AEC

Unit 3

MOSFET circuits

3.1 MOSFET structure

A MOSFET is the common transistor used in digital circuits. It can be made with either p-type or n-type
semiconductors, complementary pairs of MOS transistors can be used to make switching circuits with
very low power consumption, in the form of CMOS logic.

MOSFETs are particularly useful in amplifiers due to their input impedance being nearly infinite which
allows the amplifier to capture almost all the incoming signal.

MOSFETs are available in two basic forms:

 Depletion Type: The transistor requires the Gate-Source voltage (VGS) to switch the device “OFF”.
The depletion-mode MOSFET is equivalent to a “Normally Closed” switch.
 Enhancement Type: The transistor requires a Gate-Source voltage(VGS) to switch the device “ON”.
The enhancement-mode MOSFET is equivalent to a “Normally Open” switch.

Structure:

It is a four-terminal device with source(S), gate (G), drain (D) and body (B) terminals. The body is
frequently connected to the source terminal, reducing the terminals to three. It works by varying the
width of a channel along which charge carriers flow (electrons or holes).

Figure 1. MOSFET has a vertically oriented four-layer structure.

 The p-type middle layer term as the body.
 The n– layer is the drift layer.
 This layer is lightly doped as compared to the drain and source layer.
 The breakdown voltage of power MOSFET determines from the width of the drift layer.
 First and last both layers are an n+ layer. First layer is the source layer and the last layer is the drain
layer.

The charge carriers enter the channel at source and exit via the drain. The width of the channel is
controlled by the voltage on an electrode is called gate which is located between source and drain.

A p-channel MOSFET structure has exactly opposite doping profile.

 The GATE terminal is not directly connected with p-type, there is an oxide layer between the metal
and semiconductor.
 This oxide layer act as a dielectric layer between the metal and the semiconductor. It forms a MOS
(metal oxide semiconductor) capacitance at the input of the MOSFET.
 This capacitance is large (>1000 pF). The oxide layer gives good insulating property by providing
the SiO2 layer that isolates the gate terminal from the body layer.

V-I characteristics

Figure 2. V-I characteristics of MOSFET

It has three regions: saturation, cut-off, and ohmic region.

 When the gate-source voltage is less than the threshold voltage, the MOSFET is in the cut-off state.
To avoid breakdown the drain to source breakdown voltage should be greater than the applied
voltage. The avalanche breakdown takes place.
 When the gate-source voltage is greater than threshold the power MOSFET goes into the ohmic
region and the drain to source voltage is small. In this region, the power dissipation is low.
 In the saturation region, the drain current is almost independent of the drain to source voltage. It
is only dependent on the gate to source voltage. The gate voltage is greater than the threshold
voltage. The drain current increase with the increase in the gate to source voltage.

3.2 MOSFET as a switch

The drain terminal (D) of the MOSFET is connected to the supply voltage VS via the drain resistor
RD while its source terminal (S) is grounded. It has an input voltage V i applied at its gate terminal (G)
while the output Vo is drawn from its drain.

Figure 3. n-channel Enhancement MOSFET functioning as a switch

 When Vi = 0V, which means the gate terminal of the MOSFET is left unbiased. As a result, the
MOSFET will be OFF and operates in its cut-off region wherein it offers a high impedance path to the
flow of current which makes the IDS almost equivalent to zero.
 As a result, even the voltage drop across RD will become zero due to which the output voltage Vo will
become almost equal to VS.
When Vi > VT under this condition, the MOSFET will start to conduct and if the V S provided is greater
than the pinch-off voltage VP of the device then the MOSFET starts to operate in its saturation region.
 The device will offer low resistance path for the flow of constant I DS, almost acting like a short circuit.
As a result, the output voltage will be pulled towards low voltage level, which will be ideally zero.
Thus, the output voltage alters between VS and zero depending on whether the input provided is less
than or greater than VT, respectively. Thus, it can be concluded that MOSFET can be made to function
as electronic switches when made to operate between cut-off and saturation operating regions.

3.3 MOSFET as an Amplifier

Figure 4. MOSFET as as Amplifier

This is a conceptual amplifier for two resons:

 The bias with VGs is impractical.
 In ICs large valued resistors take up too much physical space.

