NOTES

1. THIS DRAWING IS TO BE READ IN CONJUNCTION WITH ALL ENGINEERS &

ARCHITECT'S DRAWINGS.FIGURED DIMENSIONS ONLY (NOT SCALING) TO
FOOTPATH / ROAD SURFACE 1. ALL DIMENSIONS ARE IN MILLIMETERS (mm) UNLESS NOTED OTHERWISE BE USED. WHERE A CONFLICT OF INFORMATION EXISTS OR IF IN ANY
2. THE MINIMUM DEPTH OF COVER FROM THE FINISHED SURFACE TO THE DOUBT - `ASK'.
CROWN OF GRAVITY PIPES WITHOUT PROTECTION SHOULD BE AS BITUMINOUS CLASS D 400 (IS EN 124) C.I.
BACKFILL REFER TO FOLLOWS : SEALANT GULLY GRATING & FRAME 2. CONSULTANTS TO BE INFORMED IMMEDIATELY OF ANY DISCREPANCIES
A) GARDENS AND PATHWAYS WITHOUT ANY POSSIBILITY OF VEHICULAR BEDDED IN MORTAR FINISH AS SPECIFIED

SEE NOTE 2.
NOTE 3 FOR DETAILS BEFORE WORK PROCEEDS.
ACCESS - DEPTH NOT LESS THAN 0.5 M . ( THIS WOULD NORMALLY RELATE
MARKER TAPE REFER TO DRAINS IN PRIVATE PROPERTY . SHALLOW PIPES OF THIS NATURE ARE CROSS FALL
TO NOTE 9 FOR 3. WASTE DRAINAGEDETAILS TO BE IN ACCORDANCE WITH IRISH WATER
UNDESIRABLE AND SHOULD BE INSTALLED IN ACCORDANCE WITH THE REQUIREMENTS UNLESS NOTED OTHERWISE.
DETAILS CURRENT BUILDING REGULATIONS ) . REFER TO IRISH WATER DETAILS FOR ADDITIONAL INFORMATION.

300
B) DRIVEWAYS, PARKING AREAS AND YARDS WITH HEIGHT RESTRICTIONS TO
PREVENT ENTRY BY VEHICLES WITH A GROSS VEHICLE WEIGHT IN EXCESS 4. REFER TO THE STRUCTURAL WATERMAIN DETAILS DRAWING FOR A
OF 7.5 TONNES - DEPTH NOT LESS THAN 0.75 M . CHAIN TYPICAL SERVICE LAYOUT UNDER A FOOTPATH
C) DRIVEWAYS, PARKING AREAS AND NARROW STREETS WITHOUT
PIPE BEDDING REFER FOOTWAYS ( E.G.MEWS DEVELOPMENTS ) WITH LIMITED ACCESS FOR RODDING EYE FIXED 150Ø PIPE AT NOT LESS THAN
TO NOTE 5 FOR WITH STOPPER AND
ON/ 4 OR 200 MIN.

VEHICLES WITH A GROSS VEHICLE WEIGHT IN EXCESS OF 7.5 TONNES 1:100 FALL ENCASED IN 150 MIN. 5. CONNECTION OF BRANCHES TO THE MAIN LINE ARE TO BE BY
BUT SEE TABLE

DETAILS - DEPTH NOT LESS THAN 0.9 M . GALVANIZED C16/20 MIX CONCRETE WHERE MEANS OF 45° BRANCH CONNECTIONS, SADDLE CONNECTIONS
D) DEPTHS OF SEWERS IN GATED ESTATES SHALL BE SIMILAR TO THAT D 450Ø PRECAST COVER IS LESS THAN 1.2m NOT ALLOWED.
OUTLINED ABOVE .
C

CONCRETE GULLY
E) AGRICULTURAL LAND AND PUBLIC OPEN SPACE - DEPTH NOT LESS THAN TO COMPLY WITH IS EN 1917 6. INTERNAL GROUND FLOOR FOUL CONNECTIONS TO DRAIN

450 MIN.
0.9 M . SEPARATELY FROM THE UPPER STOREYS.
PIPE DIA. F) OTHER HIGHWAYS AND PARKING AREAS WITH UNRESTRICTED ACCESS TO
450 Ø 150mm C16/20 MIX CONCRETE
-'A' VEHICLES WITH A GROSS VEHICLE WEIGHT IN EXCESS OF 7.5 TONNES - 7. ALL BURIED PIPES UNDER GROUND FLOOR SLABS TO BE
DEPTH NOT LESS THAN 1.2 m . IF THE MINIMUM COVERS LISTED ABOVE ARE NOT SURROUND TO SADDLE
ENCASED IN CONCRETE.
ACHIEVED THE PIPES ARE TO BE FULLY ENCASED IN CONCRETE AS PER DETAIL B2. CONNECTION OF GULLY
MINIMUM TRENCH
WIDTH - 'B' 3. CLAUSE 808 MATERIAL IN ACCORDANCE WITH THE TII SPECIFICATION FOR SPUR LINE INTO MAIN
8. ALL GULLY GRATINGS AND LIDS TO BE MIN. D400
ON+400 MIN. BUT SEE TABLE) ROAD WORKS IS TO BE USED AS BACKFILL MATERIAL WHERE THE SEWER MAIN TRENCHES FOR PIPES NEAR FOUNDATIONS STORMWATER LINE
GULLY ENCASED IN RATING.

