User Manual

1. The product is a Tuya Bluetooth lock, the administrator of the APP is the ultimate administrator
of the lock, and the operation function of the lock end is an auxiliary operation, please be sure to
download the Smart Life APP to bind the administrator, unless it can be ensured that the lock
will not be used by unrelated people APP is bundled.
2. The square bar of the product needs to be
positioned to unlock normally. Please be sure to insert the square bar into the front handle to the
end, and then position the square rod correctly according to the instruction manual.
3. Before it is installed on the door, be sure to insert the square rod into the bottom of
the front handle and position it correctly before trying to twist the key to unlock it.
After the product is installed on the door, make sure the square rod is positioned
correctly before twisting key. WARNING: Blindly twisting the key can cause
mechanical failure of the product.
4.The front handle connecting wire terminal needs to be inserted into the female seat
of the rear handle setting plate according to the marking (red to red), otherwise it
will cause a short circuit.
 Parameters
Cover: D70mm / Lever: L150mm / Height:62mm Power Supply:
4 x AAA Alkaline Batterys

Material: Emergency Supply:

Aluminum alloy+Acrylic USB(Type-C Interface)

Available Thickness: Working Voltage: 6V

35mm ~ 55mm Alarm Voltage :4.8V

Unlock Way: Capacity:

Key/Fingerprint/password/Tuya APP Fingerprint——50sets
Password——100sets

Parts list

Key x 2 Exterior Assembly x 1

Interior Assembly x 1 Battery Cover x 1

Spring x 1 Screw Bolt x 2 Screw x 2 Hollow Square Bar x 1

12

11 7 6

8
9

5 4
10
1
3
13 2

14
15

1.Front Handle 6.Key 11.Screw

2.Emergency power supply 7.Data Line 12.Battery Cover

3.Front Cover 8.Spring 13.Battery Box

It is not necessary when the door's
thickness does not exceed 45mm

4.Hollow Square Bar 9.Back Cover 14.Data Line Interface

5.Screw Bolt 10.Back Handle 15.Setting Button

 Installation
1. The square bar of the product needs to be positioned to unlock normally. Please
be sure to insert the square bar into the front handle to the end, and then position
the square rod correctly according to the instruction manual.

2. Before it is installed on the door, be sure to insert the square rod into the bottom of
the front handle and position it correctly before trying to twist the key to unlock it.
After the product is installed on the door, make sure the square rod is positioned
correctly before twisting key. WARNING: Blindly twisting the key can cause
mechanical failure of the product.

3.The front handle connecting wire terminal needs to be inserted into the female seat
of the rear handle setting plate according to the marking (red to red), otherwise it
will cause a short circuit.

01. Drill holes on the door and install the 02. Install the two screw bolts on the front
lock body according to the drawings cover ,Insert the hollow square bar into the
bottom of the front lever and let the data
line stick out

03. ①Rotate the bar to the bottom towards the handle direction.
②Then rotate back 90° to complete the positioning
 Installation
Install the spring to prevent the square bar
from detaching from the front handle
and causing malfunction.

04. Insert the exterior assembly into the 05. Install the interior assembly on the door.
door hole Make sure the connection wire goes through
the spring and the back handle.

RED TO RED

06. A-Tighten the door lock with two screws and connect the data cable.
B-Be sure to follow the markings (red to red) to connect the cable terminal to the female socket of
the setting board, otherwise it will cause a short circuit in the product.

07. Install 4 AAA alkaline batteries and the 08. As shown in the picture, press down to
battery cover to complete the installation open the battery cover
 Lock function setting
1. Function and operation
1) Administrator information: refers to the ingerprint and password of the administrator.
2) Unlock information: refers to the entered ingerprints and passwords (including administrators and ordinary
users)
3) The "#" key has two modes:
A. It is the con irmation key or the function key for entering the menu;
B. The clear key/back key (click to clear when entering the password).
4) The operating system will automatically exit if there is no operation for more than 20 seconds.
5) After the voltage is lower than 4.8V, it will prompt "low battery, please replace the battery" every time you
unlock, please replace the battery in time.
6) In Always unlock mode, click the setting button, and the voice broadcasts "Always unlock mode,please lock soon."
Click the setting button again and the voice broadcasts "Always unlock mode cancel".
2. Reset factory default state
1) The factory administrator's initial password is "123456". In the initial state, any ingerprint can unlock the lock.
2) Press and hold the setting button until you hear the fourth "beep" and the red light of the ingerprint head lights up.
Release the setting button within 3 seconds when the red light lights up(timeout to
exit the operation), and the original settings are restored successfully.
3. Door lock function management
After the operation is successful,
Factory default state the voice broadcast:
To add administrator,press 1
To add user,press 2
To delete user,press 3
“Please verify To switch voice mode,press 4
administrator” To switch language,press 5
Press “1" + “#” Enter “123456#” To restore factory settings 6

4.Menu list

Password enroll 6-10 digits 2 times “Enroll success”

Or Continue to add
1 Add administrator Or
Fingerprint enroll 5 times
Press “#” to return

Password enroll 6-10 digits 2 times “Enroll success”

2 Add user Or Continue to add
Fingerprint enroll 5 times Or
Press “#” to return

“Delete success”
Enter unwanted ID
Continue to delete
3 Delete user or passwords
Or
or ingerprints
Press “#” to return

“Silent mode”
4 Switch voice mode Or
“Silent mode Cancel”

5 Switch language Chinese / English

6 Restore factory settings Press "#" con irm

 APP settings

Reminder: The product is a Tuya Bluetooth lock, the administrator of the APP is the ultimate administrator of the lock, and the
operation function of the lock end is an auxiliary operation, please be sure to download the Smart Life APP to bind the
administrator, unless it can be ensured that the lock will not be used by unrelated people APP is bundled.

1. Download and install the "Smart Life" APP from the application market.
Remarks: Users can also download the "Tuya Smart" APP, and the setting and usage methods are the same.

2. After the installation is complete, follow the prompts to register and log in.
Users can also download and install the APP by scanning the QR code below:

1. Register an account and add devices

Register an account with a mobile a. Click to add this device.

phone number b. After the addition is successful,
the voice prompts "connected".
2. Improve family information

Quickly select and complete family information

3. Fingerprint and password enroll

a. Enter the ingerprint, password and card information registration in the family.
b. To register a ingerprint, you need to press 6 times, and you can add a name note after entering the ingerprint.
3. Fingerprint and password enroll 4. Delete ingerprints and passwords

c. The password can be randomly generated or ixed, and the

password needs to be copied or remembered.

5.One-time password
6. Log 7. More

1. Automatic locking: Normally open mode switch;

2. Door lock volume: Mute setting, lock end entering menu will broadcast voice;
3. Door lock language: Switch between Chinese and English.

8. Unbind

1. Unbind: The unlocking record is still retained;

2. Release and clear data: Restore factory settings, clear all information.