A L C T E L
Alcatel OmniPCX 4400
SUBSECTION 2
10/100 baseT BRMA box
Ed.01
A L C T E L
Alcatel OmniPCX 4400
Subsection 2 - 10/100 baseT BRMA box
Subsection 2 - 10/100 baseT BRMA box
SUMMARY
10/100baseT BRMA box
Hardware description...................................................................................... 2. 3
1. General .................................................................................................. 2. 3
2. Characteristics........................................................................................ 2. 3
3. Detailed view of the BRMA unit ............................................................. 2. 4
4. Installation............................................................................................. 2. 5
5. Connection ............................................................................................. 2. 6
Ed.01 Ref.3BA19919ENAA 2.1
A L C T E L
Alcatel OmniPCX 4400
Subsection 2 - 10/100 baseT BRMA box
2.2 Ref.3BA19919ENAA Ed.01
A L C T E L
Alcatel OmniPCX 4400
Subsection 2 - 10/100 baseT BRMA box 10/100baseT BRMA box
Hardware description
44A03780100A041AAEN
10/100baseT BRMA box
Hardware description
Edition: 01
1. General
The BRMA unit (also called RMA unit) is an external unit for OmniPCX 4400 PBX remote maintenance.
This unit is used with M2 and M3 cabinets.
The BRMA unit has connectors to connect consoles and modems. It contains the RMAB board (remote
maintenance board, see module RMAB board - Operation). The BRMA unit runs on 48V power.
86 mm
(3.4'')
(2U)
425 mm
(16.7'')
280mm
(11'')
References:
3BA56170AC “BRMA 10/100B-T BOX W/O RMAB”.
3BA56170UC “BRMA 10/100B-T BOX W/O RMAB”, for the USA.
2. Characteristics
All internal system voltages are TBTS or TRT classified.
Environmental operating conditions are from 5 to 45 C.
User and equipment protection against telecoms network voltages are ensured by compliance with the
test recommendations given in chapter 6.4.2 of standard CEI 950.
Ed.01 Ref.3BA19919ENAA 2.3
A L C T E L
Alcatel OmniPCX 4400
10/100baseT BRMA box Subsection 2 - 10/100 baseT BRMA box
Hardware description
3. Detailed view of the BRMA unit
Main CPU Standby CPU
Ethernet 10/100base T COM A and COM B ports
COM A and COM B ports
for main CPU Local console V24 port
COM C and COM D Terminal connection V24
Ethernet 10/100base T
ports in "or wired" mode port (eg: modem)
for standby CPU
Terminal connection V24
Front view port (eg: TA)
E1
BRMA
Connecting Box
10Base-T/100Base-TX
E0 A0 B0 C D A1 B1 ExA ExB ExC
Rear view
48V DC 2A
PWR
ONL
RMAB
debug
Reset
EXT
CPU
ACT
INT
uP
To -48V To -48V
Fuse
(RMAB board slot)
Top view (with cover removed)
2.4 Ref.3BA19919ENAA Ed.01
A L C T E L
Alcatel OmniPCX 4400
Subsection 2 - 10/100 baseT BRMA box 10/100baseT BRMA box
Hardware description
The unit is composed of the following parts:
- on the front panel: user (Ethernet, V24, modem) connectors.
- on the rear panel: LEDs, debug connector and a feedthrough for the different cables.
- internally, the unit is divided into two zones separated by a central divider. One zone is for the
PRMA board (see: module PRMA board - Configuration) and the other for the cables and 48V
filter. The central divider protects the cables from electromagnetic radiation.
4. Installation
The BRMA unit is installed:
- on a shelf,
- wall-mounted.
Figure 1 : Drilling template for wall-mounting
200mm (7.8'')
260 mm (10.2'')
Ed.01 Ref.3BA19919ENAA 2.5
A L C T E L
Alcatel OmniPCX 4400
10/100baseT BRMA box Subsection 2 - 10/100 baseT BRMA box
Hardware description
5. Connection
To connect the cables, the BRMA unit must be opened by removing the attachment screws as follows:
Attachment screws
Protective cover
Cable attachment
plate
RMAB board
The cables must be attached to the plate with a clamp.
5.1. Power supply connection
The BRMA unit is supplied (48V) either by the PBX or by an external source of power.
5.1.1. Power supply from an M3 cabinet
Yellow/Green 4
3
Yellow/Green 2
1
4
Brown Brown 3 0V48
2
1
-48V
filter -48V
Blue 5
Blue Fuse (F1) 4
3
2
BRMA unit 1
M3 cabinet terminal block
Fuse F1: 2 A, quick-response.
2.6 Ref.3BA19919ENAA Ed.01
A L C T E L
Alcatel OmniPCX 4400
Subsection 2 - 10/100 baseT BRMA box 10/100baseT BRMA box
Hardware description
5.1.2. Power supply from an M2 cabinet
Yellow/Green
Yellow/
Green 2
Brown 1 0V48
Brown
Blue -48V
-48V 2 F2
filter F1
1
Blue Fuse (F1)
M2 cabinet terminal block
BRMA unit
Fuse F1: 2 A, quick-response.
5.2. PBX connection
Connection between the M2 (or M3) cabinet and the BRMA unit is described in module M2/M3 cabinet
- Connexion - Internal connections.
Ed.01 Ref.3BA19919ENAA 2.7
