FD34x Fiber-Optic Intrusion Detection System
Proven Reliability in Remote Perimeter Security
Fiber SenSys’ FD34X series Fiber Optic Intrusion Detection
System offers high performance intrusion detection
with modern features and communication options.
Designed for remote deployment with no power or communications needed in the
field, the indoor and outdoor rated Fiber Defender™ Model FD341/FD342 Alarm
Processing Unit (APU) utilizes insensitive fiber-optic cable in addition to sensing fiber. The use of insensitive lead-in
cable allows the APU to be located up to 20 kilometers away from the protected zone. Movement or vibration in
the physical environment causes the sensing fiber to report back to the APU that there is a disturbance.
Single or dual-channel
APU (FD341 FD342) The FD34x provides both single channel (FD341) or independent dual-
channel (FD342) operation, and users can connect sensor cable from two
One or two detection separate deployment locations. Dual-channel capability reduces the FD342
zones, up to 5 kilo- overall system cost and power consumption. Independent zone control
meters in length allows for maximum versatility, such as a wall and a fence protection zone
combination. The FD34x also provides intrusion detection system control
Optional IP/XML with communication options that include IP/XML capability.
communications
DSP signal processing
for accurate detection Real-time anemometer
for wind compensation
The FD34x series Digital Signal Processor (DSP) and electronics provides
users an intrusion detection system that is immune to the effects of EMI, Sensor cable immune to
lightning, magnetic fields and radio frequency transmissions. Enhanced DSP EMI, RFI, lightning
capabilities filter out sensor cable signals from non-threat events such as
Completely inert and
wind, weather and small animals. Made in the U.S.A., the FD34x guarantees intrinsically safe sensor
system performance and high reliability for perimeter security.
Simple, flexible
deployment
2925 NW Aloclek Drive, #120
Hillsboro, Oregon 97124, USA
Tel: +1(503)692-4430 • Toll free (US) +1(888)736-7971
www.fibersensys.com
Fiber SenSys and Fiber SenSys logos are trademarks of Fiber SenSys, Incorporated BR-SM-008 Rev. D 140731
The Model FD342 is uniquely suited to monitor and protect two zones from a single
alarm processing unit. Dual zone protection can include both a fence and/or wall
zone. Each of the FD342’s channels is calibrated independently to set optimal
detection sensitivity levels. Each channel provides zone coverage up to five
kilometers with individual settings to ensure that the FD342 screens out sensor
signals from non-threatening events, like wind, while focusing on genuine intrusion
events. The use of insensitive lead-in cable allows the APU to be located up to 20
kilometers away from the protected zone.
FD34X Technical Specifications
Parameter Specification
Application Perimeter fence or wall application
Sensor Passive, optical fiber; resistant to EMI, RFI and corrosion
Installation Sensing fiber in conduit; conduit attached to fence with stainless steel wire ties
Number of zones per APU FD341 (Single-channel – 1 zone) or FD342 (Dual-channel – 2 zones)
Maximum sensing cable per zone 5 Kilometers (3.1 miles/16,400 ft.)
Maximum insensitive lead-in cable per 20 Kilometers (12.43 miles / 65,616.7 ft.)
zone
APU electrical power Input voltage: 12-24 volts / Power: 3 Watts @ 12 to 24 VDC
Communications RS-232 serial communications, IP/XML communications
APU Memory Stores data from up to 24 alarms
Tuning parameters Sensitivity (for cuts and climbing)
Number of events before alarming (for cuts and climbing)
Wind rejection
Tamper (enable/disable)
For more information, contact us at
[email protected]Tel: +1(503)692-4430
High Performance - High Reliability - High Security
Toll free (US) +1(888)736-7971
Fiber SenSys and Fiber SenSys logos are trademarks of Fiber SenSys, Incorporated BR-SM-008 Rev. D 140731
