only make minor changes through
this dialog box. To edit your job, use the Job Setup wizard.

7-7
SECTION SEVEN

7-8
 SECTION EIGHT

8. Recognizing Your Job

After you create and set up a job, you must recognize the job to ensure that the job information is
correct. You must also re-recognize a job whenever you change job information that affects the color
bar (such as ink colors, repeat patterns, or press type).
The ATD software incorporates an automated color bar recognition system: the Recognition wizard.
The wizard locates each color bar used on the job, and attempts to verify the recognized color bar data
with the color bar data that you defined during job setup. It then reports any discrepancies that exist
between the measured color bar and the color bar defined for the job. Each step in the recognition
process is displayed as a unique dialog box, with instructions to guide you through the procedure.
You can start the Recognition wizard in several ways:
· You can run the Recognition wizard directly from the Job Setup wizard. After you set up all
necessary job data, click Finish and Recognize on the Job Setup - Summary dialog box.
· If available, click Recognize on the Control Pane. (The Recognize button is only available if the
current job has not yet been recognized.)
· Press the button on your scanning instrument.
· From the Instrument menu, choose Recognize . This is the only way to initiate a re-recognition of
a job. Before performing a re-recognition, the system asks you to confirm that you want to
perform a new recognition. If you choose to re-recognize the job, you will lose all existing sheets
associated with the job.
Each step in the recognition process appears as a unique dialog box, with instructions to guide you
through the procedure. The wizard progresses slightly differently depending on whether or not you are
using the Auto-Advance function. In addition, the wizard may progress differently based on your
selections in the initial dialog boxes.
The Recognition wizard consists of the following dialog boxes:
· Select Recognition Type dialog box
If you are not using the Auto-Advance function, this dialog box appears as the first step in the
wizard. Use this dialog box to select the type of recognition that you want to perform
· Find Color Bars dialog box
If you are using the Auto-Advance function, this dialog box appears as the first step in the wizard.
If you are not using Auto-Advance, this dialog box only appears if you chose to find, scan, and
recognize each color bar. At this step in the wizard, you can edit the color bar information before
performing the actual recognition.
· Select Color Bars dialog box
This dialog box only appears if you chose to select specific color bars for recognition. Here you
select which color bars you want to recognize.
· Scan and Recognize dialog box
At this step, you can review the color bar as scanned by the instrument, and make any corrections
necessary before accepting the recognition data.
· Reposition Sheet dialog box
If you have color bars on more than one edge of the sheet, this dialog box will prompt you to
reposition the sheet so that the instrument can read the next edge.

8-1
SECTION EIGHT

· Final Results dialog box

After all color bars on all sheet edges have been recognized, this dialog box displays a summary of
the recognition information.

SELECT RECOGNITION TYPE DIALOG BOX

If you are not using the Auto-Advance function, you can select how you want to recognize the color
bars. Two recognition types are available: you can find, scan, and recognize each color bar on the
sheet, or you can select specific color bars to scan and recognize.
To select the recognition type:
1. Under Types of Recognition, select how you want to recognize data. Select Find, Scan, and
Recognize each color bar if you want the system to automatically locate, scan, and recognize
every color bar on the sheet. Select Scan and Recognize selected color bars if you want to select
specific color bars for re-recognition.
NOTE: The Scan and Recognize… option is only available if you are performing a re-
recognition of a previously recognized job.
2. Click Next to continue. If you selected the Find, Scan, and Recognize… option, the Find Color
Bars dialog box appears. If you selected the Scan and Recognize… option, the Select Color
Bars dialog box appears.

SELECT COLOR BARS DIALOG BOX

This dialog box appears if you chose to scan and recognize selected color bars. Here you select the
specific color bars you want to re-recognize. Since this option is only available for jobs which have
already been recognized, the system does not need to find the color bars.
All color bars on the first edge appear in the list area. Select each color bar that you want to re-
recognize. Click Next to continue to the next step: the Scan and Recognize dialog box.

FIND COLOR BARS DIALOG BOX

If you are using the Auto-Advance function, this dialog box appears as the first step in the wizard. It
also appears if you chose to find, scan, and recognize all of the color bars on the job. Here you can
select and prepare each color bar for recognition.
NOTE: The Find Color Bars dialog box appears for each edge of the sheet that contains color bars. If
your job includes color bars on more than one edge of the sheet, the system will return to this dialog
box after you have located, scanned, and recognized the color bars on each edge.
The first time the Find Color Bars dialog box appears, the scanning instrument locates all color bars
on the current sheet edge. The system displays a message informing you that scanning is in process as
the scanning instrument measures the current edge. After this initial scan has been successfully
completed, the system displays the color bar information in the list area of the dialog box.
To find color bars:
1. If necessary, click Find Color Bars to re-scan the current edge.
2. From the list area, select the color bar that you want to recognize.
3. If you want to edit the color bar setup, click Edit Color Bars on this Edge. You can then modify
the color bar repeat using the Job Setup - Color Bars dialog box.
4. If the color bar you want to recognize is not displayed in the list area, you may need to manually
define specific location of the color bar on the current sheet edge. Click Specify Position to set the
X and Y values on the Recognition Wizard - Specify Position dialog box.

8-2
 RECOGNIZING YOUR JOB

5. If the instrument is not accurately reading the color bar, you may want to adjust the default offset
positions from the sheet edges. These values represent the distance the scanning head covers
before reading the color bar data. Under Options, type the correct values or use the arrow buttons
to select the values.
6. When you are ready to recognize the selected color bar, click Next. The system automatically
scans and recognizes the color bar, then displays the recognition information in the Scan and
Recognize dialog box.
NOTE: The system recognizes each color bar individually. If there are multiple color bars on this
sheet edge, the system will return to this dialog box after the first color bar has been recognized. You
can then recognize the next color bar on the current sheet edge.