X
IS LOCATED IN ROADS, FOOTPATHS OR WHEN THE NEAREST PART OF THE TO BE EXCAVATED IN SHORT SECTIONS TO AVOID 150mm C16/20 MIX CONCRETE
TRENCH IS WITHIN 1 m OF THE PAVED EDGE OF THE ROADWAY. UNDERMINING OF FOUNDATIONS. EXCAVATION,
CLAUSE 808 IS TO BE COMPACTED AS PER CLAUSE 802 OF THE TII PIPELAYING AND CONCRETE BACKFILL TO
A1 CROSS SECTION IN PAVED AREAS SPECIFICATION FOR ROAD WORKS . BE CARRIED OUT ON THE SAME DAY. CONTRACTOR 150 150
-
4. SELECTED EXCAVATED MATERIAL (eg. CLASS 2C MATERIAL TO TABLE 6.1 TO SUBMIT METHOD STATEMENT FOR REVIEW BY
OF TII SPECIFICATION FOR ROADWORKS) MAY BE USED IN GREEN - THE ENGINEER PRIOR TO EXCAVATION
NOTE:

150
FIELD AREAS ABOVE GRANULAR PIPE SURROUND MATERIAL SUBJECT TO THE BEING CARRIED OUT.
APPROVAL OF THE EMPLOYERS REPRESENTATIVE .
1. FORM A SAW CUT 100mm DEEP AT A MIN. OF 100mm FROM SIDES OF EXCAVATION
5. PIPE BEDDING SHALL COMPLY WITH WIS 4-08-02 AND IGN 4-08-01 GRANULAR
MATERIAL SHALL BE 14 mm TO 5 mm GRADED AGGREGATE OR 10 mm WHERE 'D' IS LESS THAN 2X PRIOR TO PERMANENT REINSTATEMENT. WHERE ANY TRIM LINES ARE WITHIN E1 PRECAST ROAD GULLY
(CONCRETE FILL TO LEVEL OF FOUNDATION BOTTOM) 400mm OF ROAD EDGE, JOINT OR OTHER REINSTATEMENT, THE TRIM LINE SHOULD -
SINGLE SIZED AGGREGATE IS EN 13242 CONCRETE BED , HAUNCH &
BE EXTENDED TO THE INTERFACE OF SUCH SITUATIONS.
SURROUND WHERE REQUIRED (NOTE: CONCRETE BED AND HAUNCH 150 150
REQUIRED IN AREAS TO BE TAKEN IN CHARGE BY DUBLIN CITY
DEPTH OF COUNCIL) , SHALL BE TO DETAIL B1.
6. IN SOFT GROUND CONDITIONS ( CBR < 5 ) THE MATERIAL SHOULD BE
C DRAIN LAID NEAR FOUNDATIONS 2. LEAN-MIX SURFACE TO BE SPRAYED AS PER CLAUSE 920 (TII SPEC.) PRIOR TO
APPLICATION OF BINDER COURSE MACADAM.
REINSTATED TOPSOIL -
TO MATCH EXISTING EXCAVATED AND DISPOSED OF IN ACCORDANCE WITH THE WASTE
3. 100°C HOT BITUMEN BINDER 50 PEN OR COLD THIXOTROPIC BITUMEN 50 - 70 PEN
GRASSED AREAS MANAGEMENT ACT AND CLAUSE 808 MATERIAL IN ACCORDANCE WITH THE
SELECTED BACKFILL TO BE APPLIED TO ALL VERTICAL CUTS IN ACCORDANCE WITH IS EN 13108-4 PRIOR
TII SPECIFICATION FOR ROAD WORKS SHALL REPLACE THE EXCAVATED MATERIAL,
REFER TO NOTE 4 TO APPLICATION OF BITUMINOUS MATERIAL.
WRAPPED IN GEO - TEXTILE WRAPPING . ALTERNATIVELY , SPECIAL PIPE SUPPORT
FOR DETAILS
SEE NOTE 2.

ARRANGEMENTS , INCLUDING PILING ETC . MAY BE REQUIRED WHERE THE DEPTH

4. JOINTS SEALED WITH HOT BITUMEN AND TOPPED WITH FINE SAND / GRIT TO GET A
OF SOFT MATERIAL IS EXCESSIVE.SUCH ARRANGEMENTS SHALL BE SUBJECT TO
MARKER TAPE REFER MINIMUM 55 SKID RESISTANCE VALUE AS DETERMINED BY THE PORTABLE SKID
ASSESSMENT BY THE EMPLOYERS REPRESENTATIVE BEFORE ADVANCING WITH
SEE NOTE 7.

TO NOTE 9 FOR DETAILS RESISTANCE PENDULUM USED IN ACCORDANCE WITH ROAD NOTE 27 AND SHALL
THE WORK .
VARIES

NOT EXCEED 3mm THICKNESS AND 25mm WIDTH.

7. IN GREEN FIELD AREAS , TYPE B BACKFILL ( SELECTED EXCAVATED
MATERIAL ) WILL BE ALLOWED ABOVE THE SIDE HAUNCH GRANULAR 5. SURFACE REINSTATEMENT CONCRETE KERB 320 MIN.
MATERIAL IN THE CASE OF RIGID PIPES . A GRANULAR SURROUND OF A ASPHALT CONCRETE ROAD -
MINIMUM DEPTH OF 150 mm ABOVE THE CROWN OF THE PIPE IS REQUIRED 150 150 40mm MIN THICK OF 'SMA 10 surf 70/100 des' SURFACE COURSE TO IS EN
FOR FLEXIBLE PIPES , AND TYPE B MATERIAL MAY BE USED AS BACKFILL 13108 and NSAI's S28; ON 60mm MIN THICK OF 'AC 20 dense bin 70 /100 des' GULLIES TO BE HINGED AT RIGHT

TRAFFIC DIRECTION
PIPE BEDDING REFER TO 1. ALL DIMENSIONS ARE IN MILLIMETERS (mm) UNLESS NOTED
ABOVE THIS . ALL RISING MAINS IN GREENFIELD AREAS SHALL HAVE A BINDER COURSE TO IS EN 13108 AND NSAI's S28; ON BITUMEN SPRAY TO ANGLES TO KERB LINE SO THEY
NOTE 5 FOR DETAILS OTHERWISE.
ON/ 4 OR 200 MIN.

