JOB NO. ITEM NO.

Brown & Root, Inc. PURCHASE ORDER NO.

SPECIFICATION NO.
CENTRIFUGAL COMPRESSOR REVISION NO. DATE `
DATA SHEET (API 617-6TH) PAGE 1 OF 6 BY
SI UNITS
1 APPLICABLE TO: PROPOSAL PURCHASE AS BUILT

2 FOR UNIT

3 SITE SERIAL NO.

4 SERVICE NO. REQUIRED

5 CONTINUOUS INTERMITTENT STAND BY DRIVER TYPE (3.1.1)

6 MANUFACTURER MODEL DRIVER ITEM NO.

7 NOTE: INFORMATION TO BE COMPLETED: BY PURCHASER BY MANUFACTURER

8 OPERATING CONDITIONS

9 OTHER CONDITIONS (3.1.2)

10 (ALL DATA ON PER UNIT BASIS) NORMAL A B C D E

11

12

13 GAS HANDLED (ALSO SEE PAGE )

14 m³/h (1.013 BAR & 0 °C DRY)

15 WEIGHT FLOW, kg/h (WET) (DRY)

16 INLET CONDITIONS

17 PRESSURE (BAR) (kPa abs)

18 TEMPERATURE (°C)

19 RELATIVE HUMIDITY %

20 MOLECULAR WEIGHT (%)

21 Cp/Cv ( K1) OR (KAVG)

22 COMPRESSIBILITY (Z1) OR (ZAVG)

23 INLET VOLUME, (m³/h) (WET / DRY)

24 DISCHARGE CONDITIONS

25 PRESSURE (BAR) (kPa abs)

26 TEMPERATURE (°C)

27 Cp/Cv (K2) OR (KAVG) NOTE 1

28 COMPRESSIBILITY (Z1) OR (ZAVG) NOTE 1

29

30 kW REQUIRED (ALL LOSSES INCLUDED)

31 SPEED (RPM)

32 ESTIMATED SURGE, m³/h (AT SPEED ABOVE)

33 POLYTROPIC HEAD (N-m/kg)

34 POLYTROPIC EFFICIENCY (%)

35 CERTIFIED POINT

36 PERFORMANCE CURVE NUMBER

37 PROCESS CONTROL

38 METHOD SUCTION THROTTLING VARIABLE INLET SPEED VARIATION DISCHARGE COOLED BYPASS

39 FROM (BAR)(kPa abs) GUIDE VANES FROM % BLOWOFF FROM

40 TO (BAR)(kPa abs) (3.4.2.4) TO % TO TO

41

42 SIGNAL SOURCE ( 3.4.2.1)

43 TYPE ELECTRONIC PNEUMATIC OTHER

44 RANGE MA (BAR)(kPa abs)

45

46 ANTI-SURGE BYPASS MANUAL AUTOMATIC NONE

47

48 REMARKS:

49

50 NOTE 1: IF GAS ANALYSIS IS GIVEN, MANUFACTURER SHALL SUPPLY DATA, OTHERWISE DATA SHALL BE SUPPLIED BY USER.

07/96 EF-050-90.09-M SHT 1 OF 6 API617SI.XLS REV 0

 Brown & Root, Inc.
JOB NO. 0 ITEM NO.
CENTRIFUGAL COMPRESSOR REVISION NO. 0 DATE ###
DATA SHEET (API 617-6TH) PAGE 2 OF 6 BY 0
SI UNITS
1 OPERATING CONDITIONS (Continued) (3.1.2) (3.1.3)

