ANALYSIS IF SINGLY OR DOUBLY REINFORCED CONCRETE BEAM

Material Properties:
f'c = 28 MPa Concrete Compressive Strength
fy = 280 MPa Bending Reinforcement yield Strength
Es = 200,000 MPa Reinforcement modulus Elasticity
ϕ= 0.9 Flexure strength reduction factor (Tension-controlled section)

Section Properties:
b= 500 mm Section Width
h= 500 mm Section Heinght
d' = 41 mm Cover to tension rebar center
cc = 41 mm Cover to compression rebar center

Applied Moment:
Mua = 8 kN-m Factor Moment DL = 4 kPa
Ø= 10 mm Bottom main rebar size LL = 2 kPa

Singly Reinforced Section Properties:

ec = 0.003 Concrete compressive strain
es = 0.005 Creinforcement tensile strain
d= 459 mm Effective depth (h-d)
c = 172.125 mm Neutral axis depth ([ec/(ec+es)]*d = 0.375*d)
β = 0.85 Equivalent depth factor (0.85>={β=0.85-0.05[(f'c-28)/7]}<=0.65)
a = 146.3063 mm Equivalent compression block (β*c)
As = 6218.016 mm Maximum area of steel for singly reinforced section ({[0.85*f'c*b*a*]/fy})
ϕMu = 604.5989 kN-m Maximum resistance moment for singly reinforced section (ϕ*{0.85*f'c*b*a*[d-(a/2)]})/10^6

Design Type:
Mua<ϕMu *Pogii, Singly Reinforced Design Siya!
 NOTE: INPUT YELLOW COLORS ONLY!

NCRETE BEAM

b*a*]/fy})
0.85*f'c*b*a*[d-(a/2)]})/10^6
 Alternate Design Method- Design Procedure of Two-way Slabs using
ACI Moment Coefficients and Approved by BNBC 2013

PROCEDURE

Step 01: Determination of thickness of the slab panel. 0.15

Step 02: Calculation of factored load. 1.2 5 6

1.6 2 3.2
Wu= 1.2*DL+1.6*LL 9.2

Step 03: Determination of moment coefficients. 3

4
M=LA/LB 0.2
2.8
M=A-W/B-W 3.8
0.736842
Step 04: Calculation of moments.

Positive moments:

MA= CA DL×WDL×LA²+ CA LL×WLL×LA²

MB= CB DL×WDL×LB²+ CB LL×WLL×LB²

Negative Moments:

MA= CA , neg×WT×LA²
MB= CA , neg×WT×LB²
-way Slabs using
y BNBC 2013

CALCULATION

COEFFICIENTS FOR NEGATIVE

m T = Thickness of slab
Ca.neg CASE1
1
0.95
0.9
kN/m² DL = Dead Load 0.85
kN/m² LL = Live Load 0.8
kN/m² WT = Total Load 0.75
0.7
0.65
0.6
0.55
m A = Shorter length of the slab 0.5
m B = Longer length of the slab 0
m W = Width of roof beam
m LA = Length of clear span in short direction Cb.neg CASE1
m LB = Length of clear span in long direction 1
m M = Moment coefficients 0.95
0.9
CASE4 0.85
0.066 = CA negative 0.8
0.034 = CB negative 0.75
0.036 = CA DL positive 0.7
0.019 = CB DL positive 0.65
0.043 = CA LL positive 0.6
0.023 = CB LL positive 0.55
0.5
0
kN.m 2.772224 = POSITIVE MOMENT AT A COEFFICIENTS FOR DEAD LOAD POSITIV
kN.m 2.524112 = POSITIVE MOMENT AT B
kN.m 4.760448 = NEGATIVE MOMENT AT A Ca.dl CASE1
kN.m 8.767968 = NEGATIVE MOMENT AT B 1 0.036
0.95 0.04
0.9 0.045
0.85 0.05
0.8 0.056
0.75 0.061
0.7 0.068
0.65 0.074
0.6 0.081
0.55 0.088
0.5 0.095
0 0.152409

