Installation Manual

Release 8.2 - May 2012

Downloaded from www.Manualslib.com manuals search engine

 Legal notice:

Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of

Alcatel-Lucent. All other trademarks are the property of their respective
owners.

The information presented is subject to change without notice.

Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.

Copyright © 2012 Alcatel-Lucent. All rights reserved.

The CE mark indicates that this product conforms to the following Council
Directives:
- 2004/108/EC (concerning electro-magnetic compatibility)
- 2006/95/EC (concerning electrical safety)
- 1999/5/EC (R&TTE)

Downloaded from www.Manualslib.com manuals search engine

 
      

Chapter 1
General Presentation

 Preliminary ............................................................................................... 1.1

 Overview ........................................................................................................ 1.1
 Security ...................................................................................................... 1.1
 Safety rules .................................................................................................... 1.1
 Protection against Interferences ...................................................... 1.4
 Protection against Interferences .................................................................... 1.4

Chapter 2
Hardware: Platform and Interfaces

 Overview .................................................................................................... 2.1

 Platforms ................................................................................................... 2.1
 OmniPCX Office RCE Compact .................................................................... 2.1
 OmniPCX Office RCE Small .......................................................................... 2.3
 OmniPCX Office RCE Medium ...................................................................... 2.4
 OmniPCX Office RCE Large ......................................................................... 2.4
 Installation ................................................................................................ 2.5
 Overview ........................................................................................................ 2.5
 Equipment ................................................................................................. 2.6
 Boards and Options ....................................................................................... 2.6

              0-1

Downloaded from www.Manualslib.com manuals search engine

     

 Detailed description ....................................................................................... 2.7

Chapter 3
System Services

 Software Licence Management ......................................................... 3.1

 SOFTWARE LICENCE MANAGEMENT ....................................................... 3.1
 Software Keys ......................................................................................... 3.1
 Voice Services Available in "Limited" Mode .................................................. 3.2
 Software Key Change .................................................................................... 3.3
 Detailed description .............................................................................. 3.3
 Services controlled by the "Main" software key ............................................. 3.4
 Services controlled by the “CTI” software key ............................................... 3.7
 Descriptions ............................................................................................. 3.9
 Introduction .................................................................................................... 3.9
 Standard telephony ....................................................................................... 3.9
 Alcatel Reflexes sets ..................................................................................... 3.9
 Analog interfaces ..........................................................................................3.10
 Mobility .........................................................................................................3.10
 Call handling features ...................................................................................3.10
 Networking ....................................................................................................3.11
 Internet access (relevant up to R7.1) ...........................................................3.11
 Web applications ..........................................................................................3.11
 SNMP ...........................................................................................................3.12
 RAS (relevant up to R7.1) ............................................................................3.12
 Lan telephony ...............................................................................................3.12
 VoIP Gateway ...............................................................................................3.12
 Supplementary information ...........................................................................3.13
 Music on Hold (MOH) ...................................................................................3.14
 Metering ........................................................................................................3.14
 Languages ....................................................................................................3.14
 Pay Per User (PPU) .....................................................................................3.14
 ACD ..............................................................................................................3.15

0-2              

Downloaded from www.Manualslib.com manuals search engine

     

 Managed services ........................................................................................3.15

 Mobility on GSM ...........................................................................................3.15

Chapter 4
Installation and Cabling

 Presentation ............................................................................................. 4.1

 Location of Unit .............................................................................................. 4.1
 Environment .................................................................................................. 4.3
 Connections and Cabling .................................................................... 4.3
 Detailed description ....................................................................................... 4.3
 Power Supply .......................................................................................... 4.19
 Installation procedure ...................................................................................4.19
 SIP Terminals .......................................................................................... 4.34
 8082 My IC Phone ........................................................................................4.34
 4135 IP Conference Phone ..........................................................................4.40
 Generic SIP Phones .....................................................................................4.46
 8 Series Sets ........................................................................................... 4.48
  IP Touch 4008/4018 Phone ..........................................................................4.48
  IP Touch 4028/4038/4068 Phone .................................................................4.53
 9 Series Sets ........................................................................................... 4.60
  4019 Digital Phone .......................................................................................4.60
  4029/4039 Digital Phone ..............................................................................4.62
 V24/CTI Interface Module ................................................................... 4.65
  Hardware description ....................................................................................4.66
  Hardware configuration ................................................................................4.67
  External connections ....................................................................................4.68
 AP Interface Module ............................................................................. 4.70
  Hardware description ....................................................................................4.70
  Hardware configuration ................................................................................4.72
  External connections ....................................................................................4.73
 S0 Interface Module .............................................................................. 4.75
  Hardware description ....................................................................................4.75

              0-3

Downloaded from www.Manualslib.com manuals search engine

     

  Hardware configuration ................................................................................4.77

  External connections ....................................................................................4.78
 Intelligent Base Stations ..................................................................... 4.81
 Detailed description ......................................................................................4.81
 Safety rules ...................................................................................................4.89
 PIMphony ................................................................................................. 4.92
 Overview .......................................................................................................4.92
 Additional Information ...................................................................................4.93
 Reflexes Terminals ............................................................................... 4.94
 Installation procedure ...................................................................................4.94
 Extending Your Installation ............................................................... 4.99
 Detailed description ......................................................................................4.99

Chapter 5
Stations Default Configuration

 Detailed description .............................................................................. 5.1

 DEFAULT CONFIGURATION ....................................................................... 5.1

Chapter 6
Start-Up

 System Startup from a Phone Set .................................................... 6.1

 Configuration procedure ................................................................................ 6.1
 System Startup from OMC .................................................................. 6.9
 Overview ........................................................................................................ 6.9
 Installation procedure .................................................................................... 6.9
 Accessing the System ..................................................................................6.10
 Downloading the Software ............................................................................6.17
 Services provided .........................................................................................6.19

0-4              

Downloaded from www.Manualslib.com manuals search engine

     

Chapter 7
Maintenance Services

 Maintenance Level 1 .............................................................................. 7.1

 Maintenance .................................................................................................. 7.1

Chapter 8
Glossary

 Glossary .................................................................................................... 8.1

 A .................................................................................................................... 8.1
 B .................................................................................................................... 8.1
 C .................................................................................................................... 8.2
 D .................................................................................................................... 8.3
 E .................................................................................................................... 8.3
 F .................................................................................................................... 8.3
 G .................................................................................................................... 8.4
 H .................................................................................................................... 8.4
 I ...................................................................................................................... 8.4
 K .................................................................................................................... 8.5
 L ..................................................................................................................... 8.5
 M .................................................................................................................... 8.5
 N .................................................................................................................... 8.6
 O .................................................................................................................... 8.6
 P .................................................................................................................... 8.6
 Q .................................................................................................................... 8.7
 R .................................................................................................................... 8.7
 S .................................................................................................................... 8.8
 T .................................................................................................................... 8.8

              0-5

Downloaded from www.Manualslib.com manuals search engine

     

 U .................................................................................................................... 8.9

 V .................................................................................................................... 8.9
 W ................................................................................................................... 8.9

0-6              

Downloaded from www.Manualslib.com manuals search engine

   

     

1.1 Preliminary

1.1.1 Overview
1.1.1.1 SYMBOLS USED IN THE DOCUMENTATION
See note.

See important information.

1.1.1.2 CLAUSES
Copyright and Trademarks
Datalight is a registered trademark of Datalight,Inc.
FlashFXtm is a trademark of Datalight, Inc.
Copyright 1993 - 2000 Datalight, Inc., All Rights Reserved.

1.2 Security

1.2.1 Safety rules

1.2.1.1 Safety Declaration
We, Alcatel-Lucent Enterprise 32, avenue Kléber 92707 Colombes Cedex - France, declare
that the products presented in this manual conform to the essential requirements of Directive
1999/CE/5 of the European Parliament and Council.
Any unauthorized modification to the products invalidates this declaration of conformance.
In pursuance of this directive which appeared in the Official Journal of the European
Community on April 7 1999, this equipment can be used in all European Community member
states, and in Switzerland and Norway.

Copyright 2001 - 2000 Datalight, Inc., All Rights Reserved. In order to better serve its
customers, Alcatel-Lucent Enterprise reserves the right to modify the characteristics of its
products without notice.
Alcatel-Lucent Enterprise - 32, avenue Kléber F-92707 Colombes Cedex RCS Paris 602 033
185.
1.2.1.2 General Recommendations

              1-1

Downloaded from www.Manualslib.com manuals search engine

 Chapter 1   

Protective earthing
This equipment must imperatively be connected to a permanent earth protection

installed according to current legislation.

Installation of the mains power
The mains power must be installed as close as possible to the unit and must be easily
accessible. The power supply lead is used as the master switch.
Free board slots
It is essential that empty board slots are guarded with the appropriate expansion

slot covers for full electromagnetic shielding, the safety of people working nearby (in
the presence of hazardous voltages) and the prevention of fire propagation (from inside
the unit).
Lead and Lithium batteries
There is a risk of explosion if the batteries are incorrectly replaced. Only use

batteries of identical type, or manufacturer recommended equivalents. Discard used

batteries according to the battery manufacturer's instructions.
Power supply
Due to the presence of hazardous voltages, the rear metal panel can only be

removed by qualified personnel.

If it is necessary to carry out work on a power supply unit, first disconnect the mains cable from
the system as well as any external EPS48 power connections that may be connected. Then
remove the rear metal panel of the power supply block and disconnect the batteries.
High leakage current
A permanent earth connection is essential before making TRT/TNV-3

telecommunication network connections.

In the case of a poor earth connection, it is MANDATORY to disconnect the
telecommunications accesses before reconnecting the equipment to earth. It is then necessary
to verify that all the connections have been made correctly.
Before removing any board that provides access to a telecommunications

network of class TRT/TNV-3, make sure you disconnect the links. Reconnect the links
once the board is re-inserted.
Installation of DECT bases
For further information on recommendations relating to the exposure of the public to the
electromagnetic field, refer to "Installation of DECT bases".
1.2.1.3 Declaration of Conformance With Directives
This equipment is designed to be connected to the public telephone network using the
appropriate interfaces.

1-2              

Downloaded from www.Manualslib.com manuals search engine

   

The EC labeling indicates that this product conforms to the EC directives currently in force, in
particular:
- 89/336/EEC (Electromagnetic compatibility)
- 73/23/EEC (Low Voltage)
- R&TTE 1999/5/EC compliance
- 1999/519/EC (Specific Absorption Rate)
1.2.1.4 Interface Classification
1.2.1.4.1 OmniPCX Office RCE Small, Medium, Large
SELV: Safety Extra Low Voltage TNV-3: Telecommunication Network Voltage

Figure 1.2: OmniPCX Office RCE Small, Medium, Large

1.2.1.4.2 OmniPCX Office RCE Compact

              1-3

Downloaded from www.Manualslib.com manuals search engine

 Chapter 1   

Figure 1.3: OmniPCX Office RCE Compact

Note:
The Mini-MIX daughter board requires BACKXS-N back panel and PSXS-N power supply module. The
Mini-MIX daughter board can be used only in an OmniPCX Office RCE Compact or, in case of migration
from R7.1 or lower, in a Compact Edition 2nd Generation, equipped with a PowerCPU board.

1.3 Protection against Interferences

1.3.1 Protection against Interferences

Notice to the attention of the users and installer:
USA - FCC (Federal Communication Commission)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to consult the installer or service person.
Changes or modifications to this equipment, not expressly approved by ALCATEL-LUCENT,

1-4              

Downloaded from www.Manualslib.com manuals search engine

   

may cause harmful interference and void the user’s authority to operate this equipment.
Japan - VCCI (Voluntary Control Council for Interference)

Translation :
This is a Class B product based on the standard of the Voluntary Control Council for
Interference from Information Technology Equipment (VCCI). If this is used near a radio or
television receiver in a domestic environment, it may cause radio interference. Install and use
the equipment according to the instruction manual.

              1-5

Downloaded from www.Manualslib.com manuals search engine

 Chapter 1   

1-6              

Downloaded from www.Manualslib.com manuals search engine

   

    

 
2.1 Overview
Alcatel-Lucent OmniPCX Office Communication Server is a business communication server
offering proven telephony functions with data management. This "multi-purpose" server
provides a turnkey global communication solution for small and medium-scale businesses with
6 to 200 employees.
The Alcatel-Lucent OmniPCX Office Communication Server range includes:
- the Alcatel-Lucent OmniPCX Office Rich Communication Edition Compact platform
- the Alcatel-Lucent OmniPCX Office Rich Communication Edition Small platform
- the Alcatel-Lucent OmniPCX Office Rich Communication Edition Medium platform
- the Alcatel-Lucent OmniPCX Office Rich Communication Edition Large platform
The Alcatel-Lucent OmniPCX Office Communication Server range is supplied:
- with all the sub-assemblies required for your particular configuration,
- configured with the software key corresponding to the level of services desired (according
to country).
The stations are packaged separately.

2.2 Platforms
Alcatel-Lucent OmniPCX Office Communication Server is available in the following models:

2.2.1 OmniPCX Office RCE Compact

- 14 ports.
- 1 CPU slot + 1 MIX slot

              2-1

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2  !  " #  "$

- Energy consumption: 1.5 A (240 V)

- Dimension: H = 345 mm; W = 370 mm; D = 65 mm.
- Weight: 5.1 kg.
The following mixed boards are available:
- MIX 2/4/4
- MIX 2/4/8
- MIX 2/8/4
- MIX 4/4/8
- MIX 4/8/4
- AMIX-1 4/4/4
- AMIX-1 4/4/8
- AMIX-1 4/8/4
- Mini-MIX (PowerCPU daughter board)
Note:
This wall-mounted version is also called XS-N.
The Mini-MIX daughter board, plugged on a PowerCPU booard, requires an OmniPCX Office
RCE Compact, or, in case of migration from Release 7.1 or lower, a Compact Edition 2nd
Generation. The Mini-MIX daughter board cannot be used on an Alcatel-Lucent OmniPCX
Office Compact Edition.
The PowerCPU board shows a Mini-MIX LED activated when the Mini-MIX daughter board is
detected on the PowerCPU board.

2-2              

Downloaded from www.Manualslib.com manuals search engine

  !  " #  "$

Figure 2.2: Mini-MIX connections on PowerCPU Board

Equipment numbering:
- Slot 80 EN 01 for the first T0 access (80-001-01)
- Slot 80 EN 02 for the second T0 access (80-002-01)
- Slot 80 EN 09 for the first Z access (80-009-01)
- Slot 80 EN 10 for the second Z access (80-010-01)

2.2.2 OmniPCX Office RCE Small

              2-3

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2  !  " #  "$

- 28 ports.
- 1 CPU slot 2 general-purpose slots (no SLI16 board).
- Energy consumption: 1 A (230 V) / 2 A (110 V) - 80 W.
- Dimension: H = 66 mm; W = 442 mm; D = 400 mm.
- Weight: 6 kg.

2.2.3 OmniPCX Office RCE Medium

- 56 ports.
- 1 CPU slot 5 general-purpose slots.
- Energy consumption: 1,2 A (230 V) / 2,3 A (110 V) - 120 W.
- Dimension: H = 110 mm; W = 442 mm; D = 400 mm.
- Weight: 11 kg.

2.2.4 OmniPCX Office RCE Large

- 96 ports.
- 1 CPU slot + 4 general-purpose slots + 4 specific slots (no UAI16 and MIX boards)
- Energy consumption: 1,2 A (230 V) / 2,3 A (110 V) - 150 W.
- Dimension: H = 154 mm; W = 442 mm; D = 400 mm.
- Weight: 13 kg.

2-4              

Downloaded from www.Manualslib.com manuals search engine

  !  " #  "$

2.3 Installation

2.3.1 Overview
___change-begin___
___change-end___
This hardware must be installed on the customer's site, by a qualified installer, in

              2-5

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2  !  " #  "$

compliance with the instructions provided with the hardware.

Equipment shall be installed at the factory or in the field by submitter's trained personnel

in accordance with the installation instruction provided with the equipment.

2.4 Equipment

2.4.1 Boards and Options

The following table lists the boards available on OmniPCX Office RCE Small, Medium, Large.
Board Function Optional boards Connections
APA2 2, 4 or 8 analog trunk line GSCLI: Ground Start Analog trunk line (TL),
APA4 interfaces signaling TL-PS diversion
APA8 CLIDSP: CLIP local
management
ATA2 2 or 4 analog trunk line MET: pulse meter Analog trunk line (TL),
ATA4 interfaces receivers (phased out) TL-PS diversion
BRA2 2, 4 or 8 T0 basic accesses ISDN network
BRA4 ISDN-EFM T0/S0
BRA8 forwarding box
PowerCPU Processing Unit (As of R8.0), HSL1, HSL2: Lanswitch or Ethernet
SD/MMC Memory card (2GB), interconnection with terminal
256 MB DDR2 SDRAM. expansion modules Please-wait message player
Optional Hard Drive AFU-1: (Auxiliary Tuner for background music
Function Unit) Alarm
ARMADA VoIP32: VoIP Doorphone
channels Loudspeaker
General call ringer
ISDN-EFM T0/S0
forwarding box
Pulse metering device
OMC
DDI2 2 or 4 analog trunk line Analog trunk line with
DDI4 interfaces with Multiple Multiple Subscriber
Subscriber Numbers (MSN) Numbers (MSN)
LanX8 8 or 16 port Ethernet 10/100 BT @ Phones, Hub, Lanswitch,
LanX16 (of which 1 or 2 10/100/1000 BT PC, etc.
LANX16-1 ports on LANX-2 boards)
LanX8-2
LANX16-2
PowerMEX Extension module controller
(equipped with
an HSL1 board)

2-6              

Downloaded from www.Manualslib.com manuals search engine

  !  " #  "$

Board Function Optional boards Connections

MIX244 0, 2 or 4 T0 basic accesses + 4 ISDN network, analog Z
MIX248 or 8 UA interfaces + 4 or 8 Z terminals and Alcatel-Lucent
MIX284 interfaces 9 series or Alcatel Reflexes
MIX484 stations
MIX448
MIX044
MIX084
MIX048
AMIX484-1 4 analog line accesses, 4 or 8 GSCLI: Ground Start PSTN network, analog Z
AMIX448–1 UA interfaces and 4 or 8 Z signaling terminals and Alcatel-Lucent
AMIX444–1 interfaces CLIDSP: local CLIP 9 series or Alcatel Reflexes
management stations
METCLI
PRA-T2 PRA -T2, DASS2, DLT2: 30 x PRA-T2: ISDN network
PRA-T1 64-Kpbs B-channels + 1 x DASS2: UK public/private
DASS2 64-Kbps D-channel; 2048 Kbps. network
DLT2 PRA-T1: 23 x 64-Kbps DLT2: Private QSIG
T1-CAS B-channels + 1 x 64-Kbps network
T1-CSS D-channel; 1544 Kbps PRA-T1: Hong-Kong ISDN
PCM R2 23 x 64-Kbps B-channels + 1 x network
64-Kbps D-channel ISDN (US) T1-CAS: USA
T1-CAS: 24 x B-channels, public network
including signaling; 1544 Kbps. PCM R2: Public network
PCM R2: 30 x 64 Kbps
B-channels +1 x 4 Kbps
signaling channel; 2048 Kbps.
SLI4 4, 8 or 16 Z interfaces Analog Z terminals
SLI8
SLI16
SLI4-1
SLI8-1
SLI16-1
SLI4-2
SLI8-2
SLI16-2
UAI4 4, 8 or 16 UA interfaces Alcatel-Lucent 9 series or
UAI8 UAI16-1 board: possibility of Alcatel Reflexes stations
UAI16 powering terminals connected to Multi Reflexes 4099
UAI16-1 the 16 interfaces remotely from 4070 IO/EO DECT base
an external EPS48 power supply stations
EPS48 only on interface 1
of the UAI16-1 board

2.4.2 Detailed description

2.4.2.1 Processing Unit PowerCPU Board

              2-7

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2  !  " #  "$

As of R8.0, the PowerCPU board performs the CPU functions of an OmniPCX Office system.
2.4.2.1.1 Function of the LEDs

Name Color Function

CPU Green CPU functioning LED (flashing)
POWER Red/Green - Mains operation: steady green LED
- Battery operation: steady yellow LED
- Idle: flashing red LED
- System shut down: steady red LED
FAN Red/Green - Both fans functioning: steady green LED
- 1 or both fans down: steady red LED
LAN Green LAN functioning LED (flashes when there is traffic)
Mini-MIX Green (only on Green only when accepted by the license 2B channels for MIX
OmniPCX Office RCE boards. Detection of Mini-MIX board in OmniPCX Office RCE
Compact platform) Compact platform.
MODULE Green Presence of HSL board

2.4.2.2 SLI-X Boards

Board allowing the connection of 4, 8 or 16 analog terminals.

2.4.2.3 UAI-X Boards

2-8              

Downloaded from www.Manualslib.com manuals search engine

  !  " #  "$

Board used for connecting up digital terminals or DECT 4070 IO/EO base stations.

The UAI16-1 board is used to power terminals connected to the 16 interfaces remotely from an
EPS48 external power supply connected to interface 1 via an external adapter cable (splitter).
Caution:
Only use EPS48 power supplies and the splitters provided.

2.4.2.4 MIX x/y/z

These boards are used to connect 2 or 4 base T0 access points, 4 or 8 analog terminals and 4
or 8 digital dedicated terminals.

2.4.2.5 AMIX-1 X/Y/Z Boards

These boards are used to connect 4 analog accesses, 4 or 8 analog terminals and 4 or 8
digital dedicated terminals.

              2-9

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2  !  " #  "$

2.4.2.6 BRA-X Board

These boards are used to connect 2, 4 or 8 base T0 access points (2 B channels + 1 D
channel) in order to connect the system to the digital public ISDN network (T0 point-to-point or
multipoint connection) or to a private network (DLT0 point-to-point connection); the operating
mode, T0 or DLT0, can be configured by OMC.

2.4.2.7 PRA Boards

This board provides 1 primary access for connecting the Alcatel-Lucent OmniPCX Office
Communication Server system to the ISDN digital public network or to private networks:
- PRA -T2, DASS2, DLT2 : 30 x 64-Kbps B-channels + 1 x 64-Kbps D-channel; 2048 Kbps.
- PRA-T1 : 23 x 64-Kbps B-channels + 1 x 64-Kbps D-channel; 1544 Kbps.
- T1-CAS: 24 x B-channels, including signalling; 1544 Kbps.
- PCM R2: 30 x 64-Kbps B-channels + 1 x 4-Kbps signaling channel; 2048 Kbps.
The diagram below shows the end-plate of the PRA-T2 board, but the other PRA boards are
similar.

2.4.2.7.1 Function of the LEDs

2-10              

Downloaded from www.Manualslib.com manuals search engine

  !  " #  "$

T2 Name T1 Name Function

BUSY BUSY B-channels busy (red LED lights up if at least 1 B-channel is busy)
RAI (ATD) RAI Remote frame alarm (red LED lights up on alarm)
AIS (SIA2M) AIS Too many "1's in the 2-Mbit binary train (red LED lights up on alarm)
NOS (MS) NSIG Absence of 2-Mbit signal (red LED lights up on alarm)
CRC (TE) CRC CRC error (red LED lights up on alarm)
LOS (PVT) NSYN Loss of frame alignment (red LED lights up on alarm)

2.4.2.8 APA Boards

This board is used to connect to the analog public network (2, 4 or 8 LR).

The APA board does not support pulse dialing in Australia and New Zealand.

2.4.2.9 LAN-X Boards

These boards are used to create a local area network (LAN) by connecting client PCs,
IP-Phones, an external Lanswitch and servers.

              2-11

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2  !  " #  "$

Each category-5 RJ45 connector has 2 green LEDs:

- Left LED = link status and activity:
• off: link disconnected
• on: link connected
• blinking: link active
- Right LED = full duplex/collision:
• off: Half Duplex
• on: Full Duplex
• blinking: collision
2.4.2.10 LANX-2 Boards
The LanX8-2 and LanX16-2 are second generation boards integrating respectively 1 or 2
Ethernet Gigabit ports for a Lanswitch/Layer 2 configuration. Any port can be used as an
Uplink, as all the ports are auto MDI/MDIX.
Unlike the 1st generation boards, the LEDs of the A and B ports are both located at the top of
the board. The Led display is as follows:
- Green LED (left) = link status and activity:
• off: link disconnected
• on: link connected
• blinking: link active
- yellow LED (right) = speed:
• off: low speed (10 or 100 Mb for Gigabit port, 10 Mb for the other ports)
• on: high speed (1 Gb for Gigabit port, 100 Mb for the other ports)

2-12              

Downloaded from www.Manualslib.com manuals search engine

  !  " #  "$

2.4.2.11 DDI-X Board

This board is used to connect 2 or 4 analog trunk lines with Multiple Subscriber Numbers.

2.4.2.12 ATA Board

The ATA (Analog Trunk Access) board serves to connect analog trunk lines (2 or 4 TL).

The ATA board does not support pulse dialing in Australia and New Zealand.

2.4.2.13 Daughter Board Provision on PowerCPU Board

The table below presents the daughter boards which can be provided on the PowerCPU
board, according to the platform used.
Daughter Boards OmniPCX Office RCE Compact OmniPCX Office RCE Small,
Medium, Large
ARMADA VoIP32 Yes Yes
HSL1 No Yes
HSL2 No Yes
AFU-1 Yes Yes
SATA HARD DISK + Yes Yes
SATAEXT board
Mini-Mix Yes No

Note:
The Mini-MIX daughter board requires BACKXS-N back panel and PSXS-N power supply module. The

              2-13

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2  !  " #  "$

Mini-MIX daughter board can be used only in an OmniPCX Office RCE Compact or, in case of migration
from R7.1 or lower, in a Compact Edition 2nd Generation, equipped with a PowerCPU board.

Figure 2.22: Example of Daughter Boards on PowerCPU

2.4.2.14 Provision By Platform

2.4.2.14.1 OmniPCX Office RCE Compact

Board MIX Slot CPU Slot

PowerCPU No Mandatory
MIX x/y/z Yes No
AMIX-1 x/y/z Yes No

2.4.2.14.2 OmniPCX Office RCE Small

2-14              

Downloaded from www.Manualslib.com manuals search engine

  !  " #  "$

Boards Slots 1-2 CPU Slot

PowerCPU No Mandatory
MIX x/y/z Yes No
AMIX-1 x/y/z Yes No
UAI4, UAI8, UAI16, UAI16-1 Yes No
SLI4, SLI8, SLI4-1, SLI8-1, SLI4-2, SLI8-2 Yes No
SLI16, SLI16-1, SLI16-2 No No
PRA-T2, PRA-T1, DASS2, DLT2, T1-CAS, Yes No
PCM R2
APA4, APA8 Yes No
DDI2, DD14 No No
BRA2, BRA4, BRA8 Yes No
LANX8, LANX16, LANX16-1, LANX8-2, Yes No
LANX16-2

2.4.2.14.3 OmniPCX Office RCE Medium

Boards Slots 1-2-3-4-5 CPU Slot

PowerCPU No Mandatory
MIX x/y/z Yes No
AMIX-1 x/y/z Yes No
UAI4, UAI8, UAI16, UAI16-1 Yes No
SLI4, SLI8, SLI16, SLI4-1, SLI8-1, SLI16-1, Yes No
SLI4-2, SLI8-2, SLI16-2
PRA-T2, PRA-T1, DASS2, DLT2, T1-CAS, PCM Yes No
R2
APA4, APA8 Yes No
DDI2, DD14 Yes No
BRA2, BRA4, BRA8 Yes No
LANX8, LANX16, LANX16-1, LANX8-2, LANX16-2 Yes No

              2-15

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2  !  " #  "$

2.4.2.14.4 OmniPCX Office RCE Large

Boards Slot 1 Slots 2-3-4 Slots5-6-7-8 CPU Slot

PowerCPU No No No Mandatory
MIX x/y/z Yes Yes No No
AMIX-1 x/y/z Yes Yes No No
UAI4, UAI8 Yes Yes Yes No
UAI16, UAI16-1 Yes Yes No No
SLI4, SLI8, SLI16, SLI4-1, Yes Yes Yes No
SLI8-1, SLI16-1, SLI4-2, SLI8-2,
SLI16-2
PRA-T2, PRA-T1, DASS2, DLT2, Yes Yes Yes No
T1-CAS, PCM R2
APA4 Yes Yes Yes No
APA8 Yes No Yes No
DDI2, DD14 Yes Yes Yes No
BRA2, BRA4, BRA8 Yes Yes Yes No
LANX8, LANX16, LANX16-1, Yes Yes Yes No
LANX8-2, LANX16-2

2-16              

Downloaded from www.Manualslib.com manuals search engine

   

    

3.1 Software Licence Management

3.1.1 SOFTWARE LICENCE MANAGEMENT

On an Alcatel-Lucent OmniPCX Office Communication Server several types of devices may be
connected, several services may be offered and several applications may run.
The purpose of the feature “Software Licence Management” is to define for a given system
(i.e. customer) the service level to offer, this mainly means:
- What devices are allowed and how many of each type.
- Which service is offered.
- Which application is to open.
- How many users are allowed.
- What features the hardware can support.
The SWL (SoftWare Licence) files define the level of service requested.
The software licenses are the encoded result of the service levels and of a unique cpu ID.
They should be loaded during the installation of the system.
The software license can be managed by either of the 2 following modes:
- Normal mode: Like for any previous release, there is no user definition and the validity of
the license in open state is not limited.
- Pay Per User (PPU) mode: This mode introduces a “user” definition and the validity of the
license in OPEN state is limited and daily checked by the system.
Note:
In Normal mode and in PPU mode, the SWL files are loaded to the system or updated manually using
OMC
Once SWL files are available on the system, either in Normal mode or in PPU mode, the
feature is the same for both modes and it manages the following functions
- Definition, modification and checking of the service level.
- Dimensioning of a system for a correct service level.
- Limitation of requested services depending on hardware installed.
- Daily or on request checking (by OMC) of the SWL files in order to adapt the service level.
- Selection between PPU mode or Normal one
- Information to user and/or installer about the state of system in terms of service level.

