Scribd
Upload
409 views2 pages

TANKSHIELD PW Data Sheet

Uploaded by

N.prem kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
409 views2 pages

TANKSHIELD PW Data Sheet

Uploaded by

N.prem kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

HOME SHIELD

TANKSHIELD PW

Product Description
Home Shield Tankshield PWis a two-component polymer modified cementitious
waterproof slurry mortar consisting of a liquid polymer and a cement – based
mix incorporating graded aggregates and additives. It is applied over concrete
and mortar, which on curing forms an excellent waterproof and protective
semi-rigid layer over the surface and thus prevents water infiltration.

Recommended Use
• Potable water tanks and Swimming pools
Product Attributes •
•
Exterior waterproofing of basement retaining walls
Interior 7 exterior waterproofing and damp- proofing of old and new concrete
Waterproofing • Bridge decks, canals, sewage treatment areas etc.
Waterproof • Waterproof bottom coating for tiles, granite, marble and other natural stones
concrete
structures
Toxicity
Water permeability
Remarkable
resistance towards
ingression of water

Usability Non – toxic.


Easy to mx and Can be used for potable
apply pre-batched water containing
components
structures
Brushable consistency

Adhesive properties
Excellent adhesion Mixing Ratio Aspect
to concrete, natural
and artificial stones

Temperature
resistance
Enhanced resistance Part A (Liquid ) : Part B (Powder ) -
to freeze-thaw cycles Approx. 1 : 1.5 (by vol.) ; 1:2 (by wt.) Part A: White Liquid
& de-icing salts Part B: Dark Grey Powder
Part A + Part B = Grey Slurry

Slip resistance
Imparts slip
resistance to the Mixed Density Coverage
applied surface

Flexibility
Provides
flexible 1.7 – 2.1Kg /m² / 2 coats
coating 1.65 gm/cc @25° C

Corrosion
Protection
Non-corrosive to
steel and iron
Application Method
Green Pro Certified
Validates our effort in
striving towards cleaner,
more sustainable future
Brush/ Roller / Spray
HOME SHIELD
TANKSHIELD PW

Surface Preparation
• The surface to be applied should be clean & sound, free from any kind of contamination,
dirt etc. Thoroughly wire brush the surface & clean the dust by air compressor or by water
jetting.
• Oil & grease must be removed using degreasing solvents.
• Any damaged surface must be repaired by using crack fillers or Home Shield Advanced
Latex Plus.
• Finally the substrate must be properly pre-wetted to a saturated surface-dry condition.
Mixing
• Shake well the liquid component to a homogenous milky colour.
• Transfer entire quantity of liquid component before mixing into a suitable clean mixing
container.
• Gradually start adding powder component under constant mixing with a stirrer using an
electric power tool (1kw) at slow speed at 250 – 300 rpm for 3- 5 minutes till
homogeneous and uniform free flowing slurry is obtained.

Packs Directions for Application


Concrete slabs or roof slabs
Apply two coat of mixed slurry to be applied to the set concrete @ 1.7 – 2.1 kg/m2 by a
masonry brush, roller or appropriate power spray equipment.
As a slurry coat
Apply slurry coat of mixed material for two coats at a coverage rate of 1.5 kg/m2 over the
set concrete slab by a masonry brush or appropriate power spray equipment.
Water tanks and Swimming pools
15 Kg
Two coats of Latex Shield 2K to be applied @ 1.6 – 1.8 kg/m2 per coat by a masonry brush or
an appropriate power spray equipment.
Pile Heads
Two coats of mixed slurry to be applied on to the pile head @ 0.8 – 1.0 kg/m2 first coat and
1.2 - 1.5 kg/m2 second coat either by a masonry brush or by appropriate power spray
equipment.
Marbles/Stones
It is recommended to apply one coat at the bottom of the marble @ 1.5 mm thick at a
coverage of approximately 1.75 - 2 kg/m2.
All applications where two coats are specified, the second coat should be applied when the
first coat is completely dry.
Over-coating
Over- coating time for the second coat is (4 – 6) hours.
For over - coating, allow the second coat to harden for at least 24 hours prior to over
coating.
The treated area should be protected from direct sunlight and to be damp cured by covering
with damp hessian or similar material.
Precautions
• Do not mix part quantities
• Do not add extra water for dilution
Pot Life • Always add powder to the liquid, vice – versa not recommended
1 hour • Do not add cement or sand in the powder component at site
• Do not expose the applied substrate to water until it is completely cured
• Applied surface must be protected from direct sunlight, foot traffic at green stage of
application

Storage
• Store under cover, away from direct sunlight and protect from extreme environment.
• In hot temperature conditions, it must be stored in 30 C controlled temperature.
Shelf Life
12 months from the date
of manufacture
Health & Safety
• While using Tankshield PW use rubber hand gloves, dust mask and safety goggles.
• Tankshield PW is alkaline and contact with skin or eyes should be avoided.
• In case of any contact to eyes should be washed immediately with clean water and seek
medical advice.

Version No: BPP1/11/2014. Please note that this data sheet supersedes all previous versions.

BERGER PAINTS INDIA LIMITED


Berger House, 129 Park Street, Kolkata 700 017 | CONSUMER RELATIONS MANAGER Ph: 1800-103-6030
Fax: 91-33-2249-9729/9009 | SMS BERGER to 56767 | Email: [email protected] | www.bergerpaints.com

You might also like