150
CLOSE WITH DIRECTION OF TRAFFIC
BUT SEE TABLE

MINIMUM COVER OF 300 mm OF GRANULAR MATERIAL ABOVE THE Cl.920 OF TII SPECIFICATION FOR ROAD WORKS ON 225mm THICK LEAN

450 MIN.
EXTERNAL CROWN OF THE PIPE . MIX CONCRETE. SAW CUT AND REINSTATE TO 100mm FROM EDGE OF WITH SLOTS AT RIGHT ANGLES TO KERB.
2. CONCRETE PIPE BEDS AND HAUNCHES MAY BE REQUIRED TO
8. PIPES SHALL NOT BE SUPPORTED ON STONES , ROCKS , OR ANY HARD TRENCH EXCAVATION. JOINTS SEALED WITH HOT BITUMEN AS NOTE 4
ADDRESS MINIMUM COVER SITUATIONS. AND SHALL BE SUBJECT TO
C

OBJECTS AT ANY POINT ALONG THE TRENCH . ROCK SHALL BE EXCAVATED

SUBMISSION AND ASSESSMENT BY THE EMPLOYERS
TO A DEPTH OF 150 mm BELOW THE ACTUAL DEPTH OF THE TRENCH WITH
REPRESENTATIVE BEFORE ADVANCING WITH THE WORKS.
PIPE DIA. THE VOID FILLED WITH CLAUSE 808 MATERIAL IN ACCORDANCE WITH THE
-'A' TII SPECIFICATION FOR ROAD WORKS . THE GRANULAR MATERIAL SHALL BE CLASS D 400 (IS EN 124) C.I.
3. CONCRETE PIPE BEDS AND HAUNCHES SHALL HAVE GULLY GRATING & FRAME
LAID ABOVE THIS VOID BACKFILL MATERIAL TEMPORARY BITMAC SEAL JOINTS WALLS CONSTRUCTED OF FINISH AS
MINIMUMTHICKNESS OF 150 mm WITH AN ABSOLUTE MINIMUM

150
9. NON DEGRADABLE MARKER TAPE SHOULD BE INSTALLED AT TOP OF PIPE 100 MIN. SEE NOTE 5 100 MIN. 215mm SOLID ENGINEERING BEDDED IN MORTAR SPECIFIED
DEPTH OF COVER ABOVE THE EXTERNAL CROWN OF THE PIPE OF SURFACE REINSTATEMENT SEE NOTE 4 BITUMINOUS
MINIMUM TRENCH BEDDING LAYER . . BRICKS WITH DESIGNATION
GRATING PLAN

40
150 mm . 125 mm THICK MINIMUM SEALANT
WIDTH - 'B' 10. TRENCH WIDTHS FOR PIPE SIZES 80 mm MAY BE < 500 mm , SUBJECT TO 1 MORTAR AND 1 COAT 10mm
(ON+400 MIN. BUT SEE TABLE) CONSIDERATION BEING GIVEN TO THE TRENCH DEPTH , HEALTH & SAFETY B1 CONCRETE BED & HAUNCH 4. CONCRETE TO BE IN ACCORDANCE WITH IS EN 206 AND TO BE PLASTER INTERNALLY OR
& CONSTRUCTION ACCESS REQUIREMENTS . - CLASS C 16 / 20. 225mm THICK MASS CONCRETE
EXTERNAL
DIAMETER 5. THE HAUNCHES AND SURROUNDS TO BE FORMED USING
A2 CROSS SECTION IN GRASSED AREAS 150 OF PIPE 150 FORMWORK TO PROVIDE A ROUGH CAST FINISH .

225

INVERT
370 TO
- LEAN MIX
/ SOFT LANDSCAPING 6. EXPANSION JOINTS IN THE CONCRETE SHALL BE PROVIDED AT ALL

60
CONCRETE
CL.808 AS PER

150
PIPE JOINTS TO ALLOW FOR PIPE FLEXIBILITY , COMPRESSIBLE

EXTERNAL DIAMETER
150Ø PIPE AT NOT LESS THAN

750 MIN.
FILLER BOARD TO BE IN ACCORDANCE WITH BS EN 622-1 AND BS EN STANDARD DETAIL A
BUT SEE NOTE 1:100 FALL ENCASED IN 150 MIN.
622-4. AND TO BE 18mm THICK .
* C16/20 MIX CONCRETE WHERE COVER

600 MINIMUM
7. POLYETHYLENE PIPES SHALL BE WRAPPED IN PLASTIC SHEETING IS LESS THAN 1.2m

450
HAVING A COMPOSITION IN ACCORDANCE WITH BS 6076 BEFORE CL.808 AS PER
BEING CAST INTO CONCRETE. STANDARD DETAIL A

OF PIPE
≤PIPE DIAMETER TRENCH WIDTH PIPE MATERIALS BUT SEE NOTE
*

150
A ( mm ) B ( mm ) 8. BITUMINOUS MATERIAL SHALL NOT BE PUT IN CONTACT WITH PE 150mm C16/20 MIX CONCRETE
UNLESS SPECIFICALLY NOTED OTHERWISE IN THE DRAINAGE LAYOUT THE PIPE OR PVC PIPES . SURROUND TO SADDLE CONNECTION
MATERIAL WILL BE AS FOLLOWS: OF GULLY SPUR LINE INTO MAIN
80 RISING MAIN SEE NOTE 10.

150
STORMWATER LINE
PIPE DIAMETER < 225mm: USE uPVC PIPE WORK B2 FULL CONCRETE PIPE BEDDING
100 500 150 300 MIN. 150
PIPE DIAMETER ≥225mm: USE CONCRETE PIPE WORK. - & COVER PIPE BEDDING
ENCASEMENT
150 600 PIPE MATERIAL TO BE IN ACCORDANCE WITH THE FOLLOWING: EXPANSION JOINT
WITH COMPRESSIBLE CONCRETE
PIPE SURROUND
AS PER STANDARD
DETAIL A
*
NOTE: TO AVOID STAGE
2 REPLACE CLAUSE 1808
& COVER
AS PER STANDARD
FILLER BOARD DETAIL A IN SITU MIX C25/30 CONCRETE
1. CONCRETE PIPES TO HAVE SPIGOT & SOCKET JOINTS AND RUBBER RING MATERIAL WITH LEAN
200 600 WITH A393 BOTTOM MESH
FITTINGS TO IS EN 1916 (2002); BS5911, PART 1 , (2002- 2010) AND IS 6 (2004), MIX CONCRETE REINFORCEMENT
250 750 STRENGTH CLASS 120 E2 BRICK ROAD GULLY
2. uPVC PIPES, JOINTS AND FITTINGS TO COMPLY WITH THE PROVISION OF IS EN 1401-