2 GAS ANALYSIS: OTHER CONDITIONS (2.11.1.3)

3 MOL % NORMAL A B C D E REMARKS: (2.11.1.8)

4 MW

5 AIR 28.966

6 OXYGEN 32.000

7 NITROGEN 28.016

8 WATER VAPOR 18.016

9 CARBON MONOXIDE 28.010

10 CARBON DIOXIDE 44.010

11 HYDROGEN SULFIDE 34.076 (2.11.1.7)

12 HYDROGEN 2.016

13 METHANE 16.042

14 ETHYLENE 28.052

15 ETHANE 30.068

16 PROPYLENE 42.078

17 PROPANE 44.094

18 I-BUTANE 58.120

19 n-BUTANE 58.120

20 I-PENTANE 72.146

21 n-PENTANE 72.146

22 HEXANE PLUS

23

24

25 TOTAL

26 AVG. MOL. WT.

27 LOCATION: (2.1.9) NOISE SPECIFICATIONS: (2.1.10)

28 INDOOR OUTDOOR GRADE APPLICABLE TO MACHINE:

29 HEATED UNDER ROOF MEZZANINE SEE SPECIFICATION

30 UNHEATED PARTIAL SIDES APPLICABLE TO NEIGHBORHOOD:

31 ELEC. AREA CLASSIFICATION (2.1.15) CL GR DIV SEE SPECIFICATION

32 WINTERIZATION REQ'D. (2.1.9) TROPICALIZATION REQ'D. ACOUSTIC HOUSING: YES NO

33 SITE DATA: (3.4.6.6) APPLICABLE SPECIFICATIONS:

34 ELEVATION m BAROMETER BAR API 617, CENTRIFUGAL COMPR. FOR GEN. REFINERY SERV.

35 RANGE OF AMBIENT TEMPS: VENDOR HAVING UNIT RESPONSIBILITY (2.9.1.7)

36 DRY BULB WET BULB

37 NORMAL °C GOVERING SPECIFICATION (IF DIFFERENT)

38 MAXIMUM °C

39 MINIMUM °C PAINTING:

40 °C MANUFACTURER'S STD.

41 UNUSUAL CONDITIONS: DUST FUMES OTHER

42 OTHER (2.1.9)

43 SHIPMENT: (4.4.1)

44 DOMESTIC EXPORT EXPORT BOXING REQ'D.

45 REMARKS: OUTDOOR STORAGE MORE THAN 6 MONTHS (4.4.1)

46 SPARE ROTOR ASSEMBLY PACKAGED FOR (4.4.3.10)

47 HORIZONTAL STORAGE VERTICAL STORAGE

48

49

50

51

07/96 EF-050-90.09-M SHT 2 OF 6 API617SI.XLS REV 0

 Brown & Root, Inc.
JOB NO. 0 ITEM NO.
CENTRIFUGAL COMPRESSOR REVISION NO. 0 DATE ###
DATA SHEET (API 617-6TH) PAGE 3 OF 6 BY 0
SI UNITS
1 CONSTRUCTION FEATURES

2 SPEEDS: TYPE (OPEN, ENCLOSED, ETC.)

3 MAX. CONT. RPM TRIP RPM TYPE FABRICATION

4 MAX. TIP SPEEDS: m/s @ 100% SPEED MATERIAL

5 m/s @ MAX. CONT. SPEED MAX. YIELD STRENGTH (N)

