Master Specifications

200/225/250/275 Verado Master Specifications

General Specifications
Model Specifications
149 kw (200 HP)
168 kw (225 HP)
Kilowatts (Horsepower)
186 kw (250 HP)
205 kw (275 HP)
Weight
50.8 cm (20 in.) 293 kg (645 lbs.)
63.5 cm (25 in.) 299 kg (659 lbs.)
76.2 cm (30 in.) 307 kg (677 lbs.)
Displacement (All Hp) 2.6L (158.5 cu. in.)
RPM
Idle 550 ± 50 RPM
WOT 5800 - 6400 RPM
SmartCraft DTS® electronic throttle, intercooled supercharged aspiration with
Induction System
electronic boost pressure control
Fuel System Computer controlled sequential multi-port Electronic Fuel Injection
Ignition System SmartCraft Propulsion Control Module (PCM) 03 digital inductive
Charging System Regulated belt driven 70 amp alternator
Exhaust System Through prop
Cooling System Water cooled - thermostat with pressure control
Lubrication System
Integrated dry sump 7 Liters (7.4 qts.)
Engine Control System SmartCraft PCM 03 Digital Throttle and Shift (DTS)
Trim System SmartCraft programmable
Maximum Tilt Range 73° (-6° to 67°)
Maximum Trim Range 20° (-6° to 14°)
Steering System Electric - Hydraulic Power Steering with integral hydraulic cylinder

Fuel System Specifications

Fuel System Specifications
Type of fuel
Automotive unleaded with a minimum pump posted
149 kw (200 hp), 168 kw (225 hp), 186 kw (250 hp)
octane rating of 87 (90 RON)
Automotive unleaded with a minimum pump posted
205 kw (275 hp)
octane rating of 91 (96 RON)
Approximate fuel pressure @ idle 279 - 289 kPa (40 - 42 psi)
Fuel filtration
Fuel inlet water separator 2 Microns
High pressure 20 Microns

Page 1A-2 90-896580100 JULY 2004

 Master Specifications

Ignition Specifications
Ignition Specifications
Full Throttle RPM (All Models) 5800 - 6400
Idle RPM (All Models) 550
Ignition Type Digital Inductive
Spark Plug Type NGK ILFR6G
Spark Plug Gap 0.8 mm (0.031 in.)
Spark Plug Hex Size 16 mm
Spark Plug Torque 27.5 Nm (19 lb. ft.)
Spark Plug Hole Size 14 mm
Firing Order 1-3-5-6-4-2
Ignition Timing @ Idle Not Adjustable; Controlled by PCM
Ignition Timing @ WOT Not Adjustable; Controlled by PCM
PCM Over Speed Limiter Activates @ 6500 RPM

Charging and Starting Specifications

Charging and Starting Specifications
Alternator Output (Regulated)
Output @ Battery (@ 1000 RPM) 37 - 44 Amperes
Output @ Battery (@ 3000 RPM) 53 - 69 Amperes
Output @ Alternator (@ 1000 RPM) 48 - 54 Amperes
Output @ Alternator (@ 3000 RPM) 65 - 72 Amperes
Voltage Set Point 14.5 +/- 0.25 Volts
Regulator Current Draw1.
Ignition Switch "OFF" (maximum) 1.0 mA
Ignition Switch "ON" 350 mA
Starter Draw (Under Load) 160 Amperes
Starter Draw (No Load) 60 Amperes
Minimum Brush Length 65.4 mm (0.25 in.)
Battery Rating
Marine Cranking Amperes (minimum) 1000
Cold Cranking Amperes (minimum) 800
Ampere Hour (Ah) (minimum) 180

1. All model alternator specifications require an amperage draw of less than 1.0 mA with the ignition key in the "OFF" position and an
amperage draw of not more than 350.0 mA with key in the "ON" position.

90-896580100 JULY 2004 Page 1A-3

Master Specifications

Cylinder Head Specifications

Cylinder Head Specifications
Maximum deck warp 0.075 mm (0.003)
Number of valves 24
Number of valves per cylinder 4
Number of cams 2
Cam bearing journal (intake and exhaust) 28.95 mm (1.1398 in.)
Camshaft bearing cap ID 29.000 - 29.021 mm (1.1417 - 1.1425 in. )
Cam lobe
Intake 42.50 mm (1.6732 in.)
Exhaust 43.55 mm 1.7145 in.)
Valve lash
Intake 0.150 - 0.230 mm (0.0059 - 0.009)
Exhaust 0.350 - 0.430 mm (0.0137 - 0.0169 in.)
Valve seat angles 30°, 45°, 60°
Valve spring free length 48.77 mm (1.920 in.)
Valve outside diameter
Intake 32.0 ± 0.15 mm (1.259 ± 0.0059 in.)
Exhaust 27.2 mm ± 0.190 (1.0708 ± 0.0059 in.)
Valve face width (intake and exhaust) 2.25 mm (0.0886 in.)
Valve margin
Intake 0.75 mm (0.0295 in.)
Exhaust 0.65 mm (0.0256 in.)
Valve guide bore ID (intake and exhaust) 6.00 - 6.016mm (0.2362 - 0.2368 in.)
Valve stem diameter
Intake 5.97 mm (0.235 in.)
Exhaust 5.96 mm (0.2346 in.)
Valve stem run-out (maximum) 0.038 mm (0.0015 in.)
Valve stem to valve guide clearance
Intake 0.03 - 0.046 mm (0.0011 - 0.0018 in.)
Exhaust 0.04 - 0.056 mm (0.0015 - 0.0022 in.)
Valve seat contact width (intake and exhaust) 2.25 mm (0.0886 in.)

Page 1A-4 90-896580100 JULY 2004

 Master Specifications

Cylinder Block/Crankcase Specifications

Cylinder Block/Crankcase Specifications
Number of cylinders 6
Displacement 2.6 Liters (158.6 CID)
Compression ratio 8.25:1
Standard bore 82.00 mm (3.228 in.)
Stroke 82.0 mm (3.228 in.)
Cylinder bore maximum taper (service) 0.0762 mm (0.003 in.)
Cylinder bore maximum out of round (service) 0.0762 mm (0.003 in.)
Cylinder block main bearing 65.997 - 66.013 mm (2.5982 - 2.5989 in.)
Crankshaft main bearing journal 59.985 - 60.001 mm (2.3616 - 2.3622 in.)
Crankshaft pin journal 49.982 - 50.0 mm (1.9678 - 1.968 in.)
Crankshaft end play 0.08 - 0.19 mm mm (0.003 - 0.007 in.)
Crankshaft run out 0.05 mm (0.002 in.)
Crankshaft main bearing oil clearance (without expansion) 0.014 - 0.042 mm (0.0005 - 0.0016 in.)
Crankshaft pin bearing oil clearance (without expansion) 0.020 - 0.050 mm (0.0008 - 0.0019 in.)
Connecting rod wrist pin bore diameter 22.005 - 22.014 mm (0.8663 - 0.8666 in.)
Connecting rod crankshaft pin diameter 53.000 - 53.018 mm (2.0866 - 2.0873 in.)
Piston skirt standard diameter 81.975 mm (3.2273 in.)
Piston wrist pin bore diameter 22.004 - 22.011 mm (0.8662 - 0.8665 in.)
Wrist pin diameter 21.997 - 22.000 mm (0.8660 - 0.8661 in.)
Top ring grove width 1.25 mm (0.049 in.)
Second ring grove width 1.25 mm (0.049 in.)
Third ring grove width 2.05 mm (0.081 in.)
Top ring thickness 1.19 mm (0.047 in.)
Second ring thickness 1.19 mm (0.047 in.)
Third ring thickness 1.98 mm (0.078 in.)
Top ring side clearance 0.04 - 0.08 mm (0.001 - 0.003 in.)
Second ring side clearance 0.04 - 0.08 mm (0.001 - 0.003 in.)
Third ring side clearance 0.05 - 0.17 mm (0.002 - 0.006
Top ring end gap 0.27 - 0.42 mm (0.010 - 0.016 in.)
Second ring end gap 0.42 - 0.62 mm (0.016 - 0.024 in.)
Oil ring end gap 0.2 - 0.7 mm (0.007 - 0.027 in.)

Power Trim Specifications

Power Trim Specifications
Trim up circuit pressure, maximum 18,270 - 28,960 kPa (2650 - 4200 psi)
Trim down circuit pressure 1255 - 2765 kPa (182 - 401 psi)
Power Trim and Steering Fluid or Automatic Transmission Fluid (ATF)
System fluid
(Type Dexron III)

90-896580100 JULY 2004 Page 1A-5

Master Specifications

Oil System Specifications

Oil System Specifications
Engine Capacity Wet 7 liters (7.4 qts.)
Engine Capacity Dry 8 liters (8.4 qts.)
Oil Filter Part Number 35-883701K01
Oil Pressure (Minimum) @ 550 RPM 70 kPa (10 psi)
Oil Pressure (Minimum) @ 6000 RPM 220 kPa (32 psi)
IOM thermostat opening temperature 105 °C (221 °F)

Gear Housing Specifications (Standard Rotation)

Gear Housing Specifications (Standard Rotation)
Gear Ratio 1.85:1 (13/24 Teeth)
Gearcase Capacity 970 ml (32.8 fl.oz.)
Gear Lubricant Type Premium Gear Lubricant
Pinion Height 0.635 mm (0.025 in.)
Forward Gear Backlash 0.482 - 0.660 mm (0.019 - 0.026 in.)
Reverse Gear Backlash 1.27 - 1.47 mm (0.050 - 0.058 in.)
Water Pressure @ RPM 55 - 68.9 kPa (8 - 10 psi)
Gear Housing Pressure (without gear lubricant, 5 minutes without
103.4 kPa (15 psi)
leakage)

Gear Housing Specifications (Counter Rotation)

Gear Housing Specifications (Counter Rotation)
Gear Ratio 1.85:1 (13/24 Teeth)
Gearcase Capacity 970 ml (32.8 fl.oz.)
Gear Lubricant Type Premium Gear Lubricant
Pinion Height 0.635 mm (0.025 in.)
Forward Gear Backlash 0.482 - 0.660 mm (0.019 - 0.026 in.)
Reverse Gear Backlash 1.27 - 1.47 mm (0.050 - 0.058 in.)
Water Pressure @ RPM 55 - 68.9 kPa (8 - 10 psi)
Gear Housing Pressure (without gear lubricant, 5 minutes without
103.4 kPa (15 psi)
leakage)

Power Steering Specifications

Power Steering Specifications
Fluid Type SAE 0W-30 synthetic power steering fluid
Capacity Typical 1 - 2 liters (1 - 2 quarts)
Current Draw Shall not exceed 75 Amps
Steering Ratio (40 cc helm and single steering cylinder, lock to
4.1 turns
lock)
Steering Ratio (50 cc helm with dual steering cylinders, lock to
6.5 turns
lock)

Page 1A-6 90-896580100 JULY 2004