PRODUCTS, INC.

When You Simply Want The Very Best

2011 Compliance Guide

HONOR G INTEGRITY G COMMITMENT

 When You Simply Want The Very Best

Teeco is Your Partner

in Meeting NFPA 58 Code Requirements
for 2011 Compliance.

2011 is around the corner. Teeco Products, Inc., with its product
lines, engineering and fabrication services, is here to support the
LP-Gas dealer in complying with NFPA 58 by 2011.

Call on Teeco for all your LP-Gas equipment needs.

Sacramento, CA Auburn, WA Rapid City, SD

Teeco Products, Inc. Teeco Products, Inc. Teeco Products, Inc.
7471 Reese Road 1601 Pike Street NW 414 E Boulevard N
Sacramento, CA 95828 Auburn, WA 98001 Rapid City, SD 57701
Phone: 800-225-6621 Phone: 800-426-9456 Phone: 800-843-8660
Fax: 888-225-6621 Fax: 888-426-9456 Fax: 888-843-8660

www.teecoproducts.com
 2011 Compliance Guide
Table of Contents

2011 Requirements from NFPA 58 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

NFPA 58 Table 5.7.7.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Drawing: Options A, B, C for Vapor Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Drawing: Options E, F, H for Liquid Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Drawing: Containers With Existing Internal Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Product Section
Tank Accessories: Bulkheads, Relief Stacks, Steel Ladder, Hose Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Electrical Controls: Push Button Switch Covers, Tumbler Switch Covers, Switch Boxes . . . . . . . . . . . . . . . . . . . . . . . . .8
Electrical Conduit for Hazardous Location
Rochester Magnetel Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Magnetel Dial Assemblies
Bimetallic Thermometers
Low Pressure Valves
Fusible Link
Y Type Strainers: Paget Style B Iron Strainers, Brass Strainers, Smith Precision Strainers . . . . . . . . . . . . . . . . . . . . . .10
Full Circle Hose Swivels
Ball Valves: Apollo, Jomar, IMT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Flexible Stainless Steel Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Corken Stationary Pumps: Z4500, Z3500
Extra Heavy Nipples: Seamless Black Pipe Nipples, Seamless Black Swage Nipples . . . . . . . . . . . . . . . . . . . . . . . . . .13
Forged Steel Fittings: 45O Elbows, 90O Elbows, Tees, Couplings, Reduced Couplings, Square Head Plugs . . . . . . . . . .14
Forged Steel Fittings (cont’d): Unions, Handlebar Unions, Bushings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Abrasions and Low Temperature Resistant Hose Assemblies
Pipe Wrap Tape
Parker Hose
High Pressure LPG Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Stainless Steel Reinforced
High Pressure LPG Carburetion Hose - Stainless Steel Reinforced
LPG Hose Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Hose Accessories: Pig’s Tail Protective Wrapping for Hose
RegO Products Section
Pressure Relief Valves and Relief Valve Manifolds
External Hydrostatic Relief Valves, DuoPort Pressure Relief Valve Manifolds for Small Storage Containers . . .17
Multiport Pressure Relief Valve Manifold Assemblies for Large Storage Containers . . . . . . . . . . . . . . . . . . . . . .18
Semi-Internal “Pop-Action” Pressure Relief Valve for Large Storage Containers . . . . . . . . . . . . . . . . . . . . . . . . .19
Pressure Gauges, Spanner Wrench, Combination Valve for Bulk Storage Containers . . . . . . . . . . . . . . . . . . . . . . . . . .19

When You Simply Want The Very Best

 Table of Contents
Continued
RegO Products Section (cont’d)
Globe and Angle Valves
V-Ring Seal Globe and Angle Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Flange Seal Globe and Angle Valves
Excess Flow Valves
Excess Flow Valves for Liquid or Vapor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Excess Flow Valves for Vapor or Liquid
Excess Flow Valves for Container Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Excess Flow Valves for Flange Mounting in Container Service
Excess Flow Valves for Liquid or Vapor Withdrawal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Excess Flow Valve for Pressure Gauges
Check Valves and Filler Valves
Back Pressure Valves for Container and Line Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Swing Away Back Pressure Check Valves for Container and Line Applications
Back Pressure Check Valves for Flanged Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Internal Valves
1 1/4” Threaded Internal Valves for Small Capacity Pumping Systems & Bobtail Vapor Equalization . . . . . . . . .25
1 1/4” Threaded Angle Valves for Motor Fuel Dispensers & Small Capacity Pumping Systems
Threaded Internal Valves for Bobtail Delivery Trucks Transports & Stationary Storage Tanks . . . . . . . . . . . . . . .26
Emergency Shutoff Valves
3” Swing Check ESV for Bulk Plants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
2” Swing Check ESV for Bulk Plants
1” Swing Check ESV for Bulk Plants
ESV Accessories
Miscellaneous Equipment
Sight Flow Indicators for Bulk Plants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Pull Away Valves for Transfer Operations
Short Type Hose Couplings for Vapor and Liquid Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
ACME Plugs
Caps and Reducers
ACME Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
1” Rotogages for Large Mobile and Stationary Containers
Rotogage Dials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Rotogage Ordering Information

When You Simply Want The Very Best

 When You Simply Want The Very Best

Engineering, Design & Construction Services

TEECO’s PACA division offers complete engineering, design and construction services to architects, engineers, contractors
and LP-Gas companies for fabrication and installation of LP-Gas facilities. We are committed to excellence in our work.

- Bulk LP-Gas storage facilities.

- Commercial and industrial LP-Gas fuel systems.
- Co-generation energy systems and facilities.
- Engine fuel dispenser systems.
- Railroad tank car transshipment terminals.
- Transport truck transshipment terminals.
- Retail LP-Gas service facilities.

Call TEECO toll free at: 800-225-6621 for an estimate on your next project.
California State License # C36-247936
Oregon State License # 001076-05
Nevada State License # 3-4557-01

www.teecoproducts.com 1 When You Simply Want The Very Best

 2011 Requirements from NFPA 58 (2004 Edition)
5.7.7.2 ASME containers over 4000 gal (15.2m3) water capacity shall be equipped in accordance with 5.7.7.2(A) through
5.7.7.2(G) and Table 5.7.7.3.
(A) Vapor withdrawal openings shall be equipped with either of the following:
(1) A positive shutoff valve located as close to the container as practical in combination with an excess-flow valve installed in
the container
(2) An internal valve
(B) Liquid withdrawal openings in new installations shall be equipped with an internal valve that is fitted for remote closure and
automatic shutoff using thermal (fire) actuation where the thermal element is located within 5 ft (1.5 m) of the internal valve.
(C) Liquid withdrawal openings in existing installations where the container is equipped with an internal valve that is not fitted for
remote closure and automatic shutoff using thermal (fire) actuation shall be equipped for remote and thermal closure by
July 1, 2003.
(D) Liquid withdrawal openings in existing installations shall be equipped with either of the following by July 1, 2011:
(1) An internal valve that is fitted for remote closure and automatic shutoff using thermal (fire) actuation where the thermal ele-
ment is located within 5 ft (1.5 m) of the internal valve
(2) An emergency shutoff valve that is installed in the line downstream as close as practical to a positive shutoff valve in com-
bination with an excess flow valve installed in the container
(E) Vapor inlet openings shall be equipped with either of the following:
(1) A positive shutoff valve that is located as close to the container as practical in combination with either a backflow check
valve or excess-flow valve installed in the container
(2) An internal valve
(F) Liquid inlet openings in new installations shall be equipped with either of the following:
(1) An internal valve that is fitted for remote closure and automatic shutoff using thermal (fire) actuation where the thermal ele
ment is located within 5 ft (1.5 m) of the internal valve
(2) A positive shutoff valve that is located as close to the container as practical in combination with a backflow check valve that
is designed for the intended application and is installed in the container
(G) Liquid inlet openings in existing installations where the container is equipped with an internal valve that is not fitted for remote
closure and automatic shutoff using thermal (fire) actuation shall be equipped for remote and thermal closure by July 1, 2003.
(H) Liquid inlet openings in existing installations shall be equipped with any of the following by July 1, 2011:
(1) An internal valve that is fitted for remote closure and automatic shutoff using thermal (fire) actuation where the thermal ele
ment is located within 5 ft (1.5 m) of the internal valve
(2) An emergency shutoff valve that is installed in the line upstream as close as practical to a positive shutoff valve in
combination with an excess flow valve installed in the container
(3) A positive shutoff valve that is located as close to the container as practical in combination with a backflow check valve that
is designed for the intended application and is installed in the container
(4) A backflow check valve that is designed for the intended application and is installed in the line upstream as close as
practical to a positive shutoff valve in combination with an excess-flow valve installed in the container
(I) Container openings that are not compatible with internal valves shall be permitted to utilize both an excess flow valve installed
in the container and a valve complying with API 607, Fire Test for Soft-Seated Quarter Turn Ball Valves, with the following fea-
tures:
(1) The valve shall be activated either hydraulically or pneumatically and shall fail in the closed position.
(2) The valve shall be equipped for remote closure and thermal actuation with a thermal element located within 5 ft of the valve.