150
-

150
STAGE 1 STAGE 2

DIAMETER OF PIPE
300 750 PART 1 AND BS 4660 (NOTE: uPVC PIPES NOT PERMITTED IN AREAS TO BE
TAKEN IN CHARGE BY DUBLIN CITY COUNCIL) LEAVE FOR 6 MONTHS DIG OUT SURFACING & TOP 225mm OF CL808

EXTERNAL
750 FLOW FLOW TO CONSOLIDATE MATERIAL & REPLACE WITH NEW WIDER
350

450
SURFACING ON 225mm LAYER OF LEAN-MIX CONCRETE
400 900 SEE NOTE ABOVE FOR DETAILED METHOD STATEMENT 150 150

150
450 900

COMPRESSIBLE FILLER
A TRENCH BACKFILL & BEDDING SPIGOT AND SOCKET JOINT
D REINSTATEMENT OF PIPE E TYPICAL SECTION THROUGH ROAD GULLY
- -
TRENCH IN EXISTING ROAD -

B CONCRETE HAUNCH, BED & SURROUND

-

1. ALL DIMENSIONS ARE IN MILLIMETERS (mm) UNLESS NOTED OTHERWISE. 1. ALL DIMENSIONS ARE IN MILLIMETERS (mm) UNLESS NOTED OTHERWISE. 1. ALL DIMENSIONS ARE IN MILLIMETRES (mm) UNLESS NOTED OTHERWISE.
1. ALL DIMENSIONS ARE IN MILLIMETERS (mm) UNLESS NOTED OTHERWISE.
2. PRE-CAST MANHOLES UNITS : COMPLYING WITH REQUIREMENTS OF IS EN 2. IN-SITU MANHOLES TO HAVE A MINIMUM WALL AND FLOOR THICKNESS OF 2. RODDING EYE CHAMBER SHALL BE COVERED WITH APPROVED HEAVY
2. SOLID BLOCKWORK TO BE OF HIGH STRENGTH ( 20 N/mm) TO IS EN 771 .
3. MAXIMUM DEPTH OF BLOCK WORK MANHOLE IS 2.0 m ( THE USE 1917 AND BS 5911-PART 3 . 225mm FOR MANHOLE DEPTHS UP TO 3.0 m AND 300 mm OR MORE WHEN THE DUTY METAL COVERS TO IS 261 AND BS 5834. COVER AND FRAME SHALL
OF BLOCK WORK IN DEEPER MANHOLES WILL BE CONSIDERED 3. THICKER MANHOLE BASES REQUIRED FOR SEWERS IN EXCESS OF 3m DEEP MANHOLE DEPTH EXCEEDS 3.0 m . BE SUITABLE FOR ROAD AND TRAFFIC CONDITIONS AND IS SUBJECT TO GALVANISED IRON CHAIN
WHERE THE SIZE IS GREATER THAN THE STANDARD MINIMUM SIZE . 3. STRUCTURAL DESIGN & REINFORCEMENT DETAILS TO BE PROVIDED BY THE THE APPROVAL OF THE EMPLOYERS REPRESENTATIVE
BUT SUCH USE WILL REQUIRE DETAILED STRUCTURAL DESIGN
4. APPROVED PRE-CAST CONCRETE BASES MAY BE USED INCORPORATING DEVELOPER AND SUBMITTED TO THE EMPLOYERS REPRESENTATIVE 3. ALL CHAMBERS TO BE CHECKED FOR UPLIFT BY THE DEVELOPER BASED
AND WRITTEN APPROVAL FROM THE EMPLOYERS REPRESENTATIVE ) .
CHANNELS , BENCHING ETC. SUBJECT TO THE EMPLOYERS REPRESENTATIVE FOR REVIEW ON GROUND CONDITIONS WITHIN THE SITE. SHOULD ANTI FLOATATION
4. WALLS TO BE FLUSH POINTED INTERNALLY.
APPROVAL AND COMPLYING WITH BS 5911-PART 4 2002 . 4. MANHOLES GREATER THAN 3m IN DEPTH WILL REQUIRE A DETAILED MEASURES BE REQUIRED THEY SHALL BE SUBJECT TO APPROVAL
FOR FOUL MANHOLES PROVIDE, INTERNAL LINING OF ENGINEERING
5. STRUCTURAL DESIGN AND REINFORCEMENT DETAILS TO BE PROVIDED BY STRUCTURAL DESIGN AND BE SUBJECT TO THE EMPLOYERS FROM THE EMPLOYERS REPRESENTATIVE.
BRICK TO IS EN 771-1 TO A HEIGHT OF 1 m ABOVE BENCHING. ENGINEERING
THE DEVELOPER AND SUBMITTED TO THE EMPLOYERS REPRESENTATIVE REPRESENTATIVE APPROVAL . 4. ALL CONCRETE TO BE IN ACCORDANCE WITH IS EN 206.
BRICK TO BE BONDED TO BLOCK WORK USING ENGLISH GARDEN WALL BOND .
FOR REVIEW . 5. COVERS AND FRAMES SHALL BE SUITABLE FOR ROAD AND TRAFFIC 5. MANHOLE DETAILS TO BE IN ACCORDANCE WITH DETAILS F,G & H STOPPER RODDING ARM PROVIDES MEANS
5. STRUCTURAL DESIGN AND REINFORCEMENT DETAILS FOR ROOF AND BASE
6. MANHOLES GREATER THAN 3m IN DEPTH WILL REQUIRE A DETAILED CONDITIONS SUBJECT TO APPROVAL FROM THE EMPLOYERS OF ACCESS TO PORTION OF
SLABS TO BE PROVIDED BY THE CONTRACTOR AND SUBMITTED TO THE
STRUCTURAL DESIGN AND BE SUBJECT TO THE EMPLOYERS REPRESENTATIVE DRAIN BETWEEN TRAP AND SEWER
EMPLOYERS REPRESENTATIVE FOR REVIEW .
REPRESENTATIVES APPROVAL . 6. 200 mm ALL AROUND, 100 mm DEEP CONCRETE PLINTH WITH PROTECTIVE OR OTHER OUTFALL
6. COVERS AND FRAMES SHALL BE SUITABLE FOR ROAD AND TRAFFIC
7. MANHOLE ROOFS SHOULD CONSIST OF RE-INFORCED CONCRETE SLAB OF STAINLESS METAL BAND AROUND COVERS IN GREEN AREAS.
CONDITIONS SUBJECT TO APPROVAL FROM THE EMPLOYERS REPRESENTATIVE
.7. 200mm ALL AROUND, 100mm DEEP CONCRETE PLINTH WITH IN-SITU CONCRETE , C 30 / 37 ,WITH A MINIMUM THICKNESS OF 225mm. 7. ALL CHAMBERS TO BE IN CHECKED FOR UPLIFT BY THE CONTRACTOR, BASED ON HEAVY DUTY COVER
DESIGNED TO CARRY ALL LIVE AND DEAD LOADS, ALTERNATIVELY, GROUND CONDITIONS WITHIN THE SITE . SHOULD ANTI FLOTATION MEASURES BE AND FRAME D400
PROTECTIVE STAINLESS STEEL METAL BAND AROUND COVERS IN
APPROVED PRE-CAST CONCRETE ROOF SLABS MAY BE USED SUBJECT TO REQUIRED THEY SHALL BE SUBJECT TO APPROVAL FROM THE ER. (TO SUIT150 mm OPE. ) .
GREEN AREAS.
8. ALL CHAMBERS TO BE CHECKED FOR UPLIFT BY THE CONTRACTOR THE EMPLOYERS REPRESENTATIVES APPROVAL AND COMPLIANCE WITH BS 8. ALL CONCRETE TO BE IN ACCORDANCE WITH IS EN 206 : 2013 .
BASED ON GROUND CONDITIONS WITHIN THE SITE. SHOULD ANTI 5911 PART 4 : 2002. 9. BRANCH PIPES INTO MANHOLES: BENCHING TO BE SHAPED SO AS TO GUIDE THE
FLOW IN THE FLOW DIRECTION. THE MINIMUM LENGTH OF THE MANHOLE COVER TO BE SET AS
FLOATATION MEASURES BE REQUIRED THEY SHALL BE SUBJECT TO 8. COVERS AND FRAMES SHALL BE SUITABLE FOR ROAD AND TRAFFIC FLOW DIRECTION
BASED ON THE SIDE WITH THE GREATEST NUMBER OF BRANCHES EQUAL PER MANUFACTURER'S
APPROVAL FROM THE EMPLOYERS REPRESENTATIVE . CONDITIONS SUBJECT TO APPROVAL FROM THE EMPLOYERS
SPECIFICATION
9. ALL CONCRETE TO BE ACCORDANCE WITH IS EN 206: 2013 . REPRESENTATIVES TO 300mm PLUS THE SUM OF THE BRANCH DIAMETERS PLUS 200mm N1 INTERCEPTION TRAP DETAIL
10. BRANCH PIPES INTO MANHOLES: BENCHING TO BE SHAPED SO AS TO GUIDE THE .
9. 200 mm ALL AROUND, 100 mm DEEP CONCRETE PLINTH WITH PROTECTIVE PER BRANCH FOR BRANCHES UP TO 150mm (OR 300mm FOR -