SPECIFY COLOR BAR POSITION DIALOG BOX

If you cannot identify the current color bar in the list on the Find Color Bars dialog box, you can use
the Specify Color Bar Position dialog box to manually define the starting and ending location of the
current color bar.
You specify the color bar position by entering the offset positions of the color bar. In the X and Y
boxes for the left and right edges, type the correct value, or use the arrow buttons to select the value.
Once you have entered the correct values, click Next to move to the next step: Scan and Recognize.

SCAN AND RECOGNIZE DIALOG BOX

After the software recognizes the current color bar, it displays the color bar data in the Scan and
Recognize dialog box. You can adjust the color bar parameters if necessary, and when you are
satisfied with the results, you can accept the recognition data

To review, adjust, and accept color bar information:

1. Identify any errors in the recognition. Under Recognition Statistics, the system displays the
percentage of the color bar which was actually recognized, the number of patches in the color bar,
and the number of “duds”.
NOTE: A dud refers to any patch type which should include useful information (including
patches defined as unused or as paper patches), but which was not recognized as a valid patch
during the scan.
A visual representation of the color bar is displayed in the center of the dialog box. You can move
the display to the next dud patch by clicking Next Dud. (If there are no duds, the Next Dud button
is unavailable). Any patch which is identified as a dud is not used in subsequent scans. If it is not
recognized now, you cannot use that patch data for later analysis when measuring sheets for the
job.
2. If the library color bar and the recognized color bar are not properly aligned, click Adjust
Repeats. You can then re-align the color bars on the Adjust Repeats dialog box.
3. If any of the patch information is incorrect, click Adjust Patches. You can then edit the patch data
on the Adjust Patches dialog box.
4. If you want to edit ink information or change some of the press settings, click Job Setup. This
opens the Job Setup wizard; while you cannot edit all of the job setup information, you can add,
remove, or change inks; reorder inks in the press or color bar; change the sheet color; and change
the width of keys on the press. If any you change any of the color bar data, you must re-scan the
color bars.
5. If you changed the color bar data and need to re- recognize the updated color bar information, use
the Scan and Recognize buttons. Click Scan to re-scan the sheet edge and re-recognize the color
bar; click Recognize to perform a new recognition.

8-3
SECTION EIGHT

6. When you are satisfied with the color bar data, click Next to accept the recognition and continue.
The next step depends on your individual job:
· If this is the last (or only) color bar in the job, the recognition process is complete. The Final
Results dialog box appears.
· If there are additional color bars on the current edge, the Find Color Bars dialog box appears.
You must repeat the scan and recognition process for each color bar on the current edge.
· If all color bars on the current sheet edge have been recognized and there are color bars
located on other edges of the sheet, the Reposition Sheet dialog box appears. You are then
prompted to reposition the sheet so the color bars on the next edge can be scanned and
recognized.

Adjust Repeats dialog box

Use the Adjust Repeats dialog box to edit the repeat (the sequence of patches) of the current color bar.
The dialog box displays two color bar repeats. The repeat as set up in the Color Bar library appears
first, and the repeat as it was identified on the last recognition appears below it.
To align the color bars, use the scroll bars to properly match up the repeat sequence. You can then
"lock" the alignment into place by selecting corresponding patches in each color bar. If necessary, you
can click Reverse to reverse the order of the Library color bar repeat.
When you have properly aligned the color bars, click OK.

Adjust Patches dialog box

Use the Adjust Patches dialog box to individually change patch assignments on the current color bar.
The color bar name and comments, as entered during job setup, appear at the top of the dialog box. A
diagram of the recognized color bar appears at the bottom of the dialog box. Use the horizontal scroll
bar to move through diagram, or click Next Dud to move to the next dud in the color bar repeat.
To edit a specific patch on the color bar:
1. On the color bar display, select the patch that you want to edit.
2. If you want to change the patch type or inks, select the Show Patch Editor check box. The Edit
Patch dialog box appears, and you can edit the patch type, inks, and related patch information.
3. To change the key assignment for a specific patch, select the patch, then enter the appropriate key
number in the Key box.
4. To change a patch to a "not used" patch type, select the patch, then select the Not Used check box.
5. When you finish making changes, click OK to save the new patch settings.

REPOSITION SHEET DIALOG BOX

This step only appears if the job includes color bars on more than one sheet edge. After all of the color
bars on the first edge have been recognized, the Reposition Sheet dialog box prompts you to move the
sheet so the color bars on the next edge can be recognized.
After you correctly position the sheet, click Next to continue. The Find Color Bars dialog box
appears.

FINAL RESULTS DIALOG BOX

After the recognition process is complete (the system has successfully recognized each color bar used
on the job, or each color bar that you selected for re-recognition), the Final Results dialog box
appears. This dialog box lists the name of the color bars, the total number of patches on each color bar,
the number of duds, and the final recognition percentage.

8-4
 RECOGNIZING YOUR JOB

If you want to use these recognition scans to create the first sheet of the job, select the Use initial
scan(s) as the first sheet in the job check box. The system will automatically create a sheet based on
the recognition scans. Click Finish to complete the recognition process. You can then use the
Measurement wizard to start measuring sheets for the job.

8-5
SECTION EIGHT

8-6
 SECTION NINE

9. Measuring Your Job

The Measurement wizard walks you through each step required to add the sheet data to the job. It
prompts you to measure each color bar defined on the sheet. Each step in the measurement process
appears as a unique dialog box, with instructions to guide you through the procedure.
To measure a sheet:
1. From the Instrument menu, choose Scanning, then choose Measure. This starts the
Measurement wizard. (You can also click Measure on the Control Pane to start the wizard).
2. The system measures the first color bar on the current sheet edge and displays the measurement
data on the Measure Color Bars dialog box. After you accept the measured data, the process is
repeated for each color bar on the current sheet edge.
3. If the job includes color bars on more than one edge of the sheet, the Reposition Sheet dialog box
appears. After you correctly position the sheet, the Measure Color Bars dialog box appears for
the first color bar on the new sheet edge.

