PODIUM KP3 SECTION 2 - SET-UP & OPERATIONS

Play Table Setup-Play Lines Denomination Setup

DENOMINATION SETUP
The PLAY LINES - 20 [1 3 5 10 20] is set to 20 [20 20 20 20 20].
Use the same procedure as 20 [1 3 5 10 20] for setting other values ITEM DESCRIPTION
for PLAYLINES and MAX BET. DEFAULT Sets the current game denomination as a default when
DENOMINATION Attract mode is started.
COIN/TOKEN The value for coin/token denomination that the machine
Setting Denomination Setup DENOMINATION accepts and/or the hopper distributes.
ACCOUNTING The accounting denomination for the machine to report
DENOMINATION accounting meters to the host.
PROGRESSIVE Enable the progressive wins when using this denomi-
DENOMINATION nation.

To set the DEFAULT DENOMINATION - $0.01 to $0.02, press

the $0.01 field to show the pull down menu, and then press the $0.02
to make the selection enabled. The following screen is displayed.

Denomination Setup-Default Denomination

The displayed menus can be accessed by pressing the buttons

on the touchscreen. The Previous Item button moves the cursor to the
previous item, the Next Item button moves the cursor to the next item,
the Select Item button selects the item where the cursor is placed, the
Exit button returns to the previous menu.
Press the DENOMINATION SETUP button to enter the selec-
tion. The following screen is displayed.

The DEFAULT DENOMINATION - $0.01 is set to $0.02%. Use

the same procedure as DEFAULT DENOMINATION - $0.01 for setting
other value in the DEFAULT DENOMINATION field, COIN/TOKEN
DENOMINATION, ACCOUNTING DENOMINATION, PROGRESSIVE
DENOMINATION and EM-COUNTER DENOMINATION.
Press the Exit button to return to the SETUP menu, then press
the Exit button to return to the KMS menu. Press the DIAGNOSTIC
button to enter the selection. The following screen is displayed.

P/N 810061 2-45 © 2010 Konami Gaming Inc.

PODIUM KP3 SECTION 2 - SET-UP & OPERATIONS

Setting Diagnostic
DIAGNOSTIC MENU
ITEM DESCRIPTION
Displays information on the storage devices and Com-
MACHINE ID
pact Flash Card memory.

The displayed menus can be accessed by pressing the buttons

on the touchscreen The Previous Item button moves the cursor to the
previous item, the Next Item button moves the cursor to the next item,
the Select Item button selects the item where the cursor is placed, the
Exit button returns to the previous menu.
Press the TOUCH PANEL button to enter the selection. The
following screen is displayed.

Diagnostic-Touch Panel

When the DIAGNOSTIC menu is highlighted, press the DI-

AGNOSTIC button to enter the selection. The following screen is
displayed.

Diagnostic Menus

Press the TOUCH TEST button to enter the selection. The

following screen is displayed.

Touch Panel-Touch Test

DIAGNOSTIC MENU
ITEM DESCRIPTION
TOUCH PANEL Checks the operations for the touch screen.
BUTTON Checks the operations for the buttons.
DOOR Checks the operations for the door.
Checks the operations for Signal Tower Lights and the
OUT PORT
bill entry lamps.
COIN ACCEPTOR Checks the operations for Coin Acceptor.
COIN HOPPER Checks the operations for Coin Hopper.
HARDWARE
Checks the operations for Thermometer.
MONITOR
BILL ACCEPTOR Checks the operations for Bill Acceptor.
Draw with your finger to check the operation of the touch screen.
PRINTER Checks the operations for Printer.
This screen allows checking the coordinate adjustment of the touch
SOUND Plays the various sounds available. screen. A line will be displayed when you move your finger against
SCREEN Checks the operations on the display. the screen. Once you draw on the touch panel, the following screen
COMMUNICATION Displays information on the communications. is displayed, for example.
Displays the game test, denomination test, and RNG
GAME
test.

P/N 810061 2-46 © 2010 Konami Gaming Inc.

PODIUM KP3 SECTION 2 - SET-UP & OPERATIONS

Touch Panel-Touch Test (touch panel test) Touch Panel-Calibration (complete)

To return to the previous menu, press the Exit button or double- If any error listed, remove the error first, and then press the
tap the screen. Press the CALIBRATION button to enter the selection. RESET button to reset the error conditions.
The following screen is displayed for a few seconds. Press the Exit button to return to the DIAGNOSTIC menu. The
following screen is displayed.
Touch Panel-Calibration
Setting Diagnostic-Button

After the following screen is displayed, the calibration starts. If

pressing the Exit button, or if leaving the screen as it is for more than The displayed menus can be accessed by pressing the buttons
20 seconds, the calibration will be canceled. on the touchscreen. The Previous Item button moves the cursor to the
previous item, the Next Item button moves the cursor to the next item,
Touch Panel-touch panel test the Select Item button selects the item where the cursor is placed, the
Exit button returns to the previous menu.
Press the BUTTON button to enter the selection. The following
screen is displayed.

Touch the green circle area on the touch panel for a couple of
times following the instruction. Once the calibration is completed, the
following screen is displayed.

P/N 810061 2-47 © 2010 Konami Gaming Inc.

PODIUM KP3 SECTION 2 - SET-UP & OPERATIONS

Diagnostic-Button Diagnostic Door

The screen is for checking the button operations. If any door The screen is for checking the door switches and sensors. If
is opened, the switch toggles “ON” and “OFF”. any door is opened, the switch toggles “ON” and “OFF”.
Pressing both of the Exit buttons returns to the DIAGNOSTIC Pressing the Exit button returns to the DIAGNOSTIC menu.
menu. The following screen is displayed. Press the OUT PORT field to enter the selection. The following screen
is displayed.

Setting Diagnostic-Door Setting Diagnostic-Out Port

The displayed menus can be accessed by pressing the buttons The displayed menus can be accessed by pressing the buttons
on the touchscreen. The Previous Item button moves the cursor to the on the touchscreen. The Previous Item button moves the cursor to the
previous item, the Next Item button moves the cursor to the next item, previous item, the Next Item button moves the cursor to the next item,
the Select Item button selects the item where the cursor is placed, the the Select Item button selects the item where the cursor is placed, the
Exit button returns to the previous menu. Exit button returns to the previous menu.
Press the DOOR button to enter the selection. The following Press the OUT PORT button to enter the selection. The follow-
screen is displayed. ing screen is displayed.

P/N 810061 2-48 © 2010 Konami Gaming Inc.

PODIUM KP3 SECTION 2 - SET-UP & OPERATIONS

Diagnostic-Out Port Setting Diagnostic-Coin Acceptor

The screen is for checking the TOWER LAMP and the BILL The displayed menus can be accessed by pressing the buttons
LAMP operations. on the touchscreen. The Previous Item button moves the cursor to the
To set the TOWER LAMP 2 to enable, press the TOWER LAMP previous item, the Next Item button moves the cursor to the next item,
2 field to make the item checked. The following screen is displayed. the Select Item button selects the item where the cursor is placed, the
Exit button returns to the previous menu.
Press the COIN ACCEPTOR menu. The following screen is
Out Port-Tower Lamp 2 displayed

Diagnostic-Coin Acceptor

The TOWER LAMP 2 is set to enabled. Use the same proce-

dure as TOWER LAMP 2 for setting other TOWER LAMP options
and BILL LAMP. The screen is for checking the COIN COMPARATOR and the
Press the Exit button to return to the DIAGNOSTIC menu. The COIN DIVERTER operations.
following screen is displayed. To set the ACCEPTANCE to enable, press the ACCEPTANCE
button to make the item checked. The following screen is displayed.

P/N 810061 2-49 © 2010 Konami Gaming Inc.

PODIUM KP3 SECTION 2 - SET-UP & OPERATIONS

Coin Acceptor-Acceptance Setting Diagnostic-Coin Hopper

To set TO DROP to TO HOPPER in the DIVERTER field, press The displayed menus can be accessed by pressing the buttons
the TO HOPPER field to make the selection enabled. The following on the touchscreen. The Previous Item button moves the cursor to the
screen is displayed. previous item, the Next Item button moves the cursor to the next item,
the Select Item button selects the item where the cursor is placed, the
Exit button returns to the previous menu.
Press the COIN HOPPER button to enter the selection. The
following screen is displayed.