STAINLESS METAL BAND AROUND COVERS IN GREEN AREAS. BRANCHES GREATER THAN 150mm DIAMETER). 150mm DIA. PVC PIPE CHAIN
FLOW IN THE FLOW DIRECTION. THE MINIMUM LENGTH OF THE MANHOLE SURFACE WATER DRAIN
BASED ON THE SIDE WITH THE GREATEST NUMBER OF BRANCHES EQUAL 10. ALL CHAMBERS TO BE CHECKED FOR UPLIFT BY THE CONTRACTOR, BASED ON 10. WHERE PIPE DIAMETER CHANGES AT A MANHOLE THE PIPE CROWNS ARE TO LINE UP THIS CONNECTION IS UNNECESSARY
TO 300mm PLUS THE SUM OF THE BRANCH DIAMETERS PLUS 200mm GROUND CONDITIONS WITHIN THE SITE . SHOULD ANTI FLOTATION MEASURES 11. MANHOLE SHAFTS ARE RECOMMENDED IN DEEP MANHOLES . THE DISTANCE BETWEEN THE 150mm CONCRETE IF THERE IS A SEPERATE SURFACE
BE REQUIRED THEY SHALL BE SUBJECT TO APPROVAL FROM THE EMPLOYERS TOP OF THE BENCHING AND THE SOFFIT OF THE MAIN ROOF SLAB SUPPORTING THE SOFFIT SURFACE WATER
PER BRANCH FOR BRANCHES UP TO 150mm (OR 300mm FOR SURROUND AND FOUL SYSTEM IN THE ROAD MANHOLE/ INSPECTION
BRANCHES GREATER THAN 150mm DIAMETER). REPRESENTATIVE SHOULD BE NOT LESS THAN 2.1m , THE MINIMUM SHAFT SIZE SHOULD BE 900mm. STOPPER
11. ALL CONCRETE TO BE IN ACCORDANCE WITH IS EN 206 : 2013 . 12. ALL MANHOLES TO BE WATERTIGHT TO THE SATISFACTION OF THE EMPLOYERS CHAMBER
11. WHERE PIPE DIAMETER CHANGES AT A MANHOLE THE PIPE CROWNS ARE TO LINE UP Y - JUNCTION
MANHOLE COVER AND ALL MANHOLES TO BE WATERTIGHT TO THE SATISFACTION OF THE EMPLOYERS 12. BRANCH PIPES INTO MANHOLES: BENCHING TO BE SHAPED SO AS TO GUIDE THE REPRESENTATIVE. THIS BECOMES THE LIVE
FOUL DRAIN
FRAME SHALL COMPLY TO REPRESENTATIVE FLOW IN THE FLOW DIRECTION. THE MINIMUM LENGTH OF THE MANHOLE CONNECTION IF A SURFACE
BASED ON THE SIDE WITH THE GREATEST NUMBER OF BRANCHES EQUAL 45° BEND 150 WATER SYSTEM IS IN THE ROAD
EN 124 AND BS 7903
( ALL CLASS D400 COVERS SHALL TO 300mm PLUS THE SUM OF THE BRANCH DIAMETERS PLUS 200mm FOUL
HAVE MIN. FRAME DEPTH 150 mm ) PER BRANCH FOR BRANCHES UP TO 150mm (OR 300mm FOR MANHOLE/
OPE. 600x600 mm . BRANCHES GREATER THAN 150mm DIAMETER). 150mm GRADE C 25 / 30 INSPECTION CHAMBER BLANKED OFF ENDS
1 NO. COURSE MIN.. 13. WHERE PIPE DIAMETER CHANGES AT A MANHOLE THE PIPE CROWNS ARE TO LINE UP MANHOLE COVER AND FRAME SHALL INTERCEPTING
COVER TO BE SET AS PER 3 NO. COURSES MAX OF CLASS B COMPLY TO IS EN 124 AND BS 7903 CONCRETE SURROUND TRAP
14. MANHOLE SHAFTS ARE RECOMMENDED IN DEEP MANHOLES . THE DISTANCE BETWEEN THE PROPERTY BOUNDARY
MANUFACTURER'S ENGINEERING BRICKS SET IN C 50/60 ( ALL CLASS D400 COVERS SHALL HAVE INTERCEPTING TRAP
TOP OF THE BENCHING AND THE SOFFIT OF THE MAIN ROOF SLAB SUPPORTING THE SOFFIT

