40_50L2546/56 Service manual

Caution
Be sure to read this manual before servicing. To ensure safety from fire, electric shock, injury, harmful
radiation and materials, various measures are provided in this LCD Television.
Be sure to read cautionary items described in the manual before servicing.
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric
shock, do not perform any servicing other than that described in the operating instructions unless you are
qualified to do so.

Service Warning
1. Since the Panel Module and the front Filter are made of glass, handling the broken Module and Filter
carefully and with caution in order not to receive injury.
2. Replacement work should be started after the Panel Module and the AC/DC Power supply have become
sufficiently cool.
3. Special care should be taken when working near the display area in order not to damage its surface.
4. The Panel Module should not be touched with bare hands in order to protect its surface from blemishes
and damage.
5. It is recommended that you use clean soft gloves during the replacement work in order to protect not only
the display area of the Panel Module but also yourself.

Contents
1. Features……………………………3 6.
2. 2. Specifications………………………4 Service points………………………..13
3. Component names…………..…….9 7. Adjustment…………………….……..14
4. Side Inputs………………….……..10 8. TTroubleshooting……………………..20
5. Remote Control……………….…..11

1
 CAUTION FOR SAFETY
Please read this page before repair the monitor.
The following safety precautions are designed to help you stay safe and prevent accidents during the repair
work.
z Please take note of these cautionary flags.

Warning This means "Potential to sustain injury or even death."

Caution This means "Potential to sustain breakage or irreparable damage."

z Also note these cautionary icons

This means "CAUTION" This means "MUST"

This means "POTENTIAL ELECTRIC

This means "DO NOT"
SHOCK"

WARNING
„ Follow instructions. „ Must use same types of wires and
components.
The cabinet, chassis, and labels are parts The Monitor uses special tubes and tapes
that require attention. You must follow the made from insulated materials. Moreover,
caution notes and safety instructions some materials are kept from making
presented throughout this User Manual to contact with the PWB for the sake of
prevent damage to them or injury to safety.Internal leads are kept from hot
yourself. parts or high voltage parts by means of
clamps or other measures. As such, you
„ Prevent electric shock. must restored these parts to their original
Exercise caution while working on the conditions in order to prevent electric
device as the Monitor contains high shock or fire.
voltage parts and power supply.It is
possible to sustain severe injury or death „ Perform safety check when done.
if you accidentally touch the wrong
parts.You must disconnect the power Every part (such as removed screws,
supply while servicing, reassembling, or components, and wiring) must be restored
change parts. If you touch a live to their prior conditions after servicing.Be
connection it is possible to sustain severe sure to check everything that was
injury or death. repaired for damage or mistakes. Also
measure the insulated impedance with a
„ Use recommended components. meg-ohm meter to confirm that the
Use only the recommended components impedance value is more than 4M ohm.If
or componentst that structurally identical the impedance value is less than 4M ohm,
to the originals. This is to ensure safety then electric shock or fire may result.
and reliability. Pay special attention to
parts in the parts list and circuit diagrams
„ Do not try to check the HDCP code and
marked with . If you use
non-recommended components, then combination circuit.
electric shock or fire may result. Never remove the shield case protecting
the HDCP code and combination circuit.

2
 PRECAUTIONS

z Cleaning the LCD panel of the television

Please make sure to unplug the power cord before cleaning the television.
● Wipe the panel with a lint-free and dry cloth in order to prevent damage to the panel surface.
● Do not use a chemical cloth or cleaner. Depending on the ingredients, it may cause discoloration and
damage the panel surface.
● Do not wipe with a hard cloth or rub hard. It may hurt the panel surface.
● In case of the greasy dirt such as fingerprint, wipe with a lint-free cloth moistened by a diluted neutral
detergent solution, and then wipe with a soft and dry cloth.
● Do not use a spray cleaner. It could cause malfunction.

z Cleaning the monitor's cabinet of the television

● The following may cause crack, deformation, and paint peeling.
● Do not wipe the cabinet with benzene, thinner, and other chemical products.
● Do not spray volatile solutions such as insecticide over the cabinet.
● Do not leave the cabinet in prolonged contact with plastic or rubber materials.
● Do not use a chemical cloth, cleaner or wax. Depending on the ingredients, it may cause crack and
deformation.
● Use a lint-free cloth to clean the cabinet and control panel of the television. In case of the heavy dirt,
wipe with a soft cloth moistened by a diluted neutral detergent solution, and then wipe with a soft and
dry cloth.
● Never use the following detergents. It could cause crack, discoloration, and scratch.
● Acid/ alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass
cleaner, etc.
1. Features
● Large-screen and high-definition LCD panel.
● Improved Digital signal processor.
● Accept more digital input devices with HDMI terminals.
● Great diversity of connecting terminals to cover wide range of audio-visual equipments.
● Enjoy the image from PC with large, high-definition LCD screen.
● Easy-to-use On-Screen Display system operating with Remote control.
● Low power consumption.