Coin Acceptor-Diverter
Diagnostic-Coin Hopper

If any error listed, remove the error first, and then press the
RESET button to reset the error conditions.
Press the Exit button to return to the DIAGNOSTIC menu. The screen is for checking the Coin Hopper operations.
Press the COIN HOPPER menu. The following screen is displayed. To change the value for COIN PAY - 1 to COIN PAY - 2, press
the COIN PAY field to open the pull down menu, and press "2" to
enter the selection.
If any error listed, remove the error first, and then press the
RESET button to reset the error conditions.
Press the Exit button to return to the DIAGNOSTIC menu. The
following screen is displayed.

P/N 810061 2-50 © 2010 Konami Gaming Inc.

PODIUM KP3 SECTION 2 - SET-UP & OPERATIONS

Setting Diagnostic-Hardware Monitor Hardware Monitor-Terperature Threshold

The TEMPERATURE THRESHOLD is changed to "56ºC/132ºF".

The displayed menus can be accessed by pressing the buttons Press the Exit button to return to the DIAGNOSTIC menu. The
on the touchscreen. The Previous Item button moves the cursor to the following screen is displayed.
previous item, the Next Item button moves the cursor to the next item,
the Select Item button selects the item where the cursor is placed, the
Exit button returns to the previous menu.
Press the HARDWARE MONITOR button to enter the selection.
The following screen is displayed.
Setting Diagnostic-Bill Acceptor

Diagnostic-Hardware Monitor

The displayed menus can be accessed by pressing the buttons

on the touchscreen. The Previous Item button moves the cursor to the
The screen is for checking the temperature of SYSTEM MOD- previous item, the Next Item button moves the cursor to the next item,
ULE and GAME MODULE. the Select Item button selects the item where the cursor is placed, the
To set the TEMPERATURE THRESHOULD - 55ºC/131ºF to Exit button returns to the previous menu.
56ºC/132ºF, press the TEMPERATURE THRESHOULD field to open Press the BILL ACCEPTOR button to enter the selection. The
the pull down menu, and then press "56ºC/132ºF" field. The following following screen is displayed.
screen is displayed.

P/N 810061 2-51 © 2010 Konami Gaming Inc.

PODIUM KP3 SECTION 2 - SET-UP & OPERATIONS

Diagnostic-Bill Acceptor Setting Diagnostic-Printer

The screen is for checking the BILL ACCEPTOR operations. The displayed menus can be accessed by pressing the buttons
To set the ACCEPTANCE to enable, press the ACCEPTANCE on the touchscreen. The Previous Item button moves the cursor to the
field to make the item checked. The following screen is displayed. previous item, the Next Item button moves the cursor to the next item,
the Select Item button selects the item where the cursor is placed, the
Exit button returns to the previous menu.
Press the PRINTER button to enter the selection. The following
screen is displayed.

Bill Acceptor-Acceptance Diagnostic-Printer

The ACCEPTANCE is changed to enable.

Press the Exit button to return to the DIAGNOSTIC menu. The The screen is for checking the PRINTER status.
following screen is displayed. If any error listed, remove the error first, and then press the
RESET button to reset the error conditions.
To print out a void ticket for testing, press the TEST PRINT
button.
Press the Exit button to return to the DIAGNOSTIC menu. The
following screen is displayed.

P/N 810061 2-52 © 2010 Konami Gaming Inc.

PODIUM KP3 SECTION 2 - SET-UP & OPERATIONS

Setting Diagnostic-Sound Sound-Sound volume was changed

The displayed menus can be accessed by pressing the buttons Press the Save button to accept the settings, or press the
on the touchscreen. The Previous Item button moves the cursor to the Cancel button to exit without saving it.
previous item, the Next Item button moves the cursor to the next item, If the MASTER VOLUME is not changed in the DIAGNOSTIC
the Select Item button selects the item where the cursor is placed, the SOUND screen, press the Exit button to return to the DIAGNOSTIC
Exit button returns to the previous menu. menu. The following screen is displayed.
Press the SOUND button to enter the selection. The following
screen is displayed. Setting Diagnostic-Screen

Diagnostic-Sound

The displayed menus can be accessed by pressing the buttons

on the touchscreen. The Previous Item button moves the cursor to the
The screen is for checking the Sound operations. The Previous previous item, the Next Item button moves the cursor to the next item,
Item button moves the cursor to the previous item, the Next Item button the Select Item button selects the item where the cursor is placed, the
moves the cursor to the next item, the Select Item button selects the Exit button returns to the previous menu.
item where the cursor is placed, the Exit button returns to the previous Press the SCREEN button to enter the selection. The following
menu. The DEC/INC button decrements/increments the selection for screen is displayed.
SEQUENCE DATA, the Play button plays the sound, and the Stop
button stops playing the sound.
To set the value for MASTER VOLUME - 1 to MASTER VOL-
UME - 2, press the MASTER VOLUME field to open the pull down
menu, and press "2" to enter the selection. When the MASTER
VOLUME is changed, the message prompt shown below is displayed
to save it or not.

P/N 810061 2-53 © 2010 Konami Gaming Inc.

PODIUM KP3 SECTION 2 - SET-UP & OPERATIONS

Diagnostic-Screen Diagnostic-Communication

The test pattern on the screen is for checking the SCREEN op- The screen is for checking the COMMUNICATION status. The
erations. Pressing any part on the screen returns to the DIAGNOSTIC conditions for CH1 to CH3 are shown in the table.
menu. After checking the screen and then pressing a certain part on Press the Exit button to return to the DIAGNOSTIC menu. The
the screen, the following screen is displayed. following screen is displayed.

Setting Diagnostic-Game
Setting Diagnostic-Communication

The displayed menus can be accessed by pressing the buttons

The displayed menus can be accessed by pressing the buttons on the touchscreen. The Previous Item button moves the cursor to the
on the touchscreen. The Previous Item button moves the cursor to the previous item, the Next Item button moves the cursor to the next item,
previous item, the Next Item button moves the cursor to the next item, the Select Item button selects the item where the cursor is placed, the
the Select Item button selects the item where the cursor is placed, the Exit button returns to the previous menu.
Exit button returns to the previous menu. Press the GAME button to enter the selection. The following
Press the COMMUNICATION button to enter the selection. The screen is displayed.
following screen is displayed.

P/N 810061 2-54 © 2010 Konami Gaming Inc.

PODIUM KP3 SECTION 2 - SET-UP & OPERATIONS

Setting Game-African Diamond Setting Game-RNG Test Mode

Press the African Diamond button to enter the selection. The Press the RNG TEST MODE button to enter the selection. The
following screen is displayed. following screen is displayed.

Game-RNG Test Mode

Game-African Diamond

The screen is for checking a RNG test program picking and

sending the five virtual stop positions. Perform the RNG TEST ac-
The screen is for checking the combinations in African Diamond.
cording to the instructions written on the screen.
To test the combination, press the Reels on the screen. Some option
Press the Exit button to return to the GAME menu, and then
buttons colored in Gray are also available for the test.
press the Exit button to return to the DIAGNOSTIC menu. The fol-
Press the Exit button to return to the GAME menu. The follow-
lowing screen is displayed.
ing screen is displayed.

P/N 810061 2-55 © 2010 Konami Gaming Inc.

PODIUM KP3 SECTION 2 - SET-UP & OPERATIONS

Setting Diagnostic-Machine ID Setting Out of Service

The displayed menus can be accessed by pressing the buttons The displayed menus can be accessed by pressing the buttons
on the touchscreen. The Previous Item button moves the cursor to the on the touchscreen. The Previous Item button moves the cursor to the
previous item, the Next Item button moves the cursor to the next item, previous item, the Next Item button moves the cursor to the next item,
the Select Item button selects the item where the cursor is placed, the the Select Item button selects the item where the cursor is placed, the
Exit button returns to the previous menu. Exit button returns to the previous menu.
Press the MACHINE ID button to enter the selection. The fol- Press the OUT OF SERVICE button to enter the selection. The
lowing screen is displayed. following screen is displayed.

Diagnostic-Machine ID Out Of Service

The OUT OF SERVICE message is displayed, and the machine

This screen is for checking the SYSTEM MACHINE ID and
is locked. Once the OUT OF SERVICE message appears on the
GAME MACHINE ID.
screen, the machine becomes out of control.
Press the Exit button to return to the DIAGNOSTIC menu.
Turn the Reset Key Switch or Audit Key Switch to exit from this
Press the Exit button again to return to the KMS menu. The following
situation, and return the machine to normal state.
screen is displayed.