6 LATERAL CRITICAL SPEEDS (DAMPED) BRINNEL HARDNESS: MAX MIN

7 FIRST CRITICAL RPM MODE SMALLEST TIP INTERNAL WIDTH (mm)

8 SECOND CRITICAL RPM MODE MAX. MACH. NO. @ IMPELLER EYE

9 THIRD CRITICAL RPM MODE MAX. IMPELLER HEAD @ 100% SPD (N-m/kg)

10 FOURTH CRITICAL RPM MODE SHAFT:

11 TRAIN LATERAL ANALYSIS REQUIRED (2.9.2.3) MATERIAL

12 TRAIN TORSIONAL ANALYSIS REQUIRED DIA @ IMPELLERS (mm) DIA @ COUPLING (mm)

13 (TURBINE DRIVEN TRAIN) (2.9.4.5) SHAFT END: TAPERED CYLINDRICAL

14 TORSIONAL CRITICAL SPEEDS: MAX. YIELD STRENGTH (N)

15 FIRST CRITICAL RPM SHAFT HARDNESS (BNH)(Rc)

16 SECOND CRITICAL RPM MAX TORQUE CAPABILITY (N-m)

17 THIRD CRITICAL RPM BALANCE PISTON:

18 FOURTH CRITICAL RPM MATERIAL AREA (mm²)

19 VIBRATION: FIXATION METHOD

20 ALLOWABLE TEST LEVEL m SHAFT SLEEVES :

21 (PEAK TO PEAK) AT INTERSTG. CLOSE MATL

22 ROTATION, VIEWED FROM DRIVEN END CW CCW CLEARENCE POINTS

23 MATERIALS INSPECTION REQUIREMENTS (4.2.2) AT SHAFT SEALS MATL

24 SPECIAL CHARPY TESTING (2.11.3) ACCESSILBLE (2.8.2)

25 RADIOGRAPHY REQUIRED FOR LABYRINTHS:

26 ULTRASONIC REQUIRED FOR INTERSTAGE

27 MAGNETIC PARTICLE REQUIRED FOR TYPE MATERIAL

28 LIQUID PENETRANT REQUIRED FOR BALANCE PISTON

29 CASING: TYPE MATERIAL

30 MODEL SHAFT SEALS:

31 CASING SPLIT SEAL TYPE (2.8.3)

32 MATERIAL SETTLING OUT PRESSURE (BARG)(kPaG)

33 THICKNESS (mm) CORR. ALLOW. (mm) SPECIAL OPERATION (2.8.1)

34 MAX. WORKING PRESS (BARG)(kPaG) SUPPLEMENTAL DEVICE REQUIRED FOR CONTACT

35 MAX DESIGN PRESS (BARG)(kPaG) SEALS (2.8.3.2) TYPE

36 TEST PRESS (BARG)(kPaG): HELIUM HYDRO BUFFER GAS SYSTEM REQUIRED (2.8.7) MANIFOLD (3.5.1.6)

37 MAX OPER. TEMP. °C MIN. OPER. TEMP. °C TYPE BUFFER GAS

38 MAX NO. OF IMPELLERS FOR CASING BUFFER GAS CONTROL SYSTEM SCHEMATIC BY VENDOR

39 MAX CASING CAPACITY (m³/h) PRESSURIZING GAS FOR SUBATMOSPHERIC SEALS (2.8.8)

40 CASING SPLIT SEALING (2.2.10) TYPE SEAL

41 SYSTEM RELIEF VALVE SET PT. (2.2.4) (BARG)(kPaG) INNER OIL LEAKAGE GUAR. (l /DAY/SEAL)

42 DIAPHRAGMS: BUFFER GAS REQUIRED FOR:

43 MATERIAL AIR RUN-IN OTHER

44 IMPELLERS: BUFFER GAS FLOW (PER SEAL):

45 NO. DIAMETERS NORM: kg/MIN @ (BAR)(kPa) DP

46 NO. VANES EA. IMPELLER MAX. kg/MIN @ (BAR)(kPa) DP

47 BEARING HOUSING CONSTRUCTION:

48 TYPE (SEPARATE, INTEGRAL) SPLIT

49 MATERIAL

50

51

07/96 EF-050-90.09-M SHT 3 OF 6 API617SI.XLS REV 0

 Brown & Root, Inc.
JOB NO. 0 ITEM NO.
CENTRIFUGAL COMPRESSOR REVISION NO. 0 DATE ###
DATA SHEET (API 617-6TH) PAGE 4 OF 6 BY 0
SI UNITS
1 CONSTRUCTION FEATURES (CONTINUED)