3
2. Specifications
SPECIFICATION 40L2546/56 50L2546/56
Display dimensions
Panel 878.112 (H) x 485.352 (V) mm 1095.84 (H) x 616.41 (V) mm
Resolution 1920(H) x 1080 (V) pixels 1920(H) x 1080 (V) pixels

including Stand: 904 (W) x 567 (H) x including Stand: 1122 (W) x 701(H) x
Net dimensions
194(D) mm 216(D) mm

Net weight including Stand: 11.0 kg including Stand: 16.5 kg

Operating: 5°C to 35°C, Storage: Operating: 5 C to 35°C, Storage: 20°C

Ambient Temperature 20°C to 80°C to 80°C
conditio
Operating: 20% to 80%, Storage: 5% Operating: 20% to 80%, Storage: 5%
ns Relative Humidity to 90% to 90%
Power supply AC 110~240V±10%, 50~60Hz±3Hz AC 110~240V±10%, 50~60Hz±3Hz
Power consumption in standby
0.4W 0.4W
mode

Audio output 7W+7W 7W+7W

(VIDEO input)

SCART :Full RGB output

Component : Y incluse composite video input terminal
Input terminals
(RCA : L/R audio input terminal (RCA)
HDMI 1,2 : HDMI input terminal

Headphone output: Socket (3.5mm)

Output signals
Optical output : SPDIF

(RF input)

ATV:NTSC/PAL/SECAM standard

RF Video System DTV:DVB-T/C/T2

DVB-S/S2 : Satellite

(RGB input)
Analog RGB input terminal (D-sub 15-pin)
Input terminals
Audio input terminal (Component L/R audio input terminal (RCA)

Input signals 0.7 V, analog RGB (Recommended Signal)

Sync signals `H/V separate, TTL level [2kΩ]

4
Video support timing
PAL 50/60Hz
Composite Video SECAM
NTSC
480i / 480p / 720p / 1080i (60Hz)
Component Video
576i / 576p / 720p / 1080i (50Hz)
VGA (640 x 480) (60Hz)
S-VGA (800 x 600) (60Hz)
XGA (1024 x 768) (60Hz)
W-XGA (1280 x 768) (60Hz)
PC Input (D-Sub)
W-XGA (1280 x 800) (60Hz)
W-XGA 1360 x 768) (60Hz)
W-XGA+ (1440 x 900) (60Hz)
S-XGA (1280 x 1024) (60Hz)
480i (60Hz) / 576i (50Hz)
480p (60Hz) / 576p (50Hz)
HDMI-
720p (24/30/50/60Hz)
Video Format
1080i (60Hz) / 1080i (50Hz)
1080p (24/30/50/60Hz)
VGA (640 x 480) (60Hz)
SVGA (800 x 600) (60Hz)
HDMI- XGA (1024 x 768) (60Hz)
PC Format WXGA (1280 x 768) (60Hz)
WXGA (1360 x 768) (60Hz)
SXGA (1280 x 1024) (60Hz)

5
PC/HDMI timing table

SYNC PIXEL SYNC BACK

FREQ PERIOD Display
POLARITY CLOCK WIDTH PORCH

Mode LINE (pixel) LINE (pixel)

LINE(kHz) LINE (pixel) LINE LINE (pixel)
(MHz) FRAME FRAME
FRAME(Hz) FIELD(lines) FIELD FRAME(lines)
(lines) (lines)