P/N 810061 2-56 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

SECTION 3
Parts, Assemblies & Hardware

Overview WARNING: Power to the machine must be turned off prior

Section 3, Parts, Assemblies & Hardware, describes part re- to cleaning the inside of the machine or removing any
moval and installation and includes a parts manual. This manual is mechanical or electrical assembly. Unplug the machine.
intended for experienced maintenance personnel working on gaming
machines.
WARNING: Hazardous high voltage exists within the
cabinet even with machine power off and the power
• Removal cord unplugged! Use extreme caution when removing
Describes how to remove components from the cabinet. electrical assemblies to avoid injury. Discharge body
Note that you may need special tools depending on the static BEFORE touching PCBs to avoid damaging
type of component removed. electrostatic sensitive components. Only qualified
• Disassembly personnel should attempt servicing this machine.
Describes how to disassemble the components.
Disassemble the component removed from the cabinet Required Tools
into parts on which maintenance can be performed. Phillips Screwdriver (No. 1 and No. 2)
• Assembly Small Phillips Screwdrivers (No. 0 and No. 1)
Describes how to assemble the parts. Use caution when 4 to 13 mm Nut Driver or Ratchet Wrench
reconnecting harnesses to ensure proper operation. 4 to 13 mm Wrench Set
Incorrect assembly may cause malfunctions or failures. 22 to 24 mm Double-end Wrench
Hand Riveter
• Installation
Needle Nose Pliers
Describes how to install the components in the cabinet. Pliers
Voltage and Amperage Tester
CAUTION: Konami Gaming, Inc. cannot be held liable for Crimping Tool for Connectors
damages or injuries caused by improper or unsupervised Plastic Ties
installation, modification, or use of equipment not Wire Stripper
manufactured or approved by Konami Gaming, Inc. This Pin Extractor
equipment is designed as a gaming device for amusement Mounting Tool for Play Buttons (Star Point)
only, for sale and use in jurisdictions permitting such IC Extractor
devices. Distributors, Operators, and Users are not Wire Cutters
to modify the equipment for any other use. Konami
Gaming, Inc. cannot be held liable for damages or injuries
resulting from use or modification of this equipment.

CAUTION: PCB’s may contain a lithium battery.

Danger of explosion if the battery is incorrectly
replaced. Replace only with the same, or
equivalent type recommended by the manufacturer.

P/N 810061 3-1 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

Commonly-Used Hardware Functional Overview

The following table shows the hardware that this electronic This chapter describes names and functions of the main parts.
gaming machine uses. Using incorrect hardware may damage the Use the illustrations below to identify the major components.
equipment.
Hardware Employed: TOWER
LIGHT
COMMONLY USED HARDWARE
PART NUMBER DESCRIPTION
450015 NUT, HEX KEP #6-32
450016 NUT, HEX, KEP #8-32
450044 SCREW, FLAT HEAD, #4-40x1/4
HARDMETERS
450051 SCREW, FLAT HEAD, #6-32x3/8 CONVENIENCE
SHELF
450104 SCREW, SEMS, PAN HEAD PHILLIPS, #4-40x3/4
(OPTIONAL)
450107 SCREW, SEMS, PAN HEAD PHILLIPS, #4-40x1/4
TICKET LED EDGE
450109 SCREW, SEMS, PAN HEAD PHILLIPS, #6-32x1/2
CHUTE LIGHT PANELS
450110 SCREW, SEMS, PAN HEAD PHILLIPS, #6-32x1/4
AUDIT/RESET
450115 SCREW, SEMS, PAN HEAD PHILLIPS, #8-32x1/4 KEYSWITCH
BELLY DOOR
450117 SCREW, SEMS, PAN HEAD PHILLIPS, #8-32x3/8 LOGO
450121 SCREW, SEMS, PAN HEAD PHILLIPS, M3x5 MAIN DOOR
LOCK
450122 SCREW, SEMS, PAN HEAD PHILLIPS, M3x6
450123 SCREW, SEMS, PAN HEAD PHILLIPS, M3x8 SERIAL
COIN/
PLATE
450127 SCREW, SEMS, PAN HEAD PHILLIPS, M46 TOKEN ENTRY
450144 NUT, NYLOK, #2-56 BILL
ENTRY
450146 GUIDE, PCB, 6” BUTTON
PANEL COIN TRAY BELLY
450161 SCREW, CONNECTOR MOUNTING
DOOR
450163 RIVET, POP, 1/8 DIA x 3/8 LONG LOCK
450166 E-RING, .343 IDx.039 GROOVE
450167 SCREW, PAN HEAD PHILLIPS, M3x12
450176 WASHER, #8 FLAT
450185 STAY, DOOR, 10.5” LED LIGHT
PANEL
450282 NUT, HEX, NYLOCK, #8-32 (OPTIONAL)
450285 WASHER, FENDER, #10, OD 1x7/32, ID 3/64
450366 NUT, HEX, #2-56 SUB-WOORER
450420 SCREW, TPG, HEX WSHR HD, #4-40x.250 (BEHIND LCD)

450428 SCREW, TPG, HEX WSHR HD, #8-32x.250

LCD w/TOUCH
450430 SCREW, TPG, HEX WSHR HD, #8-32x.375
SCREEN
450431 SCREW, TPG, HEX WSHR HD, #8-32x.500
PLAYER
450433 SCREW, HEMS, PAN HEAD PHILLIPS, #10-32x3/8 TRACKING
PANEL

SPEAKERS

BILL VALIDATOR
ACESS DOOR

PRINTER
POWER SUPPLY
LOGIC
COIN UNIT MAIN POWER
MECHANISM HOUSING HOPPER
SWITCH

P/N 810061 3-2 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

Parts Removal Belly Door Switch

Describes how to remove components from the cabinet. Removal
Note: Special tools may be needed depending upon the type of Open the Main
component being removed. Turn off the game power before servicing d o o r. R e m o v e t h e
components inside the game. power supply, if neces-
sary, for better access
to the switch terminals.
Parts Installation
Remove all wires from
Describes how to install components into the cabinet.
the back of the switch.
Note wire locations for
Main Door Switch future reference during
Removal
installation. Gently grasp
Open the Main door.
the Main door switch
Remove the power supply, if
from the top and bottom
necessary, for better access
behind the mounting
to switch terminals. Remove
bracket and push the switch forward.
all wires from the back of the
switch. Note wire locations for
Installation
future reference during instal-
Insert the switch from the front of the machine. Gently push the
lation. Gently grasp the Main
switch into the bracket until it seats. Connect the wires to the terminals.
door switch from the top and
Turn on machine power. Close and lock the Main door.
bottom behind the mounting
bracket and push the switch
forward. Switch Wiring
Each wire of the switch harnesses is marked to indicate terminal
position. Use the illustration below to ensure the switch is connected
Installation
correctly.
Insert the switch from the front of the machine. Gently push the
switch into the bracket until it seats. Connect the wires to the terminals.
Turn on machine power. Close and lock the Main door. DOOR SWITCH WIRE LOCATIONS
LOCATION MARK
Top Box Door Switch Terminal 2 COM
(Removal and Installation is the same for all three (3) top Terminal 4 N.C.
boxes). Terminal 6 N.O.
Removal
Open the top box door and remove the LCD or other compo-
nents to allow access to the switch. Remove the connectors from the
switch noting the location for installation. Remove the two (2) #8-32
nuts securing the switch mounting bracket to the top box. Grasp the
two tabs on the switch and push forward to remove the bracket.

Installation
Push the new switch into
the mounting bracket until the
two tabs on the switch seat in 2 6 5 1
place. Place the connectors on 4 3

the switch in the proper loca-

tions. Mount the bracket onto
the top box with the two (2)
#8-32 nuts. Re-install the LCD COM1 NC1 COM2
or other components removed (1-C) NO1
(1-NC) (1-NO)
NO2 NC2 (2-C)
(2-NO) (2-NC)
to allow access to the switch.

P/N 810061 3-3 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE
from the back of the bill validator. Remove the bill validator.
Hopper
Removal Installation
Open the Main door. Grasp the hopper by the handle and Install the bill validator. Insert the four (4) #6-32x1/4 screws
slide forward. into the back of the bill validator. Insert the three (3) #M4x4 screws
into the left side of the enclosure. Install the cash cassette box by
depressing the cash box latch and sliding the box to the back of the
bill validator housing. Close and lock the bill cassette door. Close and
lock the Main door.