Cb.dl CASE1
1 0.036
0.95 0.033
0.9 0.029
0.85 0.026
0.8 0.023
0.75 0.019
0.7 0.016
0.65 0.013
0.6 0.01
0.55 0.008
0.5 0.006
0 -0.026455

COEFFICIENTS FOR LIVE LOAD POSITIVE

Ca.ll CASE1
1 0.036
0.95 0.04
0.9 0.045
0.85 0.05
0.8 0.056
0.75 0.061
0.7 0.068
0.65 0.074
0.6 0.081
0.55 0.088
0.5 0.095
0 0.152409
Cb.ll CASE1
1 0.036
0.95 0.033
0.9 0.029
0.85 0.026
0.8 0.023
0.75 0.019
0.7 0.016
0.65 0.013
0.6 0.01
0.55 0.008
0.5 0.006
0 -0.026455
 TABLE

COEFFICIENTS FOR NEGATIVE MOMENTS IN SLABS

CASE2 CASE3 CASE4 CASE5 CASE6 CASE7 CASE8 CASE9

0.045 0.05 0.075 0.071 0.033 0.061
0.05 0.055 0.079 0.075 0.038 0.065
0.055 0.06 0.08 0.079 0.043 0.068
0.06 0.066 0.082 0.083 0.049 0.072
0.065 0.071 0.083 0.086 0.055 0.075
0.069 0.076 0.085 0.088 0.061 0.078
0.074 0.081 0.086 0.091 0.068 0.081
0.077 0.085 0.087 0.093 0.074 0.083
0.081 0.089 0.088 0.095 0.08 0.085
0.084 0.092 0.089 0.096 0.085 0.086
0.086 0.094 0.09 0.097 0.089 0.088
0.130818 0.143045 0.104727 0.125864 0.148909 0.117182

CASE2 CASE3 CASE4 CASE5 CASE6 CASE7 CASE8 CASE9

0.045 0.076 0.05 0.071 0.061 0.033
0.041 0.072 0.045 0.067 0.056 0.029
0.037 0.07 0.04 0.062 0.052 0.025
0.031 0.065 0.034 0.057 0.046 0.021
0.027 0.061 0.029 0.051 0.041 0.017
0.022 0.056 0.024 0.044 0.036 0.014
0.017 0.05 0.019 0.038 0.029 0.011
0.014 0.043 0.015 0.031 0.024 0.008
0.01 0.035 0.011 0.024 0.018 0.006
0.007 0.028 0.008 0.019 0.014 0.005
0.006 0.022 0.006 0.014 0.01 0.003
0.06 -0.030091 -0.043045 -0.046 -0.044045 -0.030045
ENTS FOR DEAD LOAD POSITIVE MOMENTS IN SLABS

CASE2 CASE3 CASE4 CASE5 CASE6 CASE7 CASE8 CASE9

0.018 0.018 0.027 0.027 0.033 0.027 0.02 0.023
0.02 0.021 0.03 0.028 0.036 0.031 0.022 0.024
0.022 0.025 0.033 0.029 0.039 0.035 0.025 0.026
0.024 0.029 0.036 0.031 0.042 0.04 0.029 0.028
0.026 0.034 0.039 0.032 0.045 0.045 0.032 0.029
0.028 0.04 0.043 0.033 0.048 0.051 0.036 0.031
0.03 0.046 0.046 0.035 0.051 0.058 0.04 0.033
0.032 0.054 0.05 0.036 0.054 0.065 0.044 0.034
0.034 0.062 0.053 0.037 0.056 0.073 0.048 0.036
0.035 0.071 0.056 0.038 0.058 0.081 0.052 0.037
0.037 0.08 0.059 0.039 0.061 0.089 0.056 0.038
0.056591 0.136773 0.091864 0.051864 0.089682 0.147773 0.092227 0.054409