MIN.
90° BEND

1m
SPECIFICATIONS MORTAR SHOULD BE NOT LESS THAN 2.1m , THE MINIMUM SHAFT SIZE SHOULD BE 900mm. MIN. FRAME DEPTH 150 mm) MIN OPE.
675

600x600 mm . 225mm GRADE C

15. ALL MANHOLES TO BE WATERTIGHT TO THE SATISFACTION OF THE EMPLOYERS
20 N/mm² CONCRETE BLOCKS TO 25 / 30 CONCRETE CONNECTION POSSIBLE FUTURE
675 mm MAX. TO FIRST STEP REPRESENTATIVE. COVER TO BE SET AS
COMPLY WITH IS EN 771-3 . SURROUND TO EXISTING SEWER CONNECTION EXISTING PUBLIC SEWER
225

TYPE NO. 1
225

PER MANUFACTURER'S
SPECIFICATION 600 1 NO. COURSE MIN.
1 : 3 SAND : CEMENT MORTAR WITH MANHOLE COVER AND FRAME SHALL 3 NO. COURSES MAX OF 150mm - 450mm DIA. ( INCL. ) DROP
675

MIN.
STEEL TROWEL FINISH AT A 1 : 30 675 mm MAX. TO GREATER THAN 1700mm
SLOPE TOWARDS THE CHANNEL
COMPLY TO IS EN 124 AND BS 7903 CLASS B ENGINEERING
500mm - 900mm DIA. ( INCL. ) DROP
PLAN OF SEPARATE CONNECTION
( ALL CLASS D400 COVERS SHALL HAVE FIRST STEP BRICKS SET IN C 50/60 MORTAR.
FLEXIBLE JOINT FLEXIBLE JOINT GREATER THAN 2300mm. TO COMBINED SEWER
300 C/C

MIN. FRAME DEPTH 150 mm MIN OPE.

600x600 mm . MANHOLE STEPS TO COMPLY WITH IS 25 x 25 mm CHAMFER
675 mm MAX. TO EN 13101, TYPE D, CLASS 1, GALVANISED 150 MIN. HEAVY DUTY COVER
FLOW FLOW
COVER TO BE SET AS PER FIRST STEP MILD STEEL & PLASTIC ENCAPSULATED,
STEPS ARE REQUIRED IN MANHOLES UP TO
AND FRAME D400
N CONNECTION OF SEPARATE F & SW
C/C
300

MANUFACTURER'S SPECIFICATION PRECAST CONCRETE 225 (TO SUIT150 mm OPE. ) .

A DEPTH OF 2.5 m . MANHOLE LADDERS ARE CONCRETE GRADE C
-
MANHOLE RINGS TO IS 420 IN
SYSTEMS TO COMBINED SEWER
225
50

1 NO. COURSE MIN. REQUIRED FOR MANHOLES WITH A DEPTH 30 / 37 IN ROOF ,

CONJUNCTION WITH IS EN 1917 : 2004 .
225

ROCKER PIPE ( 2 X DIAMETER 600 MIN. 600 MIN. 3 NO. COURSES MAX OF CLASS B WALLS AND BASE. -
IN EXCESS OF 2.5 m & ARE TO COMPLY WITH COVER TO BE SET AS PER
675

OR 1000 mm MAXIMUM ) ROCKER PIPE ( 2 X DIAMETER OR ENGINEERING BRICKS SET IN C 50/60 MINIMUM 2 LAYERS A393 MESH
IS EN 14396 & WITH MANUFACTURER'S SPECIFICATIONS
1000 mm MAXIMUM ) MORTAR REINFORCEMENT 1. ALL DIMENSIONS ARE IN MILLIMETERS (mm) UNLESS NOTED OTHERWISE.
150mm GRADE C 16 / 20 IN- SITU BS 4211. CLASS A.
REINFORCED CONCRETE ( 1lAYER EACH FACE
PRE-FORMED HALF CIRCLE 600 CONCRETE SURROUND . 1 : 3 CEMENT: SAND MORTAR WITH STEEL
BASE GRADE C 30 / 37 ELASTOMETRIC JOINT SEAL TO EN 681 WITH 50mm COVER) 2. AN INSPECTION CHAMBER SHOULD BE LOCATED AT OR WITHIN 1m OF THE
CHANNEL PIPES BOTTOM PRECAST SECTION TROWEL FINISH AT A 1 : 30 SLOPE PROPERTY BOUNDARY AT THE UPSTREAM END OF EACH SERVICE CONNECTION ON
75mm GRADE C 12/15 150 MIN. 150
TO BE BUILT INTO BASE TOWARDS THE CHANNEL THE PRIVATE SIDE OF THE CURTILAGE , IF PRACTICABLE .
BLINDING CONCRETE SECTION A - A STAINLESS STEEL CHAIN IN 150mm DIA. PVC PIPE
MANHOLE STEPS TO COMPLY WITH IS EN CONCRETE MINIMUM 75mm . INVERT SHOULD BE FORMED WITH
MANHOLE COVER AND FRAME SHALL '' DOWN '' POSITION SECURED
13101, TYPE D, CLASS 1, GALVANISED CAST-INSITU CONCRETE C 25 / 30 20mm 3. ANY PIPE AND ASSOCIATED ACCESS UPSTREAM OF THE POINT OF CONNECTION TO
COMPLY TO EN 124 AND BS 7903 REFER TO TABLE TO RESTRAINING HOOK , CHAIN
AGGREGATE FINISHED WITH A 1:3 150mm CONCRETE A PUBLIC SEWER IS A PRIVATE DRAIN AND SHOULD BE CONSTRUCTED IN
50

