MRCET ECE ES UNIT-3 Notes

UNIT-III
TYPICAL EMBEDDED SYSTEM
ELEMENTS OF EMBEDDED SYSTEMS:
An embedded system is a combination of 3 things, Hardware Software Mechanical
Components and it is supposed to do one specific task only. A typical embedded system contains
a single chip controller which acts as the master brain of the system. Diagrammatically an
embedded system can be represented as follows:

FPGA/ASIC/DSP/SoC
Embedded
Microprocessor/controller
Firmware

Memory

Communication Interface

System
I/p Ports Core O/p Ports
(Sensors)
(Actuators)

Other supporting
Integrated Circuits &
subsystems

Embedded System
Real World

Embedded systems are basically designed to regulate a physical variable (such

Microwave Oven) or to manipulate the state of some devices by sending some signals to the
actuators or devices connected to the output port system (such as temperature in Air
Conditioner), in response to the input signal provided by the end users or sensors which are
connected to the input ports.

N SURESH, Dept. of ECE 73

MRCET ECE ES UNIT-3 Notes

The control is achieved by processing the information coming from the sensors and user
interfaces and controlling some actuators that regulate the physical variable.
Keyboards, push button, switches, etc. are Examples of common user interface input
devices and LEDs, LCDs, Piezoelectric buzzers, etc examples for common user interface
output devices for a typical embedded system.The requirement of type of user interface
changes from application to application based on domain.
Some embedded systems do not require any manual intervention for their operation.
They automatically sense the input parameters from real world through sensors which are
connected at input port. The sensor information is passed to the processor after signal
conditioning and digitization. The core of the system performs some predefined operations
on input data with the help of embedded firmware in the system and sends some actuating
signals to the actuator connect connected to the output port of the system.
The memory of the system is responsible for holding the code (control algorithm and
other important configuration details). There are two types of memories are used in any
embedded system. Fixed memory (ROM) is used for storing code or program. The user
cannot change the firmware in this type of memory. The most common types of memories
used in embedded systems for control algorithm storage are
OTP,PROM,UVEPROM,EEPROM and FLASH
An embedded system without code (i.e. the control algorithm) implemented memory has
all the peripherals but is not capable of making decisions depending on the situational as well
as real world changes.
Memory for implementing the code may be present on the processor or may be
implemented as a separate chip interfacing the processor
In a controller based embedded system, the controller may contain internal memory for
storing code such controllers are called Micro-controllers with on-chip ROM, eg. Atmel
AT89C51.

N SURESH, Dept. of ECE 74

 MRCET ECE ES UNIT-3 Notes

The Core of the Embedded Systems: The core of the embedded system falls into any one
of the following categories.


General Purpose and Domain
 Specific Processors
 o Microprocessors

 o Microcontrollers

o Digital Signal Processors

 
 Programmable Logic Devices (PLDs)
 
 Application Specific Integrated Circuits (ASICs)

 
Commercial off the shelf Components (COTS)

GENERAL PURPOSE AND DOMAIN SPECIFIC PROCESSOR:

Almost 80% of the embedded systems are processor/ controller based.

The processor may be microprocessor or a microcontroller or digital signal processor,
depending on the domain and application.
Microprocessor:
A silicon chip representing a Central Processing Unit (CPU), which is capable of
performing arithmetic as well as logical operations according to a pre-defined set of
Instructions, which is specific to the manufacturer

In general the CPU contains the Arithmetic and Logic Unit (ALU), Control Unit and
Working registers

Microprocessor is a dependant unit and it requires the combination of other hardware like
Memory, Timer Unit, and Interrupt Controller etc for proper functioning.

Intel claims the credit for developing the first Microprocessor unit Intel 4004, a 4 bit
processor which was released in Nov 1971

· Developers of microprocessors.
Intel – Intel 4004 – November 1971(4-bit)
Intel – Intel 4040.
Intel – Intel 8008 – April 1972.
Intel – Intel 8080 – April 1974(8-bit).
Motorola – Motorola 6800.
Intel – Intel 8085 – 1976.
Zilog - Z80 – July 1976

N SURESH, Dept. of ECE 75

 MRCET ECE ES UNIT-3 Notes

Microcontroller:

A highly integrated silicon chip containing a CPU, scratch pad RAM, Special and
 General purpose Register Arrays, On Chip ROM/FLASH memory for program storage,
Timer and Interrupt control units and dedicated I/O ports
 
 Microcontrollers can be considered as a super set of Microprocessors


Microcontroller can be general purpose (like Intel 8051, designed for generic applications
 AVR from Atmel Corporation.
and domains) or application specific (Like Automotive
 Designed specifically for automotive applications)

  working,
Since a microcontroller contains all the necessary functional blocks for independent
they found greater place in the embedded domain in place of microprocessors
 
