AD
Яндекс Игры
Unblocked
AD
home.rosinka.ru
Rosinka Residences – House rental in
Moscow from 1 month
Index Isuzu Isuzu Trooper - service
repair manual 1998-2002 year
Search
КЛАМА
Content .. 607 608 609 610 ..
Isuzu Trooper (1998-2002 year). Manual - part 609
video-shoper.ru
mobo Full 6E–84 4JX1–TC ENGINE DRIVEABILITY AND EMISSIONS
Cover. Diagnostic Trouble Code (DTC) P0193 (Flash DTC 63)
2 590 ₽ Rail Pressure Sensor High Voltage
Узнать больше
060RW135
Circuit Description Diagnostic Aids
The rail pressure (RP) sensor responds to changes in oil Check for the following conditions:
manifold pressure. D Poor connection at ECM – Inspect harness connectors
The ECM monitors the RP signals for voltages outside the for backed-out terminals, improper mating, broken
normal range of the RP sensor. If the ECM detects a RP locks, improperly formed or damaged terminals, and
poor terminal-to-wire connection.
signal voltage that is excessively high, DTC P0193 will be
set. D Damaged harness – Inspect the wiring harness for
damage. If the harness appears to be OK, observe the
RP display on the Tech 2 while moving connectors and
Action Taken When the DTC Sets wiring harnesses related to the sensor. A change in the
D The ECM will store conditions which were present display will indicate the location of the fault.
when the DTC was set as Freeze Frame and in the If DTC P0193 cannot be duplicated, the information
Failure Records data.
included in the Failure Records data can be useful in
determining vehicle mileage since the DTC was last set. If
Conditions for Clearing the MIL/DTC it is determined that the DTC occurs intermittently,
D DTC P0193 can be cleared by using the Tech 2 “Clear performing the DTC P0193 Diagnostic Chart may isolate
Info” function or by disconnecting the ECM battery the cause of the fault.
feed.
4JX1–TC ENGINE DRIVEABILITY AND EMISSIONS 6E–85
DTC P0193 – RP Sensor High Voltage
Step Action Value(s) Yes No
1 Was the “On-Board Diagnostic (OBD) System Check” Go to OBD
performed? System
— Go to Step 2 Check
2 1. Ignition “ON,” engine “OFF.”
2. Review and record Tech 2 Failure Records data.
3. Operate the vehicle within Failure Records
conditions as noted.
4. Using a Tech 2, monitor “ DTC” info for DTC P0108. Refer to
Does the Tech 2 indicate DTC P0108 failed this Diagnostic
ignition? — Go to Step 3 Aids
3 Check the RP sensor signal circuit.
Replace the
Was the RP sensor signal circuit open or darmage? — RP circuit Go to Step 4
4 Probe the sensor ground circuit with a test light to B+.
Is the test light “ON?” — Go to Step 5 Go to Step 7
5 1. Check the RP signal circuit for a short to voltage or a
short to the 5 volt reference “J1” circuit.
2. If the RP sensor signal circuit is shorted, repair
circuit as necessary.
Was the RP sensor signal circuit shorted? — Verify repair Go to Step 6
6 1. Check for a poor sensor ground terminal connection
at the RP sensor electrical connector.
2. If a problem if found, replace the faulty terminal.
Did the terminal require replacement? — Verify repair Go to Step 7
7 1. Check for a poor sensor ground terminal connection
at the ECM.
2. If a problem is found, replace the faulty terminal.
Did the terminal require replacement? — Verify repair Go to Step 8
8 1. Check the continuity of the RP sensor ground
circuit.
2. If the RP sensor ground circuit measures over 5
ohms, repair open or poor connection.
Was a condition found and corrected? — Verify repair Go to Step 9
9 Replace the ECM (Refer to the Data Programming in
Case of ECM change).
Is the action complete? — Verify Repair —
6E–86 4JX1–TC ENGINE DRIVEABILITY AND EMISSIONS
Diagnostic Trouble Code (DTC) P1193 (Flash DTC 64)
RPCV Circuit Open/Short
060RW135
Circuit Description Diagnostic Aids
The rail pressure control valve (RPCV) is built in the high Check for the following conditions:
pressure oil circuit. D Poor connection at ECM – Inspect harness connectors
RPCV is an important device which is used to control oil for backed-out terminals, improper mating, broken
pressure in the HEUI system. locks, improperly formed or damaged terminals, and
poor terminal-to-wire connection.
The circuit receives current through Engine 15A fuse from
the battery, current flowing in the order of RPCV. D Damaged harness – Inspect the wiring harness for
damage. If the harness appears to be OK, observe the
RPCV display on the Tech 2 while moving connectors
Action Taken When the DTC Sets and wiring harnesses related to the RPCV. A change
D The ECM will store conditions which were present in the RPCV display will indicate the location of the
when the DTC was set as Freeze Frame and in the fault.
Failure Records data.
If DTC P1193 cannot be duplicated, the information
included in the Failure Records data can be useful in
Conditions for Clearing the MIL/DTC determining vehicle mileage since the DTC was last set.
D DTC P1193 can be cleared by using the Tech 2 “Clear If it is determined that the DTC occurs intermittently.
Info” function or by disconnecting the ECM battery
feed.
4JX1–TC ENGINE DRIVEABILITY AND EMISSIONS 6E–87
DTC P1193 – RPCV Circuit Open/Short
Step Action Value(s) Yes No
1 Was the “On-Board Diagnostic (OBD) System Check” Go to OBD
performed? System
— Go to Step 2 Check
2 1. Ignition “ON,” engine “ON.”
2. Observe the “Rail Oil Pressure” display on the Tech
2.
∼
Is the “Rail Oil Pressure” below the specified value? 3.5 5 Mpa Go to Step 4 Go to Step 3
3 Replace the RPCV.
Is the action complete? — Go to Step 2 —
4 1. Engine “On”.
2. Using the Tech 2, operate “RPCV”.
3. Check the combustion noise.
Was the combustion noise change? — — Go to Step 5
5 Check the RPCV circuit. (Fuse 15A to J1-14)
Was the RPCV circuit damaged? — Go to Step 6 Go to Step 7
6 Repair the RPCV circuit.
Is the action complete? — Verify repair —
7 Replace the ECM (Refer to the Data Programming in
Case of ECM change).
Is the action complete? — Verify repair Go to Step 8
8 Replace the high pressure oil pump.
Is the action complete? — Verify repair —
Content .. 607 608 609 610 ..
