ASSOC.

PIP
DATA SHEET RESP73-D
RESP73H/V
PAGE 1 OF 3
ASME CENTRIFUGAL PUMPS (US CUSTOMARY UNITS)
FEBRUARY 2007
1 ISSUED FOR: PROPOSAL PURCHASE AS BUILT
2 FACILITY NAME/LOCATION:
3 ITEM NAME: PURCHASER/LOCATION:
4 ITEM TAG NO.: JOB NO:
5 SERVICE: PURCHASER ORDER NO.:
6 UNIT: SUPPLIER/LOCATION:
7 P&ID NO.: SUPPLIER ORDER/SERIAL NOS.: /

8 DATA PROVIDED BY: PURCHASER SUPPLIER u SUPPLIER IF NOT BY PURCHASER

9 GENERAL
10 NO. PUMPS REQ.: u PUMP SIZE: u PUMP MODEL: u PUMP TYPE:
11 NUMBER MOTOR DRIVEN: NUMBER TURBINE DRIVEN: GEARBOX ITEM NUMBER:
12 MOTOR ITEM NUMBER: TURBINE ITEM NUMBER: GEARBOX PROVIDED BY:
13 MOTOR PROVIDED BY: TURBINE PROVIDED BY: GEARBOX MOUNTED BY:
14 MOTOR MOUNTED BY: TURBINE MOUNTED BY:

15 OPERATING CONDITIONS PERFORMANCE

16 RATED MAX. NORMAL MIN. PERFORMANCE CURVE NO.: u SPEED: RPM
17 CAPACITY: GPM MEASURED AT CAPY.: RATED MAX. NORMAL MIN.
18 SUCTION PRESSURE: PSIG NPSH REQ’D.: FT
19 DISCHARGE PRESSURE: PSIG TOTAL DIFFERENTIAL HEAD @ RATED IMPELLER: FT
20 DIFFERENTIAL PRESSURE: PSI MAX. DIFFERENTIAL HEAD @ RATED IMPELLER: FT
21 DIFFERENTIAL HEAD: FT @ MINIMUM S.G. MINIMUM CONTINUOUS FLOW:
22 HYDRAULIC POWER: HP THERMAL: GPM STABLE: GPM
23 OPERATING TIME: HR/YR ALLOWABLE OPERATING REGION: TO: GPM
24 NPSH AVAILABLE: FT.
25 SUCTION SPECIFIC SPEED, MAXIMUM BEST EFFICIENCY POINT FOR RATED IMPELLER: GPM
26 SYSTEM DESIGN: SUCTION SPECIFIC SPEED:
27 STAND ALONE OPERATION PARALLEL OPERATION IMPELLER DIA.: RATED: MAX.: MIN.: IN
28 SERIES OPERATION WITH ITEM NUMBER: PUMP RATED POWER: BHP EFFICIENCY: %
29 SUCTION PRESSURE: MIN./MAX.: / PSIG MAXIMUM POWER @ RATED IMPELLER: BHP
30 SERVICE:
31 CONTINUOUS INTERMITTENT: STARTS/DAY
32 SYSTEM CONTROL METHOD: CASE PRESSURE RATING:
33 SPEED FLOW LEVEL TEMPERATURE MAX. ALLOWABLE WORKING PRES.: PSIG @ °F
34 PRESSURE PIPE FRICTION RESISTANCE ONLY HYDROSTATIC TEST PRESSURE: PSIG