VGA 60Hz 31.469 800 Negative 25.175 640 96 40

640x480 59.941 525 Negative 480 2 25
SVGA 60Hz 37.879 1056 Positive 40 800 128 88
800x600 60.317 628 Positive 600 4 23
XGA 60Hz 48.363 1344 Negative 65 1024 136 160
1024x768 60.004 806 Negative 768 6 29
WXGA 60Hz 47.396 1440 Positive 68.25 1280 32 80
1280x768 59.995 790 Negative 768 7 12
WXGA 60Hz 47.776 1664 Negative 79.5 1280 128 192
1280x768 59.87 798 Positive 768 7 20
WXGA 60Hz 63.981 1688 Positive 108 1280 112 248
1280x1024 60.02 1066 Positive 1024 3 38
WXGA 60Hz 47.712 1792 Positive 85.5 1360 112 256
1360x768 60.015 795 Positive 768 6 18
W-XGA+ 60Hz 55.935 1904 Negative 106.5 1440 152 232
1440x900 59.887 934 Positive 900 6 25

6
HDMI Video timing table
SYNC PIXEL SYNC BACK
FREQ FREQ PERIOD Display
POLARITY CLOCK WIDTH PORCH

LINE (pixel) LINE (pixel) LINE (pixel)

LINE(kHz) LINE (pixel) LINE
MODE (MHz) FRAME FRAME FRAME
FRAME(Hz) FIELD(lines) FIELD
(lines) (lines) (lines)

59.94Hz 1440x480i 15.734 1716 Negative 27 1440 124 114

59.94 262.5 Negative 240 3 15

60Hz 1440x480i 15.75 1716 Negative 27.027 1440 124 114

60 262.5 Negative 240 3 15

50Hz 1440x576i 15.625 1728 Negative 27 1440 126 138

50 312.5 Negative 288 3 19

59.94Hz 720x480P 31.469 858 Negative 27 720 62 60

59.94 525 Negative 480 6 30

60Hz 720x480P 31.5 858 Negative 27.027 720 62 60

60 525 Negative 480 6 30

50Hz 720x576P 31.25 864 Negative 27 720 64 68

50 625 Negative 576 5 39

59.94Hz 1280x720P 44.955 1650 Positive 74.175 1280 40 220

59.939 750 Positive 720 5 20

60Hz 1280x720P 45 1650 Positive 74.25 1280 40 220

60 750 Positive 720 5 20

50Hz 1280x720P 37.5 1980 Positive 74.25 1280 40 220

60 750 Positive 720 5 20

59.94Hz 1920X1080i 33.716 2200 Positive 74.175 1920 44 148

59.94 562.5 Positive 540 5 15

60Hz 1920X1080i 33.75 2200 Positive 74.25 1920 44 148

60 562.5 Positive 540 5 15

50Hz 1920X1080i 28.125 2640 Positive 74.25 1920 44 148

50 562.5 Positive 540 5 15

59.94Hz
67.43 2200 Positive 148.352 1920 44 148
1920X1080P

59.94 1125 Positive 1080 5 36

60Hz 1920X1080P 67.5 2200 Positive 148.5 1920 44 148

60 1125 Positive 1080 5 36

50Hz 1920X1080P 56.25 2200 Positive 148.5 1920 44 148

50 1125 Positive 1080 5 36

24Hz 1920x1080P 27 2750 Positive 74.25 1920 44 148

24 1125 Positive 1080 5 36

29.97Hz
33.72 2750 Positive 74.25 1920 44 148
1920x1080P

29.97 1125 Positive 1080 5 36

30Hz 1920x1080P 33.75 2750 Positive 74.25 1920 44 148

7
 30 1125 Positive 1080 5 36

Component timing table

SYNC PIXEL SYNC BACK
FREQ PERIOD Display
POLARITY CLOCK WIDTH PORCH
MODE LINE(kHz) LINE (pixel) LINE (pixel) LINE (pixel) LINE (pixel)
LINE
FRAME FIELD (MHz) FRAME FRAME FRAME
FIELD
(Hz) (lines) (lines) (lines) (lines)