When You Simply Want The Very Best 2 www.teecoproducts.com

 Connection and Appurtenance Requirements for New and Existing Container
Installations in Bulk Plant and Industrial Plants (from NFPA 58, Table 5.7.7.3)

Requirements for Containers of Greater Than 4000 Gal

2001 Gal W.C. with and without Internal Valves**
Greater than 4000
Service Through 4000
Gal W.C.** Without Existing Internal With Existing Internal
Gal W.C.*
Valves (by 7/1/11) Valves

Option A or Option B Option A or Option B

Vapor Inlet Vapor connections on containers installed prior to the effec-
or Option C or Option C
tive date of the 2001 edition of NFPA 58 are not required to
Vapor Outlet Option B or Option C Option B or Option C be modified.

Option A or Option B Option D or Option E or Equip an existing internal

Liquid Inlet Option D or Option E valve for remote closure and
or Option C Option F or Option G
automatic shutoff using ther-
Liquid Outlet Option B or Option C Option E Option E or Option H mal (fire) actuation within 5 ft
of the internal valve.
*Applicable to installations constructed on or after the effective date of this code.
**Applicable to installations constructed prior to the effective date of this code.

Option A: Positive shutoff valve installed as close as practical to a backflow check valve installed in the container.

Option B: Positive shutoff valve installed as close as practical to an excess flow valve installed in the container and sized in
accordance with 5.7.11.1(H).

Option C: Internal valve installed in the container or an excess flow valve in accordance with 5.7.7.2(I).

Option D: Positive shutoff valve installed as close as practical to a backflow check valve designed for the intended applica-
tion and installed in the container.

Option E: Internal valve installed in the container equipped for remote closure and automatic shutoff using thermal (fire) acti-
vation within 5 ft of valve or an excess flow valve in accordance with 5.7.7.2(I).

Option F: Emergency shutoff valve equipped for remote closure and automatic shutoff using thermal (fire) activation installed
in the line upstream as close as practical to an existing positive shutoff valve/excess flow valve combination.

Option G: Backflow check valve designed for the intended application and installed in the line upstream as close as practi-
cal to the existing positive shutoff valve/excess flow valve combination.

Option H: Emergency shutoff valve equipped for remote closure and automatic shutoff using thermal (fire) activation,
installed in the line downstream as close as practical to an existing positive shutoff valve/excess flow valve combination.

www.teecoproducts.com 3 When You Simply Want The Very Best

4
5
6
 2011 Compliance Guide

Tank Accessories
Bulkhead
Vertical fitting orientation. Removable center section. 8 bolts/15 reinforcing bars. Two side rails and center section supplied.

Part Number Description

PBH-2V Bulkhead, two-hole, 2” and/or 1 1/4” pipe
PBH-3V Bulkhead, three-hole, 2” and/or 1 1/4” pipe
PBH-4V Bulkhead, four-hole, 2” and/or 1 1/4” pipe

Relief Stack
3 1/2” tubing welded to 3” pipe.
Part Number Description
PRS-7 Relief Stack, 7’ length, with Breakaway and Rain Cap
PRS-10 Relief Stack, 10’ length, with Breakaway and Rain Cap
27-350Z Relief Stack Rain Cap

Steel Ladder
10 feet long, 18 inches wide. Nine steps.
Part Number Description
PTL Steel Ladder

Hose Tray
Part Number Description
PHT-1 10’ Hose Tray

www.teecoproducts.com 7 When You Simply Want The Very Best

 2011 Compliance Guide

Electrical Controls
Push Button Switch Covers
For use in hazardous locations: Class I, Group C, D; Class II, Group E, F & G;
Class III. NEMA 3, 7 C D, 9 E F G.
Part Number Description
FXCS-0B4 Start / stop switch cover*
*Specify “Dead End” or “Feed Thru” junction box.

Tumbler Switch Covers

For use in hazardous locations: Class I, Group C, D; Class II, Group E, F & G;
Class III, NEMA 7 C D, 9 E F G.
Part Number Description
XS-2C Switch and cover, 20A, 2 pole
20A Replacement Switch

Switch Boxes
For use with push button and tumbler switch covers.
Part Number Description
SWB-1 Switch box, 1/2” hub
SWB-2 Switch box, 3/4” hub
SWB-4 Switch box, (2) 1/2” hubs
SWB-5CO Switch box, (2) 3/4” hubs
SWB-7 Double switch box, 1/2” hub
SWB-11 Double switch box, (2) 3/4” hubs

Electrical Conduit for Hazardous Locations

For use in hazardous locations: Class I, Group C, D; Class II, Group E, F & G; Class III
Part # Description
Junction Box
GRSS-1 Junction Box, 1/2”
GRSS-2 Junction Box, 3/4”
GRSS-3 Junction Box, 1”
Conduit Seals
EYS-1 1/2” Conduit Seal
EYS-2 3/4” Conduit Seal
EYS-3 1” Conduit Seal
Conduit Unions
UNY-105 1/2” Conduit Union
UNY-205 3/4” Conduit Union
UNY-305 1” Conduit Union
UNY-405 1 1/4” Conduit Union
90o Elbow
EL-196 1/2” male x 1/2” female
EL-296 3/4” male x 3/4” female
Electrical Reducing Bushing
RB12-08 3/4” x 1/2” Reducing Bushing
RB16-08 1” x 1/2” Reducing Bushing
RB16-12 1” x 3/4” Reducing Bushing
8 www.teecoproducts.com
 2011 Compliance Guide

Rochester Magnetel Gauges

6300 Series Magnetel Liquid Level Gauge
Liquid level gauges accurately determine the percentage of tank volume
for most liquids in stationary bulk storage applications.
Head: Stainless steel. Dial: Standard direct-read 4" and 8". Gasket: Spiral-
wound, Teflon filled, stainless steel. Float: Stainless steel.
Part Number Description
**6336- 4”, top mounting
**6339- 4”, side, end or angle mounting
**6360- 8”, top mounting
**6342- 8”, side, end or angle mounting
** Specify prefix; Dia: P - propane, 5-95%, A - NH3, 5-95%, C - combination LPG/NH3 Mounting: X
- Straddle, Y - 2" opening, M - Special mobile, V - Vertical
† Specify Mounting Flange Trim: -8 Aluminum, -11 stainless steel (-11 should be used on contain-
ers of 3500 WG).

Magnetel Dial Assemblies

Hall Effect Compatible Magnetel Dials
Magnetically-driven voltage output sender. Utilized on stationary applica-
tions where direct reading plus an electrical signal to a remote fuel level
monitor are required.
Part Number Description Dial Wires
5ABPS02854 4” Magnetel Dial Assembly LPG & NH3 None
5AACS02783 8” Magnetel Dial Assembly

Bimetallic Thermometers
Commonly used on storage tanks, bobtails and transports. Made of 304
stainless steel. For use only with thermowells. -90oF to 130oF. 1/2” MNPTF.
Part Number Description
1750-4 4” Stem length
1750-6 6” Stem length
1750-9 9” Stem length
1750-12 12” Stem length

Low Pressure Valves

ASCO Solenoid Valves
Part Number Description
Normally Closed
8320G182-110VAC 3-way, 1/4” NPT, 110V AC
8320G182-110VDC 3-way, 1/4” NPT, 110V DC

Fusible Link
212oF. fusible link for KCCB internal valves.
Part Number Description
2001-FL Fusible Link

www.teecoproducts.com 9 When You Simply Want The Very Best

 2011 Compliance Guide

“Y” Type Strainers

Paget Style B Iron Strainers
Feature tough, weldable ASTM 536 type 60-45-10 annealed, nodular (ductile) iron bod-
ies. Stainless steel 1/64" perf. (.015625) screens have a tapered, self-aligning seat.
Straight threads standard. 600 psi W.O.G.

Part Number Description

182-S 1 1/4" “Y” type strainer, iron
189-S 2" “Y” type strainer, iron

Brass Strainers
Bronze body with steel plug. Blow-down outlet for easy cleaning. 400 lbs. WOG. With
100 mesh stainless steel screen.

Part Number Description

B182-S 1 1/4" “Y” type strainer, brass
B189-S 2" “Y” type strainer, brass

Smith Precision Strainers

Designed for high pressure LP-Gas service. Ductile iron body, working pressure 600
psi W.O.G. Less resistance to flow, with readily removable screen.

