Access Hardware

LNL-M2220
Intelligent Dual
Reader Controller

Overview Features & Functionality

The LNL-M2220 Intelligent Dual Reader Controller (IDRC) Controller Functionality
provides a single board solution for interfacing one or two • DNS device naming through DHCP extended commands
doors to an OnGuard® system. In addition, other I/O and reader • 6 MB of available on-board, non-volatile flash memory
interface modules can be added on the controller’s downstream • Super Capacitor backed, non-volatile storage of 500,000 events
port to expand its capabilities. The LNL-M2220 controller
• Configurable option for Data-at-Rest encryption
revolutionizes access control system architecture by allowing
• Firmware stored in flash memory, background download of
Ethernet connection directly from an entry location to the
firmware updates supported
OnGuard server, while still providing the security, functionality,
• Supports up to sixteen badge formats
and modularity of LenelS2's proven hardware platform.
The LNL-M2220 controller is scalable for any access control • Biometric template storage support for OSDP™ Biometric and
application, from the most basic to the most sophisticated. In the legacy Bioscrypt® readers
event of communication loss, the LNL-M2220 controller allows • Optional Secondary NIC, USB port (2.0) with optional adapter
nearly all local functionality to continue unimpaired until the • Enhanced anti-passback capabilities
server connection is restored. • Up to 32,000 access level permissions
• Elevator control support for up to 128 floors
Utilizing its native Ethernet communications and a secure
• Individual extended held-open and strike times
32-bit processor, the LNL-M2220 controller can communicate
• Two dedicated inputs for tamper and power failure status
upstream to the host computer through its Ethernet port. The
controller can store up to 250,000 cardholders in non-volatile • Advanced Encryption Standard (AES) 256-bit algorithm for
flash memory, and supports selective download for larger communications to LenelS2 Series 3 reader and I/O modules; AES
cardholder databases. The downstream RS-485 two-wire port 128 bit encryption to LenelS2 Series 2 reader and I/O modules
can be used to connect up to 32 devices (maximum 64 doors). • TLS 1.2 / 1.3 communication to OnGuard
• Support for wireless lock communications hubs from ASSA
Two on-board reader ports support Data1/Data0, Clock/Data, ABLOY Aperio, Schlage AD400, Schlage Engage, and SimonsVoss
Supervised and Unsupervised F2F, Biometric readers and the Gateways
bi-directional RS-485 Open Supervised Device Protocol (OSDP)
Reader Interface Functionality
communications. Each LNL-M2220 controller supports up
• Supports Data 1/Data0, Clock/Data, Supervised and Unsupervised
to sixteen different card formats. The LNL-M2220 controller
F2F and OSDP-compatible RS-485 readers and keypads
includes eight inputs that support normally open, normally
closed, supervised, and unsupervised circuits. In addition, four • Support for OSDP Biometric template transfer and Secure
output relays support fail-safe or fail-secure operation. Channel Encryption
• Door contact supervision (open/closed) and
REX push-button monitor for each door
• Strike control and auxiliary output for each door
• Bi-color reader status LED support plus beeper control,
or 2-wire LED support
• On-board voltage regulator allows 12 VDC reader power
from 24 VDC power source
System Diagram
LNL-M2220
Intelligent System
Controller (ISC) RS-485 Multi-drop
Max 32 Devices up to 4000 ft.

TCP/IP NETWORK
OnGuard® LNL-1300 LNL-1320 LNL-1100 LNL-1200
Security Server Single Reader Dual Reader Input Control Module Output Control Module
Interface Module Interface Module Up to 16 Inputs per Up to 16 Outputs per
LNL-1100 LNL-1200

Motion Sensor Alarm

Option 2.1

Option 2.2

-OR-

Reader Reader Reader

Reader Reader Reader Reader

Specifications The interface is for use in low voltage, Class 2 Circuits only.
The installation of this device must comply with all local fire and electrical codes.

Primary Power 12 to 24 VDC ± 10%, 500 mA maximum (reader current not included) Environmental
Reader Ports 600 mA maximum each (add up to 600 mA to primary power current each) -55° to +85° C, storage
Primary Host Communication Ethernet: 10-BaseT/100Base-TX Temperature
0° to +70° C, operating
Secondary Host Communication USB port (2.0) with optional adapter: pluggable model USB2-OTGE100 Humidity 5 to 95% RHNC
One each: 2-wire RS-485, 2,400 to 115,200 bps, asynchronous, half-duplex, Heat Output at 12 VDC, 20.5 BTU/hr
Serial I/O Device
1 start bit, 8 data bits, and 1 stop bit (BTUs) at 24 VDC, 22.9 BTU/hr
Eight unsupervised / supervised, standard EOL: 1k/1k ohm, 1% 1/4 watt; two Approvals FCC Part 15, CE, RoHS, UL 294
Inputs
unsupervised inputs dedicated for cabinet tamper and UPS fault monitoring
Four relays: Normally open contact (NO): 5 A @ 30 VDC resistive; Normally
Outputs
closed contact (NC): 3 A @ 30 VDC resistive
Memory/Clock backup: Super Capacitor (10 days). Optional, 3V Lithium, type
Battery
BR2330 or CR2330 (battery not included, field installable).
Reader Interface
12 VDC ± 10% regulated, 600 mA maximum each reader (input voltage [VIN]
Parts and Spare Parts
Power (Jumper selectable) must be greater than 17 VDC) or 12 to 24 VDC ± 10% (input voltage passed
through), 600 mA maximum each reader Part No. Description
Data Inputs TTL compatible, F/2F or 2-wire RS-485
9,600 to 115,200 bps, asynchronous, half-duplex, 1 start bit, 8 data bits, and
6 MB on-board flash memory
RS-485 Mode available for cardholder
1 stop bit. Maximum cable length: 2,000 ft. (609.6m)
LED Output TTL levels, high > 3 V, low < 0.5 V, 5 mA source/sink maximum
LNL-M2220 database; 500,000 event
Buzzer Output Open collector, 12 VDC open circuit maximum, 40 mA sink maximum
super capacitor backed RAM
for event log.
Cable Requirements
Power and Relays One twisted pair, 18 to 16 AWG USB-to-Ethernet converter,
Ethernet CAT-5, minimum for LNL X-Series and M-Series
TTL Reader 18 AWG, depending on length and requirements Controllers only. Provides
USB2-
Alarm Input One twisted pair, 30 ohms maximum, typically 22 AWG @ 1,000 ft. (304.8m) optional Secondary NIC
OTGE100
One twisted pair with drain wire and shield, 120 ohm impedance, 24 AWG, connection. Second NIC
RS-485 I/O Device Port
4,000 ft. (1,219m) maximum should be on different subnet
One twisted pair with drain wire and shield, 120 ohm impedance, 24 AWG, than primary NIC.
RS-485 Reader Port
2,000 ft. (610m) maximum
Mechanical
Dimensions 8.0 W x 6.0 L x 1.0 H in. (203.2 x 152.4 x 25mm)
Weight 9.0 oz. (255g) nominal, board only

LenelS2.com
(866) 788-5095

Specifications subject to change without notice.

© 2024 Honeywell International Inc. All Rights Reserved. All trademarks and
service marks referred herein are property of their respective owners. 2024/07