MEASURE COLOR BAR DIALOG BOX

Once started, the Measurement wizard automatically measures the first color bar on the current sheet
edge, then displays the color bar data in this dialog box.
If necessary, you can click Measure to re-measure the color bar. If you want the system to verify the
location of the color bar before measuring, select the Use Dynamic Auto-Tracking on this
measurement check box.
NOTE: This check box does not appear if you have a battery-operated scanning head.
A diagram of the measured color bar appears in the center of the dialog box. You can use the
horizontal scroll bar to move through the diagram, or you can click Next Dud to move to the next dud
patch. (If there are no duds, the Next Dud button is unavailable).
When you are satisfied with the current measurement, click Next or Finish, as applicable:
· If there are additional color bars on the current edge, click Next to repeat the measurement
process. Continue until all color bars on the current edge are measured.
· If you have measured all the color bars on the current sheet edge, but need to measure color bars
on a different edge of the sheet, click Next to open the Reposition Sheet dialog box.
· If this is the last (or only) color bar, the measurement process is complete. Click Finish to exit the
wizard. You can view the sheet data in the current job window, and print a report of the data if
necessary.
NOTE: If you are using the Auto-Advance function, the software will automatically close the wizard at this
point.

REPOSITION SHEET DIALOG BOX

This step only appears if the job includes color bars on more than one sheet edge After all the color
bars on the first sheet edge have been measured, the Reposition Sheet dialog box prompts you to
move the sheet so the color bars on the next edge can be recognized.
After you correctly position the sheet, click Next to return to the Measure Color Bars dialog box.

9-1
SECTION NINE

9-2
 SECTION TEN

10. Retargeting Your Job

Use the Retarget function to specify new target values for the job. The effect of retargeting is based on
the setting of the Retarget All Sheets Whenever Targets change check box on the Defaults tab of
the Options dialog box. If you select this check box, all sheets on the job are retargeted to the new
values. If you do not select this check box, only new sheets (sheets measured after you retarget the job)
use the new target values.
NOTE: You cannot retarget a job from a satellite workstation.
You retarget your job using the Retarget dialog box. From the Job menu, choose Retarget to open the
dialog box. (You can also click Retarget on the Control Pane to open the dialog box). You can use
several different methods to retarget your job.

RETARGETING THE JOB TO THE CURRENT SHEET

1. From the Job menu, choose Retarget. The Retarget dialog box appears.
2. If you want to move the job to the production phase, select the Enter Production check box. If
you select this check box, the system tags every new sheet as a production sheet.
3. Click Set Sheet # as OK Sheet. The system retargets the job using the values from the current
sheet.
NOTE: If you use this method of retargeting, an icon will appear next the Retarget button on the
Control Pane to indicate that the job was retargeted.
You can also use the Retarget command on the Sheet submenu of the Tools menu to retarget the job
to the current sheet.

RESETTING THE JOB TO ORIGINAL TARGET VALUES

1. From the Job menu, choose Retarget. The Retarget dialog box appears.
2. If you want to move the job to the makeready phase, select the Enter Makeready check box.
When this check box is selected, you can also select the Only watch density during makeready
check box if you only want to use the Density tolerance values during the makeready phase of the
job.
3. Click Reset to Original Targets. The system restores the job targets to the original target settings.

MANUALLY DEFINING NEW TARGET VALUES

1. From the Job menu, choose Retarget. The Retarget dialog box appears.
2. If you want to move the job to the makeready phase, select the Enter Makeready check box.
When this check box is selected, you can also select the Only watch density during makeready
check box if you only want to use the Density tolerance values during the makeready phase of the
job.
3. Click Change Targets. The Job Targets dialog box appears.
4. As a default, only the Density target box is activated. Select the Let me change all targets check
box if you want to edit all applicable target values for this patch type.
NOTE: Depending on the current job phase (makeready vs. production) and the setting of the
Only watch density during makeready check box, you may not be able to edit all of the target
values

10-1
SECTION TEN

5. From the Inks list, select the ink or ink combination that you want to edit.
6. Type the new target value in each of the available target type boxes.
As an alternative, you can click Set to Shop Target to use target values from an identical item in
the Target library.
7. To change the filter used to read the target values for the current ink, select a different filter from
the Filter list.
8. If you edit any values for a specific ink (including setting the values to the shop target), a check
mark appears next to that ink. You can click Reset from Ink to restore the target values to the
original settings.
9. Repeat steps 5–8 for any other inks or ink combinations.
11. Click OK to use the new target values on the job.

CHANGING THE STATE OF A JOB

1. From the Job menu, choose Retarget. The Retarget dialog box appears.
2. If you want switch the job to the makeready phase, click Enter Makeready Now. (This button is
only available if the job is currently in the production phase.)
3. If you want to switch the job to the production phase, click Enter Production Now. (This button
is only available if the job is currently in the makeready phase.)

10-2
 SECTION ELEVEN

11. Retolerancing Your Job

The Retolerance function allows you to specify new tolerance values for the job. The system uses the
new tolerance values for all new measurements.
NOTE: You cannot retolerance a job from a satellite workstation.
You retolerance your job using the Retolerance dialog box. From the Job menu, choose Retolerance
to open the dialog box. (You can also click Retolerance on the Control Pane to open the dialog box.)

MANUALLY DEFINING NEW TOLERANCE VALUES

1. From the Job menu, choose Retolerance. The Retolerance dialog box appears.
2. Under Tolerance width, select the tolerance width that you want to use for the job.
3. If you want to move the job to the makeready phase, select the Enter Makeready check box.
When this check box is selected, you can also select the Only watch density during makeready
check box if you only want to use the Density tolerance values during the makeready phase of the
job.
4. Click Change Tolerances. The Job Tolerances dialog box appears.
5. As a default, only the Density tolerance boxes are activated. Select the Let me change all
tolerances check box if you want to edit all applicable tolerance types.
NOTE: Depending on the current job phase (makeready vs. production) and the setting of the
Only watch density during makeready check box, you may not be able to edit all of the
tolerance values
6. Under Width, you can select from Narrow, Medium, and Wide options. The selected option
determines which tolerance values are displayed. Therefore, you should select the appropriate
tolerance width (the width values that you want to edit) before changing the tolerance values for
each item. This setting only indicates which tolerance values are displayed and can be edited; it
does not determine which tolerance width is currently in use for the job. That is determined under
Tolerance Width on the Retolerance dialog box.
7. From the Inks list, select the ink or ink combination that you want edit.
8. To enable a specific tolerance for the selected ink, select the check box next to the tolerance value
box.
9. You can manually edit the Action and Control tolerance values based on the selected tolerance
width; select the tolerance value box that you want to edit, then type the new tolerance value.
As an alternative, you can click Set to Shop Tolerance to use the tolerances from an identical
item in the Tolerance library.
10. Repeat steps 7–9 for any other inks or ink combinations. If you make any changes to the tolerance,
a check mark appears next to that ink in the list area.
11. Click OK to use the new tolerance values on the job.

ENABLING AND DISABLING TOLERANCE TYPES

1. From the Job menu, choose Retolerance. The Retolerance dialog box appears.
2. Under Tolerance width, select the tolerance width that you want to use for the job.

11-1
SECTION ELEVEN

3. Click Enable All Tolerances. The Enable all Computations dialog box appears, where you can
select which tolerance types you want to use.
4. When you finish making your selections, click OK to use the new tolerance settings.

11-2
 SECTION TWELVE

12. Viewing Job Data

Measurement data for each open job is displayed in individual job windows on the ATD desktop. The
type of data displayed is based on the current key and sheet selected on the Control pane, and the
current view type selected on the job window. Within the individual views, you can customize the job
window by adding and removing graphs, changing the sheet range or key range used, and turning
specific press keys on or off.

THE VIEW TYPES

There are three different view types, which you can activate by selecting the appropriate tab at the
bottom of the job window (or by choosing the desired view from the View menu):
· Key Trend View
· Sheet Trend View
· Press Status View
The Trend views allow you to view multiple keys or sheets at one time. Using these views, you can
then identify trends in your press run. There are common functions within the Key Trend and Sheet
Trend views. These views display the same type of data from two different perspectives. Key view
graphs show data for each key on a single sheet, while Sheet view graphs show data for each sheet at a
single key location. The graph data exists in a three-dimensional space consisting of an attribute, the
time, and location.

Using the Key Trend View

The Key Trend View displays measurement data in a bar graph. One graph is displayed for each ink
color used on the job. Within each graph, a single bar is displayed for each key used on the job; each
bar represents the actual or difference value of the attribute for the selected sheet at that specific key
location. You can use the Sheet slider on the Control Pane to view key trend data for other sheets in the
job.
The graph bars are color-coded to indicate status: if the value is within all tolerance limits, it is
displayed in green; if it extends outside of the action limits, but is within the control limits, it is
displayed in yellow; if it extends outside the control limits, it is displayed in red. If no limits have been
defined, the graph bars are displayed in white.
You can view the key trend values by “hovering” over the desired key with your mouse pointer
(position the cursor over the key and pause until text appears). A description box displays the key
number and either the actual or difference value, as applicable. You can display all key trend values by
choosing Show Key Trend Values from the Graph menu.
You can view either Difference data or Actual data. To change between the two options, choose Make
all Difference or Make All Actual from the Graph menu. Data appears differently depending on your
selection, as follows:
· When difference values are plotted on the Key Trend graph, the vertical graph bars are plotted
either upwards or downwards from the center of the graph (the X-axis). The vertical bars are
plotted from the center axis based on the magnitude and direction of difference for a given key. If
action and control limits are set for an attribute, horizontal lines show the action and control limits
(the graph lines are displayed in yellow and red, respectively).
· When actual values are plotted on the Key Trend graph, the vertical graph bars are plotted
upwards from the bottom of the graph (the X-axis). The magnitude of the vertical bar is based on

12-1
SECTION TWELVE

the actual value of the attribute—not on the difference between it and its target value—for the
selected key.
To display more detailed data, you can use the Zoom mode.

Using the Sheet Trend View

The Sheet Trend View plots individual points on the graph to represent each measurement. Each point
represents one sheet, and multiple sheet measurements are displayed as a line graph. This line graph
shows measurement trends from one sheet to the next. (A maximum of 30 sheets can be displayed on a
single graph). The color of the points indicate the status: if a point is within all action and control
limits, it is displayed in green; if it exceeds an action limit but is within control limits, it is displayed in
yellow; if it exceeds a control limits, it is displayed in red.
You can view either Difference data or Actual data. To change between the two options, choose Make
all Difference or Make All Actual from the Graph menu. Data appears differently depending on your
selection, as follows:
· When difference attributes are plotted on the Sheet Trend graph, the graph points are plotted either
upwards or downwards from the center of the graph (the X-axis). The points are plotted from the
center axis based on the magnitude and direction of difference. In addition, horizontal lines above
and below the center axis show the high and low action and control limits. (If limits have not been
defined for an attribute, no lines are displayed.)
· When actual values are plotted on the Sheet Trend graph, the graph points are plotted upwards
from the bottom of the graph (the X-axis). The points represent the actual value of the attribute
(not the difference between it and its target value).
To display more detailed data, you can use the Zoom mode.

Using the Press Status View

The Press Status view provides a quick reference to the ink colors and printing units on the press used
with the current job. It allows you to quickly determine whether or not the press is working within the
tolerances specified.
The Press Status view contains several components:
· Press Diagram. The press diagram is a simple graph with custom color codes to indicate the
various components. If desired, you can double-click the diagram to display the job Status dialog
box.
· Alert Indicators. Alert indicators information you of any value that is out of tolerance for a
particular printing unit. The alert indicators change colors to indicate the state of the printing unit,
as follows:
White indicates that the printing unit is not used or no appropriate tolerance limits are set.
Green indicates that all calculated values are within all tolerance limits.
Yellow indicates that some values exceed action limits, but all values are still within the control
limits.
Red indicates that some values exceed the control limits.
In addition to the printing unit indicators, two additional alert indicators display the status for
Overprint and Gray Balance patch types. These indicators use the same color coding system
described above.
· Ink Indicators. The ink indicators provide a visual representation of the ink color actually used in
each printing unit. These indicators display the color as found on the color bar; no additional data
about the colors is provided in this view. If no ink colors are defined, these display in black. If a
specific printing unit is not used, that ink color indicator is displayed in white.

