Scribd
Upload
65 views2 pages

Mcqc-wps-064 Gr700 8mm Fillet

Uploaded by

Joel Mennie
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
65 views2 pages

Mcqc-wps-064 Gr700 8mm Fillet

Uploaded by

Joel Mennie
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

WELDING PROCEDURE SPECIFICATION

WELDING PROCEDURE SPECIFICATION MCQC-WPS-064


Welding Process FCAW (136) Welding Standard AS1554.4 (SP)
PQR Number MCQC-PQR-064 Positions Qualified 1F, 2F, 4F
Date WPS Issued 17/05/2021 Revision Number 0
Type of weld Fillet weld Size 8mm
Material 1 Material 2 Welding Consumable
Material Specification AS/NZS 3597 AS/NZS 3597 AWS: A5.29 Classification E81Ti-Ni1M H4
Type or Grade Gr700 Gr700 AS/NZS ISO 17632 Classification B-T 55 4 T1-1 C A-N2 U H5
Steel Type 10Q 10Q Electrode Size 1.6mm
Range Qualified Unlimited Shielding Gas Mix Argon+25% C02
Pre-heat and Inter-run Temperatures Flow Rate 18 (Litres per minute)
Combined joint thickness Pre heat temperature Inter-run temp (max) Gas Nozzle Size 19mm (Diameter in mm)
0 - 50mm 80°C 150°C Purge Gas Mix N/A (Percentage)
50 - 100mm 110°C 200°C Purge Gas Mix N/A (Percentage)
≥100mm 150°C 220°C Flux Type /Classification N/A
Technique
PWHT Notes : Components shall be cooled slowly by the use of thermal blankets.
Stringer or Weave Stringer
Multi-run or Single Single
Joint Type Fillet Weld Equal Leg Length Electrode Stick Out /CTWD 20mm
Joint Identification Number F1 Table E3 Initial Cleaning Grind
Root Gap 0mm Root Face N/A Inter-run Cleaning Grind, Needle gun
Included Angle N/A Root Radius N/A Finish Dressing As welded, unless instructed otherwise
Backing Material N/A Back Gouging Method N/A
Run On/Off Tabs C steel with weldability group Number ≤5 Back Gouge Inspection N/A
Current and Polarity DC/EP Peening Not permitted

Joint Assembly Detail Welding Sequence

VOLTAGE AMPERAGE TRAVEL SPEED mm/min ARC ENERGIES KJ/mm


PASS NUMBER SIDE DESCRIPTION
Minimum Maximum Optimum Minimum Maximum Optimum Minimum Maximum Minimum Maximum

All Passes 1 Fillet Weld 21.8 25.0 23.4 220.5 270 245 193 261 1.10 2.10
MCQC certify that the statements in this record are correct and that Welding Supervisor: Joel Mennie
the test welds were prepared, welded, and tested in accordance with
the requirements of the standard and category specified. This WPS Cert No. :AS2214-310809241
has been developed for the exclusive use on Glencore overhaul or
has been developed for the exclusive use on Glencore overhaul or
restoration work. Any intended use of this WPS needs to be approved
by Glencore and MCQC in writing prior to commencement . SIGN: DATE: 17/05/2021

You might also like