To operate as small -signal amplifier we bias MOSFET in saturation region. For analysis of DC operating
point we set vgs =0 so that

iD = ½ Kn’ W/L (vgs -Vt) 2 --------------------(1)

From the circuit VDS = VDD – ID RD ------------------------------(2)

For operation in saturation region

vGD ≤ Vt ------ vgs – vds ≤ Vt

or vds ≥ vgs – Vt --------------------------------------------------(3)

where the total drain to source voltage is

vds = Vds + vds

(bias) AC

With an AC signal applied at the gate

Vgs = VGS + vgs -------------------------------(4)

Substituting (4) in (1) we get

2 2
iD = ½ kn’ W/L (VGS + vgs – Vt) = ½ kn’ W/L (VGS – Vt) + vgs ] ----------(5)

2 2
= ½ kn’ W/L (VGS – Vt) + 2/2 kn ‘ W/L (VGS – Vt) vgs + ½ kn’ W/L v gs ---------(6)

The last term is non linear in vgs which is not desorable for linear amplifier. Hence for linear operation
the last term should be small with respect to linear term and the second term is proportional to vgs.

Or vgs<< 2 (VGS – Vt) ------------------------------------------(7)

If this small signal condition (7) is satisfied then from (6) the total drain current is a approximately
linear summation.

iD ͌ ID + i d --------------------------------------------------------------(8)

where

id = kn’ W/L (VGS – Vt) vgs ‘ ---------------------------------------(9)

From this expression (9) we see that AC drain current id is related to vgs by transistor
transconductance gm.

gm = id / vgs = kn’ W/L (VGS – Vt) [S]

which is sometimes expressed in terms of overdrive voltage Vo V = Vgs – Vt

gm = kn’ W/L Vov [S]

3.4 Small signal Model

In saturation mode the MOSFET acts as a voltage controlled device . The control voltage is vgs and
output current is id which gives rise to small signal model π model.
Figure 5. Small signal model of MOSFET

Ig=0 and vgs ≠ 0 the infinite input impedance

ro models the finite output resistance .

We know that gm = k’n W/L (Vgs – Vt)

Hence it can be shown that

gm = 2Id/ Vov = Id / (Vgs – Vt) /2

 Biasing circuits

N-channel enhancement mode MOSFET circuit shows the source terminal at ground potential and is
common to both the input and output sides of the circuit. *The coupling capacitor acts as an open
circuit to d.c. but it allows the signal voltage to be coupled to the gate of the MOSFET
Figure 6. Biasing circuit

As Ig = 0 in VG is given as,

VG = VGS = (R2/R1+R2) VDD

Assume VG > VT , MOSFET is biased in the saturation region, the drain current is,

ID = K(VGS – VT) 2

Applying KVL to drain current we have

VDS = VDD – ID RD

If VDS > VDS (sat) = VGS – VT the the MOSFET is biased in the saturation region.

If VDS < VDS (sat) then the MOSFET is biased in the non -saturation region, and the drain current is given
by, ID

For the circuit shown in figure assume that R1 = 30KΩ and R2 = 10 KΩ. Rd = 40KΩ . Vdd =
10V and VT=1V , Vgs = 2V and K = 0.1mA /V2 . Find Id and VDS
VG = VGS = (R2/R1+R2) VDD = (10/10+30) (10) = 2.5V

Assuming that the MOSFET is biased in the saturation region the drain current is

VDS = VDD – ID RD = 10 – (0.1)(40) = 6V.

Here, the source is tied to +VDD, Which, become signal ground in the a.c. equivalent circuit. Thus, it is
also a common-source circuit.

The d.c. analysis for this circuit is essentially the same as for the n-channel MOSFET circuit. The gate
voltage is given by,

VG = (R2/R1 + R2) (VDD)

And the source to gate voltage is given by

VSG = VDD -VG

Assuming VGS <VT or VSG > |VT| the device in the saturation region and the drain current is given by

2
ID = K(VSG + VT)

And the source to drain voltage is given by

VSD = VDD – ID RD

If VSD > VSD (sat) then MOSFET is in saturation region.

IF VSD < VSD(sat) MOSFET is in non-saturation region.

For the circuit shown in figure calculate ID , VDS, VG and VS

Applying KVL to the input circuit.