3.2 Software Keys

In the Alcatel-Lucent OmniPCX Office Communication Server system, a software key is
represented by an alphanumeric string of characters, which opens functions. Two software
keys correspond to each Alcatel-Lucent OmniPCX Office Communication Server system:

              3-1

Downloaded from www.Manualslib.com manuals search engine

 Chapter 3 # % $

- the PRINC (PRINCIPAL) software key or MAIN for the system functions (voice, system
feature, etc.)
- the CTI Software key for the CTI functions
The software key corresponds to a text file where the name is the CPU hardware number with
the .MSL (MAIN key) or .CSL (CTI key) extension.
Example:
file 000068DA.msl and 000068DA.csl for main CPU no. 000068DA.
Each system needs the Main and CTI Software keys even if no CTI application is used on the
system.
The systems can be delivered with a key that is already personalized for the client. The
Distributor needs to load if necessary the personalized key on the non-factory-configured
systems.
On starting up the system, different cases are possible:
- The functions needed by the customer are open and work properly: the software key
present on the system is correct.
- The functions needed are not open
- The key is valid but some functions are not open (verification done by MMC).
• Verify that the order meets the client's needs. If not, contact the orders" department. A
new software key needs to be created including the new features.
• When loading the key via OMC a warning message is displayed. In this case the
functionalities may be limited due to insufficient memory (Hard disk) or CPU power.
- The software key present on the system is not correct:
• The software key syntax is correct but it does not match the CPU's serial number. The
system functions correctly with all its functionalities for 30 days. A message " Software
Key Error " is displayed on the Operator terminal. Press the Alarm key to show the
expiry date. When loading a correct key (valid CPU serial number) during this period,
the system state is normal. If no correct key is loaded after 30 days, the system will
restart in limited state with only sets belonging to the Operator group working, all other
sets being out of service; the "Software key error" is displayed on the operator station.
• The software key syntax is incorrect. The system starts in limited mode. When loading
the correct Software key (with the correct serial number), the system restarts with all
functions working.
• New control starting with R2.0:
• The software key syntax is correct, but the software key does not match the
system's software release. The system functions correctly with all its functionalities
for 30 days.
• The software key syntax is correct, the software release is correct but a more
recent key has already been entered on this system and it is not possible to revert
to a previous key. The system functions correctly with all its functionalities for 30
days.
Remark:
For a system in limited mode, when a valid software key is loaded, the system restarts with all its
functionalities.

3.2.1 Voice Services Available in "Limited" Mode

3-2              

Downloaded from www.Manualslib.com manuals search engine

 # % $

- Stations in the default Attendant Group and analog sets with automatic call setup on going
off-hook
- no DECT stations, including DECT Reflexes stations
- Voice server with name announcement, 2 ports and 20 minutes" storage
- 4 welcome messages (pre-announcement)
- 2 system languages
- "Please Wait" music: 2 minutes max.
- All the other functions are closed.

3.2.2 Software Key Change

In BTCO mode, the software key is loaded into the system by the manufacturer; in "stock
mode" (after sale), the key must be entered by the distributor. When upgrading, the installer
must modify the key before the new functions will be taken into account.
The key is modified using OMC or DHM-station.
3.2.2.1 Procedure with OMC
- To read the series number of a CPU board: Select Typical Modification -> System ->
Software key -> Hardware serial number
- Send this serial number and the function levels required to Alcatel-Lucent Enterprise
- Load the key file Main.msl or CTI.csl from the Alcatel-Lucent Business Partner Internet site
(this file can also be downloaded by the manufacturer)
- Downloading a new software key:
• Select Typical Modification -> System -> Software key
• Click on Importing the key
• On the Open screen, select the file for the new software key
• Validate
• On the Software Key screen, click on Apply
- Opening certain functions requires a hot reset; a message is displayed.

If the hardware required to carry out the functions that have been opened by the software key
is not present, the functions available are automatically reduced to suit the available hardware;
and error message is displayed when the key is implemented.
The values of the various functions controlled by the key can be viewed at any moment:

- Using OMC, select Typical Modification -> System -> Software key
- Click on Details: the first column indicates the functions defined by the key, the second
column indicates the functions actually open (after any reductions).

3.3 Detailed description

              3-3

Downloaded from www.Manualslib.com manuals search engine

 Chapter 3 # % $

3.3.1 Services controlled by the "Main" software key

The following table lists the functions controlled by the "Main" software key. If a software key is
not present in the system, or is incorrect, the system starts in a limited state. The table also
gives the limited state service levels, the granularity of upgrades, the maximum service level
for each service, and if a hardware extension exists.
Controlled services Relevant Values in Modularity Max Hardware
software limited extension
version mode
STANDARD TELEPHONY
Number of digital sets All According to +1 236
Number of analog sets All selected +1 236
model
MOBILITY
Number of DECT sets All 0 +1 200
Number of Mobile IP Touch sets From R5.0 0 +1 120
CALL MANAGEMENT
ARS All open in open NO
DISA/Transit DISA All R1.0/R1.1, open NO
closed from
R2
ISVPN on ISDN (ARS required) All closed open NO
QSIG + (ARS required) All closed open NO
Number of Meet Me Conference From R5.1 0 +1 1
Enhanced Automated Attendant From R6.0 0 +1 5 No
(EAA)
NETWORKS
Number of B-channels All 0 +1 120
Number of B-channels on MIX boards From R4 0 +2 120
WEB APPLICATION
Number of My IC Web for Office From R8.1 0 1 50
sessions
SNMP
SNMP activation From R2.1 closed opened
RAS
number of access (b channels) From R2 0 +2 16
LAN TELEPHONY
Number of IP Phones (IP Touch) All 0 +1 200
Number of PIMphony multimedia All 0 +1 200
terminals
VoIP GATEWAY

3-4              

Downloaded from www.Manualslib.com manuals search engine

 # % $

Controlled services Relevant Values in Modularity Max Hardware

software limited extension
version mode
Number of VoIP channels From R8.0 0 +1 48 YES
Number of VoIP trunk channels All 0 +1 120 NO
From R8.0 0 +1 48 YES
VOIP
R1.0/R1.1 NO YES YES
VoIP on application board
From R8.0 NO NO NO
VOICE MAIL UNIT AND AUTOMATED ATTENDANT
Number of VMU ports All 0 port +1 8 YES
Storage capacity All 20" or 60" 10" 200 hours YES
From R5.0
Automated Attendant All closed open NO
Audiotext All closed open NO
Fax switching All closed open NO
Mailbox Greetings messages All closed open YES
Name in mailing lists All closed open YES
Recording of conversations All closed open YES
Remote customizing From R2.0 closed open NO
GREETINGS
Number of messages (16") All 4 +4 20 YES
MUSIC ON-HOLD (MOH)
Duration (minutes) All 2 min +2 min 10 min YES
MOH for multiple entities From R8.0 1 +1 4 NO
METERING
Tickets for NMC all 0 + 1000 30000 Yes
Call accounting over IP From R5.0 closed open No
Local calls from R8.1 closed (see open No
Note 2)
LANGUAGES
Number of languages all 2 1 4 Yes
MULTIPLE AUTOMATED ATTENDANT
Number of tree structures: From R6.0 closed open 5 NO
1 license for 1 tree structure
or
1 license for 5 tree structures
Pay Per User (PPU)
PPU activation From R5.0 R5 and R5.1: Not controlled by the system.
From R6: Indication that On Demand option is
enabled.

              3-5

Downloaded from www.Manualslib.com manuals search engine

 Chapter 3 # % $

Controlled services Relevant Values in Modularity Max Hardware

software limited extension
version mode
PPU license validity date From R6.0 Displayed if PPU license is enabled. It is the license
validity date.
Number of users From R6.0 From R6: Not controlled by the system:
Only used for information in OMC
SWL RELEASE
Required system release From R2 0 (R1 or +1 1 (R2) YES
R1.1) 2 (R3)
3 (R4)
4 (R5)
5 (R6)
6 (R7)
7 (R8)
ENGINE
Package level Ignored by the system
ENGINEbis
Special info for ELP Ignored by the system
Checker syst solution
Special info for ELP Ignored by the system
Checker cs type
Special info for ELP Ignored by the system
Checker PCX 01
Special info for ELP Ignored by the system
Acknowledge Code
Random code given by ecom. From R2 1 FFFF NO
EDITION
Edition number of license From R2 0 +1 FFFF NO
Automatic Call Distribution
Number of Automatic Call Distribution From R3 8 groups 0 8 YES
groups
Number of active Automatic Call From R3 5, 10, 20, or 0 32 YES
Distribution agents 32
depending
on license
Automatic Call Distribution statistics From R3 closed open YES
module
Number of agent applications From R3 0 +1 32 YES
Number of supervisors From R3 0 +1 8 YES
MANAGED SERVICES

3-6              

Downloaded from www.Manualslib.com manuals search engine

 # % $

Controlled services Relevant Values in Modularity Max Hardware

software limited extension
version mode
PROXY H323 From R3 closed open NO
MY TEAMWORK
Version From R6.1 IGNORED BY THE SYSTEM
Number of audio ports
Number of data ports
MOBILITY ON GSM
Number of mobiles of any type For R7 IGNORED BY THE SYSTEM
(MCE+NCC+My IC Mobile for iPhone
or My IC Mobile for Android)
Number of MCE mobiles (Windows)
Number of NCC mobiles (Nokia)
My IC Mobile users (same license from R8.1 0 1 50 No
used for both Apple iPhones and
Android phones)
SERVICES OVER IP
Number of Fax server ports From R7 IGNORED BY THE SYSTEM
Number of Open SIP phones From R8.1 0 1 20 (R8.1) No
60 (R8.2)
Codec Pass-Through From R8.1 closed open No
UNIVERSAL DIRECTORY ACCESS (UDA)
LDAP service From R8.1 closed open No

3.3.2 Services controlled by the “CTI” software key

The following table lists the functions controlled by the "CTI" software key.
Controlled services Relevant Default Modularity Max
software state
version
APPLICATION
PIMphony Pro All 0 +1 250
PIMphony Team All 0 +1 250
Nomadic mode From R3 0 +1 25 (R4)
50 (R5.0)
PIMphony release From R4.0 0 +1 50 (R4)
60 (R5.0)
PIMphony Attendant From R5.0 0 +1 250
Pay Per User From R5.0 Not controlled by the system
INTEGRATED TAPI 2.01

              3-7

Downloaded from www.Manualslib.com manuals search engine

 Chapter 3 # % $

Controlled services Relevant Default Modularity Max

software state
version
Number of sessions All 25 (R1) +1 200
0 (from R2)
Number of monitors All 250 (R1) +1 950
0 (from R2)
Features All None All
Alcatel-Lucent OmniPCX Office Communication Server CALL CENTER
Number of sessions All 0 +1 200
Number of monitors All 0 +1 950
Features All None All
CSTA DESKTOP CLIENT
Number of sessions All 0 +1 200
Number of monitors All 0 +1 950
Features All None All
CENTRAL SERVICES
Number of sessions All 0 +1 200
Number of monitors All 0 +1 950
Features All None All
CSTA (ALL FEATURES)
Number of sessions All 0 +1 200
Number of monitors All 0 +1 950
Features All None All
TAPI 2.1 SERVER
Number of sessions All 0 +1 200
Number of monitors All 0 +1 950
Features All None All
BUSY LAMP FIELD (BLF)
Number of sessions All 0 +1 200
Number of monitors All 0 +1 950
Features All None All
XML SERVER
Number of sessions All 0 +1 1
Number of monitors All 0 +1 950
Features All None All
PIMphony UNIFIED
Number of sessions From R3.1 0 +1 1
Number of monitors From R3.1 5 +10 75

3-8              

Downloaded from www.Manualslib.com manuals search engine

 # % $

Controlled services Relevant Default Modularity Max

software state
version
Features From R3.1 None All
SOFTWARE LICENSE VERSION
Required system version From R2 0 +1 1 (R2)
(R1/R1.1) 2 (R3)
3 (R4)
4 (R5)
5 (R6)
6 (R7)
7 (R8)
ACKNOWLEDGE CODE
Random code given by ecom. from R2 0 FFFF
EDITION
Edition of license From R2 0 +1 FFFF (Hex)

3.4 Descriptions

3.4.1 Introduction
This section describes how the licenses affect the Alcatel-Lucent OmniPCX Office
Communication Server.

3.4.2 Standard telephony

The number of sets allowed can be changed without reset, it means that all the devices are
accepted but the sets, which exceed the limit, are put out of service (as it would be done by
OMC) due to a SWL reason.
When a new SWL is entered, a search for Out Of Service sets for SWL reason is carried out
and if allowed, are put into service.

3.4.3 Alcatel Reflexes sets

The sets are taken into account in their apparition order.
When a set is not allowed, its apparition is accepted, but the set is put "Out of service" due to a
SWL reason. So if the attendant set appears after the limit is reached, it is refused.
UA sets behind TSC DECT or TSC/IP are not counted. NOE TDM sets are taken into account
in this counter.
Licensing will accept 5 more sets than the limit, only if the system is not in default state. This

1
In R1, this service is always present in the CTI software key. Only two monitors per session
are allowed.

              3-9

Downloaded from www.Manualslib.com manuals search engine

 Chapter 3 # % $

margin is only applied if the system is not in PPU mode.

3.4.4 Analog interfaces

The interfaces are taken into account in their apparition order. When there are only 10 licenses
for analog access and when the analog board contains more than 10 accesses, only the first
10 accesses will work.
When an interface is not allowed, Its apparition is recognised but the interface is put "Out of
service" (as it would be done by OMC) due to a SWL reason.
Licensing will accept 5 more interfaces than the limit, but only if the service is opened (if the
limit is different than 0) and if the system is not in default state.
This margin is only applied if the system is not in PPU mode.
A port of an external voice mail is counted as an analog set.

3.4.5 Mobility
3.4.5.1 Number of mobile sets and TSC Dect
The number of devices are limited at the set registration. When the limit is reached, the
registration is accepted but the set is put "Out of service".
All Dect sets are counted: 4072, 4074, 4073, TINY, TSC Dect and other manufacturers sets.
Licensing will accept 5 more sets than the limit, but only if the service is opened (if the limit is
different than 0).
This margin is only applied if the system is not in PPU mode.
3.4.5.2 Number of mobile IP sets
The number of devices is limited at the set registration. When the limit is reached, the
registration is accepted but the set is put "Out of service".
Licensing will accept 5 more sets than the limit, but only if the service is opened (if the limit is
different than 0). This margin is only applied if the system is not in PPU mode.

3.4.6 Call handling features

3.4.6.1 ARS
The same as for Alcatel-Lucent OmniPCX Office Communication Server.
3.4.6.2 DISA / DISA Transit
The same as for Alcatel-Lucent OmniPCX Office Communication Server.
3.4.6.3 ISVPN ISDNs
The same as for Alcatel-Lucent OmniPCX Office Communication Server.
3.4.6.4 QSIG + (Inter PABX link)
The same as for Alcatel-Lucent OmniPCX Office Communication Server.
3.4.6.5 Number of Meet-me conferences

3-10              

Downloaded from www.Manualslib.com manuals search engine

 # % $

With this license, the conference master is able to activate a Meet-me conference. Up to now,
the number of Meet-me conferences is limited to one.
3.4.6.6 Enhanced Automated Attendant
It defines the license type chosen for Enhanced Automated Attendant: (No license, 1 tree
license or 5 trees license)

3.4.7 Networking
3.4.7.1 Number of B channels
The T2, DTL2 and PCM boards are the same. A strap defines the type of board . So all boards
are treated with the same pricing.
The number of DTL b channels is counted. In case of an upgrade, a reset is necessary to take
the new channels into account.
3.4.7.2 B channels on MIX boards
The number of b channels on MIX boards are counted to accept MIX boards in the limit
allowed bythe license. This means that when a MIX board appears and all b channels allowed
by license are used, the MIX board is refused.
When the license is set to 0, only 0/4/4 MIX board are accepted.
In case of upgrade, a reset is necessary to take into account new MIX boards. In default state
reached after 30 days of temporary state, the license 2B channels on mixed board is set to 24.

3.4.8 Internet access (relevant up to R7.1)

Several services are defined in the license:
- Access & Intranet
- E mail server
- VPN (Virtual Private Network)
- Proxy (WEB caching & Access Control)
- DSL
- Lan to LAN
- Backup (backup all the system: IA, call handling, VMU )
- URL filters download (download of black lists and white lists)
- Statistics data upload (dump of log files to produce statistics)
- Web & File server (Intranet web server and file server)

3.4.9 Web applications

3.4.9.1 WCA (relevant up to R7.1)
WCA (Web Communication Assistant) license defines the number of users of three
applications. The three applications contained in the package WCA are:

              3-11

Downloaded from www.Manualslib.com manuals search engine

 Chapter 3 # % $

- web mail
- voice mail
- dialer
3.4.9.2 Number of MyIC Office sessions (from R8.1)
This application is used on a PC to access to some configuration parameters of the terminal
(diversion,…), to access to the call log, to access to the voice mail and to make a call.
The system controls the number of opened sessions in the mode of a “floating license” : when
the maximum number of allowed sessions (defined by the present item) is reached, the next
login attempt is rejected.

3.4.10 SNMP
SNMP (Simple Network Management Protocol) license allows to control «activation» of this
service.

3.4.11 RAS (relevant up to R7.1)

Control of the virtual S0. The number of B channels is counted.
Need of a downloading item RAS to have the service on a CoCPU. (2 access on ASPEN main,
2 access on CPU III main, 16 access on CoCPU)

3.4.12 Lan telephony

In the license, two counters are defined:
- The number of TSC/IP and number of PIMphony IP: Their processing is the same as for
other sets.
- The number of allowed NOE/IP are included into the TSC/IP counters.

3.4.13 VoIP Gateway

3.4.13.1 Number of VoIP channels (from R8.0)
From R 8.0 the pricing of VoIP channels is not based on hardware purchase, but on VoIP
channel licenses purchase.
Note:
To get a number of VoIP channels belonging to the range [17-48], an Armada daughter board is
necessary.
The VoIP channels are available as well for trunks as for subscribers. The number of VoIP
channels available for subscribers can be deduced with the formula:
number of VoIP channels for subscribers = number of VoIP channels – number of VoIP
channels for trunks
When the system starts, the number of available VoIP channels is indicated in OMC
In the VoIP parameters window -> General index , under the label Number of
VoIP-subscriber channels, because all the VoIP channels are allocated to subscribers and

3-12              

Downloaded from www.Manualslib.com manuals search engine

 # % $

none are allocated to the VoIP trunks.

If the number of VoIP trunks are increased (assuming that the key contains provisions for VoIP
trunks), the number of VoIP channels for subscribers decreases correspondingly. Thus, the
addition of Number of VoIP-subscriber channels and Number of VoIP-trunk channels is the
number of VoIP channels paid for by the customer.
3.4.13.2 Number of VoIP trunks channels
By default, the system starts with 0 trunk.
The number of trunks can be configured by OMC, in VoIP parameters window, index
General, with the label Number of VoIP-trunk channels.
The license gives the maximum number of VoIP trunks, which, from R8.0, cannot be greater
than the number of VoIP channels purchased.

3.4.14 Supplementary information

Supplementary information defines if the VoIP is running on the main CPU or on an application
board (not in R8.0).Voice mail and Automated attendant
Three values allow limiting Voice mail and Automated Attendant features.
- The Number of ports.
They are common to voice mail and automated attendant. In the default state, two ports
are created. They are in the attendant default group and in the first hunting group.
For example: If by configuration, you remove the two ports from the default attendant
group because you do not have automated attendant (it is not mandatory).
Then, if there is a SWL upgrade, which permits 4 ports and automated attendant, you will
need to create two new ports, present in the attendant default group and in the first hunting
group. But the two previous ports are not updated (not present in the attendant group).
If number of VMU ports is set to 0, the system is forced to external VMU mode.
- Messages storage capacity
Maximum capacity storage for messages (steps of 10 minutes)
- Automated attendant flag
In the description of license, the flag is open or closed. If the flag is «open» but there is not
enough memory, the service will be opened but it will not be possible to configure the Info
Messages. On OMC the service will be «not configurable».
If the service is not configurable, only the company greetings (day and night) can be
configured, but the length of each is reduced from 2 minutes to 16 seconds.
- Audiotext
If the service is not allowed, the call will be routed to the attendant.
- Fax switching
If the service is not allowed, the calls are routed to the voice set.
- Mailbox greetings
If the service is opened, the users can record their greetings.
- Distribute list namen
If the service is opened, the configuration is allowed.
- Record on line
- Remote customization
If the service is opened, the remote customization is allowed: personal assistant

              3-13

Downloaded from www.Manualslib.com manuals search engine

 Chapter 3 # % $

configuration, external notification, mailbox configuration.

All the services which need memory, can be reduced (message storage capacity, number of
mailbox greetings, distribute list name, record on line)

3.4.15 Music on Hold (MOH)

3.4.15.1 MOH Length
The MMC has to control the duration of the recording.
3.4.15.2 MOH for multiple entities
If the value N of that service is greater to 1 and less or equal to 4, it is possible to create on the
system N entities, each one having its own Music On Hold. Moreover, it is possible to establish
calls inter-entities.

3.4.16 Metering
3.4.16.1 Number of tickets for NMC
Only the number of NMC tickets is controlled by licenses.
In case of upgrade, a reset is necessary.
3.4.16.2 Call accounting over IP
This license is required for printing on the fly or for using external accounting applications.
Output data will be provided in a simple XML format interface.
This license must be opened for OHL needs.
3.4.16.3 Local calls (from R8.1)
Specific license for each country

3.4.17 Languages
The number of languages defines the maximum of language used. It is possible to install more
languages (for example 4) but if the number of languages defined in the license is 2, only the 2
first languages will be proposed on sets.

3.4.18 Pay Per User (PPU)

This license indicates that Pay-Per-User option is used.
In this mode, OPEN state has a limit date. At the end of the validity period (checked with PPU
Ending Date value contained in the license key), the system goes into PPU TEMPORARY
STATE for a maximum of 30 days.
At the end of this period, if the PPU Ending Date is still not valid, the system goes into
DEFAULT STATE.
The 30 days period is not the same as the “normal” TEMPORARY STATE. When a new
license key with a valid PPU Ending Date is uploaded, the PPU temporary state counter will
reset and can be used with the default value (30 days) for the next time (in “normal” temporary
state, the counter is never reset). Some Historical alarms are generated one month before the

3-14              

Downloaded from www.Manualslib.com manuals search engine

 # % $

PPU ending date and when entering to PPU temporary state.

3.4.18.1 PPU Ending Date
This field is only relevant when Pay-Per-User option is activated. It represents the end of the
validity period of the license key. After this date, license has expired and after a temporary
period, system goes to default state.
It is important to notice that, PPU mode (and the validity date) manages the control of all the
licensed services. There is no possibility to unitary close or open a single service.
If the PPU Ending date contains a null value, the license is considered as infinite. In this
particular case, there are no validity date checks.
3.4.18.2 Users number
This field is only relevant if Pay-per User option is used. This value is not used or controlled by
the system. The number of devices is only controlled with the physical device counters (Analog
sets, Mobile set, TSC-IP sets …).
This licenses is only used in the system to display, the number of users contained in the
license, in OMC license screen.

3.4.19 ACD
The Alcatel-Lucent OmniPCX Office Communication Server provides an embedded Linux
based ACD (automatic call distribution) solution. The following capacities are defined through
licenses: 1) 2) 3)
1. The Number of group: 8 groups
2. The number of active agents: 5, 10, 20 or 32
3. Statistic module: active or not
4. DAM: 0 -> 32
5. Supervisor: 0 -> 4
In the case of an upgrade, a reset is necessary.

3.4.20 Managed services

Proxy H323 services allowed or not.
In the case of an upgrade, a reset is necessary.

3.4.21 Mobility on GSM

For the related items (MCE, NCC, My IC Mobile), when eLP builds a MAIN software key, each
time the item is incremented, it also increments the Nomadic counter in the CTI software key.
3.4.21.1 Number of My IC Mobile (from R8.1)
My IC Mobile is an application running on an Apple iPhone or an Android phone, which makes
the Apple iPhone or Android phone become an OmniPCX Office subscriber.
In OMC, the creation of a new My IC Mobile for iPhone subscriber or a new My IC Mobile for
Android subscriber is refused if the total number of existing such subscribers has reached the

              3-15

Downloaded from www.Manualslib.com manuals search engine

 Chapter 3 # % $

maximum value indicated by the present license item.

3.4.21.2 Number of SIP phone enhanced (from R8.1)
The subscribers of type SIP phone enhanced can use more services that a SIP phone
subscriber. In OMC, the creation of a new SIP phone enhanced subscriber is refused if the
number of existing such subscribers has reached the maximum value indicated by the present
license item.
3.4.21.3 Number of SIP subscribers with TLS (from R8.1)
The capability to establish a VoIP communication with the TLS feature is given to a SIP
subscriber (SIP phone and SIP phone enhanced only in R8.1) via OMC. The system/OMC
controls that the number of SIP subscribers with the TLS feature activated does not exceed
the limit fixed by the present license item.
3.4.21.4 SDP transparency (from R8.1)
This license item is a global parameter (on/off) that allows or not the SDP transparency in the
SDP negotiation between 2 SIP end-points. The control is done by the system during the call
establishment, if some conditions are verified.
3.4.21.5 UDA – LDAP (from R8.1)
This license item is a global parameter (on/off) that allows or not, when a correspondent name
is searched on 8082 My IC Phone and My IC Mobile for iPhone, to extend the search to an
external LDAP server.

3-16              

Downloaded from www.Manualslib.com manuals search engine

   

       

4.1 Presentation

4.1.1 Location of Unit

The Alcatel-Lucent OmniPCX Office Communication Server unit can be installed in three
ways:
1. Fixed to the wall:
• A kit is available for wall-mounting OmniPCX Office RCE Small and OmniPCX Office
RCE Medium platforms.
• A wall support (US version) is available for wall-mounting OmniPCX Office RCE
Compact platform which can also be fixed directly to the wall. In both cases, use the
hole drilling template supplied with the platform.
2. Mounted in a rack: the OmniPCX Office RCE Small, Medium, Large platforms are mounted
in the rack using the fixing brackets supplied by the rack manufacturer, or using the
optional 19" mounting kit (a kit is available for each platform type).
3. Placed on a table: no more than three units can be laid on top of each other.
4.1.1.1 Wall Mounting (OmniPCX Office RCE Small and OmniPCX Office RCE
Medium platforms)
The enclosure comprises 4 parts.
After mounting, the space between the platform and the wall can be used for cables.

              4-1

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

4.1.1.2 Mounting in the 19" Rack

4.1.1.2.1 Recommendations
Before installing the system in a 19" rack, you must verify that:
- The maximum static load (given by the manufacturer) of the 19" rack is greater than the
overall weight of the equipment mounted or to be mounted in the rack.
- Moreover, the weight of the equipment must be evenly distributed between the brackets.
- If mounting the Alcatel-Lucent OmniPCX Office Communication Server platform results in
exceeding the load on the front supports (generally the total weight divided by two), the
platform must be placed on a fixed tray attached to the four supports of the rack.

4-2              

Downloaded from www.Manualslib.com manuals search engine

     &' (

4.1.2 Environment
4.1.2.1 Climatic Conditions
- Operation
• Temperature: for maximum reliability, it is recommended you comply with an ambient
temperature of between 5 and 40 degrees Celsius, with a maximum variation of 5
degrees Celsius per hour.
• Humidity: the humidity must be in the range 10% - 80% (no condensation) with a
maximum variation of 10% per hour.
- Storage
• Temperature: the temperature must be kept between -20 and +70 degrees Celsius.
• Humidity: the humidity must be kept in the range 10 - 95% (no condensation).
4.1.2.2 Vibration
No vibration, even intermittent, may be transmitted to the equipment when running.
4.1.2.3 Site
- Choose a dry, clean and well ventilated location.
- Maintain an ambient air flow to ensure normal ventilation. If the air flow is blocked or
restricted, of the incoming air is too hot, overheating is possible.
- When installing the equipment in an enclosed 19" rack, verify that the rack is provided with
a fan suited to the heat dissipation of the equipment installed. Maintain a minimum gap of 3
cm around the side ventilation holes (left and right sides), and of 10 cm minimum around
the ventilation holes at the rear of the equipment. Verify that the air flow is not impeded on
the sides of the rack.
- When fixing the system directly to the wall using the wall-mounting kit (OmniPCX Office
RCE Small and OmniPCX Office RCE Medium platforms only), maintain a free space of at
least 15 cm around the whole system. Ensure that no objects are placed on the upper part
of the system to restrict the extraction of hot air. When installing several platforms, it is
preferable to align then horizontally. When superposing them vertically, they should be
separated by at least 10 cm.
- Verify that the cables connecting the Alcatel-Lucent OmniPCX Office Communication
Server or other equipment, or the supports for the housing structure (19" rack for example)
do not obstruct the air flow through the platform.
- A switchable 230 V or 110 V mains socket (according to country) - 50Hz (LNE) is required
at less than 1 m from the platform unless it is installed in a rack in which case the
integrated circuit breaker is used.
- Adequate lighting must be provided.

4.2 Connections and Cabling

4.2.1 Detailed description

4.2.1.1 Output Connectors

              4-3

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

All outputs are made using Female RJ45 connectors.

4.2.1.1.1 PowerCPU Board

RJ45 pin 1 2 3 4 5 6 7 8
LAN TX+ TX- RX+ RX-
CenRG
SLI1/SLI2 Ground +12 V CenRg A ZA1 ZB1 ZA2 ZB2
B
CenRG
AUX Ground +12 V CenRg A
B
CONFIG CTS RX RMTRES Ground TX DTR RTS
MODULE1 TX+ TX- RX+ RX-
ISDN T01 TX+ RX+ RX- TX-
MODULE2 TX+ TX- RX+ RX-
ISDN T02 TX+ RX+ RX- TX-
Audio In Audio Audio Audio Audio
AUDIO Audio In A Alarm A Alarm B
B Ctrl A Out A Out B Ctrl B
DOORPHONE DoorPhB1DoorPhA1 DoorPhA2DoorPhB2

- LAN: 10/100/1000 base T Ethernet port (MDI-II/straight).