 Microcontrollers are cheap, cost effective and are readily available in the market
 
Texas Instruments TMS 1000 is considered as the world‟s first microcontroller

Microprocessor Vs Microcontroller:

Microprocessor Microcontroller
A silicon chip representing a Central Processing Unit A microcontroller is a highly integrated chip that
(CPU), which is capable of performing arithmetic as contains a CPU, scratch pad RAM, Special and
well as logical operations according to a pre-defined set General purpose Register Arrays, On Chip
of Instructions ROM/FLASH memory for program storage, Timer
and Interrupt control units and dedicated I/O ports
It is a dependent unit. It requires the combination of It is a self contained unit and it doesn’t require
other chips like Timers, Program and data memory external Interrupt Controller, Timer, UART etc for
chips, Interrupt controllers etc for functioning its functioning

Most of the time general purpose in design and Mostly application oriented or domain specific
operation
Doesn‟t contain a built in I/O port. The I/O Port Most of the processors contain multiple built-in I/O
functionality needs to be implemented with the help of ports which can be operated as a single 8 or 16 or 32
external Programmable Peripheral Interface Chips like bit Port or as individual port pins
8255
Targeted for high end market where performance is Targeted for embedded market where performance is
important not so critical (At present this demarcation is invalid)

Limited power saving options compared to Includes lot of power saving features
microcontrollers

N SURESH, Dept. of ECE 76

MRCET ECE ES UNIT-3 Notes

General Purpose Processor (GPP) Vs Application Specific Instruction Set Processor (ASIP)

 
General Purpose Processor or GPP is a processor designed for general computational tasks


GPPs are produced in large volumes and targeting the general market. Due to the high
 production, the per unit cost for a chip is low compared to ASIC or other specific
volume
 ICs


A typical general purpose processor contains an Arithmetic and Logic Unit (ALU) and Control
 Unit (CU)


Application Specific Instruction Set processors (ASIPs) are processors with architecture
and instruction set optimized to specific domain/application requirements like Network

processing, Automotive, Telecom, media applications, digital signal processing, control
 applications etc.

ASIPs fill the architectural spectrum
between General Purpose Processors and Application
 Specific Integrated Circuits (ASICs)


The need for an ASIP arises when the traditional general purpose processor are unable to meet the
 increasing application needs


Some Microcontrollers (like Automotive AVR, USB AVR from Atmel), System on
Processors etc are examples of Application Specific Instruction Set
Chips, Digital Signal
 Processors (ASIPs)

 and on-chip peripherals, demanded by the application requirement,
ASIPs incorporate a processor
program and data memory

Digital Signal Processors (DSPs):

Powerful special purpose 8/16/32 bit microprocessors designed specifically to meet the
computational demands and power constraints of today's embedded audio, video, and
communications applications

Digital Signal Processors are 2 to 3 times faster than the general-purpose microprocessors
in signal processing applications

DSPs implement algorithms in hardware which speeds up the execution whereas general
purpose processors implement the algorithm in firmware and the speed of execution
depends primarily on the clock for the processors

DSP can be viewed as a microchip designed for performing high speed computational
operations for „addition‟, „subtraction‟, „multiplication‟ and „division‟
N SURESH, Dept. of ECE 77
 MRCET ECE ES UNIT-3 Notes

A typical Digital Signal Processor incorporates the following key units

 
 Program Memory
 
Data Memory

 
Computational Engine

 
I/O Unit

Audio video signal processing, telecommunication and multimedia applications are

typical examples where DSP is employed

RISC V/s CISC Processors/Controllers:

RISC CISC
Lesser no. of instructions Greater no. of Instructions
Instruction Pipelining and increased execution Generally no instruction pipelining feature
speed
Orthogonal Instruction Set (Allows each instruction Non Orthogonal Instruction Set (All instructions
to operate on any register and use any addressing are not allowed to operate on any register and
mode) use any addressing mode. It is instruction
specific)
Operations are performed on registers only, the Operations are performed on registers or
only memory operations are load and store memory depending on the instruction

Large number of registers are available Limited no. of general purpose registers
Programmer needs to write more code to execute a . A programmer can achieve the desired
task since the instructions are simpler ones functionality with a single instruction which in
turn provides the effect of using more simpler
single instructions in RISC
Single, Fixed length Instructions Variable length Instructions

Less Silicon usage and pin count More silicon usage since more additional
decoder logic is required to implement the
complex instruction decoding.
With Harvard Architecture Can be Harvard or Von-Neumann Architecture

N SURESH, Dept. of ECE 78

 MRCET ECE ES UNIT-3 Notes

Harvard V/s Von-Neumann Processor/Controller Architecture

The terms Harvard and Von-Neumann refers to the processor architecture design.