VGS = VG – VS

= 3 – I S RS Since VS = IS RS

= 3 – I D RS Since ID = IS

We have

ID = IDSS ( 1 – VGS / VP ) 2
Substituting the value of VGS we get

2 -3
ID = IDSS ( 1 – (3 – ID RS)/Vp) = 20 x 10 ( 1 – ( 3 – ID x 1.2 x 10 3 / -6)

-3
= 20 x 10 ( 1 – [ (-0.5) + 200 ID ]) 2 = 20 x 10 -3
( 1.5 -2)

-3
= 20 x 10 (2.25 – 600ID + 40000ID 2)

2
I D = 0.045 – 12 I D + 800 I D

2
800 I D – 13 I D + 0.045 =0

Solving for quadratic equation we get

= -(-13) ± [ (13) 2 – 4(800)(0.045)] ½ / 2(800)

= 13 ± [ 169 -144] ½ / 1600 = 13 ± / 1600 = 13 ± 5 /1600 = 5mA or 11.25 mA

If we calculate the value of VDS taking ID = 11.25mA we get

VDS = VDD – ID ( RD + RS)

-3
= 12 – 11.25 x 10 ( 500 + 1.2 x 10 3)

= 12 – 19.125 = -7.125

Practically the value of VDS must be positive hence ID= 11.25 mA is invalid

Hence take ID = 5mA

-3
VDS = VDD – ID (RD + RS) = 12 – 5 x 10 (500 + 1.2 x 10 3) = 12 – 8.5 = 3.5 V

-3 3
VGS = 3 – ID RS = 3- 5 x 10 x 1.2 x 10 = 3 – 6 = -3 V

-3 3
Vs = ID RS = 5 x 10 x 1.2 x 10 = 6V

3.5 Common Source Amplifier

Common source amplifier with Voltage divider bias

Figure 7. Common Source Amplifier

Now Rs will be the part of low frequency equivalent model as shown in

figure.

Figure 8. Equivalent model

Note that RG = R1 || R2
Z1 = RG = R1 || R@

Zo’ = rd + gm Rs rd + Rs

Zo’ = rd + Rs ( μ + 1)

Zo = [ rd + gm Rs rd + Rs] || R D

Zo = [ rd + Rs (( μ + 1)] || R D

Av = -gm RD/ 1+ gm Rs + Rs + R / rd D

3.6 Common Gate Amplifier

In this circuit, input is applied between source and gate and output is taken
between drain and gate.

Figure 9. Common Gate Amplifier

In CG Configuration, gate potential is at constant potential. so, increase in

input voltage Vi in positive direction increase the negative gate source
voltage. Due to I reduces, reduces, reducing the drop I R .
D D D

Since V = V -I R , the reduction in I results in an increase in output voltage.

D DD D D D
Figure 10. Equivalent model

Input Impedance (Zi)

Zi = Rs || Zi’

And

Zi’ = Vi/I

After substituting and simplification,

Vi/I = 1 + R /rd / 1/rd + gm = rd + R / 1 + gm rd

D D

Zi = Rs || Zi’ = Rs || rd + R / 1+gm rd
D

If rd >> R and gm rd >> 1 then we can write

D
Z = Rs || rd / gm rd = Rs || 1/gm
1

Output Impedance

It is given by

Zo = rd || R D

If rd >> R D

Zo = R D

Voltage gain:

Av = Vo/Vi

Vo = - I R D D

Vi = - Vgs

Using KVL to the outer loop after simplication

Av = Vo/ Vi = - Id + R / -Id ( rd + R ) / 1+ gm rd
D D

If rd >> RD and gmrd >>1

Av = R (gm rd) / rd = R gm
D D
3.7 Common Drain Amplifier

In this circuit, input is applied between gate and source and output is taken
between source and drain.

