Site / Project Name:
CHECKLIST FOR WELDING JOINT REDIOGRAPHY TEST (Sheet 1/4)
Name of Building/ Area/location : ________________________________
Contractor name: _______Date of checking: ______
Reference Drawing No : _________ Drawing Revision No: _____________
As per Acceptable
S. No Description Actual Remarks
Drawing Tolerance
1 PIPING SYSTEM N/A Y/N N/A
2 MATERIAL DETAILS :-
2a MATERIAL SPECIFICATION
2b TYPE OF JOINTS
2c JOINT SIZE
2d JOINT NUMBER
“Notice to Employees” poster displayed in
3
appropriate numbers and locations
Appropriate radiation warning signs posted at
entrance
Emergency procedures and phone numbers clearly
posted
Whether the barricading with proper warning label
is displayed at the location of radiography
All records such as list of authorized radiographer,
authorized person and radiological officer is
maintained & submitted to Quality Dept./ Safety
Dept.
Proper communication is made in the area about
timing of the activity, type of source and its
hazards with precautionary measures
The “State Regulations for Protection Against
Radiation” policy available
Comments :
Accepted Accepted with comments Rejected
Contractor’s Engineer In-Charge
Name Sign & date
FABS’ / Client’s Engineer In-Charge
Name Sign & date
Site / Project Name:
CHECKLIST FOR WELDING JOINT REDIOGRAPHY TEST (Sheet 2/4)
Name of Building/ Area/location : ________________________________
Contractor name: _______Date of checking: ______
Reference Drawing No : _________ Drawing Revision No: _____________
As per Acceptable
S. No Description Actual Remarks
Drawing Tolerance
“Radiation Safety Manual” available N/A Y/N N/A
Radioactive material and radiation producing
devices secured to prevent unauthorized access
The work area orderly and free from man
movement
Written operating procedures readily available
Whether the activity is carried out under the direct
control of person authorized by BARC
The employed for the job are well aware of
Safety in Radiography?
Whether only authorized and licensed
radiographer is appointed for radiography
All personnel have documented training of the
appropriate type
Personal protective equipment available and worn
appropriately
TLD Badge with Name of Person, Month/Year is
available
Reports of Medical examinations is available
Records of Certified radiographers, Records of
Certified radiographers In charge
Appropriate personnel supplied with dosimeters
Whether dosimeter used by radiographer is issued
on his name by BARC?
Radiation dosimeter &Survey meters been
calibrated
Comments :
Accepted Accepted with comments Rejected
Contractor’s Engineer In-Charge
Name Sign & date
FABS’ / Client’s Engineer In-Charge
Name Sign & date
Site / Project Name:
CHECKLIST FOR WELDING JOINT REDIOGRAPHY TEST (Sheet 3/4)
Name of Building/ Area/location : ________________________________
Contractor name: _______Date of checking: ______
Reference Drawing No : _________ Drawing Revision No: _____________
As per Acceptable
S. No Description Actual Remarks
Drawing Tolerance
Dosimeter &Survey meters in good working order N/A Y/N N/A
The source movement letter is available
Exposure devices containing radiography sources
are kept in a pit room or bunker with locking
arrangement
Strength of source
Accurate and up-to-date isotope receiving logs
kept and available for inspection
Accurate and up-to-date isotope use logs kept and
available for inspection
Whether the exposure rate at barrication
indentified by using radiation survey meter? Is it
below 0.75 millimR/hr?
Integrity of the shield; The integrity of shield is
checked by using Radiation Survey Meter.
Radiation at 5 cm or closer from any accessible
point from the source is measured. Is it below 0.25
MR/hr
Comments :
Accepted Accepted with comments Rejected
Contractor’s Engineer In-Charge
Name Sign & date
FABS’ / Client’s Engineer In-Charge
Name Sign & date
Site / Project Name:
CHECKLIST FOR WELDING JOINT REDIOGRAPHY TEST (Sheet 4/4)
Name of Building/ Area/location : ________________________________
Contractor name: _______Date of checking: ______
Reference Drawing No : _________ Drawing Revision No: _____________
As per Acceptable
S. No Description Actual Remarks
Drawing Tolerance
1 Testing Details N/A Y/N N/A
2 Date of Test
3 Starting Time
4 Ambient Temperature
10
11
12
13
14
15
Comments :
Accepted Accepted with comments Rejected
Contractor’s Engineer In-Charge
Name Sign & date
FABS’ / Client’s Engineer In-Charge
Name Sign & date
Site / Project Name:
