QUARTERLY EXAMINATION IN TLE 8 (Carpentry)

Directions: Choose the letter of the best answer. Write the chosen letter in your activity notebook.
1. Which tool/material is used for roofing?
a. plywood b. gravel c. corrugated Galvanized Iron Sheet d. nails
2. Which is added in the mixture of cement and aggregate?
a. sand b. water c. shovel d. gravel
3. Which of the following is made of metal used for fastening woods?
a. plywood b. twister c. nails d. sand
4. Which is used to cut tie wires?
a. plumb Bob b. ruler c. combination pliers d. twister
5. Which is a fine-toothed saw used to cut metal and pipes?
a. Cross-cut-saw b. Hacksaw c. Ripsaw d. Try square
6. Which is used to cut wood along the grain?
a. circular saw b. rip saw c. claw hammer d. cross-cut-saw
7. Which is used for measuring long distances?
a. level bar b. push-pull-rule c. plumb-bob d. try square
8. Which is used to test the squareness of a stock?
a. try square b. level c. pull-push-rule bar d. claw hammer
9. Which is a coarse aggregate?
a. sand b. gravel c. cement d. nails
10. Which is a fine gritty, substance found in the shore and desert?
a. gravel b. sand c. water d. cement
11. Which of the following is a powdered substance which when mixed with water acts as a binder of aggregate?
a. cement b. nails c. sand d. water
12. Which is used to check vertical alignment?
a. try square b. level c. plumb bob d. twister
13. Which of the following tools is used to check vertical and horizontal positions?
a. level bar b. shovel c. ripsaw d. claw hammer
14. Which is used for mixing aggregate, cement, and water?
a. shovel b. cement c. hacksaw d. nails
15. Which is used for cutting wood across the grain?
a. push-pull-rule b. combination pliers c. twister d. cross-cut-saw
16. Which entries of the requisition form should be written next to the suggested project?
a. balance on hand b. date of requisition c. materials and description d. unit price
17. How many steps are required in the accomplishment of the requisition form?
a. 2 b. 4 c. 6 d. 7
18. Which is the sixth step in accomplishing the requisition form?
a. Write your name as a requisitioner. c. List the unit of materials to be requisitioned
b. Write the number of required materials. d. State the name of the project & date you requested for materials.
19. What is the next step after listing the unit of materials to be requisitioned?
a. List the cost per unit and the total cost. c. Enumerate the materials with their description
b. List the unit of materials to be requisitioned. d. Fill in the classification of the project and its purpose.
20. Which is the 7th step in accomplishing the requisition form?
a. Write your name as requisitioner. c. Secure the approval of the supply officer
b. Write the number of required materials d. List the unit of materials to be requisitioned.
21. Vinz wants to have 5 liters of paint in his suggested project. In what part of the requisition form is liters written?
a. Balance on hand b. Materials and description c. Requisition unit d. Total
22. Which is the second step to consider in accomplishing the requisition form?
a. Write the number of required materials. c. Write your name as requisitioner
b. List the cost per unit and the total cost d. Enumerate the materials with their description
23. Which is the fourth step involved in requesting materials and tools?
a. Write your name as requisitioner. c. Write the number of required materials
b. List the cost per unit and the total cost d. Enumerate the materials with their description.

24. Which is used for sharpening edge-cutting tools such as chisel?

a. saw set b. oil stone c. nail set d. files
25. Which is one of the procedures in segregating and labeling non-functional tools and equipment?
 a. Conduct an inventory of tools and equipment c. Wait until the others are doing
b. Asking co-worker d. Junk defective tools
26. Which is used for transferring measurement?
a. plumb bob b. divider c. pencil d. caliper
27. Which is used to layout or mark cutting lines?
a. chalk line b. pencil c. marking gauge d. steel square
28. Which is used to scribe arcs and circle in the metal or wood?
a. compass b. divider c. marking gauge d. steel square
29. Which is used in measuring and testing the squareness of a wood?
a. cabinet scraper b. spirit level c. try square d. steel square
30. Which is an example of functional portable power tool used for sanding furniture?
a. Sander with ground wires c. Sander with damage plug
b. Sander with cut ground wires d. Sander with cracked switch
31. Which is used to drive and pull out nails on a wooden surface?
a. claw hammer b. screwdriver c. cabinet scraper d. mallet
32. Which is used to protect the eyes against flying debris and harmful liquids?
a. apron b. face mask c. goggles d. ear protector
33. Which is called a complete tool?
a. tools with insulated handle c. screwdriver with broken handle
b. hammer with cracked handle d. electric without ground wires
34. Which is used to protect the hands while working?
a. claw hammer b. gloves c. screwdriver d. face mask
35. Which of these is a defective tool?
a. tool that has crack in its handle c. saw with handle
b. Tool with sharp blade d. chisel with sharp edge
36. Which is used to apply paint or varnish on wood surfaces?
a. claw Hammer b. screwdriver c. paint brush d. nail set
37. Which is used for holding together pieces of lumber while working?
a. Apron b. Face Mask c. Goggles d. c-clamp
38. Which does not belong to the group?
a. Tools that have broken guards. c. On and off switches are not in good conditions
b. Tools that have no ground wires, or cords of standard tools d. Tool blades that are sharp and fixed
39. Which type of maintenance is not directly included in the total maintenance costs, but might be a component
of total overall cost?
a. preventive b. breakdown c. predictive d. prescriptive
40. Preventive maintenance is used to ensure that breakdowns ____________________.
a. are eliminated b. are reduced c. are less costly d. will not happen
41. With regard to maintenance, breakdown maintenance is ______while predictive maintenance is __________
a. proactive, cheaper b. cheaper, reactive c. reactive, proactive d. cheaper, more productive
42. Generally, cleaning, lubricating, and storing properly are basic __________________ in tools and equipment.
a. breakdown maintenance c. predictive maintenance
b. preventive maintenance d. run-based maintenance
43. Which of these is best used to remove hex screw?
a. witch’s curse b. wrench c. power drill d. Hex key wrench
44. Teflon tape is used in____________.
a. plumbing repairs b. tough holds c. electrical repairs d. vehicle repairs
45. Repair and maintenance of tools is important because_________.
a. it makes work faster b. it ensures safety c. it improves work d. it reduces time