2 BEARINGS AND BEARING HOUSINGS

3 RADIAL INLET EXHAUST THRUST ACTIVE INACTIVE

4 TYPE TYPE

5 MANUFACTURER MANUFACTURER

6 LENGTH (mm) UNIT LOADING (MAX BAR)

7 SHAFT DIA. (mm) UNIT LOAD (ULT.) (BAR)

8 UNIT LOAD (ACT/ALLOW) AREA (mm²)

9 BASE MATERIAL NO. PADS

10 BABBIT THICKNESS (mm) PIVOT: CENTER / OFFSET, %

11 NO. PADS PAD BASE MATL

12 LOAD: B'TWN/ON PAD LUBRICATION: FLOODED DIRECTED

13 PIVOT: CTR/OFFSET, % THRUST COLLAR: INTEGRAL REPLACEABLE

14 MATERIAL

15 BEARING SPAN mm SEE ATTACHED API-670

16 BEARING TEMPERATURE DEVICES SEE ATTACHED VIBRATION DETECTORS: DATA SHEET

17 THERMISTORS API-670 DATA SHT TYPE MODEL

18 TYPE POS TEMP COEFF NEG TEMP COEFF MFR

19 TEMP SWITCH & INDICATOR BY: PURCH MFR NO. AT EA SHAFT BEARING TOTAL NO.

20 THERMOCOUPLES OSCILLATOR-DETECTORS SUPPLIED BY

21 SELECTOR SWITCH & INDIC. BY: PURCH MFR MFR MODEL

22 RESISTANCE TEMP DETECTORS MONITOR SUPPLIED BY (3.4.7.2)

23 RESISTANCE MAT'L OHMS LOCATION ENCLOSURE

24 SELECTOR SWITCH & INDICATOR BY: MFR. MODEL

25 PURCH MFR SCALE RGE ALARM SET @ m

26 LOCATION-JOURNAL BRG SHTDWN: SET @ m TIME DELAY SEC

27 NO. EA PAD EVERY OTH PAD PER BRG

28 OTHER AXIAL POSITION DETECTOR: SEE ATTACH. API-670

29 LOCATION-THRUST BRG DATA SHEET

30 NO. EA PAD EVERY OTH PAD PER BRG TYPE MODEL

31 OTHER MFR NO. REQUIRED

32 NO. (INACT) EA PAD EVERY OTH PAD PER BRG OSCILLATOR-DEMODULATOR SUPPLIED BY

33 OTHER MFR MODEL

34 MONITOR SUPPLIED BY (3.4.7.4) MONITOR SUPPLIED BY (3.4.7.2)

35 LOCATION ENCLOSURE LOCATION ENCLOSURE

36 MFR. MODEL MFR. MODEL

37 SCALE RGE ALARM SET @ °C SCALE RGE ALARM SET @ m

38 SHTDWN SET @ °C TIME DELAY SEC SHTDWN: SET @ m TIME DELAY SEC

39 CASING CONNECTIONS

40 DESIGN ASME

41 APPROVAL API605 FLANGED MATING FLG GAS

42 CONNECTION REQ'D OTHERS FACING POSITION OR & GASKET VELOCITY

43 (2.11.2.10) SIZE (2.4.2.1) STUDDED BY VENDOR m/SEC

44 (2.4.2.1) (2.4.2.3)

45 INLET

46 DISCHARGE

47

48

49

50

51

07/96 EF-050-90.09-M SHT 4 OF 6 API617SI.XLS REV 0

 Brown & Root, Inc.
JOB NO. 0 ITEM NO.
CENTRIFUGAL COMPRESSOR REVISION NO. 0 DATE ###
DATA SHEET (API 617-6TH) PAGE 5 OF 6 BY 0
SI UNITS
1 OTHER CONNECTIONS ALLOWABLE PIPING FORCES AND MOMENTS:

2 SERVICE: NO. SIZE TYPE INLET DISCHARGE

3 LUBE-OIL INLET FORCE MOMT FORCE MOMT FORCE MOMT

4 LUBE OIL OUTLET N N-m N N-m N N-m

5 SEAL-OIL INLET AXIAL

6 SEAL-OIL OUTLET VERTICAL

7 SEAL GAS INLET HORIZ. 90

8 SEAL GAS OUTLET FORCE MOMT FORCE MOMT FORCE MOMT

9 CASING DRAINS N N-m N N-m N N-m

10 STAGE DRAINS AXIAL

11 VENTS VERTICAL

12 COOLING WATER HORIZ. 90

13 PRESSURE ACCELEROMETER(3.4.7.5)

14 TEMPERATURE SEE ATTACHED API-670 DATA SHEET

15 SOLVENT INJECTION TYPE MODEL

16 PURGE FOR: MFR NO. REQUIRED

17 BRG. HOUSING LOCATION

18 BTWN BRG & SEAL OSCILATOR-DEMODULATORS SUPPLIED BY

19 BTWN SEAL & GAS MFR MODEL

20 INDIVIDUAL STAGE DRAINS REQUIRED (2.4.3.2) MONITOR SUPPLIED BY (3.4.7.6)

21 VALVED & BLINDED LOCATION ENCLOSURE

22 VALVED & BLINDED & MANIFOLD MFR MODEL

23 KEY PHASOR REQUIRED SCALE RANGE ALARM SET @ mm/SEC²

24 COMPRESSOR GEAR DRIVER SHTDWN SET @ mm/SEC² TIME DELAY SEC

25 ACCESSORIES

26 COUPLING AND GUARDS (3.2)

27 NOTE: SEE ROTATING ELEMENTS - SHAFT ENDS

28 SEE ATTACHED API-671 DATA SHEET KEYLESS HYDRAULIC KEYED

29 COUPLING FURNISHED BY

30 MANUFACTURER TYPE MODEL

31 COUPLING GUARD FURNISHED BY:

32 TYPE: FULLY ENCLOSED SEMI-OPEN OTHER

33 COUPLING DETAILS VENDOR MOUNT HALF COUPLING

34 MAX O.D. mm LUBRICATION REQUIREMENTS:

35 HUB WEIGHT kg NON-LUBE GREASE CONT. OIL LUBE OTHER

36 SPACER LENGTH mm QUANTITY PER HUB kgs or L/MIN

37 SPACER WEIGHT kg

38 MOUNTING PLATES

39 BASEPLATES: FURNISHED BY (3.3.1.1) SOLEPLATES: FURNISHED BY:

40 COMPRESSOR ONLY (3.3.2.1) DRIVER GEAR THICKNESS mm

41 OTHER SUBSOLE PLATES REQ'D (3.3.3.2)

42 DRIP TRIM LEVELING PADS (3.3.2.2) STAINLESS STEEL SHIM THICKNESS - mm

43 COLUMN MOUNTING (3.3.2.3) DRIVER GEAR COMPRESSOR

44 SUB-SOLE PLATES REQ'D (3.3.3.2) PRIMER FOR EPOXY GROUT REQ'D (3.3.1.2.9)

45 STAINLESS STEEL SHIM THICKNESS mm TYPE

46 PRIMER FOR EPOXY GROUT REQ'D (3.3.1.2.9)

47 TYPE

48

49 BASE PLATE WILL BE ON CONCRETE FOUNDATION (3.3.2.5)

50 MACHINED MOUNTING PADS REQ'D. (3.3.2.6)

51

07/96 EF-050-90.09-M SHT 5 OF 6 API617SI.XLS REV 0

 Brown & Root, Inc.
JOB NO. 0 ITEM NO.
CENTRIFUGAL COMPRESSOR REVISION NO. 0 DATE ###
DATA SHEET (API 617-6TH) PAGE 6 OF 6 BY 0
SI UNITS
1 UTILITIES