12-2
 VIEWING JOB DATA

· Press Identification. The Press Name is displayed at the top of the diagram, and the Press Type is
displayed at the bottom of the diagram.

Using the Zoom Mode

The Zoom mode, which can be used with either of the Trend views, enhances the current view to show
a single graph and a corresponding data window. This mode provides more detailed data for the
current graph. From the Graph menu, choose Zoom to activate the Zoom mode for the current graph.
In the Zoom mode, you can view either Statistics or Error information. Choose the appropriate option
from the bottom of the Zoom window. When you display Statistics data, the specific values of different
attributes (such as the actual value of the current key or sheet, average values, minimum and maximum
ranges, and difference values) are listed in table form in the data window. The type of values displayed
depend on the current view type. When you display Errors data, you can view the details on any keys
or sheets that exceed Action or Control limits on the current graph.

CUSTOMIZING VIEWS AND GRAPHS

The commands on the Graph menu allow you to manipulate how data is displayed in the current view.
When viewing individual graphs within a specific view type, you can select (“activate”) a specific
graph by clicking the graph label. The active graph is indicated with highlighted label text. It is
important to identify the active graph before selecting commands on the Graph menu, as some affect
an entire view, and others only affect the active graph within the view.
NOTE: Graph commands are not available for the Press Status view.
In addition to using the Graph menu, you can also access many of these functions through shortcut
keys or toolbar buttons.

Adding a Graph to the Current View

Use the Add Graph dialog box to add a graph to the current view. The options available on this dialog
box depend on the type of view window you are using and on your job settings. To open the dialog
box, choose Add from the Graph menu.
To add a graph to the current view:
1. From the Computation Type list, select the computation type to use for this graph. You can only
select computation types that are supported for the current View type and are used on the job.
2. From the Patch Type list, select the type of patch data you want to display on this graph. You can
only select patch types that are supported by the selected computation type and are used on the
job.
3. From the Inks list, select the ink (or combination of inks) that you want to display on this graph.
You can only select inks that are available for the selected patch type.
4. Select the Difference check box if you want the graph to display data based on the difference
values. If you want to display actual values, make sure you do not select this check box.
5. Select additional graph information as necessary, based on the calculation type selected:
· From the Status list, select the Density Status to use to generate graph data.
· From the Filter list, select the filter to use for the graph. (This list is not available for
Grayness or Hue Error computation types.)
· Under Graph Type, select how you want to use paper data in the in the graph calculations.
Select Absolute if you want to include the paper (substrate) data in calculations. Select
Relative if you want paper data subtracted from calculations.

12-3
SECTION TWELVE

6. When you are satisfied with your graph settings, click OK to add the new graph to the current
view window.

Adding Multiple Graphs to the Current View

Use the Add Multiple Graphs dialog box to add a group of graphs to the current view. From the
Graph menu, choose Add Multiple to open the dialog box.
NOTE: When you use this function, the new graphs replace any previously displayed graphs.
You can either add graphs based on a selected computation type and patch type, or based on a selected
ink or ink combination.
To add graphs based on a computation/patch type:
1. Click Show graphs for a specified computation and patch type.
2. From the list area on the left side of the dialog box, select the computation type/patch type
combination that you want to use to create graphs.
3. Click OK. A new graph is created for every ink or ink combination associated with the selected
computation/patch type.
To add graphs based on a selected ink:
1. Click Show graphs for a specified ink or combination of inks.
2. From the list area on the right side of the dialog box, select the ink or ink combination that you
want to use to create graphs.
3. Click OK. A new graph is created for every computation/patch type that uses the selected ink.

Changing the Current Graph

Use the Configure Graph dialog box to change the setup of the current graph. From the Graph menu,
choose Configure to open the dialog box.
You can then change the graph settings using the same steps used to add a new graph. Click OK to
update the current graph with the new settings.

Removing Graphs from the Current View

You can remove graphs from the current view in two different ways: you can just remove the current
graph, or you can clear all of the graphs from the current view.
To remove the current graph, choose Remove from the Graph menu.
To remove all of the graphs from the current view, choose Remove All from the Graph menu. Before
clearing the current view, the system asks you to confirm the removal. Click Yes to remove all graphs,
or No to cancel the process.

Moving Through Graphs

From the Graph menu, choose Next to activate the next graph in the current view window. Choose
Previous to activate the previous graph.

Selecting the Sheet Range

Use the Sheet Analysis Range dialog box to select the range of sheets to use to generate graph data.
As a default, the system uses all sheets in the job. All calculated values are based on the specific range
of sheets currently in use.
From the Tool menu, choose Sheet, then choose Analysis Range to open the dialog box.

12-4
 VIEWING JOB DATA

To adjust the sheet analysis range:

1. Select the Enable Range check box to activate the Starting Sheet and Ending Sheet boxes. If
you do not select this check box, you cannot set a specific sheet range—the default of ALL sheets
will be used.
2. Enter the range of sheets that you want to use. In the Starting Sheet box, type the number of first
sheet in the range; in the Ending Sheet box, type the number of the last sheet in the range. You
can also use the arrow buttons to select the sheet numbers.
3. Click OK to set the sheet analysis range for the active job.

Moving Through Sheets

You can move through all of the sheets on the current job by using the sheet slider control on the
Control Pane, or by using the commands on the Sheet submenu of the Tools menu:
· Choose First to move to the first sheet in the job.
· Choose Previous to move to the previous sheet in the job.
· Choose Next to move to the next sheet in the job.
· Choose Last to move to the last sheet in the job.
· Choose Last Retargeted to move to the last sheet that was used to generate target values.