Part Number Description

179-S 1 1/4" NPT inlet x 1 1/4" NPT outlet
185-S 2" NPT inlet x 2" NPT outlet
188-S 3" NPT inlet x 3" NPT outlet

Full Circle Hose Swivels

SMAC Series - Hose Reel, Bulk Head, Loading Arm Applications
Designed specifically for liquefied gas service. They minimize hose fighting and simpli-
fy tank connections. Full bore design eliminates flow restrictions at high delivery rates.
SUPERSEAL mechanical seal, contains no rotating lip seal or o-rings to wear out.
Sealed radial contact ball bearings (rated at 6000 lbs) ease rotation and reduce mis-
alignment problems. No lubrication, greasing, adjustment or periodic maintenance is
required. All seal components are easily replaceable in the field. UL listed for use with
LP-Gas.
90 Degree Swivels
Part Number Size A B
SMAC-114LN 1 1/4" x 1 1/4" 3” 4 5/8”
SMAC-200LN 2” x 2” 3¼” 4 3/4”
SMAC-114CR* 1 1/4" x 1 1/4" 3” 4 5/8”
SMAC-200CR* 2” x 2” 3 1/4” 4 3/4”
*CR indicates Corrosion Resistant model

When You Simply Want The Very Best 10 www.teecoproducts.com

 2011 Compliance Guide

Ball Valves
Apollo Ball Valves
Bronze body, TFE seats and seals. Rated at 600 WOG. UL listed and designed for LP
Gas, natural gas, flammable liquids and heated oil. Optional unplated ball model meets
code requirements. Features easy quarter-turn on/off, a large port to reduce pressure
drop and NPT connections. Lever Handle
Part Number Description
80-101-01 1/4” Bronze ball valve
80-102-01 3/8” Bronze ball valve
80-103-01 1/2” Bronze ball valve
80-104-01 3/4” Bronze ball valve
80-105-01 1” Bronze ball valve
80-106-01 1 1/4” Bronze ball valve
80-107-01 1 1/2” Bronze ball valve
80-108-01 2” Bronze ball valve
80-109-01 2 1/2” Bronze ball valve
80-100-01 3” Bronze ball valve

Jomar Steel Double Union Ball Valves

Double union carbon steel ball valve with 316 stainless steel ball and stem. 100% full
port 3000 WOG / 150 WSP. UL listed for liquid propane. Reversible 304 Stainless Steel
handle.
Part Number Description
100-997 1 1/2” Double Union Ball Valve
101-997 1 1/2” Double Union Ball Valve, Socket weld end
100-998 2” Double Union Ball Valve
101-998 2” Double Union Ball Valve, Socket weld end

IMT Full Port LP-Gas Ball Valves

Low cost, high quality full Port LP-Gas Shutoff Ball Valve. Forged brass body and end
piece. Electronic leakage testing on all valves. IMT manufacturing facilities ISO 9001
Certified. Female Iron Pipe Threads, chrome plated solid ball, Full port opening. Blow-
out proof stem. Made in Europe by IMT Switzerland. Pressure Rating: 600 WOG.
Temperature Range: -25°F to 302°F.
Part Number Description UL, CSA and FM approved
59302NT 1/4” Full port brass gas valve, UL, 600 WOG UL: 250 psi
59303NT 3/8” Full port brass gas valve, UL, 600 WOG CSA: 1/3 psi, 5psi, 125 psi
59304NT 1/2” Full port brass gas valve, UL, 600 WOG FM: 250 psi
59306NT 3/4” Full port brass gas valve, UL, 600 WOG
59308NT 1” Full port brass gas valve, UL, 600 WOG
59310NT 1 1/4” Full port brass gas valve, UL, 600 WOG
59312NT 1 1/2” Full port brass gas valve, UL, 600 WOG
59316NT 2” Full port brass gas valve, UL, 600 WOG

www.teecoproducts.com 11 When You Simply Want The Very Best

 2011 Compliance Guide

Flexible Stainless Steel Connectors

Stainless steel corrugated metal LP gas hose with a stainless steel braided sleeve. 350
psi working, 1750 psi burst pressure.
Part Number Fittings Size
F75-S18 3/4” x 18”
F75-S24 3/4” x 24”
F125-S18 1 1/4” x 18”
F125-S24 1 1/4” x 24”
Ground Joint
F150-S18 1 1/2” x 18”
Union x MPT
F150-S24 1 1/2” x 24”
F200-S18 2” x 18”
F200-S24 2” x 24”
F300-S18 3” x 18”

Corken Stationary Pumps

Corken Coro-Vane Z4500 Stationary Pump
The Z4500 is a four-inch stationary pump designed for transport loading and multiple
bobtail loading applications. If you have two or more bulkheads to load bobtails and
transports and would like to shorten your fill times, the Z4500 is the stationary pump for
you. The Z4500 can fill two 3,000 gallon bobtails in 20 minutes or less at typical oper-
ating RPMs.
Part Number Description
4-Inch Stationary pump, 197 GPM @ 420 RPM -
Z4500
382 GPM @ 780 RPM, 4" 300# ANSI inlet

Corken Coro-Vane Z3500 Stationary Pump

The Z3500 is a three-inch pump designed for stationary and foot mounted truck appli-
cations.
Features and Benefits
• Large diameter non-metallic pins allow this pump to be operated at a higher RPM
without damage.
• High tech materials used on the cam and blades help extend the life of the pump.
• Up to 7% or more capacity at 640 RPM.
• Unlike other three inch stationary pumps rated at 640 RPM, the Z3500 is rated up to
800 RPM providing higher capacity without damage.
• Maintenance is made simple. When it’s necessary to service the pump, simply
remove twelve head bolts to inspect the bearings, seals, side plates, rotor, vanes and
vane drivers.
• Retrofits the Corken model 1021 stationary pump and other three-inch competitive
pumps with little or no change in piping.
Part Number Description
Z3500 3-inch Stationary pump
Z3500-103 W/10 HP 3-inch Stationary pump w/10HP motor

When You Simply Want The Very Best 12 www.teecoproducts.com

 2011 Compliance Guide

Extra Heavy Nipples

(ASTM A-53) - Schedule 80 Pipe - Seamless Black Pipe Nipples

Part Number Size Part Number Size

1152B 1” x 3” 1154E 1 1/2” x 6”
1152B-5 1” x 3 1/2” 1155 2” x Close
1152C 1” x 4” 1155A 2” x 2 1/2”
1152C -5 1” x 4 1/2” 1155B 2” x 3”
1152D 1” x 5” 1155B-5 2” x 3 1/2”
Part Number Size Part Number Size 1152D-5 1” x 5 1/2” 1155C 2” x 4”
1199F 1/4” X Close 1150C-5 1/2” x 3 1/2” 1152E 1” x 6” 1155C-5 2” x 4 1/2”
1199G 1/4” x Short 1150D 1/2” x 4” 1153 1 1/4” x Close 1155D 2” x 5”
1199L 1/4” x 2” 1150D-5 1/2” x 4 1/2” 1153A 1 1/4” x 2” 1155D-5 2” x 5 1/2”
1199H 1/4” x 3” 1150E 1/2” x 5” 1153A-5 1 1/4” x 2 1/2” 1155E 2” x 6”
1199I 1/4” x 4” 1150E-5 1/2” x 5 1/2” 1153B 1 1/4” x 3” 1156 2 1/2” x Close
1199J 1/4” x 5” 1150F 1/2” x 6” 1153B-5 1 1/4” x 3 1/2” 1156A 2 1/2” x 3”
1199K 1/4” x 6” 1151 3/4” x Close 1153C 1 1/4” x 4” 1156A-5 2 1/2” x 3 1/2”
1198E 3/8” x Close 1151B 3/4” x 1 1/2” 1153C-5 1 1/4” x 4 1/2” 1156B 2 1/2” x 4”
1198F 3/8” x Short 1151A 3/4” x 2” 1153D 1 1/4” x 5” 1156B-5 2 1/2” x 4 1/2”
1198K 3/8” x 2” 1151A-5 3/4” x 2 1/2” 1153D-5 1 1/4” x 5 1/2” 1156C 2 1/2” x 5”
1198G 3/8” x 3” 1151C 3/4” x 3” 1153E 1 1/4” x 6” 1156C-5 2 1/2” x 5 1/2”
1198H 3/8” x 4” 1151C-5 3/4” x 3 1/2” 1154 1 1/2” x Close 1156D 2 1/2” x 6”
1198I 3/8” x 5” 1151D 3/4” x 4” 1154A 1 1/2” x 2” 1157 3” x Close
1198J 3/8” x 6” 1151D-5 3/4” x 4 1/2” 1154A-5 1 1/2” x 2 1/2” 1157A 3” x 3”
1150 1/2” x Close 1151E 3/4” x 5” 1154B 1 1/2” x 3” 1157A-5 3” x 3 1/2”
1150A 1/2” x Short 1151E-5 3/4” x 5 1/2” 1154B-5 1 1/2” x 3 1/2” 1157B 3” x 4”
1150A-5 1/2” x 1 1/2” 1151F 3/4” x 6” 1154C 1 1/2” x 4” 1157B-5 3” x 4 1/2”
1150B 1/2” x 2” 1152 1” x Close 1154C-5 1 1/2” x 4 1/2” 1157C 3” x 5”
1150B-5 1/2” x 2 1/2” 1152A 1” x 2” 1154D 1 1/2” x 5” 1157C-5 3” x 5 1/2”
1150C 1/2” x 3” 1152A-5 1” x 2 1/2” 1154D-5 1 1/2” x 5 1/2” 1157D 3” x 6”

Seamless Black Swage Nipples

Part Number Size

1158 3/4” x 1/2”
1159A 1” x 3/4”
1160 1 1/4” x 3/4”
1160A 1 1/4” x 1”
1162A 2” x 1 1/4”
1162B 2” x 1 1/2”
1164A 3” x 2”
1164B 3” x 2 1/2”

www.teecoproducts.com 13 When You Simply Want The Very Best

 2011 Compliance Guide

Forged Steel Fittings

Forged Steel 45o Elbows - 2000 lb. Couplings - 3000 lb.
Part Number Size Part Number Size
1106A 1/4” 1117C 1/4”
1106B 3/8” 1117D 3/8”
1106 1/2” 1118 1/2”
1107 3/4” 1119 3/4”
1108 1” 1120 1”
1109 1 1/4” 1121 1 1/4”
1110 1 1/2” 1122 1 1/2”
1111 2” 1123 2”
1111A 2 1/2” 1124 2 1/2”
1111B 3” 1125 3”

Reduced Couplings - 3000 lb.