Microprocessors/controllers based on the Von-Neumann architecture shares a single

common bus for fetching both instructions and data. Program instructions and data are
stored in a common main memory

Microprocessors/controllers based on the Harvard architecture will have separate data

bus and instruction bus. This allows the data transfer and program fetching to occur
simultaneously on both buses

With Harvard architecture, the data memory can be read and written while the program
memory is being accessed. These separated data memory and code memory buses allow
one instruction to execute while the next instruction is fetched (“Pre-fetching”)

I/O CPU Memory

Program CPU Data Memory

Memory

Single shared Bus

Harvard V/s Von-Neumann Processor/Controller Architecture:

Harvard Architecture Von-Neumann Architecture

Separate buses for Instruction and Data fetching Single shared bus for Instruction and Data
fetching
Easier to Pipeline, so high performance can be Low performance Compared to Harvard
achieved Architecture
Comparatively high cost Cheaper
No memory alignment problems Allows self modifying codes†
Since data memory and program memory are Since data memory and program memory
stored physically in different locations, no are stored physically in same chip, chances
chances for accidental corruption of program for accidental corruption of program
memory memory

N SURESH, Dept. of ECE 79

MRCET ECE ES UNIT-3 Notes

Application Specific Integrated Circuit (ASIC):

A microchip designed to perform a specific or unique application. It is used as
replacement to conventional general purpose logic chips.

ASIC integrates several functions into a single chip and thereby reduces the system
development cost

Most of the ASICs are proprietary products. As a single chip, ASIC consumes very small
area in the total system and thereby helps in the design of smaller systems with high
capabilities/functionalities.

ASICs can be pre-fabricated for a special application or it can be custom fabricated by

using the components from a re-usable „building block‟ library of components for a
particular customer application

Fabrication of ASICs requires a non-refundable initial investment (Non Recurring

Engineering (NRE) charges) for the process technology and configuration expenses

If the Non-Recurring Engineering Charges (NRE) is born by a third party and the
Application Specific Integrated Circuit (ASIC) is made openly available in the market,
the ASIC is referred as Application Specific Standard Product (ASSP)

The ASSP is marketed to multiple customers just as a general-purpose product , but to a

smaller number of customers since it is for a specific application.

N SURESH, Dept. of ECE 80

MRCET ECE ES UNIT-3 Notes

Some ASICs are proprietary products , the developers are not interested in revealing the
internal details.

Programmable Logic Devices (PLDs):


Logic devices provide specific functions, including device-to-device interfacing, data
communication, signal processing, data display,  timing and control operations, and
 almost every other function a system must perform.


Logic devices can be classified into two broad categories - Fixed and Programmable. The
circuits in a fixed logic device are permanent, they perform one function or set of
 functions - once manufactured, they cannot be changed


Programmable logic devices (PLDs) offer customers a wide range of logic capacity,
features, speed, and voltage characteristics -and these devices can be re-configured to
 perform any number of functions at any time


Designers can use inexpensive software tools to quickly develop, simulate, and test their
logic designs in PLD based design. The design can be quickly programmed into a device,
 and immediately tested in a live circuit


PLDs are based onre-writable memory technology and the device is reprogrammed to
change the design

Programmable Logic Devices (PLDs) – CPLDs and FPGA

Field Programmable Gate Arrays (FPGAs) and Complex Programmable Logic Devices
(CPLDs) are the two major types of programmable logic devices

FPGA:
FPGA is an IC designed to be configured by a designer after manufacturing.

FPGAs offer the highest amount of logic density, the most features, and the highest
performance.

Logic gate is Medium to high density ranging from 1K to 500K system gates

N SURESH, Dept. of ECE 81

MRCET ECE ES UNIT-3 Notes

These advanced FPGA devices also offer features such as built-in hardwired processors
(such as the IBM Power PC), substantial amounts of memory, clock management
systems, and support for many of the latest, very fast device-to-device signaling
technologies

Figure: FPGA Architecture

These advanced FPGA devices also offer features such as built-in hardwired processors,
substantial amounts of memory, clock management systems, and support for many of the
latest, very fast device-to-device signaling technologies.

FPGAs are used in a wide variety of applications ranging from data processing and
storage, to instrumentation, telecommunications, and digital signal processing

CPLD:

A complex programmable logic device (CPLD) is a programmable logic device with
complexity between that of PALs and FPGAs, and architectural features of both.

CPLDs, by contrast, offer much smaller amounts of logic - up to about 10,000 gates.

CPLDs offer very predictable timing characteristics and are therefore ideal for critical
control applications.