Moving to a Specific Sheet

Use the GoTo Sheet function to move directly to a specific sheet in the job.
To move to a specific sheet:
1. From the Tools menu, choose Sheet, then choose Goto. The Enter Val ue dialog box appears.
2. In the Sheet Number box, type the number of the sheet that you want to view, or use the arrow
buttons to select the sheet number.
3. Click OK to display the selected sheet.

Selecting the Key Range

Use the Key Viewport dialog box to select the range of keys to use to generate graph data. As a
default, the system uses all keys in the job. All calculated values are based on the specific range of
keys currently in use.
From the Tools menu, choose Keys, then choose Viewport to open the dialog box.

To adjust the key viewport:

1. This opens the Key Viewport dialog box.
2. Select the Enable Range check box to activate the Starting Key and Ending Key boxes. If you
do not select this check box, you cannot select a specific key range—the default of ALL keys will
be used.
3. Enter the range of keys that you want to use. In the Starting Key box, type the number of the first
key in the range; in the Ending Key box, type the number of the last key in the range. You can
also use the arrow buttons to select the key numbers.
4. Click OK to set the key viewport for the active job.

12-5
SECTION TWELVE

Moving Through Keys

You can move through all of the keys on the current job by using the key slider control on the Control
Pane, or by using the commands on the Key submenu of the Tools menu:
· Choose First to move to the first key in the job.
· Choose Previous to move to the previous key in the job.
· Choose Next to move to the next key in the job.
· Choose Last to move to the last key in the job.

Moving to a Specific Key

Use the GoTo Key function to move directly to a specific key in the job.
To move to a specific key:
1. From the Tools menu, choose Key, then choose Goto. The Enter Value dialog box appears.
2. In the Key Number box, type the number of the key that you want to view, or use the arrow
buttons to select the sheet number.
3. Click OK to display the selected key.

Turning Keys On and Off

Use the Manage Keys dialog box to enable or disable specific keys on the current press. From the
Tools menu, choose Keys, then choose Manage Keys to open the dialog box.
To turn keys on and off:
1. All of the inks used on the press appear as individual options on the right side of the dialog box.
To turn keys on or off for a specific ink, select the option button for the ink that you want to use.
To turn keys on or off for all inks, select the Press (all inks) option.
2. All of the keys associated with the selected ink appear in the Key Status list. To turn a specific
key on, select the check box for that key; to turn a key off, clear the check box for that key.
3. When you finish making your key selections, click OK to save the settings and close the dialog
box.
NOTE: If you turn keys off, the new settings affect the most recently scanned sheet and all future
sheets. If you turn keys on, the new settings only affect future sheets.

Showing Key Trend Values

If you are using the Key Trend view, you can display the actual key values on each bar of the graph.
To display key trend values, choose Show Key Trend Values from the Graph menu.

Printing Graph Data

You can print graph data in two different ways: you can either print a graphical representation of the
current view window, our you can print a statistical report of the graph data.
To print a graphical representation, choose Print from the Graph menu.
To print a statistical report, choose Report from the Graph menu. You can then set up the printing
options on a standard Windows Print dialog box.
To print more detailed data, use one of the ATD report formats.

12-6
 VIEWING JOB DATA

Increasing and Decreasing Vertical Scaling

From the Graph menu, choose Increase Vertical Scaling to increase the vertical scaling of the current
graph (“zoom out”). Choose Decrease Vertical Scaling to decrease the vertical scaling of the current
graph (“zoom in”).
When you increase the scaling, the range on the Y-axis increments in a 1,2,3, sequence and rages from
a maximum of 5 to a minimum of -5.

Displaying Difference or Actual Data

If you want to display difference data (variation from target values) on the current graph, choose All
Difference from the Graph menu. If you want to display the actual values, choose All Actual from
the Graph menu.

Using Full Screen view

Use the full screen view to expand the current view window to the entire screen area (so the Control
Pane, tool bar, and menus are no longer displayed). This can be helpful if you want to review the
maximum number of graphs at one time. To activate the full screen view, choose Full Screen from the
View menu. You can use the buttons on the small toolbar to change the view options, as follows:
· Click the Full Screen button to return to normal view mode.
· Click the Control Pane button to display or remove the Control Pane.
· Click the Toolbar button to display or remove the standard ATD toolbar.
· Click the Status Bar button to display or remove the status bar.

12-7
SECTION TWELVE

12-8
 SECTION THIRTEEN

13. Printing Job Data

The ATD software provides several different types of reports, which you can use to print all different
types of job data. The following reports are supported in ATD:
· Custom report
· Job Summary report
· Single Sample Single Attribute report
· Trend Analysis report
NOTE: You can review and print more detailed information using the Statistical Process Control
program.
In addition, you can use the Print File Utility to print reports that were originally sent to a file l ocation,
rather than to a printer.

USING CUSTOM REPORTS

The Custom Report function uses the Crystal Reports software to generate report data in ATD. The
data printed on any custom report is based on the view type (for example, Sheet Trend or Key L*a*b*)
in use when the report is selected.
A custom report, as setup through Crystal Reports, contains fields for the current sheet and current
patch; when the report is generated in ATD, the software updates these values based on the data in the
current view. For more information on creating new custom reports, refer to the Crystal Reports
software documentation.

Generating a Custom Report

1. From the Reports menu, choose Custom. The Custom Reports dialog box appears.
2. From the Report Names list, select the report you want to generate.
3. Click OK to generate the report. If you report was set up to be printed, the standard Windows
Print dialog box appears, and you can select your print options. If the report was set up to
exported to file, a standard Windows dialog box appears where you can select the file location.