( ALL CLASS D400 COVERS SHALL HAVE MIN. MILD STEEL & PLASTIC ENCAPSULATED.
FOR PRECAST WHEN CHAMBER IS OCCUPIED ACCORDANCE WITH THE BUILDING REGULATIONS .
225

SURROUND
C/C
300

FRAME DEPTH 150 mm ) OPE. 600x600 mm . STEPS ARE REQUIRED IN MANHOLES UP CEMENT SAND MORTAR .
RING DIAMETER WHERE THE PIPE DIAMETER
TO A DEPTH OF 2.5 m . MANHOLE 4. ACCESS POINTS SHOULD BE LOCATED SO THAT THEY ARE ACCESSIBLE AND
COVER TO BE SET AS PER 1 NO. COURSE MIN.. 75 mm GRADE C 12 / 15 BLINDING IS 450 mm OR MORE.
LADDERS ARE REQUIRED FOR MANHOLES CONSTRUCTION JOINT. APPARENT TO THE MAINTAINER AT ALL TIMES FOR USE .THEY SHOULD AVOID REAR
MANUFACTURER'S 3 NO. COURSES MAX OF CLASS B CONCRETE SECTION A - A STOPPER
WITH A DEPTH IN EXCESS OF 2.5 m & ARE TEE JUNCTION GARDENS OR ENCLOSED LOCATIONS AND THEY SHOULD NEVER BE OVERLAIN WITH
SPECIFICATIONS ENGINEERING BRICKS SET IN C 50/60 TO COMPLY WITH IS EN 14396 & WITH DISTANCE BETWEEN TOP OF PIPE & 150 SURFACE DRESSING, TOPSOIL , ETC.
MORTAR BS 4211. CLASS A. UNDERSIDE OF PRECAST SECTION A
675

675 mm MAX. TO MANHOLE STEPS TO COMPLY WITH IS EN 5. COVERS AND FRAMES SHALL BE SUITABLE FOR ROAD AND TRAFFIC CONDITIONS
225

TO BE MIN. 50mm TO MAX. 300mm. 150mm GRADE C 25 / 30

FIRST STEP 13101,TYPE D, CLASS 1, GALVANISED MILD 1 : 3 CEMENT: SAND MORTAR WITH STEEL 225 'D' 225 600 SUBJECT TO APPROVAL FROM IRISH WATER .
FIRST RING SUNK INTO IN-SITU 600 CONCRETE SURROUND
STEEL & PLASTIC ENCAPSULATED. TROWEL FINISH AT A 1 : 30 SLOPE TOWARDS ROCKER PIPE 2 x Ø
CONCRETE BASE
225

ENGINEERING BRICK WORK MIN. MIN.

THE CHANNEL. OR 1000 mm MAX. 6. 200 mm ALL AROUND, 100 mm DEEP CONCRETE PLINTH WITH PROTECTIVE
LINING 1000 mm 20 N/mm² CONCRETE BLOCKS TO REINFORCED CONCRETE ROCKER PIPE 2 x Ø 90° BEND
MIN.
600

ABOVE BENCHING 150 MIN. BASE GRADE C 30 / 37 OR 1000 mm MAX. STAINLESS METAL BAND AROUND COVERS IN GREEN AREAS.
COMPLY WITH IS EN 771-3 . SELF CLEANING TOE HOLES TO BE 225mm GRADE C 25 / 30
THE ENGINEERING BRICK CAN BE IN PROVIDED WHERE CHANNEL EXCEEDS INVERT SHOULD BE FORMED WITH CONCRETE SURROUND 7. PROPRIETARY PREFABRICATED CHAMBER UNITS MAY ALSO BE USED,
'D'

SURFACE WATER MANHOLES 1 : 3 SAND : CEMENT MORTAR WITH STEEL 600mm WIDE . FLOW 600 FLOW
CAST-INSITU CONCRETE C 25 / 30 20mm
MAX.300

TROWEL FINISH AT A 1 : 30 SLOPE SUBJECT TO APPROVAL FROM THE ENGINEER.

MIN. 50

BUT THE MORTAR JOINTS ARE AGGREGATE FINISHED WITH A 1:3 MIN. TYPE NO. 2
TO BE FLUSH POINTED. TOWARDS THE CHANNEL STAINLESS STEEL CHAIN IN '' DOWN'' CEMENT SAND MORTAR .
325

POSITION SECURED TO RESTRAINING 150mm - 450mm DIA. ( INCL. ) DROP GREATER 8. CONCRETE CHAMBERS SHALL BE SURROUNDED BY A MINIMUM OF 150mm PL2 12.02.20 ISSUED FOR PLANNING MC RM
MC JC
HOOK , WHEN CHAMBER IS OCCUPIED THAN 900 AND LESS THAN 1700mm COMPACTED CLAUSE 808 MATERIAL.
BENCHING SLOPE TO RELIEVING ARCH FORMED BY 215X103X65 75 mm GRADE C 12 / 15 BLINDING PL1 13.12.19 ISSUED FOR PLANNING MC RM
500mm - 900mm DIA. ( INCL. ) DROP GREATER THAN MC JC
BE 1 : 10 TO 1 : 30 SOLID ENGINEERING BRICK CLASS A OR B WHERE THE PIPE DIAMETER IS 450 mm OR
SECTION A - A CONCRETE SEALED MANHOLE COVER TO
50