N SURESH, Dept. of ECE Page 82

MRCET ECE ES UNIT-3 Notes

CPLDs such as the Xilinx CoolRunner series also require extremely low amounts of
power and are very inexpensive, making them ideal for cost-sensitive, battery-operated,
portable applications such as mobile phones and digital handheld assistants.

ADVANTAGES OF PLDs:

• PLDs offer customer much more flexibility during design cycle

• PLDSs do not require long lead times for prototype or production-the PLDs are already
on a distributor‟s self and ready for shipment

• PLDs do not require customers to pay for large NRE costs and purchase expensive mask
sets

• PLDs allow customers to order just the number of parts required when they need them.
allowing them to control inventory.

• PLDs are reprogrammable even after a piece of equipment is shipped to a customer.

• The manufacturers able to add new features or upgrade the PLD based products that are
in the field by uploading new programming file

Commercial off the Shelf Component (COTS):

A Commercial off-the-shelf (COTS) product is one which is used „as-is‟

COTS products are designed in such a way to provide easy integration and
interoperability with existing system components

N SURESH, Dept. of ECE Page 83

MRCET ECE ES UNIT-3 Notes

Typical examples for the COTS hardware unit are Remote Controlled Toy Car control
unit including the RF Circuitry part, High performance, high frequency microwave
electronics (2 to 200 GHz), High bandwidth analog-to-digital converters, Devices and
components for operation at very high temperatures, Electro-optic IR imaging arrays,
UV/IR Detectors etc

A COTS component in turn contains a General Purpose Processor (GPP) or Application

Specific Instruction Set Processor (ASIP) or Application Specific Integrated Chip
(ASIC)/Application Specific Standard Product (ASSP) or Programmable Logic Device
(PLD)

The major advantage of using COTS is that they are readily available in the market,
cheap and a developer can cut down his/her development time to a great extend.

There is no need to design the module yourself and write the firmware .

Everything will be readily supplied by the COTs manufacturer.

N SURESH, Dept. of ECE Page 84

MRCET ECE ES UNIT-3 Notes

Sensors & Actuators:

• Embedded system is in constant interaction with the real world

• Controlling/monitoring functions executed by the embedded system is achieved in

accordance with the changes happening to the Real World.

• The changes in the system environment or variables are detected by the sensors
connected to the input port of the embedded system.

• If the embedded system is designed for any controlling purpose, the system will produce
some changes in controlling variable to bring the controlled variable to the desired value.

• It is achieved through an actuator connected to the out port of the embedded system.

Sensor:
A transducer device which converts energy from one form to another for any
measurement or control purpose. Sensors acts as input device

Eg. Hall Effect Sensor which measures the distance between the cushion and magnet in
the Smart Running shoes from adidas

Example: IR, humidity , PIR(passive infra red) , ultrasonic , piezoelectric , smoke

sensors

N SURESH, Dept. of ECE Page 85

MRCET ECE ES UNIT-3 Notes

Actuator:

A form of transducer device (mechanical or electrical)

which converts signals to corresponding physical
action (motion). Actuator acts as an output device

Eg. Micro motor actuator which adjusts the position of

the cushioning element in the Smart Running shoes
from adidas

N SURESH, Dept. of ECE Page 86

MRCET ECE ESD UNIT-3 NOTES

Communication Interface:
• Communication interface is essential for communicating with various subsystems of the
embedded system and with the external world

• The communication interface can be viewed in two different perspectives; namely;

1. Device/board level communication interface (Onboard Communication Interface)

2. Product level communication interface (External Communication Interface)

1. Device/board level communication interface (Onboard Communication Interface):

The communication channel which interconnects the various components within an
embedded product is referred as Device/board level communication interface (Onboard
Communication Interface)

 Examples: Serial interfaces like I2C, SPI, UART, 1-Wire etc and Parallel bus interface

2. Product level communication interface (External Communication Interface):

The „Product level communication interface‟ (External Communication Interface) is

responsible for data transfer between the embedded system and other devices or modules. The
external communication interface can be either wired media or wireless media and it can be a
serial or parallel interface.

 Examples for wireless communication interface: Infrared (IR), Bluetooth (BT), Wireless
LAN (Wi-Fi), Radio Frequency waves (RF), GPRS etc.
 Examples for wired interfaces: RS-232C/RS-422/RS 485, USB, Ethernet (TCP-IP), IEEE
1394 port, Parallel port etc.