Logic Unit
Removal
Tu r n o f f
machine power.
Open the Main
Installation door. Remove
Align the hopper into the two hopper guides. Firmly insert the the Logic Unit
hopper making sure the hopper plug is fully connected to the power door. Set aside.
control panel connector. Unplug all con-
nectors from the
Logic Unit. Use a
Power Supply
Removal long screwdriver
Open the to remove the #6-
Main door. Loosen 32 security screw.
the power supply Remove the logic
mounting screw lo- unit by sliding it
cated in the lower forward until it clears the mounting rails. Remove the Logic Unit.
right-hand corner of
the fallplate. Slide Installation
the power supply as- Insert Logic Unit and slide it back until supported by the mount-
sembly forward until ing rails. Use a long screwdriver to tighten the #6-32 security screw.
it clears the mount- Connect all harnesses. Install and lock the logic unit door. Turn on
ing rails. Main power. Close and lock the Main door.

CAUTION: PCBs are electrostatic sensitive!

Installation
Discharge body static prior to handling any PCB to prevent
Slide the
damage or destruction of static sensitive components.
power supply into
the mounting rails
and push back until the power supply connector is securely seated. Main Processing Unit
Tighten the mounting screws. Removal
Place the Logic Unit on a clean, stable surface. Gently pull the
Bill Validator PCB latches toward you and pull the Main Processing Unit (MPU)
Removal board forward.
Open the
Main door. Open the Installation
bill cassette door. Align
Remove the cash the MPU board
cassette box by de- on the guides.
pressing the cash Slide back
box latch and slid- until the con-
ing the box forward. nectors are
Remove the three firmly seated.
(3) #M4x4 screws Snap the PCB
from the left side of latches forward
the enclosure. Re- until they con-
move the four (4) tact the edge
#6-32x1/4 screws of the board.

P/N 810061 3-4 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE
Backplane Board
Removal Printer Assembly
Remove the Removal
MPU board. Discon- Turn off
nect the harness machine power.
connected to the Open the Main
backplane board. door. Disconnect
Remove the ten the harnesses
(10) #6-32 screws from the printer
from the backplane assembly. Re-
board. Remove the move the four
backplane board. (4) screws se-
curing the printer
Installation to the mounting
Place the bracket.
backplane board
in position. Install Installation
the ten (10) #6-32 Install the
screws in the backplane board. Connect the harnesses. Install the four (4) screws securing the printer to the mounting bracket. Con-
MPU board. nect the harness to the printer assembly. Close the Main door. Turn
on main power.
NOTE: Each #6-32 screw secures a grounded
connection between the backplane board and the Belly Glass
game. All screws are required for proper operation. Removal
Open the
Logic Unit Switch Main door. Turn
Removal off machine pow-
Dis- er. Open the belly
connect the door. Disconnect
harness from the harnesses
the switch. Re- from the belly light
move the two assembly.
(2) #2-56 nuts
from the switch Installation
a s s e m b l y. Install the
Remove the belly glass. Install the belly artwork. Install the belly light assembly.
switch. Install the two (2) nuts. Connect the harnesses to the belly light
assembly. Close the belly door. Turn on machine power. Close the
Installation Main door.
Locate the switch on mounting studs. Install the two (2) #2-56
nuts. Connect the harness.

Key Switch
Removal
Turn off machine
power. Open the Main
door. Disconnect the
wires on the back of the
switches. Remove the
3/4” nut.

Installation
Insert the switch.
Install the 3/4” nut. Con-
nect the wires to the termi-
nals. Turn on main power.
Lock the Main door.

P/N 810061 3-5 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

Power Distribution Assembly LCD Unit

Removal (Removal and Installation is the same for Main and Top Box LCD)
Open the Main door of the cabinet and turn off the main power Removal
supply. Remove the hopper, if equipped, to gain access to the power Open the display door and loosen the set screws on each side
distribution assembly. Remove all the connectors from the assembly of the LCD assembly. Rotate the LCD forward enough to allow ac-
noting their location for installation. Remove the four (4) #8-32 nuts cess to the LCD connector. Remove the LCD connectors and safety
securing the assembly to the main cabinet. lanyards from the assembly. Lift the LCD assembly pivot pins out of
the mounting groove to remove.

Installation
Place the power distribution assembly on the four (4) mounting
studs inside the main cabinet and secure in place with #8-32 nuts.
Install all the necessary connectors to the assembly. Install the hop- Installation
per, if equipped. Turn on the main power supply and close and lock Tilt the LCD assembly slightly forward and place pivot pins into
the Main door. mounting grooves. While holding the LCD in place, install the con-
nectors and safety lanyards to the assembly. Rotate the LCD in place
Bill Validator Switch Assembly making sure the locating pins align with mounting holes. Tighten LCD
Removal assembly set screws, close and lock display door.
Open the Main door. Turn off machine power. Remove the
hopper. Remove the bill validator. Disconnect the harness from the Speakers
bill validator door switch assembly. Remove the two (2) #8-32 nuts. Removal
Remove the bill validator door switch assembly. Open the system enclosure door and remove the screws
securing the speakers to the mounting brackets. Pull the speakers
out enough to gain access to the mounting connectors and remove.
Remove the speakers.

Installation
Place the connectors on the speakers in the correct locations
and place speaker into mounting bracket. Secure in place with screws.
Installation
Install bill validator door switch assembly. Install the two (2)
#8-32 nuts. Connect the harnesses to the bill validator door switch
assembly. Install the bill validator. Install the hopper. Turn on machine
power. Close the Main door.

P/N 810061 3-6 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

Meter Assembly
Removal
Open the Main display door and remove the LCD assembly
to gain access to the meter assembly. Disconnect the harness from
the meter assembly. Remove the four (4) #8-32 screws securing the
meter assembly to the enclosure.

Installation
Place the plex face on the face of the meter assembly and
mount to the four (4) mounting studs inside the enclosure. Secure
in place with four (4) #8-32 nuts. Install the connector on the meter
assembly. Re-install the LCD assembly, close and lock the Main
display door.

P/N 810061 3-7 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

MAIN MACHINE ASSY - EXT TOP BOX w/ LCD or LED LT PANEL, SHELF and NON-SHELF VERSIONS
ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION
1. 630004 TOWER, TWO-TIER, TALL (OPTIONAL) 330953 ASSY, CABINET, MAIN (shelf)
2. 450115 SCREW, SEMS, PH PHIL, #8-32x1/4 (2) 8. or
330710 ASSY, EXT TOP BOX w/LCD 330954 ASSY, CABINET, MAIN (non-shelf)
3 or 9. 330732 ASSY, DOOR, MAIN
330715 ASSY, EXT TOP BOX w/LED LT PNL 10. 450016 NUT, HEX KEP, #8-32 (4)
4. 450104 SCREW, SEMS, PH PHIL, #10-32x3/4 (12) 11. 330709 ASSY, ENCL, LWR, LCD
5. 310294 ASSY, PNL, LT, SANDWICH (2)
330730 ASSY, ENCLOSURE, SYSTEM (shelf)
6. or
330832 ASSY, ENCLSOURE, SYSTEM (non-shelf)
7. 450433 SCREW, SEMS, PH PHIL, #10-32x3/8 (6)

1 2

3 4

4 11

6 7

9 10

P/N 810061 3-8 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

MAIN MACHINE ASSY - TBSTN TOP BOX w/ LCD or LED LT PNL, SHELF and NON-SHELF VERSIONS
ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION
1. 630004 TOWER, TWO-TIER, TALL (REF) 330953 ASSY, CABINET, MAIN (shelf)
2. 450115 SCREW, SEMS, PH PHIL, #8-32x1/4 (2) 8. or
330733 ASSY, TBSTN TOP BOX w/LCD 330954 ASSY, CABINET, MAIN (non-shelf)
3. or 9. 330732 ASSY, DOOR, MAIN
330753 ASSY, TBSTN TOP BOX w/LED LT PNL
10. 450016 NUT, HEX KEP, #8-32 (4)
4. 450104 SCREW, SEMS, PH PHIL, #10-32x3/4 (12) 11. 330709 ASSY, ENCLOSURE, LOWER, LCD
5. 310294 ASSY, PANLE, LT, SANDWICH (2)
330730 ASSY, ENCLOSURE, SYSTEM (shelf)
6. or
330832 ASSY, ENCLOSURE, SYSTEM (non-shelf)
7. 450433 SCREW, SEMS, PH PHIL, #10-32x3/8 (6)

1 2

3 4

4 11

6 7

9 10

P/N 810061 3-9 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

MAIN MACHINE ASSY - SHORT TOP BOX w/ LED LT PNL, SHELF and NON-SHELF VERSION

ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION

1. 630004 TWR, TWO-TIER, TALL (REF) 330953 ASSY, CABINET, MAIN (shelf)
2. 450115 SCREW, SEMS, PH PHIL, #8-32x1/4 (2) 8 or
3 330787 ASSY, SHORT TB, LT PNL 330954 ASSY, CABINET, MAIN (non-shelf)
4. 450104 SCREW, SEMS, PH PHIL, #10-32x3/4 (12) 9. 450016 NUT, HEX KEP, #8-32 (4)
5. 310294 ASSY, PNL, SANDWICH (2) 10. 330732 ASSY, MAIN DOOR
330730 ASSY, ENCLOSURE, SYSTEM (shelf) 11. 330709 ASSY, BOX, LOWER, LCD
6. or
330832 ASSY, ENCLOSURE, SYSTEM (non-shelf)
7. 450433 SCREW, SEMS, PH PHIL, #10-32x3/8 (6)

1 2

3 4

4 11
5

6 7

9 10

P/N 810061 3-10 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

NON-SHELF OPTION:
ALL TOP BOX CONFIGURATIONS
SYSTEM ENCLOSURE WILL WORK WITH
P/N 330832 REPLACES THIS OPTION.
330730 FOR NON-
SHELF VERSION

MAIN CABINET
P/N 330954 REPLACES
330953 FOR NON-
SHELF VERSION

P/N 810061 3-11 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

P/N 330953 ASSY, MAIN CABINET (SHELF)

ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION

1. 110418 HRNS, K3-URV, MAIN 29. 410019 TUBE, DROP
2. 110426 HRNS, K3-URV, HOPPER 30. 410255 LINER, SHELF TRAY
3. 130057 PLUG, RESET KEY 31. 450015 NUT, HEX, KEP, #6-32 (5)
4. 130590 ASSY, WELD, MAIN CAB 32. 450016 NUT, HEX, KEP, #8-32 (36)
5. 130593 ASSY, WELD, LOCK BAR, MAIN CAB 33. 450107 SCREW, SEMS, PH PHIL, #4-40 X 1/4 (4)
6. 190026 GUIDE, HOPPER, LF 34. 450109 SCREW, SEMS, PH PHIL, #6-32 X 1/2 (3)
7. 190027 GUIDE, HOPPER, RT 35. 450110 SCREW, SEMS, PH PHIL, #6-32 X 1/4 (4)
8. 190070 FAN, GUARD, 3.25” MTG 36. 450115 SCREW, SEMS, PH PHIL, #8-32 X 1/4 (14)
9. 190223 HOLD, SWITCH, CBNT 37. 450127 SCREW, SEMS, PH PHIL, M4 X 6 (7)
10. 190309 BKT, MTG, SENSOR, MAIN DOOR CAM 38. 450161 SCREW, CONN MTG
11. 191543 CAM, MAIN DOOR 39. 450163 RIVET, POP, 1/8 DIA X 3/8 LONG
12. 191544 PNL, TRIM, CAB, TOP 40. 450167 SCREW, PH PHIL, M3 X 12 (2)
13. 191578 BKT, MTG, HOPPER PLUG 41. 450285 WASHER, FENDER, #10 OD X 1 7/32 ID X 3/64
14. 191617 PLT, LOUVRE 42. 470044 GASKET, LOUVRE PLT
15. 191618 TRAY, SLIDE, PS 43. 470052 SEAL, DOOR
16. 191697 PLT, SERIAL NUMBER, TUV (OPT) 44. 490044 SWITCH, CHERRY, E79-30A
17. 230004 NUT, RETAINING, LATCH BAR 45. 490065 SENSOR, PHOTO, ALEPH
18. 310025 KEYSWITCH, ROTARY, SLIDE, ASSY 46. 490078 CORD, AC, US/CANADA (OPT)
19. 310182 BV, JCM, UBA-10-SS, STD W/CASHBOX (OPT) 47. 490152 CLAMP, VINYL COATED, 2 1/2 BLACK
20. 310234 HOPPER, LP, SIDE EJECT, $0.25 (OPT) 48. 530054 FAN, LOGIC BOX, 600mm HRNS
21. 310287 ASSY, POWER SUPPLY 49. 530365 PCB, K3-SL, K3-ICON2
22. 330099 ASSY, SWITCH, BV DOOR 50. 710000 LOCK, BARREL, .625 LONG (FOR SHIPPING)
23. 330698 ASSY, HSG, BV, JCM, STD (OPT) 51. 830055 DECAL, FCC DISCLAIMER
24. 330700 ASSY, BKT, MTG, PTR (OPT) 52. 830079 DECAL, RESET/AUDIT
25. 330714 ASSY, POWER CNTRL PNL 53. K-0485 KIT, PS COOLING FAN
26. 330764 ASSY, PTR, SEIKO GEN 2 (OPT)
27. 330952 ASSY, HSGN, CPU, K3 OPT = OPTIONAL COMPONENTS
28. 410008 ENTRY, BV, I.F, JCM (OPT)

P/N 330954 ASSY, MAIN CABINET (NON-SHELF)

NOTE: This assembly is the same as P/N 330953 except replace
P/N 191544 with P/N 191707 and delete P/N 410255

P/N 810061 3-12 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

NOTE: APPLY DOOR SEAL

P/N 470052 ALONG TOP AND
RIGHT SIDE OF CABINET DOOR
FLANGE

P/N 810061 3-13 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

P/N 330732 ASSY, MAIN DOOR

ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION

1. 330728 ASSY, PNL, 15 BTN (OPT) 21. 191557 CATCH, DOOR, MAIN CAB
2. 450016 NUT, HEX, HEX #8-32 (7) 22. 450439 GROMMET, RUBBER, .50 ODx.25 TK (2)
3. 450428 SCREW, TPG, HEX WSHR HD #8-32x.250 (4) 23. 450229 BEARING, GUIDE
4. 330745 ASSY, BEZEL, BILL VALIDATOR (2) 24. 191558 BKT, ACT, DOOR SW, MAIN CAB
5. 450115 SCREW, SEMS, PH PHIL #8-32x1/4 (10) 25. 191546 TRAY, COIN (OPT)
6. 610042 DOOR, MAIN CABINET 26. 610046 CAP, END, COIN TRAY, RT (OPT)
7. 450418 CLAMP NYLON .125 ID, OFF WHITE (2) 27. 610045 CAP, END, COIN TRAY, LT (OPT)
8. 450117 SCREW, SEMS, PH PHIL #8-32x3/8 (2) 28. 450431 SCREW, TPG, HEX WSHR HD #8-32x.500 (4)
9. 610052 BACKPLATE, COIN $0.25 (OPT) 29. 330706 ASSY, DOOR, BELLY
10. 450420 SCREW, TPG, HEX WSHR HD #4-40x.250 (2) 30. 710000 LOCK, BARREL, .625 LG (FOR SHIPPING)
11. 191545 HINGE, DOOR 31. 190713 CAM, LOCK, BELLY DOOR
12. 450430 SCREW, TPG, HEX WSHR HD #8x32x.375 (24) 32. 230055 PIN, SLIDE LOCK, BELLY DOOR
13. 191556 BKT, PIVOT, BELLY DOOR (2) 33. 450166 E-RING, .3431Dx.039 GROOVE
14. 191549 BKT, MTG, COIN PANEL 34. 230001 GUIDE, PIN, SLIDE LOCK, BELLY DOOR
15. 450282 NUT, HEX, NYLON #8-32 (2) 35. 410226 CVR, BTN, SIDE (2)
16. 450185 DOOR STAY, 10.5” 36. 191047 CLAMP, BKT, BTN CVR (2)
17. 330703 ASSY, COIN PANEL (OPT) 37. 310207 BOLSTER, DOOR, MAIN CAB
18. 530000 COMPARITOR, $.05 HUC17, CM (OPT) 39. 330839 ASSY, DRAIN BEZEL, LT
19. 130597 ASSY, WELD, CHUTE, COIN EXIT 40. 330840 ASSY, DRAIN BEZEL, RT
20. 450015 NUT, HEX, KEP #6-32 (3)