Forged Steel 90o Elbows - 2000 lb. Part Number Size
Part Number Size 1190 1/2” x 1/4”
1099A 1/4” 1191 3/4” x 1/2”
1099B 3/8” 1192 1” x 3/4”
1100 1/2” 1193 1 1/4” x 3/4”
1101 3/4” 1193A 1 1/4” x 1”
1102 1” 1194 1 1/2” x 3/4”
1103 1 1/4” 1194A 1 1/2” x 1”
1104 1 1/2” 1194B 1 1/2” x 1 1/4”
1105 2” 1195 2” x 1 1/4”
1105A 2 1/2” 1195A 2” x 1 1/2”
1105B 3” 1196A 2 1/2” x 2”
1197 3” x 1 1/2”
1197A 3” x 2”
1197B 3” x 2 1/2”
Forged Steel Tees - 2000 lb.
Part Number Size Square Head Plugs - 2000 lb.
1111C 1/4” Part Number Size
1111D 3/8” 1128 1/4”
1112 1/2” 1129 3/8”
1113 3/4” 1130 1/2”
1114 1” 1131 3/4”
1115 1 1/4” 1132 1”
1116 1 1/2” 1133 1 1/4”
1117 2” 1134 1 1/2”
1117A 2 1/2” 1135 2”
1117B 3” 1135B 3”

When You Simply Want The Very Best 14 www.teecoproducts.com

 2011 Compliance Guide

Forged Steel Fittings (cont’d)

Forged Steel Bushings - 2000 lb. Forged Steel Handlebar Unions - 2000 lb.
Part Number Size Part Number Size
1153C 1/4” x 1/8” 1165A 1”
1153D 3/8” x 1/4” 1165B 1 1/4”
1136 1/2” x 1/4” 1165C 1 1/2”
1136A 1/2” x 3/8” 1165D 2”
1137 3/4” x 1/4” 1165E 2 1/2”
1137A 3/4” x 3/8” 1165F 3”
1137B 3/4” x 1/2”
1138 1” x 1/4”
1138A 1” x 3/8”
1138B 1” x 1/2”
Abrasion and Low Temperature Resistant
1138C 1” x 3/4” Hose Assemblies
1139 1 1/4” x 1/4”
1139A 1 1/4” x 1/2” Polar-Flex Hose/CGA Type 1 Bobtail Hose
1139B 1 1/4” x 3/4” Designed for superior per-
1139C 1 1/4” x 1” formance in transferring liq-
1140 1 1/2” x 1/4” uid petroleum gas, even in
1140A 1 1/2” x 1/2” sub-zero conditions.
1140B 1 1/2” x 3/4” Flexible, abrasion resistant.
1140C 1 1/2” x 1” Peak efficiency between -
1140D 1 1/2” x 1 1/4” 50oF and +180oF. Male x
1141 2” x 1/4” Male. UL Approved Hose.
1141A 2” x 3/4” Part Number I.D. Length
1141B 2” x 1” PF1-100 100’
1141C 2” x 1 1/4” PF1-125 125’
1141D 2” x 1 1/2” 1”
PF1-150 150’
1141G 2 1/2” x 2” PF1-175 175’
1141H 3” x 1 1/2” *Hose assembly / Coupled / with DOT certification
1141I 3” x 2”

Forged Steel Unions - 2000 lb.

Part Number Size Pipe Wrap Tape
1198A 1/4” Pasco Pipe Wrap Tape
1198 3/8” PVC plastic tape with special
1142 1/2” high tack adhesives formulated to
1143 3/4” resist corrosion.
1144 1”
1145 1 1/4” Part Number Size/Mil Carton Quantity
1146 1 1/2” 9051 1” x 100ft./10 48
1147 2” 9052 2” x 100 ft./10 24
1147A 2 1/2” 9061 1” x 100ft./20 48
1147B 3” 9062 2” x 100ft. 24

www.teecoproducts.com 15 When You Simply Want The Very Best

 2011 Compliance Guide

Hose
High Pressure LPG Hose
350 psi maximum working pressure. UL Listed. 7132-25354E-350 sized for shipment by UPS.
Spiral/ Wt./ Standard
Part Number Size I.D. Size O.D.
Braid 100 ft. Reel Size
7132-25354 1/4” .610” 15 lbs. 700’
7132-25354E-350 1/4” .610” 15 lbs. 350’
7132-38354 3/8” .760” 22 lbs. 550’
4 spirals
7132-50354 1/2” .937” 31 lbs. 450’
7132-75354 3/4” 1.250” 51 lbs. 300’
7132-100354 1” 1.500” 62 lbs. 250’
7232-1252 1 1/4” 1.815” 2 braids 85 lbs. 300’
7232-1503 1 1/2” 2.156” 112 lbs. 150’
3 braids
7232-2003 2” 2.750” 177 lbs. 150’
High Pressure LPG Hose - Stainless Steel Reinforced
Rubber cover. 350 psi maximum working pressure. UL Listed. Cut lengths-bulk lots 300’ to 400’.
Wt./ Standard
Part Number Size I.D. Size O.D. Braids
100 ft. Reel Size
7233-311 5/16” .675” 19 lbs. 500’
7231-751 3/4” 1.250” 61 lbs.
7231-1001 1” 1.500” 1 78 lbs. 100’
7231-1251 1 1/4” 1.750” 96 lbs.
7231-1501K 1 1/2” 2.000” 107 lbs.
150’
7231-2002K 2” 2.625” 2 177 lbs.
High Pressure LPG Carburetion Hose - Stainless Steel Reinforced
Textile braid cover. 350 psi maximum working pressure. UL Listed. Cut lengths-bulk lots 300’ to 400’.
Part Number Size I.D. Size O.D. Wt./100 ft.
FC321-04 1/4” 33/64” 11 lbs.
FC321- 08 1/2” 49/64” 21 lbs.
FC321- 12 3/4” 1 5/64” 37 lbs.

LPG Hose Assemblies Part Number Hose I.D. End Fittings

362-___* 1’ Hose 1” MPT x 1” MPT
High Pressure
363-___* 1 1/4” Hose 1 1/4” MPT x 1 1/4” MPT
Working pressure 350 psi, 1750 psi burst rating 365-___* 2” Hose 2” MPT x 2” MPT
*Please specify hose length
Hose Accessories Part Number Description
Pig’s Tail Protective Wrapping for Hose R20SSG Pigstail wrapping for 3/8” hose
Protect your hose investment with Pig'sTail R25SSG Pigstail wrapping for 1/2” hose
Protective Wrapping. Prevent hose wear due to fric- R32SSG Pigstail wrapping for 3/4” hose
tion and abrasion. Designed for heavy-duty building R40SSG Pigstail wrapping for 1” hose
and protection. Rounded edges for safe installation. R50SSG Pigstail wrapping for 1 1/2” hose
High/low temperature resistance from -40F to 280F. R75SSG Pigstail wrapping for 2” hose

When You Simply Want The Very Best 16 www.teecoproducts.com

 2011 Compliance Guide
RegO Products Section

Pressure Relief Valves and Relief Valve Manifolds

External Hydrostatic Relief Valves
Designed especially for the protection of piping and shut-off valves where there is a possibility of trap-
ping liquid LP-Gas or anhydrous ammonia. They may be installed in pipelines and hoses located
between shut-off valves or in the side boss of RegO® shut-off valves.
Start to Accessories
Valve Container Wrench
Part Discharge Height Pipeaway
Body Connection Hex Protective
Number Setting (Approx)
Material M. NPT Section Cap Adapter or Threads
(PSIG)
3125L 1 9/16” 5/8” Included
1/4” ---
3127L Brass 1 31/32” 7/8” 7545-40
3129L 1/2” 2 19/32” 1 1/8” 3129-40P 3129-10*
SS8001L 400 1/4” 11/16”
7/8” ---
SS8002L Stainless 1/2” 7/8”
---
SS8021L Steel 1/4” 11/16” 1/4” NPSM Threads
1 3/8”
SS8022L 1/2” 3/8” NPT Threads
7/8”
3127U 1/4” 1 31/32” ---
Brass 7545-40
3129U 1/2” 2 19/32” 1 1/8” 3129-10*
SS8001U 1/4” 11/16”
450 7/8” --- 3127 Series
SS8002U Stainless 1/2” 7/8”
---
SS8021U Steel 1/4” 11/16” 1/4” NPSM Threads
1 3/8”
SS8022U 1/2” 7/8” 3/8” NPT Threads
12” F. NPT outlet connection

DuoPort Pressure Relief Valve Manifolds for Small Storage Containers

Designed especially for use as a primary relief device on smaller stationary storage containers, with 2"
NPT threaded couplings. These manifolds allow servicing or replacement of either of the two relief valves
without evacuating the container or loss of service. The operating lever selectively closes off the entrance
port to the relief valve being removed while the remaining valve provides protection for the container and
its contents. The rating of each manifold is based on actual flow through the manifold and a single pres-
sure relief valve, taking friction loss into account. It is not merely the rating of the relief valve alone.