MORE. 1300mm AND LESS THAN 2300mm. COVER TO BE SET AS PER DRN P.E.
(RELIEVING ARCHES USED IN BRICK OR
225

ISSUE DATE DESCRIPTION

MANUFACTURER'S SUIT IS EN 124 LOADING ORIG P.D.
BLOCK WORK MANHOLES EXTEND OVER
FULL THICKNESS OF WALLS ) A SPECIFICATION. MINIMUM 600mm X 600mm
DRAWING STAGE
REINFORCED CONCRETE ROCKER PIPE
PLANNING
225

CLEAR OPENING
BASE GRADE C 30 / 37 REFER TO TABLE FOR
A ( 2 X DIAMETER OR PLAN
PC RING DIAMETER 1000 mm MAXIMUM )
75mm GRADE C 12/15 1 NO. COURSE MIN.
MIN.600x600 mm MINIMUM INTERNAL
BLINDING CONCRETE SECTION B - B FLEXIBLE JOINT SQUARE OPE
3 NO. COURSES MAX OF CLASS
DIMENSIONS 600mm DIAMETER Dublin Office:
FLEXIBLE JOINT B ENGINEERING BRICKS
ROCKER PIPE MINIMUM WIDTH OF OR 600 mm X 600 mm . Sandwith House, 52-54 Lower Sandwith Street, Dublin 2, Ireland.
( 2 X DIAMETER OR BENCHING FOR LANDING Tel: (01) 677 3200 Fax: (01) 677 3164
B 1000 mm MAXIMUM ) PIPES BUILT INTO CHAMBER 600 215 THICK 20 N/mm²
AREA TO BE 500 mm. London Office:
WALL OR JOINT FORMED WITH CONCRETE BLOCKWORK IN
1200 MIN. 12 Mill Street, London SE1 2AY, United Kingdom
FLOW . FLOW WATERTIGHT SEALS ACCORDANCE WITH IS EN 771-3 BARRETT M A H O N Y
215 SEE NOTE 10. 215 Tel: (0044) 084 5413 2722
MINIMUM WIDTH OF FLOW FLOW
REFER TO DETAIL A Consulting Engineers, Civil . Structural . Project Management.E-mail: [email protected] Web: www.bmce.ie
215

BENCHING FOR LANDING

MANHOLE COVER
325

AREA TO BE 500 mm. 600 Y - JUNCTION FOR BACKFILL AND BEDDING

Min

600 CHAIN 600 mm R

AND MIN OPE. 225mm PRECAST

600 x 600mm. MIN. MIN. DETAILS
SECTION BASE OR 225mm IN- SITU
Institution
600 Structural

215
50mm CROSS FALL 215 600 215 CONCRETE C 25 / 30
MIN. PIPE JOINT WITH CHANNEL TO BE
FLEXIBLE JOINT FLEXIBLE JOINT
150 mm GRADE C
16 / 20 IN -SITU LOCATED MINIMUM 100mm INSIDE FACE
QAS INTERNATIONAL
ISO 9001:2008
REGISTERED COMPANY
Engineers International Federation of
A STOPPER Certificate No. IRE1213
Consulting Engineers
CONCRETE SURROUND OF MANHOLE BENCHING
ROOF PLAN 150mm GRADE C 25 / 30
1200

PLAN CONCRETE SURROUND CLIENT

600
FLOW FLOW
GREENLEAF HOMES LTD.
A A MINIMUM MANHOLE DIMENSIONS '' D '' 45 BEND 215 THICK 20 N/mm
FLOW FLOW
600 MIN.
225mm GRADE C 25 / 30 CONCRETE BLOCK WORK IN
DIAMETER OF LARGEST PIPE IN INTERNAL DIMENSION OF
ROCKER PIPE MINIMUM MANHOLE DIAMETERS CONCRETE SURROUND ACCORDANCE WITH IS EN 771-3 PROJECT TITLE BM PROJECT No.

215
MANHOLE ( mm ) MANHOLE ( mm )
ROCKER PIPE ( 2 X DIAMETER OR FLOOR PLAN MIXED-USE DEVELOPMENT, THE FORMER
215

( 2 X DIAMETER OR
1000 mm MAXIMUM ) B
1000 mm MAXIMUM ) DIAMETER OF LARGEST PIPE IN
MANHOLE ( mm )
INTERNAL DIAMETER OF
MANHOLE ( mm )
TYPE NO. 3
NOTES
GALLAHER SITE, AIRTON ROAD, TALLAGHT, 19.136
LESS THAN 375 1200 150mm - 450mm DIA. ( INCL. ) DROP GREATER THAN D24
PLAN INVERT SHOULD BE FORMED WITH LESS THAN 375 1200 600mm AND LESS THAN 900mm 1. ACCESS JUNCTIONS (AJ) TO BE USED FOR INVERT DEPTHS UP TO 0.6m MODEL REFERENCE MODEL REV. SUITABILITY
CAST-INSITU CONCRETE C 25 / 30 1350 500mm - 900mm DIA. ( INCL. ) DROP GREATER THAN 2. INSPECTION CHAMBERS TO BE USED FOR INVERT DEPTH 0.6m TO 1.0m INSPECTION
375 TO 450
20mm AGGREGATE FINISHED WITH A 1:3 375 TO 450 1350 600mm AND LESS THAN 1300mm. CHAMBERS CAN BE CONSTRUCTED IN BLOCKWORK (AS DETAIL 'N') OR BE
CEMENT SAND MORTAR . PROPRIETARY TYPE PRECAST OR uPVC SUBJECT TO ENGINEERS APPROVAL DRAWING TITLE
500 TO 750 1500 3. FOR INVERT DEPTH'S IN EXCESS OF 1.0m DEEP USE MAHOLE TYPE CONSTRUCTION
500 TO 750 1500 STANDARD DRAINAGE DETAILS
F BLOCKWORK MANHOLE <
-
(450mm DIAMETER & DEPTH G PRE- CAST CONCRETE MANHOLE H IN- SITU CONCRETE MANHOLE L BACKDROP MANHOLE M INSPECTION CHAMBER
-
TO INVERT < 2m) - -
-
(BLOCKWORK CONSTRUCTION) DRAWING No.

ARD-BMD-00-XX-DR-C-1200
ISSUE

PL2