NOTE: FOR COINLESS GAMES P/N 610044 REPLACES THE

COIN TRAY AND ASSOCIATED PARTS

P/N 810061 3-14 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

4
3
1
38

7
6

39
8
33

37 9

5
36 10
11
31
12
35

2 13
34

12
30

32 15
14 5 12

29

23

33
22 24 12

21 12
16

12
17

19 18
20
26 12 25

P/N 810061 3-15 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

P/N 330730 ASSY, SYSTEM ENCLOSURE

ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION
1. 310215 ASSY, BEZEL, SYSTEM W/SPKR GRILL 15. 191552 HINGE, BEZEL, SYSTEM
2. 130598 ASSY, ENCL, SYSTEM, WELD 16. 710000 LOCK, BARREL, .625 LG (FOR SHIPPING)
3. 191559 BKT, MTG, HINGE 17. 450015 NUT, HEX KEP #6-32 (4)
4. 191881 BKT, MTG, SPKR, LT 18. 450016 NUT, HEX KEP #8-32 (16)
5. 191882 BKT, MTG, SPKR, RT 19. 191564 PLATE, CAM, ENCL, SYSTEM
6. 191602 BKT, MTG, SWITCH 20. 191596 PNL, BLANK, PODIUM (OPT)
7. 191569 BKT, SUPT, CAM PLATE 21. 450110 SCREW, SEMS, PH PHIL #6-32 X 1/4 (6)
8. 450459 BUMPON, BLACK 22. 450115 SCREW, SEMS, PH PHIL #8-32 X 1/4 (2)
9. 191563 CAM, ENCL, SYSTEM 23. 450430 SCREW, TPG, HEX WSHR HD #8-32 X 3/8 (4)
10. 490152 CLAMP, VINYL COAT, 2 1/2, BLACK (2) 24. 530322 SPKR, RECT, 8 OHM, 5W (2)
11. 530054 FAN, LOGIC BOX, 600mm HRNS 25. 490044 SWITCH, CHERRY, E79-30A
12. 191070 FAN, GUARD, 3.25 MTG 26. 191635 Bkt, Mounting, Speaker (2)
13. 470048 GASKET, DOOR, LCD BEZEL N/S 110419 HRNS, K3-URV, PT UNIT
14. 470045 GASKET, TOP BOX N/S = Not Shown

P/N 810061 3-16 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

P/N 330832 ASSY, SYSTEM ENCLOSURE, NON-SHELF

ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION
1. 130653 ASSY, WELD, ENCL, SYSTEM 15. 450110 SCREW, SEMS, PH PHIL #6-32x1/4 (6)
2. 190070 FAN GUARD, 3.25 MTG 16. 450115 SCREW, SEMS, PH PHIL #8-32 X 1/4 (2)
3. 191552 HINGE, BEZEL, SYSTEM 17. 450430 SCREW, TPG, HEX WSHR HD #8-32 X 3/8 (4)
4. 191559 BKT, MTG, HINGE 18. 450439 GROMMET, RUBBER .50 OD X .25 THK (2)
5. 191563 CAM, ENCL, SYSTEM 19. 450459 BUMPON, BLACK
6. 191564 PLATE, CAM, ENCL, SYSTEM 20. 470045 GASKET, TOP BOX
7. 191569 BKT, SUPP, CAM PLATE 21. 490044 SWITCH, CHERRY, E79-30A
8. 191596 PNL, BLANK, PODIUM (OPT) 22. 490152 CLAMP, VINYL COATED, 2 1/2, BLACK (2)
9. 191602 BKT, MTG, SWITCH 23. 530054 FAN, LOGIC BOX, 600mm HRNS
10. 191705 BKT, SUPP, LT, SYSTEM 24. 530322 SPKR, RECT, 8 OHM, 5 W (2)
11. 191706 BKT, SUPP, RT, SYSTEM 25. 710000 LOCK, BARREL, .625 LG (FOR SHIPPING)
12. 310286 ASSY, BEZEL, SYSTEM W/SPKR GRILL N/S 110419 HRNS, K3-URV, PT UNIT
13. 450015 NUT, HEX, KEP #6-32 (4) N/S = Not Shown
14. 450016 NUT, HEX, KEP #8-32 (16)

P/N 810061 3-17 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

P/N 330709 ASSY, MAIN DISPLAY

ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION
1. 330707 ASSY, DOOR, LOWER DISPLAY 17. 450282 NUT, HEX, NYLOK #8-32 (4)
2. 310310 ASSY, LCD, W/TOUCH SCREEN 22” 18. 450115 SCREW, SEMS, PH PHIL #8-32x1/4 (4)
3. 310219 ASSY, WOOFER, 3” 19. 450127 SCREW, SEMS, PH PHIL, M4 X 6 (2)
4. 191573 BKT, SUPP, LCD, LT 20. 490044 SWITCH, CHERRY, E79-30A
5. 191567 BKT, SUPP, LCD, RT 21. 450176 WASHER, #8 FLAT
6. 191602 BKT, MTG, SWITCH N/S 110420 HRNS, K3-URV, MDL UNIT
7. 191563 CAM, ENCL, SYSTEM N/S 110423 HRNS, K3-URV, METER
8. 130601 CBNT, DISP, LWR, WELD N/S = NOT SHOWN
9. 490152 CLAMP, VINYL COAT, 2 1/2, BLK (4)
10. 410018 COVER,METER, CLEAR
11. 450185 DOOR, STAY, 10.5” (2)
12. 470045 GASKET, TOP BOX (2)
13. 191552 HINGE, BEZEL, SYSTEM (2)
14. 710000 LOCK, BARREL, .625 LG (FOR SHIPPING)
15. 330003 METER, 5 UNIT
16. 450016 NUT, HEX, KEP #8-32 (20)

P/N 810061 3-18 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

P/N 330710 ASSY, EXT TOP BOX w/ LCD

ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION

1. 330708 ASSY, DOOR, DISP, UPPR 16. 450016 NUT, HEX, KEP #8-32 (15)
2. 310310 ASSY, LCD, W/TOUCH SCREEN, 22” 17. 450115 SCREW, SEMS, PH PHIL #8-32 X 1/4 (4)
3. 191573 BKT, SUPT, LCD, LT 18. 450127 SCREW, SEMS, PH PHIL M4 X 6 (2)
4. 191567 BKT, SUPT, LCD, RT 19. 490044 SWITCH, CHERRY, E79-30A
5. 191602 BKT, MTG, SWITCH N/S 110421 HRNS, K3-URV, TOP UNIT
6. 191563 CAM, ENCL, SYSTEM N/S= NOT SHOWN
7. 130600 CBNT, DISP, UPPR, WELD
8. 490152 CLAMP, VINYL COAT, 2 1/2, BLK (3)
9. 450185 DOOR, STAY, 10.5” (2)
10. 530054 FAN, LOGIC BOX, 600mm HRNS
11. 190070 FAN, GUARD, 3.25” MTG
12. 470045 GASKET, TOP BOX
13. 191552 HINGE, BEZEL, SYSTEM (2)
14. 710000 LOCK, BARREL, .625 LNG (FOR SHIPPING)
15. 450015 NUT, HEX, KEP #6-32 (4)

P/N 810061 3-19 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

P/N 330715 ASSY, EXT TOP BOX w/ LED LT PNL

ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION
1. 330720 ASSY, DOOR, DISP, UPPR 12. 450016 NUT, HEX, KEP #8-32 (11)
2. 191567 BKT, SUPT, LCD, RT 13. 450113 SCREW, SEMS, PH PHIL #8-32 X 1/4 (4)
3. 191602 BKT, MTG, SWITCH 14. 490044 SWITCH, CHERRY, E79-30A
4. 191563 CAM, ENCL, SYSTEM N/S 110421 HRNS, K3-URV, TOP UNIT
5. 130600 CBNT, DISP, UPPR, WELD N/S = NOT SHOWN
6. 490152 CLAMP, VINYL COAT, 2 1/2 BLK (3)
7. 530054 FAN, LOGIC BOX, 600mm HRNS
8. 190070 FAN, GUARD, 3.25” MTG
9. 191552 HINGE, BEZEL, SYSTEM (2)
10. 710000 LOCK, BARREL, .625 LG (FOR SHIPPING)
11. 450015 NUT, HEX, KEP #6-32 (2)