Adding or Editing a Custom Report

NOTE: You can only add report files which have already been created in the Crystal Report
application. For additional information, refer the Crystal Reports software documentation.
1. From the Reports menu, choose Custom. The Custom Reports dialog box appears.
2. Click Add to open the Add Custom Report dialog box.
NOTE: To edit an existing report, select the report you want to edit from the Report Names list,
and then click Edit.
3. In the Report Path box, type the path and file name of the report you want to add, or click the
Browse button (…) to select the path and file from a standard Windows Open dialog box.
4. In the Name of Report box, type a name for this report. The name entered here is used to identify
this report in the Custom Reports dialog box.
5. Select what sheet data to include on this report:

13-1
SECTION THIRTEEN

· Select Current Sample to generate report data for current sheet only.
· Select All Samples to generate data for all sheets in the job.
6. Select the destination (print or export) for this report.
· Select Ask if you want the system to ask the user for the report destination at the time the
report is generated.
· Select Print to Default Printer to automatically print the report to the default printer once the
report is generated.
· Select Export to File to automatically export the report data to a specified file when the
report is generated. If you select this option, you must select the file format and export
location. From the Format Type list, select the format to use for the exported data. In the
Export File Path box, type the drive and folder path to which you want to export the file or
click the Browse button (…) to select the path from a standard Windows Save As dialog box.
7. When you are satisfied with your report settings, click OK.

Deleting a Custom Report

1. From the Reports menu, choose Custom. The Custom Reports dialog box appears.
2. From the Report Names list, select the report you want to delete.
3. Click Delete.

USING THE JOB SUMMARY REPORT

The Job Summary report provides a complete analysis of the entire press run, categorizing defects by
ink color. Because this report includes information about the entire job, it may take several seconds to
generate. You can output the report to a printer or export the report data to a file.
To create a Job Summary report, choose Job Summary from the Report menu. The report is
automatically generated for the current job. After the report is generated, you can select your output
options in the Print dialog box.
The Job Summary report is divided into five areas:
· Page Header
· Job Information
· Summary of All Computations and All Inks
· Summary of All Totals
· Ending Percentages

Page Header
The Page Header of the Job Summary report is printed on each page of the report, and contains general
information identifying the report. Header information includes:
· the date on which the report was generated.
· the Company Name (as entered on the General tab of the Options dialog box).
· the page number.
· the name of the report (Job Summary report).
· the name of the project associated with this job.

13-2
 PRINTING JOB DATA

· the name of the job.

· any comments for the job (as entered on the Identification dialog box during Job Setup).
· the date on which the job was created.

Job Information
The Job Information portion of the Job Summary report lists some of the parameters defined during job
setup, as follows:
· Response—the density status selected for use with this job.
· Color Bars—all color bars used on this job.
· Location—each edge of the sheet (for example, Gripper/Front, Trailing/Front) used on the job,
and the color bars used at each location.
· Press Name—the name of the press used on this job.
· Press Comments—any comments associated with this press.
· Limit Set—the tolerance width (Narrow, Medium, or Wide) used for this job.
· Blanket Type/Blanket Supplier/Fountain PH/Fountain Supplier—any tags of these specific
types assigned to the job.

Summary of All Computations and All Inks

This section of the Job Summary report lists summary information for each computation type as it
relates to all of the ink colors used on the job. Only computation types and patch types with actual
measurement data are included on the report. Information is arranged by ink. Each ink area lists all
applicable computation/patch type combinations. The following information is reported for each
computation/patch type combination associated with each ink:
· Total Keys—the total number of keys.
· Key Out—the total number of keys outside of the tolerance limits.
· Percent Out—the percent of keys outside of the tolerance limits.
· Mean Value—the average density values across all keys.
· Min Value—the minimum density value across all keys.
· Max Value—the maximum density value across all keys.
· Range—the density range value across all keys.
· Std Dev—the standard deviation across all keys.
The total values for all computation/patch type combinations appear at the bottom of each ink area.

Summary of All Totals

This section of the Job Summary report lists total values for all inks. The following totals are listed for
all ink, overprint, and gray balance patch types:
· Total Keys—the total number of keys for each computation type.
· Keys Out—the total number of keys outside of the tolerance limits for each computation type.
· Percent Out—the percent of keys outside of the tolerance limits for each computation type.
The total values for the entire job appear at the bottom of the Summary area.

13-3
SECTION THIRTEEN

Ending Percentages
The Ending Percentages portion of the Job Summary report lists the total number of keys that are
within tolerance limits and the total number of keys that are outside of the tolerance limits for the
entire job. The total number of sheets appears at the end of the report.

USING THE SINGLE SAMPLE SINGLE ATTRIBUTE REPORT

The Single Sample Single Attribute Report lists all data for an specific computation/patch type
combination on a single sheet. Because of this, you need to define your report parameters before the
report can be printed.
The Single Sample Single Attribute report is divided into four areas:
· Page Header
· Sample Information
· Key Data
· Statistics

To generate a Single Sample Single Attribute report:

1. From the Report menu, choose Single Sample Single Attribute. The Single Sample Single
Attribute Report Options dialog box appears
2. In the Sample box, type the number of the sheet for which you want to generate the report data, or
use the arrow buttons to select the sheet number.
3. From the Computation list, select the computation type for which you want to generate the report
data. You can only select computation types supported on the current job.
4. From the Patch Type list, select the patch type for which you want to generate the report data.
You can only select patch types supported by the selected computation type.
NOTE: To obtain a quick report on the status of a sheet, select the Density computation type and the Solid
patch type. This generates a single page report, while all other attribute selections print one page per ink.
5. Once you have selected the report parameters, click OK to generate the report. After the report is
generated, you can select your output options in the Print dialog box.

Page Header
The Page Header is printed on each page of the Single Sample Single Attribute report, and contains
general information identifying the report. Header information includes:
· the date on which the report was generated.
· the Company Name (as entered on the Reports tab of the Options dialog box).
· the page number.
· the name of the report (Single Sample Single Attribute report).

Sample Information
This section of the Single Sample Single Attribute report lists describes the type of data included on
the report. This data is printed on every page of the report, and includes:
· Project—the name of the project associated with this job.
· Job—the job name.
· Sample—the sheet number selected for this report.