- SLI1/SLI2: Analog Z accesses from Mini-MIX board, General ringer; 12V output
- AUX: General ringer; 12V output
- CONFIG: RS232 for OMC.
- MODULE1: HSL1 link of HSL board for connection to module expansion 1
- ISDN T01: ISDN T01 port of Mini-MIX board
- MODULE2: HSL2 link of HSL board for connection to module expansion 2
- ISDN T02: ISDN T02 port of Mini-MIX board
- AUDIO: Interfaces Please wait message, Background music, Loudspeaker, Alarm
- DOORPHONE: Interfaces doorphone
4.2.1.1.2 SLI Board

RJ45 pin 1 2 3 4 5 6 7 8
1 to 16 ZA ZB

- 1 to 16: connecting analog Z terminals.

4-4              

Downloaded from www.Manualslib.com manuals search engine

     &' (

4.2.1.1.3 UAI Board

RJ45 pin 1 2 3 4 5 6 7 8
1 to 16 (UAI) L1 L2

- 1 to 16: connection of digital terminals or DECT 4070 IO/EO base stations.

4.2.1.1.4 UAI-1 Board

RJ45 pin 1 2 3 4 5 6 7 8
1 L1 L2 0V 48V
2 to 16 L1 L2

- 1 : connection of an EPS48 external power supply + connection of digital terminals or

DECT 4070 IO/EO base stations.
- 2 to 16: connection of digital terminals or DECT 4070 IO/EO base stations.
4.2.1.1.5 BRA Board

RJ45 pin 1 2 3 4 5 6 7 8
1 to 8 TX+ RX+ RX- TX-

- 1 to 8: connection of T0/DLT0 basic access.

4.2.1.1.6 PRA Board

RJ45 pin 1 2 3 4 5 6 7 8
NETW outputs RX+ RX- TX+ TX-
PBX outputs TX+ TX- RX+ RX-

- NETW: connection to the public network (TNL).

- PBX: use in private network with TX and RX twisted pairs.
4.2.1.1.7 LANX and LANX-1 Board

RJ45 pin 1 2 3 4 5 6 7 8
Ports 1 to 15 RX+ RX- TX+ TX-
Up-Link TX+ TX- RX+ RX-

- Ports 1 to 15: internal ports.

- Up-Link: LAN connection.
4.2.1.1.8 LANX-2 Board

RJ45 pin 1 2 3 4 5 6 7 8
Ports 1 to 14 RX+ RX- TX+ TX-
GE1, GE2 TR0+ TR0- TR1+ TR2+ TR2- TR1- TR3+ TR3-

              4-5

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

- Ports 1 to 14: 10/100 BT ports.

- GE1, GE2: 10/100/1000 BT ports.
4.2.1.1.9 APA Board

RJ45 pin 1 2 3 4 5 6 7 8
Output 1 ZSETB ZSETA LB-Ring LA-Tip ZB ZA
Outputs 2 to 8 LB-Ring LA-Tip

- 1 : connection of network line 1, SLI interface and callback terminal

- 2 to 8: connection of other analog trunk lines
4.2.1.1.10 DDI Board

RJ45 pin 1 2 3 4 5 6 7 8
1 to 4 L- L+

- 1 to 4: connection of DDI analog trunk lines.

4.2.1.1.11 ATA Board

RJ45 pin 1 2 3 4 5 6 7 8
Outputs 1 to 4 PEA PEB
SLI outputs ZA ZB
PHONE outputs ZSETA ZSETB

4.2.1.2 Types of Cable to Use

Access Type Impedance

Digital, Z, T0, LR UTP, FTP or STP, Category 3 or 5 100 or 120 ohms
T2 UTP, FTP or STP, Category 3 or 5 120 Ohms
T1 UTP, FTP or STP, Category 3 or 5 120 Ohms
Ethernet FTP or STP, Category 5 100 Ohms
HSL STP supplied with the product, Category 5 100 Ohms

- UTP: Unshielded Twisted Pairs

- FTP: Foiled Twisted Pairs
- STP: Shielded Twisted Pairs
4.2.1.3 Connection of PowerCPU Board

4-6              

Downloaded from www.Manualslib.com manuals search engine

     &' (

4.2.1.4 Connecting Terminals

4.2.1.4.1 Connection of Digital Terminals
The terminals are equipped with a cable and a self-acting switch that plugs into the wall
socket. Each terminal is connected up by a pair of 0.5 or 0.6 mm diameter wires.
System - digital terminal distances:
- 0.5 mm SYT type cable: 800 m (station without option) or 600 m (station with S0 or Z
option).
- 278 type 0.6 mm cable: 1200 m (station without option) or 850 m (station with S0 or Z
option).
Connection without External Power Supply

              4-7

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

Connection with External Power Supply

A splitter allows the separation of the UA peripheral connection and the EPS48 external power
supply.

4.2.1.4.2 Connecting Analog Terminals

The terminals are equipped with a cable and a self-acting switch that plugs into the wall
socket. Each terminal is connected up with a pair of 0.5 or 0.6-mm diameter wires (the
maximum distance with 0.5-mm cabling is 1.3 km).

4-8              

Downloaded from www.Manualslib.com manuals search engine

     &' (

4.2.1.5 Connection to the Public Network

4.2.1.5.1 Digital Public Network via T0 Access (or DLT0 Private Network)
The Alcatel-Lucent OmniPCX Office Communication Server system can be installed near the
digital network termination or at a certain distance (up to 350 m), as required.
Connection without T0/S0 Forwarding

Caution:
In T0 Point-to-Point installations, the Alcatel-Lucent OmniPCX Office Communication Server
system MUST BE the terminating element of the bus and any other terminating resistor MUST BE
removed.

Connection with T0/S0 Forwarding

In the event of a loss of tension or PowerCPU malfunction, the ISDN-EFM box allows a T0
access to be forwarded directly to a S0 station.
Caution:
The AFU-1 board (daughter board of the PowerCPU board) must obligatorily be fitted to detect the
absence of power.

              4-9

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

The ISDN-EFM box must be installed as close as possible to the system (3 m maximum). All
the box connections are made with straight RJ45-RJ45 cables.
Output connector functions:
- BRA: connection of T0 access to be forwarded.
- NT: connection of ISDN network termination.
- S0: connection of forwarding S0 station.
- CPU: connection of the AUDIO and AUX connectors of the PowerCPU board.
- AUX: connection of Audio out, Alarm, General bell and 12 V use auxiliaries.

4-10              

Downloaded from www.Manualslib.com manuals search engine

     &' (

4.2.1.5.2 Digital Public Network by T1 or T2 Access

The diagram below shows a PRA-T2 board, but is equally applicable for a PRA-T1 board.

              4-11

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

The PRA board is connected to a digital line termination (DLT) by 2 symmetrical twisted pairs.
Cable impedance: 120 Ohms +/- 20% between 200kHz and 1MHz; 120 Ohms +/- 10% at 1
MHz.
Remark:
We recommend using an L120-series cable (or the L204 equivalent).
The distance T1-DLT or T2-DLT is limited by the amount of loss between the DLT and T1/T2,
which must not exceed 6 dB at 1024 kHz.
4.2.1.5.3 Analog Public Network
Without TL Forwarding

With LR Forwarding
In the event of a loss of tension or PowerCPU malfunction, this solution allows forwarding of
the analog line, connected to the APA board's equipment 1, to an analog station.

4-12              

Downloaded from www.Manualslib.com manuals search engine

     &' (

4.2.1.5.4 Analog Public Network - Direct Dialing In.

4.2.1.6 Lan Connection

The LANX8/LANX16 board is used to connect servers, PCs, IP terminals and external
switches.

              4-13

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

Category 5 cable, FTP or STP, impedance 100 Ohms: maximum length 100 m.
4.2.1.7 Connecting Auxiliary Equipment
All auxiliary equipment is connected via the AUDIO, AUX and DOORPHONE connectors of the
PowerCPU board.
4.2.1.7.1 Connecting a Please-Wait Message Player
This is connected via the AUDCTRL output (control contact open when idle) and the AUDIN
input of the AUDIO connector.

4-14              

Downloaded from www.Manualslib.com manuals search engine

     &' (

Audio Input Characteristics:

Input impedance : 600 Ohms
Fuse Characteristics:
- Max. power : 10 W
- Max. voltage : 60 V
- Max. current : 500 mA
The contacts of the alarm and doorphone controls have the same electrical

characteristics as those indicated above.

4.2.1.7.2 Connecting a Background Music Tuner
This is connected via the AUDIN input of the AUDIO connector.

Audio Input Characteristics:

- Input impedance : 600 Ohms
- Input level: access + 4.7 dBr or + 15 dBr

              4-15

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

4.2.1.7.3 Connecting an Alarm

The alarm is activated in the event of a false stopping of the system.
It is connected via the ALARM output (control contact closed when idle) of the AUDIO
connector.

4.2.1.7.4 Connecting a Broadcast Loudspeaker

Broadcast loudspeakers are connected via the AUDOUT output of the AUDIO connector.

Audio Output Characteristics:

- Output impedance: < 500 Ohms
- Output level: access + 3 dBr
4.2.1.7.5 Connecting a General Ringer
The general ringer is connected via the CENRG output of the AUX connector.

4-16              

Downloaded from www.Manualslib.com manuals search engine

     &' (

4.2.1.7.6 Connecting a Doorphone

2 doorphone types are available, depending on the operating mode used:
- Type A: relay-controlled doorphones (e.g. NPTT)
- Type B: doorphones controlled by MF Q23 signals requiring an SLI interface (e.g.
TELEMINI and UNIVERSAL DOORPHONE)
The doorphone interface comprises an intercom and an optional latch powered by the mains
supply through a SELV (Safety Extra Low Voltage) transformer.
It is connected via the DOORPHA and DOORPHB outputs (control contacts open when idle)
of the DOORPHONE connector.
Connecting a NPTT Doorphone

              4-17

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

- A single doorphone with doorstrike may be connected to the system.

- The system also allows for the connection of 2 doorphones without latch.
Connecting a Telemini and Universal Doorphone
These doorphones require the use of a Z station interface.
- Several of these doorphones can be connected to the system; the limit is determined by
the maximum number of analog stations the system can support.

4-18              

Downloaded from www.Manualslib.com manuals search engine

     &' (

4.2.1.7.7 Using the 12V Output

The GROUND and + 12V outputs on the AUX connector allow for the connection of an
external 12V device with a maximum energy consumption of 150 mA (OmniPCX Office RCE
Small and OmniPCX Office RCE Medium) or 300 mA (OmniPCX Office RCE Large).

4.3 Power Supply

4.3.1 Installation procedure

4.3.1.1 Connecting an External EPS48 Power Supply
The UAI16-1 board can optionally be powered by an external EPS48 power supply depending
on the requirements for remotely powering the terminals.
The mains socket for the external EPS48 power supply must be installed as near as possible
to the system and be easily accessible.
Caution:
Only use the recommended power supply provided. It is guaranteed to operate at 40#C for a
current load of 0.85A. Its use is limited to UAI16-1 boards.
The power supply lead is used as the master switch. The power supply socket

must be located or installed close to the hardware and allow easy access.
The power supply cord is used as the main disconnect device, ensure that the

socket-outlet is installed near the equipment and is easily accessible.

4.3.1.2 Battery Implementation
Alcatel-Lucent OmniPCX Office Communication Server is supplied with one or more integrated
batteries; they are mounted and fixed with a solid bar on the rear plate.
Caution:
OmniPCX Office RCE Compact does not have integrated batteries.

4.3.1.2.1 Battery Switch

The batteries are disconnected during transport using a switch soldered onto the power supply
board. When the mains cable is inserted in the socket, the switch is closed by a lever
incorporated in the mains socket.
4.3.1.2.2 Battery Fuse
The battery fuse is located on the board and requires the back panel to be dismantled to gain
access. It has the following characteristics:
- OmniPCX Office RCE Small and OmniPCX Office RCE Large: 6.3 A fast, low cutoff (F 6.3
AL/250 V).
- OmniPCX Office RCE Medium: 10 A fast, low cutoff (F 10 AL/250 V)
4.3.1.2.3 Battery Replacement

              4-19

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

Refer to the Maintenance form in the manual.

4.3.1.3 Connecting an External Battery Unit
Alcatel-Lucent OmniPCX Office Communication Server hardware units (OmniPCX Office RCE
Small, Medium, Large and OmniPCX Office RCE Compact) can be powered by external
batteries. The use of external batteries is an alternative to the UPS solution. It ensures that the
Alcatel-Lucent OmniPCX Office Communication Server systems are backed up. This solution
offers a maximum autonomy of 8 hours.
4.3.1.3.1 Alcatel-Lucent OmniPCX Office Communication Server Platforms that accept
External Batteries
The following platforms can be powered by external batteries:
Platform (with power supply) Reference
OmniPCX Office RCE Compact platform 3EH 08271 AA
OmniPCX Office RCE Small platform with 110-230V power 3EH 08227 AA
supply
OmniPCX Office RCE Medium platform with 230V power 3EH 08228 AA
supply
OmniPCX Office RCE Medium platform with 110V power 3EH 08228 AB
supply
OmniPCX Office RCE Large platform with 230V power supply 3EH 08229 AA
OmniPCX Office RCE Large platform with 110V power supply 3EH 08229 AB

Before using external batteries, first remove any internal batteries installed in the

platform (supplied in the OmniPCX Office RCE Small, Medium, Large platforms by default).
4.3.1.3.2 Hardware
External battery units are available in different versions. The required version depends on your
Alcatel-Lucent OmniPCX Office Communication Server platform, as shown in the table below.
Alcatel-Lucent External battery unit Battery capacity Reference
OmniPCX Office
Communication
Server platform
OmniPCX Office 36V, rack version Up to 6 batteries 3EH 76155 AB
RCE Large 36V, stack version Up to 6 batteries 3EH 76177 AC
OmniPCX Office 12V, rack version Up to 3 batteries 3EH 76155 AA
RCE Medium 12V, stack version Up to 3 batteries 3EH 76177 AB
OmniPCX Office
RCE Small
OmniPCX Office 12V, 4-hour, stack version 1 battery 3EH 76177 AA
RCE Compact 12V, 8-hour, stack version Up to 2 batteries 3EH 76177 AD

Note:
The external battery units for OmniPCX Office RCE Small, Medium, Large platforms are pre-wired and

4-20              

Downloaded from www.Manualslib.com manuals search engine

     &' (

delivered with inter-battery connectors.

In addition, you will need:
- 12V - 7Ah batteries (reference: 3EH 76156 AA)
- A connection kit (reference: 3EH 75031 AA) for connecting the external battery unit to the
Alcatel-Lucent OmniPCX Office Communication Server platform.
4.3.1.3.3 Power Supply Reference

Type Reference
110-230V power supply for OmniPCX Office RCE Small 3EH 05009 AC
platform
230V power supply for OmniPCX Office RCE Medium platform 3EH 05012 AC
110V power supply for OmniPCX Office RCE Medium platform 3EH 05010 AC
230V power supply for OmniPCX Office RCE Large platform 3EH 05013 AC
110V power supply for OmniPCX Office RCE Large platform 3EH 05011 AC

4.3.1.3.4 Installation of External Batteries for OmniPCX Office RCE Small, Medium,
Large Platforms
You must first prepare the external battery unit for use and then connect this unit to the
platform. These two phases of installation are presented separately below.
You will have to choose the appropriate preparation procedure, according to whether you have
a rack or stack version of the external battery unit.
The connection procedure is the same for OmniPCX Office RCE Medium and OmniPCX Office
RCE Large platforms, but is different for OmniPCX Office RCE Small platforms.
Preparing an External Battery Unit (Rack Version)
Before starting the installation, note that:
- External batteries must be of the same type, must be supplied by the same manufacturer
and be from the same batch run.
- Batteries must be charged prior to installation.

              4-21

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

Figure 4.24: Wiring Diagram of a 12V External Battery Rack Unit (2 or 3x7Ah in parallel)

Figure 4.25: Wiring Diagram of a 36V External Battery Rack Unit (1 or 2x7Ah in parallel)
This type of unit is only used for an OmniPCX Office RCE Large platform.

Procedure
Position the 12V - 7Ah external batteries in the battery rack unit (maximum 3 batteries for an
OmniPCX Office RCE Medium platform and 6 batteries for an OmniPCX Office RCE Large
platform).
1. Open the external battery unit and position the batteries vertically in the unit.
2. Make all the connections after having removed, if necessary, the insulation devices from
the connectors that are used.
3. Place the batteries flat in the unit and close it.
4. Turn off the switch, and check the battery voltage directly on the connector at the rear of
the unit.
Preparing an External Battery Unit (stack Version)
Before starting the installation, note that:
- External batteries must be of the same type, must be supplied by the same manufacturer
and be from the same batch run.
- Batteries must be charged prior to installation.
Procedure for 12 V stack version (for OmniPCX Office RCE Small and OmniPCX Office
RCE Medium platforms)
The 12 V stack version of the external battery unit can be used with OmniPCX Office RCE
Small and OmniPCX Office RCE Medium platforms. It uses 12V - 7Ah batteries. Either one
battery or three batteries can be installed in the unit.
1. Ensure that the ON/OFF switch on the external battery unit is set to the OFF position (0 or

4-22              

Downloaded from www.Manualslib.com manuals search engine

     &' (

black) and that there is no cable connected to the J1 connector (see the figure below).

2. Open the unit by removing the four screws (ST3.5x32) with a screwdriver (Phillips PH2).
3. Insert the batteries in the open unit as follows (also see the figure below):
a. Place the first battery in the middle position (battery B2).
b. If three batteries are to be used, place these batteries in the remaining positions
(batteries B1 and B3).

4. Connect the negative (black) terminals of the batteries as described below (and shown in
the figure below).
a. Connect the middle connector of the black wire to the negative (black) terminal of
battery B2.
b. If required, connect the other connectors of the black wire to the negative (black)
terminals of batteries B1 and B3.

              4-23

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

5. Connect the positive (red) terminals of the batteries as described below (and shown in the
figure below).
a. Connect the middle connector of the red wire to the positive (red) terminal of battery
B2.
b. If required, connect the other connectors of the red wire to the positive (red) terminals
of batteries B1 and B3.

6. Close the unit and secure it with the four screws.

7. Stick a label on the unit stating the date of the installation and the number of batteries
installed.
Procedure for 36 V stack version (for OmniPCX Office RCE Large platforms)
The 12 V stack version of the external battery unit can be used with OmniPCX Office RCE
Large platforms. It uses three 12V - 7Ah batteries. Two external battery units can be
connected in parallel to obtain the autonomy achieved with six batteries.

4-24              

Downloaded from www.Manualslib.com manuals search engine

     &' (

1. Ensure that the ON/OFF switch on the external battery unit is set to the OFF position (0 or
black) and that there is no cable connected to the unit (see the figure below).

2. Open the unit by removing the four screws (ST3.5x32) with a screwdriver (Phillips PH2).
3. Insert the three batteries in the open unit, into the positions B1, B2 and B3 (see the figure
below).

4. Connect the terminals of the batteries strictly in the order detailed below (also see the
figure below).
a. Connect the black wire to the negative (black) terminal of battery B1.
b. Connect a yellow wire between the positive (red) terminal of battery B1 and the
negative (black) terminal of battery B2.
c. Connect a yellow wire between the positive (red) terminal of battery B2 and the
negative (black) terminal of battery B3.
d. Connect the red wire to the positive (red) terminal of battery B3.

              4-25

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

5. Close the unit and secure it with the four screws.

6. Stick a label on the unit stating the date of the installation and the number of batteries
installed.
7. If you wish to use two external battery units in parallel, continue as follows (also see figure
below):
a. Place the two units side by side, or one on top of the other.
b. Decide which unit is to be the principal unit and which is to be the extension unit.
c. Connect the two units using the extension cable between the J2 connectors on the
units; the cable's Mate-N-Lok 3-terminal connector must be connected to the principal
unit and its Mate-N-Lok 2-terminal connector must be connected to the extension unit.

Installation of External Batteries for the OmniPCX Office RCE Medium and
OmniPCX Office RCE Large Platforms

4-26              

Downloaded from www.Manualslib.com manuals search engine

     &' (

1. Stop the Alcatel-Lucent OmniPCX Office Communication Server system, and remove the
power supply cord from the platform side.
Disconnect the power supply cable on the platform side before handling the power
supply. This operation disconnects the mains supply and the internal battery.
Disconnect the mains inlet on the platform side before manipulating the power
supply. This process disconnects the mains and the internal battery.
2. Remove the metal panel at the rear.
3. Remove the cover from the hole provided for the connecting cable on the rear panel of the
Alcatel-Lucent OmniPCX Office Communication Server.

4. Remove the fan connector, then remove the power supply unit and the battery unit.

5. Replace the battery cable with the new cable provided with the connection kit (3EH 75031
AA).
6. If the BAT IN/EXT connector is present, remove the red jumper.

7. Remove the mounting clip and the batteries from the internal battery support.
8. Put the empty battery support and the power supply unit back in place, and reconnect the
fan connector.
9. On the rear panel, plug the connector into the slot at the back. Secure the ferrite using the
bracket and the self-adhesive base.
10. Put the rear panel back in place and stick the label provided beneath the connector. The
labels have the following texts:
• "EXTERNAL BATTERY 12VDC/8A" for OmniPCX Office RCE Medium platform,
• "EXTERNAL BATTERY 36VDC/3.5A" for OmniPCX Office RCE Large platform.
11. Connect the cable (with J1 connector) between the Alcatel-Lucent OmniPCX Office
Communication Server system and the external unit.
12. Set the ON/OFF switch on the external battery unit to the ON position (I or red).
13. Leave the batteries to charge for at least one hour.
14. Test the autonomy of the system by disconnecting the external battery unit from the mains
supply for one minute. During this time, check that the system is still powered.
Installation of External Batteries for the OmniPCX Office RCE Small Platforms
1. Stop system, and remove the power supply cord from the platform side.
Disconnect the power supply cable on the platform side before handling the
power supply. This operation disconnects the mains supply and the internal battery.
Disconnect the mains inlet on the platform side before manipulating the power
supply. This process disconnects the mains and the internal battery.
2. Use a screwdriver to remove the upper panel.
3. Remove the battery and its cable.
4. If the BAT IN/EXT connector is present, remove the red jumper.

              4-27

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

5. Remove the cover from the hole provided for the connecting cable on the rear panel of the
Alcatel-Lucent OmniPCX Office Communication Server and stick the "EXTERNAL
BATTERY 12VDC/8A" label.

6. Connect the cable provided with the installation kit, and plug the connector into the rear
panel and the slot. Secure the ferrite using the bracket and the self-adhesive base in the
battery housing.
7. Put the upper cover back in place.
8. Connect the cable (with J1 connector) between the Alcatel-Lucent OmniPCX Office
Communication Server system and the external unit.
9. Set the ON/OFF switch on the external battery unit to the ON position (I or red).
10. Leave the batteries to charge for at least one hour.
11. Test the autonomy of the system by disconnecting the external battery unit from the mains
supply for one minute. During this time, check that the system is still powered.
4.3.1.3.5 Installation of External Batteries for the OmniPCX Office RCE Compact
Platform
You must first prepare the external battery unit for use and then connect this unit to the
OmniPCX Office RCE Compact platform. These two phases of installation are presented
below in separate procedures.
Before starting the installation, note that:
- External batteries must be of the same type, supplied by the same manufacturer and from
the same batch run.
- Batteries must be charged prior to installation.
Preparing the External Battery Unit
1. On the external battery unit (see the figure below):
a. Ensure that the mains power cable is NOT connected.
b. Ensure that the ON/OFF switch is set to the OFF position (O or black).
c. Ensure that the J1 jack is NOT connected to the OmniPCX Office RCE Compact
platform.
d. Open the unit by removing the four screws (ST3.5x32) with a screwdriver (Phillips
PH2).

4-28              

Downloaded from www.Manualslib.com manuals search engine

     &' (

2. Insert the batteries in the open unit as follows (see the figure below):
a. Place the first battery in the middle position (battery B1).
b. If a second battery is to be used, place this battery in the remaining position (battery
B2).

3. Connect the negative (black) terminals of the batteries as described below (and shown in
the figure below).
a. Connect the middle connector of the black wire to the negative (black) terminal of
battery B1.
b. If required, connect the end connector of the black wire to the negative (black) terminal

              4-29

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

of battery B2.

4. Connect the positive (red) terminals of the batteries as described below (and shown in the
figure below). Note that there may be a small amount of electrical arcing when electrical
contact is made.
a. Connect the middle connector of the red wire to the positive (red) terminal of battery
B1.
b. If required, connect the end connector of the red wire to the positive (red) terminal of
battery B2.

5. Close the unit and secure it with the four screws.

6. Stick a label on the unit stating the date of the installation and the number of batteries
installed.
Connecting to the OmniPCX Office RCE Compact Platform
1. Switch off the Alcatel-Lucent OmniPCX Office Communication Server system and then:
a. Unplug the power cable from the mains socket.
b. Disconnect the mains adapter from the OmniPCX Office RCE Compact platform.
c. Using a screwdriver, unscrew the power supply module (PSXS or PSXS-N) from the
side of the OmniPCX Office RCE Compact platform and pull the module out of the
cabinet.
2. Move the red extBAT jumper from the NO position to the YES position.

4-30              

Downloaded from www.Manualslib.com manuals search engine

     &' (

Note:
If a hard disk is installed on an OmniPCX Office RCE Compact platform, it is MANDATORY to install
the external battery unit, and the extBAT jumper of the PSXS-N MUST be set to YES. It is
mandatory to use a power supply module PSXS-N with reference 3EH73072ACxx on an OmniPCX
Office RCE Compact platform equipped with a PowerCPU board and a hard disk.
3. Push the power supply module back into the cabinet and secure it in place with a
screwdriver.
4. Now on the external battery unit:
a. Ensure that the 12V stack battery unit has been properly prepared (as above).
b. Ensure that the ON/OFF switch is set to the OFF position (O or black).
c. Connect the J1 jack from the external battery unit to the OmniPCX Office RCE
Compact platform.
d. Ensure that the mains power cable is connected to the external battery unit, plug this
cable into the mains supply and check that the green LED on the unit is illuminated.
e. Set the ON/OFF switch to the ON position (I or red).
5. Restart the system.
6. Leave the batteries to charge for at least one hour.
7. Test the autonomy of the system by disconnecting the external battery unit from the mains
supply for one minute. During this time, check that the system is still powered.
4.3.1.4 Connecting a UPS

Note:
This paragraph is not relevant to the OmniPCX Office RCE Compact platform.
A UPS (Uninterruptible Power Supply) can be used to allow system data to be saved for at
least an hour in the event of mains failure.
___change-begin___
              4-31

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

___change-end___
It is connected via the mains socket at the rear of the platform:
- UPS Power: use the mains cable provided with the Alcatel-Lucent OmniPCX Office
Communication Server module.
- UPS Connection - module: use the cable supplied with the UPS
For an installation using 3 Alcatel-Lucent OmniPCX Office Communication Server modules, 2
UPSs are required: one feeds two of the modules, the other feeds the third module.
4.3.1.5 Mains Connection - Ground Connection
4.3.1.5.1 OmniPCX Office RCE Small, Medium, Large
The connection can be made using electrical installations of the following type:
- TT (local ground for each piece of equipment).
- TN (common ground for all equipment).
- IT with inter-phase voltage of 230 V; only possible in Norway.
Mains socket fuse: T2.5 AH / 250 V (delayed action, high cutout).
So as not to compromise the fire protection feature, replace fuses with the same

type of fuse having the same nominal characteristics.

For continued protection against risk of fire, replace only with same type and

rating of fuse.
The system is delivered with a 3 conductor cable (length: 3 m) to connect to the mains socket.
Permanent Ground
It is essential to connect the system permanently to ground due to leakage currents greater
than 3.5 mA over the whole line access (safety constraint CEI60950 ed.03). To do this, use the
ground wire of minimum section 4 mm2 provided and connect it to the tag at the rear of the unit
(left hand side).
For performance and safety reasons, the system must always be connected to the

ground. The ground must be connected prior to all the other connections.

4-32              

Downloaded from www.Manualslib.com manuals search engine

     &' (

For performance and safety reasons, the whole system must always be coupled

to the ground. The ground must be connected before any other connections.
The ground protection connection terminal must always be connected to the

ground. Protective grounding terminal shall be permanently connected to the ground.

4.3.1.5.2 OmniPCX Office RCE Compact
OmniPCX Office RCE Compact platform is powered by an external power supply unit
(100/240V). It is connected via a jack plug at the front of the module (right hand side).
Remarks:
- A mains cable is not supplied with the module. It must be ordered separately.
- For a more secure configuration, an AC/DC power supply, including a backup battery, can be
purchased as an optional extra.

Permanent Ground
It is essential to connect the system permanently to ground due to leakage currents greater
than 3.5 mA over the whole line access (safety constraint CEI60950 ed.03).
To do this, use the ground wire of minimum section 2.5 mm2 (not supplied) and connect it to
the tag on the metal bottom of the unit (right hand side).
For performance and safety reasons, the system must always be connected to the

ground. The ground must be connected prior to all the other connections.
For performance and safety reasons, the whole system must always be coupled

to the ground. The ground must be connected before any other connections.
The ground protection connection terminal must always be connected to the

ground. Protective grounding terminal shall be permanently connected to the ground.

4.3.1.6 Power Up
Having made all the connections, it is now time to power up the system.
- Insert the mains cable in the socket on the rear of the unit.
- Press the ON/OFF button. The system will reinitialize (duration: 3 to 4 minutes).
To stop the system:
- Press the ON/OFF button, the RED LED will flash.
- Wait until the LED stops flashing and is lit steadily (between 15 seconds and 3 minutes
depending on the configuration): the system is switched off.
4.3.1.6.1 Power Up of Dedicated Terminals
On powering up, dedicated sets execute a self-test:
- Display Test
- Test of the LEDs or icons on the terminal and add-on module, if any

              4-33

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

- Audio test
If this sequence is correct, the display on the dedicated terminals shows the system date:
Monday 01 January 00h00.
After powering up, you can activate the system from a dedicated terminal or by OMC (refer to
the specific notice).