P/N 810061 3-20 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

P/N 330733 ASSY, TBSTN TOP BOX w/ LCD

ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION
1. 330734 ASSY, DOOR, TBSTN TB 13. 470045 GASKET, TOP BOX
2. 310310 ASSY, LCD, W/TOUCH SCREEN, 22” 14. 191552 HINGE, BEZEL, SYSTEM (2)
3. 130604 ASSY, TBSTN TB, WELD 15. 710000 LOCK, BARREL, .625 LG (FOR SHIPPING)
4. 191621 BKT, MTG, TBSTN TB, CANDLE/TOPPER 16. 450015 NUT, HEX, KEP #6-32 (4)
5. 191573 BKT, SUPT, LCD, LT 17. 450016 NUT, HEX, KEP #8-32 (15)
6. 191567 BKT, SUPT, LCD, RT 18. 450282 NUT, HEX, NYLOK #8-32 (2)
7. 191602 BKT, MTG, SWITCH 19. 450115 SCREW, SEMS, PH PHIL #8-32 X 1/4 (4)
8. 191563 CAM, ENCL, SYSTEM 20. 450127 SCREW, SEMS, PH PHIL M4 X 6 (2)
9. 490152 CLAMP, VINYL COAT, 2 1/2, BLK (3) 21. 450044 SWITCH, CHERRY, E-79-30A
10. 450185 DOOR, STAY, 10.5” (2) N/S 110421 HRNS, K3-URV, TOP UNIT
11. 530054 FAN, LOGIC BOX, 600mm HRNS N/S = NOT SHOWN
12. 190070 FAN, GUARD, 3.25” MTG

P/N 810061 3-21 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

P/N 330753 ASSY, TBSTN TOP BOX w/ LED LT PNL

ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION
1. 330754 ASSY, DOOR, TBSTN TB, LT PNL 10. 191552 HINGE, BEZEL, SYSTEM (2)
2. 130604 ASSY, TBSTN TB, WELD 11. 710000 LOCK, BARREL, .625 LG (FOR SHIPPING)
3. 191621 BKT, MTG, TBSTN TB, CANDLE/TOPPER 12. 450015 NUT, HEX, KEP #6-32 (4)
4. 191567 BKT, SUPT, LCD, LT 13. 450016 NUT, HEX, KEP #8-32 (11)
5. 191602 BKT, MTG, SWITCH 14. 450282 NUT, HEX, NYLOK #8-32 (4)
6. 191563 CAM, ENCL, SYSTEM 15. 450115 SCREW, SEMS, PH PHIL #8-32 X 1/4 (4)
7. 490152 CLAMP, VINYL COAT, 2 1/2 BLK (3) 16. 490044 SWITCH, CHERRY, E79-30A
8. 530054 FAN, LOGIC BOX, 600mm HRNS N/S 110421 HRNS, K3-URV, TOP UNIT
9. 190070 FAN, GUARD, 3.25” MTG N/S =NOT SHOWN

P/N 810061 3-22 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

P/N 330787 ASSY, SHORT TOP BOX DOOR w/ LED LT PNL

ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION
1. 130622 ASSY, SHORT TB, WELD 11. 410235 PLEX, SHORT TB
2. 190070 FAN, GUARD, 3.25” MTG 12. 450015 NUT, HEX, KEP #6-32 (4)
3. 191522 HINGE, BEZEL, SYSTEM 13. 450016 NUT, HEX, KEP #8-32 (14)
4. 191563 CAM, ENCL, SYSTEM 14. 450115 SCREW, SEMS, PH PHIL #8-32 X 1/4 (2)
5. 191602 BKT, MTG, SWITCH 15. 450282 NUT, HEX, NYLOK #8-32
6. 191621 BKT, MTG, TBSTN TB, CANDLE/TOPPER 16. 490044 SWITCH, CHERRY, E79-30A
7. 191651 BKT, MTG, LT PNL, LT 17. 490152 CLAMP, VINYL COAT, 2 1/2 BLK (2)
8. 191652 BKT, MTG, LT PNL, RT 18. 530054 FAN, LOGIC BOX, 600mm HRNS
9. 310276 ASSY, LED LT PNL, SHORT TB 19. 710000 LOCK, BARREL, .625 LG (FOR SHIPPING)
10. 330788 ASSY, DOOR, SHORT TB, LT PNL 20. 830652 INSERT, SHORT TB (REF)
N/S 110421 HRNS, K3-URV, TOP UNIT
N/S =NOT SHOWN

2
3
1

P/N 330720 ASSY, EXT TOP BOX DOOR w/ LED LT PNL 4

ITEM PART # DESCRIPTION

5
1. 410202 BEZEL, LCD, 22”
2. 610049 DOOR, DISPLAY 6
3. 450107 SCREW, SEMS, PH PHIL #4-40x1/4 (10)
4. 191559 BKT, MTG, HINGE (2) 7
5. 410221 PLEX, TOP BOX
6. 830522 INSERT, TOP BOX (REF)
7. 191595 BKT, MTG, LIGHT PNL, LT
8. 310211 ASSY, PNL, LIGHT, TOP BOX
9. 450430 SCREW, TPG, HEX WSHR HD #8x32x.375 (8)
10. 450016 NUT, HEX, KEP #8-32 (4)
11
11. 191594 BKT, MTG LT PNL, RT

10
9
8

P/N 810061 3-23 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

P/N 330707 ASSY, MAIN DISPLAY DOOR P/N 330708 ASSY, EXT TOP BOX DOOR (w/LCD)
ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION
1. 410202 BEZEL, LCD, 22” 1. 410202 BEZEL, LCD, 22”
2. 450107 SCCREW, SEMS, PH PHIL #4-40x1/4 (10) 2. 450107 SCREW, SEMS, PH PHIL #4-40x1/4 (10)
3. 191559 BKT, MTG, HINGE (2) 3. 191559 BKT, MTG, HINGE (2)
4. 450430 SCREW, TPG, HEX WSHR HD #8-32x.375 (6) 4. 450430 SCREW, TPG, HEX WSHR HD #8-32x.375 (6)
5. 610049 DOOR, DISPLAY 5. 610049 DOOR, DISPLAY
6. 191564 PLATE, CAM, ENCL, SYSTEM 6. 191564 PLATE, CAM, ENCL, SYSTEM
7. 470048 GASKET, DOOR, LCD/BEZEL (2) 7. 470048 GASKET, DOOR, LCD/BEZEL (2)
1 2
1 2

3 4
3 4

LOCATE 5
7 6 4
AS SHOWN
7 6 4 5
LOCATE AS SHOWN

P/N 330754 ASSY, TBSTN TOP BOX DR w/ LED LT PNL P/N 330734 ASSY, TBSTN TB DOOR (w/LCD)
ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION
1. 410209 BEZEL, TBSTN TB 1. 410209 BEZEL, TBSTN TB
2. 450107 SCREW, SEMS, PH PHIL #4-40x1/4 (10) 2. 450107 SCREW, SEMS, PH PHIL #4-40x1/4 (10)
3. 610050 DOOR, TBSTN TB 3. 450430 SCREW, PTG, HEX WSHR HD #8-32x.375 (6)
4. 191634 BKT, MTG, LT PNL, LT 4. 191559 BKT, MTG, HINGE (2)
5. 450430 SCREW, PTG, HEX WSHR HD #8-32x.375 (6) 5. 610050 DOOR, TBSTN TB
6. 450016 NUT, HEX, KEP #8-32 (4) 6. 191564 PLATE, CAM, ENCL, SYSTEM
7. 310211 ASSY, PNL, LIGHT, TOP BOX 7. 470048 GASKET, DOOR, LCD/BEZEL (2)
8. 850522 INSERT, TOP BOX (REF)
9. 410221 PLEX, TOP BOX 1 2