Flow Capacity
Start to Application Relief Valve Included
Container SCFM/Air**
Discharge
Part Number Connection Inlet Accessory UL (at 120%
Setting LP NH3 M. NPT Qty Part Number Connection Pipeaway of Set
(PSIG) Gas
M. NPT Adapters Pressure)
8542G Yes No 3135MG 3135-10* 5,250 (1)
250
AA8542UA250 2” 2 AA3135MUA250 1 1/4” 5,865 (1)
No Yes AA3135-10*
AA8542UA265 265 AA3135MUA265 5,975 (1)
* 2" F. NPT outlet connection.
** Flow rating based on number of relief valves indicated in parenthesis ( ). Flow rates shown are for bare relief valves. Adapters and pipeaways will reduce flow rates as dis-
cussed in forewording information.

www.teecoproducts.com 17 When You Simply Want The Very Best

 2011 Compliance Guide
RegO Products Section

Multiport Pressure Relief Valve Manifold Assemblies for Large Storage

Containers
Designed especially for use as a primary relief device on large stationary pressurized
storage containers with flanged openings. These manifolds incorporate an additional
relief valve, not included in the flow rating, allowing for servicing or replacement of any
one of the relief valves without evacuating the container. The handwheel on the mani-
fold selectively closes off the entrance port to the relief valve being removed while the
remaining relief valves provide protection for the container and its contents. All mani-
fold flow ratings are based on flow through the relief valves after one has been
removed for service or replacement.

Bolt Studs and Nuts

Number
Part Number Consists of: For Use With: For Connection to
Required
Modified 3” - 300# and 4” - ASA
7560-55 1- Bolt Stud All RegO
300# Welding Neck Flange 8
and Nut Multiports
7560-56 Manhole Cover Plate

Multiport Manifold Assemblies

Flow Capacity SCFM/Air**
Start to Application Relief Valve
at 120% of Set Pressure
Container
Part Discharge
Flange
Number Setting Inlet Accessory
LP NH Connection ASME
(PSIG) 3 Qty Part Number Connection Pipeaway UL Rating
Gas Rating
M. NPT Adapters
A8563G 3 18,500 (2)
3” - 300#* A3149MG 2 1/2” ****
A8564AG 4 27,750 (3) Not
A8573G 3 18,500 (2) Applicable
4” - 300# A3149MG ****
A8574G 4 27,750 (3)
250 Yes Yes
A8563AG 3 18,300 (2)
3” - 300#* 2 1/2”
A8564AG 4 Not 27,400 (3)
A3149G ****
A8573AG 3 Applicable 18,300 (2)
4” - 300#
A8574AG 4 27,400(3)
* For use with modified 300# ANSI flange with 4" port.
** Flow rating based on number of relief valves indicated in parenthesis ( ). Flow rates shown are for bare relief valves. Adapters and pipeaways will reduce flow rates as dis-
cussed in forewording information.
*** 2" F. NPT outlet connection.
**** Outlet 312-8N (F) thread, will accept 3" M. NPT pipe thread.

When You Simply Want The Very Best 18 www.teecoproducts.com

 2011 Compliance Guide
RegO Products Section

Semi-Internal "Pop-Action" Pressure Relief Valve for Large Storage Containers 7534-40
Designed especially for use as a primary relief valve on large stationary storage containers,
these low profile relief valves are generally mounted in half couplings. However, they are
designed so that the inlet ports clear the bottom of a full 2" coupling. This assures that the relief
valve should always be capable of maximum flow under emergency conditions. 7534-20

Flow Capacity SCFM / Air* Accessories

Start to Container Suitable for
Part
Discharge Connection UL (at 120% of ASME (at 120% Tanks w/ Protective Pipeaway
Number
Setting (PSIG) M. NPT Set Pressure) of Set Pressure) Surface Area Cap Adapter
Up To:
7534G 250 2” 11,675 10,422 708 Sq. Ft. 7534-40 7534-20
7534G

Pressure Gauges
Especially designed in a variety of sizes and construction for the LP-Gas and anhydrous ammo-
nia industry. All RegO® pressure gauges have a 1/4" M. NPT connection unless otherwise
noted.
Maximum Increment
Part Number Service Case Material Case Size
Pressure Divisions
948B LP-Gas Only 300 PSIG 2” 5 PSI
Steel
A8400 NH3 & LP-Gas 400PSIG 2 1/2” 5 lb.

Spanner Wrench for ACME Connectors

This aluminum spanner wrench is especially designed for use with 2 1/4" and
3 1/4" ACME couplings, adapters and caps.
Part Number For Use with ACME Connector Size
3195-50 2 1/4” & 3 1/4”

Combination Valve for Bulk Storage Containers

Designed for installation on bulk storage containers, this valve combines a pressure gauge mount-
ing and provision for a fixed tube liquid level gauge. The shut-off valve prevents the pressure gauge
from being subjected to constant pressure, thereby prolonging its life and accuracy. The valve may
be closed, and the vent valve opened to vent pressure from the gauge to permit replacement. For
fixed liquid level gauging, the valve can be mounted at the maximum permitted filling level. When
equipped with a dip tube threaded 1/8" M. NPT, it can be installed at any convenient level.
Container Service
Part Number Liquid Level Vent
Connection Connection
1/4” F. NPT for
A2805C 3/4” M. NPT Knurled*
Gauge Mounting
* Has 1/8" F. NPT opening for installing separate dip tube.

www.teecoproducts.com 19 When You Simply Want The Very Best

 2011 Compliance Guide
RegO Products Section

Globe and Angle Valves

V-Ring Seal Globe Valves and Angle Valves for Bulk
Storage Containers, Transports, Bobtails and Plant Piping
Specifically designed to assure positive shut-off and
long, maintenance free service life in liquid or vapor
service on bulk storage containers, transports, bobtails,
cylinder filling plants and plant piping. The high quality
construction and wide variety of sizes make them high-
ly suited for use with LP-Gas, anhydrous ammonia and
in the chemical and petrochemical industries.
Part Number Flow at 1 PSIG Pressure Accessories
Inlet & Outlet Port Drop (Cv) (GPM/Propane)
Buna N Seat Discs Teflon Seat Discs* Hydrostatic
Connection Diameter *** Vent Valve
Relief Valve
Globe Angle Globe Angle Globe Angle
--- --- TA7034P TA7034LP 1/2” F. NPT 3/4” 10.0 14.8
A7505AP A7506AP TA7505AP TA7506AP 3/4” F. NPT 12.0 17.7
A7507AP A7508AP TA7507AP --- 1” F. NPT 1” 17.8 22.0
A7509BP A7510BP TA7509BP TA7510BP 1 1/4” F. NPT 1 1/4” 36.5 54.0
A7511AP A7512AP TA7511AP TA7512AP 1 1/2” F. NPT 43.0 55.5
1 1/2” SS8001U TSS3169
A7511FP --- --- 1 1/2” Flange** 46.0 ---
A7513AP A7514AP TA7513AP --- 2” F. NPT 75.0 88.5
2”
A7513FP A7514FP TA7513FP 2” Flange** 78.0 133.0
A7517AP A7518AP TA7517AP TA7518AP 3” F. NPT
3 1/8” 197.0 303.0
A7517FP A7518FP TA7517FP --- 3” Flange**
* Teflon seat discs on valves built to order.
* * 300# ANSI R.F. Flange.
* * * To obtain approximate flow at other than 1 PSIG pressure drop, multiply flow in chart by square root of pressure drop.
Example: 7514FP @ 9 PSIG = 133 x square root of 9 = 399 GPM/propane. For NH3 flow, multiply propane flow by .90.