15.734 858 Negative 13.5 712 64 62

59.94Hz 720x480i
59.94 262.5 Negative 242 3 14
15.625 864 Negative 13.5 702 64 78
50Hz 720x576i
50 312.5 Negative 287 2.5 20.5
31.47 858 Negative 27 720 63 59
59.94Hz 720x483P
59.94 525 Negative 483 6 30
31.25 864 Negative 27 720 63 69
50Hz 720x576P
50 625 Negative 576 5 39
44.96 1650 Positive 74.176 1280 40 220
59.94Hz 1280x720P
59.94 750 Positive 720 5 20
45 1650 Positive 74.25 1280 40 220
60Hz 1280x720P
60 750 Positive 720 5 20
37.5 1920 Positive 74.25 1280 40 220
50Hz 1280x720P
50 750 Positive 720 5 20
33.72 2200 Positive 74.176 1920 44 148
59.94Hz 1920X1080i
59.94 562.5 Positive 540 5 15
33.75 2200 Positive 74.25 1920 44 148
60Hz 1920X1080i
60 562.5 Positive 540 5 15
28.13 2640 Positive 74.25 1920 44 148
50Hz 1920X1080i
50 562.5 Positive 540 5 15

8
3. Component names
Product Outward
Back:

S2

Front:

9
2. Side inputs

z Remote sensor (embedded) —

Point the remote control toward this remote sensor.

z Power LED —
Power indicator light, (glows green when the TV power is On & red when TV power is Off ).

z POWER button —
Turns the TV On/Off. If the TV stops responding to the buttons on the remote control or TV
control panel and you cannot turn off the TV, press and hold the POWER button on the TV
control panel for a few seconds to reset the TV.
z ARROWS▲/▼— these buttons can be used to change the channel, adjust the volume
level or change the source you are viewing (the setting mode depends on the
SELECT).
z SELECT—Select the Channel, Volume or Source mode for the ARROWS.

z 2 HDMI IN—High-Definition Multimedia Interface input.

z USB port—Accesses JPEG or MP3 or Movie files, or updates TV firmware.
z SCART/COMPONENT VIDEO/AUDIO—High-resolution component video input and
shared composite video input, see “Connecting a Blu-ray™ / DVD player, satellite
receiver with ColorStream® or VCR”on page 24.
z ANT/CABLE—
Antenna input that supports analog (NTSC/PAL/SECAM) system
Support Digital TV system is DVB-T/C/T2 .

z PC IN—connects a personal computer.

z Digital AUDIO OUT—Digital audio outputs-SPDIF for connecting an audio amplifier.

1
3. Remote Control
The buttons used for operating the TV only are described here.

Learning about the remote control

The buttons used for operating the TV are described here.

(Sample Illustration) Remote control overview

NOTE The error message “NOT AVAILABLE” may appear if you press a
button for a function that is not available.

1
4. Service points
1
z Lead-free solder
This product uses lead-free solder (unleaded) to help protect the environment. Please read these instructions
before attempting any soldering work.

Caution: Always wear safety glasses to prevent fumes or molten solder from getting into
the eyes. Lead-free solder can splatter at high temperatures (600 ).

„ Lead-free solder indicator

Printed circuit boards using lead-free solder are engraved with an "F."

„ Properties of lead-free solder

The melting point of lead-free solder is 40-50 higher than leaded solder.

„ Servicing solder
Solder with an alloy composition of Sn-3.0Ag-0.5Cu or Sn-0.7Cu is recommended. Although servicing with
leaded solder is possible, there are a few precautions that have to be taken. (Not taking these precautions may
cause the solder to not harden properly, and lead to consequent malfunctions.)

Precautions when using leaded solder

z Remove all lead-free solder from soldered joints when replacing components.
z If leaded solder should be added to existing lead free joints, mix in the leaded solder thoroughly after the
lead-free solder has been completely melted (do not apply the soldering iron without solder).

„ Servicing soldering iron

A soldering iron with a temperature setting capability (temperature control function) is recommended.
The melting point of lead-free solder is higher than leaded solder. Use a soldering iron that maintains a high
stable temperature (large heat capacity), and that allows temperature adjustment according to the part being
serviced, to avoid poor servicing performance.

Recommended soldering iron:

z Soldering iron with temperature control function (temperature range: 320-450 )

Recommended temperature range per part:

Part Soldering iron temperature
Mounting (chips) on mounted PCB 320ºC±30ºC
Mounting (chips) on empty PCB 380ºC±30ºC
Chassis, metallic shield, etc. 420ºC±30ºC

The PWB assembly which has used lead free

(1) IR PWB, KEY PWB, SIDE I/O PWB, T PWB
(2) FORMATTER PWB
(3) POWER BOARD

1
5. Adjustment
5-1 Entering into factory Mode:
Press ◄ key, next press EXIT key, last press ENTER key in remote control to enter into
factory mode.

