Total No. of Questions : 8] SEAT No.

8
23
PA-1536 [Total No. of Pages : 3

ic-
tat
[5926]-156

5s
T.E. (Mechanical)

2:3
02 91
DESIGN OF TRANSMISSION SYSTEM

9:3
(2019 Pattern) (Semester-II) (302051)
0
30
Time : 2½ Hours]
7/0 13 [Max. Marks : 70
0
Instructions to the candidates:
1/2
.23 GP

1) Answer Four questions from the following

2) Draw neat labeled diagrams wherever necessary
E
81

3) Figures to the right side indicate full marks.

8
C

23
4) Use of non programmable electronic calculator is permitted.

ic-
5) Assume Suitable/Standard data if necessary.
16

tat
8.2

5s
Q1) a) Explain the following terms Hydrodynamic Bearing and Hydrostatic
.24

2:3
Bearing with neat sketch. [5]
91
49

9:3
b) State the assumptions and write the Reynold’s equation for 2-D flow
30
30

and explain the significance of each term in it? [6]

01
02

c) A single row deep groove ball bearing subjected to following work cycle.
1/2
GP

If L10h = 13000 hrs. Find dynamic load carrying capacity; average speed
7/0

of bearing and system reliability if such four bearings are there? [6]
CE
81

8
23
Fr Fa X Y Race Cs Speed %
.23

(kN) (kN) Rotating rpm Time ic-

16

tat
8.2

5s

5 1.5 0.56 1.1 Inner 1.25 960 30

.24

2:3
91

3.7 0.73 0.56 1.3 outer 1.40 1440 40

49

9:3
30

--- --- --- --- outer --- 720 30

30
01

OR
02
1/2
GP

Q2) a) Explain the designation of rolling contact bearings with neat sketch. [5]
7/0

b) A single row deep groove ball bearing is subjected to Fr = 8 kN, Fa = 3

CE
81

kN, X = 0.56, Y = 1.4 and N = 1200 rpm. Diameter of shaft is 75 mm,

.23

Bearing number 6315 with C=112000 N Find i) L10 for 90% reliability;
16

ii) reliability for l=20000 hrs. [6]

8.2
.24

P.T.O.
49
 c) Explain the following terms; [6]

8
23
i) Dynamic load carrying capacity

ic-
ii) Equivalent bearing load

tat
iii) Load life relationship

5s
2:3
02 91
Q3) a) Explain self-energizing block brake and self-locking block brake. [4]

9:3
0
b) With neat sketch explain Block brake with long shoe? Write the equation

30
7/0 13
for Maximum pressure acts on brake, Frictional Force and Braking torque
0
for the same. [6]
1/2
.23 GP

c) Draw neat sketch diagram of Cone clutch and explain construction and
working. State the advantages, disadvantages and applications of
E
81

8
Centrifugal clutch? [7]
C

23
ic-
OR
16

tat
Q4) a) What are the advantages, disadvantages and applications of Centrifugal
8.2

5s
clutch? [4]
.24

2:3
b) Draw neat sketch for single plate cutch and multi plate clutch. What is
91
49

9:3
difference between single plate clutch and multi plate clutch? [6]
30
30

c) Draw a figure for is internal expanding shoe brake and write the
01
02

assumptions on which its analysis depends? State the observations made

1/2

when the vehicle will be travelling in ‘reverse’ for anti-clockwise rotation

GP

of brake drum? [7]

7/0
CE
81

8
23
Q5) a) State the law of Arithmetic progression used in machine tool gearbox
.23

design. State its advantages and disadvantages. [4] ic-

16

tat
8.2

b) Explain any four parameters considered in kinematic design of multi-

5s

speed gear box? [4]

.24

2:3
91

c) A four speed gear box is to be used for a machine tool drive. The
49

9:3

spindle speeds range between 200 rpm to 820 rpm. Design the gear box.
30
30

[10]
01
02

OR
1/2
GP
7/0

Q6) a) Explain the term: Maximum loss of economic cutting speed. [4]
CE
81

b) Explain the terms [4]

.23

i) Range ratio with reference to machine tool gear box design.

16

ii) Transmission range with reference to machine tool gear box.

8.2
.24

[5926]-156 2
49
 c) Read the structure diagram given below and answer the following

8
23
questions: [10]

ic-
i) What is geometric progression ratio and range ratio of this gear

tat
box?

5s
2:3
ii) Write structure formula for this gearbox;

02 91
9:3
iii) What is the speed of input shaft of the gear box?

0
30
7/0 13
iv) Draw schematic layout diagram of the gearbox and calculate number
0
1/2
of teeth on each gear by assuming 20 teeth on smallest gear of each
.23 GP

stage.
E
81

8
C

23
ic-
16

tat
8.2

5s
.24

2:3
91
49

9:3
30

Q7) a) Explain Hybrid Electric Vehicle with the help of block diagram? What
30

are the advantages and disadvantages of Hybrid Electric Vehicles? [6]

01
02

b) Explain the important factors considered in the design of Hybrid Electric

1/2
GP

Vehicles components? [6]

7/0
CE

c) Explain any six components of Hybrid Electric Vehicles? [6]

81

8
23
OR
.23

Q8) a) ic-
Explain Parallel Configuration of Hybrid Electric Vehicles with the help
16

tat
of Block diagram? [6]
8.2

5s

b) Explain Power Split Device with neat sketch? [6]

.24

2:3
91
49

c) Define Degree of Hybridization. Explain in details Full Hybrid and Plug-

9:3
30

in Hybrid. [6]
30
01
02


1/2
GP
7/0
CE
81
.23
16
8.2
.24

[5926]-156 3
49