Flange Seal Globe and Angle valves for Bulk Storage Containers, Filling Hoses and Plant Piping
Designed to assure positive shut-off and long maintenance-free service life in liquid or vapor service. Ideally suited for use on cylin-
der charging manifolds, truck filling hoses, bulk storage containers and plant piping. The high quality construction and wide variety
of sizes make them highly suited for use with LP-Gas, anhydrous ammonia and in the chemical and petrochemical industries.
Flow at 1 PSIG (Cv) A7704P
Inlet and
Part Number Pressure Drop Accessories
Outlet
(GPM/Propane)*
Connection
(F. NPT) Hydrostatic
Globe Angle Globe Angle Vent Valve
Relief Valve
7704P 7704LP
1/2” 7.3 12.3
A7704P A7704LP SS8001J or
TSS3169
7705P 7706P SS8001L
3/4” 11.5 17.7
A7705P A7706P
* To obtain approximate flow at other than 1 PSIG pressure drop, multiply flow in table by square root of pressure drop.
Example: A7704LP @ 9 PSIG =12.3 x square root of 9 = 36.9 GPM/propane. For NH3 flow, multiply propane flow by .90.
A7706P

When You Simply Want The Very Best 20 www.teecoproducts.com

 2011 Compliance Guide
RegO Products Section

Excess Flow Valves

Excess Flow Valves for Liquid or Vapor
Designed for liquid or vapor use for filling, withdrawal and vapor equalizing in container or line applications.
They are intended for long lines or branch piping where tank-mounted excess flow valves are inadequate.
Approximate Closing Flows
Brass A Inlet B Outlet D Effective
Part C Wrench Vapor SCFH (Propane)
or Connection Connection Length Liquid
Number Hex Flats 25 PSIG 100 PSIG
Steel M. NPT F. NPT (Approx) (GPM/Propane)
Inlet Inlet
12472 4 1,050 1,700
3272E 10 2,100 3,700
Brass
3272F 3/4” 3/4” 1 3/8” 1 3/8” 15 2,800 5,000
3272G
20 3,700 6,900
A3272G Steel
3282A 30 5,850 10,000
3282B Brass 40 7,600 13,600
1 1/4” 1 1/4” 2” 1 5/16”
3282C
50 9,000 16,300
A3282C Steel
7574 90 15,200 28,100
1 1/2” 1 1/2” 2 1/4” 1 3/4”
7574L Brass 70 14,000 25,000
3292A 3282A
75 14,200 24,800
A3292A Steel
3292B Brass 2” 2” 2 7/8” 1 7/8”
100 18,100 32,700
A3292B
Steel
A3292C 122 22,100 37,600
* Based on horizontal installation of excess flow valve. Flows are slightly more when valves are installed with outlet up; slightly less when installed with outlet down.
NOTE: Multiply flow rate by .94 to determine liquid butane flow and by .90 to determine liquid anhydrous ammonia flow.

Excess Flow Valves for Vapor or Liquid

Designed especially for filling, withdrawing or vapor equalizing in half and full coupling installations.
Ideal for container service where welded-in dip pipes are not provided. For vapor use, mount in the
bottom opening with a threaded dip pipe. For liquid use, mount in the top opening with a threaded
dip pipe. These may also be installed in pipe lines provided the connection is made to the male inlet
thread and not the female dip pipe connection.
Approximate Closing Flows***
Inlet Outlet
Wrench Hex Vapor SCFH
Part Number Connection Connection Liquid
Flats 25 PSIG 100 PSIG
M. NPT NPT (GPM/Propane)
Inlet Inlet
A2137 2” Male and 1 50 10,000 17,000
2”* 2 7/16”
A2137A 1/4” Female 70 14,000 25,000
2139 3” Male and 125 26,500 46,000
3”** 3 1/2”
2139A 2” Female 160 32,700 57,200
* 114" F. NPT Dip Pipe Connection A2137 Series
** 2" F. NPT Dip Pipe Connection
*** Based on horizontal installation of excess flow valve. Flows are slightly more when valves are installed with outlet up; slightly less when installed with outlet down.
NOTE: Multiply flow rate by .94 to determine liquid butane flow and by .90 to determine liquid anhydrous ammonia flow.

www.teecoproducts.com 21 When You Simply Want The Very Best

 2011 Compliance Guide
RegO Products Section

Excess Flow Valves for Container Service

Designed for mounting in threaded full or half couplings in container installations. They may be used for filling, withdrawal or vapor
equalizing applications. The exceptionally low pressure drop makes them ideal for pump suction lines. If a riser pipe to the vapor
space is used with these valves, the minimum inside diameter of the riser pipe must be at least two times the valve thread size in
order not to restrict flow to the side inlet ports.
Approximate Closing Flows*
For Use with Inlet Outlet
Wrench Vapor SCFH (Propane)
Part Number this Type of Connection Connection Liquid
Hex Flats 25 PSIG 100 PSIG
Coupling M. NPT NPT (GPM/Propane)
Inlet Inlet
A8523 Half 3/4” 3/4” Male 1 1/8” 15 5,170 8,800
A8525 Half 1 1/4” 1 1/4” Male 1 3/4” 35 12,540 21,560
A7537L4 Half
75 13,00 25,600
A7537L4F Full
A7537N4 Half 2” Male and 1
2” 2 5/8” 125 25,000 42,500
A7537N4F Full 1/4” Female
A7537P4 Half
150 30,500 52,000
A7537P4F Full
A7539R6 Half
150 32,100 55,500
A7539R6F Full
A7539T6 Half 3” Male and
3” 3 3/4” 200 39,400 68,300
A7539T6F Full 2” Female
A7539V6 Half
250 51,100 88,700 A7537N4
A7539V6F Full
* Based on horizontal installation of excess flow valve. Flows are slightly more when valves are installed with outlet up; slightly less when installed with outlet down.
NOTE: Multiply flow rate by .94 to determine liquid butane flow and by .90 to determine liquid anhydrous ammonia flow.

Excess Flow Valves for Flange Mounting in Container Service

Designed for mounting in flanged tank connections with internal threads in the bottom of a container. They
may be used in filling, withdrawal or vapor equalizing application. They provide high flow capacity with low
pressure drop to minimize pump inlet line cavitation. If a riser pipe to the vapor space is used with these
excess flow valves, the minimum inside diameter of the riser pipe must be at least two times the valve thread
size in order not to restrict flow to the side inlet ports. Flange mounted excess flow valves are readily acces-
sible for servicing and completely enclosed and protected in event of fire. Because there is no direct connec-
tion between external piping and the valve, stresses imposed on piping will not affect the excess flow valve.
Approximate Closing Flows*
Inlet Connection
Part Number For Installation Liquid Vapor SCFH
M. NPT
(GPM/Propane) 25 PSIG Inlet 100 PSIG Inlet
A3500L4 75 13,000 22,500
A3500N4 2” 125 25,000 42,500
A3500P4 150 30,500 52,00
A3500R6 Slotted Body 150 32,100 55,500
A3500T6 3” 200 39,400 68,300
A3500V6 250 51,100 88,700
A4500Y8 4” 500 89,000 154,000 A3500L4
* Based on horizontal installation of excess flow valve. Flows are slightly more when valves are installed with outlet up; slightly less when installed with outlet down.
NOTE: Multiply flow rate by .94 to determine liquid butane flow and by .90 to determine liquid anhydrous ammonia flow.

When You Simply Want The Very Best 22 www.teecoproducts.com

 2011 Compliance Guide
RegO Products Section

2723C
Excess Flow Valves for Liquid or Vapor Withdrawal
These valves are designed for bottom mounting in consumer stor-
age tanks for liquid service. They may also be top mounted for
vapor service. These valves are designed especially for use with
RegO® globe and angle valves.

A8013D

Approximate Closing Flows**

Inlet Connection Outlet Connection Wrench Hex Vapor SCFH (Propane)
Part Number Liquid
M. NPT F. NPT Flats
(GPM/Propane) 25 PSIG Inlet 100 PSIG Inlet
A8013D 3/4” 39
8,700 14,700
A8013DA 1 1/4” 1” 1 7/8” 44
A8013DB 1 1/4” 55 10,900 19,300
2723C 1 1/4”* 3/4” 1 11/16” 20 3,900 6,900
* 34" F. NPT Dip Pipe Connection
** Based on horizontal installation of excess flow valve. Flows are slightly more when valves are installed with outlet up; slightly
less when installed with outlet down.
NOTE: Multiply flow rate by .94 to determine liquid butane flow and by .90 to determine liquid anhydrous ammonia flow.

Excess Flow Valve for Pressure Gauges

Designed for container use in pressure gauge installations to min-
imize excess gas discharge in the event the pressure gauge is
sheared. A suitable shut-off valve should be installed between this
valve and the pressure gauge to allow convenient gauge replace-
ment.