4.4 SIP Terminals

4.4.1 8082 My IC Phone

4.4.1.1 Commissioning
4.4.1.1.1 Overview
This module presents all the actions required for commissioning the 8082 My IC Phone sets.
___change-begin___
___change-end___
Figure 4.40: 8082 My IC Phone set layout
The following figure illustrates the connectors on the base of each set.
___change-begin___
4-34              

Downloaded from www.Manualslib.com manuals search engine

     &' (

___change-end___
Figure 4.41: 8082 My IC Phone set connectors

4.4.1.1.2 Commissioning the set

This section describes how to commission the set in the two available initialization options:
- Static initialization: commissioning is manual on the set and through OMC
- Dynamic initialization (DHCP): no commissioning is needed, 8082 My IC Phone sets are
fully plug & phone
Depending on the selected mode, the set commissioning is different.
For static initialization, the operation order is as follows:
1. Configure the user in OMC, refer to: Configuring the user in OMC
2. Connect the set, refer to: Connecting the set
3. Configure network parameters on the set, refer to Configuring network parameters for
static initialization
For dynamic initialization, the operation order is as follows:
1. Configure the DHCP Server, refer to Configuring the DHCP server for dynamic initialization

              4-35

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

2. Configure the user name and password in OMC, refer to Configuring the user name and
password in OMC
Prerequisites
- The Alcatel-Lucent OmniPCX Office Communication Server version must be R810 or
higher and the system must be operational
- For network configuration, any of the following must be implemented:
• In dynamic mode, a DHCP server must be configured
• In static mode, a free IP address must be available for the set
- A port with PoE must be available on a switch. If not available, a PoE injector must be
used
Configuring the user in OMC

Note:
In dynamic (DHCP) mode,8082 My IC Phone sets are fully plug & phone. This operation is not
mandatory.
To create an 8082 My IC Phone:
1. In OMC, go to Users/Base stations List.
2. Select a No., IP access and click the Add button.
3. Select IP terminal and click OK.
4. Select the newly created user in the list, select 8082 My IC Phone in the combo box type
and enter a name.
5. Click the Modify button.
6. Double-click the newly created user to open the User dialog box.
7. Click the IP/SIP button and enter the MAC address of the set in the IP Parameters tab.
8. If needed, in the SIP Parameters tab, click the SIP password reset button to get a new
password.
Connecting the set
This section describes how to:
- Connect an 8082 My IC Phone set to the LAN (Local Area Network)
- Connect the external power adapter, if necessary
Connecting an 8082 My IC Phone set to the LAN
To connect the set to the LAN:
- If using the 8082 Power Over Ethernet Injector Kit:
a. Plug an RJ45 cable between the data in port of the kit and the LAN
b. Plug an RJ45 cable between the data and power out port of the kit and the set LAN
connector
c. Plug the kit to the mains
- If not using the 8082 Power Over Ethernet Injector Kit, plug an RJ45 cable between the set
LAN connector and a port of the switch

4-36              

Downloaded from www.Manualslib.com manuals search engine

     &' (

Connecting power supply

If not using a PoE switch or the 8082 Power Over Ethernet Injector Kit, connect the AC/DC
external adapter:
1. Plug the appropriate cable from the adapter into the set's power supply connector.
2. Connect the plug from the adapter to the mains power supply.
Initializing the sets
The following paragraphs describe how to:
- Select the initialization type
- Initialize the 8082 My IC Phone set
Selecting the initialization type
The default initialization is dynamic.
To select the initialization type, refer to the following table.
table 4.16: Initialization type selection
If Then the required Further information
initialization type is
You have a DHCP Dynamic or Proprietary - Refer to Configuring the DHCP server
server dynamic for dynamic initialization
- In case of Proprietary dynamic
selection, the IP address of the set must
be provided by the Proprietary router.
You do not have a Static - Refer to Configuring network parameters
DHCP server for static initialization
- Obtain from your network administrator:
• An IP address for the 8082 My IC
Phone set
• The subnetwork mask
• The router address
• The DNS addresses (primary and
secondary)
• The VLAN ID (if VLAN is used)
• The URL of the Alcatel-Lucent
OmniPCX Office Communication
Server for set configuration file
download
Note:
You need to know the set directory number.

Configuring the DHCP server for dynamic initialization

Two types of dynamic initialization are available:
- Dynamic (default value): the set selects in priority DHCP offers, with a Vendor Specific
option corresponding to an Alcatel-Lucent server.
- Dynamic Alcatel: the set accepts only DHCP offers with a Vendor Specific option

              4-37

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

corresponding to an Alcatel-Lucent Enterprise server (alcatel.int-ip.0,

alcatel.a4400.0, alcatel.a4200.0).
When initializing in dynamic mode, the set provides the following information in the DHCP
Discover message
- Option 60: (vendor class identifier): alcatel.ictouch.0
- Option 55: list of requested options: subnet mask, router option, broadcast address, option
43 vendor specific info, server ID, renewal time, rebinding time and vendor class ID
Option 43 is vendor specific information, meaning that this option is defined for a specific client
vendor ID. In the DHCP offer, the data within Option 43 corresponds to the client vendor ID
specified in the request.
In the case of 8082 My IC Phone sets, suboption 67 of option 43 provides the path of
configuration files on the Alcatel-Lucent OmniPCX Office Communication Server.
The DHCP offer provides the following parameters:
- IP address
- Router IP address
- Subnet mask
- Option 66: IP address or name of the Alcatel-Lucent OmniPCX Office Communication
Server, for example 192.168.12.34
- Suboption 67 of option 43: the value of this sub-option corresponds to the DM Url.It must
contain a string value set to /dmcfg/
- Option 58: VLAN ID: this is sent as a suboption of option 43
Optionally, the DHCP offer can include the following parameters, which can also be configured
locally on the terminal or on the Alcatel-Lucent OmniPCX Office Communication Server:
- Option 6: Domain Name Server (DNS primary and secondary)
- Option 15: Domain name
- Option 12: Host name (eg, ICTouch<MAC>)
- Option 42: SNTP server
- Option 120: SIP server (outbound proxy server address or name)
Configuring network parameters for static initialization
MMI allows to access and configure the following parameters (you must have administration
rights to modify static configuration):
- In the Network menu:
• DM (Alcatel-Lucent OmniPCX Office Communication Server) URL: https://OmniPCX
Office IP address/dmcfg/
• DNS addresses
• Ethernet parameters: the LAN and PC Ethernet interfaces are by default configured in
auto-negotiation mode
• IP parameters
• Log parameters, allowing to define a syslog server for log reception
• Network parameters, allowing to:
• Enable and configure a DHCP User Class: this makes the set send the standard

4-38              

Downloaded from www.Manualslib.com manuals search engine

     &' (

DHCP option 77 (User Class, RFC2132) within the DISCOVER and REQUEST
DHCP messages. Using this option allows to define groups of terminals, and to
attach these groups to different and independent Com Servers.
• Define an SNTP Server address and refresh period
• Proxy host and port
• SIP parameters (read only)
- In Security menu:
• 802.1x parameters
• Certificates: not used
Configuring the user name and password in OMC
To modify the name and reset the password:
- In OMC, go to Users/Base stations List.
- Click the user in the list, modify her/his name in the corresponding field and click Modify.
- In the SIP Parameters tab, click the SIP password reset button to get a new password (In
OMC, only reset of user password can be done, user password can be set only in 8082 My
IC Phone set).
Connecting optional equipment
Headsets
A headset can be used with 8082 My IC Phone sets.
By default the set is configured to detect headset connection. When the headset is plugged in,
the audio is sent to the headset. The hands-free key allows you to switch from handset to
headset.
A Bluetooth® headset may be used.
If your headset is wired, plug it to the associated set connector (see: figure: 8082 My IC Phone
set connectors ), which can be any of the following:
- The jack plug
- The set USB port
External station speakers
Any connector used for a headset can be used for external speakers.
Customize your set to take the external station speaker into account:
1. Touch the Settings button
Note:
According to system administration, this button may not appear. The availability of this option is
determined by the set configuration files. Contact your telephony and/or system administrator.
2. Select Devices < Audio
3. Select the connection of your choice (from Accessory device to Bluetooth device)
4. Touch the field to access available values
5. Select Loudspeaker

              4-39

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

6. If your device is not Bluetooth, plug it to the corresponding connector

Traffic priority on the internal switch
The 8082 My IC Phone set includes an internal LAN switch.
This switch allows to connect a PC.
The internal switch has three ports:
- A LAN port
- An internal port
- A PC port, to connect a PC to the LAN.
The internal switch privileges VoIP traffic over PC port traffic.
This switch has two waiting queues:
- The HPQ (High Priority Queue) to proceed all packets from the terminal
- The LPQ (Low Priority Queue) to proceed packets from the PC port
The switch proceeds seven HPQ packets for an LPQ packet.
Exception: packets from the PC port use the HPQ when they are tagged with a DSCP or
802.1p priority and when the priority value is superior or equal to 4.
4.4.1.1.3 Upgrading the software
The Alcatel-Lucent OmniTouch™ 8082 My IC Phone set software is upgraded during
OmniPCX Office software upgrade. Ensure the 8082 My IC Phone option is validated in the
OMC-Software Download window: refer to module System Startup from OMC - Downloading
the Software

4.4.2 4135 IP Conference Phone

4.4.2.1 Commissioning
4.4.2.1.1 Overview
This module presents all the actions required for commissioning 4135 IP Conference Phone
sets.

4-40              

Downloaded from www.Manualslib.com manuals search engine

     &' (

Figure 4.42: 4135 IP Conference Phone set layout

The following figure illustrates the connectors on the base of each set.

              4-41

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

Figure 4.43: 4135 IP Conference Phone set connectors

The 4135 IP Conference Phone is a SIP device which has no handset; it is dedicated to be
used as central for conferences.
Conferences are not managed by the system, but by the device itself. Up to four 4135 IP
Conference Phones can be connected to the Alcatel-Lucent OmniPCX Office Communication
Server.
4.4.2.1.2 Commissioning the set
This section describes how to commission the set in the two available commissioning types:
- Static: commissioning is manual on the set and on OMC
- Dynamic (DHCP): the set automatically retrieves its IP address and other parameters from
a DHCP server. Complementary operations are necessary on the set and on OMC
For static commissioning, operations are:
1. Configure the user in OMC, refer to Configuring the user by OMC
2. Connect the set to the LAN, refer to Connecting the set to the LAN
3. Configure the network parameters on the set, refer to Configuring network parameters for
static initialization
4. Export the server certificate from the Alcatel-Lucent OmniPCX Office Communication
Server: refer to Exporting the server certificate from the Alcatel-Lucent OmniPCX Office
Communication Server
5. Upload the certificate on the 4135 IP Conference Phone
For dynamic commissioning, operations are:
1. Configure the DHCP Server, refer to Configuring the DHCP server for dynamic initialization
2. Connect the set to the LAN, refer to Connecting the set to the LAN
3. Configure the user name and password and consult the SIP password in OMC, refer to
Configuring the user name and password in OMC
4. Export the server certificate from the Alcatel-Lucent OmniPCX Office Communication
Server: refer to Exporting the server certificate from the Alcatel-Lucent OmniPCX Office
Communication Server
5. Enter the SIP password through MMI, refer to Entering the SIP password through local
MMI
6. Upload the certificate on the 4135 IP Conference Phone
Prerequisites
- The Alcatel-Lucent OmniPCX Office Communication Server must be R810 or higher and
must be operational
- For network configuration, any of the following must be implemented:
• In dynamic mode, a DHCP server must be configured
• In static mode, a free IP address must be available for the set
- A port with PoE must be available on a switch
Configuring the user by OMC

4-42              

Downloaded from www.Manualslib.com manuals search engine

     &' (

This paragraph applies to OMC configuration of sets initializing in static mode. In dynamic
(DHCP) mode, the following operation is not mandatory but the server certificate must be
exported from the Alcatel-Lucent OmniPCX Office Communication Server to the PC and can
then be uploaded to the 4135 IP Conference Phone.
To create a 4135 IP Conference Phone:
1. In OMC, go to Users/Base stations List.
2. Select a No., IP access, enter a name and click the Add button.
3. Select IP terminal and click OK.
4. Select the newly created user in the list and select 4135 IP Conference Phone in the
combo box type.
5. Click the Modify button.
6. Click the newly created user to open the User dialog box.
7. Click the IP/SIP button and enter the MAC adress of the set in the IP Parameters tab.
8. If needed, in the SIP Parameters, click the SIP password reset button to get a new
password.
Connecting the set to the LAN

Note:
the set is supplied via Ethernet, so make sure using a 802.3af standard-compatible switch.
To connect the set to the LAN:
1. Turn the set over so that you can see its base.
2. Plug the RJ45 cable into the set's LAN connector.
3. Connect the RJ45 cable to the LAN.
Initializing the sets
This section describes how to:
- Select the initialization mode
- Initialize the 4135 IP Conference Phone set
Selecting the initialization type
The default initialization is dynamic.
To select the initialization type, refer to the table below.
table 4.17: Initialization type selection
If Then the required Further information
initialization mode is
You have a DHCP Dynamic or Proprietary - Refer to Configuring the DHCP server
server dynamic for dynamic initialization
- In the case of Proprietary dynamic
mode, the IP address of the set must be
provided by the Proprietary router.

              4-43

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

You do not have a Static - Refer to Configuring network parameters

DHCP server for static initialization
- Obtain from your network administrator:
• An IP address for the 4135 IP
Conference Phone set
• The subnetwork mask
• The router address
• The DNS addresses (primary ans
secondary)
• The VLAN ID (if VLAN is used)
• The URL of the Alcatel-Lucent
OmniPCX Office Communication
Server for configuration files
download
Note:
You need to know the set directory number.

Configuring the DHCP server for dynamic initialization

In Dynamic initialization (default value), the set selects the first DHCP offer, with a Vendor
Specific option corresponding to an Alcatel-Lucent server.
When initializing in dynamic mode, the set provides the following information in the DHCP
Discover message:
- Option 60: (vendor class identifier): alcatel.sip.0
- Option 55: list of requested options: subnet mask, router option, broadcast address, option
43 vendor specific info, server ID, renewal time, rebinding time and vendor class ID
Option 43 is vendor specific information, meaning that this option is defined for a specific client
vendor ID. In the DHCP offer, the data within Option 43 corresponds to the client vendor ID
specified in the request.
In the case of 4135 IP Conference Phone sets, suboption 67 of option 43 provides the path of
configuration files on the Alcatel-Lucent OmniPCX Office Communication Server.
The DHCP offer provides the following parameters:
- IP address
- Router IP address
- Subnet mask
- Option 66: IP address or name of the Alcatel-Lucent OmniPCX Office Communication
Server, for example 192.168.12.34
- Suboption 67 of option 43: the value of this sub-option must contain a string value set to
https://alize/dmcfg/
- Option 58: VLAN ID: this is sent as a suboption of option 43
Optionally, the DHCP offer can include the following parameters, which can also be configured
locally on the terminal or on the Alcatel-Lucent OmniPCX Office Communication Server:
- Option 6: Domain Name Server (DNS primary and secondary)
- Option 15: Domain name
- Option 12: Host name (eg, ICTouch<MAC>)

4-44              

Downloaded from www.Manualslib.com manuals search engine

     &' (

- Option 42: SNTP server

- Option 120: SIP server (outbound proxy server address or name)
Exporting the server certificate from the Alcatel-Lucent OmniPCX Office
Communication Server
1. Go to OMC->Tools->Import/Export->Export Server Certificate.
The Export Server Certificate window is displayed
2. Click Browse button.
The Exportfile window is displayed:
• The File name field indicates server.crt. The file name can be modified as needed
• The Files of type field indicates Certificate Files
3. Specify the destination path for the export and click OK: The selected path and the
certificate file name are displayed in the Export Server Certificate window
4. Click the Export button: The certificate file is exported from the Alcatel-Lucent OmniPCX
Office Communication Server to the specified file path in PC
5. Click the Return button
Configuring network parameters for static initialization
The following parameters must be entered through the MMI:
- IP address
- Subnet mask
- Gateway address
- DNS addresses
- VLAN use
- VLAN ID (if VLAN use is set)
- URL: provides the URL on the Alcatel-Lucent OmniPCX Office Communication Server to
download configuration file. The path on the Alcatel-Lucent OmniPCX Office
Communication Server is /dmcfg/
- SIP password
Configuring the user name and password in OMC
To modify the name and password:
- In OMC, go to Users/Base stations List.
- Click the user in the list.
- Modify the user name in the corresponding field and click Modify.
- Double-click the user in the list to open the User dialog box.
- Click on IP/SIP, go to SIP parameters Tab to consult the SIP password.
Entering the SIP password through local MMI
For static and dynamic initialization, enter the SIP password through MMI.
4.4.2.1.3 Upgrading the software

              4-45

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

The 4135 IP Conference Phone set software is automatically upgraded during OmniPCX
Office software upgrade (there is no specific option to select in the OMC-Software Download
window: refer to module System Startup from OMC - Downloading the Software )
The 4135 IP Conference Phone set software can also be upgraded manually through the MMI.

4.4.3 Generic SIP Phones

4.4.3.1 Commissioning
4.4.3.1.1 Overview
This module presents all the actions required for commissioning generic SIP sets.
The List of supported SIP Phones is available on the Alcatel-Lucent Applications Partner
Program (AAPP) web site.
4.4.3.1.2 Commissioning Generic SIP Sets
This section describes how to commission a generic SIP Set.
The following operations must be performed:
1. Configure the user in OMC, refer to Configuring the User in OMC
2. Connect the set, refer to Connecting the Set and switch it on
3. Configure the generic SIP set, refer to Configuring the generic SIP set
Prerequisites
- The Alcatel-Lucent OmniPCX Office Communication Server must be R810 or higher and
must be operational
- A free IP address must be available for the set
- A port with PoE must be available on a switch
Configuring the User in OMC
To create a generic SIP set:
1. In OMC, go to Users/Base stations List.
2. Select a No., IP access and click on the Add button.
3. Select IP terminal and enter a Name.
4. Select the newly created user in the list and select Basic SIP Phone or Open SIP Phone
in the combo box.
See the different features relating to basic or open SIP modes: module List of Services
Provided - Services provided - Services Offered on SIP Sets
5. Click the Modify button.
6. Click the Details button. The User window is opened.
7. Click the IP/SIP button. The IP/SIP parameters window is opened.
8. In the SIP parameters tab, click the SIP password reset button. A new password is
generated in the SIP password field.

4-46              

Downloaded from www.Manualslib.com manuals search engine

     &' (

9. A virtual MAC Address is automatically generated but it can be replaced by the real MAC
Address of the SIP device.
Note:
The MAC Address must be unique and is used to identify the subscriber in the OmniPCX Office call
handling (SIP password is used for authentication).
10. Note this new password safely. It will be requested during the generic SIP set configuration
( Configuring the generic SIP set ).
Connecting the Set
This section describes how to:
- Connect a generic SIP set to the LAN (Local Area Network)
- Connect the power supply
Prerequisites
None
Connecting a SIP set to the LAN

Note:
If the set is supplied via Ethernet, ensure you are using a 802.3af standard-compatible switch.
To connect the set to the LAN:
- Plug the RJ45 cable into the set's LAN connector.
- Connect the RJ45 cable to the LAN.
Connecting Power Supply (Optional)
To supply power via an AC/DC external adapter:
- Plug the appropriate cable from the adapter into the set's power supply connector.
- Connect the plug from the adapter to the mains power supply.
Configuring the generic SIP set
The following parameters must be entered through the MMI or web interface when available:
- IP address (if no DHCP server is configured)
- Subnet mask (if no DHCP server is configured)
- Gateway adress (if no DHCP server is configured)
- DNS adresses (if no DHCP server is configured)
- VLAN use (if no DHCP server is configured)
- VLAN ID if VLAN use is set (if no DHCP server is configured)
- SIP username
- SIP password: this is different from the user password. It is randomly generated for each
SIP phone by the system and must be provided to the user in a secured way. It is used
both for SIP registration and for SIP authentication, since every SIP message must be
authenticated.

              4-47

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

Note:
The random password must be entered manually in MMI. It must be made of with letters and
numbers only and can be viewed/reset in OMC.
This password has been previously generated in: Configuring the User in OMC .
- Registrar and proxy IP addresses: the Alcatel-Lucent OmniPCX Office Communication
Server IP address and the SIP port must be set to value 5059
- Authentication Realm: Alcatel-Lucent OmniPCX Office Communication Server IP
address by default
- Registration interval: value greater than 120 seconds
- Transport protocol: the UDP protocol is preferred, TCP is used if the SIP packet length is
greater than the MTU value or if the remote SIP endpoint requests the TCP protocol
- Domain name: Alcatel-Lucent OmniPCX Office Communication Server IP address by
default

4.5 8 Series Sets

4.5.1 IP Touch 4008/4018 Phone

4.5.1.1 Commissioning
4.5.1.1.1 Overview
This module presents all the actions required for commissioning:
- The Alcatel-Lucent IP Touch 4018 Phone set
- The Alcatel-Lucent IP Touch 4018 phone Extended Edition set
The commissioning of Alcatel-Lucent IP Touch 4018 Phone and Alcatel-Lucent IP Touch 4018
phone Extended Edition sets is identical.
The following figure illustrates the connectors on the base of the Alcatel-Lucent IP Touch
4018 Phone and Alcatel-Lucent IP Touch 4018 phone Extended Edition sets.

4-48              

Downloaded from www.Manualslib.com manuals search engine

     &' (

Figure 4.44: Alcatel-Lucent IP Touch 4018 Phone and Alcatel-Lucent IP Touch 4018 phone
Extended Edition connectors

4.5.1.1.2 Commissioning the set

This section describes how to:
- Connect the set
- Initialize the set
- Program keys
Prerequisites
None.
Connecting the sets
This section describes how to:
- Connect an IP Touch set to the LAN (Local Area Network)
- Connect the power supply
Prerequisites
None.
Connecting an IP Touch set to the LAN
To connect the set to the LAN:

              4-49

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

1. Turn the set over so that you can see its base.
2. Plug the RJ45 cable into the set's LAN connector.
3. Connect the RJ45 cable to the LAN itself.
Connecting power supply
The set can be supplied from two possible power sources:
- An AC/DC external adapter which is a 42V power supply
A female jack is used to connect the power adapter. The AC/DC external adapter is the
same for IP Touch and e-Reflex sets.
- Power over Ethernet (PoE)
The supply via Ethernet can be implemented using a 802.3af standard-compatible switch.
To supply power via an AC/DC external adapter:
1. Plug the appropriate cable from the adapter into the set's power supply connector.
2. Connect the plug from the adapter to the mains power supply.
Initialization starts.
Initializing the sets
This section describes how to:
- Choose the initialization mode
- Initialize the IP Touch set
Prerequisites
The IP Touch set must be connected to the:
- LAN
- Power supply
Choosing the initialization mode
The default mode is dynamic mode.
To choose the initialization mode, refer to the table below.
table 4.18: Initialization modes
If Then the required And
initialization mode is
You have a DHCP server Dynamic mode or Refer to table: Initialization
Proprietary dynamic mode procedure
In the case of Proprietary
dynamic mode, the IP address
of the set must be provided by
the Proprietary router.

4-50              

Downloaded from www.Manualslib.com manuals search engine

     &' (

You do not have a DHCP Static mode - Refer to table: Initialization

server procedure
- Obtain from your network
administrator:
• An IP address for the
IP Touch set
• The subnetwork mask
• The router address
• The TFTP server
address, which is the
IP address of the
PowerCPU board
embedding the VoIP
board

Initializing the IP Touch set

To initialize the IP Touch set, refer to the table below.
Note 1:
In each of the two cases below, you can view the IP Touch set's software version after Step 2 by
selecting Version in the Main menu.
table 4.19: Initialization procedure
For an Procedure
initialization
that is
Dynamic mode 1. Connect the power supply.
or Proprietary 2. After initialization phase 2 is completed and before phase 5 starts, press i, then
dynamic mode the # key.
The Main menu appears.
3. If the set was previously in static mode, choose IP Parameters from the Main
menu.
The IP Parameters menu appears.
4. Choose Dynamic and press the OK key.
5. Save by pressing the # key.
6. Exit the Main menu by pressing the * key.

              4-51

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

Static 1. Connect the power supply.

2. Before initialization phase 5 starts, press i, then the # key.
The Main menu appears.
3. From the Main menu, choose IP Parameters.
The IP Parameters menu appears.
4. Choose Static and press the OK key.
5. Enter the following:
a. IP address
b. Subnetwork mask
c. Router address
d. TFTP server address
e. TFTP port (69)
f. CPU address
6. Enter the required VLAN details, as follows:
a. If required, select Use VLAN and then enter the VLAN ID number.
b. Ensure that Strict VLAN is set as required. It is selected by default;
de-selecting it allows you to use a DHCP server in another VLAN.
7. Save the above parameter values by pressing the # key.
8. Exit the Main menu by pressing the * key.
The set restarts from phase 1 with the new parameters.
Note 2:
If an error message appears during initialization, disconnect the power adapter, then plug it in
again, so that the system restarts initialization.

Restarting initialization
If you want to change a parameter value, restart initialization, as detailed below.
To restart initialization:
1. Disconnect the IP Touch set from the power supply.
2. Reconnect the power supply.
3. Execute the initialization procedure as detailed in table: Initialization procedure
Programming keys
This section describes how to program the programmable keys.
In fact, only the direct call key can be programmed (with a telephone number), which by
default is the sixth programmable key. However, the Personal/Dial by name key can be
programmed in a similar way.
To program a key:
1. Press the i key followed by the required programmable key.
2. Press one key of the 2-way navigator (up or down).
3. Enter the telephone number to be associated with this programmable key.
4. Press OK. The set then goes back to its default display.
Relocating and retaining IP Touch sets
This section describes how to relocate and retain the same set.

4-52              

Downloaded from www.Manualslib.com manuals search engine

     &' (

In the procedure below, it is assumed that:

- there is one DHCP server
- no VLAN has to be configured.
Prerequisites
None.
Relocating and retaining the same set
To relocate and retain the same set:
1. Unplug the set.
2. Plug the set into a connector at its new location.
4.5.1.1.3 The Alcatel-Lucent IP Touch 4008 Phone set
The Alcatel-Lucent IP Touch 4008 Phone is a cost reduction of the Alcatel-Lucent IP Touch
4018 Phone with a new transceiver and a new LAN switch.
The Alcatel-Lucent IP Touch 4008 Phone configuration is the same as the Alcatel-Lucent IP
Touch 4018 Phone configuration: both sets share the same profile.
The Alcatel-Lucent IP Touch 4008 phone Extended Edition configuration is the same as the
Alcatel-Lucent IP Touch 4018 Phone configuration.

4.5.2 IP Touch 4028/4038/4068 Phone

4.5.2.1 Commissioning
4.5.2.1.1 Overview
This module presents all the actions required for commissioning: .
- The Alcatel-Lucent 8 series:
• Alcatel-Lucent IP Touch 4028 Phone
• Alcatel-Lucent IP Touch 4038 Phone
• Alcatel-Lucent IP Touch 4068 Phone
- The Alcatel-Lucent IP Touch 8 series phone Extended Edition:
• Alcatel-Lucent IP Touch 4028 phone Extended Edition
• Alcatel-Lucent IP Touch 4038 phone Extended Edition
• Alcatel-Lucent IP Touch 4068 phone Extended Edition
The commissioning of Alcatel-Lucent 8 series and Alcatel-Lucent IP Touch 8 series phone
Extended Edition is the same.
In the following sections, when Alcatel-Lucent IP Touch 4028 Phone, Alcatel-Lucent IP Touch
4038 Phone and Alcatel-Lucent IP Touch 4068 Phone are mentioned, they refer to the two
ranges of sets (Alcatel-Lucent 8 series and Alcatel-Lucent IP Touch 8 series phone Extended
Edition), unless specifically indicated.
The following figure illustrates the connectors on the base of each set.

              4-53

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

Figure 4.45: Alcatel-Lucent IP Touch 4028 Phone, Alcatel-Lucent IP Touch 4038 Phone and
Alcatel-Lucent IP Touch 4068 Phone connectors

4.5.2.1.2 Commissioning the sets

This section describes how to:
- Connect the sets
- Initialize the sets
- Connect optional equipment
- Program keys
Prerequisites
None.
Connecting the sets
This section describes how to:
- Connect an IP Touch set to the LAN (Local Area Network)
- Connect the power supply
Prerequisites
None.
Connecting an IP Touch set to the LAN

4-54              

Downloaded from www.Manualslib.com manuals search engine

     &' (

To connect the set to the LAN:

1. Turn the set over so that you can see its base.
2. Plug the RJ45 cable into the set's LAN connector.
3. Connect the RJ45 cable to the LAN itself.
Connecting power supply
The set can be supplied from two possible power sources:
- An AC/DC external adapter which is a 42V power supply
A female jack is used to connect the power adapter. The AC/DC external adapter is the
same for IP Touch and e-Reflex sets.
- Power over Ethernet (PoE)
The supply via Ethernet can be implemented using a 802.3af standard-compatible switch.
To supply power via an AC/DC external adapter:
1. Plug the appropriate cable from the adapter into the set's power supply connector.
2. Connect the plug from the adapter to the mains power supply.
Initialization starts.
Initializing the sets
This section describes how to:
- Choose the initialization mode
- Initialize the IP Touch set
Prerequisites
The IP Touch set must be connected to the:
- LAN
- Power supply
Choosing the initialization mode
The default mode is dynamic mode.
To choose the initialization mode, refer to the table below.
table 4.20: Initialization modes
If Then the required And
initialization mode is
You have a DHCP server Dynamic mode or Refer to table: Initialization
Proprietary dynamic mode procedure
In the case of Proprietary
dynamic mode, the IP address
of the set must be provided by
the Proprietary router.

              4-55

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

You do not have a DHCP Static mode - Refer to table: Initialization

server procedure
- Obtain from your network
administrator:
• An IP address for the
IP Touch set
• The subnetwork mask
• The router address
• The TFTP server
address, which is the
IP address of the
PowerCPU board
embedding the VoIP
board
Note:
You need to know your set's
directory number.

Initializing the IP Touch set

To initialize the IP Touch set, refer to the table below.
table 4.21: Initialization procedure
For an Procedure
initialization
that is
Dynamic mode 1. Connect the power supply.
or Proprietary 2. Before initialization phase 5 starts, press i, then the # key.
dynamic mode The Main menu appears.
3. If the set was previously in static mode, choose IP Parameters from the Main
menu.
The IP Parameters menu appears.
4. Choose Dynamic.
5. Save by pressing the soft key in the upper left part of the display.
6. Exit the Main menu by pressing the soft key in the upper right part of the display.