87
MRCET ECE ESD UNIT-3 NOTES

1. Device/board level or On board communication interfaces: The

Communication channel which interconnects the various components within an embedded
product is referred as Device/board level communication interface (Onboard Communication
Interface)

These are classified into

1.1 I2C (Inter Integrated Circuit) Bus
1.2 SPI (Serial Peripheral Interface) Bus
1.3 UART (Universal Asynchronous Receiver Transmitter)
1.4 1-Wires Interface

1.5 Parallel Interface

1 I2C (Inter Integrated Circuit) Bus:

Inter Integrated Circuit Bus (I2C - Pronounced „I square C‟) is a synchronous bi-directional half
duplex (one-directional communication at a given point of time) two wire serial interface
bus.The concept of I2C bus was developed by „Philips Semiconductors‟ in the early 1980‟s. The
original intention of I2C was to provide an easy way of connection between a
microprocessor/microcontroller system and the peripheral chips in Television sets.

88
MRCET ECE ESD UNIT-3 NOTES

The I2C bus is comprised of two bus lines, namely; Serial Clock – SCL and Serial Data – SDA.

SCL line is responsible for generating synchronization clock pulses and SDA is
responsible for transmitting the serial data across devices.I2C bus is a shared bus system to
which many number of I2C devices can be connected. Devices connected to the I2C bus can act
as either „Master‟ device or „Slave‟ device.
The „Master‟ device is responsible for controlling the communication by
initiating/terminating data transfer, sending data and generating necessary synchronization clock

pulses.
89
MRCET ECE ESD UNIT-3 NOTES

Slave devices wait for the commands from the master and respond upon receiving the
commands. Master and „Slave‟ devices can act as either transmitter or receiver. Regardless
whether a master is acting as transmitter or receiver, the synchronization clock signal is

generated by the „Master‟ device only.I2C supports multi masters on the same bus.
The sequence of operation for communicating with an I2C slave device is:
1. Master device pulls the clock line (SCL) of the bus to „HIGH‟
2. Master device pulls the data line (SDA) „LOW‟, when the SCL line is at logic
„HIGH‟ (This is the „Start‟ condition for data transfer)


3. Master sends the address (7 bit or 10 bit wide) of the „Slave‟ device to which it wants to
communicate, over the SDA line.
4. Clock pulses are generated at the SCL line for synchronizing the bit reception by the
slave device.
5. The MSB of the data is always transmitted first.
6. The data in the bus is valid during the „HIGH‟ period of the clock signal
7. In normal data transfer, the data line only changes state when the clock is low.

8. Master waits for the acknowledgement bit from the slave device whose address is sent on
the bus along with the Read/Write operation command.

90
MRCET ECE ESD UNIT-3 NOTES

9. Slave devices connected to the bus compares the address received with the address
assigned to them
10. The Slave device with the address requested by the master device responds by sending an
acknowledge bit (Bit value =1) over the SDA line
11. Upon receiving the acknowledge bit, master sends the 8bit data to the slave device over
SDA line, if the requested operation is „Write to device‟.
12. If the requested operation is „Read from device‟, the slave device sends data to the
master over the SDA line.
13. Master waits for the acknowledgement bit from the device upon byte transfer complete
for a write operation and sends an acknowledge bit to the slave device for a read
operation
14. Master terminates the transfer by pulling the SDA line „HIGH‟ when the clock line SCL
is at logic „HIGH‟ (Indicating the „STOP‟ condition).

91
MRCET ECE ESD UNIT-3 NOTES

1.2 Serial Peripheral Interface (SPI) Bus:

The Serial Peripheral Interface Bus (SPI) is a synchronous bi-directional full duplex four wire
serial interface bus. The concept of SPI is introduced by Motorola.SPI is a single master multi-
slave system.

It is possible to have a system where more than one SPI device can be master, provided
the condition only one master device is active at any given point of time, is satisfied.

SPI is used to send data between Microcontrollers and small peripherals such as shift
registers, sensors, and SD cards.


SPI requires four signal lines for communication. They are:
Master Out Slave In (MOSI): Signal line carrying the data from master to slave device. It is
also known as Slave Input/Slave Data In (SI/SDI)
Master In Slave Out (MISO): Signal line carrying the data from slave to master device. It is
also known as Slave Output (SO/SDO)

92
MRCET ECE ESD UNIT-3 NOTES

Serial Clock (SCLK): Signal line carrying the clock signals

Slave Select (SS): Signal line for slave device select. It is an active low signal.
The master device is responsible for generating the clock signal.
Master device selects the required slave device by asserting the corresponding slave devices
slave select signal „LOW‟.
 The data out line (MISO) of all the slave devices when not selected floats at high impedance
state
 The serial data transmission through SPI Bus is fully configurable.
 SPI devices contain certain set of registers for holding these configurations.
 The Serial Peripheral Control Register holds the various configuration parameters like
master/slave selection for the device, baudrate selection for communication, clock signal
control etc.
 The status register holds the status of various conditions for transmission and reception.SPI
works on the principle of „Shift Register‟.
 The master and slave devices contain a special shift register for the data to transmit or
receive.
 The size of the shift register is device dependent. Normally it is a multiple of 8.