CASE2 CASE3 CASE4 CASE5 CASE6 CASE7 CASE8 CASE9

0.018 0.027 0.027 0.018 0.027 0.033 0.023 0.02
0.016 0.025 0.024 0.015 0.024 0.031 0.021 0.017
0.014 0.024 0.022 0.013 0.021 0.028 0.019 0.015
0.012 0.022 0.019 0.011 0.017 0.025 0.017 0.013
0.011 0.02 0.016 0.009 0.015 0.022 0.015 0.01
0.009 0.018 0.013 0.007 0.012 0.02 0.013 0.007
0.007 0.016 0.011 0.005 0.009 0.017 0.011 0.006
0.006 0.014 0.009 0.004 0.007 0.014 0.009 0.005
0.004 0.011 0.007 0.003 0.006 0.012 0.007 0.004
0.003 0.009 0.005 0.002 0.004 0.009 0.005 0.003
0.002 0.007 0.004 0.001 0.003 0.007 0.004 0.002
-0.015 -0.012864 -0.021318 -0.017227 -0.023773 -0.020136 -0.016227 -0.017864

ENTS FOR LIVE LOAD POSITIVE MOMENTS IN SLABS

CASE2 CASE3 CASE4 CASE5 CASE6 CASE7 CASE8 CASE9

0.027 0.027 0.032 0.032 0.035 0.032 0.028 0.03
0.03 0.031 0.035 0.034 0.038 0.036 0.031 0.032
0.034 0.035 0.039 0.037 0.042 0.04 0.035 0.036
0.037 0.04 0.043 0.041 0.046 0.045 0.04 0.039
0.041 0.045 0.048 0.044 0.051 0.051 0.044 0.042
0.045 0.051 0.052 0.047 0.055 0.056 0.049 0.046
0.049 0.057 0.057 0.051 0.06 0.063 0.054 0.05
0.053 0.064 0.062 0.055 0.064 0.07 0.059 0.054
0.058 0.071 0.067 0.059 0.068 0.077 0.065 0.059
0.062 0.08 0.072 0.063 0.073 0.085 0.07 0.063
0.066 0.088 0.077 0.067 0.078 0.092 0.076 0.067
0.104955 0.121818 0.121818 0.101636 0.120636 0.150045 0.122909 0.103818
 CASE2 CASE3 CASE4 CASE5 CASE6 CASE7 CASE8 CASE9
0.027 0.032 0.032 0.027 0.032 0.035 0.03 0.028
0.025 0.029 0.029 0.024 0.029 0.032 0.027 0.025
0.022 0.027 0.026 0.021 0.025 0.029 0.024 0.022
0.019 0.024 0.023 0.019 0.022 0.026 0.022 0.02
0.017 0.022 0.02 0.016 0.019 0.023 0.019 0.017
0.014 0.019 0.016 0.013 0.016 0.02 0.016 0.013
0.012 0.016 0.014 0.011 0.013 0.017 0.014 0.011
0.01 0.014 0.011 0.009 0.01 0.014 0.011 0.009
0.007 0.011 0.009 0.007 0.008 0.011 0.009 0.007
0.006 0.009 0.007 0.005 0.006 0.009 0.007 0.006
0.004 0.007 0.005 0.004 0.005 0.007 0.005 0.004
-0.0205 -0.018955 -0.024 -0.021 -0.025182 -0.022818 -0.021045 -0.021955
 CASE Ca.neg Cb.neg Ca.dl Cb.dl Ca.ll Cb.ll
CASE 1 0 0 0.05 0.026 0.05 0.026
CASE2 0.06 0.031 0.024 0.012 0.037 0.019
CASE3 0 0.065 0.029 0.022 0.04 0.024
CASE4 0.066 0.034 0.036 0.019 0.043 0.023
CASE5 0.082 0 0.031 0.011 0.041 0.019
CASE6 0.083 0 0.042 0.017 0.046 0.022
CASE7 0 0.057 0.04 0.025 0.045 0.026
CASE8 0.049 0.046 0.029 0.017 0.04 0.022
CASE9 0.072 0.021 0.028 0.013 0.039 0.02