2884D
Approximate Closing Flows*
Inlet Connection Outlet Connection Wrench Hex Vapor SCFH (Propane)
Part Number Liquid
M. NPT F. NPT Flats
(GPM/Propane) 25 PSIG Inlet 100 PSIG Inlet
2884D 3/4” 1/4” 1 1/16” N/A 60 110
* Based on horizontal installation of excess flow valve. Flows are slightly more when valves are installed with outlet up; slightly
less when installed with outlet down.
NOTE: Multiply flow rate by .94 to determine liquid butane flow.

www.teecoproducts.com 23 When You Simply Want The Very Best

 2011 Compliance Guide
RegO Products Section

Check Valves and Filler Valves A3176

Back Pressure Check Valves - General Information

RegO® Back Pressure Check Valves are designed to allow flow in one direction only. The check,
normally held in the closed position by a spring, precludes the possibility of flow out of the con-
tainer. When flow starts into the container, the pressure overcomes the force of the spring to
open the check. When the flow stops or reverses, the check closes. Metal-to-metal seats will
allow slight leakage after closure. These valves will restrict the escape of container contents in
the event of accidental breakage of the piping or fittings.

Back Pressure Valves for Container and Line Applications A3276BC

Designed to provide protection of a container opening when desired flow is always into the ves-
sel. May be used in line applications where flow must be limited to one direction. When used
with the appropriate single check filler valve, the combination forms a double check filler valve
suitable for use in filling of bulk storage tanks. 3146S

A B C D
Propane Liquid Capacity at Various Differential
Part Number Inlet Outlet Wrench Effective
Pressures (GPM)
Connection Connection Hex Flats Length
Brass Steel F. NPT M. NPT (Approx) 5 PSIG 10 PSIG 25 PSIG 50 PSIG
--- A3146
3/4” 3/4” 1 3/8” 1 5/16” 11 16 25 36
3146S* ---
3176 A3176 1 3/8” 28 40 63 89
1 1/4” 1 1/4” 2”
--- A3276BC* 2 1/2” 32 45 73 103
--- A3186 2” 2” 2 7/8” 2 7/16” 124 175 276 391
--- A3196 3” 3” 4” 3 5/16” 297 420 664 939
*Soft seat version.
NOTE: Multiply flow rate by .94 to determine liquid butane capacity and by .90 to determine liquid anhydrous ammonia capacity.

Swing Away Back Pressure Check Valves for Container or Line Applications
Designed to provide protection of a container opening when desired flow is always into the vessel.
May also be used in the line applications where flow must be limited to one direction. When used
with the appropriate single check filler valve, the combination forms a double check filler valve suit-
able for use in filling of bulk storage tanks. The swing-away check offers more efficient flow rates than
conventional designs. It swivels open vertically to reduce pressure drop across the valve and
improves flow rates.
Inlet Outlet Propane Liquid Capacity at Various
Part Number Wrench
Connection Connection Differential Pressures (GPM)
Hex Flats
F. NPT M. NPT
Brass Steel 5 PSIG 10 PSIG 25 PSIG 50 PSIG
6586D A6586D 2” 2” 2 7/8” 190 270 420 600 6586D
NOTE: Multiply flow rate by .94 to determine liquid butane capacity.

When You Simply Want The Very Best 24 www.teecoproducts.com

 2011 Compliance Guide
RegO Products Section

Back Pressure Check Valves for Flanged Installation

Designed to provide high flow capacity and allow more efficient tank filling than conventional designs.
The unobstructed throat area reduces flow turbulence through the valve, thereby reducing pressure
drop. Large flow channels and spacious side ports assure ample capacity for the most demanding
high capacity filling operations. The valve is designed for installation in internally threaded flanges in
container bottoms.
Flange Propane Liquid Capacity at Various Differential
Part Wrench Overall
Connection M. Pressures (GPM)
Number Hex Flats Length
NPT 5 PSIG 10 PSIG 25 PSIG 50 PSIG
A3400L4 2” 5 1/4” 223 316 500 707
Slotted
A3400L6 3” 5 9/32” 424 600 949 1342
NOTE: For installation in flange tank connections with internal threads, see the "Flanged Installation in Container" section under "Excess A3400L6
Flow Valves." Multiply flow rate by .94 to determine liquid butane capacity and by .90 for liquid anhydrous ammonia capacity.

Internal Valves
1 1/4" Threaded Internal Valve for Small Capacity Pumping
Systems & Bobtail Vapor Equalization
Designed primarily for use with LP-Gas and anhydrous ammonia as a
main valve on small capacity pumping systems, NH3 nurse tanks and
inline installations. It may also be installed in the vapor equalizing open-
ing on bobtail delivery trucks. Installation is quick and easy, and it fits in
both full and half couplings, as well as in-line applications. The valve may
be actuated manually by hand or cable. Note: A3209D replaces A3209R. A3209D A3209TL & A3209PA
Closing Flow** LP-Gas Vapor Capacity**
Inlet Outlet Accessories
(GPM) (SCFH/Propane)
Part Number Connection Connection
25 PSIG 100 PSIG Thermal Pneumatic Compact Pneumatic
M. NPT F. NPT LP-Gas NH3
Inlet Inlet Latch Actuator Actuator
A3209D050 50 45 13,300 22,900
1 1/4”* 1 1/4” A3209TL A3209PA A3209PAF
A3209D080 80 72 15,700 26,700
*Installs in full or half coupling **Data for flow in half coupling

1 1/4" Threaded Angle Valve for Motor Fuel Dispensers & Small Capacity Pumping Systems
Designed primarily for use with LP-Gas and anhydrous ammonia as a main valve on pump systems with
small capacity, such as motor fuel dispensers. It may also be installed in bottom liquid withdrawal open-
ings in NH3 nurse tanks or the vapor equalizing opening of bobtail delivery trucks. Installation is quick
and easy, and must be installed in a modified half coupling or the equivalent. The valve may be actuated
manually by cable or pneumatically. Note: A3209DT replaces A3210A065.
Closing Flow** LP-Gas Vapor Capacity**
Inlet Outlet Accessories
(GPM) (SCFH/Propane)
Part Number Connection Connection
25 PSIG 100 PSIG Thermal Pneumatic Compact Pneumatic
M. NPT F. NPT LP-Gas NH3
Inlet Inlet Latch Actuator Actuator
A3209DT050 50 45 13,300 22,900
1 1/4”* 1 1/4” A3209TL A3209PA A3209PAF
A3209DT080 80 72 15,700 26,700
*Installs in full or half coupling **Data for flow in half coupling

www.teecoproducts.com 25 When You Simply Want The Very Best

 2011 Compliance Guide
RegO Products Section

A3212R Series

Threaded Internal Valves for Bobtail Delivery Trucks Transports

& Stationary Storage Tanks
Designed primarily for use with LP-Gas and anhydrous ammonia for liquid
withdrawal; vapor transfer or vapor equalization of bobtail delivery trucks,
transports, stationary storage tanks, and in-line installations. The valve may
be operated manually by cable or pneumatically.
A3213R Series
A3212R & A3213R Series
Closing Flow (GPM) Closing Flow (GPM)
Inlet Outlet Accessories
Half Coupling Full Coupling
Part Number Connection M. Connection F.
NH3 NH3 Thermal Pneumatic
NPT NPT LP-Gas LP-Gas
Latch Actuator
A3212R105 105 95 65 59
A3212R175 2’ 2” 175 158 100 90
A3212R250 250 225 130 117
A3213R150 150 135 125 113 A3213TL A3213PA
A3213R200 200 180 160 144
3” 3”
A3213R300 300 270 250 225
A3213R400 400 360 325 293

A3212RT Series A3213PA

A3212RT & A3213RT Series

Closing Flow (GPM) Closing Flow (GPM)
Inlet Outlet Accessories
Half Coupling Full Coupling
Part Number Connection M. Connection F.
NH3 NH3 Thermal Pneumatic
NPT NPT LP-Gas LP-Gas
Latch Actuator
A3212RT105 105 95 65 59
A3212RT175 2’ 2” 175 158 100 90
A3212RT250 250 225 130 117
A3213RT150 150 135 125 113 A3213TL A3213PA
A3213RT200 200 180 160 144
3” 3”
A3213RT300 300 270 250 225
A3213RT400 400 360 325 293

When You Simply Want The Very Best 26 www.teecoproducts.com

 2011 Compliance Guide
RegO Products Section

Emergency Shutoff Valves

3" Swing Check ESV for Bulk Plants
Designed for installation in liquid or vapor transfer lines at LP-Gas or Anhydrous
Ammonia bulk plants to provide for quick shut-off of liquid or vapor flow in the event
of an accidental pull-away, line break or hose rupture.

Inlet & Outlet Liquid Flow Capacity at 10

Part Number For Use With:
Connections PSIG Drop (GPM)
6024 LP-Gas 1,260 (LP-Gas)
3” F. NPT
AA6024 NH3 1,130 (NH3)

2" Swing Check ESV's for Bulk Plants

Especially designed for installation in liquid transfer lines at LP-Gas or anhydrous ammonia bulk
plants to provide for quick shut-off of liquid or vapor flow in the event of an accidental pull-away or
hose rupture, both of which can cause a fire. Replaces 7605B and AA7605B 2" Swing Chek ESV's.
Inlet and Outlet Liquid Flow Capacity at 10
Part Number For Use Only With:
Connections PSIG Pressure Drop (GPM)
6016 LP-Gas 475 (LP-Gas)
2” F. NPT
AA6016* NH3 427 (NH3)
* Must be actuated pneumatically, manually by cable or by cable connection to pull-away valve.