4-56              

Downloaded from www.Manualslib.com manuals search engine

     &' (

Static 1. Connect the power supply.

2. Before initialization phase 5 starts, press i, then the # key.
The Main menu appears.
3. From the Main menu, choose IP Parameters.
The IP Parameters menu appears.
4. Choose Static.
5. Enter the following:
a. IP address
b. Subnetwork mask
c. Router address
d. TFTP server address
e. TFTP port (69)
f. CPU address
6. Enter the required VLAN details, as follows:
a. If required, select Use VLAN and then enter the VLAN ID number.
b. Ensure that Strict VLAN is set as required. It is selected by default;
de-selecting it allows you to use a DHCP server in another VLAN.
7. Save by pressing the soft key in the upper left part of the display.
8. Exit the Main menu by pressing the soft key in the upper right part of the display.
The set restarts from phase 1 with the new parameters.
Note:
If an error message appears during initialization, disconnect the power adapter, then plug it in
again, so that the system restarts initialization.

Restarting initialization
If you want to change a parameter value, restart initialization, as detailed below.
To restart initialization:
1. Disconnect the IP Touch set from the power supply.
2. Reconnect the power supply.
3. Execute the initialization procedure as detailed in table: Initialization procedure
Connecting optional equipment
This section describes how to:
- Connect an Add-On module (AOM) to the sets
- Connect a headset
- Connect an external station speaker
Connecting an Add-On module to the sets
Add-On Modules (AOMs) can be connected to the Alcatel-Lucent IP Touch 4028 Phone,
Alcatel-Lucent IP Touch 4038 Phone and Alcatel-Lucent IP Touch 4068 Phone sets. They are
added to the right side of the set.
Three types of Add-On Module exist and provide keys associated with icons:
- AOM10 provides 10 keys
- AOM40 provides 40 keys

              4-57

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

- AOM Alcatel-Lucent 8 series and Alcatel-Lucent 9 series Smart Display Module provides
14 keys with programmable LCD labels
Prerequisites
None.
Rules and restrictions
The following rules apply to the use of Add-On Modules with the Alcatel-Lucent IP Touch
4028 Phone, Alcatel-Lucent IP Touch 4038 Phone and Alcatel-Lucent IP Touch 4068 Phone
sets:
- A maximum of three Add-On Modules of the types AOM10 and AOM40 can be connected
to each set, providing up to 120 additional keys.
- A maximum of three Smart Display Modules can be connected to each set, providing up to
42 additional keys.
- Add-On Modules of types AOM10 and AOM40 can be used on the same set, but a Smart
Display Module cannot be used in conjunction with an AOM10 or AOM40.
- If an AOM10 is used with other Add-On Modules, it must be connected as the last module
on the far right of the set.
Connecting Add-On Modules
To connect an Add-On Module:
1. Remove the tab located on the right side of the IP Touch set.
2. Plug the Add-On Module's RJ45 connector into the set's RJ45 connector.
3. Insert the Add-On Module attachments into the appropriate holes located on the right side
of the IP Touch set.
4. Screw the Add-On Module to the IP Touch set.
Note:
If the IP Touch set is on when you plug in an Add-On Module, you must restart the set after connection.

Connecting headsets
The headset jack is located on the left side of the set.
The 3.5 mm female jack can receive a headset jack.
The hands-free key allows you to switch from handset to headset.
Prerequisites
None.
Connecting a headset
To connect a headset, simply plug the headset jack into the associated connector on the side
of the set.
Connecting external station speakers
The external station speaker jack is located on the left side of the IP Touch set.

4-58              

Downloaded from www.Manualslib.com manuals search engine

     &' (

The 3.5 mm female jack can receive an external station speaker jack.
In order to take the external station speaker into account, the set customization for the jack
has to be set to “Loudspeaker”.
Prerequisites
None.
Connecting an external station speaker
To connect an external station speaker, plug the external station speaker jack into the
associated connector on the side of the set.
Programming keys
This section describes how to program a programmable key from the:
- F1/F2 keys
- Add-On Module keys (if any)
- virtual add-on keys
Two methods are presented.
Programming a key
To program a key:
1. From the MENU tab, select Settings.
The Settings menu appears.
2. From the Settings menu, select Keys.
The virtual add-on keys appear.
3. Select the key to be programmed, as follows:
• To program a virtual add-on key, scroll using the up/down navigator keys until you
reach the required virtual key and then press the corresponding soft key.
• To program the F1 or F2 key, or a key on a connected Add-On Module, simply press
this key.
4. Select Name and enter the name to be associated with the selected key, then press OK.
The desired name is associated with the key.
5. Select Number and enter the telephone number to be associated with the key, then press
OK.
The desired number is associated with the key.
6. Press Exit to go back to home page.
Programming a key (fast customization)
You can also program a key using the following method:
1. Select the key to be programmed, as follows:
• To program a virtual add-on key, from the PERSO tab press i followed by the required
key.
• To program the F1 or F2 key, or a key on a connected Add-On Module, from any tab
press i followed by the required key.

              4-59

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

2. Select Name and enter the name to be associated with the selected key, then press OK.
The desired name is associated with the key.
3. Select Number and enter the telephone number to be associated with the key, then press
OK.
The desired number is associated with the key.
4. Press Exit to go back to the home page.
Relocating and retaining IP Touch sets
This section describes how to relocate and retain the same set.
In the procedure below, it is assumed that:
- there is one DHCP server
- no VLAN has to be configured.
Prerequisites
None.
Relocating and retaining the same set
To relocate and retain the same set:
1. Unplug the set.
2. Plug the set into a connector at its new location.

4.6 9 Series Sets

4.6.1 4019 Digital Phone

4.6.1.1 Commissioning
4.6.1.1.1 Overview
This module presents all the actions required for commissioning the Alcatel-Lucent 4019
Digital Phone set.
The following figure illustrates the connectors on the base of the set.

4-60              

Downloaded from www.Manualslib.com manuals search engine

     &' (

Figure 4.46: Alcatel-Lucent 4019 Digital Phone connectors

4.6.1.1.2 Commissioning the set

This section describes how to:
- Connect the set
- Program keys
Prerequisites
None.
Connecting the set
This section describes how to connect the set to the telephone system.
Prerequisites
None.
Connecting the set to the telephone system
To connect the set to the telephone system:
1. Turn the set over so that you can see its base.
2. Plug the RJ11 cable into the set's UA port/phone line connector.
3. Connect the RJ11 cable to a UA port in the telephone system.
Programming keys
This section describes how to program the programmable keys.

              4-61

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

In fact, only the direct call key can be programmed (with a telephone number), which by
default is the sixth programmable key. However, the Personal/Dial by name key can be
programmed in a similar way.
To program a key:
1. Press the i key followed by the required programmable key.
2. Press one key of the 2-way navigator (up or down).
3. Enter the telephone number to be associated with this programmable key.
4. Press OK. The set then goes back to its default display.

4.6.2 4029/4039 Digital Phone

4.6.2.1 Commissioning
4.6.2.1.1 Overview
This module presents all the actions required for commissioning the Alcatel-Lucent 4029
Digital Phone and Alcatel-Lucent 4039 Digital Phone sets.
The following figure illustrates the connectors on the base of each set.

Figure 4.47: Alcatel-Lucent 4029 Digital Phone and Alcatel-Lucent 4039 Digital Phone
connectors

4.6.2.1.2 Commissioning the sets

This section describes how to:
- Connect the sets

4-62              

Downloaded from www.Manualslib.com manuals search engine

     &' (

- Connect optional equipment

- Program keys
Prerequisites
None.
Connecting the sets
This section describes how to connect a set to the telephone system.
Prerequisites
None.
Connecting to the telephone system
To connect a set to the telephone system:
1. Turn the set over so that you can see its base.
2. Plug the RJ11 cable into the set's UA port/phone line connector.
3. Connect the RJ11 cable to a UA port in the telephone system.
Connecting optional equipment
This section describes how to:
- Connect an Add-On module (AOM) to the sets
- Connect a headset
- Connect an external hands-free device
Connecting an Add-On module to the sets
Add-On Modules (AOMs) can be connected to the Alcatel-Lucent 4029 Digital Phone and
Alcatel-Lucent 4039 Digital Phone sets. They are added to the right side of the set.
Three types of Add-On Module exist and provide keys associated with icons:
- AOM10 provides 10 keys
- AOM40 provides 40 keys
- AOM Alcatel-Lucent 8 series and Alcatel-Lucent 9 series Smart Display Module provides
14 keys with programmable LCD labels
Prerequisites
None.
Rules and restrictions
The following rules apply to the use of Add-On Modules with the Alcatel-Lucent 4029
Digital Phone and Alcatel-Lucent 4039 Digital Phone sets:
- A maximum of three Add-On Modules of the types AOM10 and AOM40 can be connected
to each set, providing up to 120 additional keys.
- A maximum of three Smart Display Modules can be connected to each set, providing up to

              4-63

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

42 additional keys.
- Add-On Modules of types AOM10 and AOM40 can be used on the same set, but a Smart
Display Module cannot be used in conjunction with an AOM10 or AOM40.
- If an AOM10 is used with other Add-On Modules, it must be connected as the last module
on the far right of the set.
Connecting Add-On Modules
To connect an Add-On Module:
1. Remove the tab located on the right side of the set.
2. Plug the Add-On Module's RJ45 connector into the set's RJ45 connector.
3. Insert the Add-On Module attachments into the appropriate holes located on the right side
of the set.
4. Screw the Add-On Module to the set.
Note:
If the set is on when you plug in an Add-On Module, you must restart the set after connection.

Connecting headsets
The headset jack is located on the left side of the set.
The 3.5 mm female jack can receive a headset jack.
The hands-free key allows you to switch from handset to headset.
Prerequisites
None.
Connecting a headset
To connect a headset, simply plug the headset jack into the associated connector on the side
of the set.
Connecting an external hands-free device
The external device jack is located on the left side of the set.
The 3.5 mm female jack can receive the jack of an external hands-free device.
In order to take the external hands-free device into account, the set's customization for the jack
must be set to “Handsfree”.
Prerequisites
None.
Connecting an external hands-free device
To connect an external hands-free device, plug the external device's jack into the associated
connector on the side of the set.
Programming keys
This section describes how to program a programmable key from the:

4-64              

Downloaded from www.Manualslib.com manuals search engine

     &' (

- F1/F2 keys
- Add-On Module keys (if any)
- virtual add-on keys
Two methods are presented.
Programming a key
To program a key:
1. From the MENU tab, select Settings.
The Settings menu appears.
2. From the Settings menu, select Keys.
The virtual add-on keys appear.
3. Select the key to be programmed, as follows:
• To program a virtual add-on key, scroll using the up/down navigator keys until you
reach the required virtual key and then press the corresponding soft key.
• To program the F1 or F2 key, or a key on a connected Add-On Module, simply press
this key.
4. Select Name and enter the name to be associated with the selected key, then press OK.
The desired name is associated with the key.
Note:
As of release 6.0 of Alcatel-Lucent OmniPCX Office Communication Server, it is possible to use
Unicode - Chinese and Cyrillic - characters. It is at this step that it becomes active, if used. For more
information about IME, refer to the section Operation - Input Method Editor in this chapter.
5. Select Number and enter the telephone number to be associated with the key, then press
OK.
The desired number is associated with the key.
6. Press Exit to go back to home page.
Programming a key (fast customization)
You can also program a key using the following method:
1. Select the key to be programmed, as follows:
• To program a virtual add-on key, from the PERSO tab press i followed by the required
key.
• To program the F1 or F2 key, or a key on a connected Add-On Module, from any tab
press i followed by the required key.
2. Select Name and enter the name to be associated with the selected key, then press OK.
The desired name is associated with the key.
3. Select Number and enter the telephone number to be associated with the key, then press
OK.
The desired number is associated with the key.
4. Press Exit to go back to the home page.

4.7 V24/CTI Interface Module

              4-65

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

4.7.1 Hardware description

4.7.1.1 Overview
The V24/CTI Interface Module allows a Data Terminal Equipment (DTE) to be connected to
the OmniPCX Office, via a UA link, by means of an RS232 serial link (CTI port) or a V24 link.
The V24/CTI Interface Module can be used alone or combined with an Alcatel-Lucent 9 series
set.
The V24/CTI Interface Module replaces the 4093 PLUGWARE V24/CTI. The two interface
modules can operate together: a data link can be set between an V24/CTI Interface Module
Interface Module and a 4093 PLUGWARE V24/CTI.
Note:
The V24/CTI Interface Module is also compatible with UA 3G sets.
CTI port
The RS232 serial link carries signalling (up to 9600 bit/s) and allows telephone operations
such as call management and call monitoring. The audio part is carried out by the associated
dedicated set.
V24 port
The V24 port is considered as a DCE and provides a capacity of 19200 bit/s (ECMA 102) for
an asynchronous V24 transmission. The electrical interface complies with the V28
recommendation of the CCITT.

Figure 4.48: V24/CTI Interface Module Configuration Example

4.7.1.2 Compliant Standards

4.7.1.2.1 Safety Requirements
- EN60950: European requirements
- UL 1950: US requirements
- CAN/CSA-C22.2 No 950-95: Canada

4-66              

Downloaded from www.Manualslib.com manuals search engine

     &' (

4.7.1.2.2 ECM
- EN55022: Limits and methods of measurement of radio interference characteristics of
information technology equipment
- EN55024: Limits and methods of measurement of immunity characteristics of information
technology equipment
- FCC part15: US requirements
4.7.1.2.3 V24 & CTI
- CCITT Rec.: V24,V28, V25bis, V54, V110
- Hayes protocols
- ECMA 102: Attachment requirements for pan-European approval for connection to PSTN
of TE (excluding TE supporting the voice telephony service) in which network addressing,
if provided, is by means of DTMF signalling
4.7.1.2.4 Environment Classes
- ETS 300 019: Environmental conditions and tests for telecommunication equipment:
• Part 1-1: Storage
• Part 1-2: Transportation
• Part 1-3: Environmental conditions
4.7.1.2.5 Eco Design
- ISO 14040: Environmental management – Life cycle assessment – Principles and
framework (1997)
- RoHS

4.7.2 Hardware configuration

4.7.2.1 Overview
Serial number: 3GV27015AB

              4-67

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

4.7.2.2 Jumpers
The jumper in a gray background is factory installed.

To configure the V24/CTI Interface Module, open the device with the 2 screws located under
the module.
If the jumper is positioned for "stand-alone" operation, an associated set cannot work.
If the jumper is positioned for "associated UA set" operation, the associated set is mandatory,
the Interface Module cannot work without it.

4.7.3 External connections

4.7.3.1 V24/CTI Interface Module Connection

4-68              

Downloaded from www.Manualslib.com manuals search engine

     &' (

The V24/CTI Interface Module is connected as follows:

Figure 4.51: V24/CTI Interface Module Connection

The V24/CTI Interface Module is connected to:
1. The digital set 3 m maximum length ( RJ11/RJ11 cable)
2. The PCX via a wall socket and a distributor frame
3. The CTI or V24 terminal:
• V24: 3m maximum length
• CTI: 3m maximum length
4.7.3.2 V24/CTI Interface Module Rear Panel Details

Figure 4.52: Rear Panel

1. RJ11 connector for UA line to PCX

              4-69

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

2. V24 SUBD9 connector

3. CTI SUBD9 connector

Figure 4.53: Connector Details

RS 232 port (V24):
Pin Signal Description
1 DCD Data Carrier Detect.
2 TX Transmit data.
3 RX Received data.
4 DTR Data Terminal Ready.
5 GND Protective ground.
6 DSR Data Set Ready.
7 RTS Request To Send.
8 CTS Clear To Send.
9 RI Ringing Indicator.

CTI port:
Pin Signal Description
1
2 TX Data transmission
3 RX Data reception
4
5 GND Protective ground
6
7 RTS Transmission request
8 CTS Ready for transmission
9

4.8 AP Interface Module

4.8.1 Hardware description

4-70              

Downloaded from www.Manualslib.com manuals search engine

     &' (

4.8.1.1 Overview
The AP Interface Module (Analog Peripheral) allows an analog device such as fax, modem,
minitel, answering machine to be connected to the Alcatel-Lucent OmniPCX Office
Communication Server via a UA link.

Figure 4.54: Example of Configuration with an AP Interface Module

AP Interface Module can be used alone or combined with an Alcatel-Lucent 9 series set.
Note:
The AP Interface Module is also compatible with Alcatel Reflexes sets.
AP Interface Module powers the analog device (DTMF signalling, ringer) and, to do this,
requires an external power supply (230V AC/30V AC adapter). In this document, this set is
called Z set.
4.8.1.2 Compliant Standards
4.8.1.2.1 Safety Requirements
- EN60950: European requirements
- UL 1950: US requirements
- CAN/CSA-C22.2 No 950-95: Canada
4.8.1.2.2 ECM
- EN55022: Limits and methods of measurement of radio interference characteristics of
information technology equipment
- EN55024: Limits and methods of measurement of immunity characteristics of information
technology equipment
- FCC part15: US requirements
4.8.1.2.3 Analog Transmission

              4-71

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

- ETS 300 439: Business TeleCommunications (BTC); Transmission characteristics of digital

Private Branch eXchanges (PBXs)
- TBR21: Attachment requirements for pan-European approval for connection to PSTN of
TE (excluding TE supporting the voice telephony service) in which network addressing, if
provided, is by means of DTMF signalling
4.8.1.2.4 Environment Classes
- ETS 300 019: Environmental conditions and tests for telecommunication equipment:
• Part 1-1: Storage
• Part 1-2: Transportation
• Part 1-3: Environmental conditions
4.8.1.2.5 Eco Design
ISO 14040: Environmental management – Life cycle assessment – Principles and framework
(1997)

4.8.2 Hardware configuration

4.8.2.1 Overview
Commercial Serial number: 3GV27014xx
Technical Serial number: 3GV26014xx

Note:
xx represents 2 letters depending on country.

4-72              

Downloaded from www.Manualslib.com manuals search engine

     &' (

4.8.2.2 Jumper
The jumper in a gray background is factory installed.

To configure the AP Interface Module, open the device with the 2 screws, located under the
module.
If the jumper is positioned for "stand-alone" operation, an associated set cannot work.
If the jumper is positioned for "associated digital set" operation, an associated set is
mandatory, the Interface Module cannot work without it.

4.8.3 External connections

4.8.3.1 Connecting AP Interface Module

Figure 4.57: AP Interface Module Connections

The AP Interface Module is connected to:
1. Digital set ( RJ11/RJ11 cable). 3 m maximum length
2. Alcatel-Lucent OmniPCX Office Communication Server via a wall socket and a distributor

              4-73

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

frame.
Connect an AP module is identical to connect a digital set.
Maxinum length between AP module and PCX depends on cable quality. For example:
• LY 0.5 mm cable: up to 800 m
• Ref 278 0.6 mm cable: up to 1200 m
3. Analog device with an RJ45 or RJ11 cable. 100 m maximum length
4. Power supply unit (see details below)
Caution:
The mains power supply unit is used as a sectioning device. This device should be easily
accessible.
4.8.3.2 Rear Panel Details

Figure 4.58: AP Interface Module Rear Panel

1. Socket for UA line to PCX
2. RJ45 socket for analog device connection
3. Power supply socket

Figure 4.59: Socket Details

PCX and digital set socket:
Pin Description
1 Not used
2 External Ringing 1
3 UA line 1
4 UA line 2
5 External Ringing 2

4-74              

Downloaded from www.Manualslib.com manuals search engine

     &' (

6 Not used

Analog device socket:

Pin Description
1 Not used
2 Not used
3 Not used
4 Analog line
5 Analog line
6 Not used
7 Not used
8 Not used

Power supply connector:

Pin Description
1 26V AC
2 26V AC

4.8.3.3 Power Supply Details

The power supply unit depends on country:
Reference Characteristics Country
1AF01101BAAA 230V AC/26V AC 130mA Europe
1AF01101DAAA 230V AC/26V AC 130mA UK
1AF01101AAAA 115V AC/26V AC 130mA USA

4.8.3.4 Environment
Working temperature: 5°C to 45°C
Stocking temperature: -40°C to 70°C
Relative humidity: 5% to 85%

4.9 S0 Interface Module

4.9.1 Hardware description

4.9.1.1 Overview
The S0 Interface Module allows an S0 bus (2 B + 1 D channels) to be connected to the
Alcatel-Lucent OmniPCX Office Communication Server via a UA link. This bus allows S0
terminals (S0 sets, PCs equipped with an S0 interface, Fax G4, modem, etc.) to be connected.
The S0 Interface Module can be used alone or combined with an Alcatel-Lucent 9 series set.

              4-75

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

Note:
The S0 Interface Module is also compatible with Alcatel Reflexes sets

Figure 4.60: Example of Configuration with an S0 Interface Module

The S0 module provides an S0 bus supplying power. An external power supply (230V AC/48V
DC adapter) is required.
There are two possible operating modes on the S0 bus:
- Non permanent layer: layer 1 must be set up by the calling end (PCX or terminal) at the
start of each call; layer 1 is shut down at the end of the call
- Permanent layer: operation of the S0 bus depends on the direction in which the initial call
was set up:
• If the call was set up from the PCX to the terminal, layer 1 is kept when the call ends.
• If the call was set up from the terminal to the PCX, layer 1 is shut down at the end of
the call. It must be set up again for the following call. If operation is incompatible with
the terminal used, there are two possible solutions: Either layer 2 is kept, this prevents
layer 1 being shut down, or, layer 1 is set up from the PCX by making a call to the
terminal. The call does not need to get through.
4.9.1.2 Compliant Standards
4.9.1.2.1 Safety Requirements
- EN60950: European requirements
- UL 1950: US requirements
- CAN/CSA-C22.2 No 950-95: Canada
4.9.1.2.2 ECM

4-76              

Downloaded from www.Manualslib.com manuals search engine

     &' (

- EN55022: Limits and methods of measurement of radio interference characteristics of

information technology equipment
- EN55024: Limits and methods of measurement of immunity characteristics of information
technology equipment
- FCC part15: US requirements
4.9.1.2.3 ISDN
- ETS 300 012: Basic user-network interface layer 1 specification and test principles
- TBR3: Attachment requirements for terminal equipment to connect to an ISDN using ISDN
basic access
- ETS 300 047: Basic access-safety and protection
- I.430: Basic user-network interfaces layer 1 specification
4.9.1.2.4 Environment Classes
- ETS 300 019: Environmental conditions and tests for telecommunication equipment:
• Part 1-1: Storage
• Part 1-2: Transportation
• Part 1-3: Environmental conditions
4.9.1.2.5 Eco Design
ISO 14040: Environmental management – Life cycle assessment – Principles and framework
(1997)

4.9.2 Hardware configuration

4.9.2.1 Overview
Commercial Serial number: 3GV27016AB
Technical Serial number: 3GV26016AB

              4-77

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

4.9.2.2 Jumper
The jumper in a gray background is factory installed.

To configure the S0 Interface Module, open the device with the 2 screws, located under the
module.
If the jumper is positioned for "stand-alone" operation, an associated set cannot work.
If the jumper is positioned for "associated digital set" operation, an associated set is
mandatory, the Interface Module cannot work without it.

4.9.3 External connections

4.9.3.1 Connecting the S0 Interface Module

4-78              

Downloaded from www.Manualslib.com manuals search engine

     &' (

Figure 4.63: S0 Interface Module Connection

The S0 module is connected to:
1. A digital set (optional), via an RJ11/RJ11 cable of a 3 m maximum length
2. The Alcatel-Lucent OmniPCX Office Communication Server, via a wall socket and a
distributor frame
Connecting an S0 module is identical to connecting a digital set.
The maximum length between the S0 module and the PCX depends on cable quality. For
example:
• LY 0.5 mm cable: up to 800 m
• Ref. 278 0.6 mm cable: up to 1200 m
3. The S0 bus.
4. A Mains power supply unit: AC/DC converter (see details below)
CAUTION: The mains power supply unit is used as an S0 module sectioning device. This
device should be easily accessible.
4.9.3.2 Alcatel-Lucent S0 Interface Module Rear Panel Details

              4-79

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

Figure 4.64: Rear Panel Details

1. RJ11 socket for UA line
2. RJ45 socket for S0 bus
3. Power supply socket

Figure 4.65: Socket Details

PCX and digital set socket:
Pin Description
1 Not used
2 External Ringing 1
3 UA line 1
4 UA line 2
5 External Ringing 2
6 Not used

S0 bus RJ45 socket:

Pin Description Polarity
1 Not used
2 Not used
3 Transmission +
4 Reception +
5 Reception —
6 Transmission —
7 Not used

4-80              

Downloaded from www.Manualslib.com manuals search engine

     &' (

8 Not used

Power supply socket:

Pin Description
1 0V
2 40V DC

4.9.3.3 Power Supply Details

The interface module local power supply is required only when S0 terminals do not have their
own local supply.
The power supply unit depends on country:
Reference Characteristics Country
1AF00446CAAA 230V AC/42V DC 150mA Europe
1AF00446ABAA 127V AC/44V DC 150mA Brazil
1AF00446AGAA 220V AC/42V DC 150mA Argentina
1AF00446ASAA 240V AC/42V DC 150mA Australia
1AF00446AUAA 115V AC/42V DC 150mA USA
1AF00446BAAA 230V AC/42V DC 150mA UK

4.9.3.4 Environment
Working temperature: 5°C to 45°C
Stocking temperature: -40°C to 70°C
Relative humidity: 5% to 85%

4.10 Intelligent Base Stations

4.10.1 Detailed description

This notice describes the rules to follow for an installation comprising three or four DECT
bases.
For a larger installation, a preliminary study must be carried out using coverage tools. The
bases are then installed according to the results of this study.
4.10.1.1 CONNECTION
The Alcatel-Lucent 4070 IO is designed for internal installation in the building, while the
Alcatel-Lucent 4070 EO is designed for external installation.
The 4070 EO IBS comes in a plastic box and is protected against temperature variation.
The 2 antennae are outside the box so that they both have the same signal reception.
Intelligent Base Stations (IBS) are fitted with a red LED that gives information about the state
of the Base Station:

              4-81

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

- Fixed LED:
1. Software downloading
2. Initialization phase, waiting for synchronization
3. Software problem, IBS stopped.
- Fast blink: There is a problem with the line.
- Short ON, long OFF: Running on 1 UA link.
- 500ms OFF, 500ms ON: Running on 2 UA link.
The IBSs can run and be powered remotely by the UA access (this is the most common
configuration). But they can also be powered by a power device. This is used when there are a
lot of IBSs and the system power cannot support all the connected IBSs.
A base station may be connected to 1 or 2 UA links (UAI boards) and allows 3 or 6
simultaneous connections with DECT/GAP terminals.
The need for three or six communication channels depends on the number of cordless stations
and on the DECT traffic to be managed.
In the event of a two-cable connection:
- use two interfaces neighboring a UAI board
- use the even-numbered interface for the master link and the other for the slave link.
Both cables should have the same length. The first interface of the system’s UAI16 board

should not be used since the operator station uses those points.

4.10.1.2 NUMBER OF USEFUL BASE STATIONS

Any radio signal is subject to various propagation phenomena: attenuation, reflection and
diffraction. These phenomena are related to the environment of the Alcatel-Lucent 4070
IO/EO, and affect the radio performance of the system.
The effects can improve or deteriorate wave propagation.

4-82              

Downloaded from www.Manualslib.com manuals search engine

     &' (

Take as an example a building with a metallic structure. A radio wave will tend to be subject to
many reflections which will consequently degrade system performance.
Moreover, the range of an Alcatel-Lucent 4070 IO/EO is very dependent on the amount of
attenuation subjected to the radio wave across various zones.
The following table gives the values of global coverage zone (cell) for an Alcatel-Lucent 4070
IO/EO under normal environmental and topological conditions:
Interior Exterior
Coverage area ~ 50 m ~ 400 m
2
Area: ~ 7,000 m ~ 50 000 m 2

4.10.1.3 NUMBER OF USERS PER BASE STATION

Type of Base Station connection. Number of DECT users

3 channels 4
6 channels 12

4.10.1.4 LOCATING DECT BASE STATIONS

As a result of the environment and the infrastructure, certain recommendations must be taken
into account for locating Alcatel-Lucent 4070 IO/EO:
Recommendations for location Possible solutions
INTERIOR As far as possible from walls Suspend Alcatel-Lucent 4070 IO/EO in a
COVERAGE clear zone
Do not fix directly to a metallic structure Move Alcatel-Lucent 4070 IO/EO into
another zone
Do not place in false ceilings or in telecom Place Alcatel-Lucent 4070 IO/EO in useful
rooms zones (corridors)
As far as possible from industrial machines Place 4070 IO/EO in useful zones
or electrical cabinets
EXTERNAL Place the base stations in an open space Attached to pylons for example
COVERAGE (as far as possible from buildings)
Place the base stations higher than low At the top of buildings on pylons for
obstacles (trees, cars etc.) example

4.10.1.5 INTERACTIONS
Interactions with other features
IBS DECT and IBS PWT (Personal Wireless Telecommunications) cannot run together on the
same system. The first IBS plugged determines the system type (DECT or PWT).
To switch from one system to another, unplug all IBSs, make a warm restart and plug in the
IBSs.
Interactions with other applications
IBSs are fully compatible with other wireless technologies such as VOWLAN.

              4-83

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

Interactions with other software releases

OmniPCX Office release 5.1 requires 4 kinds of DECT initialization: Europe, Latin America,
United-States and China. See also: IBS CONFIGURATION .
4.10.1.6 LIMITS
Number of IBSs: 20 IBSs per cabinet is recommended, however, the number of IBSs is only
restricted by the available power.
DECT link limit: 3 links on an IBS with one UA access, 6 links on an IBS with 2 UA accesses.
DECT handset limit: up to 120 handsets on a system.
4.10.1.7 PERFORMANCE AND QUALITY
IBSs are downloaded during the system start phase or when hot plugged. A system with many
IBSs plugged might take longer to complete the start phase.
Downloading 1 IBS takes about 30 seconds. It takes more time when several IBSs are
plugged on the same UA resource.
The end of restart is only possible after all the devices have been taken into account.
If an IBS downloading fails, the IBS restarts with the previously installed software.
4.10.1.8 IBS CONFIGURATION
There is no hardware configuration for IBS other than selecting between an external power
supply for each IBS and remote power by system.
To configure the IBS software:
ARI Number
The ARI number identifies each OmniPCX Office. Each OmniPCX Office has an identical
default ARI number.
When you install a new OmniPCX Office, you have to change the default ARI number. You
can only keep the first digit, which is "1" and which means "ARI type B".
- 1 In OMC, go to System Miscellaneous -->DECT/PWT ARI/GAP
- 2 Enter your own number (octal digit) to register your DECT handset.

4-84              

Downloaded from www.Manualslib.com manuals search engine

     &' (

Figure 4.67: ARI Number

Note 1:
The ARI Number is the only non plug and play device on the IBS.
The default configuration fits with the major systems. Modifications should answer to specific needs.
Line length
The Line length is the cable length used to plug the IBS to the system (distance between the
IBS and OmniPCX Office). It enables the system to add a delay in signal and to avoid a shift in
clock signal that creates a reset of the IBS.
- 1 In OMC, go to Users/Base stations List.
- 2 Select the IBS Master and click Details
There are 3 possibilities of configuration:
- Short line (0-400 meters)
- Medium line (400-800 meters)
- Long line (800-1200 meters)
Restart the IBS after you have modified the Line length parameter.
Antenna diversity
Antenna diversity is the ability of the IBS to move the transmission and reception from one
antenna to the other so that the signal is always of the highest quality.
Restart the IBS after you have modified the Antenna diversity parameter.
Silent-Noisy IBS
Enable the Silent-Noisy IBS parameter to set up the echo canceller device.

              4-85

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

The IBS is fitted with a software device that analyses audio signals and eliminates echo and
noises. This device is activated by default.
When an IBS is deployed in a noisy environment, a lot of signals, including Speech ones, are
eliminated while in Conversation state. This leads to bad Speech quality.
You have the option to disable the echo canceller. In that way, the speech and the noise
signals are not filtered. It is then to the user to identify the speech.
Frequency plan
In OMC, go to System Miscellaneous# DECT/PWT Frequencies to select signals. In OMC,
you can configure both the DECT and PWT frequency plans, regardless of what types of
handsets are plugged on the system.

Figure 4.68: DECT/PWT Frequencies

Note 2:
Due to hardware, there is a limit in the number of channels that you can configure.
You can configure the following numbers of channels:
- DECT EUROPE, LATAM, CHINA: 1, 2, 4, 5, 8, 10 channels
- DECT US: 1, 2, 4, 5 channels
- PWT: 1, 2, 4, 5, 8 channels
4.10.1.9 Initialization

4-86              

Downloaded from www.Manualslib.com manuals search engine

     &' (

Once the IBS finishes the downloading, the system starts the initialization.
The system synchronizes the signals of the IBSs so that handovers are possible. The system
selects the T0, T2, or CPU main board clock as the source.
Then the system sends the following data:
- Fixed part capabilities (Full slot, frequency control, page repetition, setup on dummy, basic
A field setup): value sent = 0x007910
- Line length: Short line
- Frequency plan (2 bytes)
Some countries have shifted DECT frequencies. In order to be compatible with all frequency
bands in the different countries, 4 types of initialization of frequency plans are available:
Europe, Latin America, The United-States and China.
table 4.35: RF Band Europe
Channel TX Freq RX Freq
0 1897.344 1898.206
1 1895.616 1896.480
2 1893.888 1894.752
3 1892.160 1893.024
4 1890.432 1891.296
5 1888.704 1889.566
6 1886.978 1887.840
7 1885.248 1886.112
8 1883.520 1884.384
9 1881.792 1882.656

Note 1:
By default, all frequencies used
Value sent to IBS: 0x3FF
0000 0011 1111 1111
table 4.36: RF Band China
Channel TX Freq RX Freq
0 1918.060 1918.944
1 1916.352 1917.216
2 1914.624 1915.446
3 1912.898 1913.760
4 1911.188 1912.032
5 1919.440 1910.304
6 1907.712 1908.576
7 1905.964 1906.848
8 1904.256 1905.120

              4-87

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

9 1902.528 1903.392

Note 2:
By default, all frequencies used
Value sent to IBS: 0x3FF
0000 0011 1111 1111
table 4.37: RF Band Latam
Channel TX Freq RX Freq
0 1928.448 1929.312
1 1926.720 1927.584
2 1924.992 1924.992
3 1923.264 1923.264
4 1921.536 1921.536
5 1919.808 1919.808
6 1918.060 1918.060
7 1916.352 1916.352
8 1914.624 1914.624
9 1912.896 1912.896

Note 3:
By default, all frequencies used
Value sent to IBS: 0x3FF
0000 0011 1111 1111
table 4.38: RF Band US
Channel TX Freq RX Freq
3 1928.448 1929.312
4 1926.720 1927.584
5 1924.992 1925.856
6 1923.264 1924.128
7 1921.536 1922.400

Note 4:
By default, only 5 frequencies used
Value sent to IBS: 0x03E0
0000 0011 1110 0000
table 4.39: RF Band PWT
Channel Center Freq
0 1929.375
1 1928.125

4-88              

Downloaded from www.Manualslib.com manuals search engine

     &' (

2 1926.875
3 1925.625
4 1924.375
5 1923.125
6 1921.875
7 1920.625

Note 5:
By default, 8 frequencies used
Value sent to IBS: 0x03FC
0000 0011 1111 1100

4.10.2 Safety rules

4.10.2.1 ENVIRONMENTAL PROTECTION
For an exterior installation, it is necessary to take precautions against lightning affecting the
location of the Alcatel-Lucent 4070 IO/EO.
4.10.2.1.1 Conditions for using lightning protection:
Protection of Alcatel-Lucent 4070 IO/EO against lightning should be used when they:
- are less than 1.5 m from a wall more than 2 m below the antenna.
- use an external airborne connection between the base station and the system.
4.10.2.2 RECOMMENDATIONS FOR EXPOSURE OF THE PUBLIC TO THE
ELECTROMAGNETIC FIELD
4.10.2.2.1 MAGNETIC ABSORPTION RATE
Exposure of the public to the electromagnetic field from DECT sets and base stations is
measured using the Specific Absorption Rate (SAR) measuring unit. 2W/kg is the SAR limit
value indicated in international recommendations and also in the European recommendation
(1999/519/EC).
The DECT authorised SAR limit value is 2 Watts/kilogram on 10g of body tissue (local SAR).
International recommendations include a safety margin for the public and take account of
possible measuring variations.
SAR values
- Set: as the average power emitted from a set is lower than 20mW, the set is considered to
comply without having to undergo any tests (see: EN 50371). The SAR value for DECT
sets (e.g.: Mobile Reflexes) is not significant.
- Base station: the local SAR (head and chest) on 10g of body tissue for DECT base
stations (e.g.: 4070) is lower than 0.5 W/kg (this is with an integrated omni-directional
antenna).
4.10.2.2.2 ANTENNAE CHARACTERISTICS

              4-89

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

Integrated antennae
The following is a list of characteristics for integrated antennae:
- Bandwidth: 1.88 to 1.93 Ghz
- Impedance: 50 Ohms
- TOS: 1.5:1
- Gain: 3 dBi (maximum)
- Polarization: vertical (axis of the antenna)
- Width of the beam at 3 dB (vertical): 90º
- Radiation diagram: omni-directional in the horizontal plane.
External antennae
According to the ETSI EN 301 406 standard, DECT antenna gain is limited to 12 dB +/-3dB. In
the case of external directional antennae, if a minimum safety distance of 50 cm is respected,
the SAR value is the same as the value obtained in the case of an integrated omni-directional
antenna (and therefore, lower than: 0.5 W/kg).
4.10.2.2.3 CONFORMANCE PERIMETER FOR EXPOSURE OF THE PUBLIC
- Integrated omni-directional antennae: no limit for the conformance perimeter
- External antenna (directional): the installation must allow for a safety perimeter respecting
a minimum distance of 50 cm.
4.10.2.3 RECOMMENDATIONS FOR INSTALLATION
4.10.2.3.1 Standard Topology.
The various building infrastructures are grouped into three types of geometric shape.
Coverage areas SQUARE: Coverage areas RECTANGULAR Coverage areas ROUND
:

The distances quoted below give an idea of typical range of a base station. It is clear that a
rectangular zone requires more base stations to provide full coverage.
4.10.2.3.2 Layout technique
For structures with a number of floors, different solutions can be envisaged as a function of:
- the coverage obtained at each level.
- the position of the Alcatel-Lucent 4070 IO/EO (higher or lower level).
Installation examples

4-90              

Downloaded from www.Manualslib.com manuals search engine

     &' (

Square zone Rectangular zone

Example 1: square building Example 2: rectangular building

st
1 floor 1st floor

2ndfloor 2ndfloor

It is possible to alter the number of base stations used

from one floor to another for this type of building.

The technique used is overlapping the location of base stations from one level to another. This
technique can be used for alternate floors if the coverage of a level can be achieved from an
adjacent level.
4.10.2.3.3 Coverage depending on the infrastructure

              4-91

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

The solution proposed alternates two stations per floor with overlapping locations from one
floor to another. The zones shown by unbroken circles correspond to the zones covered by
each station (B1, B2, B3, B4).
The zones in bold correspond to the coverage at a given level from a station on the floor above
or below.

4.11 PIMphony

4.11.1 Overview
Alcatel-Lucent PIMphony is a personal productivity tool that connects your phone terminal
(dedicated, analog or DECT wireless set) with your computer, providing enhanced usage of
your telephone.
PIMphony IP is an IP phone that provides the same level of features as PIMphony associated
with an actual terminal. PIMphony IP is based on Voice over IP technology (VoIP). No physical
terminal is required.

4-92              

Downloaded from www.Manualslib.com manuals search engine

     &' (

Alcatel-Lucent PIMphony also provides tight integration with the most popular PIMs (Personal
Information Managers) on the market, enabling them for Computer Telephony.
Note:
For information and details concerning Alcatel-Lucent PIMphony installation, refer to the Installation
Manual section in the PIMphony Online Help.
The PIMphony Online Help is available:
- from the PIMphony CD-Rom and the Documentation CD-Rom: open the aochelp.chm file to access
the Online Help
- from the PIMphony application : once it is installed on your PC, press F1 to open the Online Help

4.11.2 Additional Information

4.11.2.1 Hardware aspects
table 4.43: PCX Requirements
Version Hardware Requirements
PIMphony 6.5 OmniPCX Office R5.x, R6.x, R7.x and R8.x

table 4.44: PC Requirements

Version Hardware Requirements
PIMphony 6.5 PII 300 Mhz+ 128MB Ram + 2GB HD (140MB free
space to install PIMphony) + SVGA (1024x768) +
Ethernet Board + Keyboard + Mouse
Sound card for PIMphony IP
USB port or serial port for use of a headset with
PIMphony IP

4.11.2.2 Software aspects

table 4.45: Supported and unsupported software
Supported Windows See table: Supported Windows OS
OS
Unsupported All Windows version before Windows 2000 SP4 Pro
Windows OS Only for PIMphony Multimedia : Windows Server 2003
It is not recommended to use PIMphony 6.3 in other than the above
mentioned OS list.
Internet Explorer Internet Explorer 6.0 or more recent
Office Outlook 2000, XP, 2003, 2007, 2010 (32 bits and 64 bits edition)
Access 2000, XP, 2003, 2007, 2010 (32 bits edition)
Goldmine Goldmine 5.7
Goldmine 6.5, 6.7, 7.0, 7.5, 8.0, 8.5, 9.0
Act Act! 6, Act! 2006 (8.0), Act! 2007 (9.0), Act! 2008 (10.0), Act! 2009
(11.0), Act! 2010 (12.0), Act! 2011 (13.0), Act! 2012 (14.0)
Lotus Notes IBM Lotus Notes 5.02 to 6.5, Lotus Notes 8.0, Lotus Notes 8.5.

table 4.46: Supported Windows OS

              4-93

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

OS PIMphony PIMphony TSP SPI for

IP Microsoft
TAPI
Server
Windows 2000 Server (with SP4) [32 bits] Yes No No Yes
Windows 2000 Pro (with SP4) [32 bits] Yes Yes Yes No
Windows Server 2003 (with SP1 or SP2) [32 Yes No No Yes
bits]
Windows Server 2003 R2 (with SP2) [32 bits] Yes No No Yes
Windows 2008 Server (with SP2) [32 bits] Yes No No Yes
Windows 2008 R2 Server (with SP1) [64 bits] Yes No No Yes
Windows XP [64 bits] Yes No No No
Windows XP Pro (SP1 or SP2 or SP3) [32 bits] Yes Yes Yes No
Windows XP Home (SP1 or SP2 or SP3) [32 Yes Yes Yes No
bits]
Windows Vista 32 bit edition (with SP1) Yes Yes Yes No
Windows Vista 64 bit edition (with SP1) Yes No No No
Windows 7 (with SP1) [32/64bit] Yes Yes Yes No

4.11.2.3 Limits
Simultaneous connected PIMphony users in HTTP: 200
Simultaneous connected PIMphony users in HTTPS: 25
Note:
Hard disk has no impact on the limits.

4.12 Reflexes Terminals

4.12.1 Installation procedure

4.12.1.1 REMINDER: SYSTEM - Alcatel Reflexes TERMINAL SEPARATION
- SYT type 0.5 mm cable: 800 m (terminal without option) or 600 m (terminal with S0 or Z
option)
- 278 type 1.6 mm cable: 1200 m (terminal without option) or 850 m (station with S0 or Z
option)
4.12.1.2 Premium AND Advanced Reflexes TERMINALS
4.12.1.2.1 Attaching the line cable:
- Turn the terminal
- Remove the panel at the rear of the terminal (pull it towards the interior of the terminal and
then pull it out).

4-94              

Downloaded from www.Manualslib.com manuals search engine

     &' (

- Plug in the line cable(connector ) and position it as shown in the illustration below.

- Replace the panel.

4.12.1.2.2 Attaching the handset cable:

- Turn the terminal
- Plug in the handset cable (connector ) into the guide intended for this purpose.

4.12.1.2.3 Wall mounted

Preparing Premium Reflexes terminals
- Turn the terminal
- Use a screwdriver to remove the two upper rubber feet.
Preparing Advanced Reflexes terminals
- Turn the terminal
- Use a screw driver to remove only the left rubber foot.
Mounting the terminal
- Use the bracket as a drilling template; use the wallplugs and screws provided to attach the
bracket.

              4-95

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

- Attach the terminal using the two lugs: introduce the lugs into the holes previously
occupied by the feet (left foot and hole intended for this purpose for Advanced Reflexes
terminals).
- Stabilize the mounting by clipping the foot into the base of the terminal.
4.12.1.2.4 Mounting optional modules:
- Turn the terminal
- Remove the panel situated at the rear of the terminal.
- Slide the module into the terminal
- Connet the module to the terminal (connector ).

- Join the module to the terminal using the 2 screws provided in the kit
- Connect the module output (connector UA) to the terminal's wall socket.

Example of using optional modules: connecting a charge management system

4-96              

Downloaded from www.Manualslib.com manuals search engine

     &' (

List of abbreviations
- TD: Transmit data - RD: Receive data
- RTS: flow control output - CTS: flow control output

4.12.1.2.5 Adding a Sector

- Turn the set and the module upside down
- Connect the unit to the terminal.
- Join the module to the set using the metallic strip and the 4 screws provided in the kit

4.12.1.3 Alcatel-Lucent First AND Easy Reflexes TERMINALS

4.12.1.3.1 Attaching the line cable:
- Turn the terminal
- Plug in the line cable(connector ) and position it as shown in the illustration.

Attaching the handset cable:

- Turn the terminal
- Plug in the handset cable (connector ) into the guide intended for this purpose.

4.12.1.3.2 Wall mounted

Preparing the terminal
- Turn the terminal
- Unscrew A and remove the metal plate.
- Slide this plate up the lower groove and secure it with screw B.
- Remove the handset hang-up lug by turning screw C through half a turn.

              4-97

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

Mounting the terminal

- Drill two hole respecting the dimensions given below.
- Position the supporting screws as shown below.
- Attach the terminal

4.12.1.3.3 Mounting optional modules:

For Alcatel-Lucent First and Easy Reflexes terminals, the optional module is external to the
terminal; this module can be placed on a table or wall mounted. The installation simply
involves connection between the terminal, the module and the wall sacket.
Wall mounting an optional module
- Drill two holes (separation = 105 mm, diameter = 6 mm).
- Position the fixing screws.
- Attach the module

4-98              

Downloaded from www.Manualslib.com manuals search engine

     &' (

4.13 Extending Your Installation

4.13.1 Detailed description

4.13.1.1 Configuration of Stations
4.13.1.1.1 Handset replacement
You can replace your digital terminal by connecting a terminal of the same family, but of a
different type, into your phone socket. This substitution can be temporary or permanent.
Replacing an analog set by another analog set, or replacing a digital set by a set of the same
type, requires no special procedure (simple hardware exchange).
Temporary substitution
The replacement set keeps its own default functions (customized settings are not transferred).
The data not transferred is stored in the Alcatel-Lucent OmniPCX Office Communication
Server system until a set of the same type as the initial one is connected.

Permanent replacement
The maximum quantity of data from the initial set is transferred to the replacement. Data not
transferred are deleted.

              4-99

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

Characteristics preserved during temporary or permanent set substitution

- Rights (restricted features)
- Barring level
- Metering profile
- Messages and last caller repertories
- Destination set for metering reminder, forwarding and/or monitoring
- Set belonging to a hunting group and/or a Manager-Secretary relation
- Appointment reminder
- Locked or unlocked set
- Callbacks
- Active forwarding
- Last number redial
Replacement of digital sets
Regardless of the type of the initial digital set and that of the replacement, the function and
resource keys are not preserved. The directory numbers are preserved in accordance with the
size of the directories of the stations concerned (for example, when replacing a Advanced
Reflexes set with a Premium Reflexes set, only the first 10 numbers are preserved).
The add-on modules are always transferred provided the substitution set supports these

modules.
Note:
It is possible to replace a Reflexes set with an Alcatel-Lucent 9 series set. It is not possible to replace an
Alcatel-Lucent 9 series set with a Reflexes set.

4.13.1.1.2 IP Touch set replacement

You can replace your IP Touch terminal by connecting a terminal of the same family only, into
your phone socket. This substitution can be temporary or permanent.
Temporary substitution
The default configuration is not preserved when replacing temporarily an IP Touch set by
another type of IP Touch set. The activation code and the replacement functions will be
refused.
The data downloading process is automatically activated and the correct files are selected.

4-100              

Downloaded from www.Manualslib.com manuals search engine

     &' (

Permanent replacement
The default configuration is not preserved when replacing permanently an IP Touch set by
another type of IP Touch set. The activation code and the replacement functions will be
refused.
The data downloading process is automatically activated and the correct files are selected.
4.13.1.1.3 Moving a handset
If you move office, you can move your set from one socket to another and still preserve all or
part of its settings.
Before relocating the set:
- You need to change the personal code, which must be different from the default code.
- It is advisable to lock the set.
Relocating a set to an unused socket

4.13.1.1.4 Adding sets

When adding sets, attention must be paid to the limits on the number of sets and the features
offered by the system software key.

The set is recognized as soon as it has been plugged into the socket.
4.13.1.1.5 Using a Multi Reflexes 4099 hub
Multi Reflexes 4099 option (also called Multiple UA hub) connects up to 3 Alcatel-Lucent 9
series or Alcatel Reflexes terminals to an Alcatel-Lucent OmniPCX Office Communication
Server using just one UA link. It simplifies the installation of additional Alcatel-Lucent 9 series
or Alcatel Reflexes terminals.

              4-101

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

This option does not allow the connection of DECT base stations, 4070 IO/EO,

Alcatel-Lucent 9 series sets or Alcatel Reflexes sets with V24/CTI Interface Module, S0
Interface Module or AP Interface Module.
Note:
IP Touch sets cannot be connected to a hub.

Interface classification
- UA link: TBTS
- Hub/Alcatel-Lucent 9 series or Alcatel Reflexes 1 to 3 : TBTS
Maximum distances between Alcatel-Lucent OmniPCX Office Communication
Server and sets
- 0,4 mm cable: 325 m

4-102              

Downloaded from www.Manualslib.com manuals search engine

     &' (

- 0,5 mm cable: 505 m

- 0.6 mm cable: 730 m
Cables of 3 m and 10 m are available for connecting the sets to the hub.
4.13.1.2 Adding/Replacing Boards
Except for PowerCPU, any board can be plugged/unplugged when the system is

powered up.
To replace a PowerCPU board:
- Press the ON/OFF button, the RED led will flash.
- Wait for the LED to go to steady red (about 30 seconds): the system is turned off.
With OMC you can save and subsequently restore the configuration after replacing the
PowerCPU board.
4.13.1.3 Connecting a Hard Disk

Figure 4.85: SATA Hard Disk Connection

During installation, always take anti-static precautions (wristband, heelpiece, etc.) before

handling the hard disk. Any degradation caused by electrostatic discharges will reduce
the life of the disk. Handle the hard disk by its sides and do not touch the connector.
When going into stand-by mode, wait for the red Power LED to stop flashing before you
remove the module's PowerCPU board. Extracting the disk before the switch to standby is
completed can destroy part of the disk or damage its contents. Never handle the hard
disk until the motor has stopped completely (about 4 seconds after the red Power LED stops
flashing).

              4-103

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

4.13.1.4 Adding a Module Expansion

It is possible to add one or two modules to the basic module.

4.13.1.4.1 Fitting a Module Expansion.

- The CPU slot of the module expansion must be fitted with a PowerMEX board with an
HSL1 daughter board.
- Fit the PowerCPU board of the main module with an HSL daughter board.
- A module expansion may only include synchronous digital network interfaces (BRA, PRA)
if this type of card is already incorporated into the main module (synchronization by the
main module).
- The same rules apply to the other boards as those which applied to the base module.
4.13.1.4.2 PowerMEX board.

4-104              

Downloaded from www.Manualslib.com manuals search engine

     &' (

RJ45 pin 1 2 3 4 5 6 7 8
MAIN: TX+ TX- RX+ RX-

- MAIN: HSL to basic module.

4.13.1.4.3 Role of the # key

Name Color Feature

POWER Red/Green - Mains operation: steady green led
- Battery operation: steady yellow led
- Standy: steady red LED
FAN Red/Green - Both fans functioning: steady green led
- 1 or both fans down: steady red led

4.13.1.4.4 Adding a third module

- Replace the HSL1 board of the PowerCPU board with an HSL2 board.
- Reuse this HSL1 board by placing it on the PowerMEX board of the third module.
In an installation using two modules, the PowerCPU (base module) and PowerMEX

(module expansion) boards are fitted with an HSL1 board.

4.13.1.5 Installation Upgrade
This section outlines the major considerations to be taken into account when migrating to R8.x
from:
- R3.x
- R4.x
- R5.x
- R6.x
- R7.x
Because of the hardware changes in R8.x, all the R8.x upgrade must be considered as an
on-site procedure.
The following procedures are based on minimal hardware configurations. For other services,
such as VoIP, enhanced VMU and ACD statistics, additional hardware is used and must be
taken into consideration.
Caution:

              4-105

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

If the hardware platform is downgraded, data can be lost.

For example, the removal of a hard disk is not supported:
- If ACD statistics are available
- If more than 4 hours VMU support is available
Lola installation is required and all data can be lost.

4.13.1.5.1 Upgrading Phone sets

All phone sets not supported in releases lower than R8.0 must be installed after the successful
migration to R8.x.
The phone sets not supported by earlier releases must not be plugged before migrating to a
version that can support them.
4.13.1.5.2 Migration
Prerequisites
To carry out an upgrade to R8.x, you need:
- A migration kit for the PowerCPU
- The correct version of R8.x with the R8.x software licenses
- LOLA R4.x
- Free disk space on the installer hard disk to contain all existing data
Migration to OmniPCX Office RCE Small, Medium, Large
The following sequence is used to migrate from an R3.x/R4.x/R5.x/R6.x/R7.x Alcatel-Lucent
OmniPCX Office Premium Edition CS or Alcatel-Lucent OmniPCX Office Advanced Edition CS
to R8.x OmniPCX Office RCE Small, Medium, Large.
1. Use the OMC, Release 8 to save configuration data.
2. In OMC off-line, adapt the saved database to R8.x hardware level (change CPU type,
remove CoCPUs).
3. Use LOLA to save customer data from the current main CPU (select option Migration
mono CPU).
4. Unplug the CPU and the unsupported boards from the system.
5. Change the existing hardware for R8.x hardware
6. Plug the PowerCPU.
7. Use LOLA to install the R8.x.
8. Use LOLA to restore the previously saved customer data.
9. Use OMC to restore the previously saved and modified configuration data.
Migration to R8.x OmniPCX Office RCE Compact
The following sequence is used to migrate to R8.x OmniPCX Office RCE Compact.
1. Use the OMC, Release 8 to save configuration data
2. In OMC off-line, adapt the saved database to R8.x hardware level (change CPU type,

4-106              

Downloaded from www.Manualslib.com manuals search engine

     &' (

remove CoCPUs).
3. Use LOLA to save customer data from the current main CPU (select option Migration
mono CPU)
4. Unplug the CPU and the unsupported boards from the system.
5. Change the existing hardware for R8.x hardware
6. If the PowerCPU board is equipped with a hard disk, check the presence of a power supply
module PSXS-N (reference: 3EH73072ACxx).
7. Plug the PowerCPU.
8. Use LOLA to install the R8.x.
9. Use LOLA to restore the previously saved customer data.
10. Use OMC to restore the previously saved and modified configuration data.
Configuration
After the hardware upgrade and migration, use the OMC configuration procedures to configure
the Alcatel-Lucent OmniPCX Office Communication Server .

              4-107

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4     &' (

4-108              

Downloaded from www.Manualslib.com manuals search engine

   
      

5.1 Detailed description

5.1.1 DEFAULT CONFIGURATION

5.1.1.1 Alcatel-Lucent IP Touch 4038 Phone, Alcatel-Lucent IP Touch 4068 Phone
and Alcatel-Lucent 4039 Digital Phone sets
Each of these sets has 2 programmable keys (F1/F2) and 40 virtual add-on keys. Their default
functions depend on:
- The configuration of the set (Operator, Manager, Assistant, Normal or Attendant)
- The market in which the set is sold (US or non-US)
- The operating mode of the set (KeySystem or PABX mode)
The default functions of the F1/F2 keys are summarized in the table below (they are the same
for KeySystem and PABX modes).
table 5.1: F1/F2 Key Functions
Market Set Configuration Key F1 Key F2
Non-US Operator Normal/Restricted Mode Operator Diversion
Manager Secretary Screening
Secretary Manager Screening
Normal Call Call
US Operator Manual Hold Transfer
Manager Manual Hold Transfer
Secretary Manual Hold Transfer
Normal Manual Hold Transfer

The default functions of the virtual keys are summarized in the figures below (separate figures
are provided for the US market). The virtual keys are selected using 8 physical buttons, 4 on
each side of the set's display. There are 5 pages of virtual keys (the pages can be scrolled
through using the up/down buttons of the set's 4-way navigator), with 8 virtual keys on each
page. Each of the following figures shows the first page of virtual keys and then indicates the
progression to the last (fifth) page of virtual keys.

              5-1

Downloaded from www.Manualslib.com manuals search engine

 Chapter 5   )"  & " (  

Figure 5.1: Virtual Key Functions for Operator Sets in KeySystem mode

5-2              

Downloaded from www.Manualslib.com manuals search engine

   )"  & " (  

Figure 5.2: Virtual Key Functions for Manager/Assistant/Normal sets in KeySystem Mode

              5-3

Downloaded from www.Manualslib.com manuals search engine

 Chapter 5   )"  & " (  

Figure 5.3: Virtual Key Functions for Attendant sets in KeySystem Mode (with no Physical
Add-on)

5-4              

Downloaded from www.Manualslib.com manuals search engine

   )"  & " (  

Figure 5.4: Virtual and Physical Add-on Key Functions for Attendant Sets in KeySystem mode

              5-5

Downloaded from www.Manualslib.com manuals search engine

 Chapter 5   )"  & " (  

Figure 5.5: [US only] Virtual Key Functions for Operator Sets in KeySystem Mode

5-6              

Downloaded from www.Manualslib.com manuals search engine

   )"  & " (  

Figure 5.6: [US only] Virtual Key Functions for Manager/Assistant Sets in KeySystem Mode

              5-7

Downloaded from www.Manualslib.com manuals search engine

 Chapter 5   )"  & " (  

Figure 5.7: [US only] Virtual Key Functions for Normal Sets in KeySystem Mode

5-8              

Downloaded from www.Manualslib.com manuals search engine

   )"  & " (  

Figure 5.8: Virtual Key Functions for Operator/Manager/Assistant/Normal Sets in PABX Mode

              5-9

Downloaded from www.Manualslib.com manuals search engine

 Chapter 5   )"  & " (  

Figure 5.9: [US only] Virtual Key Functions for Operator Sets in PABX Mode

5-10              

Downloaded from www.Manualslib.com manuals search engine

   )"  & " (  

Figure 5.10: [US only] Virtual Key Functions for Manager/Assistant Sets in PABX Mode

              5-11

Downloaded from www.Manualslib.com manuals search engine

 Chapter 5   )"  & " (  

Figure 5.11: [US only] Virtual Key Functions for Normal Sets in PABX Mode

5.1.1.2 Alcatel-Lucent IP Touch 4028 Phone and Alcatel-Lucent 4029 Digital Phone
sets
Each of these sets has 2 programmable keys (F1/F2) and 40 virtual add-on keys. Their default
functions depend on:
- The configuration of the set (Operator, Manager, Assistant, Normal or Attendant)
- The market in which the set is sold (US or non-US)
- The operating mode of the set (KeySystem or PABX mode)
The default functions of these keys are the same as for the sets detailed in Alcatel-Lucent IP
Touch 4038 Phone, Alcatel-Lucent IP Touch 4068 Phone and Alcatel-Lucent 4039
Digital Phone sets . However, in this case the virtual keys are selected using 4 physical
buttons, 2 on each side of the set's display, as shown below.

5-12              

Downloaded from www.Manualslib.com manuals search engine

   )"  & " (  

There are 10 pages of virtual keys (the pages can be scrolled through using the up/down
buttons of the set's 4-way navigator), with 4 virtual keys on each page.
5.1.1.3 Alcatel-Lucent IP Touch 4018 Phone and Alcatel-Lucent 4019 Digital Phone
sets
Each of these sets has 6 programmable keys which have the default functions indicated
below.

Figure 5.13: Key functions for Normal sets (in PABX mode)

5.1.1.4 Other predefined data

- Level 1 dynamic routing of stations: any unanswered call is routed to the voice mail unit
after 12 seconds.
- Level 2 dynamic routing of stations: only external call are routed to the operator group
after 24 seconds.
- OS calls overflow to general level (default operator group) after 24 seconds
- The default operator group contains the first two integrated voice server ports, general
ringer, remote XRA access and the first Alcatel Reflexes interface (Operator station)
- All the stations (except analog stations) are given a voice mailbox.
- The first analog interface is a Fax.

              5-13

Downloaded from www.Manualslib.com manuals search engine

 Chapter 5   )"  & " (  

5-14              

Downloaded from www.Manualslib.com manuals search engine

   
   !

6.1 System Startup from a Phone Set

6.1.1 Configuration procedure

You can start-up the system using a phone set, provided this phone set is either an
Alcatel-Lucent IP Touch 4038 Phone, Alcatel-Lucent 4039 Digital Phone, Alcatel-Lucent IP
Touch 4068 Phone or an Advanced phone set.
The phone set used needs to be defined as the operator phone set, that is the first phone set
connected to the system.
A start-up session is started automatically when the system is turned on for the first time.
Follow this start-up session to enter the data required to operate the system.
The procedures below show the Alcatel-Lucent IP Touch 4068 Phone interface, but the menus
are the same using the Alcatel-Lucent IP Touch 4038 Phone or Alcatel-Lucent 4039
Digital Phone interface and are similar using the Advanced interface.
In order to facilitate the first start-up, it is recommended that you have the following
information available:
- The number of your installation (international country prefix, national prefix, etc.).
- Basic metering unit value
- The ranges of numbers attributed by the network operator to the direct dial numbers (DDI)
of the terminals in your installation.
6.1.1.1 GENERAL DYNAMIC KEYS

Return to the previous menu Go to the next menu

Delete the last character Cancel

Move between the various
Validate an entry
options from those offered

Scroll up, down, left or right on the display

6.1.1.1.1 First POWER-UP

              6-1

Downloaded from www.Manualslib.com manuals search engine

 Chapter 6 *

To restart the session from the beginning during programming.

To restart the session if you quit using the Exit function

6.1.1.2 SYSTEM TYPE

: Used to define the system type: Business or Hotel

6.1.1.3 INSTALLATION NUMBER

This number must be entered in its entirety. The number of your installation can include a
maximum of three fields for a total of 18 digits.
The fields must be separated by an asterisk.
Possible fields include:
- International country prefix (for example: 33 for France): obligatory field.
- National prefix: optional field (has no meaning in France).
- Public number of the installation: obligatory field.
6.1.1.4 NUMBERING PLAN

6-2              

Downloaded from www.Manualslib.com manuals search engine

 *

: Used to choose one of the pre-programmed numbering plans: (2 to 4

digits, national or with *).
Any modification of the numbering plan causes the deletion of any existing DDI

numbers.
6.1.1.5 TERMINAL DDI NUMBERS
This function is used to define the DDI numbers (Direct Dialing Inwards) of all the terminals of
a Business system and the Administrative terminals (dedicated terminals) of a Hotel system.
Only one DDI number can be attributed to each internal directory number.

Access to the definition of terminal DDI numbers; displaying the first

internal directory number/DDI number.

The direct number includes up to 8 digit and can be modified (the cursor is placed at the start
of the field). The DDI numbers are generally the last 3 or 4 digits of your call numbers; the
public operator will let you know the range of numbers that has been assigned to you.

              6-3

Downloaded from www.Manualslib.com manuals search engine

 Chapter 6 *

Look through the list of internal directory numbers and

or
validate the entry displayed.
Delete the digits contained in the field "Direct no." (use the down arrow
navigator key to display this option)
Reject the complete list of DDI numbers as defined and return to the start
of the function.
Validate the complete list of DDI numbers.

The following error messages can appear when entering the data:
- "Number already used" : the DDI number is already attributed to another internal
number.
- "The specified number is outside the assigned range" : invalid DDI number (it contains
a * or # for example).
- "Direct Dialing Table full" : the maximum size of the table of public numbers (99 entries)
has been exceeded.
The following function is only available for Hotel installations.

Access the definition of a pool of DDI numbers for hotel rooms; display
the first DDI number.

6-4              

Downloaded from www.Manualslib.com manuals search engine

 *

10: Number of numbers still available in the DDI table after configuration of Direct Dial
numbers.
In a Hotel installation, all the Z terminals are used as hotel room terminals (except the first
which is a fax and the second which is a public telephone).
A pool of DDI numbers means that these terminals can be assigned with a dynamic DDI
number when a customer checks in.
The DDI numbers available depend on the number of numbers used by the administrative
terminals (a total of 99 numbers (or ranges of numbers for direct numbers) are available in the
table of public numbers for the system). The display shows the rank of the selected entry and
the total number of entries available for the hotel rooms.
or Look through the pool of DDI numbers and validate
the entry displayed.
Delete the digits contained in the field "Public no." (use the down arrow
navigator key to display this option)
Reject the complete list of DDI numbers as currently defined and return to
the start of the function.
Validate the complete list of DDI numbers.

6.1.1.6 NUMBER OF LINES CONNECTED TO THE PUBLIC NETWORK

This function is used to indicate the number of lines or B channels connected to the public
network (120 lines or 120 B channels maximum). These lines are then introduced into the
main bundle (depending on the order that the boards are taken into account) and made
available using the resource keys. On the operator terminal, T2 access can include up to 30 B
channels; T1 access up to 23 B channels; T0 access up to 2 B channels. The message "Value
exceed number of lines connected" is displayed when the value entered is greater than the
number of B channels connected.
6.1.1.7 OPERATION OF TERMINALS AND OPERATOR TERMINAL

              6-5

Downloaded from www.Manualslib.com manuals search engine

 Chapter 6 *

This function is only available for a business installation (in a Hotel only PCX mode is

used).
"PCX Mode" and "Intercom Mode"

PCX Mode: all the lines are available using two RSB keys (= resource key specific to a
bundle) .
Intercom Mode: the terminal has as many RSP keys (= resource key specific to an external
access) as there are lines on the system. Refer to the "Default Configuration" section in this
manual for a presentation of the function of the different keys for each type of terminal
depending on the operating mode selected.

6.1.1.8 ATTRIBUTING MAILBOXES

This function is used for assigning a voice mailbox to the installation terminals:
: choice between UA terminals, All terminals, and No terminal.

6.1.1.9 ARI NUMBER

6-6              

Downloaded from www.Manualslib.com manuals search engine

 *

This function is only available if your installation is fitted with DECT functions
The ARI (Access Right Identifier) number identifies the system uniquely to mobiles. It contains
11 octal digits (base 8). This number, assigned to an ETSI base by the installer, must be
entered on installing the system.
The first digit cannot be modified and is always set to 1. The cursor is automatically placed on
the second. The last digit is always either 0 or 4.
6.1.1.10 AUTHENTICATION

This is used to make secure data transmission between the system and DECT mobiles by
using an authentication code during registration
: choice between "off" and "on".

If the authentication mechanism is "on", the following screen is displayed.

Each access code can have a maximum of ten digits. This can be limited to the first four digits
if there are DECT stations other than the 100/200 Mobiles.
6.1.1.11 USER INFORMATION LANGUAGE

              6-7

Downloaded from www.Manualslib.com manuals search engine

 Chapter 6 *

Choice of language used on all the stations in the installation (display

and spoken help)
6.1.1.12 BASIC METERING UNIT COST

The value of the basic metering unit is introduced for calculating the cost of external calls. The
cost (not the duration) and the changes in the charge meters during calls are displayed. The
value entered can contain 5 figures (0-2 decimal places) in the chosen monetary unit. This
service is dependent on the subscription made with the operator.
Note:
Changing by duration required an external application.

6.1.1.13 TIME & DATE

The current date and time must be entered. Enter the date in the format DD/MM/YYYY.

Enter the time in the format HH:MM.

The message "Date and time must be programmed" is displayed when the "Date" and
"Time" fields are empty or contain the default values.

6-8              

Downloaded from www.Manualslib.com manuals search engine

 *

6.1.1.14 SYSTEM RESET

This menu is used to confirm resetting the system.

System reset; the display shows "System reset in progress"

After the reset, your system will operate with the new parameters entered.

6.2 System Startup from OMC

6.2.1 Overview
OMC is the PC application used to program the Alcatel-Lucent OmniPCX Office
Communication Server system via a local connection (V24 or LAN) or a remote connection
(the PC modem is connected to the Alcatel-Lucent OmniPCX Office Communication Server
integrated modem via the public network).
Three levels of programming are available using OMC:
- Easy View is used for Wizard configurations, i.e. the essential parameters for starting the
system.
- EasyPlus View is used for wizard-type configurations with the extensions offered by the
Advanced key. This key opens a window which is equivalent to Expert View.
- Expert View gives you unrestricted access to all the configuration possibilities.
The Wizard provides easy-to-use system programming, guiding the user step-by-step.

6.2.2 Installation procedure

6.2.2.1 Minimal PC Configuration
- Pentium 4 processor (or higher for windows XP).
- RAM: 512 Mb
- Windows 2003 (32 bits with SP1 or SP2), Windows 2003 R2 (32 bits with SP2), Windows
XP (32 bits with SP3 and framework.Net 2.0), Windows XP 64 bits or Windows Vista
(32/64 bits with SP1), Window 7 (32/64 bits), Windows server 2008, Windows server 2008
R2.
- Hard disk: 300 MB (recommended for installation and operation)
- Screen: 800 x 600 pixels

              6-9

Downloaded from www.Manualslib.com manuals search engine

 Chapter 6 *

- 1 mouse
- 1 serial port (connection to Alcatel-Lucent OmniPCX Office Communication Server for data
transfer)
- 1 Ethernet board (IP mode only; not required when there is a V24 serial port connection to
Alcatel-Lucent OmniPCX Office Communication Server)
- 64K (1 B-channel), or 128K (2 B-channels) PPP-compatible ISDN modem, or V34 modem
for remote access
Note:
Before installing OMC, the framework .NET must be installed.

6.2.2.2 Installing the OMC Software

The OMC software is installed from a CD-ROM.
Install the application by choosing options in the various windows.
When installation is finished, you access the application either:
- by double-clicking on the new icon created on the Windows desktop, or
- by selecting Start -> Program -> Alcatel-Lucent OmniPCX Office Communication
Server -> OMC XXX yy.z. The window Welcome to OMC appears.

6.2.3 Accessing the System

6.2.3.1 System Password

Important:
System Password management policy
Basic rules have to be applied to the different passwords allowing an OMC connection to the
system. It is recommended to change the default Installer password for OMC Expert,
Administrator password for OMC EasyPlus and Operator password for OMC Easy.
Remember these passwords can also be used from the MMC-Station.
The following are the recommendations for good password management:
- Implement company policy to regularly update all system passwords
- Regularly change the passwords
- Avoid the use of simple passwords such as 12345678, 11111111, 00000000 etc…
- Never choose a word from everyday language. Attackers can use special dictionary cracking
software to retrieve these
- Never choose a word that is closely related to you:
• your company name
• your name
• your wife’s maiden name
• the name of your children or your pet,
• your favourite hobby, etc…
- Choose a different password for each connection level

6-10              

Downloaded from www.Manualslib.com manuals search engine

 *

- Do not disclose passwords to other persons/colleagues

- Never write down your password. The first thing an attacker will do is rummage through your
personal belongings.
6.2.3.2 Local Access By LAN
The default IP address for the main CPU board is 192.168.92.246 for:
- A connection to the LAN port on the main CPU board via a UTP Category 5 5-100 ohm
crossover cable.
- A connection to the switch to which the main CPU board is connected by a direct cable.
The PC IP address and network mask must be compatible with the address of Alcatel-Lucent
OmniPCX Office Communication Server. For example 192.168.92.1 and 255.255.255.0.
For security reasons, the OmniPCX Office can be configured with an additional IP address,
which is used only for management.
To configure a management IP address:
1. Navigate to OMC: Hardware and Limits > LAN/IP Configuration
2. Select the LAN Configuration tab
3. Validate the Use Management IP Address checkbox
4. Enter the Management IP Address
5. Validate
6. Perform a warm reset to take the new address into account
6.2.3.3 Local V24 Access For OMC
It is possible to use OMC software to dialog with OmniPCX Office using a V24 connection. In
this case the network connection is not necessary.
A specific reinforced cable must link the "Config" RJ45 connector on the system CPU to the
Com port of the PC using OMC.
Wiring of the connection cable
RJ45 SUB D 9-point (F)
1 7
2 4
3 3
4 NC
5 5
6 2
7 6
8 8

6.2.3.3.1 Installation Procedure

1. Open the OMC software on the PC.
2. Select the Expert mode.
3. Select Comm from the menu toolbar.

              6-11

Downloaded from www.Manualslib.com manuals search engine

 Chapter 6 *

4. Select Connect from the dropdown menu. The Communication Path window is
displayed.
5. Select Local V24.
6. The system proposes installation of Alcatel-Lucent OmniPCX Direct V24. Click on Yes.
The Modem options window is displayed.
7. Click Add. The Installation window is displayed.
8. In the Installation window, check Don't detect my modem. Propose the option in a list
and click on Next.
9. Select the manufacturer.
10. Select Alcatel-Lucent OmniPCX Direct V24 (for Windows XP/2003/2000).
11. Select the Com port used.
12. Click Next.
13. Click Finish.
14. Click Close.
15. Back in OMC, click Comm. The Local V24 box is now enabled and the Com port is
displayed.
16. Click Ok and enter the password. It will take a few seconds for the OMC to connect to the
system.
6.2.3.4 OMC Remote Access By Modem
With remote access, you can use OMC to configure or download an Alcatel-Lucent OmniPCX
Office Communication Server system. This access can be managed using:
- an ISDN modem able to use ISDN PPP (point to point) protocol at 64K (1 B-channel) or
128K (2 B-channels)
- a V34 analog modem in Hayes protocol at 33600 bds
The management of these two modems is integrated into Alcatel-Lucent OmniPCX Office
Communication Server.
Important:
The OMC software must be installed on the remote maintenance PC, if Windows Terminal Server
is not being used.

6.2.3.4.1 Remote Access By ISDN Modem

ISDN Modem Recommended
Alcatel-Lucent OmniPCX Office Communication Server is equipped with a 64K (1
B-channel)/128K (2 B-channels) ISDN modem using PPP protocol for remote access through
the public network. It provides a point-to-point link accessible via standard LINUX procedures
(PPP, etc.).
For a 64K (1 B-channel) connection, the following modems are validated:
- KORTEX NOVAFAX ISDN 128000/33600 with PPP protocol
- FRITZ ¡X CAPI 2.0 or any standard "FRITZ" modem

6-12              

Downloaded from www.Manualslib.com manuals search engine

 *

- Multitech I Way Hopper MTA 128 ST 128 KBPS ISDN (see note below)
For a 128K (2 B-channels) connection, the following modems are validated:
- OLITEC USB ISDN 128K
- Multitech MTA128ST-RC ML-PPP (see note below)
- Eicon Diva 852 ISDN T/A USB - ISDN BRI ST - 128 Kbits/s
ISDN 64 to 128 KPBS modems handling the PPP protocol are generally compatible and
support CHAP authentication.
Note:
When using the Multitech modem, the authentication method must be set to CHAP. This is the default
method for current firmware versions. For modems with older firmware, you must either update the
firmware or activate CHAP with the AT command AT S58=3.

RAS Installation Process

In Windows 7/XP/Vista, you do not need to install new operating system components before
configuring a new access method; the Remote Access Services (RAS) component is installed
by default on these systems.
The sub-sections below describe how to set up the following remote access methods:
- Direct V24 Connection (OmniPCX Office Direct V24)
- Remote connection via ISDN modem (an example is provided for driver installation)
V24 Driver Installation Procedure
1. Open the Control panel.
2. Select Phone and Modem Options.
3. Select the Modems tab.
4. Click Add.
5. Check Don't detect my modem; I will select it from the list.
6. Follow the Wizard instructions to install the modem. You will need to choose the COM port
that will be associated with the modem.
7. You may need to reboot the PC to complete the installation.
Installing the Driver for an ISDN Modem (example)
The following procedure describes how to install a FRITZ modem.
1. Insert the modem installation CD-ROM.
2. Click the FRITZ ¡X PC Capi driver installer icon The wizard is displayed.
a. Indicate the serial port where the modem will be connected.
b. When the install process is complete, reboot the PC.
3. Insert the modem installation CD-ROM. The wizard is displayed
a. Click the FRITZ ¡32 Communication Software installer icon.
b. Select Install and configure.
c. Use the default installation (click on Next in each Wizard screen).

              6-13

Downloaded from www.Manualslib.com manuals search engine

 Chapter 6 *

d. At the end of the Wizard mode, check the Install Capi-port driver box.
4. Select AVM ISDN1 Internet (PPP over ISDN).
5. Reboot the PC.
Using Remote Access With OMC
1. Launch OMC. The OMC Welcome page is displayed.
2. Select the appropriate menu, as follows:
• the Expert menu, if you are logging in as "installer"
• the EasyPlus menu, if you are logging in as "administrator"
• the Easy menu, if you are logging in as "operator" or "attendant"
3. In the toolbar menu, click Comm.
4. Select Connect. The Communication Path window is displayed.
5. Click Modem direct, then OK.
6. Click Dialing and select AWM ISDN1 Internet (PPP over ISDN).
7. Dial the customer phone number and click OK.
8. Type in the appropriate password according to your user mode, as follows:
• Expert: pbxk1064
• EasyPlus: kilo1987
• Easy: help1954
Note:
The PC and B1 lights on the modem should light up when the connection is established.
The configuration session is open.

Remote Access to the ISDN Modem

When an ISDN modem is used, it is necessary to reserve a DDI number in the public
numbering plan to be able to establish remote access.
If no DDI number is available, check whether the system's ISDN modem access is in the
default attendant group (default group). In this case it is not necessary to keep a DDI number.
Remark:
If the modem is not currently in the attendant group, it is useful to set the Reroutdata flag to the value
01H. The system then automatically recognizes the ISDN service corresponding to the incoming call and
looks in the default attendant group for a data terminal.

6.2.3.4.2 Remote Access By The Analog Modem

Analog Modem (recommended)
Alcatel-Lucent OmniPCX Office Communication Server is equipped with an analog modem
V34 for remote access through the public network. This modem provides a point-to-point
communication link accessible via standard LINUX protocols (PPP, etc.).
Its main characteristics are:
- V34 Modem

6-14              

Downloaded from www.Manualslib.com manuals search engine

 *

- Maximum transmission speed: 33600 bds

- Hayes protocol
In the current version of the system, the V34 "US Robotic" modem has been validated. The
other types of modems were not validated.
Installation Process of the Remote Access by Analog Modem
Follow the procedures described in the previous paragraphs, but replace the FRITZ modem
with the US Robotics analog modem.
Remote Access to the Analog Modem
When the analog modem is used, it is necessary to hold a DDI number in the public numbering
plan in order to be able to carry out remote maintenance.
In the case of no DDI number is available, the access to the modem will be possible only via
the operator transfer.
6.2.3.4.3 Operating Mode
1. Open OMC on the remote access PC.
2. Select the Expert menu.
3. Click Comm.
4. Select Connect. The Communication Path window is displayed.
5. Click Modem direct, then OK.
6. There are two ways of establishing a remote connection:
• Select a modem phone book entry in the Used Entry field of the Modem Connection
window.
• Click Dialing, select the modem to use ("used modem"), then dial the customer remote
access number in the Number field.
7. Enter the system's default password pbxk1064. It will take a few seconds for the
connection to be established.
6.2.3.4.4 Security
In the remote access, the protocol used in the "data link" OSI layer is PPP (Point-to-Point
Protocol). The TCP/IP protocols are used respectively in the "transport" and "network" layers.
For each layer, Alcatel-Lucent OmniPCX Office Communication Server carries out an access
control.
Authentication
At the start of the connection (PPP), an account name (system masked) and password
(pbxk1064) are required. This account name is automatically generated by OMC. The
password is required by OMC to establish a direct connection (LAN) with Alcatel-Lucent
OmniPCX Office Communication Server. Any other authentication will be rejected.
Firewall
If the system accepts the authentication, the PPP connection will be established, and all the
data packets received on this interface will be filtered according to the following rules:

              6-15

Downloaded from www.Manualslib.com manuals search engine

 Chapter 6 *

All the packets are refused except:

- packets bound for Alcatel-Lucent OmniPCX Office Communication Server FTP server via
two TCP ports preset for the PBX configuration by OMC.
- control packets using the ICMP protocol (Internet Control Message Protocol).
6.2.3.5 Access With Proxy
A proxy server can be added to improve security.
To connect a remote OmniPCX Office via a proxy server, the login dialog box can request a
user account and password to connect to the proxy server.

Figure 6.21: Configuration Example with a Proxy Server

To configure a proxy server:
1. In OMC, select Options > Proxy Parameters from the menu toolbar
The Privileged User Login window opens
2. Enter the Privileged User Password and validate
The Proxy Parameters window opens
3. Enter Proxy parameters:
• No Proxy Used: when this radio button is selected, the proxy server is not used. In this
case, all other fields are disabled
• Use Proxy Server: when this radio button is selected, requests from and to OMC are
sent via a proxy server
• Name/IP Address: enter the name or IP address of the proxy server
• Port: enter the port number used by the proxy server
• Do not use proxy for local address: when this checkbox is validated, requests
are not sent via the proxy server when destination addresses are in the same
subnetwork
• User account in Proxy server: enter the user account for the proxy server
• Password: enter the associated password
If the proxy account and password are incorrect in the above parameters, each login dialog

6-16              

Downloaded from www.Manualslib.com manuals search engine

 *

box, to connect a remote OmniPCX Office, requests the proxy account and the associated
password,
To modify the privileged user password:
- In OMC, select Options > Change Privileged User Password from the menu toolbar
The Change Privileged User Password window opens.
- Enter the Old Password (after installation, the initial password is OMCAdmin)
- Enter the New Password
- Confirm the New Password
Note 1:
If you forget the privileged user password, the only solution is to uninstall and reinstall the OMC.

Note 2:
When OMC is launched from 4760 in online mode, the above mentioned configuration is not applicable.

6.2.4 Downloading the Software

Alcatel-Lucent OmniPCX Office Communication Server is delivered either with:
- A final software including all the countries parameters (OmniPCX Office RCE Small,
Medium, Large platforms delivered in BTCO mode) or
- A software tool (OmniPCX Office RCE Compact platform and OmniPCX Office RCE Small,
Medium, Large platforms delivered in stock mode).
This software tool is installed on the PowerCPU and must be updated with a further system
software package (including the specific country parameters) also called country software,
so that the installation is complete. The country software needs to be downloaded using
OMC.
Important:
System Password management policy
Basic rules have to be applied to the different passwords allowing an OMC connection to the
system. It is recommended to change the default Installer password for OMC Expert,
Administrator password for OMC EasyPlus and Operator password for OMC Easy.
Remember these passwords can also be used from the MMC-Station.
The following are the recommendations for good password management:
- Implement company policy to regularly update all system passwords
- Regularly change the passwords
- Avoid the use of simple passwords such as 12345678, 11111111, 00000000 etc…
- Never choose a word from everyday language. Attackers can use special dictionary cracking
software to retrieve these
- Never choose a word that is closely related to you:
• your company name
• your name
• your wife’s maiden name
• the name of your children or your pet,
• your favourite hobby, etc…

              6-17

Downloaded from www.Manualslib.com manuals search engine

 Chapter 6 *

- Choose a different password for each connection level

- Do not disclose passwords to other persons/colleagues
- Never write down your password. The first thing an attacker will do is rummage through your
personal belongings.
6.2.4.1 Downloading software for Alcatel-Lucent OmniPCX Office Communication
Server (OmniPCX Office RCE Small, Medium, Large platforms delivered in
BTCO mode)
To download the software, proceed as follows:
1. Open OMC.
2. Open the Tools folder.
3. Open the OMC-Software Download application.
4. In the Communication Mode window, select the type of download:
• Local
• Modem Direct
• Modem Call Back
• LAN
5. Enter the password pbxk1064.
6. The OMC-Software Download window opens. This window has several areas:
• A parameter setting area:
• Select the directory containing the descriptor file for the new software release. By
default this file is in the BOOT directory.
Use the Delivery file browse button.
• Select the country for the new software release.
Use the ...Delivery drop down menu in the Country & Supplier... area. As an
indication, the PBX field gives the country of the currently used software release.
• Download all the files (by checking the Download all files box) or just those whose
Action field contains the value Install.
• Save the data.
If the Data saving box is checked, the system automatically saves and restores
the data after having swapped over to the new software release.
If the Data saving box is not checked, you must use OMC to save the data before
starting the download. Restore this data after the download/swap is complete.
• Download the files needed for the Voice over IP features.
Depending on customer needs, check the 8082 My IC Phone box and/or 4135 IP
Conference Phone box (the Voice over IP services box is automatically
checked).
• Select the language of the voice guides to download.
Click on the Languages button to access the Languages Download window.
• Define a time zone by selecting a city and country.
Click on the Time Zone button to access the Time Zones Download window.
• Define the software swap mode.
In the Software Exchange area, there are two possible choices:
Click on the After OMC disconnect button to swap immediately. The swap starts
when you quit the downloading application.

6-18              

Downloaded from www.Manualslib.com manuals search engine

 *

Click on the Date button and indicate the required date and time for a delayed
swap.
Remark:
If you select immediate switching, it will take effect as soon as you quit the download
application.
• A read only zone
• The Downloadable Item area allows you to see the different versions of the
applications.
• The Action column lists the files to download.
• The bottom part of the window shows download progress. Each downloading and
acknowledgement action produces a message.
7. Click Start to start downloading.
6.2.4.2 Downloading software for OmniPCX Office RCE Compact platform (and
OmniPCX Office RCE Small, Medium, Large platforms delivered in stock
mode)

Remark:
Because the OmniPCX Office RCE Compact platform does not use internal backup batteries like the
other OmniPCX Office RCE Small, Medium, Large platforms, it is important not to cut off the cabinet's
main power supply during software download. Any power shut down during the BIOS downloading will
damage the PowerCPU.
To download the software, proceed as follows:
1. From OMC, connect to the system.
If it is the first connection to the system, a Warning window is automatically displayed.
2. Click on the Download button.
3. Enter the IP address and the password of the PC.
The OMC - Software download window is displayed.
4. In the Delivery file field, select the path to access the system software installed on your
PC.
5. Using the ...Delivery drop-down menu in the Country & Supplier... area, select the
country where the system will be installed.
6. Click Start.
When download is complete, the message Session successfully finished is displayed.
7. Click Exit to quit the downloading tool. The system will swap on the new software version
and will be available within a few minutes.
Note:
When available, a new Uboot-loader (similar to the BIOS in previous releases) version in the OmniPCX
Office RCE Compact software will not be automatically included in the list of items to be downloaded
from the system. You must select and include the new Uboot-loader version manually.

6.2.5 Services provided

OMC offers five operating modes:

              6-19

Downloaded from www.Manualslib.com manuals search engine

 Chapter 6 *

1. Mode 1: Data and tool repository

2. Mode 2: Typical installation
3. Mode 3: Typical modification
4. Mode 4: Expert
5. Mode 5: Multisite
Important:
Access to modes 2, 3, 4 and 5 is password protected: pbxk1064 (using the OMC tool)
Access to modes 2 and 3 is password protected: help1954 (using the OMC Easy tool)

6.2.5.1 Mode 1: Data and tool repository

This mode is used to create .crp files offline (collective customer directories) which are used in
the Typical Installation menu.
6.2.5.2 Mode 2: Typical installation
This mode is used for online manual programming by choosing between Company and Hotel
and automatically on-line using .crp files.
Remark:
The choice Company/Hotel is only offered once. It is necessary to perform a cold reset to see it again.

6.2.5.2.1 Initial Business Installation Wizard

- IP configuration
- Default Numbering Plan
- Installation number
- Operating mode
- Channels and Bundles
- DECT ARI
- Creation of DECT handsets
- Metering
- Date and time
- Terminal List
- Various Subscribers
- Collective speed dial
- OS groups
- Call groups
- Broadcast groups
- Intercept groups
- Screening
6.2.5.2.2 Initial Hotel Installation Wizard

6-20              

Downloaded from www.Manualslib.com manuals search engine

 *

As well as the Business configuration, this wizard can be used to configure terminal numbers
in the hotel rooms.
6.2.5.2.3 Installation Wizard
This wizard enables you to use a .crp type file created under Data and tool repository ->
Information Repository Wizard.
Follow the instructions; if the data is accepted it is transmitted to the system which is then
reset.
6.2.5.3 Mode 3: Typical modification
The 5 icons available in this mode (Terminals, Groups, System, Collective Directory and
External Lines) are used to gain access to the wizards used to modify or configure simply
various parameters as detailed below.
The data will be taken into account by the system after clicking OK.
6.2.5.3.1 Subscribers
- List of subscribers: public number, name, discrimination level, accessible network line
groups.
- Dividing calls between normal mode and restricted mode.
- EasyPlus View: detailed parameters for each subscriber: keys, languages, authorized
usage, personal code, callbacks, dynamic forwarding, personal directory, etc.
6.2.5.3.2 Groups
- OS Groups
• Making groups: introducing members into each group
• Assigning a welcome message to each group
- Call Groups
• Name and type (parallel, cyclical or sequential)
• Making groups: introducing members into each group
• Assigning a welcome message to each group
- BTS Clusters
• Name of each group
• Making groups: introducing members into each group
- Call pick-up groups
Making groups: introducing members into each group
6.2.5.3.3 Collective Speed Dial
The name and destination number of the call for each entry.
6.2.5.3.4 System
- Default numbering plans
• Choose between national numbering plans or a 2, 3 or 4-digit star plan.
• EasyPlus View: Normal service public numbering plan
• EasyPlus View: Restricted service public numbering plan

              6-21

Downloaded from www.Manualslib.com manuals search engine

 Chapter 6 *

• EasyPlus View: Order codes

• EasyPlus View: Internal numbering plan
- Installation numbers
• International code
• National code
• Installation number
• EasyPlus View: Call back prefix
• EasyPlus View: Customized caller number
• EasyPlus View: Private installation number
- Metering
• Cost of telephone metering
• EasyPlus View: Hotel metering cost for current currency unit (VAT, prepayment
amount, etc.)
• EasyPlus View: Metering options for current monetary unit
• EasyPlus View: Print parameters
• EasyPlus View: Metering options for replacement currency (Euro)
- Date and time
- Software keys
• System Key
• CTI Key
6.2.5.3.5 External Lines
- B-Channel number
- External number for incoming calls (DISA)
- Type of dialling
6.2.5.4 Mode 4: Expert
This mode cannot be accessed from OMCEasy.
This mode allows all modification and system maintenance. The wizards available in modes 2
and 3 are also accessible.
6.2.5.5 Mode 5: Multisite
This new mode is available with Easy, EasyPlus and Expert Views. It allows you to manage
several Alcatel-Lucent OmniPCX Office Communication Server systems.
The Multisite feature includes the following basic services:
- An Installation Wizard to help installers and administrators to set up appropriate
configurations when adding PBXs to a network.
- The automatic replication of data common to all networked PBXs. Common data is pushed
from a reference PBX to all other secondary PBXs in the network.
- The automatic synchronization of Phonebook names and phone numbers.
Note:
The OMC Multisite feature is designed for setting up PBX networks from scratch. Large parts of the PBX

6-22              

Downloaded from www.Manualslib.com manuals search engine

 *

settings are overwritten when configured PBXs are added to a network.

              6-23

Downloaded from www.Manualslib.com manuals search engine

 Chapter 6 *

6-24              

Downloaded from www.Manualslib.com manuals search engine

   
"    

7.1 Maintenance Level 1

7.1.1 Maintenance
This module provides maintenance advice on different hardware components of the
Alcatel-Lucent OmniPCX Office Communication Server system.
7.1.1.1 Battery Maintenance
Alcatel-Lucent OmniPCX Office Communication Server systems (except the OmniPCX Office
RCE Compact) are supplied with internal batteries that provide back-up power in the event of a
mains power failure. Alternatively, all systems may be optionally equipped with an external
battery pack to provide back-up power.
To guarantee system shutdown without data loss in the event of a mains power failure or if the
mains plug is unplugged from the wall socket, replace the batteries every two years. This
maintenance operation is vital to guarantee sufficient power autonomy to allow the files to be
saved before the system shuts down.
Before replacing batteries, the system must be powered down and the power cable removed
from the mains supply.
- To replace internal batteries, the rear panel of the system cabinet must be removed and
the battery drawer pulled out.
- To replace external batteries, the external battery box must be opened.
To maintain a good balance, replace all the batteries at the same time with

batteries of the same type, from the same manufacturer and from the same batch.
Make sure you respect the correct polarities when replacing batteries. There is a

risk of explosion if the batteries are incorrectly replaced. Used batteries must be
disposed of according to the battery manufacturer's instructions.
The batteries are supplied uncharged. File saving in the event of a power failure can only be
guaranteed once the batteries have been charged; that is, about 12 hours after turning on the
system (PowerCPU switch in ON position).
7.1.1.1.1 Internal Battery Characteristics
- number: 1 (OmniPCX Office RCE Small), 2 in parallel (OmniPCX Office RCE Medium) or 3
in series (OmniPCX Office RCE Large)
- sealed lead battery
- 1,2 Ah / 12 V
- fire resistance better than or equal to UL94-V2
7.1.1.1.2 External Battery Characteristics
- number: up to 2 for OmniPCX Office RCE Compact, up to 3 for OmniPCX Office RCE
Small and OmniPCX Office RCE Medium platforms, up to 6 for OmniPCX Office RCE

              7-1

Downloaded from www.Manualslib.com manuals search engine

 Chapter 7  $ % $

Large platforms
- sealed lead battery
- 7 Ah / 12 V
- fire resistance better than or equal to UL94-V2
7.1.1.2 Board Battery Maintenance
It is recommended that the batteries in the PowerCPU boards should be replaced by batteries
of the same type every two years. Dead batteries must be disposed of according to the battery
manufacturer's instructions.
7.1.1.3 Maintenance of Ventilation System
At the same time as replacing the batteries, clean the system ventilation holes using a brush or
a lint-free cloth.
When a fan fails, only the T0/T2 external digital accesses and the first two interfaces of the
digital stations remain operational.
7.1.1.4 Replacing the PowerCPU Board
It is necessary to adapt the software key after replacing the PowerCPU board.
1. The new PowerCPU board has no software key:
• You know the new software key corresponding to the new PowerCPU:
• Reboot the system with the new PowerCPU: the system operates with default
functionality
• Load the new key using OMC; Procedure with MMC Station
• Do a cold reset: the system operates with the possibilities offered by the new key
• Restore the configuration (not the old key)
• You do not know the new key corresponding to the new PowerCPU: use the old key
until you can enter the new one (you have 30 days). The remaining actions are
identical to those shown in the previous section
2. The new PowerCPU software key corresponds to the serial number:
• The new key offers the desired level of service:
• Reboot the system with the new PowerCPU: the system operates with the desired
level of service
• Restore the configuration (not the old key)
• The new key does not offer the desired level of service: change the key
3. The new PowerCPU board software key does not match the serial number:
One is in the same situation as case 1, except that the system boots with the level of
service offered by the key on the PowerCPU, with temporary validity.
7.1.1.5 Adding and Replacing Interface Boards
This section describes how to add an interface board into a vacant slot in the system and how
to replace an existing board with a new one.
Note:
Always take anti-static precautions when handling boards. Before coming into direct physical
contact with a board, make sure you touch a grounded metal surface to remove static charge

7-2              

Downloaded from www.Manualslib.com manuals search engine

  $ % $

from your body. When holding a board, always wear a grounding device such as a grounded wrist
strap, and do not touch board components that are sensitive to static charge.
Before attempting board installation/exchange, note the following system rules concerning the
detection of boards:
- A detected board is considered to be PRESENT
- A PRESENT board can be ACCEPTED or REFUSED, depending on the system
dimensioning criteria
- On a cold reset, all PRESENT boards are taken into account (irrespective of whether they
are ACCEPTED or REFUSED)
- A board which is PRESENT on a cold reset can later be determined as ABSENT on a
warm reset if in the meantime the board has been unplugged or there has been a board
detection failure
- After a cold or warm reset, new boards are always taken into account and declared as
PRESENT (and then ACCEPTED or REFUSED)
The following table describes situations more specifically relevant to plugging/unplugging
boards.
Situation Description
A board is plugged into a slot never before The board is detected as PRESENT and then
occupied determined to be ACCEPTED or REFUSED
A board is replaced with another board of (according to configuration criteria, such as
the same type authorized positions and maximum hardware
capacity). If the board is accepted, its accesses
are taken into account depending on the system
dimensioning criteria.
A board is replaced with another board of a As above, except when the replacement board is
different type plugged in, configuration data for the previous
board is cleared.
A PRESENT and ACCEPTED board is The board's disappearance is detected and the
unplugged board is considered as out of order and then
ABSENT. However, configuration data
associated with the unplugged board remains
available.
A PRESENT and REFUSED board is The board's disappearance is detected and the
unplugged board is considered as ABSENT. However,
configuration data associated with the unplugged
board remains available.

7.1.1.5.1 Adding a board into a vacant slot

The procedure presented below assumes that a board is to be installed in a vacant slot in the
system cabinet.
Note 1:
Hot installation is forbidden in OmniPCX Office RCE Compact platforms. It is also forbidden for
PowerCPU boards in all platforms.
1. If a hot installation is not possible, stop the system and disconnect it from the mains power
supply.

              7-3

Downloaded from www.Manualslib.com manuals search engine

 Chapter 7  $ % $

2. Locate the required vacant slot in the cabinet and remove the metal plate for this slot.
3. Taking anti-static precautions (for example, by wearing a grounded wrist strap), pick up the
new board and plug it into the vacant slot.
4. Secure the end-plate of the board to the cabinet with the screw provided.
5. If you have stopped and powered down the system, reconnect it to the mains power supply
and restart it.
6. Perform any configuration and/or tests required for the new board.
Note 2:
Following configuration in the OMC tool, you may be required to perform a warm reset of the system for
the configuration changes to take effect. In this case, the software will prompt you to perform the warm
reset.

7.1.1.5.2 Replacing an existing board

The procedure presented below assumes that an existing board is to be removed from the
system and a replacement board (of the same or different type) is to be installed in the same
slot in the system cabinet.
Note 1:
Hot swap is forbidden in OmniPCX Office RCE Compact. It is also forbidden for PowerCPU
boards in all systems.
1. If a hot swap is not possible, stop the system and disconnect it from the mains power
supply.
2. Locate the existing board to be removed in the cabinet and unscrew the securing screw
from its end-plate.
3. Taking anti-static precautions (for example, by wearing a grounded wrist strap), pull the
board out of its slot.
4. Taking anti-static precautions, pick up the replacement board and plug it into the now
vacant slot.
5. Secure the end-plate of the board to the cabinet with the screw provided.
6. If you have stopped and powered down the system, reconnect it to the mains power supply
and restart it.
7. Perform any configuration and/or tests required for the replacement board.
Note 2:
Following configuration in the OMC tool, you may be required to perform a warm reset of the system for
the configuration changes to take effect. In this case, the software will prompt you to perform the warm
reset.

7.1.1.6 Hard Disk Maintenance

Please comply with the recommendations given below; any mistreatment of the hard
disk (handling, transport, storage) can result in a shortened life and possible
malfunctioning of your installation.
7.1.1.6.1 Handling

7-4              

Downloaded from www.Manualslib.com manuals search engine

  $ % $

- Always wear a discharge device (bracelet, heel clip, etc.) to protect against electrostatic
discharges.
- Avoid any knocks to the hard disk
- Do not touch the connector
- Handle the disk by holding it by the sides
7.1.1.6.2 Storage
- All hard disks must be stored in an electrostatic protective bag
- Avoid contact between hard disks
- Do not pile them up (even when packed)
7.1.1.6.3 Transport.
- A hard disk can only be transported when packed in an electrostatic protective bag
- Avoid contact between hard disks
- Use standard packaging suited to transporting hard disks

              7-5

Downloaded from www.Manualslib.com manuals search engine

 Chapter 7  $ % $

7-6              

Downloaded from www.Manualslib.com manuals search engine

   
  

8.1 Glossary

8.1.1 A
ACD
Automatic Call Distribution. A computerized phone system that responds to the caller with a voice menu,
and connects the call to the required agent. It can also control call flows by automatically routing calls in the
order of arrival.
ACSE
Association Control Service Element. OSI convention used for establishing, maintaining and releasing
connections between two applications.
ADN
Additional Designation Number.
AFU-1
Auxiliary Function Unit. Daughter board of the PowerCPU board supporting ancillary functions such as
general bell, doorphone, audio in, audio out, etc.
AMIX-1
Mixed analog equipment board: analog accesses with CLIP functionalities, analog and digital terminal
connection interfaces.
AP
Access Point. A device that acts as a switch between the wireless LAN (802.11a, b, or g) and the wired
LAN (802.3). There are two types of APs: Thin and Fat. The newer Thin technology AP consists of a thin
AP and an access controller (also known as a wireless controller). Only the time-critical functions are
managed by the thin AP. The other features are managed by the access controller.
APA
Analog Public Access. Board allowing the connection of analog network lines (switched network) with CLIP
functionality. That board, equipped with GSCLI boards (Ground Start), is compatible with the American
public network.
API
Application Programming Interface
ARI
Access Right Identifier. System identification number (DECT feature).
ARS
Automatic Route Selection. A logic direction is a set of trunks used for a call with the following facilities:
seeking out the optimal path for a call, using the least-cost operator or network; overflow management:
enables a PCX to find a new route to make an outgoing call when there are no resources available in the
initial trunk.
ASN-1
Abstract Syntax Notation 1. OSI language for describing data types independently of processor structures
and technical representations.
ATA
Analog Trunk Access. Board for connecting analog network lines (switched network).

8.1.2 B
BACKGROUND MUSIC
External device (e.g. radio tuner) that can broadcast music over the loudspeakers of idle terminals;
broadcasting is stopped automatically if there is an incoming call to the terminal or if the user makes a call.

              8-1

Downloaded from www.Manualslib.com manuals search engine

 Chapter 8  

BACP
Bandwidth Allocation Control Protocol. Control protocol associated with BAP.
BAP
Bandwidth Allocation Protocol. PPP protocol that manages bandwidth by allocating it dynamically between
two ports, i.e. between the two extremities of a point-to-point link.
BOD
Bandwidth On Demand. Service that allocates bandwidth automatically in response to traffic volume.
BRA
Basic Rate Access. Board for connecting T0 or DLT0 digital basic accesses; each access supports a data
rate of 144 kbps, structured as 2 B-channels at 64 kbps for voice and data transmission, and 1 D-channel
at 16 kbps for signaling.
BTCO
Build To Customer Order.

8.1.3 C
CA
Certificate Authority.
CCP
Compression Control Protocol.
CHAP
Challenge-Handshake Authentication Protocol. Security function supported on connections that use PPP
encapsulation: prevents unauthorized access.
CIFS
Common Internet File System. This protocol is an extension to the SMB file sharing system. Its main benefit
is to provide compatibility with locking operations and multiple SMB read/write operations.
CLIP
Calling Line Identification Presentation. Complementary service for digital protocols that allows the caller
number to be presented to the called party.
CLIR/COLR
Calling/COnnected Line Identification Restriction. Service that inhibits CLIP or COLP.
CNIP
Calling Name Identification Presentation. Complementary service for private digital protocols (ISVPN or
ABC-F) that allows the caller's name to be presented to the called party.
COLP
COnnected Line identification Presentation. Complementary service for digital protocols that allows the
number of the connected user (the one who answers the call) to be presented to the caller.
CONP
COnnected Name identification Presentation. Complementary service for private digital protocols (ISVPN or
ABC-F) that allows the name of the connected user (the one who answers the call) to be presented to the
caller.
CPU
Central Processing Unit. Term designating the processor or microprocessor. The central processing unit
executes computer program instructions.
CSTA
Computer Supported Telephony Application. ECMA standard that defines command exchanges between a
PCX and a server.
CTI
Computer-Telephone Integration. Interaction mechanism between 2 sections, namely a data processing
section (computer) and a telecommunications section (PCX), independently of the physical layout of the 2
sections.
CTL

8-2              

Downloaded from www.Manualslib.com manuals search engine

  

Certificates Trust List.

8.1.4 D
DASS2
Digital Access Signaling Specification number 2
DDI
Direct Dialing In. Direct external call number for the system terminals (depending on the configuration with
the public network operator).
DECT
Digital Enhanced Cordless Telecommunication. European cordless telephony standard. DECT terminal:
cordless terminal that complies with this standard.
DHCP
Dynamic Host Configuration Protocol. Protocol that manages IP address allocation dynamically so that
addresses can be reassigned when no longer being used by LAN hosts.
Direct RTP
A feature which optimizes the RTP flow of VoIP in SIP, thus optimizing the number of VoIP CODEC
resources.
DISA
Direct Inward Station Access. Services (Analog DISA and Transit DISA) enabling outside callers to dial a
specific number giving direct access to the system.
DLL
Dynamic Link Library. Windows library linked dynamically to an application.
DLT0
Digital Line T0. Basic access configured with the QSIG protocol (= digital LIA).
DLT2
Digital Line T2. Private 2 MHz link in PRA mode (= digital ATL).
DNS
Domain Name Server. System used on the Internet for converting domain names or machine names into IP
addresses. A domain name, unlike an IP address, is an easily memorized Internet address.

8.1.5 E
ECMA
European Computer Manufacturers Association
Entity
In this PBX context, an Entity refers to a group of users.
ETHERNET
Local network (LAN) operating at 10 or 100 Mbps (10 base T or 100 base T) over a coaxial cable. Ethernet
is similar to the IEEE 802.3-series standards.

8.1.6 F
FoIP
Fax over IP. Refers to the message and data transmission from a G3 Fax using the Internet protocol (T38
or Fax over G711 with SIP).
FTP
File Transfer Protocol. Standard protocol for exchanging files between remote computers over the Internet.
FTP/STP/UTP
Foiled Twisted Pairs/Shielded Twisted Pairs/Unshielded Twisted Pairs. Types of connection cables to be
used between an Alcatel-Lucent OmniPCX Office Communication Server and an external distribution panel.

              8-3

Downloaded from www.Manualslib.com manuals search engine

 Chapter 8  

8.1.7 G
G.722
ITU–T 7 kHz wideband speech codec based on sub-band adaptive differential pulse code modulation
(SB-ADPCM) within a bit rate of 48, 56 or 64 kbit/s.
GATEKEEPER
Secure directory server
GATEWAY
Device connecting different networks
GENERAL BELL
If the operator is absent, internal and external calls to the operator are directed to an external signaling
device that lets any authorized terminal take these calls.

8.1.8 H
H.323
ITU standard for multimedia communication (voice, video, data).
H.450
Additional services associated with H.323 version 2.
HSL
High Speed Link. Link between the basic module and a module expansion; requires an HSL daughter
board to be fitted on the PowerCPU and PowerMEX boards.
HTTP
HyperText Transfer Protocol. Standard application protocol for exchanging files (text, images, audio, video,
etc.) over the Internet.
HTTPS
Secure HyperText Transfer Protocol. Secure version of HTTP: encrypts and decrypts pages containing
user requests as well as pages retrieved from a web server.

8.1.9 I
IAP
Internet Access Provider. See ISP.
IBS
Intelligent Base Station. There are 2 kinds of IBSs: one that can be installed indoors, one outdoors.
ICMP
Internet Control Message Protocol. Network protocol that provides error reports and information on the
processing of IP packets.
IMAP4
Internet Message Access Protocol. A protocol of the same type as POP3, the difference being that the
messages always stay on the ISP server, even after consultation. IMAP requires continuous access to the
server while the messaging service is in use.
IN
Installation Number
IP
Internet Protocol. The main protocol supporting the Internet. IP governs the forwarding and transmission of
data packets over supporting multivendor packet-switched networks.
IPSec
Internet Protocol Security. Standard taking network security into account. Protocol used in the
implementation of VPNs, and for remote access by connection to a VPN.
ISDN

8-4              

Downloaded from www.Manualslib.com manuals search engine

  

Integrated Services Digital Network. Standard for the transmission of digital data over telephone cables or
other communication vectors.
ISDN-EFM
Integrated Services Digital Network- Emergency Forwarding Module. T0/S0 Forwarding Module.
ISP
Internet Service Provider. Internet Access Provider. A company that provides Internet access for individuals
and companies, along with other services, such as web site construction and hosting.
ISVPN
Integrated Services Virtual Private Network. Protocol used in a private virtual digital network; it offers
functions such as transfer optimization and the transmission of information such as the name, busy status
or diversions.
ISVPN+
Includes metering information in addition to the usual ISVPN services.
ITU
International Telecommunications Union : global coordination body.
IVPS
Virtual card, embedded on the CPU board, supporting a voice mail application.

8.1.10 K
KEY SYSTEM (mode)
Dedicated terminal operating mode in which the terminal features as many resource keys (RSP) as there
are network lines in the system.

8.1.11 L
LAN
Local Area Network. Network of interconnected switches, routers, and servers that share the resources of a
processor or server in a relatively restricted geographical area, usually the premises of a company. In the
context of the OmniPCX Office, the LAN includes an IP network and provides services to the wired client
and to the WLAN client: file server, proxy, main server.
LDAP
Lightweight Directory Access Protocol for access to directory services managed by a directory server.
LOUDSPEAKER
External loudspeaker used for broadcasting messages.

8.1.12 M
MANAGER/SECRETARY
Set of specific services (profile, filtering, diversion) between a manager terminal and a secretary terminal.
MIX
Mixed equipment board: T0 accesses, analog and digital terminal connection interfaces.
MLAA
Multiple Automated Attendant: Software component used for automatic incoming calls routing via voice
guides.
MMC
Man Machine Configuration. Command lines that a user types to the interface of an application to change
the parameters of system elements. It can also be in the form of graphic images that the user can select to
make changes.
MPPP
Multi-link PPP. A protocol that aggregates bandwidth from a number of links to obtain faster communication
speeds.

              8-5

Downloaded from www.Manualslib.com manuals search engine

 Chapter 8  

MULTILINE TERMINAL
Terminal that has several lines for managing several calls at the same time.

8.1.13 N
NAT
Network Address Translation. A service that converts the IP address used on one network into another IP
address recognizable by another network. Address translation allows companies to keep their own private
IP addresses for internal purposes, while using just one IP address for external communication.
NMC
Network Management Center. Workstation allowing a communication server administrator to remotely
manage, administer (storage of call metering tickets for example) and optimize one or more Alcatel-Lucent
OmniPCX Office Communication Server systems.
NMT
Numbering Modification Table
NNTP
Network News Transfer Protocol. Protocol used by computers to handle messages created in Usenet
forums.

8.1.14 O
ODC
On Demand Communication - Commercial name of On Demand mode.
On Demand mode
This licence mode introduces a “user” definition and the validity of the license in OPEN state is limited and
daily checked by the system.
OS
Operator Station. Dedicated terminal for answering incoming calls from the public network.
OMC
OmniPCX Office Management Console (formerly PM5). A PC-based management and configuration tool.

8.1.15 P
PAP
Password Authentication Procedure. Procedure used by PPP servers to validate connection requests.
PASSWORD
Code acting as a password, controlling access to the voice mail unit and the terminal locking function.
PAT
Port Address Translation
PCBT
PC Based Telephony
PCX (mode)
Mode of operation of dedicated terminals; in this mode, all the network lines are materialized by
general-purpose resource keys (RSB).
PE
Public Exchange. Public central terminal (switch).
PLEASE WAIT MESSAGE
An audio component of the system (or an external device, such as a cassette player) which plays a
message or piece of music while keeping an external correspondent on hold.
POP3
Post Office Protocol. Standard Internet protocol for receiving electronic messages. POP3 is a client/server
protocol in which the messages are received and hosted by the ISP. When a message is read, it is

8-6              

Downloaded from www.Manualslib.com manuals search engine

  

transferred to the client terminal and is no longer hosted by the ISP.

PowerMEX
Module expansion. Controller board for extension or module expansion.
PPP
Point-to-Point Protocol. Protocol used in communication between two computers using a serial interface
(typically a PC connected to a server via a telephone line).
PRA
Primary Rate Access. Board for connecting a T2 digital primary access; the access supports 48 kbps
structured as 30 B-channels at 64 kbps for voice and data transmission, and 1 D-channel at 64 kbps for
signaling.
PROXY
A proxy server is used as an interface between a user and the external Internet network.
PSTN
Public Switched Telephone Network.
PTN(X)
Private Telecommunications Network (eXchange). A private network consisting of switches and terminals
connected together by telephone links.
PWT
Personal Wireless Telecommunications. Corresponds to the DECT standard for the North American
countries (especially the US).

8.1.16 Q
QOS
Quality Of Service. Network characteristics (transmission speed, etc.) can be measured, improved and, to
some extent, guaranteed in advance.
QSIG
Q Signaling Protocol. Set of standard signaling protocols between the private PBXs of a telephone network
(Q reference point) interconnected by digital ATLs.

8.1.17 R
RADIUS
Remote Authentication Dial-In User Service. A client/server protocol that enables remote access servers to
communicate with a central server in order to authenticate remote users before allowing them access to the
systems or services they have requested.
RAS
Remote Access Server. Remote access server to the system LAN.
RCE
Rich Communication Edition (for example, OmniPCX Office RCE Compact is the short designation for
Alcatel-Lucent OmniPCX Office Rich Communication Edition Compact).
RGO, RGI, RGM
General resource keys supporting local and/or external calls, whether outgoing (RGO), incoming (RGI), or
mixed (RGM).
RNIS
"Réseau Numérique à Intégration de Services". French equivalent of ISDN.
ROSE
Remote Operations Service Element
RSB
Resource key dedicated to a trunk group (bundle); used for making external outgoing calls on a particular
trunk group, and receiving all network calls.
RSD

              8-7

Downloaded from www.Manualslib.com manuals search engine

 Chapter 8  

Resource key for a particular destination; supports local calls for this number if assigned to a speed dial
number, incoming calls for the number if assigned to a DDI number, or outgoing calls on a trunk group if
assigned to a trunk group.
RSL
Resource key dedicated to a set; supports calls to and from a particular set.

8.1.18 S
SATA
Serial Advanced Technology Attachment - Hard disk interface bus.
S0 BUS
Type of connection for S0 digital terminals (passive short bus, long/short point-to-point bus, extended bus);
S0 buses and terminals are connected up via an S0 option embedded in an Alcatel Reflexes terminal.
SD Card
Secure Digital card can provide the memory necessary for all features and functions on the PowerCPU.
SELV
Safety Extra Low Voltage. Classification of interfaces in accordance with standards EN60950 and IEC 950.
SIP
Session Initiation Protocol. A signaling protocol for Internet conferencing, telephony, events notification, and
instant messaging. SIP initiates for example, call setup, routing and authentication within an IP domain.
SLI
Single Line Interface. Board allowing the connection of analog terminals (also known as Z terminals).
SMB
Server Message Block. File sharing protocol which enables a terminal to localize one or more files across
the network, and then to open/read/edit/delete them.
SMTP
Simple Mail Transfer Protocol. Standard protocol used for sending and receiving mails.
SPI
Service Provider Interface
SSH
Secure Shell. A UNIX interface protocol for obtaining secure access to remote computers.
SSID
Service Set Identifier. In Wi-Fi wireless LAN computer networking, an SSID is a code attached to all
packets on a wireless network to identify each packet as part of that network. The code consists of a
maximum of 32 alphanumeric characters. All wireless devices attempting to communicate with each other
must share the same SSID. Apart from identifying each packet, the SSID also serves to uniquely identify a
group of wireless network devices used in a given "Service Set".
SSL
Secure Socket Layer. Encryption and authentication layer which ensures the authentication, integrity and
privacy of the documents distributed by the World Wide Web.

8.1.19 T
TAPI
Telephony API (Application Programming Interface). Standard defined by Microsoft.
TCP/IP
Transmission Control Protocol/Internet Protocol. Standard protocol used on the Internet. TCP corresponds
to the Transport layer (layer 4) of the OSI model. IP corresponds to the Network layer (layer 3) of the OSI
model.
TERMINAL GROUP
Series of terminals grouped under the same directory number. Any call to that number is routed to a free
terminal line.

8-8              

Downloaded from www.Manualslib.com manuals search engine

  

TFTP
Trivial File Transfer Protocol. The simplest network application for transferring files.
TL
(Analog) Trunk Line connecting the system to the public switched network.
TLS
Transport Layer Security.
TSAPI
Telephony Services API. Standard defined by Novell, based on ECMA's CSTA standard.
TSP
Telephony Service Provider. TAPI driver used to access to telephony devices (modem, phone set, etc.).

8.1.20 U
UAI
Universal Alcatel Interface. Board used for connecting up digital terminals or DECT 4070 IO/EO base
stations.
UDA
Universal Directory Access offering the possibility to use the company directory or an external LDAP
directory when it exists to find a listed contact.
UPS
Uninterruptible Power Supply. Device increasing the system's backup time.
URL
Uniform Resource Locator. Address of a resource (file, program, image, etc.) accessible on the Internet.
UUS
User to User Signaling. Information carried clear end-to-end by ISDN to enable exchanges between
network subscribers; the ISVPN protocol is contained within this information.

8.1.21 V
VMU
Voice Mail Unit. The integrated voice server provides a voice mailbox for each user, as well as a general
voice mailbox and features such as Personal Assistant, Automatic Attendant and Audiotex.
VoIP
Voice over IP. Term designating voice transmission over a data network using the Internet protocol.
VoWLAN
Voice over WLAN. Term designating voice transmission over a data network using the WLAN.
VPN
Virtual Private Network. Private data network that uses the public telecommunications infrastructure (e.g.
the Internet) while maintaining confidentiality by means of tunneling protocols and security procedures.

8.1.22 W
WAN
Wide Area Network. A geographically dispersed telecommunications network. The term WAN is used in
contrast to LAN.
WIFI
Wireless Fidelity.
WINS
Windows Internet Naming Service. In Windows environment, the service that manages the correspondence
between client station names and LAN locations relative to their IP addresses.
WLAN
Wireless Local Area Network. A LAN that provides networking using radio frequencies rather than wires for

              8-9

Downloaded from www.Manualslib.com manuals search engine

 Chapter 8  

communication.
WLAN association
An association refers to the connection between the WLAN client and the AP. There are two types of
associations: passive scanning and active scanning. In passive scanning, APs send out information such
as SSIDs and supported rates, while the client passively scans the radio channels for beacons and probe
responses. The client then selects an AP. The client keeps scanning even after the association is made (to
support roaming). In active scanning, clients send out probe requests. If the probe request contains an
SSID, only the APs with the correct SSID will respond. If the probe request contains a broadcast, all the
APs will respond.
WLAN client
Any PC, PDA, or phone set that supports the 802.11a and 802.11b/g protocols can be a WLAN client.
WLAN handset
A wireless terminal that is connected to the system through a wired Access Point (AP). The radio
connection between the wireless terminal and the AP is specified by the 802.11 family of specifications.
The WLAN handset range includes Alcatel-Lucent IP Touch 310/610 WLAN Handsets and Alcatel-Lucent
OmniTouch 8118/8128 WLAN Handsets. WLAN handsets are sometimes referred to as MIPT (Mobile IP
Touch) handsets.

8-10              

Downloaded from www.Manualslib.com manuals search engine