10. 191594 BKT, MTG, LT PNL, RT

1 2 3

3 4

4 5

7 LOCATE AS SHOWN 6 3 5

5 10
6 7
9 8

P/N 810061 3-24 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

P/N 330788 ASSY, DOOR, SHORT TB, LT PNL P/N 310287 ASSY, POWER SUPPLY
ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION
1. 191559 BKT, MTG, HINGE 1. 130613 END CAP, FRNT, PS ASSY, WELD
2. 450430 SCREW, TPG, HEX WSHR HD #8-32x.375 2. 490450 SUPPLY, POWER, 24 VDC, 240 W, 100-240 VAC
3. 450107 SCREW, SEMS, PH PHIL #4-40x1/4 (10) 3. 450051 SCREW, FLAT HD #6-32x3/8
4. 191564 PLATE, CAM, ENCL, SYSTEM 4. 191608 COVER, PS ASSY
5. 610054 DOOR, SHORT TB 5. 450109 SCREW, SEMS, PH PHIL #6-32x1/2
6. 410234 BEZEL, SHORT TB 6. 191609 END CAP, REAR, PS ASSY
1 2 7. 490449 SUPPLY, POWER 12 VDC, 150 W, 100-240 VAC
8. 450107 SCREW, SEMS, PH PHIL #4-40x1/4
9. 130611 FRAME, PS ASSY, WELD
3
10. 190592 BKT, RTNG, SSR
11. 490289 SSR, I/O, POWER SUPPLY
12. 830056 DECAL, REPLACE SAME FUSE
13. 830565 DECAL, MAIN PWR
14. 490465 SWITCH, ROCKER, MINI EURO STL, 240 VAC
N/S 110417 HRNS, K3-UVR, POWER SUPPLY
N/S = NOT SHOWN

4
3
5 6

5 4
6 2

P/N 330745 ASSY, BV/PTR BEZEL

1
ITEM PART # DESCRIPTION
1. 310278 ASSY, INSERT W/PLEX, BV
2. 530297 PCB, K3-URV, K3-BILB-EXT
3. 450107 SCREW, SEMS, PH PHIL #4-40x1/4
4. 310277 ASSY, BEZEL W/PLEX
5. 530298 PCB, K3-URV, K3-BILB 7
6. 450115 SCREW, SEMS, PH PHIL #8-32x1/4
7. 191622 BKT, MTG, BEZEL BV 14 13 12 11 10 9 8
8. 191623 PLT, GND, BILL ENTRY
9. 830535 DECAL, BILL ENTRY, TOP (REF) P/N 330706 ASSY, BELLY DOOR
10. 830536 DECAL, BILL ENTRY, BTM (REF) ITEM PART # DESCRIPTION
1 1. 191551 DOOR, BELLY
2. 191551 LATCH, BELLY DOOR
3. 450430 SCREW, TPG, HEX WSHR HD#8-32 X .375
REFERENCE 10 2 4. 330705 ASSY, LOGO, BELLY DOOR
2 3
3
REFERENCE 9
1

6
5

6 4 3
7

P/N 810061 3-25 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

P/N 330881 ASSY, BEZEL, BV, JCM SENTRY P/N 330099 ASSY, BV DOOR SWITCH
ITEM PART # DESCRIPTION
ITEM PART # DESCRIPTION
1. 191622 BKT, MTG, BZL, BV
2. PLT, GRND, BILL ENTRY 1. 450144 NUT, NYLOK, #2-56 (2)
191623
2. 191643 CVR, SW, BV DOOR
3. 310277 ASSY, BEZEL W/PLEX
3. 490050 SW, OMRON, SBMIN, W/LEVER ACT
4. 310278 ASSY, INSERT W/PLEX, BV
4. 190596 BKT, SWITCH, BV DOOR
5. 450107 SCREW, SEMS, PH PHIL #4-40 X 1/4 (2)
NS 110054 HRNS, BILL DOOR SWITCH
6. 450115 SCREW, SEMS, PH PHIL #8-32 X 1/4 (4)
4
7. 530297 PCB, K3-URV, K3-BILB-EXT 3
8. 530347 PCB, JCM SENTRY BEZEL
9. 830535 DECAL, BILL ENTRY, TOP 2

10. 830742 DECAL, SENTRY BV, BILL ENTRY

P/N 330698 ASSY, HSG, BV, JCM

ITEM PART # DESCRIPTION
P/N 330952 ASSY, CPU HOUSING, K3 1. 450110 SCREW, SEMS, PH PHIL #6-32x1/4
2. 191817 BKT, FILLER, BV DR
ITEM PART # DESCRIPTION 3. 130591 ASSY, WELD, BV HSG
1. 110308 HRNS, KS, LOGIC DOOR SW (NOT SHOWN) 4. 450014 NUT, HEX, KEP #4-40
2. 130602 HOUSING, LOGIC BOX, WELD 5. 490046 SW, OMRON, SB MIN W/ROLLER ACT
3. 190020 CAM, LOCK, CPU DOOR 6. 450144 NUT, NYLOK #2-56
4. 191070 FAN, GUARD, 3.25” MTG 7. 191540 BKT, SW, CASH BOX
5. 310304 ASSY, KP3 MAIN BOARD 8. 190048 CAM, DOOR, BV
6. 450015 NUT, HEX, KEP #6-32 (4) 9. 710000 LOCK, BARREL, .625 LG (FOR SHIPPING)
7. 450081 SCREW, PH PHIL, M3 X 8 10. 470005 GSKT, BLK, .50x.50, w/PSA, ROLL
8. 450110 SCREW, SEMS, PH PHIL #6-23 X 1/4 (9) N/S 110056 HRNS, BILL VALIDATOR SW 2 (JCM)
9. 450146 GUIDE, PCB, 6IN, CPU HSG (2) N/S 110055 HRNS, BILL VALIDATOR SW 1 (JCM)
10. 450366 NUT, HEX #2-56 N/S = NOT SHOWN
11. 450389 TAG, SECURITY
12. 490046 SW, OMRON, SBMIN, W/ ROLLER ACT
3
13. 490526 DECAL, LICENSE, WINDOWS 1 2
4
14. 530054 FAN, LOGIC BOX, 600mm HRNS
15. 530307 K3-IFB BACKPLANE PCB
16. 530352 MEMORY MODULE 8 9
17. 710000 LOCK, BARREL, .625 LG (FOR SHIPPING)

5
6
7

P/N 810061 3-26 © 2010 Konami Gaming Inc.

PODIUM KP3 PARTS, ASSEMBLIES & HARDWARE

P/N 330699 ASSY, HSG, BV, MEI, CASHFLOW SCM P/N 330879 ASSY, HSG, BV, ARDAC
ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION
1. 130591 ASSY, WELD, BV HSGN 1. 130679 ASSY, HSGN, BV, WELD
2. 190048 CAM, DOOR, BV #4-40 2. 190048 CAM, DOOR, BV
3. 710000 LOCK, BARREL .625 LG (FOR SHIPPING) 3. 191540 BKT, SW, CASHBOX
4. 450014 NUT, HEX, KEP #4-40 4. 191817 BKT, FILLER, BV DOOR
5. 191721 BKT, FILLER, BV DOOR 5. 450014 NUT, HEX, KEP #4-40
6. 470005 GSKT, BLK, .50x.50, w/PSA, ROLL 6. 450110 SCREW, SEMS, PH PHIL #6-32-1/4 (4)
7. 710000 LOCK, BARREL, .625 LG (FOR SHIPPING)
1
470005 GSKT, BLK, .50 X .50 W/PSA ROLL

4 5

2
3

P/N 330838 ASSY, HSG, BV, MEI, CASHFLOW SC P/N 330886 ASSY, HSG, BV, JCM, 1000 NOTE
ITEM PART # DESCRIPTION
ITEM PART # DESCRIPTION
1. 130591 ASSY, HSGN, BV, WELD
1. 130591 ASSY, WELD, BV HSGN 2. 190048 CAM, DOOR, BV
2. 190048 CAM, DOOR, BV
3. 191540 BKT, SW, CASHBOX
3. 191689 BKT, SW, CASHBOX, MEI
4. 191721 BKT, FILLER, BV DOOR
4. 191721 BKT, FILLER, BV DOOR
5. 450014 NUT, HEX, KEP #4-40
5. 450014 NUT, HEX, KEP #4-40
6. 450110 SCREW, SEMS, PH PHIL #6-32-1/4 (4)
6. 450110 SCREW, SEMS, PH PHIL #6-32-1/4 (4)
7. 450144 NUT, NYLOK #2-56
7. 710000 LOCK, BARREL, .625 LG (FOR SHIPPING)
8. 490046 SW, OMRON, SBMIN, W/ ROLLER ACT
470005 GSKT, BLK, .50 X .50 W/PSA ROLL
9. 710000 LOCK, BARREL, .625 LG (FOR SHIPPING)
470005 GSKT, BLK, .50 X .50 W/PSA ROLL
N/S 110055 HRNS, BILL VALIDATOR SW 1, JCM
N/S 110056 HRNS, BILL VALIDATOR SW 2, JCM
N/S = NOT SHOWN

P/N 810061 3-27 © 2010 Konami Gaming Inc.