5-2 Syetem Information

Please check below red color area:
50L2556: Toshiba model name
Model name list :
SRO40D (40L2546/40L2556)
SRO50D (50L2546/50L2556)

SRO40D : COMPAL Model name

00.16.20 : F/W version.
Feb 6 2015 ,10:10:39:F/W release time.
PQ FW: Picture Qunaty FW version
AQ FW: Audio FW version.

1
5-3 Color Temperature Adjustment

(1) Set the signal generator to RGB, 1024*768, 60HZ(ASTRO-859: PG1 856), Level:178 (70%).

Full white pattern.

(2) Press up or down key of remote control to select “Cool”, Press ENTER key to enter the item.
R, G, B drive values are set for COOL, Medium, and WARM independently.
Color Cool Medium Warm
x 0.262 0.2840 0.313
y 0.262 0.297 0.329
Adjust
±0.003 ±0.003 ±0.003
Tolerance

(3) Select Cool

(1) Cool spec.:

: x = 0.262 y = 0.262

(2) If the x and y value are larger than specification,

Decrease Red drive from default value.
Increase Blue drive from default value.

(3) If the x or y or both x and y value is/are smaller than specification.

Increase Red drive from default value
Decrease Blue drive from default value

(4) According to a x and y value, please following adjustment of (4-1) or (4-2).

(4-1) If x value is higher than spec
Decrase Red drive from default value.
(4-2) If y value is higher than spec,
Increase Blue drive from default value

(4) Select [Medium]

Medium spec.:
: x = 0.2840 y = 0.297
Adjust R drive (RED) or B drive (BLUE) to set x and y above.

(5) Select [WARM]

WARM spec.:
: x = 0.313 y = 0.329
Adjust R drive (RED) or B drive (BLUE) to set x and y above.

(6) Exit Factory Mode:

After finish adjusting color temperature,press [EXIT] to exit factory mode.

1
5.4 Source Calibration ADC Adjustment

INPUT Input signal

No SOURCE Process /Instructions Remark
1 INPUT 2 Component [Process] 100% Full field COLOR Bar signal
SD 576i 1. Make TV to be in ‘M’.
2. Connect 100% Full field COLOR Bar signal
(576i) to ‘Source 2 Input’. 51AE0BF4
3. Change Video Input to ‘Source 2 Input’.
4. Start Auto adjustment by ’ 51AE14EB’
remote code sending.

[OSD INDICATION]
During Adjustment ; ‘A/D ADJUSTING’
After Finish adjusting ;
‘OK’
--> Adjustment succeeds.
‘NG’
--> Adjustment fails.

2 INPUT 2 Component [Process] 100% Full field COLOR Bar signal

HD 1. Make TV to be in ‘M’.
1080i/50hz 2. Connect 100% Full field COLOR Bar signal
HD 1080i/50hz to‘Source 2 Input. 51AE0BF4
3. Start Auto adjustment by ’ 51AE14EB’
remote code sending.

[OSD INDICATION]
During Adjustment ; ‘A/D ADJUSTING’
After Finish adjusting ;
‘OK’
--> Adjustment succeeds.
‘NG’
--> Adjustment fails

3 PC 1024*768/60hz [Process] White pattern and 16 Gray pattern

1. Make TV to be in ‘M’.
2. Connect White Pattern signal
to ‘PC Input’.
And change 16 Gray signal to ‘PC Input’.

3. Change Video Input to PC input.

51AE11EE

4. Start Auto adjustment by ’ 51AE14EB’

remote
code sending.

[OSD INDICATION]
During Adjustment ; ‘A/D ADJUSTING’
After Finish adjusting ;
‘OK’
--> Adjustment succeeds.
‘NG’
--> Adjustment fails.

1
 INPUT Input signal
No SOURCE Process /Instructions Remark
4 INPUT 1 RGB 576i/ [Process] Checker pattern
50Hz (PAL) 1. Make TV to be in ‘M’.
2. Connect checker pattern
to ‘scart Input’. 51AE12ED
3. Change Video Input to scart input.
4. Start Auto adjustment by ’ 51AE14EB’
remote
code sending.

[OSD INDICATION]
During Adjustment ; ‘A/D ADJUSTING’
After Finish adjusting ;
‘OK’
--> Adjustment succeeds.
‘NG’
--> Adjustment fails.

Please press Right+ Exit+OK Key to Engineer mode

Check ADC all status is Pass .