13-4
 PRINTING JOB DATA

· Mode—the computation parameters (Absolute vs. Relative and Status Density) used on this job.
· Computation—the computation type selected for this report.
· Sheet Name—the label assigned to the sheet (Makeready, Production, or Other).
· Date—the date the sheet was measured.
· Time—the time the sheet was measured.

Key Data
This section of the Single Sample Single Attribute report lists key data for the selected attribute on the
current sheet. The following data is generated for each ink of the appropriate computation/patch type:
· Key—the numbers of all keys of the selected type
· Difference—the difference between the target attribute and the sheet attribute for the selected ink.
If the different is greater than the upper limit, a “>” symbol is displayed. If the difference is less
than the lower limit, a “<” symbol is displayed. Up three different symbols may be displayed to
indicate the magnitude of the difference.
NOTE: Difference data is not displayed for density/solid report selections.
· Target—the target density value of the attribute for the selected ink.
· Value (Actual)—the actual density value of the attribute for the selected ink.

Statistics
This section of the Single Sample Single Attribute report lists statistical data for the selected attribute
on the current sheet. The following data is generated for each ink of the appropriate computation/patch
type:
· Ink Name—the name of the current ink.
· Printing Unit #—the number of the printing unit associated with this ink.
· Filter—the filter used for the selected link. This data only appears for density/solid report
selections.
· Action Limit—the action tolerance limit of the attribute for the selected ink.
· Control Limit—the control tolerance limit of the attribute for the selected ink.
· Average—the average value across all keys.
· Maximum—the maximum value across all keys.
· Range—the range of values across all keys.
· Std Dev—the standard deviation of values all across all keys. This data does not appear for
density/solid report selections.
· Minimum—the minimum value across all keys.

USING THE TREND ANALYSIS REPORT

The Trend Analysis report tracks the trend of a single selected ink and patch throughout the press run.
Because of this, you must define your report parameters before the report can be generated. The
information provided in this report allows the press operator to make adjustments based on the
documented historical trends.
The Trend Analysis report is divided into five areas:

13-5
SECTION THIRTEEN

· Page Header
· Patch Information
· Statistical Information
· Data
· Graph

To generate this report:

1. From the Report menu, choose Trend Analysis. The Trend Report Options dialog box appears.
2. In the Key box, type the number of the key that you want to use on the report, or use the arrow
buttons to select the desired key number.
3. From the Computation list, select the computation type to use on the report. You can only select
computation types supported by the current job.
4. From the Patch Type list, select the patch type to use on the report. You can only select patch
types appropriate supported by the selected computation type.
5. From the Ink list, select the ink to use on the report. You can only select inks used by the selected
patch type.
6. Once you have selected the report parameters, click OK to generate the report. After the report is
generated, you can select your output options on the Print dialog box.

Page Header
The Page Header is printed on each page of the Trend Analysis report, and contains general
information identifying the report. Header information includes:
· the date on which the report was generated.
· the Company Name (as entered on the General tab of the Options dialog box).
· the page number.
· the name of the report (Trend Analysis report)

Patch Information
This area of the Trend Analysis report includes information about the specific patch being printed, as
follows:
· Project—the name of the project associated with this job.
· Computation—the computation type selected for this report.
· Key—the key number selected for this report.
· Job—the job name.
· Patch—the patch type selected for this report.
· Mode—the computation parameters (Absolute vs. Relative and Status Density) defined for this
job.
· Ink—the ink selected for this report.
· Control Limit—the control limit for the selected computation type, patch type, and ink.
Patch information is printed on every page of the report.

13-6
 PRINTING JOB DATA

Statistical Information
This area of the Trend Analysis report includes information about the current trend, as follows:
· Average—the average for all values in the trend.
· Maximum—the maximum value in the trend.
· Range—the range of values in the trend.
· Std Dev—the standard deviation of all values in the trend.
· Minimum—the minimum value in the trend
Statistical information is printed on every page of the report.

Data
This section of the Trend Analysis report includes data for the selected patch type across all sheets in
the job. The following information is provided for each sheet:
· Sample—the sheet numbers associated with the selected patch type.
· Date—the date the sheet was measured.
· Time—the time the sheet was measured.
· Type—the label assigned to the sheet (Makeready, Production, or Other)
· Target—the target value for the selected patch type and sheet.
· Value—the actual value for the selected patch type and sheet.
· Difference—the difference value for the selected patch type and sheet.

Graph
This section of the Trend Analysis report includes a trend graph of difference values for the selected
patch type across all sheets in the job. The X-axis of the graph lists the sheet numbers, and the Y-axis
lists the difference values.

STATISTICAL PROCESS CONTROL PROGRAM

The Statistical Analysis command on the Reports menu opens the Statistical Process Control
software. This software is designed to work with data generated by the ATD system.
The Statistical Process Control software takes density data from jobs and allows you to view and
evaluate the data in more complex ways than those accessible from within ATD. It calculates and
displays statistical attributes such as histograms, X-Bar graphs, and Range graphs.
For additional information about the software, refer to the Statistical Process Control Help system.

PRINT FILE UTILITY

The Print File Utility provided with ATD allows you to print report data that was previously exported
to a file, rather than sent to an actual printer. This is convenient if you want to generate reports
utilizing multiple scanning instruments and print all the reports at one centralized location. Any
software report with a *.prn extension can be printed using this function.
To open the Print File to Printer dialog box, double-click the Print File icon in the program group.

13-7
SECTION THIRTEEN

To print a report file:

1. In the File to Print box, type the file name of the report you want to print, or click Select File to
select the report file from a standard Windows Open dialog box.
NOTE: If the report file is not located in the default Report directory for ATD, you must enter the
full path of the file.
2. Select the printer you want to use. If you want to use a local printer, s elect Local Printer and then
select the appropriate printer port from the list provided. If you want to use a network printer,
select Network Printer and then type the printer path in the box provided or click Select Printer
to choose the printer location.
3. Click Print to start printing the selected report.

13-8