35 PUMPED FLUID SITE CONDITIONS

36 PUMPED FLUID: LOCATION:
37 RATED MAX. NORMAL MIN. INDOOR OUTDOOR
38 PUMPING TEMP.: °F ALTITUDE: FT
39 AT DESIGNATED TEMP.: RATED MAX. NORMAL MIN. RANGE OF AMBIENT TEMPS.: MIN./MAX.: / °F
40 SPECIFIC GRAVITY: ELECTRICAL CLASSIFICATION:
41 VAPOR PRESSURE: PSIA CL.: GR.: DIV.:
42 VISCOSITY: CP NON HAZARDOUS
43 SPECIFIC HEAT: BTU/LB°F GENERAL REMARKS
44 INITIAL BOILING POINT: °F @ PSIA
45 LIQUID: HAZARDOUS FLAMMABLE
46 OTHER:
47
48
49 CORROSION / EROSION CAUSED BY:
50 % SOLID: MAX. PARTICLE SIZE: IN
51
52 NO. DATE REVISION DESCRIPTION BY APVD.
53
54
55
 ASSOC. PIP
DATA SHEET RESP73-D
RESP73H/V
PAGE 2 OF 3
ASME CENTRIFUGAL PUMPS (US CUSTOMARY UNITS)
FEBRUARY 2007
1 MECHANICAL DATA u COUPLING BETWEEN PUMP AND DRIVER
2 u IMPELLER TYPE: MANUFACTURER:
3 CLOSED OPEN SEMI-OPEN TYPE:
4 OTHER: SIZE:
5 u CASING MOUNTING: MODEL:
6 FOOT CENTERLINE SPACER LENGTH: IN
7 VERTICAL IN-LINE CLOSE-COUPLED COUPLING GUARD TYPE:
8 BEARINGS: MANUFACTURER’S STANDARD
9 u BEARING MANUFACTURER: BASEPLATE MOUNTED
10 RADIAL BEARING TYPE: NO. NON-SPARK COUPLING GUARD REQUIRED
11 THRUST BEARING TYPE: NO. REMARKS:
12 u BEARING ISOLATORS:
13 SHAFT STIFFNESS RATIO (L 3/D4):

14 LUBRICATION: BASEPLATE
15 FLOOD PURE MIST SHIELDED (GREASE) TYPE: GROUTED FREE STANDING
16 GREASE PURGE MIST SEALED (GREASE) PRECAST POLYMERS
17 CONSTANT LEVEL OILER REQUIRED u CENTERLINE OF PUMP TO STILT BOTTOM: IN
18 HOUSING VENT REQUIRED VERTICAL PUMP CASE SUPPORT BRACKET
19 MAGNETIC DRAIN PLUG IN HOUSING REQUIRED DESIGN: PIP STANDARD RESP002 (DATA SHEET ATTACHED)
20 u OIL COOLER REQUIRED MANUFACTURER’S STANDARD
21 SEAL SPRAY GUARD REQUIRED REMARKS:
22 u OIL VISCOSITY: ISO GRADE: OTHER:
23 NOZZLE CONNECTIONS: PAINT AND SHIPMENT PREPARATION
24 SIZE u RATING u FACING PUMP: BASEPLATE:
25 SUCTION: MANUFACTURER’S STD. MANUFACTURER’S STD.
26 DISCHARGE: OTHER: OTHER:
27 AUX. CASE CONNECTION: DRAIN REQUIRED SHIPMENT:
28 u SIZE: IN DOMESTIC EXPORT EXPORT BOXING REQ'D.
29 THREADED WELDED & FLANGED NUMBER OF MONTHS OF STORAGE:
30 u MATERIALS TOTAL WEIGHT: LBS
31 MATERIAL CLASS CODE:
32 CASING: INSPECTION AND TESTING
33 IMPELLER: FINAL INSPECT. REQD.: DAYS NOTIFICATION REQD.:
34 COVER: TEST: NON.-WITNESSED WITNESSED CERTIFICATE
35 SHAFT: HYDROSTATIC:
36 SHAFT SLEEVE: PERFORMANCE:
37 BASEPLATE: NPSHR:
38 CASING GASKET: VIBRATION:
39 IMPELLER GASKET: OTHER:
40 CASING FASTENERS IF NOT PER 4.8.1: DISMANTLE AND INSPECT AFTER TEST
41 BEARING HOUSING: CASTING REPAIR PROCEDURE APPROVAL REQUIRED
42 BEARING HOUSING ADAPTER: MATERIAL CERTIFICATION REQUIRED:
43 BEARING HOUSING END SEALS: CASING COVER IMPELLER SHAFT
44 COUPLING GUARD: OTHER:
45 MECH. SEAL GLAND: INSPECTION REQUIRED FOR CONNECTION WELDS:
46 MECH. SEAL GLAND FASTENERS: MANUFACTURER’S STANDARD VISUAL INSPECTION
47 O-RING MATERIAL (4.6.1.3): INSPECTION REQUIRED FOR CASTINGS:
48 MANUFACTURER’S STANDARD VISUAL INSPECTION
49 u DRIVER OTHER:

50 HORSEPOWER RATING: HP SPEED: RPM MANUFACTURER DOCUMENTATION REQUIREMENTS

51 DRIVE HP SELECTED FOR MAX. S.G.: & MAX. VISC.: CP FOR SUPPLIER DATA REQUIREMENTS REFER TO:
52 REMARKS: REMARKS:
53
54
55
 ASSOC. PIP
DATA SHEET RESP73-D
RESP73H/V
PAGE 3 OF 3
ASME CENTRIFUGAL PUMPS (US CUSTOMARY UNITS)
FEBRUARY 2007
1 MECHANICAL SEAL BARRIER/BUFFER FLUSH SYSTEM
2 FURNISHED BY: SUPPLIER PURCHASER BARRIER FLUSH PLAN NO.:
3 MOUNTED BY: SUPPLIER PURCHASER BARRIER FLUSH LIQUID:
4 u SEAL CLASSIFICATION CODE: TEMPERATURE MIN./MAX.: / °F
5 u MANUFACTURER: SPECIFIC GRAVITY:
6 u MODEL: SPECIFIC HEAT: BTU/LB °F
7 u MANUFACTURER CODE: VAPOR PRESSURE: PSIA @ °F
8 SEAL TYPE: CARTRIDGE COMPONENT u PRESSURE REQD. MIN./MAX.: / PSIG
9 SEAL DESIGN: SINGLE DUAL DRY GAS MAWP OF SECONDARY SEAL SYSTEM: PSIG
10 PRESSURIZED UNPRESSURIZED TEMP. REQD. MIN./MAX.: / °F
11 SEAL CHAMBER: TAPER BORE CYLINDRICAL BORE SECONDARY SEAL FLUSH PIPING:
12 SEAL CHAMBER SIZE: OVERSIZED STANDARD TUBING PIPE OTHER:
13 u SLEEVE MATERIAL: MATERIAL:
14 u PUMPING RING REQUIRED: 316 SS CARBON STEEL OTHER:
15 u THROAT BUSHING REQUIRED: PIPING/TUBING SIZE: IN
16 MATERIALS: PIPING ASSEMBLY:
17 u REMARKS: THREADED UNIONS FLANGED
18 TUBE TYPE FITTINGS SOCKET WELDED
19 SEAL POT IF NOT PER 4.6.7.1:
20 u REMARKS:
21 SEAL GLAND
22 TAPS REQUIRED: QUENCH FLUSH DRAIN
23 OTHER: SEAL SYSTEM INSTRUMENTATION
24 u THROTTLE BUSHING: PRIMARY SEALS: GAUGES SWITCHES TRANSMITTERS
25 MATERIALS: FLOW:
26 TEMPERATURE:
27 SEAL FLUSHING PRESSURE:
28 PRIMARY FLUSH PLAN NO.: SECONDARY SEALS:
29 EXTERNAL FLUSH LIQUID: FLOW:
30 SUPPLY TEMP. MIN./MAX.: / °F PRESSURE:
31 SPECIFIC GRAVITY: LEVEL:
32 SPECIFIC HEAT: BTU/LB °F REMARKS:
33 VAPOR PRESSURE: PSIA @ °F
34 FLOW RATE REQD. MIN./MAX.: / GPM
35 PRESSURE REQD. MIN./MAX.: / PSIG
36 TEMP. REQD. MIN./MAX.: / °F COOLING OR HEATING PIPING PLANS
37 PRIMARY SEAL FLUSH PIPING: PIPING PLAN NO.:
38 TUBING PIPE OTHER: NAME OF FLUID:
39 MATERIAL: INLET TEMPERATURE: °F
40 316 SS CARBON STEEL OTHER: OUTLET TEMPERATURE: °F
41 PIPING/TUBING SIZE: IN RATED FLOW: GPM
42 PIPING ASSEMBLY: SUPPLY PRESSURE: PSIG
43 THREADED UNIONS FLANGED MAX. ALLOWABLE ΔP: PSI
44 TUBE TYPE FITTINGS SOCKET WELDED
45 GALVANIZED PIPE SS TUBING
46 u REMARKS: SIGHT FLOW INDICATOR
47 OUTLET SHUT-OFF VALVE
48 u REMARKS:
49
50
51
52
53
54
55