Figure 11. Common Drain Amplifier

In this circuit, the source voltage is

V = V +V
s G GS

When a signal is applied to the JFET gate via C ,VG varies with the signal.
1

As VGS is fairly constant and V = V +V , Vs varies with Vi.

s G GS

The following figure shows the low frequency equivalent model for common
drain circuit.
Input Impedance Z i

Zi = RG
Output Impedance Z o

It is given by

Zo = Zo’ || Rs

Where Zo’ = Vo/Id | Vi=0

Applying KVL to the outer loop we have

Vi + Vgs -Vo =0

Vi=0

Looking at the figure we can write

gm Vgs = Id

But Vgs = Vo

gm Vo = Id

Zo’ = Vo/Id = 1/gm

Zo = 1/gm || Rs

Voltage gain (A ) v

It is given by

Av = Vo/Vi

Looking at the figure we can write

Vo = -Id (rd|| Rs)

And Id = gm Vgs

Vo = -gm Vgs (rd||Rs)

But
 Vi = -Vgs + Vo

= - Vgs + [ -gm Vgs (rd||Rs)

Substitute the value V and V . Then

o i

Av = -gm vgs (rd||Rs) / -Vgs (1+gm (rd||Rs)

= gm (rd||Rs) / 1+gm (rd || Rs)

If rd >> Rs

Av = gm Rs / 1+ gm Rs

If gm Rs >> 1

Av = 1 but it is always less than one.

Common drain circuit does not provide voltage gain.& there is no phase shift
between input and output voltages.

3.8 Small signal equivalent circuits

a- Without early affect

b- With early affect

Figure 12. Small signal equivalent circuit

This relationship can be modelled by a current source. Moreover, the gate of
the MOSFET is essentially an open circuit at DC. Hence, the small-signal
equivalent-circuit model is presented in Figure

When the Early effect has to be accounted for, an output resistor ro can be
added as shown in Figure . The value of ro is given as

r o = |VA|/I where I = ½ kn V 2 ov
D D

The voltage gain is

Av = vds / vgs = -gm (R ||ro) D

The transconductance is given by

gm = k’n (W/L) (V – Vt) = k’n (W/L) V = μ Cox (W/L) V

GS OV n OV

The transconductance can be increased by increasing the W/L ratio, and also
increasing the overdrive voltage V . But increasing VOV implies that the
OV

operating point for VDS has to increase in order for the MOSFET to be in the
saturation region. Also, by using the fact that

I = ½ Kn V
D
2
OV = ½ k’n (W/L) V ov 2

V ov = [ 2I / k’n (W/L)] ½
D

gm = [ 2 k’n (W/L) I ] ½ D

This implies that gm is proportional to the square roots of the drain current I ,
D

and W/L.

 High frequency equivalent circuit.

Figure 13. High frequency equivalent circuit.

Y = 1/Z = YL + Yds + gd + Ygd

Where

YL = 1/RL ; admittance corresponding to RL

Yds = jw Cds ; admittance corresponding to Cds

Gd = 1/rd ; conductance corresponding to rd

Ygd = jw Cgd ;admittance corresponding to Cgd.

I = -gm Vi + Vi Ygd = Vi(-gm + Ygd)

Voltage gain:

The voltage gain for common source amplifier circuit with load RL is given by

Av = Vo/Vi = IZ/Vi = 1/ViY

Substituting the values of I nd Y we get

AV = -gm + Ygd/ YL + Yds + gd + Ygd

At low frequencies Yds and Ygd =0 hence

Av = -gm +Ygd/YL + gd = -gm rd ZL/ (YL +gd) rd ZL = -gmrdZL/ rd + ZL

= -gm ZL where ZL = rd ||ZL

Input Admittance :

Yi = Ygs + (1-Av) Ygd

Input capacitance

Av = -gm R’d

Substituting the value of Av

Yi/jw = Ci= Cgs +(1+gmR’d) Cgd

This increase in input capacitance Ci over the capacitance from gate to

source is called Miller effect.

This input capacitance affects the gain at high frequencies in the operation
of cascaded amplifiers.

In cascaded amplifiers, the output from one stage is used as the input to a
second amplifier. The input impedance of a second stage acts as a shunt
across output of the first stage and Rd is shunted by the capacitance Ci.

Output Admittance:

The output impedance is obtained by looking into the drain with the input
voltage set equal to zero. If Vi = 0 in figure, rd , Cds and Cgd in parallel.
Hence the output admittance with RL considered external to the amplifier is
given by,

Yo = gd + Yds + Ygd

References:
 Op-amps and linear integrated circuit technology Book by Ramakant A. Gayakwad
 Principles of Analog Electronics Textbook by Giovanni Saggio
 Analog electronics Book by Ian Hickman
 Analog Electronics with Op-amps: A Source Book of Practical Circuits Book by Anthony Peyton, V. Walsh, and Y.
Walsh