 During transmission from the master to slave, the data in the master‟s shift register is
shifted out to the MOSI pin and it enters the shift register of the slave device through the
MOSI pin of the slave device.

93
MRCET ECE ESD UNIT-3 NOTES

 At the same time the shifted out data bit from the slave device’s shift register enters the
shift register of the master device through MISO pin

I2C V/S SPI:

94
MRCET ECE ESD UNIT-3 NOTES

PARALLEL COMMUNICATION:
In data transmission, parallel communication is a method of conveying multiple binary
digits (bits) simultaneously. It contrasts with communication. The communication channel is the
number of electrical conductors used at the physical layer to convey bits.
Parallel communication implies more than one such conductor. For example, an 8-bit
parallel channel will convey eight bits (or a byte) simultaneously, whereas a serial channel would
convey those same bits sequentially, one at a time. Parallel communication is and always has
been widely used within integrated circuits, in peripheral buses, and in memory devices such as
RAM.

2. Product level communication interface (External Communication

Interface): The Product level communication interface‟ (External Communication Interface) is

responsible for data transfer between the embedded system and other devices or modules

It is classified into two types

1. Wired communication interface
2. Wireless communication interface:

1. Wired communication interface: Wired communication interface is an interface used to

transfer information over a wired network.

It is classified into following types.

1. RS-232C/RS-422/RS 485

2. USB

95
MRCET ECE ESD UNIT-3 NOTES

RS-232C:
 RS-232 C (Recommended Standard number 232, revision C from the Electronic Industry
Association) is a legacy, full duplex, wired, asynchronous serial communication interface
 RS-232 extends the UART communication signals for external data communication.
 UART uses the standard TTL/CMOS logic (Logic „High‟ corresponds to bit value 1 and
Logic „LOW‟ corresponds to bit value 0) for bit transmission whereas RS232 use the
EIA standard for bit transmission.
 As per EIA standard, a logic „0‟ is represented with voltage between +3 and +25V and a
logic „1‟ is represented with voltage between -3 and -25V.
 In EIA standard, logic „0‟ is known as „Space‟ and logic „1‟ as „Mark‟.

The RS232 interface define various handshaking and control signals for communication
apart from the „Transmit‟ and „Receive‟ signal lines for data communication
RS-232 supports two different types of connectors, namely; DB-9: 9-Pin connector and DB-25:
25-Pin connector.

96
MRCET ECE ESD UNIT-3 NOTES

Fig: DB-25:25-Pin connector.

Fig: DB-9:9-Pin connector.

97
MRCET ECE ESD UNIT-3 NOTES

 RS-232 is a point-to-point communication interface and the devices involved in RS-232

communication are called „Data Terminal Equipment (DTE)‟ and „Data Communication
Equipment (DCE)‟.
 If no data flow control is required, only TXD and RXD signal lines and ground line (GND)
are required for data transmission and reception.
 The RXD pin of DCE should be connected to the TXD pin of DTE and vice versa for proper
data transmission.
 If hardware data flow control is required for serial transmission, various control signal lines
of the RS-232 connection are used appropriately.
 The control signals are implemented mainly for modem communication and some of them
may be irrelevant for other type of devices.
 The Request to Send (RTS) and Clear To Send (CTS) signals co-ordinate the communication
between DTE and DCE.
 Whenever the DTE has a data to send, it activates the RTS line and if the DCE is ready to
accept the data, it activates the CTS line.
 The Data Terminal Ready (DTR) signal is activated by DTE when it is ready to accept data.
 The Data Set Ready (DSR) is activated by DCE when it is ready for establishing a
communication link.
 DTR should be in the activated state before the activation of DSR.
 The Data Carrier Detect (DCD) is used by the DCE to indicate the DTE that a good signal is
being received.

98
MRCET ECE ESD UNIT-3 NOTES

 Ring Indicator (RI) is a modem specific signal line for indicating an incoming call on the
telephone line.
 As per the EIA standard RS-232 C supports baudrates up to 20Kbps (Upper limit 19.2Kbps).
 The commonly used baudrates by devices are 300bps, 1200bps, 2400bps, 9600bps,
11.52Kbps and 19.2Kbps.
 The maximum operating distance supported in RS-232 communication is 50 feet at the
highest supported baudrate.
 Embedded devices contain a UART for serial communication and they generate signal levels
conforming to TTL/CMOS logic.
 A level translator IC like MAX 232 from Maxim Dallas semiconductor is used for converting
the signal lines from the UART to RS-232 signal lines for communication.
 On the receiving side the received data is converted back to digital logic level by a converter
IC.
 Converter chips contain converters for both transmitter and receiver.
 RS-232 uses single ended data transfer and supports only point-to-point communication and
not suitable for multi-drop communication.