5-5 Prset Channel

Select OSD as factory locate.
This Function will auto setup preset channel in TV set.

5-6 NVRAM CLEAR

Clean all PCBA data include color temperature/ Source calibration/ preset channel.
Please don’t use this mode for factory side.

5-7 Timer Clear

Reset the timer which records hours of LCD panel burn in.

5-8 Reset to Default

Reset all settings of OSD menu to default value.

1
5-9 F/W USB upgrade
This spec description how to burn in the FW from USB by model name
1. From UI upgrade
If TV set no this model name mechanism in FW.
First time should be used MasterUpgrade.bin do the FW upgrade.

2. From UI upgrade
If TV set has already this model name mechanism in FW.
ex: If the model name check not same TV model name will reject this upgrade.

3. From out side Input keypad upgrade.

If don't care the model name mechanism whether exist .
- change the .bin file of model name to MstarUpgrade.bin
- press /hold Input keypad in TV side then AC on util green light flash to release Input key.
ex:

1. USB storage device support FAT32 format only.

2. Please check the file name which you want to upgrade corresponds with the format below,
For DVB-T model :
40L2546.bin and 50L2546.bin
For DVB-T2 model:
1
 40L2556.bin and 50L2556.bin

Save the upgrade file as X0L25Y6.bin, under the USB drive's root directory. X=4 or 5,Y=4 or 5.
3. Insert your USB storage device to the USB slot of the TV set.

4. You have 2 kind format to do F/W USB upgrade.

Case1:Direct upgrade F/W no use panel
Step1:PCBA connect IR/LED board ,Power supply unit and insert USB in port.

Step2: Press side Key “Input” (S4 loacate) and AC Power ON.
Step 3:Waiting LED flash than can put off S4 key .TV will auto ruuning F/W upgrade.
Step 4:During FW Upgrade , Green color LED will Flashing continuous.

Step 5:
When FW Upgrade complete:
Green color LED will auto turn off about 12~15 sec than auto turn on.

Step 6: Change next PCBA and follow Step 2~5.

Case2: Follow below Step by step operator OSD:

Step 1: Insert USB Than TV will show
“USB Devise was connected to TV.Do you want to open Media Plaer?”
Please change icon from Yes to No.

1
 Step 2: Press remote control “Menu ”key and select “Installation” page
Control remote down key to find Software Update (USB) icon and Press “OK” key.

Step 3: Screan will show message “Do you want to upgrade software?”
Please Press “Left Key” and start to upgrade.

Step 4:
TV will show “SOFTWARE UPGRADE COMPLETE” message on screen.

Step 5: TV is restarted when the update process finished.

Step 6: After restarted, press "◄" and "EXIT" then "OK" key. Entry to Factory Mode.
Confirm Model ID / FW version /Mboot version and date.

Step 7: To Check New FW version

Press "MENU" key then using ◄ or ► key until “Setup” page shows on the screen.
Press "▲ or ▼" key unitl you find "System Information" with focused blue bar.
2
Step 8:To show the imformation, click "OK"

2
6. Troubleshooting
The flow chart shown below will help you to troubleshoot your Televison set with it doesn’t display normally.
Each procedure offers a simple way to check for system errors. Before starting, ensure that there is a signal in
and that the Televison is turned on.

IR/LED board NO light

NG
Check CN14
Inspect Assy Cable wire
Pin2 :3.3V-ST
conect

OK

NG
Check CN14
Change Main board
pin4,5 >2.5V

OK

NG
Check IR/LED
Change new IR/LED board
board Assy

2
Have a video but no sound

NG
Check M/B wire
Re-plug in
connect CN7 plug

OK

NG Re-plug wire/
Check Speaker
Change new Speaker
Connect Assy

OK

NG
Change new Power board
Check M/B CN 9,
40”: PK101W0810I
pin 6=12.5V
50”:PK101W0800I/PK101W0820I

OK

Change new main board

2
Have a Audio but no Video

NG
Check Backlight
Check Wire assy
CN9 Pin 13 need

OK

NG Check LVDS Wire

Check M/B CN8
assy/change new LVDS
LVDS connect
wire

OK

NG
Change new Power board
Check M/B U13/
40”: PK101W0810I
FB17=12~12.5V
50”:PK101W0800I/PK101W0820

OK

Change new main board

Change LCD Module