1 1/4" Swing Check ESV for Bulk Plants

Especially designed for installation in liquid or vapor transfer lines at LP-Gas or
Anhydrous Ammonia bulk plants to provide for quick shut-off of vapor or liquid flow
in the event of an accidental pull-away, line break or hose rupture, any of which can
cause a fire. Meets NFPA 58 and UL requirements.
Part Inlet & Outlet Liquid Flow Capacity at 10
For Use With:
Number Connections PSIG Pressure Drop (GPM)
6010 LP-Gas 259 (LP-Gas)
1 1/4” F. NPT
AA6010 NH3 233 (NH3)

ESV Accessories 6016-60D

For use with all 3 ESVs shown above
Part Number Description 6016-60C
6016-60C Pneumatic Remote Open/Close Kit
6016-60D Pneumatic Remote Close Kit

www.teecoproducts.com 27 When You Simply Want The Very Best

 2011 Compliance Guide
RegO Products Section

Miscellaneous Equipment
Sight Flow Indicators for Bulk Plants
Designed to promote maximum pump efficiency, these indicators enable bulk plant operators to visually inspect liquid flow conditions.
With glass on both sides of the indicator, flow can be observed from either side, even under some poor light conditions. The integral
swing check also serves as a back-check valve to prevent reverse flow and product loss if the hose fails in a loading operation. By
installing an indicator on the upstream side of the plant pump, suction conditions can be observed and the pump speed adjusted to
obtain the maximum possible flow rate without cavitation. Additionally, if an indicator is installed in the piping at the loading rack, just
ahead of the loading hose, the operator can maintain a constant check on pump conditions.
Both installations are designed to allow for observation to provide maximum pump efficiency
and assure safe plant pump operation. In compressor operations a sight flow indicator installed
in the liquid line will give a visual indication when the tank car or transport is emptied.
Compressor operation can then be immediately reversed to start recovery of the vapor.
Inlet / Outlet
Part Number Length
Connections
A7794 2” F. NPT 5 3/4”
A7796 3” F. NPT 7 3/8”

Pull Away Valves for Transfer Operations

Designed especially to provide pull-away protection for LP-Gas and anhydrous ammo-
nia transfer operations including transport and delivery truck loading and unloading,
engine fuel container filling and miscellaneous cylinder filling operations. When prop-
erly fastened to the inlet end of the discharge hose, the valve is designed to stop gas
escape from both upstream and downstream lines in the event of a pull-away. An
excessive tension pull causes the valve to automatically separate, closing two internal
back pressure checks. Only a few cubic centimeters of gas escape at the instant of
separation. It is recommended that a convenient means be provided to safely remove
the pressure from the line upstream of each coupling half to enable reassembly of the
valve. To reassemble, simply push the male half firmly into the female half until the
retaining balls slip into the retaining groove. Check for leaks after reassembly. NOTE:
It is recommended that pull-away valves be safety-tested at least monthly to confirm
that they will separate properly in the event of a pullaway. Dry nitrogen or other inert
gas is suggested for a source of pressure during such tests.
LP-Gas Liquid Flow Capacity at Various
Inlet/Outlet Disconnect Reconnect Differential Pressures (GPM)*
Length of
Part Number Connections Force Approx Force Approx
Valve
F. NPT lbs. lbs. 5 PSIG 10 PSIG 25 PSIG 50 PSIG
A2141A6
3/4” 130 80 3 7/8” 11 16 25 36
A2141A6L
A2141A8
1” 75 50 4 9/16” 21 30 47 67
A2141A8L
A2141A10 1 1/4” 160 25 5 5/8” 52 75 120 170
A2141A16 2” 300 50 14 5/16” 250 350 550 750
* To determine NH3 liquid flow capacity, multiply by .90.

When You Simply Want The Very Best 28 www.teecoproducts.com

 2011 Compliance Guide
RegO Products Section

Short Type Hose Couplings for Vapor and Liquid Service

Hose Coupling
Part Tailpiece Hose End Overall
Material Style Connection Connection
Number Bore to Nut Length
(M. NPT) (F. ACME)
3175A A 1” 1 3/4” 3/4” 2” 2 7/8”
Brass
3185 1 1/4” 2 1/4” 1 3/16” 2 1/16” 3 1/8”
Brass Nut & B
3195 2” 3 1/4” 1 13/16” 2 1/8” 3 5/8”
Steel Nipple
3175 Series

ACME Plugs
Specifically designed to withstand the everyday abuse given hose end valves on delivery trucks and
hose end couplings on risers in bulk plants. These rugged plugs protect the coupling tip as well as
prevent the entrance of dirt, dust, snow and rain. They also prevent possible gas contamination from
these same sources. The heavily ribbed outer surface permits hand-tight make-up.
Chain & Ring Fits Pipe Size
Part Number Material M. ACME
Up To:
C5763N 1 1/4” 3/4”
Nylon
C5765N 1 1/4”
1 3/4”
5765PR Brass Not Applicable
C5767N 2 1/4” 1 1/4”
Nylon
C5769N 3 1/4” 2”

Caps and Reducers

Cap with Chain & Ring
Cap Only Part
Ring Fits Pipe Size Material Thread Connection
Part Number Number
Up To:
3174-91 3/4” 3174-9P Cycolac 1 3/4” F. ACME
3184-90 2” --- 2 1/4” F. ACME
Brass
3194-90 3” 3194-9 3 1/4” F. ACME

3194-90

www.teecoproducts.com 29 When You Simply Want The Very Best

 2011 Compliance Guide
RegO Products Section

ACME Adapters
ACME x Female NPT
For Spare
Part A B C D E
Material Gasket Order
Number M. ACME F. NPT Hex Diameter
Part No.
5766F 2 1/4” 1 1/4” 2 1/4” 2 5/16” 1 3/8” A3184-8R
Brass
5768H 3 1/4” 2” 3 1/2” 3 5/8” 2 1/8” A3194-8R

ACME x Male NPT

For Spare
Part A B C D E
Material Gasket Order
Number M. ACME M. NPT Hex Diameter
Part No.
5765F 1 3/4” 1 3/4” 2 1/8” 3/4” A2697-20R
1 1/4”
5767F Brass 2 1/4” 2 3/4” 2 5/16” 1 3/16” A3184-8R
5769H 3 1/4” 2” 3 3/8” 2 7/8” 1 7/8” A3194-8R

Rotogages®
1" Rotogages® for Large Mobile and Stationary Containers
Rotogages® are designed to provide an accurate determination of LP-Gas or anhydrous ammonia con-
tainer contents. They mount in a standard 1" NPT coupling on large mobile or stationary containers. To
operate the Rotogages®, the vent valve is opened and the dip tube rotated slowly from the container vapor
space to the liquid space. The difference in appearance of the discharge indicates when the liquid level
is reached. Dial readings then indicate the percentage of product in the container.

Rotogage® Dials
Part Number Service Container Size
A9091-18L All Sizes
LP-Gas
A9091-18LX Over 1,200 US Gallons
A9091-18N NH3 All Sizes

Rotogage® Ordering Information

Part Number For Container Inside Diameter
For Use with LP-Gas For Use with NH3

For Mobile For Stationary For Mobile For Stationary Ellipsoidal Heads Hemispherical Heads
or Stationary Containers or Stationary Containers Side End Side End
Containers Only Containers Only Mounted Mounted Mounted Mounted
A9091-M48* A9091-M48 A9091-M48 A9091-M48 62”-79” 109”-147” 62”-79” 62”-79”
A9091-M60 A9091-M60 A9091-M60 A9091-M60 80”-99” --- 80”-99” 80”-99”
A9091-M72* A9091-M72 A9091-M72* A9091-M72 100”-147” --- 100”-147” 100”-147”
* Supported Design.
NOTE: The dip tube must be cut to the required length (1/2" of container inside diameter minus 5 3/4").

When You Simply Want The Very Best 30 www.teecoproducts.com

Notes
 2011 Compliance Guide
Provided by Teeco Products, Inc.

Corporate Headquarters
Teeco Products, Inc.
16881 Armstrong Avenue
Irvine, CA 92606
Phone: 800-854-3463
Fax: 888-854-3463

Customer Service Locations

Teeco Products, Inc. Teeco Products, Inc. Teeco Products, Inc.
7471 Reese Road 1601 Pike Street NW 414 E Boulevard N
Sacramento, CA 95828 Auburn, WA 98001 Rapid City, SD 57701
Phone: 800-225-6621 Phone: 800-426-9456 Phone: 800-843-8660
Fax: 888-225-6621 Fax: 888-426-9456 Fax: 888-843-8660

www.teecoproducts.com
2011 Guide 11/08