USB (UNIVERSAL SERIAL BUS):

 External Bus Standard.

 Allows connection of peripheral devices.
 Connects Devices such as keyboards, mice, scanners, printers, joysticks, audio
devices, disks.
 Facilitates transfers of data at 480 (USB 2.0 only), 12 or 1.5 Mb/s (mega-
bits/second).
 Developed by a Special Interest Group including Intel, Microsoft, Compact, DEC,
IBM, Northern Telecom and NEC originally in 1994.
 Low-Speed: 10 – 100 kb/s
 1.5 Mb/s signaling bit rate
 Full-Speed: 500 kb/s – 10 Mb/s 12 Mb/s signaling bit rate
 High-Speed: 400 Mb/s

99
MRCET ECE ESD UNIT-3 NOTES

 480 Mb/s signaling bit rate

 NRZI with bit stuffing used

 SYNC field present for every packet

 There exist two pre-defined connectors in any USB system - Series “A” and Series “B”
Connectors.

 Series “A” cable: Connects USB devices to a hub port.

 Series “B” cable: Connects detachable devices (hot- swappable)

Bus Topology:

 Connects computer to peripheral devices.

 Ultimately intended to replace parallel and serial ports
 Tiered Star Topology
 All devices are linked to a common point referred to as the root hub.
7
 Specification allows for up to 127 (2 -1) different devices.

 Four wire cable serves as interconnect of system - power, ground and two differential
signaling lines.
 USB is a polled bus-all transactions are initiated by host.

100
MRCET ECE ESD UNIT-3 NOTES

USB HOST: Device that controls entire system usually a PC of some form. Processes data
arriving to and from the USB port.

USB HUB: Tests for new devices and maintains status information of child devices.Serve as
repeaters, boosting strength of up and downstream signals. Electrically isolates devices from one
another - allowing an expanded number of devices.
2.Wireless communication interface : Wireless communication interface is an interface used to
transmission of information over a distance without help of wires, cables or any other forms of
electrical conductors.

They are basically classified into following types

1. Infrared
2. Bluetooth
3. Wi-Fi
4. Zigbee
5. GPRS

INFRARED:

 Infrared is a certain region in the light spectrum

 Ranges from .7µ to 1000µ or .1mm

 Broken into near, mid, and far infrared

 One step up on the light spectrum from visible light

 Measure of heat

Most of the thermal radiation emitted by objects near room temperature is infrared. Infrared
radiation is used in industrial, scientific, and medical applications. Night-vision devices using
active near-infrared illumination allow people or animals to be observed without the observer
being detected.

101
MRCET ECE ESD UNIT-3 NOTES

IR transmission:
The transmitter of an IR LED inside its circuit, which emits infrared light for every electric pulse
given to it. This pulse is generated as a button on the remote is pressed, thus completing the
circuit, providing bias to the LED.

The LED on being biased emits light of the wavelength of 940nm as a series of pulses,
corresponding to the button pressed. However since along with the IR LED many other sources
of infrared light such as us human beings, light bulbs, sun, etc, the transmitted information can be
interfered. A solution to this problem is by modulation. The transmitted signal is modulated using
a carrier frequency of 38 KHz (or any other frequency between 36 to 46 KHz). The IR LED is
made to oscillate at this frequency for the time duration of the pulse. The information or the light
signals are pulse width modulated and are contained in the 38 KHz frequency.

IR supports data rates ranging from 9600bits/second to 16Mbps

Serial infrared: 9600bps to 115.2 kbps

Medium infrared: 0.576Mbps to 1.152 Mbps

Fast infrared: 4Mbps

BLUETOOTH:

Bluetooth is a wireless technology standard for short distances (using short-wavelength UHF
band from 2.4 to 2.485 GHz)for exchanging data over radio waves in the ISM and mobile
devices, and building personal area networks (PANs).Invented by telecom vendor Ericsson in
1994, it was originally conceived as a wireless alternative to RS- 232 data cables.

102
MRCET ECE ESD UNIT-3 NOTES

Bluetooth uses a radio technology called frequency- hopping spread spectrum. Bluetooth
divides transmitted data into packets, and transmits each packet on one of 79 designated
Bluetooth channels. Each channel has a bandwidth of 1 MHz. It usually performs 800 hops per
second, with Adaptive Frequency-Hopping (AFH) enabled

Originally, Gaussian frequency-shift keying (GFSK) modulation was the only modulation
scheme available. Since the introduction of Bluetooth 2.0+EDR, π/4-DQPSK (Differential
Quadrature Phase Shift Keying) and 8DPSK modulation may also be used between compatible
devices. Bluetooth is a packet-based protocol with a master- slave structure. One master may
communicate with up to seven slaves in a piconet. All devices share the master's clock. Packet
exchange is based on the basic clock, defined by the master, which ticks at312.5 µs intervals.

