Cemfair FD

One component polymer modified cemen ous fairing coat and cosme c repair mortar

Description
Technical Properties @ 250C:
Cemfair FD is a one component acrylic polymer modified
Colour: Grey & white
powder. When mixed with water Cemfair FD produces a
highly consistent, smooth, fine, trowellable mortar. Fresh wet density: 1.75 ± 0.10 g/cm³
Maximum aggregate
Applications 0.1 mm
size:
 For fair face concrete repair. Applica on tempera-
 As a thin layer render. 5 - 35oC
ture:
 As a skim coat for pin holes and minor honeycombed
concrete repair. Applica on thickness: Up to 3 mm
 As pore sealer and leveling mortar. Flexural strength:
 To produce a uniform surface for subsequent paint ≥ 3 MPa @ 28 days
ASTM C348
finish.
Tensile strength:
≥ 1.2 MPa @ 28 days
Advantages BS 6319-7
VOC:
 Shrinkage controlled polymer modified cemen ous ≤ 10 g/ltr
ASTM D2369
repair mortar which reduces any poten al cracking.
 Easy to apply, single component which requires only EN 1504-3
addi on of water. Measured
Property requirement for
 Excellent adhesion to concrete, no independent value
Class R2
primer or curing is required.
Compressive
 Compa ble with other types of protec ve coa ngs.
strength: ≥ 15 MPa Pass
 Can be applied to feather edge thicknesses.
EN 12190
 Suitable for internal and external applica ons.
 Cost effec ve, hand applied no formwork is required. Adhesion bond:
≥ 0.8 MPa Pass
EN 1542
Standards Thermal
compa bility freeze/
≥ 0.8 MPa Pass
Cemfair FD complies with the requirement of EN 1504-3 thaw:
as non-structural repair mortar of class R2. EN 13687-1
Chloride ion content:
≤ 0.05% Pass
Method of Use EN 1015-17
Complies
Substrate Preparation Dangers substance:
with 5.4

All surfaces should be clean, sound and uncontaminated Mixing

prior to the applica on of Cemfair FD. The prepared
area should be cleaned thoroughly by brush and/or To ensure proper mixing, a mechanically powered mixer
compressed air. The prepared area should be soaked with or drill fi ed with suitable paddle should be used.
water immediately prior to the applica on of Cemfair FD. However for small quan es, Cemfair FD can be hand
mixed using proper tools and bucket.
Priming
For one full bag, 6.75 - 8.00 litre of fresh water should be
No independent primer is required. added to a clean container.
Cemfair FD
The powder is then added slowly to the water while Cautions
mixing con nuously with low speed mixer/drill (400 - 600
rpm). Mixing me should be con nued for 3 minutes Health and Safety
un l uniform consistency is obtained.
As a powder containing Portland cement, Cemfair FD may
To enhance the scratch resistance of Cemfair FD, an cause irrita on to skin or eyes.
addi on of Cempatch SBR or Cempatch SBR100 is In case of accidental contact with eyes, immediately flush
advisable. 50% of the total mixing water shall be replaced with plenty of water for at least 10 minutes and seek
by Cempatch SBR range. medical advise if necessary.

Placing and Finishing For further informa on refer to the Material Safety Data
Sheet.
Cemfair FD can be applied by steel trowel. The mixed
mortar can be applied to the prepared substrates at up to Fire
3 mm thicknesses. The applied mortar should be allowed
to s ffen before trowelling to a smoother finish. Cemfair FD is nonflammable.

Curing More from Don Construction Products

Curing is not required for Cemfair FD in normal ambient A wide range of construc on chemical products are
condi ons. In the case of harsh weather condi ons, such manufactured by DCP which include:
as high wind and temperatures, it is recommended to
cure with Setseal A or wet hessian with polyethelene.  Concrete admixtures.
 Surface treatments
Cleaning  Grouts and anchors.
 Concrete repair.
All tools should be cleaned immediately a er finishing  Flooring systems.
with water. Hardened materials can be cleaned  Protec ve coa ngs.
mechanically.  Sealants.
 Waterproofing.
Packaging  Adhesives.
 Tile adhesives and grouts.
Cemfair FD is available in 25 kg bags.  Building products.
 Structural strengthening.
Thicknesses and Size Limitations

Cemfair FD can be applied by single applica on from

feather edge to 3 mm thickness. Higher thicknesses can
be achieved by applying mul ple layers.

Yield

Approximately 19 litre per 25 kg bag.

Storage

Cemfair FD has a shelf life of 12 months from date of

manufacture if stored at temperatures between 2°C and
35°C.

If these condi ons are exceeded, DCP Technical

Department should be contacted for advise.

Note:
04-0002-A-2020

tĞĞŶĚĞĂǀŽƵƌƚŽĞŶƐƵƌĞƚŚĂƚĂŶLJŝŶĨŽƌŵĂƟŽŶ͕ĂĚǀŝĐĞŽƌƌĞĐŽŵŵĞŶĚĂƟŽŶǁĞŵĂLJŐŝǀĞŝŶ
ƉƌŽĚƵĐƚ ůŝƚĞƌĂƚƵƌĞ ŝƐ ĂĐĐƵƌĂƚĞ ĂŶĚ ĐŽƌƌĞĐƚ͘ ,ŽǁĞǀĞƌ͕ ďĞĐĂƵƐĞ ǁĞ ŚĂǀĞ ŶŽ ĐŽŶƚƌŽů ŽǀĞƌ
ǁŚĞƌĞĂŶĚŚŽǁƉƌŽĚƵĐƚƐĂƌĞĂƉƉůŝĞĚ͕ǁĞĐĂŶŶŽƚĂĐĐĞƉƚĂŶLJůŝĂďŝůŝƚLJĂƌŝƐŝŶŐĨƌŽŵƚŚĞƵƐĞŽĨ
ƚŚĞƉƌŽĚƵĐƚƐ͘