2 UTILITY CONDITIONS: TOTAL UTILITY CONSUMPTION:

3 STEAM: DRIVERS HEATING COOLING WATER m³/h

4 INLET MIN BARG(kPaG) °C BARG(kPaG) °C STEAM, NORMAL kg/h

5 NORM BARG(kPaG) °C BARG(kPaG) °C STEAM, MAX kg/h

6 MAX BARG(kPaG) °C BARG(kPaG) °C INSTRUMENT AIR m³/h

7 EXHAUST. MIN BARG(kPaG) °C BARG(kPaG) °C HP (DRIVER) kW

8 NORM BARG(kPaG) °C BARG(kPaG) °C HP (AUXILIARIES) kW

9 MAX BARG(kPaG) °C BARG(kPaG) °C HEATERS KW

10 ELECTRICITY: (3.4.6.1) PURGE (AIR OR N2) m³/h

11 DRIVERS HEATING CONTROL SHUTDOWN MISCELLANEOUS:

12 VOLTAGE RECOMMENDED STRAIGHT RUN OF PIPE DIAMETERS

13 HERTZ BEFORE SUCTION

14 PHASE NOMOGRAPHS REQUIRED FOR EACH SECTION (5.3.3.1.5)

15 COOLING WATER: VENDOR'S REVIEW & COMMENTS ON PURCHASER'S

16 TEMP. INLET °C MAX RETURN °C PIPING & FOUNDATION (3.5.3.2)

17 PRESS NORM BARG(kPaG ) COMPRESSOR TO BE SUITABLE FOR FIELD RUN IN

18 DESIGN BARG(kPaG) ON AIR (2.1.17)

19 MIN RETURN BARG(kPaG) PROVISION FOR LIQUID INJECTION (2.1.11)

20 MAX ALLOW D P BAR(kPa)

21 WATER SOURCE VENDOR'S REVIEW & COMMENTS ON PURCHASER'S

22 INSTRUMENT AIR: CONTROL SYSTEMS (3.4.1.1)

23 MAX PRESS BARG(kPaG) MIN PRESS BARG(kPaG) EXTENT OF PROCESS PIPING BY VENDOR (3.5.3.1)

24 SHOP INSPECTION AND TESTS: (4.1.4) REQ'D. SHOP FITUP OF VENDOR PROCESS PIPING (4.4.3.11)

25 CLEANLINES (4.2.1.5) WELDING HARDNESS TESTING (4.2.1.6)

26 HYDROSTATIC X
2

27 IMPELLER OVERSPEED X VENDOR'S REPRESENTATIVE SHALL (2.1.14)

28 MECHANICAL RUN X OBSERVE FLANGE PARTING

29 CONTRACT COUPLING IDLING ADAPTORS CHECK ALIGNMENT AT TEMPERATURE

30 CONTRACT PROBES SHOP PROBES BE PRESENT AT INITIAL ALIGNMENT

31 VARY LUBE & SEAL OIL PRESSURES WEIGHTS (kg):

32 AND TEMPERATURES (4.3.4.2.5) COMPR. GEAR DRIVER BASE

33 POLAR FORM VIB DATA (4.3.4.3.3) ROTORS: COMPR. DRIVER GEAR

34 TAPE RECORD VIB DATA (4.3.4.3.6) COMPRESSOR UPPER CASE

35 TAPE DATA TO PURCHASER (4.3.4.3.7) SOUR SEAL OIL TRAPS

36 SHAFT END SEAL INSP (4.3.4.4.1) L.O. CONSOLE S.O. CONSOLE

37 GAS LEAK TEST DISCH PRESS (4.3.5.2) OVERHEAD SEAL OIL TANKS

38 BEFORE AFTER POST TEST INSPECTION (4.3.6.8) MAX. FOR MAINTENANCE (IDENTIFY)

39 PERFORMANCE TEST(GAS)(AIR)(4.3.6.1) TOTAL SHIPPING WEIGHT

40 COMPLETE UNIT TEST (4.3.6.2)

41 TORSIONAL VIB MEAS (4.3.6.2) SPACE REQUIREMENTS (mm):

42 TANDEM TEST (4.3.6.3) COMPLETE UNIT: L W H

43 GEAR TEST (4.3.6.4) L.O. CONSOLE: L W H

44 HELIUM LEAK TEST (4.3.6.5) S.O. CONSOLE: L W H

45 SOUND LEVEL TEST (4.3.6.6) SOUR SEAL OIL TRAPS

46 FULL LOAD / SPEED / PRESS TEST (4.3.6.9) OVERHEAD SEAL OIL TANKS

47 HYDRAULIC COUPLING INSP (4.3.6.10)

48 REMARKS:

49

50

51

07/96 EF-050-90.09-M SHT 6 OF 6 API617SI.XLS REV 0