A master BR/EDR Bluetooth device can communicate with a maximum of seven devices
in a piconet (an ad-hoc computer network using Bluetooth technology), though not all devices
reach this maximum. The devices can switch roles, by agreement, and the slave can become the
master (for example, a headset initiating a connection to a phone necessarily begins as master—
as initiator of the connection—but may subsequently operate as slave).

Wi-Fi:
 Wi-Fi is the name of a popular wireless networking technology that uses radio waves to
provide wireless high-speed Internet and network connections
 Wi-Fi follows the IEEE 802.11 standard
 Wi-Fi is intended for network communication and it supports Internet Protocol (IP) based
communication
 Wi-Fi based communications require an intermediate agent called Wi-Fi router/Wireless
Access point to manage the communications.
 The Wi-Fi router is responsible for restricting the access to a network, assigning IP address to
devices on the network, routing data packets to the intended devices on the network.

103
MRCET ECE ESD UNIT-3 NOTES

 Wi-Fi enabled devices contain a wireless adaptor for transmitting and receiving data in
the form of radio signals through an antenna.
 Wi-Fi operates at 2.4GHZ or 5GHZ of radio spectrum and they co-exist with other ISM
band devices like Bluetooth.
 A Wi-Fi network is identified with a Service Set Identifier (SSID). A Wi-Fi device can
connect to a network by selecting the SSID of the network and by providing the
credentials if the network is security enabled
 Wi-Fi networks implements different security mechanisms for authentication and data
transfer.
 Wireless Equivalency Protocol (WEP), Wireless Protected Access (WPA) etc are some of
the security mechanisms supported by Wi-Fi networks in data communication.

ZIGBEE:

Zigbee is an IEEE 802.15.4-based specification for a suite of high- level communication

protocols used to create personal area networks with small, low-power digital radios, such as for
home automation, medical device data collection, and other low-power low-bandwidth needs,
designed for small scale projects which need wireless connection.Hence, zigbee is a low-power,
low data rate, and close proximity (i.e., personal area) wireless ad hoc network.The technology

104
MRCET ECE ESD UNIT-3 NOTES

defined by the zigbee specification is intended to be simpler and less expensive than other
wireless personal area networks (WPANs), such as Bluetooth or Wi-Fi . Applications include
wireless light switches, electrical meters with in-home-displays, traffic management systems, and
other consumer and industrial equipment that require short-range low- rate wireless data transfer.
Its low power consumption limits transmission distances to 10– 100 meters line-of-sight,
depending on power output and environmental characteristics. Zigbee devices can transmit data
over long distances by passing data through a mesh network of intermediate devices to reach
more distant ones.

Zigbee Coordinator: The zigbee coordinator acts as the root of the zigbee network. The ZC is
responsible for initiating the Zigbee network and it has the capability to store information about
the network.

Zigbee Router: Responsible for passing information from device to another device or to another
ZR.

Zigbee end device:End device containing zigbee functionality for data communication. It can
talk only with a ZR or ZC and doesn’t have the capability to act as a mediator for transferring
data from one device to another.

Zigbee supports an operating distance of up to 100 metres at a data rate of 20 to 250 Kbps.

105
MRCET ECE ESD UNIT-3 NOTES

General Packet Radio Service(GPRS):

General Packet Radio Service (GPRS) is a packet oriented mobile data service on the 2G and
3G cellular communication system's global system for mobile communications (GSM).GPRS
was originally standardized by European Telecommunications Standards Institute (ETSI) GPRS
usage is typically charged based on volume of data transferred, contrasting with circuit switched
data, which is usually billed per minute of connection time. Sometimes billing time is broken
down to every third of a minute. Usage above the bundle cap is charged per megabyte, speed
limited, or disallowed.

Services offered:

 GPRS extends the GSM Packet circuit switched data capabilities and makes the
following services possible:
 SMS messaging and broadcasting
 "Always on" internet access
 Multimedia messaging service (MMS)
 Push-to-talk over cellular (PoC)
 Instant messaging and presence-wireless village Internet applications for smart devices
through wireless application protocol (WAP).
 Point-to-point (P2P) service: inter-networking with the Internet (IP).
 Point-to-multipoint (P2M) service]: point-to- multipoint multicast and point-to-multipoint
group calls.

Text Book:-

1. Introduction to Embedded Systems – Shibu K.V Mc Graw Hill

106